Y0062920R000D9L - Vishay Presicion Group

High Precision Foil Resistor with TCR of ± 2.0 ppm/°C,

Tolerance of ± 0.005 % and Load Life Stability of ± 0.005 %

Document Number: 63001 For any questions, contact: foil@vishay.com www.vishay.com

Revision: 25-Jun-09 1

S Series

Vishay Foil Resistors

INTRODUCTION

Bulk Metal® Foil (BMF) technology outperforms all other

resistor technologies available today for applications that

require high precision and high stability.

This technology has been pioneered and developed by

VISHAY, and products based on this technology are the

most suitable for a wide range of applications. BMF

technology allows us to produce customer orientated

products, designed to satisfy challenging and specific

technical requirements.

Model S series made from Vishay BMF offers low TCR,

excellent load life stability, tight tolerance, fast response

time, low current noise, low thermal EMF and low voltage

coefficient, all in one resistor.

The S series is virtually insensitive to destabillizing factors.

The resistor element is a solid alloy that displays the

desirable bulk properties of its parent material, thus it is

inherently stable and noise free.

Vishay’s Bulk Metal® S series resistors are the modern

generation of precision resistors. The standard design of

these resistors provides a unique combination of

characteristics found in no other single resistor.

Our application engineering department is available to

advise and to make recommendations. For non-standard

technical requirements and special applications, please

FEATURES

•

Temperature coefficient of resistance (TCR):

- 55 °C to + 125 °C, 25 °C ref.

- S102C series: ± 2 ppm/°C typical (see table 1)

- S102K series: ± 1 ppm/°C typical (see table 1)

•

Rated power: to 1 W at + 125 °C

•

Tolerance: ± 0.005 % (50 ppm)

•

Load life stability: to ± 0.005 % at 70 °C, 2000 h at rated

power

•

Resistance range: 0.5

to 1 M

(higher or lower values of

resistance are available)

•Vishay Foil resistors are not restricted to standard values;

specific “as required” values can be supplied at no extra

cost or delivery (e.g. 1K2345 vs. 1K)

•Electrostatic discharge up to 25 000 V

•

Non inductive, non capacitive design

•Rise time: 1 ns effectively no ringing

•

Current noise: 0.010 µV

RMS

/V of applied voltage (< - 40 dB)

•

Thermal EMF: 0.05 µV/°C typical

•

Voltage coefficient: < 0.1 ppm/V

•

Low inductance: < 0.08 µH typical

•

Non hot spot design

•Terminal finish: lead (Pb)-free or tin/lead alloy

•

Matched sets are available per request

(TCR tracking: to 0.5 ppm/°C)

•Prototype quantities available in just 5 working days

or sooner. For more information, please contact

foil@vishay.com

•For better TCR and PCR performances please review the

Z201 datasheet

APPLICATIONS

•High precision amplifiers

•Down-hole (high temperature)

•High precision instrumentation

•Medical and test equipment

•Industrial

•Audio (high end stereo equipment)

•EB applications (electron beam scanning and recording

equipment, electron microscopes)

•Military, airborne

•Measurement instrumentation

* Pb containing terminations are not RoHS compliant, exemptions may apply

TABLE 1 - RESISTANCE VERSUS TCR

(- 55 °C to + 125 °C, + 25 °C ref.)

RESISTOR RESISTANCE

VALUE (Ω)

TYPICAL TCR AND

MAX SPREAD

(ppm/°C)

S102(C) 80 to < 150K ± 2 ± 2.5

S102(K) 80 to < 100K ± 1 ± 2.5

S102(C) 50 to < 80 ± 2 ± 3.5

S102(K) ± 1 ± 3.5

S102(C) 1 to < 50 ± 2 ± 4.5

S102(K) ± 1 ± 4.5

FIGURE 1 - FOIL RESISTOR TCR COMPARISON OF

FOIL ALLOYS IN MILITARY RANGE

- 50 - 25 0 + 25 + 50 + 75 + 100 + 125

- 55

C Alloy

2 ppm/°C

K Alloy

1 ppm/°C

2 ppm/°C

+ 150

+ 100

+ 50

- 50

- 100

- 150

- 200

ΔR

(ppm)

Temperature (°C)

S Series

Vishay Foil Resistors

www.vishay.com For any questions, contact: foil@vishay.com Document Number: 63001

2Revision: 25-Jun-09

Notes

(1) S104F and S105F have different package dimensions (see last column). All other specifications are the same.

