SCOPE: IMPROVED, QUAD, SPST, CMOS ANALOG MULTIPLEXER Device Type 01 02 Generic Number DG441A(x)/883B DG442A(x)/883B Case Outline(s). The case outlines shall be designated in Mil-Std-1835 and as follows: Outline Letter K Z Mil-Std-1835 GDIP1-T16 or CDIP2-T16 CQCC1-N20 Case Outline Package Code 16 LEAD CERDIP J16 20-Pin Ceramic LCC L20 Absolute Maximum Ratings Voltage Referenced to VV+ to V- .............................................................................................................................. 44V V- to GND .......................................................................................................................... 25V VL ................................................................................................... (GND-0.3V) to V+ +0.3V) Digital Inputs, VS, VD 1/ ..........................................................................(V -) -2V to (V+ )+2V or 30mA whichever occurs first Continuous Current, Any terminal .................................................................................. 30mA Peak Current, S or D (Pulsed at 1ms, 10% duty cycle max) ......................................... 100mA Lead Temperature (soldering, 10 seconds) ........................................................................ +300C Storage Temperature ........................................................................................... -65C to +150C Continuous Power Dissipation .................................................................................. TA=+70C 16 lead CERDIP(derate 10.0mW/C above +70C) ....................................................... 800mW 20 lead LCC (derate 9.1mW/C above +70C) .............................................................. 727mW Junction Temperature TJ .............................................................................................. +150C Thermal Resistance, Junction to Case, JC: Case Outline 16 lead CERDIP......................................................................... 50C/W Case Outline 20 lead LCC .............................................................................. 20C/W Thermal Resistance, Junction to Ambient, JA: Case Outline 16 lead CERDIP....................................................................... 100C/W Case Outline 20 lead LCC ............................................................................ 110C/W Recommended Operating Conditions Ambient Operating Range (TA) .................................................................... -55C to +125C Positive Supply Voltage (V+) ........................................................................................... +15V Negative Supply Voltage (V-) ........................................................................................... -15V VAL (max) .......................................................................................................................... 0.8V VAH (min) .......................................................................................................................... 2.4V NOTE 1: Signals on S, D, or IN exceeding V+ or V- are clamped by internal diodes. Limit forward current to maximum current ratings. Stresses beyond those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. ---------------------------- Electrical Characteristics of DG441A/DG442A/883B 19-0093 Page 2 of Rev. C 6 TABLE 1. ELECTRICAL TESTS: TEST SWITCH Analog-Signal Range Drain-Source ON Resistance On-Resistance Match Between Channels 4/ On-Resistance Flatness 4/ DUAL SUPPLY Symbol CONDITIONS -55 C <=TA<= +125C V+=+15V, V-=-15V, GND=0V VAH=2.4V, VAL=0.8V Unless otherwise specified VANALOG NOTE 3 rDS(ON) rDS (ON) rFLAT (ON) Group A Subgroup Device type 1,2,3 All IS =-10mA, VD=8.5V, V+=13.5V, V-=-13.5V IS =-10mA, VD=10V, V+=15V, V-=-15V 1 2,3 1 2,3 All IS =-10mA, VD=5V or -5V, V+=15V, V-=-15V 1 2,3 All Limits Min 2/ -15 All Limits Max 2/ Units 15 V 85 100 4 5 9 15 Source- OFF Leakage Current IS(OFF) V+=16.5V, V-=-16.5V, VIN=2.4V VS=15.5V VD =15.5V 1 2,3 All -0.5 -20 0.5 20 nA Drain- OFF Leakage Current ID(OFF) V+=16.5V, V-=-16.5V, VS=15.5V VD =15.5V 1 2,3 All -0.5 -20 0.5 20 nA Channel-On Leakage Current