High Voltage, Bidirectional
Current Shunt Monitor
Data Sheet
AD8210
Rev. C
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700 www.analog.com
Fax: 781.461.3113 ©20062012 Analog Devices, Inc. All rights reserved.
FEATURES
±4000 V HBM ESD
High common-mode voltage range
−2 V to +65 V operating
−5 V to +68 V survival
Buffered output voltage
5 mA output drive capability
Wide operating temperature range: 40°C to +125°C
Ratiometric half-scale output offset
Excellent ac and dc performance
1 µV/°C typical offset drift
10 ppm/°C typical gain drift
120 dB typical CMRR at dc
80 dB typical CMRR at 100 kHz
Available in 8-lead SOIC
APPLICATIONS
Current sensing
Motor controls
Transmission controls
Diesel injection controls
Engine management
Suspension controls
Vehicle dynamic controls
DC-to-dc converters
FUNCTIONAL BLOCK DIAGRAM
LOAD
AD8210
VOUT
G = +20
VSUPPLY IS
RS
+IN –IN
VS
V+
VREF1
VREF2
GND
05147-001
Figure 1.
GENERAL DESCRIPTION
The AD8210 is a single-supply, difference amplifier ideal for
amplifying small differential voltages in the presence of large
common-mode voltages. The operating input common-mode
voltage range extends from −2 V to +65 V. The typical supply
voltage is 5 V.
The AD8210 is offered in a SOIC package. The operating
temperature range is40°C to +125°C.
Excellent ac and dc performance over temperature keep errors
in the measurement loop to a minimum. Offset drift and gain
drift are guaranteed to a maximum of 8 µV/°C and 20 ppm/°C,
respectively.
The output offset can be adjusted from 0.05 V to 4.9 V with
a 5 V supply by using the VREF1 pin and the VREF2 pin. With the
VREF1 pin attached to the V+ pin and the VREF2 pin attached to
the GND pin, the output is set at half scale. Attaching both VREF1
and VREF2 to GND causes the output to be unipolar, starting
near ground. Attaching both VREF1 and VREF2 to V+ causes the
output to be unipolar, starting near V+. Other offsets can be
obtained by applying an external voltage to VREF1 and VREF2.
AD8210 Data Sheet
Rev. C | Page 2 of 16
TABLE OF CONTENTS
Features .............................................................................................. 1
Applications ....................................................................................... 1
Functional Block Diagram .............................................................. 1
General Description ......................................................................... 1
Revision History ............................................................................... 2
Specifications ..................................................................................... 3
Absolute Maximum Ratings ............................................................ 4
ESD Caution .................................................................................. 4
Pin Configuration and Function Descriptions ............................. 5
Typical Performance Characteristics ............................................. 6
Theory of Operation ...................................................................... 10
Modes of Operation ....................................................................... 11
Unidirectional Operation .......................................................... 11
Bidirectional Operation ............................................................. 11
Input Filtering ................................................................................. 13
Applications Information .............................................................. 14
High-Side Current Sense with a Low-Side Switch ................. 14
High-Side Current Sense with a High-Side Switch ............... 14
H-Bridge Motor Control ........................................................... 14
Outline Dimensions ....................................................................... 15
Ordering Guide .......................................................................... 15
REVISION HISTORY
2/12Rev. B to Rev. C
Changes to Ordering Guide .......................................................... 15
5/09—Rev. A to Rev. B
Changes to Ordering Guide .......................................................... 15
4/07Rev. 0 to Rev. A
Changes to Features .......................................................................... 1
Changes to Input Section ................................................................. 3
Updated Outline Dimensions ....................................................... 15
4/06Revision 0: Initial Version
Data Sheet AD8210
Rev. C | Page 3 of 16
SPECIFICATIONS
TA = operating temperature range, VS = 5 V, unless otherwise noted.
Table 1.
