FUJITSU SEMICONDUCTOR DATA SHEET DS07-12546-1E 8-bit Original Microcontroller CMOS F2MC-8L MB89530H Series MB89537H/537HC/538H/538HC/ MB89P538/PV530 DESCRIPTION The MB89530H series is a one-chip microcontroller featuring the F2MC-8L core supporting low-voltage and highspeed operation. Built-in peripheral functions include timers, serial interface, A/D converter, and external interrupt. This product is an ideal general-purpose one-chip microcontroller for a wide variety of applications from household to industrial equipment, as well as use in portable devices. FEATURES * Wide range of package options * Two types of QFP packages (1 mm pitch, 0.65 mm pitch) * LQFP package (0.5 mm pitch) * SH-DIP package * Low voltage, high-speed operating capability * Minimum instruction execution time 0.32 s (at base oscillator 12.5 MHz) * F2MC-8L CPU Core * Instruction set optimized for controller operation * Multiplication/division instructions * 16-bit calculation * Branching instructions with bit testing * Bit operation instructions, etc. * Five timer systems * 8-bit PWM timer with 2 channels (usable as either interval timer of PWM timer) * Pulse width count timer (supports continuous measurement or remote control receiving applications) * 16-bit timer counter * 21-bit time base timer * Clock prescaler (17-bit) * UART * Synchronous or asynchronous operation, switchable * 2 serial interfaces (Serial I/O) * Selection of transfer direction (specify MSB first or LSB first) for communication with a variety of devices (Continued) MB89530H Series (Continued) * 10-bit A/D converter (8 channels) * External clock input and time base timer output for startup support * Pulse generators (PPG) with 2-program capability * 6-bit PPG with selection of pulse width and pulse period * 12-bit PPG (2 channels) with selection of pulse width and pulse period * I2C interface circuits * External interrupt 1 (4 channels) * 4 independent inputs, release enabled from standby mode (includes edge detection function) * External interrupt 2 (8 channels) * 8 independent inputs, release enabled form standby mode (includes level edge detection function) * Standby modes (low power consumption modes) * Stop mode (oscillator stops, virtually no power consumed) * Sleep mode (CPU stops, power consumption reduced to one-third) * Sub clock mode * Clock mode * Watchdog timer reset * I/O ports * Maximum 53 ports * 38 general-purpose I/O ports (CMOS) * 2 general-purpose I/O ports (N-ch open drain) * 8 general-purpose output ports (N-ch open drain) * 5 general-purpose input ports (CMOS) PACKAGES 2 64-pin, Plastic SH-DIP 64-pin, Plastic LQFP 64-pin, Plastic QFP (DIP-64P-M01) (FPT-64P-M03) (FPT-64P-M06) 64-pin, Plastic QFP 64-pin, Ceramic MDIP 64-pin, Ceramic MQFP (FPT-64P-M09) (MDP-64C-P02) (MQP-64C-P01) MB89530H Series PRODUCT LINEUP Part number MB89537H/537HC Parameter Type MB89538H/538HC Mass produced (Mask ROM) ROM capacity 32 K x 8-bit (built-in ROM) RAM capacity 1 K x 8-bit 48 K x 8-bit (built-in ROM) MB89P538 MB89PV530 One-time programmable Evaluation 48 K x 8-bit (built-in ROM) (write from general purpose ERPOM writer) 48 K x 8-bit (external ROM) *2 2 K x 8-bit 1 Operating voltage Peripheral functions CPU functions 3.5 V to 5.5 V* (MB89537H/538H/537HC/538HC) Basic instructions Instruction bit length Instruction length Data bit length Minimum instruction execution time Minimum interrupt processing time 2.7 V to 5.5 V : 136 : 8-bits : 1 bit to 3 bits : 1, 8, 16-bits : 0.32 s / 12.5 MHz : 2.88 s / 12.5 MHz Ports Input ports : 5 (4 also usable as interrupts, 2 for sub clock) Output-only ports (N-ch open drain) : 8 (8 also usable as ADC input) I/O ports (N-ch open drain) : 2 (2 also usable as SO2/SDA or SI2/SCL) I/O ports (CMOS) : 38 (21 have no other function) Total : 53 Time base timer 21 bits Interrupt periods at main clock oscillation frequency of 12.5 MHz (approx. 0.655 ms, 2.621 ms, 20.97 ms, 335.5 ms) Watchdog timer Reset period of approx. 167.8 ms to 335.6 ms at mail clock frequency of 12.5 MHz Reset period of approx. 500 ms to 1000 ms at sub clock frequency of 32.768 kHz. PWM timer 8-bit interval timer operation*3 (supports square wave output, operating clock period : 1, 8, 16, 64 tinst*3) Pulse width measurement with 8-bit resolution (conversion period : 28 tinst*3 to 28 x 64 tinst*3) 2 channels (can also be used as interval timer, can also be used as ch1 output and ch2 count clock) Clock prescaler Interval times at 17-bit sub clock base frequency of 32.768 kHz (approx. 31.25 ms, 0.25 s, 0.50 s, 1.00 s, 2.00 s, 4.00 s) (Continued) 3 MB89530H Series Peripheral functions (Continued) Part number Parameter MB89537H/537HC MB89538H/538HC MB89P538 MB89PV530 Pulse width count timer 8-bit one-shot timer operation (supports underflow output, operating clock period : 1, 4, 32 tinst*3, external) 8-bit reload timer operation (supports square wave output, operating clock period : 1, 4, 32 tinst*3, external) 8-bit pulse width measurement operation (continuous measurement, H width measurement, L width measurement, to , to , H width measurement and to) 16-bit timer/ counter 16-bit timer operation (operating clock period : 1 tinst*3, external) 16-bit event counter operation (select rising, falling, or both edges) 16-bit x 1 ch Serial I/O 8 bit length Selection of LSB first or MSB first Transfer clock (2, 8, 32 tinst*3, external) UART/SIO CLK synchronous/CLK asynchronous data transfer capability (8, 9 bit with parity bit, or 7,8 bit without parity bit) . Built-in baud rate generator provides selection of 14 baud rate settings. UART CLK synchronous/CLK asynchronous data transfer capability (4, 6, 7, 8 bit with parity bit, or 5, 7, 8, 9 bit without parity bit) . Built-in baud rate generator provides selection of 14 baud rate settings. External clock input, 2-channel 8-bit PWM timer output also available for baud rate settings. 4-channel independent. External interrupt 1 Selection of rising, falling, or both edge detection. Can be used for recovery from standby mode (edge detection also available in stop mode) External interrupt 2 8-channel independent L level detection. Can be used for recovery from standby mode. 6-bit PPG, 12-bit PPG Can generate square wave signals with programmable period. 6-bit x 1 channel or 12-bit x 2 channels. I C bus interface 1-channel , compatible with Intel System Administrator bus version 1.0 and Philips I2C specifications. 