T3DSO1000/T3DSO1000A Data Sheet Oscilloscopes Debug with Confidence 100 MHz - 350 MHz Tools for Improved Debugging Long Capture - Up to 28Mpts interleaved. Capture more time and show more waveform detail. Math and Measure - 7 basic math functions plus FFT and 38 automatic measurement parameters. Extract results from waveforms and measurements. Connectivity - USB for mass storage, printing and PC control, plus LAN for fast data transfer. Save data for external analysis and screen images for reports. Serial Bus Trigger and Decode - I2C, SPI, UART, RS232, CAN, LIN. Debug serial buses directly in your Oscilloscope. Waveform Sequence Recorder - record and play back up to 80,000 waveforms. Replay the changing waveform history. Optional MSO - 16 Digital Channels (4 channel and A series only). Add mixed signal debugging to your Oscilloscope. Key Specifications Bandwidth 100 MHz, 200, 350 MHz Channels 2 or 4 Memory up to 14 Mpts/Ch (28 Mpts interleaved) Sample Rate up to 1 GS/s / 2 GS/s interleaved Display 7" Bright TFT LCD (800 x 480) Connectivity USB Host, USB Device, LAN PRODUCT OVERVIEW T3DSO1102: T3DSO1104: T3DSO1202A: T3DSO1204: T3DSO1302A: 2 Channel 100 MHz 4 Channel 100 MHz 2 Channel 200 MHz 4 Channel 200 MHz 2 Channel 350 MHz Teledyne Test Tools new T3DSO1000 Oscilloscopes feature two channel and four channel models. The two channel models are available with 100 MHz, 200 MHz and 350 MHz analog bandwidths, a single ADC with up to 2 GSa/s maximum sample rate, and memory up to 28 Mpts. The four channel scope is available in 100 and 200 MHz models and incorporates two 1 GSa/s ADCs and two 14 Mpts memory modules. When all channels are enabled, each channel has sample rate of 500 MSa/s, or 1 GS/s for the A series, and a standard record length of 7 Mpts, or 14 Mpts for the A Series. When only a single channel per ADC is active, the maximum sample rate and the maximum record length are doubled. For ease-of-use, the most commonly used functions can be accessed with its user-friendly front panel design. The T3DSO1000 series employs a new generation of high speed display technology that provides excellent signal clarity, fidelity and performance. The system noise floor is also lower than similar products in the industry. It comes with a minimum vertical input range of 500 uV/div, an innovative digital trigger system with high sensitivity and low jitter, and a waveform capture rate of 400,000 frames/ sec (sequence mode). The T3DSO1000 also employs a256-level intensity grading display function and a color temperature display mode not found in other models in this class. Teledyne Test Tools latest oscilloscope offering supports multiple powerful triggering modes including serial bus triggering. Serial bus decoding for IIC, SPI, UART, CAN, LIN bus types is included. The models also include History waveform recording, and sequential triggering that enable extended waveform recording and analysis. Key Features 100 MHz, 200 MHz and 350 MHz bandwidth models Two channel series have one ADC, four channel series have two ADCs. When all channels are enabled, each channel has a maximum sample rate of 500 MSa/s (1 Gsa/s for the A series). When a single channel per ADC is active, it has sample rate of 1 GSa/s (2 Gsa/s for the A Series) The newest generation of high speed display technology Waveform capture rate up to 100,000 wfm/s (normal mode), and 400,000 wfm/s (sequence mode) Supports 256-level intensity grading and color display modes Record length up to 28 Mpts Digital trigger system Another powerful addition is the new 1millionpoint FFT math function that gives the T3DSO1000 very high frequency resolution when observing signal spectra. The new digital design also includes a hardware co-processor that delivers measurements quickly and accurately without slowing acquisition and front-panel response. The features and performance of Teledyne Test Tools T3DSO1000 family cannot be matched in this price class. The four channel and A series includes even more functions, including: searching and navigating, on-screen Bode plot, 16 digital channels (Option), an external USB powered 25MHz AWG module (Option), a USB WIFI adapter (Option), and an embedded application that allows remote control via web browser. 