RO3134A * * * * Very Low Series Resistance Quartz Stability Surface-mount Ceramic Case Complies with Directive 2002/95/EC (RoHS) 372.5 MHz SAW Resonator Pb The RO3134A is a true one-port, surface-acoustic-wave (SAW) resonator in a surface-mount, ceramic case. It provides reliable, fundamental-mode, quartz frequency stabilization of local oscillators operating at approximately 372.5 MHz. Absolute Maximum Ratings Rating Value Units CW RF Power Dissipation (See Typical Test Circuit) +10 dBm DC Voltage Between Terminals (Observe ESD Precautions) 30 VDC -40 to +85 C 260 C Case Temperature Soldering Temperature (10 seconds / 5 cycles maximum) SM5035-4 Electrical Characteristics Characteristic Frequency, +25 C Sym fC Nominal Frequency Tolerance from 372.500 MHz fC Insertion Loss Quality Factor Temperature Stability Frequency Aging IL Unloaded Q QU 50 Loaded Q QL Turnover Temperature TO Turnover Frequency fO Absolute Value during the First Year RM Motional Inductance LM Motional Capacitance CM Shunt Static Capacitance Units 372.600 MHz 100 kHz 2.2 dB 40 C 1,700 25 fC 0.032 1, 6 5 Maximum 15,400 6, 7, 8 |fA| Motional Resistance 1.0 10 FTC Typical 372.400 5, 6, 7 Frequency Temperature Coefficient Test Fixture Shunt Inductance 2, 3, 4, 5 Minimum 2, 5, 6 DC Insulation Resistance between Any Two Terminals RF Equivalent RLC Model Notes 10 1.0 5, 6, 7, 9 ppm/C2 ppm/yr M 12.7 83 H 2.2 fF CO 5, 6, 9 2.4 pF LTEST 2, 7 76 nH Lid Symbolization 836//YYWWSR CAUTION: Electrostatic Sensitive Device. Observe precautions for handling. Notes: 1. 2. 3. 4. 5. 6. Frequency aging is the change in fC with time and is specified at +65 C or less. Aging may exceed the specification for prolonged temperatures above +65 C. Typically, aging is greatest the first year after manufacture, decreasing in subsequent years. The center frequency, fC, is measured at the minimum insertion loss point, ILMIN, with the resonator in the 50 test system (VSWR 1.2:1). The shunt inductance, LTEST, is tuned for parallel resonance with CO at fC. Typically, fOSCILLATOR or fTRANSMITTER is approximately equal to the resonator fC. One or more of the following United States patents apply: 4,454,488 and 4,616,197. Typically, equipment utilizing this device requires emissions testing and government approval, which is the responsibility of the equipment manufacturer. Unless noted otherwise, case temperature TC = +25 2 C. The design, manufacturing process, and specifications of this device www.RFM.com E-mail: info@rfm.com (c) 2008-2011 by RF Monolithics, Inc. 7. 8. 9. are subject to change without notice. Derived mathematically from one or more of the following directly measured parameters: fC, IL, 3 dB bandwidth, fC versus TC, and CO. Turnover temperature, TO, is the temperature of maximum (or turnover) frequency, fO. The nominal frequency at any case temperature, TC, may be calculated from: f = fO [1 - FTC (TO -TC)2]. Typically oscillator TO is approximately equal to the specified resonator TO. This equivalent RLC model approximates resonator performance near the resonant frequency and is provided for reference only. The capacitance CO is the static (nonmotional) capacitance between the two terminals measured at low frequency (10 MHz) with a capacitance meter. The measurement includes parasitic capacitance with "NC" pads unconnected. Case parasitic capacitance is approximately 0.05 pF. Transducer parallel capacitance can by calculated as: CP CO - 0.05 pF. Page 1 of 2 RO3134A - 6/29/11 Electrical Connections Equivalent Model The SAW resonator is bidirectional and may be installed with either orientation. The two terminals are interchangeable and unnumbered. The callout NC indicates no internal connection. The NC pads assist with mechanical positioning and stability. External grounding of the NC pads is recommended to help reduce parasitic capacitance in the circuit. 0.05 pF* Case Ground Case Ground Terminal Co = Cp + 0.05 pF Cp Terminal Lm Rm *Case Parasitics Cm Temperature Characteristics The test circuit inductor, LTEST, is tuned to resonate with the static capacitance, CO, at FC. The curve shown on the right accounts for resonator contribution only and does not include LC component temperature contributions. fC = f O , T C = T O -50 -50 -100 -100 -150 -150 -200 0 +20 +40 +60 +80 -200 -80 -60 -40 -20 ELECTRICAL TEST Case T = T C - T O ( C ) To 50 Network Analyzer From 50 Network Analyzer 0 0 (f-fo ) / fo (ppm) Typical Test Circuit T o p V ie w S id e V ie w B C B o tto m V ie w E (3 x ) 4 F (4 x ) 1 A POWER TEST 3 P INCIDENT 50 Source P at F C REFLECTED CW RF Power Dissipation = Low-Loss Matching Network to 50 2 Terminal G (1 x ) NC NC D Terminal H P INCIDENT - P REFLECTED I Typical Application Circuits J Typical Low-Power Transmitter Application K +9VDC L 200k Modulation Input C1 47 H L1 (Antenna) M J M H PCB Land Pattern Top View C2 RF Bypass RO3XXXA Bottom View Dimensions 470 Typical Local Oscillator Applications Output +VDC C1 +VDC L1 C2 RO3XXXA Bottom View www.RFM.com E-mail: info@rfm.com (c) 2008-2011 by RF Monolithics, Inc. RF Bypass Millimeters Inches Min Nom Max Min Nom Max A 4.87 5.00 5.13 0.191 0.196 0.201 B 3.37 3.50 3.63 0.132 0.137 0.142 C 1.45 1.53 1.60 0.057 0.060 0.062 D 1.35 1.43 1.50 0.040 0.057 0.059 E 0.67 0.80 0.93 0.026 0.031 0.036 F 0.37 0.50 0.63 0.014 0.019 0.024 G 1.07 1.20 1.33 0.042 0.047 0.052 H - 1.04 - - 0.041 - I - 1.46 - - 0.058 - J - 0.50 - - 0.019 - K - 1.05 - - 0.041 - L - 1.44 - - 0.057 - M - 0.71 - - 0.028 - Page 2 of 2 RO3134A - 6/29/11