2-line communications (on MB89PV530/P538/537HC/538HC) A/D converter 10-bit resolution x 8 channels. A/D conversion functions (conversion time : 60 tinst*3) Supports repeated calls from external clock or internal clock. Standard voltage input provided (AVR) 2 Standby modes Sleep mode, stop mode, sub clock mode, clock mode. (power saving modes) Process CMOS *1 : Depends on operating frequency. *2 : Using external ROM and MBM27C512. *3 : tinst represents instruction execution time. This can be selected as 1/4, 1/8, 1/16, 1/64 of the main clock cycle or 1/2 of the sub clock cycle. Note : MB89537H/538H have no built-in I2C functions. To use I2C functions, choose the MB89PV530/MB89P538/537HC/538HC. 4 MB89530H Series MODEL DIFFERENCES AND SELECTION CONSIDERATIONS Part number Package MB89537H/537HC MB89538H/538HC MB89P538 MB89PV530 DIP-64P-M01 O O O X FPT-64P-M03 O O X X FPT-64P-M06 O O O X FPT-64P-M09 O O O X MDP-64C-P02 X X X O MQP-64C-P01 X X X O O : Model-package combination available X : Model-package combination not available Conversion sockets for pin pitch conversion (manufactured by Sunhayato) can be used. Contact : Sunhayato TEL +81-3-3984-7791 (Tokyo) DIFFERENCES AMONG PRODUCTS 1. Memory Capacity When this product is used in a piggy-back or other evaluation configuration, it is necessary to carefully confirm the differences between the model being used and the product it is evaluating. Particular attention should be given to the following (see " CPU CORE 1.Memory Space") . * The program ROM area starts from address 4000H on the MB89P538 and MB89PV530 models. * Note upper limits on RAM, such as stack areas, etc. 2. Current Consumption * On the MB89PV530, the additional current consumed by the EPROM is added at the connecting socket on the back side. * When operating at low speed, the current consumption in the one-time PROM or EPROM models is greater than on the mask ROM models. However, current consumption in sleep or stop modes is identical. For details, refer to " ELECTRICAL CHARACTERISTICS". 3. Mask Options The options available for use, and the method of specifying options, differ according to the model. Before use, check the " MASK OPTIONS" specification section. 4. Wild Register Functions The following table shows areas in which wild register functions can be used. Wild Register Usage Areas Part number Address space MB89PV530 4000H to FFFFH MB89P538 4000H to FFFFH MB89537H/537HC 8000H to FFFFH MB89538H/538HC 4000H to FFFFH 5 MB89530H Series PIN ASSIGNMENTS (TOP VIEW) P36/WTO P37/PTO1 P40/INT20/EC P41/INT21/SCK2 P42/INT22/SO2/SDA P43/INT23/SI2/SCL P44/INT24/UCK2 P45/INT25/UO2 P46/INT26/UI2 P47/INT27/ADST P50/AN0 P51/AN1 P52/AN2 P53/AN3 P54/AN4 P55/AN5 P56/AN6 P57/AN7 AVCC AVR AVSS P60/INT10 P61/INT11 P62/INT12 P63/INT13/X0A P64/X1A RST MOD0 MOD1 X0 X1 VSS 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 *1 A15 A12 A7 A6 A5 A4 A3 A2 A1 A0 O1 O2 O3 VSS 65 66 67 68 69 70 71 72 73 74 75 76 77 78 92 91 90 89 88 87 86 85 84 83 82 81 80 79 VCC A14 A13 A8 A9 A11 OE A10 CE O8 O7 O6 O5 O4 64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 VCC P35/PWC P34/PTO2 P33/SI1 (UI1) P32/SO1 (UO1) P31/SCK1 (UCK1) /LMCO P30/PPG03/MCO C/NC *2 P00 P01 P02 P03 P04 P05 P06 P07 P10 P11 P12 P13 P14 P15 P16 P17 P20/PWCK P21/PPG01 P22/PPG02 P23 P24 P25 P26 P27 (DIP-64P-M01) (MDP-64C-P02) *1 : Package top pin assignments (MB89PV530 only) Pin no. Pin name Pin no. Pin name Pin no. Pin name Pin no. Pin name 65 A15 73 A1 81 O6 89 A8 66 A12 74 A0 82 O7 90 A13 67 A7 75 O1 83 O8 91 A14 68 A6 76 O2 84 CE 92 VCC 69 A5 77 O3 85 A10 70 A4 78 VSS 86 OE 71 A3 79 O4 87 A11 72 A2 80 O5 88 N.C. : Internal connection only. Not for use. *2 : The function of pin 57 depends on the model. For details, see " A9 HANDLING DEVICES". (Continued) 6 MB89530H Series 64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49 P45/INT25/UO2 P44/INT24/UCK2 P43/INT23/SI2/SCL P42/INT22/SO2/SDA P41/INT21/SCK2 P40/INT20/EC P37/PTO1 P36/WTO VCC P35/PWC P34/PTO2 P33/SI1 (UI1) P32/SO1 (UO1) P31/SCK1 (UCK1) /LMCO P30/PPG03/MCO C/NC (TOP VIEW) 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 P00 P01 P02 P03 P04 P05 P06 P07 P10 P11 P12 P13 P14 P15 P16 P17 P63/INT13/X0A P64/X1A RST MOD0 MOD1 X0 X1 VSS P27 P26 P25 P24 P23 P22/PPG02 P21/PPG01 P20/PWCK 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 P46/INT26/UI2 P47/INT27/ADST P50/AN0 P51/AN1 P52/AN2 P53/AN3 P54/AN4 P55/AN5 P56/AN6 P57/AN7 AVCC AVR AVSS P60/INT10 P61/INT11 P62/INT12 (FPT-64P-M03) (FPT-64P-M09) * : The function of pin 49 depends on the model. For details, see " HANDLING DEVICES". (Continued) 7 MB89530H Series (Continued) 64 63 62 61 60 59 58 57 56 55 54 53 52 P44/INT24/UCK2 P43/INT23/SI2/SCL P42/INT22/SO2/SDA P41/INT21/SCK2 P40/INT20/EC P37/PTO1 P36/WTO VCC P35/PWC P34/PTO2 P33/SI1 (UI1) P32/SO1/ (UO1) P31/SCK1 (UCK1) /LMCO (TOP VIEW) 84 83 82 81 80 79 78 1 85 86 87 88 89 90 91 92 93 77 76 75 74 73 72 71 70 69 94 95 96 65 66 67 68 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 51 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 P30/PPG03/MCO C/NC 2 P00 P01 P02 P03 P04 P05 P06 P07 P10 P11 P12 P13 P14 P15 P16 P17 P20/PWCK RST MOD0 MOD1 X0 X1 VSS P27 P26 P25 P24 P23 P22/PPG02 P21/PPG01 20 21 22 23 24 25 26 27 28 29 30 31 32 P45/INT25/UO2 P46/INT26/UI2 P47/INT27/ADST P50/AN0 P51/AN1 P52/AN2 P53/AN3 P54/AN4 P55/AN5 P56/AN6 P57/AN7 AVCC AVR AVSS P60/INT10 P61/INT11 P62/INT12 P63/INT13/X0A P64/X1A (FPT-64P-M06) (MQP-64C-P01) *1 : Package top pin assignments (MB89PV530 only) Pin no. Pin name Pin no. Pin name Pin no. Pin name Pin no. Pin name 65 N.C. 73 A2 81 N.C. 89 OE 66 A15 74 A1 82 O4 90 N.C. 67 A12 75 A0 83 O5 91 A11 68 A7 76 N.C. 84 O6 92 A9 69 A6 77 O1 85 O7 93 A8 70 A5 78 O2 86 O8 94 A13 71 A4 79 O3 87 CE 95 A14 72 A3 80 VSS 88 A10 96 VCC N.C. : Internal connection only. Not for use. *2 : The function of pin 50 depends on the model. For details, see " 8 HANDLING DEVICES". MB89530H Series PIN DESCRIPTIONS Pin no. SH-DIP*1 MDIP*2 QFP*3 MQFP*4 LQFP*5 QFP*6 Pin name 30 23 22 X0 31 24 23 X1 28 21 20 MOD0 29 22 21 MOD1 I/O circuit type Function A Connecting pins to crystal oscillator circuit or other oscillator circuit. The X0 pin can connect to an external clock. In that case, X1 is left open. B Input pins for memory access mode setting. Connect directly to Vss. 27 20 19 RST C Reset I/O pin. This pin has pull-up resistance with CMOS I/O or hysteresis input. At an internal reset request, an 'L' signal is output. An 'L' level input initializes the internal circuits. 56 to 49 49 to 42 48 to 41 P00 to P07 D General purpose I/O ports. 48 to 41 41 to 34 40 to 33 P10 to P17 D General purpose I/O ports. 40 33 32 P20/PWCK E General purpose I/O port.Resource I/O pin (hysteresis input).Hysteresis input. This pin also functions as a PWC input. 39 32 31 P21/ PPG01 D General purpose I/O port.This pin also functions as the PPG01 output. 38 31 30 P22/ PPG02 D General purpose I/O port.This pin also functions as the PPG02 output. 37 30 29 P23 D General purpose I/O port. 36 29 28 P24 D General purpose I/O port. 35 28 27 P25 D General purpose I/O port. 34 27 26 P26 D General purpose I/O port. 33 26 25 P27 D General purpose I/O port. 58 51 50 P30/ PPG03/ MCO D General purpose I/O port.This pin also functions as the PPG03 output. 