2 Intelligent trigger: Edge, Slope, Pulse Width, Window, Runt, Interval, Time out (Dropout), Pattern Serial bus triggering and decoding (Standard), supports protocols IIC, SPI, UART, RS232, CAN, LIN Video trigger, supports HDTV Low background noise with voltage scales from 500V/div to 10 V/div 10 types of one-button shortcuts, supports Auto Setup, Default, Cursors, Measure, Roll, History, Display/Persist, Clear Sweep, Zoom and Print Segmented acquisition (Sequence) mode, divides the maximum record length into multiple segments (up to 80,000), according to trigger conditions set by the user, with a very small dead time segment to capture the qualifying event. History waveform record (History) function, maximum recorded waveform length is 80,000 frames. Models and key Specification Model T3DSO1102 T3DSO1104 T3DSO1204 T3DSO1202A T3DSO1302A Bandwidth 100 MHz 200 MHz 200 MHz 350 MHz SamplingRate (Max.) Two channel series have a single 1 GSa/s ADC, four channel series have two 1 GSa/s ADCs. When all channels are enabled, each channel has a maximum sample rate of 500 MSa/s. When a single channel per pair is active, that channel has sample rate of 1GSa/s Channels 4, no EXT (T3DSO1104 and T3DSO1204 four channel series) 2+EXT (T3DSO1102, T3DSO1202A and T3DSO1302A two channel series) Memory Depth (Max.) 7 Mpts/CH (not interleave mode); 14 Mpts/CH (interleave mode) Waveform Capture Rate (Max.) 100,000 wfm/s (normal mode), 400,000 wfm/s (sequence mode) Trigger Type Edge, Slope, Pulse Width, Window, Runt, Interval, Dropout, Pattern, Video Serial Trigger and decoder (Standard) IIC, SPI, UART/RS232, CAN, LIN 16 Digital Channels (Option not available on the T3DSO1102) Maximum waveform capture rate up to 1 GSa/s, Record length up to 14 Mpts/CH USB AWG module (Option not available on the T3DSO1102) One channel, 25 MHz, sample rate of 125 MHz, wave length of 16 kpts Bode plot (Not available on the T3DSO1102) Minimum start frequency of 10 Hz, minimum scan bandwidth of 500 Hz, maximum scan bandwidth of 120 MHz (dependent on Oscilloscope and AWG bandwidth), 500maximum scan frequency points USB WIFI adapter (Option not available on the T3DSO1102) 802.11b/g/b, WPA-PSK, the adapter must be purchased separately by the scope user (TP-Link TL-WN725N) I/O USB Host, USB Device, LAN, Pass/Fail, Trigger Out, Sbus (Teledyne Test Tools MSO) Probe (Std) 2/4 pcs passive probe Display 7 inch TFT-LCD (800 x 480) Weight All models except T3DSO1102: Without package 2.6 Kg; With package 3.8 Kg T3DSO1102: Without package 2.5 Kg; With package 3.5 Kg Automatic measurement function for 38 parameters as well as Measurement Statistics, Zoom, Gating, Math, History and Reference functions 1 Mpts FFT Math and measurement functions use all sampled data points (up to 28 Mpts) USB AWG module1) USB WIFI adapter1) Web Browser based control1) Large 7 inch TFT-LCD display with 800 * 480 resolution Preset key can be customized for user settings or factory "defaults" High Speed hardware based Pass/ Fail function MSO, 16 digital channels1) Bode plot1) 2 pcs passive probe Search and navigate1) Security Erase mode 14 Mpts/CH (not interleave mode); 28 Mpts/CH (interleave mode) Math functions (FFT, addition, subtraction, multiplication,division, integration, differential, square root) The A series has a single 2 GSa/s ADC. When both channels are enabled, each channel has a maximum sample rate of 1 GSa/s. When a single channel is active, that channel has sample rate of 2 GSa/s 1) Multiple interface types: USB Host, USB Device (USB-TMC), LAN, Trigger Out Supports SCPI remote control commands Supports Multi-language display and embedded online help Not available on the T3DSO1102. 