INFRARED EMITTING DIODE Part Number: AM2520F3C03 Features Description z Subminiature package. F3 Made with Gallium Arsenide Infrared Emitting diodes. z Mechanically and spectrally matched to the phototransistor. z Gull wing lead. z Long life - solid state reliability. z Low package profile. z Package : 1000pcs / reel. z Moisture sensitivity level : level 3. z RoHS compliant. Package Dimensions Notes: 1. All dimensions are in millimeters (inches). 2. Tolerance is 0.25(0.01") unless otherwise noted. 3. Lead spacing is measured where the leads emerge from the package. 4. The specifications, characteristics and technical data described in the datasheet are subject to change without prior notice. 5. The device has a single mounting surface. The device must be mounted according to the specifications. SPEC NO: DSAM8514 REV NO: V.2 DATE: FEB/02/2013 PAGE: 1 OF 6 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: Y.Liu ERP: 1202000467 Selection Guide Part No. AM2520F3C03 Dice F3 (GaAs) Viewing Angle [1] Po (mW/sr) [2] @ 20mA Lens Type Water Clear Code. Min. Max. C 5 8 D 8 12 E 12 20 21/2 20 Notes: 1. 1/2 is the angle from optical centerline where the luminous intensity is 1/2 of the optical peak value. 2. Radiant Intensity/ luminous flux: +/-15%. Electrical / Optical Characteristics at TA=25C Parameter P/N Symbol Min. Typ. Max. Units Test Conditions Forward Voltage [1] F3 VF 1.0 1.2 1.6 V IF=20mA Reverse Current F3 IR 10 uA VR = 5V Capacitance F3 C pF VF=0V;f=1MHz Peak Spectral Wavelength F3 P nm IF=20mA Spectral Bandwidth F3 1/2 nm IF=20mA 90 920 960 50 Note: 1. Forward Voltage: +/-0.1V. Absolute Maximum Ratings at TA=25C Parameter Symbol F3 Units Power dissipation PD 80 mW DC Forward Current IF 50 mA Peak Forward Current [1] iFS 1.2 A Reverse Voltage VR 5 V Operating Temperature TA -40 To +85 C TSTG -40 To +85 C Storage Temperature Note: 1. 1/100 Duty Cycle, 10s Pulse Width. SPEC NO: DSAM8514 REV NO: V.2 DATE: FEB/02/2013 PAGE: 2 OF 6 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: Y.Liu ERP: 1202000467 AM2520F3C03 SPEC NO: DSAM8514 REV NO: V.2 DATE: FEB/02/2013 PAGE: 3 OF 6 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: Y.Liu ERP: 1202000467 AM2520F3C03 Reflow soldering is recommended and the soldering profile is shown below. Other soldering methods are not recommended as they might cause damage to the product. Recommended Soldering Pattern (Units : mm; Tolerance: 0.1) Reel Dimension Tape Specifications (Units : mm) SPEC NO: DSAM8514 REV NO: V.2 DATE: FEB/02/2013 PAGE: 4 OF 6 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: Y.Liu ERP: 1202000467 PACKING & LABEL SPECIFICATIONS AM2520F3C03 All design applications should refer to Kingbright application notes available at http://www.KingbrightUSA.com/ApplicationNotes SPEC NO: DSAM8514 REV NO: V.2 DATE: FEB/02/2013 PAGE: 5 OF 6 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: Y.Liu ERP: 1202000467 LED Reliability Test Report NO. REC2013001021 : : year month plan schedule Customer's requirement :Verification NO TEST ITEM 1 Continuous operating 2 High temp. and hum. storage 3 High temp. and hum. Operating 4 Solderability supplier KINGBRIGHT chip type / laboratary Kingbright Laboratary chip lot. / P/N AM2520F3C03 Scope Of Inspection WI-MQ00-R-0106 TEST DATE 2012/11/7 2012/11/7 2012/11/7 ~ 2012/12/19 ~ 2012/12/19 ~ 2012/12/19 TEST CONDITION IF=20mA T=1000hr STANDARDS JUDGEMENT LTPD SAMPLE A PASSED 10% 22pcs PASSED 10% 22pcs PASSED 10% 22pcs PASSED 20% 18PCS PASSED 20% 18PCS PASSED 10% 22pcs PASSED 10% 22pcs PASSED 10% 22pcs schedule Ta=85Degree C. T=1000hr RH=85%RH Ta=85Degree C. RH=85%RH 2012/11/9 B schedule T=1000hr IF=5mA Ta=245Degree C. T=5sec B schedule Cover 95% 5 Soldering resistance 6 Thermal shock 7 Drop 8 Vibration A 2012/11/12 Ta=260Degree C. T=10sec schedule Ta=0Degree C.~100Degree C. 2012/11/12 2012/11/14 ~ 2012/11/16 ~ 2012/11/14 T=5min~5minx100cycles 2012/11/14 H=100cm T=3cycles A schedule B schedule Accelerate speed 200m/s2 Frequency=100~2000Hz, T=48min, X.Y.Z Three directions,Four times Standard schedule Characteristics item B A schedule Specification Symbol Standards Characteristics Symbol spec Forward voltage VF(V) USL(MAX) VF VF(V) MAX 1.2 V Reverse current IR(A) USL(MAX) IR IR(uA) MAX 10 A Initial valueX0.6(min) Po PO(mW/sr) MIN 1.6 mW/sr LSL Initial SPEC LSL USL Initial SPEC USL Intensity value Apperance Po(mW/sr) / Damage remark Standard schedule Characteristics item Symbol standards Forward voltage VF(V) USL(MAX) B Reverse current IR(A) USL(MAX) Intensity value Appearance Po(mW/sr) / Initial valueX0.8(min) Damage P.S:LTPD(Lot Tolerance Percent Defective). Test:Yang Liu Checked by:Hou Gang Approved:Alex Huang