59 52 51 P31/SCK1 (UCK1) / LMCO E General purpose I/O port.Resource I/O pin (hysteresis input).This pin also functions as the UART/SIO clock input/output pin. 60 53 52 P32/SO1 (UO1) D General purpose I/O port.This pin also functions as the UART/SIO serial data output pin. 61 54 53 P33/SI1 (UI1) E General purpose I/O port.Resource input/output pin (hysteresis input).This pin also functions as the UART/ SIO serial data input pin. 62 55 54 P34/PTO2 D General purpose I/O port.This pin also functions as the PWM time 2 output pin. 63 56 55 P35/PWC E General purpose I/O port.Resource I/O pin (hysteresis input).This pin also functions as a PWC input. (Continued) 9 MB89530H Series Pin no. QFP*3 MQFP*4 LQFP*5 QFP*6 Pin name I/O circuit type 1 58 57 P36/WTO D General purpose I/O port.Resource output. This pin also functions as the PWC output pin. 2 59 58 P37/PTO1 D General purpose I/O port.Resource output. This pin also functions as the PWM timer 1 output pin. 3 60 59 P40/INT20/ EC E General purpose I/O port.Resource I/O pin (hysteresis input)This pin also functions as an external interrupt input or 16-bit timer/counter input. 4 61 60 P41/INT21/ SCK2 E General purpose I/O port.Resource I/O pin (hysteresis input)This pin also functions as an external interrupt input or SIO clock I/O pin. 61 P42/INT22/ SO2/SDA G N-ch open drain output. Resource I/O pin (hysteresis only for INT22 input) . This pin also functions as an external interrupt input, SIO serial data output, or I2C data line. 62 P43/INT23/ SI2/SCL G N-ch open drain output. Resource I/O pin (hysteresis only for INT23 input) . This pin also functions as an external interrupt, SIO serial data input, or I2C clock I/O pin. 63 P44/INT24/ UCK2 E General purpose I/O port. Resource I/O pin (hysteresis input) . This pin also functions as an external interrupt input or UART clock I/O pin. 64 P45/INT25/ UO2 E General purpose I/O port. Resource I/O pin (hysteresis input) . This pin also functions as an external interrupt input or UART data output pin. 1 P46/INT26/ UI2 E General purpose I/O port. Resource I/O pin (hysteresis input) . This pin also functions as an external interrupt input or UART data input pin. E General purpose I/O port. Resource I/O pin (hysteresis input) . This pin also functions as an external interrupt input or A/D converter clock input pin. SH-DIP* MDIP*2 1 5 6 7 8 9 62 63 64 1 2 Function 10 3 2 P47/INT27/ ADST 11 to 18 4 to 11 3 to 10 P50/AN0 to P57/AN7 H N-ch open drain output port. This pin also functions as an A/D converter analog input pin. 22 to 24 15 to 17 14 to 16 P60/INT10 to P62/INT12 I General purpose input port. Resource input pin (hysteresis input) . This pin also functions as an external interrupt input pin. (Continued) 10 MB89530H Series (Continued) Pin no. SH-DIP* MDIP*2 1 QFP*3 MQFP*4 LQFP*5 QFP*6 Pin name I/O circuit type Function I/A General purpose input port. Resource input (hysteresis input) . This pin also functions as an external interrupt or sub clock pin. 25 18 17 P63/INT13/ X0A 26 19 18 P64/X1A J/A General purpose input port. This pin also functions as a sub clock pin. 64 57 56 VCC Power supply pin. 32 25 24 VSS Ground pin (GND) . 19 12 11 AVCC A/D converter power supply pin. 20 13 12 AVR A/D converter reference voltage input pin. 21 14 13 AVSS A/D converter power supply pin. Used at the same voltage level as the Vss supply. 57 50 49 C MB89537H/537HC MB89538H/538HC Capacitor connection pin for stabilizing power supply connect an external ceramic capacitor of approximately 0.1F. MB89P538 If you select Yes for voltage step-down circuit stabilization time, this pin is fixed to VCC. If you select No for voltage step-down circuit stabilization time, this pin is fixed to VSS. MB89PV530 N.C. pin *1 : DIP-64P-M01 *2 : MDP-64C-P02 *3 : FPT-64P-M06 *4 : MQP-64C-P01 *5 : FPT-64P-M03 *6 : FPT-64P-M09 11 MB89530H Series External EPROM Socket Pin Function Descriptions (MB89PV530 only) Pin no. I/O Circuit Pin name type 1 2 MQFP* MDIP* 65 66 67 68 69 70 71 72 73 74 66 67 68 69 70 71 72 73 74 75 A15 A12 A7 A6 A5 A4 A3 A2 A1 A0 O Address output pins. 75 76 77 77 78 79 O1 O2 O3 I Data input pins 78 80 VSS O Power supply pin (GND) . 79 80 81 82 83 82 83 84 85 86 O4 O5 O6 O7 O8 I Data input pins. 84 87 CE O ROM chip enable pin. Outputs an "H" level signal in standby mode. 85 88 A10 O Address output pin. 86 89 OE O ROM output enable pin. Outputs "L" at all times. 87 88 89 91 92 93 A11 A9 A8 O 90 94 A13 O 91 95 A14 O 92 96 VCC O EPROM power supply pin. 65 76 81 90 N.C. O Internally connected. These pins always left open. *1 : MDP-64C-P02 *2 : MQP-64C-P01 12 Function Address output pins. MB89530H Series I/O CIRCUIT TYPES Type Circuit Remarks Oscillator feedback resistance * High speed side = approx. 1 M * Low speed side = approx. 10 M X1 (X1A) Nch A Pch Pch X0 (X0A) Nch * Hysteresis input * Pull-down resistance built-in to MB89535A MB89537H/537HC MB89538H/538HC B * Pull-up resistance approx. 50 k * Hysteresis input R Pch C Nch R Pull-up control resistor Pch * CMOS I/O * Software pull-up resistance can be used. Approx. 50 k Pch D Nch R Pull-up control resistors Pch * CMOS I/O * Software pull-up resistance can be used. Approx. 50 k Pch E Nch Port input Resource input (Continued) 13 MB89530H Series (Continued) Type Circuit Remarks * N-ch open drain output * Hysteresis input * CMOS input Nch G Resource input Port input * N-ch open drain output * Analog input (A/D converter) Pch H Nch Analog input R Pch Pull-up control resistors I * Hysteresis input * CMOS input * Software pull-up resistance can be used. Approx. 50 k Resource Port R Pch Pull-up control resistors J Port 14 * CMOS input * Software pull-up resistance can be used. Approx. 50 k MB89530H Series HANDLING DEVICES 1.Preventing Latchup Care must be taken to ensure that maximum voltage ratings are not exceeded (to prevent latchup) . When CMOS integrated circuit devices are subjected to applied voltages higher than Vcc at input and output pins (other than medium- and high-withstand voltage pins), or to voltages lower than Vss, as well as when voltages in excess of rated levels are applied between Vcc and Vss, the phenomenon known as latchup can occur. When a latchup condition occurs, supply current can increase dramatically and may destroy semiconductor elements. In using semiconductor devices, always take sufficient care to avoid exceeding maximum ratings. Also when switching power on or off to analog systems, care must be taken that analog power supplies (AVCC, AVR) and analog input signals do not exceed the level of the digital power supply. 2.Power Supply Voltage Fluctuations Keep supply voltage levels as stable as possible. Even within the warranted operating range of the Vcc supply voltage, sudden changes in supply voltage can cause abnormal operation. As a measure for stability, it is recommended that the Vcc ripple fluctuation (peak to peak value) should be kept within 10% of the reference Vcc value on commercial power supply (50 Hz-60 Hz), and instantaneous voltage fluctuations such as at power-on and shutdown should be kept within a transient variability limit of 0.1V/ms. 3.Treatment of Unused Input Pins If unused input pins are left open, abnormal operation may result. Any unused input pins should be connected to pull-up or pull-down resistance. 