AD8210 SOIC1
Parameter Min Typ Max Unit Conditions
GAIN
Initial 20 V/V
Accuracy ±0.5 % 25°C, VO ≥ 0.1 V dc
Accuracy Over Temperature ±0.7 % TA
Gain Drift 20 ppm/°C
VOLTAGE OFFSET
Offset Voltage (RTI) ±1.0 mV 25°C
Over Temperature (RTI) ±1.8 mV TA
Offset Drift ±8.0 µV/°C
INPUT
Input Impedance
Differential 2 kΩ
Common Mode 5 MΩ V common mode > 5 V
1.5 kΩ V common mode < 5 V
Common-Mode Input Voltage Range −2 +65 V Common mode, continuous
Differential Input Voltage Range 250 mV Differential2
Common-Mode Rejection 100 120 dB TA, f = dc, VCM > 5 V
80 95 dB TA, f = dc to 100 kHz3, VCM < 5 V
80 dB TA, f = 100 kHz3, VCM > 5 V
80 dB TA, f = 40 kHz3, VCM > 5 V
OUTPUT
Output Voltage Range 0.05 4.9 V RL = 25 kΩ
Output Impedance 2
DYNAMIC RESPONSE
Small Signal −3 dB Bandwidth 450 kHz
Slew Rate 3 V/µs
NOISE
0.1 Hz to 10 Hz, RTI 7 µV p-p
Spectral Density, 1 kHz, RTI 70 nV/√Hz
OFFSET ADJUSTMENT
Ratiometric Accuracy4 0.499 0.501 V/V Divider to supplies
Accuracy, RTO ±0.6 mV/V Voltage applied to VREF1 and VREF2 in parallel
Output Offset Adjustment Range
0.05
4.9
V
S
= 5 V
VREF Input Voltage Range 0.0 VS V
VREF Divider Resistor Values 24 32 40 kΩ
POWER SUPPLY, V
S
Operating Range 4.5 5.0 5.5 V
Quiescent Current Over Temperature 2 mA VCM > 5 V5
Power Supply Rejection Ratio 80 dB
TEMPERATURE RANGE
For Specified Performance −40 +125 °C
1 TMIN to TMAX = −40°C to +125°C.
2 Differential input voltage range = ±125 mV with half-scale output offset.
3 Source imbalance < 2 Ω.
4 The offset adjustment is ratiometric to the power supply when VREF1 and VREF2 are used as a divider between the supplies.
5 When the input common mode is less than 5 V, the supply current increases. This can be calculated with the following formula: IS = −0.7 (VCM) + 4.2 (see Figure 21).
AD8210 Data Sheet
Rev. C | Page 4 of 16
ABSOLUTE MAXIMUM RATINGS
Table 2.
Parameter Rating
Supply Voltage 12.5 V
Continuous Input Voltage (VCM) −5 V to +68 V
Reverse Supply Voltage 0.3 V
ESD Rating
HBM (Human Body Model) ±4000 V
CDM (Charged Device Model) ±1000 V
Operating Temperature Range
−40°C to +125°C
Storage Temperature Range −65°C to +150°C
Output Short-Circuit Duration Indefinite
Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress
rating only; functional operation of the device at these or any
other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability.
ESD CAUTION
Data Sheet AD8210
Rev. C | Page 5 of 16
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
05147-003
–IN
1
GND
2
V
REF
2
3
NC
4
+IN
8
V
REF
1
7
V+
6
OUT
5
NC = NO CONNECT
AD8210
TOP VIEW
(Not to Scale)
Figure 2. Pin Configuration
Table 3. Pin Function Descriptions
Pin No. Mnemonic X Y
1 −IN −443 +584
2 GND 479 +428
3 VREF2 −466 469
4 NC
5 OUT +466 −537
6 V+ +501 95
7 VREF1 +475 +477
8 +IN +443 +584
18
2
35
6
7
05147-002
Figure 3. Metallization Diagram
AD8210 Data Sheet
Rev. C | Page 6 of 16
TYPICAL PERFORMANCE CHARACTERISTICS
200
–200
–40
TEMPERATURE (°C)
VOSI V)
180
160
140
120
100
80
60
40
20
0
–20
–40
–60
–80
–100
–120
–140
–160
–180
–30–20–10010 20 30 40 50 60 70 80 90 100110120
05147-030
Figure 4. Typical Offset Drift
140
60
100100k
FREQUENCY (Hz)
CMRR (dB)
1k 10k
130
120
110
100
90
80
70
+25°C
–40°C
+125°C
05147-032
Figure 5. CMRR vs. Frequency and Temperature
