OPA350 OPA2350 OPA4350 SBOS099C - SEPTEMBER 2000 - REVISED JANUARY 2005 High-Speed, Single-Supply, Rail-to-Rail OPERATIONAL AMPLIFIERS MicroAmplifiertSeries FEATURES DESCRIPTION D D D D D D D D D The OPA350 series rail-to-rail CMOS operational amplifiers are optimized for low voltage, single-supply operation. Rail-to-rail input/output, low noise (5nV/Hz), and high speed operation (38MHz, 22V/s) make them ideal for driving sampling Analog-to-Digital (A/D) converters. They are also well suited for cell phone PA control loops and video processing (75 drive capability) as well as audio and general purpose applications. Single, dual, and quad versions have identical specifications for maximum design flexibility. RAIL-TO-RAIL INPUT RAIL-TO-RAIL OUTPUT (within 10mV) WIDE BANDWIDTH: 38MHz HIGH SLEW RATE: 22V/s LOW NOISE: 5nV/Hz LOW THD+NOISE: 0.0006% UNITY-GAIN STABLE MicroSIZE PACKAGES SINGLE, DUAL, AND QUAD The OPA350 series operates on a single supply as low as 2.5V with an input common-mode voltage range that extends 300mV below ground and 300mV above the positive supply. Output voltage swing is to within 10mV of the supply rails with a 10k load. Dual and quad designs feature completely independent circuitry for lowest crosstalk and freedom from interaction. APPLICATIONS D D D D D D D D D CELL PHONE PA CONTROL LOOPS DRIVING A/D CONVERTERS VIDEO PROCESSING DATA ACQUISITION PROCESS CONTROL AUDIO PROCESSING COMMUNICATIONS ACTIVE FILTERS TEST EQUIPMENT The single (OPA350) and dual (OPA2350) come in the miniature MSOP-8 surface mount, SO-8 surface mount, and DIP-8 packages. The quad (OPA4350) packages are the space-saving SSOP-16 surface mount and SO-14 surface mount. All are specified from -40C to +85C and operate from -55C to +150C. SPICE model available at www.ti.com OPA350 NC 1 8 NC -In 2 7 V+ +In 3 6 Output V- 4 5 NC OPA4350 OPA4350 Out A 1 14 Out D -In A 2 13 - In D +In A 3 12 +In D V+ 4 11 V- A D DIP-8, SO-8, MSOP-8 OPA2350 +In B Out A 1 -In A 2 +In A 3 - 4 8 A B 5 7 Out B 6 -In B 5 +In B 10 B V+ +In C C -In B 6 9 - In C Out B 7 8 Out C Out A 1 16 Out D - In A 2 15 -In D +In A 3 14 +In D A D +V 4 13 -V +In B 5 12 +In C - In B 6 11 -In C Out B 7 10 Out C NC 8 9 NC B C SO-14 SSOP-16 DIP-8, SO-8, MSOP-8 Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. All trademarks are the property of their respective owners. Copyright 2000-2005, Texas Instruments Incorporated ! ! www.ti.com "#$ %"#$ &"#$ www.ti.com SBOS099C - SEPTEMBER 2000 - REVISED JANUARY 2005 ABSOLUTE MAXIMUM RATINGS(1) ELECTROSTATIC DISCHARGE SENSITIVITY Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.0V Signal Input Terminals(2), Voltage . . . . . (V-) - 0.3V to (V+) + 0.3V Current . . . . . . . . . . . . . . . . . . . . . . 10mA Open Short-Circuit Current(3) . . . . . . . . . . . . . . . . . . . . Continuous Operating Temperature Range . . . . . . . . . . . . . . . -55C to +150C Storage Temperature Range . . . . . . . . . . . . . . . . . -55C to +150C Junction Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +150C Lead Temperature (soldering, 10s) . . . . . . . . . . . . . . . . . . . . . +300C (1) Stresses above these ratings may cause permanent damage. Exposure to absolute maximum conditions for extended periods may degrade device reliability. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those specified is not implied. (2) Input terminals are diode-clamped to the power-supply rails. Input signals that can swing more than 0.3V beyond the supply rails should be current limited to 10mA or less. (3) Short-circuit to ground, one amplifier per package. This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with appropriate precautions. Failure to observe proper handling and installation procedures can cause damage. ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more susceptible to damage because very small parametric changes could cause the device not to meet its published specifications. PACKAGE/ORDERING INFORMATION(1) PRODUCT PACKAGE-LEAD PACKAGE DESIGNATOR SPECIFIED TEMPERATURE RANGE PACKAGE MARKING MSOP-8 DGK -40C to +85C C50 ORDERING NUMBER TRANSPORT MEDIA, QUANTITY OPA350EA/250 Tape and Reel, 250 OPA350EA/2K5 Tape and Reel, 2500 SINGLE OPA350EA OPA350UA SO-8 D -40C to +85C OPA350UA OPA350PA DIP-8 P -40C to +85C OPA350PA OPA2350EA MSOP-8 DGK -40C to +85C D50 OPA2350UA SO-8 D -40C to +85C OPA2350UA OPA2350PA DIP-8 P -40C to +85C OPA2350PA OPA4350EA SSOP-16 DBQ -40C to +85C OPA4350EA OPA4350UA SO-14 D -40C to +85C OPA4350UA OPA350UA Rails OPA350UA/2K5 Tape and Reel, 2500 OPA350PA Rails DUAL OPA2350EA/250 Tape and Reel, 250 OPA2350EA/2K5 Tape and Reel, 2500 OPA2350UA Rails OPA2350UA/2K5 Tape and Reel, 2500 OPA2350PA Rails QUAD OPA4350EA/250 Tape and Reel, 250 OPA4350EA/2K5 Tape and Reel, 2500 OPA4350UA Rails OPA4350UA/2K5 Tape and Reel, 2500 (1) For the most current package and ordering information, see the Package Option Addendum located at the end of this data sheet. 2 "#$ %"#$ &"#$ www.ti.com SBOS099C - SEPTEMBER 2000 - REVISED JANUARY 2005 ELECTRICAL CHARACTERISTICS: VS = 2.7V to 5.5V Boldface limits apply over the temperature range, TA = -40C to +85C. VS = 5V. All specifications at TA = +25C, RL = 1k connected to VS/2 and VOUT = VS/2, unless otherwise noted. PARAMETER TEST CONDITIONS OPA350, OPA2350, OPA4350 MIN TYP(1) MAX VS = 5V 150 UNIT OFFSET VOLTAGE Input Offset Voltage VOS TA = -40C to +85C vs Temperature vs Power-Supply Rejection Ratio PSRR TA = -40C to +85C Channel Separation (dual, quad) TA = -40C to +85C VS = 2.7V to 5.5V, VCM = 0V VS = 2.7V to 5.5V, VCM = 0V 4 dc 0.15 40 500 V 1 mV V/C 150 V/V 175 V/V V/V INPUT BIAS CURRENT Input Bias Current 0.5 IB vs Temperature Input Offset Current 10 pA See Typical Characteristics 0.5 IOS 10 pA NOISE Input Voltage Noise, f = 100Hz to 400kHz Input Voltage Noise Density, f = 10kHz en Input Current Noise Density, f = 100kHz Current Noise Density, f = 10kHz in 4 Vrms 7 nV/Hz 5 nV/Hz 4 fA/Hz INPUT VOLTAGE RANGE Common-Mode Voltage Range Common-Mode Rejection Ratio VCM CMRR TA = -40C to +85C INPUT IMPEDANCE TA = -40C to +85C VS = 2.7V, -0.1V < VCM < 2.8V VS = 5.5V, -0.1V < VCM < 5.6V -0.1 VS = 5.5V, -0.1V < VCM < 5.6V 74 (V+) + 0.1 V 66 84 dB 74 90 dB Differential Common-Mode dB 1013 || 2.5 1013 || 6.5 || pF 122 dB || pF OPEN-LOOP GAIN Open-Loop Voltage Gain AOL TA = -40C to +85C TA = -40C to +85C FREQUENCY RESPONSE Gain-Bandwidth Product Slew Rate 100 100 dB 120 dB dB G=1 38 MHz G=1 22 V/s G = 1, 2V Step 0.22 s G = 1, 2V Step 0.5 s 0.1 s 0.0006 % Overload Recovery Time Differential Phase Error RL = 1kW, 200mV < VO < (V+) -200mV CL = 100pF 100 SR 0.01% Differential Gain Error 100 GBW Settling Time: 0.1% Total Harmonic Distortion + Noise RL = 10k, 50mV < VO < (V+) -50mV RL = 10kW, 50mV < VO < (V+) -50mV RL = 1k, 200mV < VO < (V+) -200mV THD+N VIN * G = VS RL = 600, VO = 2.5VPP(2), G = 1, f = 1kHz G = 2, RL = 600, VO = 1.4V(3) G = 2, RL = 600, VO = 1.4V(3) 0.17 % 0.17 deg (1) VS = +5V. (2) VOUT = 0.25V to 2.75V. (3) NTSC signal generator used. See Figure 6 for test circuit. (4) Output voltage swings are measured between the output and power supply rails. (5) See typical characteristic curve, Output Voltage Swing vs Output Current. 