ANALOG DEVICES 3.3 V Supply, Voltage Output Temperature Sensor with Signal Conditioning AD22103* FEATURES 3.3 V, Single Supply Operation Temperature Coefficient of 28 mV/C 100C Temperature Span (0C to +100C) Accuracy Better Than 2.5% of Full Scale Linearity Better Than 0.5% of Full Scale Output Proportional to Temperature x Vs Minimal Self-Heating High Level, Low Impedance Output Reverse Supply Protected APPLICATIONS Microprocessor Thermal Management Battery and Low Powered Systems Power Supply Temperature Monitoring System Temperature Compensation Board Level Temperature Sensing MARKETS Computers Portable Electronic Equipment Industrial Process Control Instrumentation GENERAL DESCRIPTION The AD22103 is a monolithic temperature sensor with on-chip signal conditioning. It can be operated over the temperature range 0C to +100C, making it ideal for use in numerous 3.3 V applications. The signal conditioning eliminates the need for any trimming, buffering or linearization circuitry, greatly simplifying the system design and reducing the overall system cost. The output voltage is proportional to the temperature times the supply voltage (ratiometric). The output swings from 0.25 V at 0C to +3.05 V at +100C using a single +3.3 V supply. Due to its ratiometric nature, the AD22103 offers a cost effec- tive solution when interfacing to an analog-to-digital converter. This is accomplished by using the ADCs power supply as a ref- erence to both the ADC and the AD22103 (See Figure 1), eliminating the need for and cost of a precision reference. *Protected by U.S. Patent Nos. 5030849 and 5243319, REV. 0 Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. SIMPLIFIED BLOCK DIAGRAM Vs +3.3V e ~-(.) REFERENCE } ANALOG TO ad DIGITAL AD22103 SIGNAL OUTPUT CONVERTER Vo _ DIRECT TO ADC > INPUT 1k2 y 0.1pF O t Vv Figure 1. Application Circuit Analog Devices, Inc., 1995 One Technology Way, P.O. Box 9106, Norwood. MA 02062-9106, U.S.A. Tel: 617/329-4700 Fax: 617/326-8703AD221 03SPEC | Fl CATI 0 NS (Ty = +25C and Vs = +2.7 V to +3.6 V unless otherwise noted) AD22103K Parameter Min Typ Max Units TRANSFER FUNCTION Vout = (Vs/3.3 V) x [0.25 V + 28 mV/C) x Ta] Vv TEMPERATURE COEFFICIENT (Vs/3.3 V) x 28 mvV/C TOTAL ERROR Initial Error Ta = +25C +0.5 +2.0 C Error over Temperature Ta =Twm to Tax +0.75 +2.5 C Nonlinearity Ta = Tur to Tyax 0.1 0.5 % Fs! OUTPUT CHARACTERISTICS Nominal Output Voltage Vs = 3.3 V, Ta = 0C 0.25 Vv Vs = 3.3 V, Ta = +25C 0.95 Vv Vs = 3.3 V, Ta = +100C 3.05 Vv POWER SUPPLY Operating Voltage +2.7 +3,3 +3.6 Vv Quiescent Current 350 500 600 pA TEMPERATURE RANGE Guaranteed Temperature Range 0 +100 C Operating Temperature Range 0 +100 C PACKAGE TO-92 SOIC NOTES 'RS (Full Scale) is defined as that of the operating temperature range, 0C to +100C, The listed max specification limit applies to the guaranteed temperature range. For example, the AD22103K has a nonlinearity of (0.5%) x (100C) = 0.5C over the guaranteed temperature range of 0C to +100C, Specifications subject to change without notice. CH IP SPECIFICATIONS (Ty, = +25C and Vs = +3.3 V unless otherwise noted) Parameter Min Typ Max Units TRANSFER FUNCTION Vour = (V3s/3.3 V) x [0.25 V + 28 mV/C) x Ta] Vv TEMPERATURE COEFFICIENT (Vs/3.3 V) x 28 mvV/C OUTPUT CHARACTERISTICS Error Ta = +25C +0.5 Note 1 C Nominal Output Voltage Ta = +25C 0.95 Vv POWER SUPPLY Operating Voltage +2.7 +3,3 +3.6 Vv Quiescent Current 350 500 600 pA TEMPERATURE RANGE Guaranteed Temperature Range 25 C Operating Temperature Range 0 +100 C NOTES Max specs cannot be guaranteed on chips, however, performance once assembled should be commensurate with the specifications listed in the top table, Specifications subject to change without notice. REV. 0AD22103 ABSOLUTE MAXIMUM RATINGS* Supply Voltage .. 