(Common-Mode Voltage < 5 V)
140
60
100100k
FREQUENCY (Hz)
CMRR (dB)
1k 10k
130
120
110
100
90
80
70
+25°C
–40°C +125°C
05147-031
Figure 6. CMRR vs. Frequency and Temperature
(Common-Mode Voltage > 5 V)
2000
–2000
–40
TEMPERATURE (°C)
GAIN ERRO R ( pp m)
–30–20–10 010 20 30 40 50 60 70 80 90 100110120
1600
1200
800
400
0
–400
–800
–1200
–1600
05147-033
Figure 7. Typical Gain Drift
30
–5010 10M
FREQUENCY (Hz)
GAIN (d B)
100 1k 10k100k 1M
25
20
15
10
5
0
–5
–10
–15
–20
–25
–30
–35
–40
–45
05147-014
Figure 8. Typical Small Signal Bandwidth (VOUT = 200 mV p-p)
400ns/DIV
100mV/DIV
500mV/DIV
05147-017
Figure 9. Fall Time
Data Sheet AD8210
Rev. C | Page 7 of 16
400ns/DIV
500mV/DIV
100mV/DIV
05147-018
Figure 10. Rise Time
1µs/DIV
2V/DIV
200mV/DIV
05147-016
Figure 11. Differential Overload Recovery (Falling)
200mV/DIV
2V/DIV
1µs/DIV
05147-015
Figure 12. Differential Overload Recovery (Rising)
4µs/DIV
4V/DIV
0.02%/DIV
05147-024
Figure 13. Settling Time (Falling)
4µs/DIV
4V/DIV
0.02%/DIV
05147-025
Figure 14. Settling Time (Rising)
1µs/DIV
50V/DIV
100mV/DIV
05147-019
Figure 15. Common-Mode Response (Falling)
AD8210 Data Sheet
Rev. C | Page 8 of 16
1µs/DIV
100mV/DIV
50V/DIV
05147-020
Figure 16. Common-Mode Response (Rising)
8
0
–40
TEMPERATURE C)
MAXIMUM OUT P UT SINK CURRENT (mA)
7
6
5
4
3
2
1
–20 0 20 40 60 80 100120140
05147-022
Figure 17. Output Sink Current vs. Temperature
–40
TEMPERATURE C)
MAXIMUM OUT P UT SOURCE CURRE NT (mA)
11
9
10
8
7
6
5
4
3
2
1
0–20 0 20 40 60 80 100120140
05147-026
Figure 18. Output Source Current vs. Temperature
5.0
3.506.5
OUTPUT SOURCECURRENT (mA)
OUTPUT VOLTAGE RANGE (V)
4.9
4.8
4.7
4.6
4.5
4.4
4.3
4.2
4.1
4.0
3.9
3.8
3.7
3.6
0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0
05147-023
Figure 19. Output Voltage Range vs. Output Source Current
00
OUTPUT SINK CURRENT (mA)
OUTPUT VOLTAGE RANGE FROM GND (V)
1.4
05147-038
1.2
1.0
0.8
0.6
0.4
0.2
12 3 45678 9
Figure 20. Output Voltage Range from GND vs. Output Sink Current
6.0
1.0–2 65
COMMON-MODE VOLTAGE (V)
SUPP LY CURRENT (mA)
5.5
5.0
4.5
4.0
3.5
3.0
2.5
2.0
1.5
02468
05147-027
Figure 21. Supply Current vs. Common-Mode Voltage
Data Sheet AD8210
Rev. C | Page 9 of 16
2100
0
–10 10
VOS DRIFT
V/°C)
COUNT
1800
1500
1200
900
600
300
–9 –6 3 0369
05147-034
Figure 22. Offset Drift Distribution (µV/°C), SOIC,
Temperature Range = −40°C to +125°C
0020
GAIN DRIFT (ppm/°C)
COUNT
3500
3000
2500
2000
1500
1000
500
3 6 9 12 15 18
05147-035
Figure 23. Gain Drift Distribution (ppm/°C), SOIC,
Temperature = −40°C to +125°C
0
–2.0 2.0
VOS (mV)
COUNT
4000
3000
2000
1000
–1.5 –1.0 –0.5 00.5 1.0 1.5
+25°C
–40°C
+125°C
05147-036
Figure 24. Offset Distribution (µV), SOIC, VCM = 5 V
0
–2.0 2.0
VOS (mV)
COUNT
4000
3500
3000
2500
2000
1500
1000
500
–1.5 –1.0 –0.5 0 0.5 1.0 1.5
+25°C
–40°C
+125°C
05147-037
Figure 25. Offset Distribution (µV), SOIC, VCM = 0 V
AD8210 Data Sheet
Rev. C | Page 10 of 16
THEORY OF OPERATION
In typical applications, the AD8210 amplifies a small differential
input voltage generated by the load current flowing through a
shunt resistor. The AD8210 rejects high common-mode voltages
(up to 65 V) and provides a ground referenced buffered output
that interfaces with an analog-to-digital converter (ADC).