3 FUNCTION & CHARACTERISTICS 7 inch TFT-LCD display and 10 one-button menus When all channels are enabled, each channel has a maximum sample rate of up to 1 GSa/s (depending on the model) When a single channel per pair is active, that channel has sample rate of up to 2 GSa/s (depending on the model) Front panel of T3DSO1104, T3DSO1202A, T3DSO1204, T3DSO1302A Front panel of T3DSO1102 7-inch TFT-LCD display with 800 * 480 resolution Most commonly used functions are accessible using 10different one-button operation keys: Auto Setup, Default, Cursor, Measure, Roll, History, Persist, Clear Sweep, Zoom, Print Record Length of Up to 28 Mpts depending on model and channels (single channel/pair mode). Using hardware-based Zoom technologies and max record length of up to 28 Mpts, users are able to over-sample to capture longer time periods at higher resolution and use the zoom feature to see more details within each signal. 4 The four channel series has two 1 GSa/s ADC chips (channel 1 and 2 share one, channel 3 and 4 share another), so that each channel can achieve sample rates up to 500 MSa/s and work on bandwidths of 200 MHz when all channels are enabled. Waveform Capture Rate Up to 400,000 wfm/s With a waveform capture rate of up to 400,000 wfm/s (sequence mode), the oscilloscope can easily capture the unusual or low-probability events. 256-Level Intensity Grading and Color Temperature Display History Waveforms (History) Mode and Segmented Acquisition (Sequence) New display technology provides for fast refresh rates. The resulting intensity-graded trace is brighter for events that occur with more frequency and dims when the events occur with less frequency. Playback the latest triggered events using the history function. Segmented memory collection will store trigger events into multiple (Up to 80,000) memory segments, each segment will store triggered waveforms and timestamp each frame. True measurement to 14 M points or 28 M points depending on the model The color temperature display is similar to the intensitygraded trace function, but the trace occurrence is represented by different colors (color "temperature") as opposed to changes in the intensity of one color. Red colors represents the more frequent events, while blue is used to mark points that occur lest frequently. At any one timebase, T3DSO1000 can measure using all acquired sample points. This ensures the accuracy of measurements while the math coprocessor decreases measurement time and increases ease-of-use. Serial Bus Decoding Function (Standard) Gate and Zoom Measurement T3DSO1000 displays the decoding through the events list. Bus protocol information can be quickly and intuitively displayed in a tabular format. Through Gate and Zoom measurement, the user can specify an arbitrary interval of waveform data analysis and statistics. This helps avoid measurement errors that can be caused by invalid or extraneous data, greatly enhancing the measurements' validity and flexibility. 5 FUNCTION & CHARACTERISTICS 1 M points FFT 16 Digital Channels/MSO (Option not available on the T3DSO1102) The math co-processor enables FFT analysis of incoming signals using up to 1 M samples per waveform. This provides high frequency resolution with a fast refresh rate. The FFT function also supports a variety of window functions so that it can adapt to different spectrum measurement needs. 