4. Treatment of N.C. Pins Any pins marked 'NC' (not connected) must be left open. 5. Treatment of Power Supply Pins on Models with Built-in A/D Converter Even when A/D converters are not in use, pins should be connected so that AVCC = VCC and AVSS = AVR = VSS. 6. Precautions for Use of External Clock Even when an external clock signal is used, an oscillator stabilization wait period is used after a power-on reset, or escape from sub clock mode or stop mode. 7. Execution of Programs on RAM Debugging of programs executed on RAM cannot be performed even when using the MB89PV530. 8.Wild Register Functions Wild registers cannot be debugged with the MB89PV530 and tools. To verify operations, actual in-device testing on the MB89P538 is advised. 15 MB89530H Series 9. Details of the C pin handling for MB89530H series MB89530H series contains the following products and the operating characteristics vary with whether they contain the internal stepdown circuit. Pin handling for the products depending on the internal voltage step-down circuit Part number Operating voltage Voltage step-down circuit Pin type Not included MB89PV530 2.7 V to 5.5 V MB89P538 2.7 V to 5.5 V MB89537H/537HC 3.5 V to 5.5 V Included C pin 0.1 F capacitor connected MB89538H/538HC 3.5 V to 5.5 V Included C pin 0.1 F capacitor connected Included Not included N.C. pin Pin handling C pin Not required Fixed to VCC Fixed to VSS The same built-in resources are used for the above product types; operating sequences after the power-on reset are different depending on whether they have the internal voltage step-down circuit. The operating sequences after the power-on reset with the different models will be described below. Operating sequences after the power-on reset with the different models Power supply (VCC) Voltage step-down circuit stabilization time + oscillation stabilization time (219/FCH) CPU operation of the product having the internal voltage stepdown circuit (MB89537H/ 537HC, MB89538H/538HC, MB89P538*) Oscillation stabilization time (218/FCH) CPU operation of the product not having the internal voltage step-down circuit (MB89PV530, MB89P538*) Start of CPU operation for the Start of CPU operation for the product not having the internal voltage product having the internal voltage step-down circuit (reset vector) step-down circuit (reset vector) FCH: Crystal oscillator frequency *: With the MB89P538, you can select the voltage step-down circuit to be included or not by introducing the C pin handling. Note: As described above, CPU starts at delayed time with the product having the internal voltage stepdown circuit compared with the product not having the internal voltage step-down circuit. This is because the time should be allowed for the stabilization time for voltage step-down circuit for normal operation. 16 MB89530H Series ONE-TIME WRITING SPECIFICATIONS WITH PROM AND EPROM MICROCONTROLLERS The MB89P538 has a PROM mode with functions equivalent to the MBM27C1001, allowing writing with a general purpose ROM writer using a proprietary adapter. Note, however, that the use of electronic signature mode is not supported. * ROM writer adapters With some ROM writers, stability of writing performance is enhanced by placing an 0.1F capacitor between the Vcc and Vss pins. The following table lists adapters for use with ROM writers. ROM Writer Adapters Part number Package Compatible adapter MB89P538-101PF MB89P538-201PF FPT-64P-M06 ROM-64QF-32DP-8LA2* MB89P538-101PFM MB89P538-201PFM FPT-64P-M09 ROM-64QF2-32DP-8LA MB89P538-101P-SH MB89P538-201P-SH DIP-64P-M01 ROM-64SD-32DP-8LA2* Inquiries should be addressed to Sunhayato, Ltd., : TEL +81-3-3984-7791 * : Version 3 or later should be used. * Memory map for EPROM mode The following illustration shows a memory map for EPROM mode. There are no PROM options. Normal operating mode 0000H EPROM mode (corresponding addresses on EPROM writer) 0000H I/O 0080H RAM 0100H 0200H 0880H General purpose register Prohibited Prohibited 4000H 4000H Program (EPROM) ROM FFFFH FFFFH Prohibited 1FFFFH 17 MB89530H Series * Recommended screening conditions Before one-time writing of microcontroller programs to PROM, high temperature aging is recommended as a screening process for chips before they are mounted. Program, verify High temperature aging +150 C, 48 h Read Mount * About writing yields The nature of chips before one-time writing of microcontroller programs to PROM prevents the use of all-bit writing tests. Therefore it is not possible to guarantee writing yields of 100% in some cases. 18 MB89530H Series EPROM WRITING TO PIGGY-BACK/EVALUATION CHIPS This section describes methods of writing to EPROM on piggy-back/evaluation chips. * EPROM model MBM27C512-20TV * Writer adapter For writing to EPROM using a ROM writer, use one of the writer adapters shown below (manufactured by Sunhayato) . Package Adapter socket model LCC-32 (rectangular) ROM-32LC-28DP-YG Inquiries should be addressed to Sunhayato, Ltd., : TEL +81-3-3984-7791 * Memory Space Normal operating mode 0000H (Corresponding address on ROM writer) 0000H I/O 0080H Prohibited RAM 0880H Prohibited 4000H 4000H PROM 48 KB FFFFH EPROM FFFFH * Writing to EPROM 1) Set up the EPROM writer for the MBM27C512. 2) Load program data to the ERPOM writer, in the area 4000H - FFFFH. 3) Use the EPROM writer to write to the area 4000H - FFFFH. 19 MB89530H Series CMOS I/O P64/X1A P60/INT10 P62/INT12 Low voltage oscillator circuit (32.786 kHz) CMOS I/O port Port 6 CMOS I/O port P31/SCK1 (UCK1) /LMCO 8-bit PWM timer 2 8-bit PWM timer 1 P34/PTO2 UART/SIO P35/PWC Port 2 P21/PPG01 P22/PPG02 P23 P27 CMOS I/O port P40/INT20/EC SIO P41/INT21/SCK2 UART P42/INT22/ SO2/SDA N-ch I/O I2C P43/INT23/ SI2/SCL 16-bit timer/ counter 1 P44/INT24/UCK2 External interrupt 2 (level) P45/INT25/UO2 P46/INT26/UI2 P47/INT27/ADST CMOS I/O port N-ch output CMOS I/O port 1KB RAM/2KB RAM F2MC-8L CPU Wild register 32KB ROM/48KB ROM Other pins MOD0, MOD1, C, VCC, VSS, C/NC 8 10-bit A/D converter Port 5 PWC P36/WTO 20 P20/PWCK Port 4 6-bit PPF03 Port 3 P30/PPG03/MCO Internal databus Reset circuit (watchdog timer) 21-bit time base timer P37/PTO1 12-bit PPG02 Oscillator circuit Clock controller P33/SI1 (UI1) P10 P17 (edge) CMOS I/O port Main clock P32/SO1 (UO1) 8 P00 P07 4 External interrupt 1 12-bit PPG01 RST 8 Clock control Clock prescaler X0 X1 Port 0 Sub clock P63/INT13/X0A Port 1 BLOCK DIAGRAM 8 P50/AN0 P57/AN7 AVCC AVR AVSS MB89530H Series CPU CORE 1. Memory Space The MB89530H series has 64 KB of memory space, containing all I/O, data areas, and program areas. The I/ O area is located at the lowest addresses, with the data area placed immediately above. The data area can be partitioned into register areas, stack areas, or direct access areas depending on the application. The program area is located at the opposite end of memory, closest to the highest addresses, and the highest part of this area is assigned to the tables of interrupt and reset vectors and vector call instructions. The following diagram shows the structure of memory space in the MB89530H series. * Memory Map MB89PV530 MB89P538 MB89538H/538HC MB89537H/537HC 0000H 0000H I/O 0080H I/O 0080H RAM 0100H 0200H General purpose register RAM 0100H 0200H General purpose register 0480H Open 0C80H 0C91H 0880H Open 0C80H Wild register 0C91H Wild register Open Open 