S Series Vishay Foil Resistors High Precision Foil Resistor with TCR of 2.0 ppm/C, Tolerance of 0.005 % and Load Life Stability of 0.005 % FEATURES INTRODUCTION Bulk Metal(R) Foil (BMF) technology outperforms all other resistor technologies available today for applications that require high precision and high stability. This technology has been pioneered and developed by VISHAY, and products based on this technology are the most suitable for a wide range of applications. BMF technology allows us to produce customer orientated products, designed to satisfy challenging and specific technical requirements. Model S series made from Vishay BMF offers low TCR, excellent load life stability, tight tolerance, fast response time, low current noise, low thermal EMF and low voltage coefficient, all in one resistor. The S series is virtually insensitive to destabillizing factors. The resistor element is a solid alloy that displays the desirable bulk properties of its parent material, thus it is inherently stable and noise free. Vishay's Bulk Metal(R) S series resistors are the modern generation of precision resistors. The standard design of these resistors provides a unique combination of characteristics found in no other single resistor. Our application engineering department is available to advise and to make recommendations. For non-standard technical requirements and special applications, please contact us. * Temperature coefficient of resistance (TCR): - 55 C to + 125 C, 25 C ref. - S102C series: 2 ppm/C typical (see table 1) - S102K series: 1 ppm/C typical (see table 1) * Rated power: to 1 W at + 125 C * Tolerance: 0.005 % (50 ppm) * Load life stability: to 0.005 % at 70 C, 2000 h at rated power * Resistance range: 0.5 to 1 M (higher or lower values of resistance are available) * Vishay Foil resistors are not restricted to standard values; specific "as required" values can be supplied at no extra cost or delivery (e.g. 1K2345 vs. 1K) * Electrostatic discharge up to 25 000 V * Non inductive, non capacitive design * Rise time: 1 ns effectively no ringing * Current noise: 0.010 VRMS/V of applied voltage (< - 40 dB) * Thermal EMF: 0.05 V/C typical * Voltage coefficient: < 0.1 ppm/V * Low inductance: < 0.08 H typical * Non hot spot design * Terminal finish: lead (Pb)-free or tin/lead alloy * Matched sets are available per request (TCR tracking: to 0.5 ppm/C) * Prototype quantities available in just 5 working days or sooner. For more information, please contact foil@vishay.com * For better TCR and PCR performances please review the Z201 datasheet APPLICATIONS * * * * * * * High precision amplifiers Down-hole (high temperature) High precision instrumentation Medical and test equipment Industrial Audio (high end stereo equipment) EB applications (electron beam scanning and recording equipment, electron microscopes) * Military, airborne * Measurement instrumentation TABLE 1 - RESISTANCE VERSUS TCR (- 55 C to + 125 C, + 25 C ref.) FIGURE 1 - FOIL RESISTOR TCR COMPARISON OF FOIL ALLOYS IN MILITARY RANGE + 150 RESISTANCE VALUE () TYPICAL TCR AND MAX SPREAD (ppm/C) S102(C) 80 to < 150K 2 2.5 S102(K) 80 to < 100K 1 2.5 - 50 2 3.5 - 100 RESISTOR S102(C) S102(K) S102(C) S102(K) 50 to < 80 1 to < 50 1 3.5 2 4.5 1 4.5 + 100 R 1 ppm/ C + 50 0 R (ppm) 2 ppm/ C - 150 - 200 - 50 - 55 - 25 C Alloy 2 ppm/ C 0 + 25 K Alloy 1 ppm/ C + 50 + 75 + 100 + 125 Temperature (C) * Pb containing terminations are not RoHS compliant, exemptions may apply Document Number: 63001 Revision: 25-Jun-09 For any questions, contact: foil@vishay.com www.vishay.com 1 S Series Vishay Foil Resistors FIGURE 2 - STANDARD IMPRINTING AND DIMENSIONS Front View L H VISHAY XXXX S102C W Rear View Optional Customer Part Number Print specification, etc. if required Date Code 01 10 Year Week XXXXXX 100R01 0.01 % Resistance Value Code Tolerance ST1) SW Model Number LS LL Lead Material #22 AWG Round Solder Coated Copper Note 1. The standoffs shall be so located as to give a lead clearance of 0.010" minimum between the resistor body and the printed circuit board when the standoffs are seated on the printed circuit board. This is to allow for proper cleaning of flux and other contaminants from the unit after all soldering processes. TABLE 2 - MODEL SELECTION MODEL NUMBER AMBIENT RESISTANCE MAXIMUM POWER RATING AVERAGE WEIGHT RANGE WORKING IN GRAMS () VOLTAGE at at + 70 C + 125 C S102C (S102J) (2) 1 to 150K S102K (S102L) (2) 1 to 100K S104D (S104F) (1) 1 to 500K S104K 1 to 300K S105D (S105F) (1) 1 to 750K S105K 1 to 500K S106D 0.5 to 1M S106K 0.5 to 600K 300 0.6 W 0.3 W up to 100K 0.4 W 0.2 W 0.6 over 100K 350 1.0 W 0.5 W up to 200K 0.6 W 0.3 W 1.4 over 200K 350 1.5 W 0.75 W up to 300K 0.8 W 0.4 W 1.9 over 300K 500 2.0 W 1.0 W up to 400K 1.0 W 0.5 W over 400K 4.0 DIMENSIONS INCHES W: 0.105 0.010 L: 0.300 0.010 H: 0.326 0.010 ST: 0.010 min. SW: 0.035 0.010 LL: 1.000 0.125 LS: 0.150 0.0054 W: 0.160 max. L: 0.575 max. H: 0.413 max. ST: 0.035 0.005 SW: 0.050 0.005 LL: 1.000 0.125 LS: 0.400 0.020 W: 0.160 max. L: 0.820 max. H: 0.413 max. ST: 0.035 0.005 SW: 0.050 0.005 LL: 1.000 0.125 LS: 0.650 0.020 W: 0.260 max. L: 1.200 max. H: 0.413 max. ST: 0.035 0.005 SW: 0.050 0.005 LL: 1.000 0.125 LS: 0.900 0.020 mm F (1) (INCHES) 2.67 0.25 7.62 0.25 8.28 0.25 0.254 min. 1.02 0.13 25.4 3.18 3.81 0.13 4.06 max. 14.61 max. (0.138) 10.49 max. (0.565) 0.889 0.13 (0.413) 1.27 0.13 25.4 3.18 10.16 0.51 (0.138) 4.06 max. (0.890) 20.83 max. (0.413) 10.49 max. 0.889 0.13 1.27 0.13 25.4 3.18 16.51 0.51 (0.7 0.05) 6.60 max. 30.48 max. 10.49 max. 0.889 0.13 1.27 0.13 25.4 3.18 22.86 0.51 TIGHTEST TOLERANCE VS. LOWEST RESISTANCE VALUE 0.005 %/50 0.01 %/25 0.02 %/12 0.05 %/5 0.1 %/2 0.50 %/1 Notes (1) S104F and S105F have different package dimensions (see last column). All other specifications are the same. (2) 0.200" (5.08 mm) lead spacing available - specify S102J for S102C, and S102L for S102K. www.vishay.com 2 For any questions, contact: foil@vishay.com Document Number: 63001 Revision: 25-Jun-09 S Series Vishay Foil Resistors FIGURE 4 - TRIMMING TO VALUES (conceptual illustration) FIGURE 3 - POWER DERATING CURVE Percent of Rated Power at + 70 C 100 % - 55 C + 70 C Rated Power 75 % Current Path Before Trimming Interloop Capacitance Reduction in Series Current Path After Trimming Trimming Process Removes this Material from Shorting Strip Area Changing Current Path and Increasing Resistance 50 % Recommended operation for < 150 ppm R after 2000 h load life 25 % 0 - 75 Mutual Inductance Reduction due to Change in Current Direction - 50 - 25 