16 digital channels enables users to acquire and trigger on the waveforms then analyze the pattern, simultaneously with one instrument. Color coded logic levels clearly differentiate high and low states. Hardware-Based High Speed Pass/Fail function Search and Navigate (not available on the T3DSO1102) The T3DSO1000 utilizes a hardware-based Pass/Fail function, performing up to 40,000 Pass/Fail decisions each second. Easily generate user defined test templates provide trace mask comparison making it suitable for long-term signal monitoring or automated production line testing. Customizable Default Key The T3DSO1000 series can search events specified by the user in a frame. It can also navigate by time (delay position) and historical frames. Search and Navigate is not available on the T3DSO1102. The current parameters of the oscilloscope can be preset to Default Key through the Save menu. 6 Bode Plot (not available on the T3DSO1102) USB 25 MHz AWG Module (Option not available on the T3DSO1102) The T3DSO1000 series supports an optional USB 25 MHz function/arbitrary waveform generator that is operated from the USB host connection. Functions include Sine, Square, Ramp, Pulse, Noise, DC and 45 built-in waveforms. The arbitrary waveforms can be accessed and edited by the Teledyne Test Tools PC software. Option not available for the T3DSO1102. Complete Connectivity T3DSO1000 can control the USB AWG module, control an independent Teledyne Test Tools T3AFG instrument, scan an object's amplitude and phase frequency response, and display the data as a Bode Plot. It can also show the result lists, and export the data to a USB disk. Not available for the T3DSO1102. USB WiFi Adapter (Option not available on the T3DSO1102) Back panel of T3DSO1104, T3DSO1202A, T3DSO1204, T3DSO1302A Back panel of T3DSO1102 T3DSO1000 supports USB Host, USB Device (USB-TMC), LAN(VXI-11), Pass/Fail and Trigger Out. Web control (not available on the T3DSO1102) USB WiFi Adapter WiFi control of instrumentation can provide a convenient and safe method of configuring and collecting data. This new feature works with a Teledyne Test Tools approved WiFi adapter to provide wireless control and communications with Teledyne Test Tools 4 channel scopes. Option not available for the T3DSO1102. The approved adapter is the TP-Link TL-WN725N (not supplied). With the new embedded web server, users can control the Oscilloscopes from a simple web page. This provides remote troubleshooting and monitoring capabilities. 7 SPECIFICATIONS Model T3DSO1102, T3DSO1104, T3DSO1204 T3DSO1202A, T3DSO1302A 1 GSa/s (single channel/pair), 500 MSa/s (two channels/pair) Max 14 Mpts/Ch (single channel/pair), 7 Mpts/Ch (two channels/pair) 2 nsec (Four channel series) 4 nsec (Two channel series) Averages: 4, 16, 32, 64, 128, 256, 512, 1024 Enhance bits: 0.5, 1.5, 2, 2.5, 3; Selectable Sin(x)/x, Linear 2 GSa/s (single channel), 1 GSa/s (two channels) Max 28 Mpts/Ch (single channel), 14 Mpts/Ch (two channels) 1 nsec 2+EXT Max.Input voltage 4, no EXT (four channel series) 2+EXT (two channel series) DC, AC, GND DC: (1 M 2%) || (15 pF 2 pF) (Four channel series) DC: (1 M 2%) || (18 pF 2 pF) (Two channel series) 1 M 400 Vpk (DC + Peak AC <= 10 kHz) CH to CH Isolation Probe attenuation DC-Max BW > 40 dB 0.1X, 0.2X, 0.5X, 1X, 2X, 5X, 10X......1000X, 2000X, 5000X, 10000X Acquire System Sampling Rate Memory Depth Peak Detect Average Eres Waveform interpolation Input Channels Coupling Impedance DC: (1 M 2%) || (18 pF 2 pF) DC: (50 2%) 1 M 400 Vpk (DC + Peak AC <= 10 kHz) DC: 50 : < 5V rms Vertical System Bandwidth (-3 dB ) Vertical Resolution Vertical Scale (Probe 1X) Offset Range (Probe 1X) Bandwidth Limit Bandwidth Flatness Low Frequency Response (AC - 3 dB) Noise SFDR including harmonics DC Gain Accuracy Offset Accuracy Risetime Overshoot (500 ps Pulse) 200 MHz (T3DSO1204) / T3DSO1202A) 350 MHz (T3DSO1302A) 100 MHz (T3DSO1102 / T3DSO1104) 8-bit 500 V/div - 10 V/div (1-2-5 sequence ) 500 V - 118 mV: 2 V 500 V - 100 mV: 2 V 120 mV - 1.18 V: 20 V 102 mV - 1 V: 20 V 1.2 V - 10 V: 200 V 1.02 V - 10 V: 200 V 20 MHz 40% 20 MHz 40% DC - 10% (BW): 1 dB DC - 60% (BW): 1 dB 10% - 50% (BW): 2 dB 60% - 100% (BW): + 1 dB/-3 dB 50% - 100% (BW): + 2 dB/-3 dB 10 Hz (at input BNC) 2 Hz (at input BNC) ST-DEV 0.5 division (< 1 mV/div) ST-DEV 0.2 division (< 2 mV/div) ST-DEV 0.1 division ( 2 mV/div) 35 dB 3.0%: 5 mV/div-10 V/div 4.0%: 2 mV/div (1% * Offset + 1.5% * 8 * div + 2 mV): 2 mV/div (1% * Offset + 1.5% * 8 * div + 500 uV): 1 mv/div Typical 1.0 ns (T3DSO1302A) Typical 1.8 ns (T3DSO1202A / T3DSO1204) Typical 3.5 ns (T3DSO1102 / T3DSO1104) < 10% Horizontal System Timebase Scale Channel Skew Waveform Capture Rate Intensity grading Display Format Timebase Accuracy Roll Mode 8 1.0 ns/div - 100 s/div 500 ps/div - 100 s/div < 100 ps Up to 100,000 wfm/s (normal mode), 400,000 wfm/s (sequence mode) 256 Levels Y-T, X-Y, Roll 25 ppm 50 ms/div - 100 s/div (1-2-5 step) Model T3DSO1102, T3DSO1104, T3DSO1204 T3DSO1202A, T3DSO1302A Trigger System Trigger Mode Trigger Level Holdoff Range Trigger Coupling Coupling Frequency Response Coupling Frequency Response (EXT) Trigger Accuracy (Typical) Trigger Sensitivity Trigger Jitter Trigger Displacement Auto, Normal, Single Internal: 4.5 div from the center of the screen EXT: 0.6 V (Two channel series) EXT/5: 3 V (Two channel series) 80 ns - 1.5 s AC DC LFRJ HFRJ Noise RJ DC: Passes all components of the signal AC: Blocks DC components and attenuates signals below 8 Hz LFRJ: Blocks the DC component and attenuates the low-frequency components below 2 MHz HFRJ: Attenuates the high-frequency components above 1.2 MHz DC: Passes all components of the signal DC: Passes all components of the signal AC: Blocks DC components and attenuates AC: Blocks DC components and attenuates signals below 20 Hz signals below 10 Hz LFRJ: Blocks the DC component and LFRJ: Blocks the DCcomponent and attenuates the low-frequency components attenuates the low-frequency components below 7 KHz below 6 KHz HFRJ: Attenuates the high-frequency HFRJ: Attenuates the high-frequency components above 160 KHz components above 200 KHz Internal: 0.2 div EXT (Two channel series): 0.4 div DC - Max BW 0.6 div EXT (Two channel series): 200 mVpp DC - 10 MHz 300 mVpp 10 MHz - BW frequency EXT/5 (Two channel series): 1 Vpp DC - 10 MHz 1.5 Vpp 10 MHz - BW frequency < 100 ps Pre-Trigger: 0 - 100% Memory Delay Trigger: 0 to 10,000 div Edge Trigger Slope Source Rising, Falling, Rising & Falling All channels/ EXT/ (EXT/5)/ AC Line (Two channel series) All channels/ AC Line (Four channel series) Slope Trigger Slope LimitRange Source TimeRange Resolution Rising, Falling <,>,<>,>< All channels 2 ns - 4.2 s 1 ns Pulse Trigger Polarity Limit Range Source Pulse Range Resolution +wid , -wid <,>,<>,>< All channels 2 ns ~ 4.2 s 1 ns Video Trigger Signal Standard Source Sync Trigger condition NTSC, PAL, 720p/50, 720p/60, 1080p/50, 1080p/60, 1080i/50, 1080i/60, Custom All channels Any, Select Line, Field 9 SPECIFICATIONS Window Trigger Window Type Source Absolute, Relative All channels Interval Trigger Slope Limit Range Source Time Range Resolution Rising, Falling <,>,<>,>< All channels 2 ns ~ 4.2 s 1 ns Dropout Trigger Timeout Type Source Slope Time Range Resolution Edge, State All channels Rising, Falling 2 ns ~ 4.2 s 1 ns Runt Trigger Polarity Limit Range Source Time Range Resolution +wid , -wid <,>,<>,>< All channels 2 ns ~ 4.2 s 1 ns Pattern Trigger Pattern Setting Logic Source Limit Range Time Range Resolution Invalid, Low, High AND, OR, NAND, NOR All channels <,>,<>,>< 2 ns ~ 4.2 s 1 ns Serial Trigger I2C Trigger Condition Source (SDA/SCL) Data format Limit Range Data Length R/W bit SPI Trigger Condition Source (CS/CL/Data) Data format Data Length Bit Value Bit Order 10 Start, Stop, Restart, No Ack, EEPROM, 7 bits Address & Data, 10 bits Address & Data, Data Length All channels Hex EEPROM: =, >, < EEPROM: 1 byte Addr & Data: 1 ~ 2 byte Data Length: 1 ~ 12 byte Addr & Data: Read, Write, Don't care Data All channels Binary 4 ~ 96 bit 0, 1, X LSB, MSB UART/RS232 Trigger Condition Source (RX/TX) Data format Limit Range Data Length Data Width Parity Check Stop Bit Idle Level Baud (Selectable) (Custom) CAN Trigger Condition Source ID Data Format Data Length Baud Rate (Selectable) LIN Trigger Condition Source ID Data Format Data Length Baud Rate (Selectable) Baud Rate (Custom) Start, Stop, Data, Parity Error All channels Hex =, >, < 1 byte 5 bit, 6 bit, 7 bit, 8 bit None, Odd, Even 