3 "#$ %"#$ &"#$ www.ti.com SBOS099C - SEPTEMBER 2000 - REVISED JANUARY 2005 ELECTRICAL CHARACTERISTICS: VS = 2.7V to 5.5V (continued) Boldface limits apply over the temperature range, TA = -40C to +85C. VS = 5V. All specifications at TA = +25C, RL = 1k connected to VS/2 and VOUT = VS/2, unless otherwise noted. PARAMETER TEST CONDITIONS OPA350, OPA2350, OPA4350 MIN TYP(1) MAX UNIT 10 50 mV 50 mV 200 mV 200 mV OUTPUT Voltage Output Swing from Rail(4) VOUT TA = -40C to +85C TA = -40C to +85C Output Current Short-Circuit Current Capacitive Load Drive RL = 10k, AOL 100dB RL = 10kW, AOL 100dB RL = 1k, AOL 100dB 25 RL = 1kW, AOL 100dB IOUT ISC CLOAD 40(5) mA 80 mA See Typical Characteristics POWER SUPPLY Operating Voltage Range VS TA = -40C to +85C 2.7 Minimum Operating Voltage Quiescent Current (per amplifier) 5.5 V 7.5 mA 8.5 mA 2.5 IQ TA = -40C to +85C TEMPERATURE RANGE IO = 0 IO = 0 5.2 V Specified Range -40 +85 C Operating Range -55 +150 C Storage Range -55 +150 C Thermal Resistance qJA MSOP-8 Surface Mount 150 C/W SO-8 Surface Mount 150 C/W DIP-8 100 C/W SO-14 Surface Mount 100 C/W SSOP-16 Surface Mount 100 C/W (1) VS = +5V. (2) VOUT = 0.25V to 2.75V. (3) NTSC signal generator used. See Figure 6 for test circuit. (4) Output voltage swings are measured between the output and power supply rails. (5) See typical characteristic curve, Output Voltage Swing vs Output Current. 4 "#$ %"#$ &"#$ www.ti.com SBOS099C - SEPTEMBER 2000 - REVISED JANUARY 2005 TYPICAL CHARACTERISTICS All specifications at TA = +25C, VS = +5V, and RL = 1k connected to VS/2, unless otherwise noted. POWER SUPPLY AND COMMON-MODE REJECTION RATIO vs FREQUENCY OPEN-LOOP GAIN/PHASE vs FREQUENCY 160 100 0 90 80 -90 60 G PSRR, CMRR (dB) 100 -135 40 PSRR 80 -45 120 Phase (_) Voltage Gain (dB) 140 20 70 CMRR (VS = +5V VCM = -0.1V to 5.1V) 60 50 40 30 20 0 0.1 1 10 100 1k 10k 100k Frequency (Hz) -180 10M 100M 1M 10 0 10 100 1k 10k 100k 1M 10M Frequency (Hz) INPUT VOLTAGE AND CURRENT NOISE SPECTRAL DENSITY vs FREQUENCY CHANNEL SEPARATION vs FREQUENCY 140 10k 100k 1k Current Noise 100 1k Voltage Noise 100 10 10 1 Current Noise (fAHz) Voltage Noise (nVHz) 10k Channel Separation (dB) 130 120 110 100 90 80 70 1 10 100 1k 10k 100k 1M Dual and quad devices. 60 0.1 10M 10 100 TOTAL HARMONIC DISTORTION + NOISE vs FREQUENCY 0.01 G = 10, 3VPP (VO = 1V to 4V) Harmonic Distortion (%) THD+N (%) RL = 600 G = 100, 3VPP (VO = 1V to 4V) G = 1, 3VPP (VO = 1V to 4V) Input goes through transition region 0.001 G = 1, 2.5VPP (VO = 0.25V to 2.75V) Input does NOT go through transition region 100 1k Frequency (Hz) 100k 1M 10M 10k 0.1 (-60dBc) G=1 VO = 2.5VPP RL = 600 0.01 (-80dBc) 0.001 (-100dBc) 3rd-Harmonic 2nd-Harmonic 0.0001 10 10k HARMONIC DISTORTION + NOISE vs FREQUENCY 1 (-40dBc) 1 0.1 1k Frequency (Hz) Frequency (Hz) 100k 0.0001 (-120dBc) 1k 10k 100k 1M Frequency (Hz) 5 "#$ %"#$ &"#$ www.ti.com SBOS099C - SEPTEMBER 2000 - REVISED JANUARY 2005 TYPICAL CHARACTERISTICS (continued) All specifications at TA = +25C, VS = +5V, and RL = 1k connected to VS/2, unless otherwise noted. OPEN-LOOP GAIN vs TEMPERATURE DIFFERENTIAL GAIN/PHASE vs RESISTIVE LOAD 130 0.5 Open-Loop Gain (dB) 0.4 Differential Gain (%) Differential Phase (_) G=2 VO = 1.4V NTSC Signal Generator See Figure 6 for test circuit. Phase 0.3 0.2 Gain 125 RL = 1k RL = 10k 120 RL = 600 115 0.1 110 0 0 100 200 300 400 500 600 -75 700 800 900 1000 -50 -25 Resistive Load ( ) 50 75 100 125 40 35 90 CMRR, VS = 2.7V (VCM = -0.1V to +2.8V) PSRR 70 Slew Rate (V/s) 30 100 PSRR (dB) 90 CMRR (dB) 25 SLEW RATE vs TEMPERATURE COMMON-MODE AND POWER-SUPPLY REJECTION RATIO vs TEMPERATURE 100 110 CMRR, VS = 5.5V (VCM = -0.1V to +5.6V) 80 0 Temperature (_ C) Negative Slew Rate 25 Positive Slew Rate 20 15 10 80 5 60 -75 -50 -25 0 25 50 75 100 0 70 125 -75 -50 -25 100 6 -ISC 80 5.5 70 IQ 60 4.5 50 4.0 40 30 0 25 50 Temperature (_C) 75 100 125 Quiescent Current (mA) 90 -25 100 125 5.5 Short-Circuit Current (mA) Quiescent Current (mA) 6.5 -50 75 Per Amplifier +ISC 3.5 -75 50 6.0 7.0 5.0 25 QUIESCENT CURRENT vs SUPPLY VOLTAGE QUIESCENT CURRENT AND SHORT-CIRCUIT CURRENT vs TEMPERATURE 6.0 0 Temperature (_C) Temperature (_C) 5.0 4.5 4.0 3.5 3.0 2.0 2.5 3.0 3.5 4.0 Supply Voltage (V) 4.5 5.0 5.5 "#$ %"#$ &"#$ www.ti.com SBOS099C - SEPTEMBER 2000 - REVISED JANUARY 2005 TYPICAL CHARACTERISTICS (continued) All specifications at TA = +25C, VS = +5V, and