4000H 8000H ROM External ROM*1 ROM FFC0H FFFFH FFC0H Vector tables*2 FFFFH Vector tables*2 *1 : The external ROM area is on the MB89PV530 only. *2 : Vector tables (reset, interrupt, vector call instructions) 21 MB89530H Series 2. Registers The F2MC-8L series has two types of registers, dedicated-use registers within the CPU, and general-purpose registers in memory. Program counter (PC) : 16-bit length, shows the location where instructions are stored. Accumulator (A) : 16-bit length, a temporary memory register for calculation operations. The lower byte is used for 8-bit data processing instructions. Temporary accumulator (T) : 16-bit length, performs calculations with the accumulator. The lower byte is used for 8-bit data processing instructions. Index register (IX) : 16-bit length, a register for index modification. Extra pointer (EP) : 16-bit length, a pointer indicating memory addresses. Stack pointer (SP) : 16-bit length, indicates stack areas. Program status (PS) : 16-bit length, contains register pointer and condition code. 16 bits Initial value FFFDH : Program counter PC A : Accumulator Not fixed T : Temporary accumulator Not fixed IX : Index register Not fixed EP : Extra pointer Not fixed SP : Stack pointer Not fixed PS : Program status I-flag = 0, IL1, 0 = 11 Other bits not fixed In addition, the PS register can be divided so that the upper 8 bits are used as a register bank pointer (RP), and the lower 8 bits as a condition code register (CCR). (See the following illustration.) * Program status register configuration 15 PS 14 13 12 RP RP 22 11 7 6 5 4 3 2 1 0 Open Open Open H 10 9 8 I IL1 IL0 N Z V C CCR MB89530H Series The RP register shows the address of the register bank currently being used, so that the RP value and the actual address are related by the conversion rule shown in the following illustration. * General purpose register area real address conversion principle Operation code lower RP upper "0" Address generated "0" "0" "0" "0" "0" A15 A14 A13 A12 A11 A10 "0" "1" R4 A9 A8 A7 R3 A6 R2 A5 R1 A4 R0 A3 b2 A2 b1 b0 A1 A0 The CCR register has bits that show the content of results of calculations and transferred data, and bits that control CPU operation during interrupts. H-flag I-flag IL1, 0 N-flag Z-flag V-flag C-flag : Set to 1 if calculations result in carry or borrow operations from bit 3 to bit 4, otherwise set to 0. This flag is used for decimal correction instructions. : This flag is set to 1 if interrupts are enabled, and 0 if interrupts are prohibited. The default value at reset is 0. : Indicates the level of the currently permitted interrupts. Only interrupt requests having a more powerful level than the value of these bits will be processed. : : : : IL1 IL0 Interrupt level 0 0 0 1 1 0 2 1 1 3 1 Strength Strong Weak Set to 1 if the highest bit is 1 after a calculation, otherwise cleared to 0. Set to 1 if a calculation result is 0, otherwise cleared to 0. Set to 1 if a two's complement overflow results during a calculation, otherwise cleared to 0. Set to 1 if a calculation results in a carry or borrow operation from bit 7, otherwise cleared to 0. This is also the shift-out value in a shift instruction. In addition, the following general purpose registers are available. General purpose registers: 8-bit length, used to contain data. The general purpose registers are 8-bit registers located in memory. There are eight such registers per bank, and the MB89530H series have up to 32 banks for use. The bank currently in use is indicated by the register bank pointer (RP). 23 MB89530H Series *Register bank configuration Address at this location = 0100H + 8 x (RP) R0 R1 R2 R3 R4 R5 R6 R7 32 banks Memory area 24 MB89530H Series I/O MAP Address Register name 00H PDR0 Port 0 data register 01H DDR0 Port 0 direction register 02H PDR1 Port 1 data register 03H DDR1 Port 1 direction register Register description 04H to 06H Write/Read Initial value R/W XXXXXXXXB W 0 0 0 0 0 0 0 0B R/W XXXXXXXXB W 0 0 0 0 0 0 0 0B (Reserved area) 07H SYCC System clock control register R/W X -1 MM1 0 0B 08H STBC Standby control register R/W 0 0 0 1 0 - - -B 09H WDTC Watchdog control register R/W 0 - - - XXXXB 0AH TBTC Time base timer control register R/W 0 0 - - - 0 0 0B 0BH WPCR Clock prescaler control register R/W 0 0 - - - 0 0 0B 0CH PDR2 Port 2 data register R/W XXXXXXXXB 0DH DDR2 Port 2 direction register R/W 0 0 0 0 0 0 0 0B 0EH PDR3 Port 3 data register R/W XXXXXXXXB 0FH DDR3 Port 3 direction register R/W 0 0 0 0 0 0 0 0B 10H PDR4 Port 4 data register R/W XXXX 1 1 XXB 11H DDR4 Port 4 direction register R/W 0 0 0 0 - - 0 0B 12H PDR5 Port 5 data register R/W 11111111B 13H PDR6 Port 6 data register R XXXXXXXXB 14H to 21H (Reserved area) 22H SMC11 Serial mode control register 1 (UART) R/W 0 0 0 0 0 0 0 0B 23H SRC1 Serial rate control register (UART) R/W - - 0 1 1 0 0 0B 24H SSD1 Serial status and data register (UART) R/W 0 0 1 0 0 - 1XB 25H SIDR1/ SODR1 Serial input/output data register (UART) R/W XXXXXXXXB 26H SMC12 Serial mode control register 2 (UART) R/W - - 1 0 0 0 0 1B 27H CNTR1 PWM control register 1 R/W 0 0 0 0 0 0 0 0B 28H CNTR2 PWM control register 2 R/W 0 0 0 - 0 0 0 0B 29H CNTR3 PWM control register 3 R/W - 0 0 0 - - - -B 2AH COMR1 PWM compare register 1 W XXXXXXXXB 2BH COMR2 PWM compare register 2 W XXXXXXXXB 2CH PCR1 PWC pulse width control register 1 R/W 0 0 0 - - 0 0 0B 2DH PCR2 PWC pulse width control register 2 R/W 0 0 0 0 0 0 0 0B 2EH RLBR PWC reload buffer register R/W XXXXXXXXB 2FH SMC21 Serial mode control register 1 (UART/SIO) R/W 0 0 0 0 0 0 0 0B 30H SMC22 R/W 0 0 0 0 0 0 0 0B 31H SSD2 Serial mode control register 2 (UART/SIO) Serial status and data register (UART/SIO) R/W 0 0 0 0 1 - - -B 32H SIDR2/ SODR2 Serial data register (UART/SIO) R/W XXXXXXXXB 33H SRC2 Baud rate generator reload register R/W XXXXXXXXB (Continued) 25 MB89530H Series Address Register name 34H ADC1 35H ADC2 Register description Write/Read Initial value A/D control register 1 R/W 0 0 0 0 0 0 - 0B A/D control register 2 R/W - 0 0 0 0 0 0 1B 36H ADDL A/D data register low R/W XXXXXXXXB 37H ADDH A/D data register high R/W - - - - - - 0 0B 38H PPGC2 PPG2 control register (12-bit PPG) R/W 0 0 0 0 0 0 0 0B 39H PRL22 PPG2 reload register 2 (12-bit PPG) R/W 0X0 0 0 0 0 0B 3AH PRL21 PPG2 reload register 1 (12-bit PPG) R/W XX0 0 0 0 0 0B 3BH PRL23 PPG2 reload register 3 (12-bit PPG) R/W XX0 0 0 0 0 0B 3CH TMCR 16-bit timer control register R/W - - 0 0 0 0 0 0B 3DH TCHR 16-bit timer counter register high R/W 0 0 0 0 0 0 0 0B 3EH TCLR 16-bit timer counter register low R/W 0 0 0 0 0 0 0 0B 3FH EIC1 External interrupt 1 control register 1 R/W 0 0 0 0 0 0 0 0B 40H EIC2 External interrupt 1 control register 2 R/W 0 0 0 0 0 0 0 0B R/W - - - - - - - 0B 41H to 48H 49H (Reserved area) DDCR DDC select register 4AH to 4BH (Reserved area) 4CH PPGC1 PPG1 control register (12-bit PPG) R/W 0 0 0 0 0 0 0 0B 4DH PRL12 PPG1 reload register 2 (12-bit PPG) R/W 0X0 0 0 0 0 0B 4EH PRL11 PPG1 reload register 1 (12-bit PPG) R/W XX0 0 0 0 0 0B 4FH PRL13 PPG1 reload register 3 (12-bit PPG) R/W