1 bit, 1.5 bit, 2 bit High, Low 600/1200/2400/4800/9600/19200/38400/57600/115200 bit/s 300 bit/s ~ 5,000,000 bit/s Start, Remote, ID, ID + Data, Error All channels STD (11 bit), EXT (29 bit) Hex 1~2 byte 5 k/10 k/20 k/50 k/100 k/125 k/250 k/500 k/800 k/1 M bit/s Break, Frame ID, ID+Data, Error All channels 1 byte Hex 1 ~ 2 byte 600/1200/2400/4800/9600/19200 bit/s 300 bit/s ~ 20 kbit/s Serial Decoder I2C Decoder Signal Address Threshold List SPI Decoder Signal Edge Select Idle Level Bit Order Threshold List UART/RS232 Decoder Signal Data Width Parity Check Stop Bit Idle Level Threshold List CAN Decoder Signal Source Threshold List LIN Decoder LIN Specification Package Revision Threshold List SCL, SDA 7 bits, 10 bits -4.5 ~ 4.5 div 1 ~ 7 lines SCL,MISO, MOSI, CS * NOTE 2 channel scopes can only use 2 signal identifiers Rising, Falling Low, High MSB, LSB -4.5 ~ 4.5 div 1 ~ 7 lines RX, TX 5 bit, 6 bit, 7 bit, 8 bit None, Odd, Even 1 bit, 1.5 bit, 2 bit Low, High -4.5 ~ 4.5 div 1 ~ 7 lines CAN_H, CAN_L CAN_H, CAN_L, CAN_H-CAN_L -4.5 ~ 4.5 div 1 ~ 7 lines Ver1.3, Ver2.0 -4.5 ~ 4.5 div 1 ~ 7 lines 11 SPECIFICATIONS Measurement Source Number of Measurements Measurement Range Measurement Parameters (38 Types) Vertical (Voltage) Horizontal( Time) Delay Cursors Statistics Counter 12 All channels, All channels in Zoom, Math, All References, History Display 5 measurements at the same time Screen region, Gate region Max Highest value in input waveform Min Lowest value in input waveform Pk-Pk Difference between maximum and minimum data values Ampl Difference between top and base in a bimodal signal, or between max and min in an unimodal signal Top Value of most probable higher state in a bimodal waveform Base Value of most probable lower state in a bimodal waveform Mean Average of all data values Cmean Average of data values in the first cycle Stdev Standard deviation of all data values Cstd Standard deviation of all data values in the first cycle VRMS Root mean square of all data values Crms Root mean square of all data values in the first cycle FOV Overshoot after a falling edge; (base-min)/Amplitude FPRE Overshoot before a falling edge; (max-top)/Amplitude ROV Overshoot after a rising edge; (max-top)/Amplitude RPRE Overshoot before a rising edge; (base-min)/Amplitude Level@X the voltage value of the trigger point Period Period for every cycle in waveform at the 50% level, and positive slope Freq Frequency for every cycle in waveform at the 50% level, and positive slope +Wid Width measured at 50% level and positive slope -Wid Width measured at 50% level and negative slope Rise Time Duration of rising edge from 10-90% Fall Time Duration of falling edge from 90-10% Bwid Time from the first rising edge to the last falling edge, or the first falling edge to the last rising edge at the 50% crossing +Dut Ratio of positive width to period -Dut Ratio of negative width to period Delay Time from the trigger to the first transition at the 50% crossing Time@LevelTime from the trigger to each rising edge at the 50% crossing. When Statistics is Off, it shows the time from the trigger to the last rising edge at the 50% crossing. When Statistics is On, it shows the Current, Mean, Min, Max, Standard Deviation of time from the trigger to each rising edge at the 50% crossing in multiple frames (number = Count). Phase Calculate the phase difference between two edges FRR Time between the first rising edges of the two channels FRF Time from the first rising edge of channel A to the first falling edge of channel B FFR Time from the first falling edge of channel A to the first rising edge of channel B FFF Time from the first falling edge of channel A to the first falling edge of channel B LRR Time from the first rising edge of channel A to the last rising edge of channel B LRF Time from the first rising edge of channel A to the last falling edge of channel B LFR Time from the first falling edge of channel A to the last rising