Figure 26 shows a simplified schematic of the AD8210.
The AD8210 is comprised of two main blocks, a differential
amplifier and an instrumentation amplifier. A load current
flowing through the external shunt resistor produces a voltage
at the input terminals of the AD8210. The input terminals are
connected to the differential amplifier (A1) by R1 and R2. A1
nulls the voltage appearing across its own input terminals by
adjusting the current through R1 and R2 with Q1 and Q2.
When the input signal to the AD8210 is 0 V, the currents in R1
and R2 are equal. When the differential signal is nonzero, the
current increases through one of the resistors and decreases in
the other. The current difference is proportional to the size and
polarity of the input signal.
The differential currents through Q1 and Q2 are converted
into a differential voltage by R3 and R4. A2 is configured as an
instrumentation amplifier. The differential voltage is converted
into a single-ended output voltage by A2. The gain is internally
set with precision-trimmed, thin film resistors to 20 V/V.
The output reference voltage is easily adjusted by the VREF1 pin
and the VREF2 pin. In a typical configuration, VREF1 is connected
to VCC while VREF2 is connected to GND. In this case, the output
is centered at VCC/2 when the input signal is 0 V.
I
SHUNT
R
SHUNT
AD8210
V
OUT
= (I
SHUNT
× R
SHUNT
) × 20
A2
R1 R2
V
S
V
REF
1
V
REF
2
GND
05147-004
A1
R3 R4
Q1 Q2
Figure 26. Simplified Schematic
Data Sheet AD8210
Rev. C | Page 11 of 16
MODES OF OPERATION
The AD8210 can be adjusted for unidirectional or bidirectional
operation.
UNIDIRECTIONAL OPERATION
Unidirectional operation allows the AD8210 to measure
currents through a resistive shunt in one direction. The basic
modes for unidirectional operation are ground referenced
output mode and V+ referenced output mode.
In unidirectional operation, the output can be set at the negative
rail (near ground) or at the positive rail (near V+) when the
differential input is 0 V. The output moves to the opposite rail
when a correct polarity differential input voltage is applied. In
this case, full scale is approximately 250 mV. The required
polarity of the differential input depends on the output voltage
setting. If the output is set at ground, the polarity needs to be
positive to move the output up (see Table 5). If the output is set
at the positive rail, the input polarity needs to be negative to
move the output down (see Table 6).
Ground Referenced Output
When using the AD8210 in this mode, both reference inputs
are tied to ground, which causes the output to sit at the negative
rail when the differential input voltage is zero (see Figure 27
and Table 4).
AD8210
OUTPUT
G = +20
R
S
+IN –IN
V
S
V
REF
1
V
REF
2
GND
05147-005
0.1µF
Figure 27. Ground Referenced Output
Table 4. V+ = 5 V
VIN (Referred to −IN) VO
0 V 0.05 V
250 mV
4.9 V
V+ Referenced Output
This mode is set when both reference pins are tied to the
positive supply. It is typically used when the diagnostic scheme
requires detection of the amplifier and wiring before power is
applied to the load (see Figure 28 and Table 5).
AD8210
OUTPUT
G = +20
R
S
+I
N –IN
V
S
V
REF
1
V
REF
2
GND
0.1µF
05147-006
Figure 28. V+ Referenced Output
Table 5. V+ = 5 V
VIN (Referred to −IN) VO
0 V 4.9 V
−250 mV 0.05 V
BIDIRECTIONAL OPERATION
Bidirectional operation allows the AD8210 to measure currents
through a resistive shunt in two directions. The output offset
can be set anywhere within the output range. Typically, it is set
at half scale for equal measurement range in both directions. In
some cases, however, it is set at a voltage other than half scale
when the bidirectional current is nonsymmetrical.
Table 6. V+ = 5 V, VO = 2.5 V with VIN = 0 V
VIN (Referred to IN) VO
+125 mV 4.9 V
−125 mV 0.05 V
Adjusting the output can also be accomplished by applying
voltage(s) to the reference inputs.