RL = 1k connected to VS/2, unless otherwise noted. INPUT BIAS CURRENT vs INPUT COMMON-MODE VOLTAGE INPUT BIAS CURRENT vs TEMPERATURE 1.5 100 1.0 Input Bias Current (pA) Input Bias Current (pA) 1k 10 1 -50 -25 0 25 50 Temperature (_ C) 75 100 0.0 -0.5 -0.5 0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 0.1 -75 0.5 125 Common-Mode Voltage (V) MAXIMUM OUTPUT VOLTAGE vs FREQUENCY 6 10 5 Output Voltage (VPP) Output Impedance () CLOSED-LOOP OUTPUT IMPEDANCE vs FREQUENCY 100 1 0.1 G = 100 0.01 G = 10 0.001 G=1 10 Maximum output voltage without slew rate-induced distortion. 4 VS = 2.7V 3 2 1 0 100k 0.0001 1 VS = 5.5V 100 1k 10k 100k 1M 10M 100M 1M Frequency (Hz) 100M OPEN-LOOP GAIN vs OUTPUT VOLTAGE SWING OUTPUT VOLTAGE SWING vs OUTPUT CURRENT 140 V+ -55_C +125_ C (V+)-2 Open-Loop Gain (dB) (V+)-1 +25_C Depending on circuit configuration (including closed-loop gain) performance may be degraded in shaded region. (V-)+2 -55_C +25_C +125_C (V-)+1 I OUT = 2.5mA IOUT = 250A 130 Output Voltage (V) 10M Frequency (Hz) 120 110 IOUT = 4.2mA 100 90 80 70 60 (V-) 0 10 20 Output Current (mA) 30 40 0 20 40 60 80 100 120 140 160 180 200 Output Voltage Swing from Rails (mV) 7 "#$ %"#$ &"#$ www.ti.com SBOS099C - SEPTEMBER 2000 - REVISED JANUARY 2005 TYPICAL CHARACTERISTICS (continued) All specifications at TA = +25C, VS = +5V, and RL = 1k connected to VS/2, unless otherwise noted. OFFSET VOLTAGE PRODUCTION DISTRIBUTION 18 20 Typical distribution of packaged units. 16 Typical production distribution of packaged units. 18 14 16 Percent of Amplifiers (%) Percent of Amplifiers (%) OFFSET VOLTAGE DRIFT PRODUCTION DISTRIBUTION 12 10 8 6 4 14 12 10 8 6 4 2 2 0 -500 -450 -400 -350 -300 -250 -200 -150 -100 -50 0 50 100 150 200 250 300 350 400 450 500 0 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Offset Voltage Drift (V/_C) Offset Voltage (V) SETTLING TIME vs CLOSED-LOOP GAIN SMALL-SIGNAL OVERSHOOT vs LOAD CAPACITANCE 10 80 70 G=1 50 Settling Time (s) Overshoot (%) 60 G = -1 40 30 G = 10 20 0.01% 1 10 0.1% 0.1 0 10 100 1k 10k 100k -1 1M Load Capacitance (pF) LARGE-SIGNAL STEP RESPONSE CL = 100pF 1V/div 50mV/div SMALL-SIGNAL STEP RESPONSE CL = 100pF 100ns/div 8 -10 Closed-Loop Gain (V/V) 200ns/div -100 "#$ %"#$ &"#$ www.ti.com SBOS099C - SEPTEMBER 2000 - REVISED JANUARY 2005 APPLICATIONS INFORMATION OPA350 series op amps are fabricated on a state-of-the-art 0.6 micron CMOS process. They are unity-gain stable and suitable for a wide range of general-purpose applications. Rail-to-rail input/output make them ideal for driving sampling A/D converters. They are also well-suited for controlling the output power in cell phones. These applications often require high speed and low noise. In addition, the OPA350 series offers a low-cost solution for general-purpose and consumer video applications (75 drive capability). Excellent ac performance makes the OPA350 series well-suited for audio applications. Their bandwidth, slew rate, low noise (5nV/Hz), low THD (0.0006%), and small package options are ideal for these applications. The class AB output stage is capable of driving 600 loads connected to any point between V+ and ground. Rail-to-rail input and output swing significantly increases dynamic range, especially in low voltage supply applications. Figure 1 shows the input and output waveforms for the OPA350 in unity-gain configuration. Operation is from a single +5V supply with a 1k load connected to VS/2. The input is a 5VPP sinusoid. Output voltage swing is approximately 4.95VPP. Power supply pins should be bypassed with 0.01F ceramic capacitors. VS = +5, G = +1, RL = 1k 5V 1.25V/div VIN 0 5V VOUT 0 Figure 1. Rail-to-Rail Input and Output OPERATING VOLTAGE OPA350 series op amps are fully specified from +2.7V to +5.5V. However, supply voltage may range from +2.5V to +5.5V. Parameters are tested over the specified