edge of channel B LFF Time from the first falling edge of channel A to the last falling edge of channel B Skew Time of source A edge minus time of nearest source B edge Manual : Time X1, X2, (X1-X2), (1/T) Voltage Y1, Y2, (Y1-Y2) Track: Time X1, X2, (X1-X2) Current, Mean, Min, Max, Stdev, Count Hardware 6 bit counter( channels are selectable) Math Function Operation FFT window FFT display Number of Decoders + , - , * , / , FFT , d/dt , dt , Rectangular, Blackman, Hanning, Hamming, Flattop Full Screen, Split, Exclusive 2 USB AWG Module (Not available on the T3DSO1102) Channel Max. Output Frequency Sampling Rate Frequency Resolution Frequency Accuracy Vertical Resolution AmplitudeRange Waveform Type Output impedance Protection 1 25 MHz 125 MSa/s 1 Hz 50 ppm 14-bits -1.5 ~ +1.5 V (50 ) -3 ~ +3 V (High-Z) Sine, Square, Ramp, pulse, Noise, DC and 45 built-in waveforms 50 2% Over-Voltage Protection, Current-Limiting Protection Sine Frequency Offset Accuracy (10 kHz) Amplitude flatness (10 kHz, 5 Vpp) SFDR HD 1 Hz ~ 25 MHz (1% * Offset Setting Value + 1 mVpp) 0.3 dB DC ~ 1 MHz -60 dBc 1 MHz ~ 5 MHz -55 dBc 5 MHz ~ 25 MHz -50 dBc DC ~ 5 MHz -50 dBc 5 MHz ~ 25 MHz -45 dBc Square/Pulse Frequency Duty Cycle Rise/Fall time Overshoot (1 kHz,1 Vpp, Typical) Pulse Width Jitter 1 Hz ~ 10 MHz 1% ~ 99% < 24 ns (10% ~ 90%) < 3% (typical 1 kHz, 1 Vpp) > 50 ns < 500 ps + 10 ppm Ramp Frequency Linearity (Typical) Symmetry 1 Hz ~ 300 kHz < 0.1% of Pk-Pk (Typical, 1 kHz, 1 Vpp, 100% Symmetry) 0% ~ 100% (Adjustable) DC Offset range Accuracy 1.5 V (50 ) 3 V (High-Z) (|offset| * 1% + 3 mV) Noise Bandwidth > 25 MHz (-3 dB) Arbitrary Wave Frequency Wave Length Sampling Rate Waveform Entry 1 Hz ~ 5 MHz 16 kpts 125 MSa/s EasyScope and USB-Stick 13 SPECIFICATIONS Digital Channels (Not available on the T3DSO1102) No. of Channels Max. Sampling Rate Memory Depth Min. Detectable Pulse Width Level Group Level Range Logic Type Skew[2] 16 1 GSa/s 14 Mpts/CH 4 ns D0~D7, D8~D15 -8 V ~ 8 V TTL, CMOS, LVCMOS3.3, LVCMOS2.5, custom D0~D15: 1 sampling interval Analog To Digital: (1 sampling interval +1 ns) I/O Standard Pass/Fail USB Host, USB Device, LAN, Pass/Fail, Trigger Out 3.3 V TTL Output Display (Screen) Display Type Display Resolution Display Color Contrast (Typical) Backlight Range 7-inch TFT LCD 800 x 480 24 bit 500:1 300 nit 8 x 14 divisions Display (Waveform) Display Mode Persist Time Color Display Screen Saver Language Dot, Vector Off, 1 Sec, 5 Sec, 10 Sec, 30 Sec, Infinite Normal, Color 1 min, 5 min, 10 min, 30 min, 1 hour, Off Simplified Chinese, Traditional Chinese, English, French, Japanese, Korean, German, Russian, Italian, Portuguese Environments Temperature Humidity Height Electromagnetic Compatibility Safety Operating: 10 ~ +40 Non-operating: -20 ~ +60 Operating: 85% RH, 40 Deg C, 24 hours Non-operating: 85% RH, 65 Deg C, 24 hours Operating: 3000 m Non-operating: 15,266 m 2004/108/EC) Execution Standard EN 61326-1:2006 EN 61000-3-2:2006 + A2:2009, EN 61000-3-3:2008 2006/95/EC Execution Standard EN 61010-1:2010 / EN 61010-2-030:2010 Power Supply Input Voltage Frequency Power 100 ~ 240 VAC, CAT II, Auto selection 50/60/400 Hz 50 W Max Mechanical (T3DSO1104, T3DSO1204, T3DSO1202A, T3DSO1302A) Dimensions Weight Length: 312 mm / Width: 132.6 mm / Height: 151 mm N.W: 2.6 kg; G.W: 3.8 kg Mechanical (T3DSO1102) Dimensions Weight Length: 312 mm / Width: 134 mm / Height: 150 mm N.W: 2.5 Kg; G.W: 3.5 Kg All T3DSO1000 Series Oscilloscopes come with a 3 year return to Teledyne LeCroy warranty. 