0 + 25 + 50 + 75 + 100 + 125 + 150 + 175 + 200 Ambient Temperature (C) Note: Foil shown in black, etched spaces in white TABLE 3 - ENVIRONMENTAL PERFORMANCE COMPARISON MIL-PRF-55182 CHAR J S-SERIES MAXIMUM R S-SERIES TYPICAL R Thermal shock, 5 x (- 65 C to + 150 C) 0.2 % 0.01 % (100 ppm) 0.002 % (20 ppm) Short time overload, 6.25 x rated power 0.2 % 0.01 % (100 ppm) 0.003 % (30 ppm) 25 ppm/C 4.5 ppm/C 2.0 ppm/C Low temperature storage (24 h at - 65 C) 0.15 % 0.01 % (100 ppm) 0.002 % (20 ppm) Low temperature operation (45 min, rated power at - 65 C) 0.15 % 0.01 % (100 ppm) 0.002 % (20 ppm) Terminal strength 0.2 % 0.01 % (100 ppm) 0.002 % (20 ppm) Test Group I Test Group II Resistance temperature characteristics Characteristic Test Group III DWV 0.15 % 0.01 % (100 ppm) 0.002 % (20 ppm) Resistance to solder heat 0.1 % 0.01 % (100 ppm) 0.005 % (50 ppm) Moisture resistance 0.4 % 0.05 % (500 ppm) 0.01 % (100 ppm) Shock 0.2 % 0.01 % (100 ppm) 0.002 % (20 ppm) Vibration 0.2 % 0.01 % (100 ppm) 0.002 % (20 ppm) 2000 h 0.5 % 0.015 % (150 ppm) 0.01 % (100 ppm) 10 000 h 2.0 % 0.05 % (500 ppm) 0.03 % (300 ppm) 0.5 % 0.015 % (150 ppm) 0.01 % (100 ppm) 2.0 % 0.1 % (1000 ppm) 0.05 % (500 ppm) 5 ppm/V < 0.1 ppm/V < 0.1 ppm/V Test Group IV Test Group V Life test at 0.3 W/+ 125 C Test Group Va Life test at 0.6 W (2 x rated power)/+ 70 C, 2000 h Test Group VI High temperature exposure (2000 h at + 175 C) Test Group VII Voltage coefficient Document Number: 63001 Revision: 25-Jun-09 For any questions, contact: foil@vishay.com www.vishay.com 3 S Series Vishay Foil Resistors STANDARD OPERATIONS AND TEST CONDITIONS IMPROVED PERFORMANCE TESTING (IPT) A. Standard Test Operations: The preceding information is based on product directly off the production line. Improved performance (meaning increased time stability with load and other stresses) is available through factory conducted "Improved Performance Testing". The test routine is usually tailored to the users stability objectives and product that has been screened can be brought down to a potential load life of less than 50 ppm. By 100 % Inspection * Short-time overload (6.25 x rated power for 5 s) * Resistance - tolerance check * Visual and mechanical By Sample Inspection * TCR * Environmental tests per table 3 on a quarterly basis to establish performance by similarity B. Standard Test Conditions: * Lead test point: 0.5" (12.7 mm) from resistor body * Temperature: + 23 C 2 C * Relative humidity: per MIL-STD-202 Various screen test routines are available and all anticipated stresses must be taken into account before settling on one specific test routine. Our applications engineering department is prepared to discuss and recommend appropriate routines given the full spectrum of anticipated stresses and stability requirements. TABLE 4 - "S" SERIES SPECIFICATIONS Stability (1) Load life at 2000 h Load life at 10 000 h Current Noise 0.015 % (150 ppm) Maximum R at 0.3 W/+ 125 C 0.005 % (50 ppm) Maximum R at 0.1 W/+ 70 C 0.05 % (500 ppm) Maximum R at 0.3 W/+ 125 C 0.01 % (100 ppm) Maximum R at 0.05 W/+ 125 C 0.010 V (RMS)/V of applied voltage (- 40 dB) High Frequency Operation Rise time 1.0 ns at 1 k Inductance (L) (2) 0.1 H maximum; 0.08 H typical Capacitance (C) 1.0 pF maximum; 0.5 pF typical Voltage