XX0 0 0 0 0 0B 2 R/W - - - - - 0 0 0B 2 R 0 0 0 0 0 0 0 0B 50H 51H IACR IBSR I C address control register I C bus status register 2 52H IBCR I C bus control register R/W 0 0 0 0 0 0 0 0B 53H ICCR I2C clock control register R/W 0 0 0 XXXXXB 2 R/W - XXXXXXXB 2 R/W XXXXXXXXB 54H IADR I C address register 55H IDAR I C data register 56H EIE2 External interrupt 2 control register R/W 0 0 0 0 0 0 0 0B 57H EIF2 External interrupt 2 flag register R/W - - - - - - - 0B 58H RCR1 6-bit PPG control register 1 R/W 0 0 0 0 0 0 0 0B 59H RCR2 6-bit PPG control register 2 R/W 0X0 0 0 0 0 0B 5AH CKR Clock output control register R/W - - - - - - 0 0B 5BH to 6FH (Reserved area) 70H SMR Serial mode register (SIO) R/W 0 0 0 0 0 0 0 0B 71H SDR Serial data register (SIO) R/W XXXXXXXXB 72H PURR0 Port 0 pull-up resistance register R/W 11111111B 73H PURR1 Port 1 pull-up resistance register R/W 11111111B 74H PURR2 Port 2 pull-up resistance register R/W 11111111B 75H PURR3 Port 3 pull-up resistance register R/W 11111111B 76H PURR4 Port 4 pull-up resistance register R/W 1111--11B (Continued) 26 MB89530H Series (Continued) Address Register name 77H WREN 78H 79H Register description Write/Read Initial value Wild register enable register R/W - - 0 0 0 0 0 0B WROR Wild register data test register R/W - - 0 0 0 0 0 0B PURR6 Port 6 pull-up resistance register R/W ---11111B 7AH (Reserved area) 7BH ILR1 Interrupt level setting register 1 W 1 1 1 1 1 1 1 1B 7CH ILR2 Interrupt level setting register 2 W 1 1 1 1 1 1 1 1B 7DH ILR3 Interrupt level setting register 3 W 1 1 1 1 1 1 1 1B 7EH ILR4 Interrupt level setting register 4 W 1 1 1 1 1 1 1 1B 7FH ITR Interrupt test register C80H WRARH1 Upper address setting register 1 R/W XXXXXXXX Access prohibited XXXXXX0 0B C81H WRARL1 Lower address setting register 1 R/W XXXXXXXX C82H WRDR1 Data setting register 1 R/W XXXXXXXX C83H WRARH2 Upper address setting register 2 R/W XXXXXXXX C84H WRARL2 Lower address setting register 2 R/W XXXXXXXX C85H WRDR2 Data setting register 2 R/W XXXXXXXX C86H WRARH3 Upper address setting register 3 R/W XXXXXXXX C87H WRARL3 Lower address setting register 3 R/W XXXXXXXX C88H WRDR3 Data setting register 3 R/W XXXXXXXX C89H WRARH4 Upper address setting register 4 R/W XXXXXXXX C8AH WRARL4 Lower address setting register 4 R/W XXXXXXXX C8BH WRDR4 Data setting register 4 R/W XXXXXXXX C8CH WRARH5 Upper address setting register 5 R/W XXXXXXXX C8DH WRARL5 Lower address setting register 5 R/W XXXXXXXX C8EH WRDR5 Data setting register 5 R/W XXXXXXXX C8FH WRARH6 Upper address setting register 6 R/W XXXXXXXX C90H WRARL6 Lower address setting register 6 R/W XXXXXXXX C91H WRDR6 Data setting register 6 R/W XXXXXXXX * Description of write/read symbols : R/W : read/write enabled R : Read only W : Write only * Description of initial values : 0 : This bit initialized to "0". 1 : This bit initialized to "1". X : The initial value of this bit is not determined. M : The initial value of this bit is a mask option. - : This bit is not used. Note : Do not use reserved spaces. 27 MB89530H Series ELECTRICAL CHARACTERISTICS 1. Absolute Maximum Ratings Parameter Supply voltage Symbol (AVss = Vss = 0 V) Rating Unit Max VCC, AVCC VSS - 0.3 VSS + 6.0 V AVR VSS - 0.3 VSS + 6.0 V MB89537H/538H* MB89537HC/538HC MB89P538 MB89PV530 VSS - 0.3 VCC + 0.3 V Other than P42, P43 VSS - 0.3 VSS + 6.0 V P42, P43 VSS - 0.3 VCC + 0.3 V Other than P42, P43 VSS - 0.3 VSS + 6.0 V P42, P43 Input voltage VI Output voltage VO "L" level maximum output current IOL 15 mA "L" level average output current IOLAV 4 mA "L" level maximum total output current IOL 100 mA "L" level average total output current IOLAV 40 mA "H" level maximum output current IOH -15 mA "H" level average output current IOHAV -4 mA "H" level maximum total output current IOH -50 mA "H" level average total output current IOHAV -20 mA Current consumption PD 300 mW Operating temperature TA -40 +85 C Tstg -55 +150 C Storage temperature Remarks Min Average value (operating current x operating duty) Average value (operating current x operating duty) Average value (operating current x operating duty) Average value (operating current x operating duty) * : AVcc and Vcc are to be used at the same potential. AVR should not exceed AVcc + 0.3V. WARNING: Semiconductor devices can be permanently damaged by application of stress (voltage, current, temperature, etc.) in excess of absolute maximum ratings. Do not exceed these ratings. 28 MB89530H Series 2. Recommended Operating Conditions Parameter Supply voltage Operating temperature Symbol (AVss = Vss = 0 V) Value Unit Remarks Min Max 3.5* 5.5 V 3.0 5.5 V 2.7* 5.5 V Range warranted for normal operation 1.5 5.5 V RAM status in stop mode AVR 3.5 AVCC V TA -40 +85 C VCC, AVCC Range warranted for normal operation MB89537H/538H MB89537HC/ RAM status in stop mode 538HC MB89P538 MB89PV530 * : Varies according to frequency used, and instruction cycle. See "Operating voltage vs. operating frequency" and "5. A/D Converter Electrical Characteristics". 29 MB89530H Series Operating voltage vs. operating frequency Range of warranted analog precision : VCC = AVCC = 3.5 V to 5.5 V : MB89537H/ MB89538H/ MB89537HC/ MB89538HC 5.5 5.0 Operating voltage VCC (V) : MB89P538/ MB89PV530 4.0 3.5 3.0 2.7 2.0 1.0 0 1.0 2.0 3.0 4.0 5.0 6.0 7.0 8.0 9.0 10.0 11.0 12.0 12.5 0.4 0.32 Operating frequency (MHz) (at instruction cycle = 4 / Fc) 4.0 2.0 0.8 Minimum instruction execution time (Instruction cycles) (s) WARNING: The recommended operating conditions are required in order to ensure the normal operation of the semiconductor device. All of the device's electrical characteristics are warranted when the device is operated within these ranges. Always use semiconductor devices within their recommended operating condition ranges. Operation outside these ranges may adversely affect reliability and could result in device failure. No warranty is made with respect to uses, operating conditions, or combinations not represented on the data sheet. Users considering application outside the listed conditions are advised to contact their FUJITSU representatives beforehand. 30 MB89530H Series 3. DC Characteristics Parameter "H" level input voltage (AVCC = VCC = 5.0 V, AVss = Vss = 0 V, TA = -40 C to +85 C) Value Pin name Condition VIH P00 to P07, P10 to P17, P20 to P27, P30 to P37, P40 to P47, P60 to P64, SI1, SI2 VIHS RST, MOD0, MOD1, INT20 to INT27, UCK1, UI1, INT10 to INT13, SCK1, EC, PWCK, PWC, SCK2, UCK2, UI2, ADST Symbol Unit Typ Max 0.7 VCC VCC + 0.3 V 0.8 VCC VCC + 0.3 V VSS + 1.4 VSS + 5.5 V With SMB input buffer selected* 0.7 VCC VSS + 5.5 V With I2C input buffer selected* VIL P00 to P07, P10 to P17, P20 to P27, P30 to P37, P40 to P47, P60 to P64, SI1, SI2 VSS - 0.3 0.3 VCC V VILS RST, MOD0, MOD1, INT20 to INT27, UCK1, UI1, INT10 to INT13, SCK1, EC, PWCK, PWC, SCK2, UCK2, UI2, ADST VSS - 0.3 0.2 VCC V VSS - 0.3 VSS + 0.6 V With SMB input buffer selected* VSS - 0.3 0.3 VCC V With I2C input buffer selected* VSS - 0.3 VCC + 0.3 V VSS + 5.5 V 4.0 V 0.4 V VIHSMB SCL, SDA VIHI2C "L" level input voltage VILSMB SCL, SDA VILI2C Open drain output applied voltage "H" level output voltage VD1 P50 to P57 VD2 P42, P43 VOH P00 to P07, P10 to P17, IOH = P20 to P24, P30 to P37, -2.0 mA P40, P41, P44 to P47 P25 to P27 "L" level output voltage Remarks Min VOL IOH = -3.0 mA P00 to P07, P10 to P17, P20 to P27, P30 to P37, IOL = P40 to P47, P50 to P57, 4.0 mA RST (Continued) 31 MB89530H Series (AVCC = VCC = 5.0 V, AVss = Vss = 0 V, TA = -40 C to +85 C) Parameter Symbol Pin name Condition Unit Remarks +5 A With no pull-up resistance specified +5 A Min Typ Max P00 to P07, P10 to P17, P20 to P27, P30 to P37, 0.0 V < VI < P40 to P47, P50 to P57, VCC P60 to P64 -5 0.0 V < VI < VSS + 5.5 V Input leak current (Hi-Z output leak current) ILI Open drain output leak current ILIOD P42, P43 RPULL P00 to P07, P10 to P17, P20 to P27, P30 to P37, VI = 0.0 V P40, P41, P44 to P47, P60 to P64, RST Pull-up resistance Value With pull-up resistance is selected. The RST signal is excluded. 