CAT.8100R
Wider range of rating.
4 6.3 10
0G 0J 1A
4.7 475 M
10 106 M
22 226 M
V
F98
Specifications
Type numbering system (Example : 6.3V 10 µF)
Drawing
LW1S2
W2HS1
M1.6 ± 0.1 0.85 ± 0.1 0.65 ± 0.1 0.8 ± 0.1 0.5 ± 0.1
0.6
±
0.1
(
mm
)
Cace Code
L
H
W1
W2
S1S2S1
Rated voltage
(Voltage code)
J
Taping code
(Refer to page 211 for details)
F
19
28
30
4J
51
60
76
8M
9M
10 11
Case code
Capacitance tolerance
Rated Capacitance Rated voltage
Series
Marking
Standard ratings
Cap.
(
µ
F)
Code
Category
Temperature Range
Capacitance Tolerance
Leakage Current
Dissipation Factor(120Hz)
Damp Heat
Temperature Cycles
Resistance to Soldening
Heat
Surge∗
Endurance∗
Shear Test
Terminal Strength
Performance Characteristics
± 20% (at 120Hz)
4.7µF 6%
10µF 8%
22µF 15%
After 5 minute's application of rated voltage, leakage current at
20°C is not more than 0.1CV or 0.5µA, whichever is greater.
At 40°C, 90 ~ 95% R.H., For 500hours (No voltage applied)
Capacitance Change Within ±30% of initial value
Dissipation Factor 150%
or less of initial specified value
Leakage Current 200%
or less of initial specified value
At --55°C / +125°C, For 30 minutes each, 5 cycles
Capacitance Change Within ±30% of initial value
Dissipation Factor 150%
or less of initial specified value
Leakage Current Initial specified value or less
At 240°C, For 10 seconds, Reflow,
Capacitance Change Within ±30% of initial value
Leakage Current Initial specified value or less
Leakage Current Initial specified value or less
After application of surge in series with a 1kΩ resistor at the
rate of 30 seconds ON, 30 seconds OFF, for 1000 successive
test cycles at 85°C, capacitors meet the characteristics
requirements listed below.
Capacitance Change Within ±30
%
initial value
Dissipation Factor 150
%
or less of initial specified value
Leakage Current 200
%
or less of initial specified value
After 1000 hours' application of rated voltage in series with a
3Ω resistor at 85°C, capacitors meet the characteristic
requirements listed below
Capacitance Change Within ±30% of initial value
Dissipation Factor 150
%
or less of initial specified value
Leakage Current 200
%
or less of initial specified value
After applying the pressure load of 5N
for 10±1 seconds horizontally to the
center of capacitor side body which has
no electrode and has been soldered
beforehand on an aluminum substrate,
there shall be found neither exfoliation
nor its sign at the terminal electrode.
Keeping a capacitor surface-mounted on a substrate upside
down and supporting the substrate at both of the opposite
bottom points 45mm apart from the center of the capacitor, the
pressure strength is applied with
a specified jig at the center of the
substrate so that the substrate
may bend by 1mm as illustrated.
Then, there shall be found no
remarkable abnormality on the
capacitor terminals.
Item
-- 55 ~ +125°C (Rated temperature : 85°C)
5N (0.51kg • f)
For 10 ± 1seconds
20
R230
45 45
1
mm
Face down Terminals Chip,
∗As for the surge and derated voltage at 125
˚C
, refer to page 210 for details.
SOLID TANTALUM ELECTROLYTIC CAPACITORS