AD8210 Data Sheet
Rev. C | Page 12 of 16
External Referenced Output
Tying both VREF pins together to an external reference produces
an output offset at the reference voltage when there is no
differential input (see Figure 29). When the input is negative
relative to the −IN pin, the output moves down from the
reference voltage. When the input is positive relative to the
−IN pin, the output increases.
AD8210
OUTPUT
G = +20
RS
+IN –IN
VS
VREF1
VREF2
GND
VREF
05147-007
0.1µF
0V VREF VS
Figure 29. External Reference Output
Splitting an External Reference
In this case, an external reference is divided by two with
an accuracy of approximately 0.2% by connecting one
VREF pin to ground and the other VREF pin to the reference
voltage (see Figure 30).
Note that Pin VREF1 and Pin VREF2 are tied to internal precision
resistors that connect to an internal offset node. There is no
operational difference between the pins.
For proper operation, the AD8210 output offset should not be
set with a resistor voltage divider. Any additional external
resistance could create a gain error. A low impedance voltage
source should be used to set the output offset of the AD8210.
AD8210
OUTPUT
G = +20
R
S
+IN –IN
V
S
V
REF
1
V
REF
2
GND
05147-008
0.1µF
V
REF
0V V
REF
V
S
Figure 30. Split External Reference
Splitting the Supply
By tying one reference pin to V+ and the other to the GND pin,
the output is set at midsupply when there is no differential input
(see Figure 31). This mode is beneficial because no external
reference is required to offset the output for bidirectional
current measurement. This creates a midscale offset that is
ratiometric to the supply, meaning that if the supply increases
or decreases, the output still remains at half scale. For example,
if the supply is 5.0 V, the output is at half scale or 2.5 V. If the
supply increases by 10% (to 5.5 V), the output also increases by
10% (2.75 V).
0.1µF
AD8210
OUTPUT
G = +20
R
S
+IN –IN
V
S
V
REF
1
V
REF
2
GND
05147-009
Figure 31. Split Supply
Data Sheet AD8210
Rev. C | Page 13 of 16
INPUT FILTERING
In typical applications, such as motor and solenoid current
sensing, filtering at the input of the AD8210 can be beneficial
in reducing differential noise, as well as transients and current
ripples flowing through the input shunt resistor. An input low-
pass filter can be implemented as shown in Figure 32.
The 3 dB frequency for this filter can be calculated by
FILTERFILTER
CR
f××
=π2
1
dB3_
(1)
Adding outside components, such as RFILTER and CFILTER,
introduces additional errors to the system. To minimize these
errors as much as possible, it is recommended that RFILTER be
10 Ω or lower. By adding the RFILTER in series with the 2 kΩ
internal input resistors of the AD8210, a gain error is
introduced. This can be calculated by
×=
FILTER
R
ErrorGain 2
2
100100(%)
(2)
AD8210
OUTPUT
G = +20
R
SHUNT
< R
FILTER
C
FILTER
R
FILTER
10R
FILTER
10
+IN –IN
V
S
V
REF
1
V
REF
2
GND
V
REF
05147-013
0.1µF
0V V
REF
V
S
Figure 32. Input Low-Pass Filtering
AD8210 Data Sheet
Rev. C | Page 14 of 16
APPLICATIONS INFORMATION
The AD8210 is ideal for high-side or low-side current sensing.
Its accuracy and performance benefits applications, such as
3-phase and H-bridge motor control, solenoid control, and
power supply current monitoring.
For solenoid control, two typical circuit configurations are used:
high-side current sense with a low-side switch, and high-side
current sense with a high-side switch.
HIGH-SIDE CURRENT SENSE WITH A LOW-SIDE
SWITCH
In this case, the PWM control switch is ground referenced. An
inductive load (solenoid) is tied to a power supply. A resistive
shunt is placed between the switch and the load (see Figure 33).
An advantage of placing the shunt on the high side is that the
entire current, including the recirculation current, can be meas-
ured because the shunt remains in the loop when the switch is
off. In addition, diagnostics can be enhanced because short circuits
to ground can be detected with the shunt on the high side.