25 50 100 k 15 20 mA MB89P538/PV530 ICC1 FCH = 10.0 MHz VCC = 5.0 V tinst = 0.4 s 6 10 mA 5 8.5 mA MB89P538/PV530 ICC2 FCH = 10.0 MHz VCC = 5.0 V tinst = 6.4 s 1.5 3 mA MB89537H/538H MB89537HC/538HC 5 7 mA Sleep mode MB89P538/PV530 ICCS1 FCH = 10.0 MHz VCC = 5.0 V tinst = 0.4 s 2 4 Sleep mode mA MB89537H/538H MB89537HC/538HC FCH = 10.0 MHz VCC = 5.0 V tinst = 6.4 s 1.5 3 mA 1 2 Sleep mode mA MB89537H/538H MB89537HC/538HC 3 7 mA Sub mode MB89P538/PV530 20 50 A Sub mode MB89537H/538H MB89537HC/538HC 30 50 A Sub, sleep modes MB89P538/PV530 15 30 A Sub, sleep modes MB89537H/538H MB89537HC/538HC Supply current VCC ICCS2 ICCL ICCLS FCL = 32.768 kHz VCC = 5.0 V FCL = 32.768 kHz VCC = 5.0 V MB89537H/538H MB89537HC/538HC Sleep mode MB89P538/PV530 (Continued) 32 MB89530H Series (Continued) Parameter ICCT Supply current Pin name Symbol VCC ICCH IA AVCC IAH Input capacitance CIN Except VCC, VSS, AVCC, AVSS Condition Value Unit Remarks 15 A Clock mode, main stop 3 10 A Sub, stop modes 4 6 mA A/D conversion running TA = +25 C 1 5 A A/D stopped f = 1 MHz 10 pF Min Typ Max FCL = 32.768 kHz VCC = 5.0 V 5 TA = +25 C FCH = 10.0 MHz * : MB89PV530/P538/537HC/538HC have a built-in I2C function, and a choice of input buffers by software setting. MB89537H/538H have no built-in I2C functions, and therefore this standard does not apply. 33 MB89530H Series 4. AC Characteristics (1) Reset Timing (VCC = 5.0 V, AVss = Vss = 0 V, TA = -40 C to +85 C) Parameter RST "L" pulse width Symbol Condition tZLZH Value Min Max 48 tHCLY Unit Remarks ns Note : tHCLY is the main clock oscillator period. tZLZH RST 0.2 VCC 0.2 VCC (2) Power-on Reset (AVss = Vss = 0 V, TA = -40 C to +85 C) Parameter Power on time Power shutoff time Symbol Condition tR tOFF Value Unit Min Max 0.5 50 ms 1 ms Remarks For repeated operation Note : Be sure that the power supply will come on within the selected oscillator stabilization period. Also, when varying the supply voltage during operation, it is recommended that the supply voltage be increased gradually. tR tOFF 3.5 V VCC 0.2 V 34 0.2 V 0.2 V MB89530H Series (3) Clock Timing Standards (AVss = Vss = 0 V, TA = -40 C to +85 C) Parameter Clock frequency Clock cycle time Input clock pulse width Input clock rise, fall time Symbol Pins FCH Condition Value Unit Remarks Min Typ Max X0, X1 1 12.5 FCL X0A, X1A 32.768 kHz Sub clock tHCYL X0, X1 80 1000 ns Main clock tLCYL X0A, X1A 30.5 s Sub clock PWH PWL X0 20 ns External clock PWHH PWLL X0A 15.2 s External clock tCR tCF X0 10 ns External clock MHz Main clock * X0, X1 timing and application conditions tHCYL PWH PWL tCR tCF 0.8 VCC 0.8 VCC X0 0.2 VCC 0.2 VCC 0.2 VCC * Clock application conditions Using a crystal oscillator or ceramic oscillator X0 X1 X0 FCH C1 Using an external clock signal C2 X1 Open FCH 35 MB89530H Series * X0A, X1A timing and application conditions tLCYL PWLH PWLL tCR tCF 0.8 VCC 0.8 VCC X0A 0.2 VCC 0.2 VCC 0.2 VCC * Clock application conditions Using a crystal oscillator or ceramic oscillator X0A Using an external clock signal X1A X0A Open FCL C1 FCL C2 (4) Instruction Cycle Parameter Instruction cycle (minimum instruction execution time) 36 X1A (AVss = Vss = 0 V, TA = -40 C to +85 C) Symbol Rated value Unit Remarks 4/FCH, 8/FCH, 16/FCH, 64/FCH s Operating at FCH = 12.5 MHz (4/FCH) tinst = 0.32 s 2/FCL s Operating at FCL = 32.768 kHz tinst = 61.036 s tinst MB89530H Series (5) Serial I/O Timing (VCC = 5.0 V, AVss = Vss = 0 V, TA = -40 C to +85 C) Symbol Pin name Serial clock cycle time tSCYC SCK, UCK SCKSO tSLOV SCK, SO, UCK, UO Valid SISCK tIVSH SI, SCK, UI, UCK SCKvalid SI hold time tSHIX SCK, SI, UCK, UI Serial clock "H" pulse width tSHSL Serial clock "L" pulse width tSLSH SCKSO time tSLOV SCK, SO, UCK, UO Valid SISCK tIVSH SI, SCK, UI, UCK SCK valid SI hold time tSHIX SCK, SI, UCK, UI Parameter Condition Internal clock operation SCK, UCK External clock operation Value Unit Min Max 2 tinst s -200 + 200 ns 200 ns 200 ns 1 tinst s 1 tinst s 0 200 ns 200 ns 200 ns Remarks Note : For tinst see " (4) Instruction Cycle". Internal shift clock mode tSCYC SCK UCK 2.4 V 0.8 V 0.8 V tSLOV SO UO 2.4 V 0.8 V tIVSH tSHIX 0.8 VCC 0.2 VCC SI UI 0.8 VCC 0.2 VCC External shift clock mode tSLSH tSHSL SCK UCK 0.8 VCC 0.2 VCC 0.8 VCC 0.2 VCC tSLOV SO UO 2.4 V 0.8 V tIVSH SI UI 0.8 VCC 0.2 VCC tSHIX 0.8 VCC 0.2 VCC 37 MB89530H Series (6) Peripheral Input Timing Parameter (VCC = 5.0 V, AVss = Vss = 0 V, TA = -40 C to +85 C) Symbol Pin name Peripheral input "H" level pulse width 1 tILIH1 Peripheral input "L" level pulse width 1 tIHIL1 INT10 to INT13, INT20 to INT27, EC, PWC, PWCK Peripheral input "H" level pulse width 2 tILIH2 Peripheral input "L" level pulse width 2 tIHIL2 Value Condition Max 2 tinst s 2 tinst s 28 tinst s 28 tinst s ADST Note : For tinst see " (4) Instruction Cycle". tIHIL1 EC, INT, PWC, PWCK tILIH1 0.8 VCC 0.2 VCC tILIH2 0.8 VCC 0.2 VCC 0.8 VCC 0.2 VCC tIHIL2 ADST 38 Unit Min 0.2 VCC 0.8 VCC Remarks MB89530H Series (7) I2C Timing (VCC = 5.0 V, AVss = Vss = 0 V, TA = -40 C to +85 C) Symbol Pin name Condition Start condition output tSTA SCL SDA Stop condition output tSTO SCL SDA Start condition detection tSTA SCL SDA Stop condition detection tSTO Restart condition output Restart condition detection Parameter Value Min Max 1 / 4 tinst x m x n - 20 1 / 4 tinst x m x n + 20 Unit Remarks ns Master only 1 / 4 tinst x 1 / 4 tinst x (m x n + 8) - 20 (m x n + 8) + 20 ns Master only 1 / 4 tinst x 6 + 40 ns SCL SDA 1 / 4 tinst x 6 + 40 ns tSTASU SCL SDA 1 / 4 tinst x 1 / 4 tinst x (m x n + 8) - 20 (m x n + 8) + 20 ns tSTASU SCL SDA 1 / 4 tinst x 4 + 40 ns SCL output "L" width tLOW SCL 1 / 4 tinst x m x n - 20 1 / 4 tinst x m x n + 20 ns Master only SCL output "H" width tHIGH SCL 1 / 4 tinst x 1 / 4 tinst x (m x n + 8) - 20 (m x n + 8) + 20 ns Master only SDA output delay time tDO SDA 1 / 4 tinst x 4 - 20 1 / 4 tinst x 4 + 20 ns Setup after SDA output interrupt interval tDOSU SDA 1 / 4 tinst x 4 - 20 ns SCL input "L" width tLOW SCL 1 / 4 tinst x 6 + 40 ns SCL input "H" width tHIGH SCL 1 / 4 tinst x 2 + 40 ns SDA input setup tSU SDA 40 ns SDA input hold tHO SDA 0 ns Master