supply range--a unique feature of the OPA350 series. In addition, many specifications apply from -40C to +85C. Most behavior remains virtually unchanged throughout the full operating voltage range. Parameters that vary significantly with operating voltage or temperature are shown in the typical characteristics. RAIL-TO-RAIL INPUT The tested input common-mode voltage range of the OPA350 series extends 100mV beyond the supply rails. This is achieved with a complementary input stage--an N-channel input differential pair in parallel with a P-channel differential pair, as shown in Figure 2. The N-channel pair is active for input voltages close to the positive rail, typically (V+) - 1.8V to 100mV above the positive supply, while the P-channel pair is on for inputs from 100mV below the negative supply to approximately (V+) - 1.8V. There is a small transition region, typically (V+) - 2V to (V+) - 1.6V, in which both pairs are on. This 400mV transition region can vary 400mV with process variation. Thus, the transition region (both input stages on) can range from (V+) - 2.4V to (V+) - 2.0V on the low end, up to (V+) - 1.6V to (V+) - 1.2V on the high end. OPA350 series op amps are laser-trimmed to reduce offset voltage difference between the N-channel and P-channel input stages, resulting in improved common-mode rejection and a smooth transition between the N-channel pair and the P-channel pair. However, within the 400mV transition region PSRR, CMRR, offset voltage, offset drift, and THD may be degraded compared to operation outside this region. A double-folded cascode adds the signal from the two input pairs and presents a differential signal to the class AB output stage. Normally, input bias current is approximately 500fA. However, large inputs (greater than 300mV beyond the supply rails) can turn on the OPA350's input protection diodes, causing excessive current to flow in or out of the input pins. Momentary voltages greater than 300mV beyond the power supply can be tolerated if the current on the input pins is limited to 10mA. This is easily accomplished with an input resistor, as shown in Figure 3. Many input signals are inherently current-limited to less than 10mA; therefore, a limiting resistor is not required. 9 "#$ %"#$ &"#$ www.ti.com SBOS099C - SEPTEMBER 2000 - REVISED JANUARY 2005 V+ Reference Current VIN+ VIN- VBIAS1 Class AB Control Circuitry VO VBIAS2 V- (Ground) Figure 2. Simplified Schematic within a few tens of millivolts from the supply rails and maintain high open-loop gain. See the typical characteristics Output Voltage Swing vs Output Current and Open-Loop Gain vs Output Voltage. CAPACITIVE LOAD AND STABILITY V+ IOVERLOAD 10mA max OPAx350 VOUT VIN 5k Figure 3. Input Current Protection for Voltages Exceeding the Supply Voltage RAIL-TO-RAIL OUTPUT A class AB output stage with common-source transistors is used to achieve rail-to-rail output. For light resistive loads (>10k), the output voltage swing is typically ten millivolts from the supply rails. With heavier resistive loads (600 to 10k), the output can swing to 10 OPA350 series op amps can drive a wide range of capacitive loads. However, all op amps under certain conditions may become unstable. Op amp configuration, gain, and load value are just a few of the factors to consider when determining stability. An op amp in unity-gain configuration is the most susceptible to the effects of capacitive load. The capacitive load reacts with the op amp's output impedance, along with any additional load resistance, to create a pole in the small-signal response that degrades the phase margin. In unity gain, OPA350 series op amps perform well with very large capacitive loads. Increasing gain enhances the amplifier's ability to drive more capacitance. The typical characteristic Small-Signal Overshoot vs Capacitive Load shows performance with