(2) 0.200" (5.08 mm) lead spacing available - specify S102J for S102C, and S102L for S102K.

FIGURE 2 - STANDARD IMPRINTING AND DIMENSIONS

Note

1. The standoffs shall be so located as to give a lead clearance of 0.010" minimum between the resistor body and the printed circuit board

when the standoffs are seated on the printed circuit board. This is to allow for proper cleaning of flux and other contaminants from the unit

after all soldering processes.

TABLE 2 - MODEL SELECTION

MODEL

NUMBER

RESISTANCE

RANGE

(Ω)

MAXIMUM

WORKING

VOLTAGE

AMBIENT

POWER RATING AVERAGE

WEIGHT

IN GRAMS

DIMENSIONS TIGHTEST

TOLERANCE

VS. LOWEST

RESISTANCE

VALUE

+ 70 °C

+ 125 °C INCHES mm F (1)

(INCHES)

S102C

(S102J) (2) 1 to 150K

300

0.6 W 0.3 W

0.6

W: 0.105 ± 0.010

L: 0.300 ± 0.010

H: 0.326 ± 0.010

ST: 0.010 min.

SW: 0.035 ± 0.010

LL: 1.000 ± 0.125

LS: 0.150 ± 0.0054

2.67 ± 0.25

7.62 ± 0.25

8.28 ± 0.25

0.254 min.

1.02 ± 0.13

25.4 ± 3.18

3.81 ± 0.13

0.005 %/50 Ω

0.01 %/25 Ω

0.02 %/12 Ω

0.05 %/5 Ω

0.1 %/2 Ω

0.50 %/1 Ω

up to 100K

S102K

(S102L) (2) 1 to 100K

0.4 W 0.2 W

over 100K

S104D

(S104F) (1) 1 to 500K

350

1.0 W 0.5 W

1.4

W: 0.160 max.

L: 0.575 max.

H: 0.413 max.

ST: 0.035 ± 0.005

SW: 0.050 ± 0.005

LL: 1.000 ± 0.125

LS: 0.400 ± 0.020

4.06 max.

14.61 max.

10.49 max.

0.889 ± 0.13

1.27 ± 0.13

25.4 ± 3.18

10.16 ± 0.51

(0.138)

(0.565)

(0.413)

up to 200K

S104K 1 to 300K

0.6 W 0.3 W

over 200K

S105D

(S105F) (1) 1 to 750K

350

1.5 W 0.75 W

1.9

W: 0.160 max.

L: 0.820 max.

H: 0.413 max.

ST: 0.035 ± 0.005

SW: 0.050 ± 0.005

LL: 1.000 ± 0.125

LS: 0.650 ± 0.020

4.06 max.

20.83 max.

10.49 max.

0.889 ± 0.13

1.27 ± 0.13

25.4 ± 3.18

16.51 ± 0.51

(0.138)

(0.890)

(0.413)

(0.7 ± 0.05)

up to 300K

S105K 1 to 500K

0.8 W 0.4 W

over 300K

S106D 0.5 to 1M

500

2.0 W 1.0 W

4.0

W: 0.260 max.

L: 1.200 max.

H: 0.413 max.

ST: 0.035 ± 0.005

SW: 0.050 ± 0.005

LL: 1.000 ± 0.125

LS: 0.900 ± 0.020

6.60 max.

30.48 max.

10.49 max.

0.889 ± 0.13

1.27 ± 0.13

25.4 ± 3.18

22.86 ± 0.51

up to 400K

S106K 0.5 to 600K

1.0 W 0.5 W

over 400K

Model Number

VISHAY

XXXX

S102C

ST1)

Date Code

Front View Rear View

Lead Material #22 AWG

Round Solder Coated Copper

Optional Customer Part Number

Print specification, etc. if required

Resistance

Value Code

Tolerance

XXXXXX

100R01

0.01 %

Week

Year

Document Number: 63001 For any questions, contact: foil@vishay.com www.vishay.com

Revision: 25-Jun-09 3

S Series

Vishay Foil Resistors

FIGURE 3 - POWER DERATING CURVE

100 %

75 %

50 %

25 %

- 75 - 50 - 25 0 + 25 + 50 + 75 + 100 + 125 + 150 + 175 + 200

Ambient Temperature (°C)

Percent of Rated Power at + 70 °C

- 55 °C + 70 °C

Rated Power

∆

Recommended

operation for

< 150 ppm ΔR

after 2000 h

load life

FIGURE 4 - TRIMMING TO VALUES

(conceptual illustration)