14 Probes and Accessories Probe Model Passive Probes (T3DSO1102, T3DSO1104, T3DSO1202A, T3DSO1204) T3PP300 Picture Passive Probe, Bandwidth: 300 MHz Description Passive Probes (T3DSO1302A) T3PP350 Passive Probe, Bandwidth: 350 MHz USB AWG Module T3DSO1000FGMOD Output Sine, Square, Ramp, pulse, Noise, DC and 45 built-in waveforms. The arbitrary waveforms can be accessed and edited by the EasyScope PC software Ordering information Product Name Standard Accessories Optional Accessories T3DSO1102 100 MHz Two Channels T3DSO1104 100 MHz Four Channels T3DSO1202A 200 MHz Two Channels T3DSO1204 200 MHz Four Channels T3DSO1302A 350 MHz Two Channels USB Cable -1 Quick Start -1 Passive Probe -4 / 2 Certification -1 Power Cord -1 16 Channel MSO Software (Not available for T3DSO1102) 16 Channel Logic Analyzer Lead (Not available for T3DSO1102) AWG Software (Not available for T3DSO1102) USB AWG Module Hardware (Not available for T3DSO1102) WIFI Software (Not available for T3DSO1102) Does not include the TP-Link TL-WN725N, see below T3DSO1000-MSO or T3DSO1000A-MSO T3DSO1000-LS (Requires T3DSO1000-MSO or T3DSO1000A-MSO Software) T3DSO1000-FG or T3DSO1000A-FG T3DSO1000-FGMOD (Requires T3DSO1000-FG or T3DSO1000A-FG) T3DSO1000-WIFI or T3DSO1000A-WIFI For Wi-Fi support the T3DSO1000-WIFI/T3DSO1000A-WIFI option is required and the TP-Link TL-WN725N. The TP-Link TL-WN725N is NOT supplied as part of the T3DSO1000-WIFI/T3DSO1000A-WIFI option. The TP-Link TL-WN725N is not available through Teledyne Test Tools and should be purchased separately. 15 ABOUT TELEDYNE TEST TOOLS Company Profile Teledyne LeCroy is aleading provider of oscilloscopes, protocol analyzers and related test and measurement solutions that enable companies across awide range of industries to design and test electronic devices of all types. Since our founding in 1964, we have focused on creating products that improve productivity by helping engineers resolve design issues faster and more effectively. Oscilloscopes are tools used by designers and engineers to measure and analyze complex electronic signals in order to develop high-performance systems and to validate electronic designs in order to improve time to market. The Teledyne Test Tools brand extends the Teledyne LeCroy product portfolio with a comprehensive range of test equipment solutions. This new range of products delivers a broad range of quality test solutions that enable engineers to rapidly validate product and design and reduce time-tomarket. Designers, engineers and educators rely on Teledyne Test Tools solutions to meet their most challenging needs for testing, education and electronics validation. Location and Facilities Headquartered in Chestnut Ridge, New York, Teledyne Test Tools and Teledyne LeCroy has sales, service and development subsidiaries in the US and throughout Europe and Asia. Teledyne Test Tools and Teledyne LeCroy products are employed across awide variety of industries, including semiconductor, computer, consumer electronics, education, military/aerospace, automotive/industrial, and telecommunications. Distributed by: Teledyne LeCroy (US Headquarters) 700 Chestnut Ridge Road Chestnut Ridge, NY. USA 10977-6499 Phone: Fax Sales: Phone Support: Email Sales: Email Support: Web Site: 800-553-2769 or 845-425-2000 845-578-5985 1-800-553-2769 contact.corp@teledynelecroy.com support@teledynelecroy.com http://teledynelecroy.com/ World wide support contacts can be found at: https://teledynelecroy.com/support/contact World wide instrument service can be found at: https://teledynelecroy.com/support/service.aspx RoHS and WEEE information can be found at: https://teledynelecroy.com/support/rohs.aspx Teledyne LeCroy (European Headquarters) Teledyne LeCroy GmbH Im Breitspiel 11c D-69126 Heidelberg, Germany Phone: Fax: Phone Service: Phone Support: Email Sales: Email Service: Email Support: Web Site: +49 6221 82700 +49 6221 834655 +49 6221 8270 85 +49 6221 8270 28 contact.gmbh@teledynelecroy.com service.gmbh@teledynelecroy.com tlc.t3.appsupport.eu@teledyne.com http://teledynelecroy.com/ teledynelecroy.com (c) 2019 Teledyne Test Tools is a brand and trademark of Teledyne LeCroy Inc. All rights reserved. Specifications, prices, availability and delivery subject to change without notice. Product brand or brand names are trademarks or requested trademarks of their respective holders. T3 stands for Teledyne Test Tools. 23sept19