a 1k resistive load. Increasing load resistance improves capacitive load drive capability. "#$ %"#$ &"#$ www.ti.com SBOS099C - SEPTEMBER 2000 - REVISED JANUARY 2005 FEEDBACK CAPACITOR IMPROVES RESPONSE For optimum settling time and stability with high-impedance feedback networks, it may be necessary to add a feedback capacitor across the feedback resistor, RF, as shown in Figure 4. This capacitor compensates for the zero created by the feedback network impedance and the OPA350's input capacitance (and any parasitic layout capacitance). The effect becomes more significant with higher impedance networks. series provides an effective means of buffering the A/D's input capacitance and resulting charge injection while providing signal gain. Figure 5 shows the OPA350 driving an ADS7861. The ADS7861 is a dual, 500kHz, 12-bit sampling converter in the tiny SSOP-24 package. When used with the miniature package options of the OPA350 series, the combination is ideal for space-limited applications. For further information, consult the ADS7861 data sheet (SBAS110A). OUTPUT IMPEDANCE CF R IN RF VIN V+ CIN RIN * CIN = RF * CF VOUT O PA350 CL CIN Where CIN is equal to the OPA350's input capacitance (approximately 9pF) plus any parasitic layout capacitance. Figure 4. Feedback Capacitor Improves Dynamic Performance It is suggested that a variable capacitor be used for the feedback capacitor since input capacitance may vary between op amps and layout capacitance is difficult to determine. For the circuit shown in Figure 4, the value of the variable feedback capacitor should be chosen so that the input resistance times the input capacitance of the OPA350 (typically 9pF) plus the estimated parasitic layout capacitance equals the feedback capacitor times the feedback resistor: R IN @ C IN + RF @ CF where CIN is equal to the OPA350's input capacitance (sum of differential and common-mode) plus the layout capacitance. The capacitor can be varied until optimum performance is obtained. DRIVING A/D CONVERTERS OPA350 series op amps are optimized for driving medium speed (up to 500kHz) sampling A/D converters. However, they also offer excellent performance for higher speed converters. The OPA350 The low frequency open-loop output impedance of the OPA350's common-source output stage is approximately 1k. When the op amp is connected with feedback, this value is reduced significantly by the loop gain of the op amp. For example, with 122dB of open-loop gain, the output impedance is reduced in unity-gain to less than 0.001. For each decade rise in the closed-loop gain, the loop gain is reduced by the same amount which results in a ten-fold increase in effective output impedance (see the typical characteristic, Output Impedance vs Frequency). At higher frequencies, the output impedance will rise as the open-loop gain of the op amp drops. However, at these frequencies the output also becomes capacitive due to parasitic capacitance. This prevents the output impedance from becoming too high, which can cause stability problems when driving capacitive loads. As mentioned previously, the OPA350 has excellent capacitive load drive capability for an op amp with its bandwidth. VIDEO LINE DRIVER Figure 6 shows a circuit for a single supply, G = 2 composite video line driver. The synchronized outputs of a composite video line driver extend below ground. As shown, the input to the op amp should be ac-coupled and shifted positively to provide adequate signal swing to account for these negative signals in a single-supply configuration. The input is terminated with a 75 resistor and ac-coupled with a 47F capacitor to a voltage divider that provides the dc bias point to the input. In Figure 6, this point is approximately (V-) + 1.7V. Setting the optimal bias point requires some understanding of the nature of composite video signals. For best performance, one should be careful to avoid the distortion caused by the transition region of the OPA350's complementary input stage. Refer to the discussion of rail-to-rail input. 