ID(ON) + V+=16.5V, V-=-16.5V, VS=15.5V VD =15.5V 1 2,3 01 -0.5 -20 0.5 20 nA VIN=2.4V 1,2,3 All -500 500 nA VIN= 0.8V 1,2,3 All -500 500 nA 1,2,3 All 4.5 20 V 1,2,3 All 100 A 1 2,3 All -1 -5 1 5 A 1,2,3 All -100 IS(ON) INPUT Input Current/Voltage High Input Current/Voltage Low SUPPLY Power Supply Range Positive Supply Current IINH IINL I+ All channels on or off, V+=16.5V, V-=-16.5V, VIN=0 or 5V All channels on or off, V+=16.5V, V-=-16.5V, VIN=0 or 5V All channels on or off, V+=16.5V, V-=-16.5V, VIN=0 or 5V Negative Supply Current I- Ground Current IGND DYNAMIC Turn-On Time tON VS=10V, RL=1k, Figure 2 9 All 250 ns Turn-Off Time tOFF VD=10V, RL=1k, Figure 2 9 Q CL=1nF, VGEN=0V, RGEN=0, Figure 3 9 120 170 10 ns Charge Injection NOTE 2 01 02 All ---------------------------- Electrical Characteristics of DG441A/DG442A/883B 19-0093 Page 3 of A Rev. C 6 pC TABLE 1. ELECTRICAL TESTS: TEST SWITCH Analog-Signal Range Drain-Source ON Resistance SUPPLY Power Supply Range Positive Supply Current Negative Supply Current Ground Current DYNAMIC Turn-On Time Turn-Off Time Charge Injection SINGLE SUPPLY Symbol CONDITIONS -55 C <=TA<= +125C V+=+12V, V-=0V, GND=0V VAH=2.4V, VAL=0.8V Unless otherwise specified VANALOG NOTE 3 rDS(ON) IS =1.0mA, VD=3V or 8V, V+=10.8V I+ IGND All channels on or off, VIN=0 or 5V All channels on or off, VIN=0 or 5V All channels on or off, VIN=0 or 5V tON tOFF Q VS=8V, Figure 2 VS=8V, Figure 2 CL=1nF, VGEN=0V I- NOTE 3 Group A Subgroup Device type 1,2,3 All 1,3 2 All 1,2,3 All 1,2,3 All 1 2,3 1,2,3 All 9 9 9 All All Limits Min 2/ 0 10 Limits Max 2/ 12 V 160 200 30 V 100 A 1 5 A -1 -5 -100 A 400 200 10 All All Units ns ns pC NOTE 2: The algebraic convention, where the most negative value is a minimum and the most positive value a maximum, is used in this data sheet. NOTE 3: Guaranteed by design. NOTE 4: On-resistance match between channels and flatness is guaranteed only with bipolar-supply operation. Flatness is defined as the difference between the maximum and the minimum value of on-resistance as measured at the extremes of the specified analog range. TRUTH TABLE TERMINAL CONNECTION DG441A TERMINAL 01 01 02 02 LOGIC SWITCH NUMBER DG441A DG441A DG442A DG442A 0 ON J16 20LCC J16 20LCC 1 OFF 1 IN1 NC IN1 NC 2 D1 IN1 D1 IN1 3 S1 D1 S1 D1 4 VS1 VS1 LOGIC DG442A 5 GND VGND VSWITCH 0 OFF 6 S4 NC S4 NC 1 ON 7 D4 GND D4 GND 8 IN4 S4 IN4 S4 9 IN3 D4 IN3 D4 10 D3 IN4 D3 IN4 11 S3 NC S3 NC 12 NC IN3 NC IN3 13 V+ D3 V+ D3 14 S2 S3 S2 S3 15 D2 NC D2 NC 16 IN2 NC IN2 NC 17 V+ V+ 18 S2 S2 19 D2 D2 20 IN2 IN2 ---------------------------- Electrical Characteristics of DG441A/DG442A/883B 19-0093 Page 4 of Rev. C 6 Figure 2. Switching Time: See Commercial Data Sheet. Figure 3. Charge Injection: See Commercial Data Sheet. ORDERING INFORMATION: DG441AK/883B 16 CDIP DG441AZ/883B 20 LCC DG442AK/883B DG442AZ/883B 16 CDIP 20 LCC QUALITY ASSURANCE Sampling and inspection procedures shall be in accordance with MIL-Prf-38535, Appendix A as specified in MilStd-883. Screening shall be in accordance with Method 5004 of Mil-Std-883. Burn-in test Method 1015: 1. Test Condition, A, B, C, or D. 2. TA = +125C minimum. 3. Interim and final electrical test requirements shall be specified in Table 2. Quality conformance inspection shall be in accordance with Method 5005 of Mil-Std-883, including Groups A, B, C, and D inspection. Group A inspection: 1. Tests as specified in Table 2. 2. Selected subgroups in Table 1, Method 5005 of Mil-Std-883 shall be omitted. Group C and D inspections: a. End-point electrical parameters shall be specified in Table 1. b. Steady-state life test, Method 1005 of Mil-Std-883: 1. Test condition A, B, C, D. 2. TA = +125C, minimum. 3. Test duration, 1000 hours, except as permitted by Method 1005 of Mil-Std-883. TABLE 2. ELECTRICAL TEST REQUIREMENTS Mil-Std-883 Test Requirements Interim Electric Parameters Method 5004 Final Electrical Parameters Method 5005 Group A Test Requirements Method 5005 Group C and D End-Point Electrical Parameters Method 5005 * Subgroups per Method 5005, Table 1 1 1*, 2, 3, 9 1, 2, 3, 9 1 PDA applies to Subgroup 1 only. ---------------------------- Electrical Characteristics of DG441A/DG442A/883B 19-0093 Page 5 of Rev. C 6