0... cece ee eee eee eee +10 V Reversed Continuous Supply Voltage ............... -10V Operating Temperature ...............2.4. 0C to +100C Storage Temperature ............. 0.000. 65C to +160C Output Short Circuit to Vs or Ground ............ Indefinite Lead Temperature (Soldering, 10 sec) ............. +300C *Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only; the functional operation of the device at these or any other conditions above those indicated in the operation sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. PIN DESCRIPTION Mnemonic Function Vs Power Supply Input Vo Device Output GND Ground Pin Must Be Connected to 0 V NC No Connect PIN CONFIGURATIONS TO-92 ORDERING GUIDE AD22103 BOTTOM VIEW Guaranteed PIN ema IN 1 Temperature Package Package oog Model/Grade Range Description | Option GND Vo Vs AD22103KT 0C to +100C | TO-92 TO-92 AD22103KR 0C to +100C | SOIC SO-8 AD22103KChips* | +25C N/A N/A SOIC *Minimum purchase quantities of 100 pieces for all chip orders. Vs E] Vo [2] AD22103 TOP VIEW NC [3] (Not to Scale)| 6| NC GND [4] Nc = NO CONNECT CAUTION ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily accumulate on the human body and test equipment and can discharge without detection. Although the AD22103 features proprietary ESD protection circuitry, permanent damage may occur on devices subjected to high energy electrostatic discharges. Therefore, proper ESD precautions are recommended to avoid performance degradation or loss of functionality. ca ESD SENSITIVE DEVICE Typical Performance Curves 18 250 14 200 12 (SOIC) T (TO-92) g 10 = S 5 7 150 b 8 s Oo 6 100 4 (TO-92) 2 50 0 400 800 1200 0 400 800 1200 FLOW RATE - CFM FLOW RATE - CFM Figure 2. Thermal Response vs. Air Flow Rate Figure 3. Thermal Resistance vs. Air Flow Rate REV. 0 -3-AD22103 THEORY OF OPERATION The AD22103 is a ratiometric temperature sensor IC whose output voltage is proportional to power supply voltage. The heart of the sensor is a proprietary temperature-dependent resis- tor, similar to an RTD, which is built into the IC. Figure 4 shows a simplified block diagram of the AD22103. +Vg 9 AAA VVV P Vour Rr 5 > 4 v Figure 4. Simplified Block Diagram The temperature-dependent resistor, labeled R-, exhibits a change in resistance that is nearly linearly proportional to tem- perature. This resistor is excited with a current source that is proportional to power supply voltage. The resulting voltage across R-+ is therefore both supply voltage proportional and lin- early varying with temperature. The remainder of the AD22103 consists of an op amp signal conditioning block that takes the voltage across Rr and applies the proper gain and offset to achieve the following output voltage function: Vour = (Vs/3.3 V) x [0.25 V + (28.0 mVIC) x Ta] ABSOLUTE ACCURACY AND NONLINEARITY SPECIFICATIONS Figure 5 graphically depicts the guaranteed limits of accuracy for the AD22103 and shows the performance of a typical part. As the output is very linear, the major sources of error are offset, 1.., error at room temperature, and span error, i.e., deviation from the theoretical 28.0 mV/C. Demanding applications can achieve improved performance by calibrating these offset and gain errors so that only the residual nonlinearity remains as a source of error. 