Coefficient < 0.1 ppm/V (3) Thermal EMF (4) 0.1 V/C Maximum; 0.05 V/C typical 1 V/W (Model S102C) Notes (1) Load life R maximum can be reduced by 80 %, please contact applications engineering department. (2) Inductance (L) due mainly to the leads. (3) The resolution limit of existing test equipment (within the measurement capability of the equipment, or "essentially zero".) (4) V/C relates to EMF due to lead temperature difference and V/watt due to power applied to the resistor. www.vishay.com 4 For any questions, contact: foil@vishay.com Document Number: 63001 Revision: 25-Jun-09 S Series Vishay Foil Resistors TABLE 5 - GLOBAL PART NUMBER INFORMATION (1) NEW GLOBAL PART NUMBER: Y000780K5000V9L (preferred part number format) DENOTES PRECISION VALUE CHARACTERISTICS Y R= K = k M = M 0 = standard 9 = lead (Pb)-free 1 to 999 = custom Y 0 0 0 7 8 0 K 5 0 0 0 V 9 PRODUCT CODE RESISTANCE TOLERANCE PACKAGING 0007 = S102C 0785 = S102J 0062 = S102K 0786 = S102L 0011 = S104D 5011 = S104F 0101 = S104K 4101 = S104L 0012 = S105D 4012 = S105F 0102 = S105K 4102 = S105L 0013 = S106D 0103 = S106K V = 0.005 % T = 0.01 % Q = 0.02 % A = 0.05 % B = 0.1 % C = 0.25 % D = 0.5 % F = 1.0 % L = bulk pack L FOR EXAMPLE: ABOVE GLOBAL ORDER Y0007 80K5000 V 9 L: TYPE: S102C VALUE: 80.5 k ABSOLUTE TOLERANCE: 0.005 % TERMINATION: lead (Pb)-free PACKAGING: bulk pack HISTORICAL PART NUMBER: S102C T 250R00 V B (will continue to be used) S102C T 250R00 V B MODEL TERMINATION S102C S102J S102K S102L S104D S104F S104K S104L S105D S105F S105K S105L S106D S106K T = lead (Pb)-free None = tin/lead alloy RESISTANCE VALUE TOLERANCE 250R00 = 250.00 5K2310 = 5.231 k 1M000 = 1 M V = 0.005 % T = 0.01 % Q = 0.02 % A = 0.05 % B = 0.1 % C = 0.25 % D = 0.5 % F = 1.0 % PACKAGING B = bulk pack Note (1) For non-standard requests, please contact application engineering. Document Number: 63001 Revision: 25-Jun-09 For any questions, contact: foil@vishay.com www.vishay.com 5 Legal Disclaimer Notice Vishay Disclaimer All product specifications and data are subject to change without notice. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, "Vishay"), disclaim any and all liability for any errors, inaccuracies or incompleteness contained herein or in any other disclosure relating to any product. Vishay disclaims any and all liability arising out of the use or application of any product described herein or of any information provided herein to the maximum extent permitted by law. The product specifications do not expand or otherwise modify Vishay's terms and conditions of purchase, including but not limited to the warranty expressed therein, which apply to these products. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. The products shown herein are not designed for use in medical, life-saving, or life-sustaining applications unless otherwise expressly indicated. Customers using or selling Vishay products not expressly indicated for use in such applications do so entirely at their own risk and agree to fully indemnify Vishay for any damages arising or resulting from such use or sale. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. Product names and markings noted herein may be trademarks of their respective owners. Document Number: 91000 Revision: 18-Jul-08 www.vishay.com 1