05147-010
INDUCTIVE
LOAD
CLAMP
DIODE
BATTERY
SHUNT
SWITCH
NC = NO CONNECT
5V
+IN V
REF
1+V
S
OUT
–IN GND V
REF
2 NC
AD8210
0.1µF
Figure 33. Low-Side Switch
In this circuit configuration, when the switch is closed, the
common-mode voltage moves down to the negative rail. When
the switch is opened, the voltage reversal across the inductive
load causes the common-mode voltage to be held one diode
drop above the battery by the clamp diode.
HIGH-SIDE CURRENT SENSE WITH A HIGH-SIDE
SWITCH
This configuration minimizes the possibility of unexpected
solenoid activation and excessive corrosion (see Figure 34). In
this case, both the switch and the shunt are on the high side.
When the switch is off, the battery is removed from the load,
which prevents damage from potential short circuits to ground,
while still allowing the recirculation current to be measured and
diagnostics to be preformed. Removing the power supply from
the load for the majority of the time minimizes the corrosive
effects that could be caused by the differential voltage between
the load and ground.
05147-011
INDUCTIVE
LOAD
CLAMP
DIODE
BATTERY
SHUNT
SWITCH
NC = NO CONNECT
5V
+IN VREF1+VSOUT
–IN GND VREF2NC
AD8210
0.1µF
Figure 34. High-Side Switch
Using a high-side switch connects the battery voltage to the
load when the switch is closed. This causes the common-mode
voltage to increase to the battery voltage. In this case, when the
switch is opened, the voltage reversal across the inductive load
causes the common-mode voltage to be held one diode drop
below ground by the clamp diode.
H-BRIDGE MOTOR CONTROL
Another typical application for the AD8210 is as part of the
control loop in H-bridge motor control. In this case, the AD8210
is placed in the middle of the H-bridge (see Figure 35) so that it
can accurately measure current in both directions by using the
shunt available at the motor. This configuration is beneficial for
measuring the recirculation current to further enhance the
control loop diagnostics.
05147-012
SHUNT
2.5V
5V
CONTROLLER
NC = NO CONNECT
MOTOR
5V
+IN VREF1+VSOUT
–IN GND VREF2 NC
AD8210
0.1µF
Figure 35. Motor Control Application
The AD8210 measures current in both directions as the H-bridge
switches and the motor changes direction. The output of the
AD8210 is configured in an external reference bidirectional
mode (see the Modes of Operation section).
Data Sheet AD8210
Rev. C | Page 15 of 16
OUTLINE DIMENSIONS
CONTROLLING DIMENSIONS ARE IN MILLIMETERS; INCH DIMENSI
ONS
(IN PARENTHESES) ARE ROUNDED-OFF MILLIMETER EQUIVALENTS FOR
REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN.
COMPLIANT TO JEDEC STANDARDS MS-012-AA
012407-A
0.25 (0.0098)
0.17 (0.0067)
1.27 (0.0500)
0.40 (0.0157)
0.50 (0.0196)
0.25 (0.0099) 45°
1
.75 (0.0688)
1.35 (0.0532)
SEATING
PLANE
0.25 (0.0098)
0.10 (0.0040)
4
1
8 5
5.00(0.1968)
4.80(0.1890)
4.00 (0.1574)
3.80 (0.1497)
1.27 (0.0500)
BSC
6.20 (0.2441)
5.80 (0.2284)
0.51 (0.0201)
0.31 (0.0122)
COPLANARITY
0.10
Figure 36. 8-Lead Standard Small Outline Package [SOIC_N]
Narrow Body (R-8)
Dimensions shown in millimeters and (inches)
ORDERING GUIDE
Model1 Temperature Range Package Description Package Option
AD8210YRZ 40°C to +125°C 8-Lead SOIC_N R-8
AD8210YRZ-REEL 40°C to +125°C 8-Lead SOIC_N, 13” Tape and Reel R-8
AD8210YRZ-REEL7 40°C to +125°C 8-Lead SOIC_N, 7” Tape and Reel R-8
AD8210WYRZ 40°C to +125°C 8-Lead SOIC_N R-8
AD8210WYRZ-RL
40°C to +125°C
8-Lead SOIC_N, 13 Tape and Reel
R-8
AD8210WYRZ-R7 40°C to +125°C 8-Lead SOIC_N, 7” Tape and Reel R-8
AD8210WYC-P3 40°C to +125°C Die
1 Z = RoHS Compliant Part.
AD8210 Data Sheet
Rev. C | Page 16 of 16
NOTES
©20062012 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D05147-0-2/12(C)