2.5 2.0 1.5 1.0 0.5 ERROR - C 50 TEMPERATURE C 100 Figure 5. Typical AD22103 Performance OUTPUT STAGE CONSIDERATIONS As previously stated, the AD22103 is a voltage output device. A basic understanding of the nature of its output stage is useful for proper application. Note that at the nominal supply voltage of 3.3 V, the output voltage extends from 0.25 V at 0C to +3.05 V at +100C. Furthermore, the AD22103 output pin is capable of withstanding an indefinite short circuit to either ground or the power supply. These characteristics are provided by the output stage structure shown in Figure 6. Vs Vout Figure 6. Output Stage Structure The active portion of the output stage is a PNP transistor with its emitter connected to the Vs supply and collector connected to the output node. This PNP transistor sources the required amount of output current. A limited pull-down capability is provided by a fixed current sink of about -100 uA. (Here, fixed means the current sink is fairly insensitive to either sup- ply voltage or output loading conditions. The current sink ca- pability is a function of temperature, increasing its pull-down capability at lower temperatures.) Due to its limited current sinking ability, the AD22103 is inca- pable of driving loads to the Vs power supply and is instead in- tended to drive grounded loads. A typical value for short circuit current limit is 7 mA, so devices can reliably source 1 mA or 2mA. However, for best output voltage accuracy and minimal internal self-heating, output current should be kept below 1 mA. Loads connected to the Vs power supply should be avoided as the current sinking capability of the AD22103 is very limited. These considerations are typically not a problem when driving a microcontroller analog to digital converter input pin (see MICROPROCESSOR A/D INTERFACE ISSUES). MOUNTING CONSIDERATIONS If the AD22103 is thermally attached and properly protected, it can be used in any measuring situation where the maximum range of temperatures encountered is between 0C and +100C. Because plastic IC packaging technology is employed, excessive mechanical stress must be avoided when fastening the device with a clamp or screw-on heat tab. Thermally conductive epoxy or glue is recommended for typical mounting conditions. In wet or corrosive environments, an electrically isolated metal or ce- ramic well should be used to shield the AD22103. Because the part has a voltage output (as opposed to current), it offers mod- est immunity to leakage errors, such as those caused by conden- sation at low temperatures. REV. 0AD22103 THERMAL ENVIRONMENT EFFECTS The thermal environment in which the AD22103 is used deter- mines two performance traits: the effect of self-heating on accu- racy and the response time of the sensor to rapid changes in temperature. In the first case, a rise in the IC junction tempera- ture above the ambient temperature is a function of two variables; the power consumption of the AD22103 and the thermal resis- tance between the chip and the ambient environment 64. Self- heating error in degrees Celsius can be derived by multiplying the power dissipation by ,;,, Because errors of this type can vary widely for surroundings with different heat sinking capacities, it is necessary to specify 6;, under several conditions. Table I shows how the magnitude of self-heating error varies relative to the environment. A typical part will dissipate about 1.5 mW at room temperature with a 3.3 V supply and negligible output loading. In still air, without a heat sink, the table below indi- cates a O74 of 190C/W, yielding a temperature rise of 0.285C. Thermal rise will be considerably less in either moving air or with direct physical connection to a solid (or liquid) body. Table I. Thermal Resistance (TO-92) Medium Ora CC/Watt) t (sec)* Aluminum Block 60 2 Moving Air** Without Heat Sink 75 3.5 Still Air Without Heat Sink 190 15 *The time constant t is defined as the time to reach 63.2% of the final temperature change. **1200 CFM. Response of the AD22103 output to abrupt changes in ambient temperature can be modeled by a single time constant 1 expo- nential function. Figure 7 shows typical response time plots for a few media of interest. 