11 "#$ %"#$ &"#$ www.ti.com SBOS099C - SEPTEMBER 2000 - REVISED JANUARY 2005 CB1 2 4 1 1/ 4 3 VIN B1 +5V 2k 2k O P A 43 5 0 0.1F 0.1F CB0 24 2k 2k 2 3 6 7 1/ 4 5 VIN B0 4 O P A 43 5 0 5 6 CA1 7 2k 2k 8 9 9 8 1/ 4 10 VIN A1 13 +VD O P A 43 5 0 10 11 CA0 +VA CH B1+ SERIAL DATA A CH B1- SERIAL DATA B CH B0+ BUSY CH B0- CLOCK CH A1+ CS CH A1- ADS7861 RD CH A0+ CONVST CH A0- A0 REFIN M0 REFOUT M1 DGND 1 AGND 12 2k 2k 12 14 1/ 4 VIN A0 13 O P A 43 5 0 11 VIN = 0V to 2.45V for 0V to 4.9V output. Choose CB1, CB0, CA1, CA0 to filter high frequency noise. Figure 5. OPA4350 Driving Sampling A/D Converter 12 23 22 21 20 19 18 17 16 15 14 Serial Interface "#$ %"#$ &"#$ www.ti.com SBOS099C - SEPTEMBER 2000 - REVISED JANUARY 2005 RF 1k RG 1k +5V C1 220F C4 0.1F 0.1F 2 + 10F 7 C5 1000F 6 C2 47F Video In ROUT Cable VOUT OPA350 RL 3 R1 75 4 R2 5k R3 5k R4 5k +5V (pin 7) C3 10F Figure 6. Single-Supply Video Line Driver +5V 50k (2.5V) 8 RG REF1004-2.5 4 R1 100k R2 25k +5V 1/ 2 R3 25k R4 100k O P A 2 35 0 1/ 2 VO O P A 23 5 0 G=5+ 200k RG RL 10k Figure 7. Two Op-Amp Instrumentation Amplifier With Improved High Frequency Common-Mode Rejection 13 "#$ %"#$ &"#$ www.ti.com SBOS099C - SEPTEMBER 2000 - REVISED JANUARY 2005 R1 10.5k C1 4.7nF +2.5V +2.5V R1 2.74k R2 19.6k RL 20k VIN C2 1nF -2.5V Figure 8. 10kHz Low-Pass Filter 14 C1 1830pF VOUT OPA350 C2 270pF VOUT OPA350 RL 20k VIN R2 49.9k -2.5V Figure 9. 10kHz High-Pass Filter PACKAGE OPTION ADDENDUM www.ti.com 16-Aug-2012 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Drawing Pins Package Qty Eco Plan (2) Lead/ Ball Finish MSL Peak Temp (3) OPA2350EA/250 ACTIVE VSSOP DGK 8 250 Green (RoHS & no Sb/Br) CU NIPDAUAGLevel-2-260C-1 YEAR OPA2350EA/250G4 ACTIVE VSSOP DGK 8 250 Green (RoHS & no Sb/Br) CU NIPDAUAGLevel-2-260C-1 YEAR OPA2350EA/2K5 ACTIVE VSSOP DGK 8 2500 Green (RoHS & no Sb/Br) CU NIPDAUAGLevel-2-260C-1 YEAR OPA2350EA/2K5G4 ACTIVE VSSOP DGK 8 2500 Green (RoHS & no Sb/Br) CU NIPDAUAGLevel-2-260C-1 YEAR OPA2350PA ACTIVE PDIP P 8 50 Green (RoHS & no Sb/Br) CU NIPDAU N / A for Pkg Type OPA2350PAG4 ACTIVE PDIP P 8 50 Green (RoHS & no Sb/Br) CU NIPDAU N / A for Pkg Type OPA2350UA ACTIVE SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR OPA2350UA/2K5 ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR OPA2350UA/2K5G4 ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR OPA2350UAG4 ACTIVE SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR OPA350EA/250 ACTIVE VSSOP DGK 8 250 Green (RoHS & no Sb/Br) CU NIPDAUAGLevel-2-260C-1 YEAR OPA350EA/250G4 ACTIVE VSSOP DGK 8 250 Green (RoHS & no Sb/Br) CU NIPDAUAGLevel-2-260C-1 YEAR OPA350EA/2K5 ACTIVE VSSOP DGK 8 2500 Green (RoHS & no Sb/Br) CU NIPDAUAGLevel-2-260C-1 YEAR OPA350EA/2K5G4 ACTIVE VSSOP DGK 8 2500 Green (RoHS & no Sb/Br) CU NIPDAUAGLevel-2-260C-1 YEAR OPA350PA ACTIVE PDIP P 8 50 Green (RoHS & no Sb/Br) CU NIPDAU N / A for Pkg Type OPA350PAG4 ACTIVE PDIP P 8 50 Green (RoHS & no Sb/Br) CU NIPDAU N / A for Pkg Type OPA350UA ACTIVE SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR Addendum-Page 1 Samples (Requires Login) PACKAGE OPTION ADDENDUM www.ti.com Orderable Device 16-Aug-2012 Status (1) Package Type Package Drawing Pins Package Qty Eco Plan (2) Lead/ Ball Finish MSL Peak Temp (3) OPA350UA/2K5 ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR OPA350UA/2K5G4 ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR OPA350UAG4 ACTIVE SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR OPA4350EA/250 ACTIVE SSOP DBQ 16 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR OPA4350EA/250G4 ACTIVE SSOP DBQ 16 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR OPA4350EA/2K5 ACTIVE SSOP DBQ 16 