Mutual Inductance

Reduction due

to Change in

Current Direction

Current Path

Before Trimming

Note: Foil shown in black, etched spaces in white

Interloop Capacitance

Reduction in Series

Trimming Process

Removes this Material

from Shorting Strip Area

Changing Current Path

and Increasing

Resistance

Current Path

After Trimming

TABLE 3 - ENVIRONMENTAL PERFORMANCE COMPARISON

MIL-PRF-55182

CHAR J

S-SERIES

MAXIMUM ΔR

S-SERIES

TYPICAL ΔR

Test Group I

Thermal shock, 5 x (- 65 °C to + 150 °C) ± 0.2 % ± 0.01 % (100 ppm) ± 0.002 % (20 ppm)

Short time overload, 6.25 x rated power ± 0.2 % ± 0.01 % (100 ppm) ± 0.003 % (30 ppm)

Test Group II

Resistance temperature characteristics ± 25 ppm/°C ± 4.5 ppm/°C ± 2.0 ppm/°C

Characteristic

Low temperature storage (24 h at - 65 °C) ± 0.15 % ± 0.01 % (100 ppm) ± 0.002 % (20 ppm)

Low temperature operation

(45 min, rated power at - 65 °C) ± 0.15 % ± 0.01 % (100 ppm) ± 0.002 % (20 ppm)

Terminal strength ± 0.2 % ± 0.01 % (100 ppm) ± 0.002 % (20 ppm)

Test Group III

DWV ± 0.15 % ± 0.01 % (100 ppm) ± 0.002 % (20 ppm)

Resistance to solder heat ± 0.1 % ± 0.01 % (100 ppm) ± 0.005 % (50 ppm)

Moisture resistance ± 0.4 % ± 0.05 % (500 ppm) ± 0.01 % (100 ppm)

Test Group IV

Shock ± 0.2 % ± 0.01 % (100 ppm) ± 0.002 % (20 ppm)

Vibration ± 0.2 % ± 0.01 % (100 ppm) ± 0.002 % (20 ppm)

Test Group V

Life test at 0.3 W/+ 125 °C

2000 h ± 0.5 % ± 0.015 % (150 ppm) ± 0.01 % (100 ppm)

10 000 h ± 2.0 % ± 0.05 % (500 ppm) ± 0.03 % (300 ppm)

Test Group Va

Life test at 0.6 W (2 x rated power)/+ 70 °C, 2000 h ± 0.5 % ± 0.015 % (150 ppm) ± 0.01 % (100 ppm)

Test Group VI

High temperature exposure (2000 h at + 175 °C) ± 2.0 % ± 0.1 % (1000 ppm) ± 0.05 % (500 ppm)

Test Group VII

Voltage coefficient 5 ppm/V < 0.1 ppm/V < 0.1 ppm/V

S Series

Vishay Foil Resistors

www.vishay.com For any questions, contact: foil@vishay.com Document Number: 63001

4Revision: 25-Jun-09

STANDARD OPERATIONS AND TEST

CONDITIONS

A. Standard Test Operations:

By 100 % Inspection

•Short-time overload (6.25 x rated power for 5 s)

•Resistance - tolerance check

•Visual and mechanical

By Sample Inspection

•TCR

•Environmental tests per table 3 on a quarterly basis to

establish performance by similarity

B. Standard Test Conditions:

•Lead test point: 0.5" (12.7 mm) from resistor body

•Temperature: + 23 °C ± 2 °C

•Relative humidity: per MIL-STD-202

IMPROVED PERFORMANCE TESTING (IPT)

The preceding information is based on product directly off

the production line. Improved performance (meaning

increased time stability with load and other stresses) is

available through factory conducted “Improved Performance

Testing”. The test routine is usually tailored to the users

stability objectives and product that has been screened can

be brought down to a potential load life of less than 50 ppm.

Various screen test routines are available and all anticipated

stresses must be taken into account before settling on one

specific test routine. Our applications engineering

department is prepared to discuss and recommend

appropriate routines given the full spectrum of anticipated

stresses and stability requirements.

Notes

(1) Load life ΔR maximum can be reduced by 80 %, please contact applications engineering department.

(2) Inductance (L) due mainly to the leads.

(3) The resolution limit of existing test equipment (within the measurement capability of the equipment, or “essentially zero”.)