100 % OF FINAL VALUES 0 10 20 30 40 50 60 70 80 90 100 TIME sec Figure 7. Response Time The time constant t is dependent on 9y, and the specific heat capacities of the chip and the package. Table I lists the effec- tive t (time to reach 63.2% of the final value) for a few different media. Copper printed circuit board connections were REV. 0 neglected in the analysis; however, they will sink or conduct heat directly through the AD22103s solder plated copper leads. When faster response is required, a thermally conductive grease or glue between the AD22103 and the surface temperature being measured should be used. MICROPROCESSOR A/D INTERFACE ISSUES The AD22103 is especially well suited to providing a low cost temperature measurement capability for microprocessor/ microcontroller based systems. Many inexpensive 8-bit micro- processors now offer an onboard 8-bit ADC capability at a mod- est cost premium. Total cost of ownership then becomes a function of the voltage reference and analog signal conditioning necessary to mate the analog sensor with the microprocessor ADC. The AD22103 can provide an ideal low cost system by eliminating the need for a precision voltage reference and any additional active components. The ratiometric nature of the AD22103 allows the microprocessor to use the same power sup- ply as its ADC reference. Variations of hundreds of millivolts in the supply voltage have little effect as both the AD22103 and the ADC use the supply as their reference. The nominal AD22103 signal range of 0.25 V to 3.05 V (OC to +100C) makes good use of the input range of a0 V to 3.3 V ADC. A single resistor and capacitor are recommended to provide im- munity to the high speed charge dump glitches seen at many microprocessor ADC inputs (see Figure 1). An 8-bit ADC with a reference of 3.3 V will have a least signifi- cant bit (LSB) size of 3.3 V/256 = 12.9 mV. This corresponds to a nominal resolution of about 0.46C/bit. USE WITH A PRECISION REFERENCE AS THE SUPPLY VOLTAGE While the ratiometric nature of the AD22103 allows for system operation without a precision voltage reference, it can still be used in such systems. Overall system requirements involving other sensors or signal inputs may dictate the need for a fixed precision ADC reference. The AD22103 can be converted to absolute voltage operation by using a precision reference as the supply voltage. For example, a 3.3 V reference can be used to power the AD22103 directly. Supply current will typically be 500 vA which is usually within the output capability of the refer- ence. A large number of AD22103s may require an additional op amp buffer, as would scaling down a 10.00 V reference that might be found in instrumentation ADCs typically operating from +15 V supplies. USING THE AD22103 WITH ALTERNATIVE SUPPLY VOLTAGES Because of its ratiometric nature the AD22103 can be used at other supply voltages. Its nominal transfer function can be recal- culated based on the new supply voltage. For instance, if using the AD22103 at Vs = 5 V the transfer function would be given by: _Vs 28 mV 5V Vo sy (0.257 +25n xT) Sap _Vs 42.42 mV Vo = (0.378 ve xT y)AD22103 OUTLINE DIMENSIONS Dimensions shown in inches and (mm). TO-92 0.205 (5.20) (649) *| 0.175 (4.96) abs 210 (5.33) 0.170 (4.38) SEATING 0.050 PLANE (1.27) MAX 0.500 0.019 (0.482) (12.70) 0.016 (0.407) MIN SQUARE 0.055 (1.39) 0.105 (2.66) it . 0.045 (1.15 0.095 (2.42) os) 0.105 (2.66) 0.080 (2.42) [*__ fF -_ 0.165 (4.19) 0.105 (2.66) 0.125 (3.94) 0.080 (2.42) + J 4 BOTTOM VIEW SO-8 (SOIC) 0.1968 (5.00) ~ | 0.1890 (4.80) fl i Afi 8 5 0.2440 (6.20) || 0.1574 (4.00) 0.2284 (5.80) 0.1497 (3.80) 4 4 EEO PIN7 0.0688 (1.75) 0.0196 (0.50) 0.0532 (1.35) [* 0.0099 (0.25) * 0.0098 (0.25) +o + 0.0040 (0.10) AA} he te & lle 0.0500 0.0192 (0.49) Y 0.0500 (1.27) SEATING (1.27) 9.0138 (0.85) 0:0098 (0.25) 0.0760 (0.41) PLANE BSC 0.0075 (0.19) REV. 0 C2006-18-3/95 PRINTED IN U.S.A.