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR OPA4350EA/2K5G4 ACTIVE SSOP DBQ 16 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR OPA4350UA ACTIVE SOIC D 14 50 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR OPA4350UA/2K5 ACTIVE SOIC D 14 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR OPA4350UA/2K5G4 ACTIVE SOIC D 14 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR OPA4350UAG4 ACTIVE SOIC D 14 50 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR Samples (Requires Login) (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Addendum-Page 2 PACKAGE OPTION ADDENDUM www.ti.com 16-Aug-2012 Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 3 PACKAGE MATERIALS INFORMATION www.ti.com 16-Aug-2012 TAPE AND REEL INFORMATION *All dimensions are nominal Device Package Package Pins Type Drawing SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant OPA2350EA/250 VSSOP DGK 8 250 180.0 12.4 5.3 3.4 1.4 8.0 12.0 Q1 OPA2350EA/2K5 VSSOP DGK 8 2500 330.0 12.4 5.3 3.4 1.4 8.0 12.0 Q1 OPA2350UA/2K5 SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1 OPA350EA/250 VSSOP DGK 8 250 180.0 12.4 5.3 3.4 1.4 8.0 12.0 Q1 OPA350EA/2K5 VSSOP DGK 8 2500 330.0 12.4 5.3 3.4 1.4 8.0 12.0 Q1 OPA350UA/2K5 SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1 OPA4350EA/250 SSOP DBQ 16 250 180.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1 OPA4350EA/2K5 SSOP DBQ 16 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1 OPA4350UA/2K5 SOIC D 14 2500 330.0 16.4 6.5 9.0 2.1 8.0 16.0 Q1 Pack Materials-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 16-Aug-2012 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) OPA2350EA/250 VSSOP DGK OPA2350EA/2K5 VSSOP DGK 8 250 210.0 185.0 35.0 8 2500 367.0 367.0 35.0 OPA2350UA/2K5 SOIC D 8 2500 367.0 367.0 35.0 OPA350EA/250 VSSOP DGK 8 250 210.0 185.0 35.0 OPA350EA/2K5 VSSOP DGK 8 2500 367.0 367.0 35.0 OPA350UA/2K5 SOIC D 8 2500 367.0 367.0 35.0 OPA4350EA/250 SSOP DBQ 16 250 210.0 185.0 35.0 OPA4350EA/2K5 SSOP DBQ 16 2500 367.0 367.0 35.0 OPA4350UA/2K5 SOIC D 14 2500 367.0 367.0 38.0 Pack Materials-Page 2 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All semiconductor products (also referred to herein as "components") are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI's terms and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily performed. TI assumes no liability for applications assistance or the design of Buyers' products. Buyers are responsible for their products and applications using TI components. To minimize the risks associated with Buyers' products and applications, Buyers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use of any TI components in safety-critical applications. In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI's goal is to help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and requirements. Nonetheless, such components are subject to these terms. No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties have executed a special agreement specifically governing such use. Only those TI components which TI has specifically designated as military grade or "enhanced plastic" are designed and intended for use in military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI has specifically designated certain components which meet ISO/TS16949 requirements, mainly for automotive use. Components which have not been so designated are neither designed nor intended for automotive use; and TI will not be responsible for any failure of such components to meet such requirements. Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP(R) Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Applications Processors www.ti.com/omap TI E2E Community e2e.ti.com Wireless Connectivity www.ti.com/wirelessconnectivity Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2012, Texas Instruments Incorporated