(4) µV/°C relates to EMF due to lead temperature difference and µV/watt due to power applied to the resistor.

TABLE 4 - “S” SERIES SPECIFICATIONS

Stability (1)

Load life at 2000 h ± 0.015 % (150 ppm) Maximum ΔR at 0.3 W/+ 125 °C

± 0.005 % (50 ppm) Maximum ΔR at 0.1 W/+ 70 °C

Load life at 10 000 h ± 0.05 % (500 ppm) Maximum ΔR at 0.3 W/+ 125 °C

± 0.01 % (100 ppm) Maximum ΔR at 0.05 W/+ 125 °C

Current Noise 0.010 µV (RMS)/V of applied voltage (- 40 dB)

High Frequency Operation

Rise time 1.0 ns at 1 kΩ

Inductance (L) (2) 0.1 µH maximum; 0.08 µH typical

Capacitance (C) 1.0 pF maximum; 0.5 pF typical

Voltage Coefficient < 0.1 ppm/V (3)

Thermal EMF (4) 0.1 µV/°C Maximum; 0.05 µV/°C typical

1 µV/W (Model S102C)

Document Number: 63001 For any questions, contact: foil@vishay.com www.vishay.com

Revision: 25-Jun-09 5

S Series

Vishay Foil Resistors

Note

(1) For non-standard requests, please contact application engineering.

TABLE 5 - GLOBAL PART NUMBER INFORMATION (1)

NEW GLOBAL PART NUMBER: Y000780K5000V9L (preferred part number format)

DENOTES PRECISION VALUE CHARACTERISTICS

YR = Ω

K = kΩ

M = MΩ

0 = standard

9 = lead (Pb)-free

1 to 999 = custom

PRODUCT CODE RESISTANCE TOLERANCE PACKAGING

0007 = S102C

0785 = S102J

0062 = S102K

0786 = S102L

0011 = S104D

5011 = S104F

0101 = S104K

4101 = S104L

0012 = S105D

4012 = S105F

0102 = S105K

4102 = S105L

0013 = S106D

0103 = S106K

V = ± 0.005 %

T = ± 0.01 %

Q = ± 0.02 %

A = ± 0.05 %

B = ± 0.1 %

C = ± 0.25 %

D = ± 0.5 %

F = ± 1.0 %

L = bulk pack

FOR EXAMPLE: ABOVE GLOBAL ORDER Y0007 80K5000 V 9 L:

TYPE: S102C

VALUE: 80.5 kΩ

ABSOLUTE TOLERANCE: ± 0.005 %

TERMINATION: lead (Pb)-free

PACKAGING: bulk pack

HISTORICAL PART NUMBER: S102C T 250R00 V B (will continue to be used)

S102C T 250R00 V B

MODEL TERMINATION RESISTANCE VALUE TOLERANCE PACKAGING

S102C

S102J

S102K

S102L

S104D

S104F

S104K

S104L

S105D

S105F

S105K

S105L

S106D

S106K

T = lead (Pb)-free

None = tin/lead alloy

250R00 = 250.00 Ω

5K2310 = 5.231 kΩ

1M000 = 1 MΩ

V = ± 0.005 %

T = ± 0.01 %

Q = ± 0.02 %

A = ± 0.05 %

B = ± 0.1 %

C = ± 0.25 %

D = ± 0.5 %

F = ± 1.0 %

B = bulk pack

0078 K500Y0 V90 L0

Document Number: 91000 www.vishay.com

Revision: 18-Jul-08 1

Disclaimer

Legal Disclaimer Notice

Vishay

All product specifications and data are subject to change without notice.

Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf

(collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained herein

or in any other disclosure relating to any product.

Vishay disclaims any and all liability arising out of the use or application of any product described herein or of any

information provided herein to the maximum extent permitted by law. The product specifications do not expand or

otherwise modify Vishay’s terms and conditions of purchase, including but not limited to the warranty expressed

therein, which apply to these products.

No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this

document or by any conduct of Vishay.

The products shown herein are not designed for use in medical, life-saving, or life-sustaining applications unless

otherwise expressly indicated. Customers using or selling Vishay products not expressly indicated for use in such

applications do so entirely at their own risk and agree to fully indemnify Vishay for any damages arising or resulting

from such use or sale. Please contact authorized Vishay personnel to obtain written terms and conditions regarding

products designed for such applications.

Product names and markings noted herein may be trademarks of their respective owners.