only Notes : * For tinst see " (4) The Instruction Cycle". * The value "m" in the above table is the value from the shift clock frequency setting bits (CS4CS3) in the clock control register "ICCR". For details, refer to the register description in the hardware manual. * The value 'n' in the above table is the value from the shift clock frequency setting bits (CS2-CS0) in the clock control register "ICCR". For details, refer to the register description in the hardware manual. * tDOSU appears when the interrupt period is longer than the SCL "L" width. * The rated values for SDA and SCL assume a start up time of 0 ns. 39 MB89530H Series * I2C interface [Data sending (master/slave) ] tSU tDO tDO tSU tDOSU SDA ACK tSTASU tSTA tLOW SCL tHO 1 9 * I2C interface [Data receiving (master/slave) ] tHO tSU tDO tDO tDOSU SDA ACK tHIGH tLOW tSTO SCL 6 40 7 8 9 MB89530H Series 5. A/D Converter Electrical Characteristics (1) MB89537H/538H/537HC/538HC Parameter (VCC = 3.5 V to 5.5 V, AVSS = VSS = 0 V, TA = -40 C to +85 C) Symbol Pin name Condition Resolution capability Total error Linear error Differential linear error Zero transition voltage VOT Full scale transition voltage VFST Analog input voltage VAIN Reference voltage Reference voltage supply current IR IRH 10 bit 5.0 LSB 2.5 LSB 1.9 LSB mV 4.0 LSB 60 tinst s 16 tinst s 10 A AVSS AVR V AVSS + 3.5 AVCC V A/D running 400 A A/D off 5 A AN0 to AN7 AVR Max AVR - 6.5 AVR - 1.5 AVR + 1.5 LSB LSB LSB Sampling time IAIN Typ mV Analog input current Unit Min AVR = AVCC AVSS - 3.5 AVSS + 0.5 AVSS + 4.5 LSB LSB LSB Inter-channel variation Conversion time Value Remarks * * : Includes sampling time Note : For tinst see " (4) The Instruction Cycle". 41 MB89530H Series (2) MB89P538/PV530 Parameter (VCC = 3.5 V to 5.5 V, AVSS = VSS = 0 V, TA = -40 C to +85 C) Symbol Pin name Condition Resolution capability Total error Linear error Differential linear error Zero transition voltage VOT Full scale transition voltage VFST Analog input voltage VAIN Reference voltage Reference voltage supply current IR IRH 10 bit 3.0 LSB 2.5 LSB 1.9 LSB 4.0 LSB 60 tinst s 16 tinst s 10 A 0 AVR V AVSS + 3.5 AVCC V A/D running 400 A A/D off 5 A * : Includes sampling time Note : For tinst see " (4) The Instruction Cycle". 42 mV AN0 to AN7 AVR Max AVR - 3.5 AVR - 1.5 AVR + 1.5 LSB LSB LSB Sampling time IAIN Typ mV Analog input current Unit Min AVR = AVCC AVSS - 1.5 AVSS + 0.5 AVSS + 2.5 LSB LSB LSB Inter-channel variation Conversion time Value Remarks AVCC = VCC * MB89530H Series (3) A/D Converter Terms and Definitions * Resolution The level of analog variation that can be distinguished by the A/D converter. * Linear error (unit : LSB) The deviation between the value along a straight line connecting the zero transition point ("00 0000 0000""00 0000 0001") of a device and the full-scale transition point ("11 1111 1110""11 1111 1111") , compared with the actual conversion values obtained. * Differential linear error (Unit : LSB) The deviation from the theoretical input voltage required to produce a change of 1 LSB in output code. * Total error (Unit : LSB) The difference between theoretical conversion value and actual conversion value. Theoretical input/output characteristics Total error VFST 3FF 3FF 3FE 1.5 LSB 3FD 004 003 3FD Digital output Digital output 3FE VOT 002 Actual conversion characteristics (1 LSB I N + 0.5 LSB) 004 VNT 003 002 1 LSB 001 001 0.5 LSB AVSS AVR AVSS Analog input 1 LSB = VFST - VOT 1022 (V) Actual conversion characteristics Theoretical characteristics AVR Analog input Total error in digital output N = VNT - {1 LSBxN + 0.5 LSB} 1 LSB (Continued) 43 MB89530H Series (Continued) Zero transition error 004 Full-scale transition error Actual conversion characteristics Theoretical characteristics 3FF 002 Actual conversion characteristics 001 Digital output Digital output 003 VOT (actual measurement value) AVSS 3FE 3FD 3FC Analog input Actual conversion characteristics N+1 (1 LSB x N + VOT) 3FD VFST 004 003 002 001 AVSS (actual VNT measurement value) Actual conversion characteristics Theoretical characteristics VOT (actual measurement value) Analog input AVR Analog input linear = VNT - {1 LSB x N + VOT} 1 LSB error in digital output N 44 Actual conversion characteristics AVR Differential linear error Digital output Digital output 3FE VFST (actual measurement value) Analog input Linear error 3FF Actual conversion characteristics Theoretical characteristics Actual conversion V (N + 1) T characteristics N N-1 N-2 AVSS VNT Actual conversion characteristics Analog input AVR Differential linear = V (N + 1) T - VNT -1 1 LSB error in digital output N MB89530H Series (4) Precautionary Information * Input Impedance of Analog Input Pins The A/D converter of MB89530H has a sample & hold circuit as shown below, which uses a sample-and-hold capacitor to obtain the voltage at the analog input pin for 8 instruction cycles following the start of A/D conversion. For this reason if the external circuits providing the analog input signal have high output impedance, the analog input voltage may not stabilize within the analog input sampling time. It is therefore recommended that the output impedance of external circuits be reduced to 10 k or less. * MB89537H/537HC/538H/538HC Analog Input Equivalent Circuit Sample-and-hold circuit C = 31 pF Analog input pin Comparator R = 3.2 k If analog input impedance is 10 k or more, the use of a capacitor of approximately 0.1 F is recommended. Closes 8 instruction cycles after the start of A/D conversion Analog channel selector * MB89P538 and MB89PV530 Analog Input Equivalent Circuit Sample-and-hold circuit C = 64 pF Analog input pin Comparator R = 3 k If analog input impedance is 10 k or more, the use of a capacitor of approximately 0.1 F is recommended. Closes 8 instruction cycles after the start of A/D conversion Analog channel selector * About error The smaller the absolute value |AVR - AVss| is, the greater the relative error becomes. 45 MB89530H Series EXAMPLE CHARACTERISTICS (1) Power Supply Current (External Clock) MB89538H ICCS1 vs. VCC MB89538H ICC1 vs. VCC 3 8 12.5 MHz 2.5 10 MHz 6 10 MHz ICCS1 (mA) ICC1 (mA) 12.5 MHz (TA = 25 C) (TA = 25 C) 8 MHz 4 5 MHz 2 8 MHz 1.5 5 MHz 1 2 MHz 2 2 MHz 0.5 1 MHz 1 MHz 0 0 2 3 4 6 5 2 7 3 4 5 6 7 VCC (V) VCC (V) (2) "H" Level Input Voltage / "L"Level Input Voltage (CMOS Input) MB89538H VIN vs. VCC 4 (TA = 25 C) VIN (V) 3 2 1 0 2 3 4 5 6 7 VCC (V) (3) "H"Level Input Voltage / "L"Level Input Voltage (Hysteresis Input) MB89538H VIN vs. VCC 4 (TA = 25 C) VIH VIN (V) 3 VIL 2 1 0 2 3 4 5 6 7 VCC (V) (Continued) 46 MB89530H Series (Continued) (4) AD Converter Characteristic Example MB89538H Linearity Error 3 2.5 (VCC = AVR = 5 V, Fc = 10 MHz) 2 Error (LSB) 1.5 1 0.5 0 -0.5 -1 -1.5 -2 -2.5 -3 0 128 256 384 512 640 768 896 1024 896 1024 Conversion characteristic MB89538H Differential Linearity Error 2.5 2.5 2 (VCC = AVR = 5 V, Fc = 10 MHz) Error (LSB) 1.5 1 0.5 0 -0.5 -1 -1.5 -2 -2.5 0 128 256 384 512 640 768 Conversion characteristic MB89538H Total Error 4 3 (VCC = AVR = 3 V, Fc = 10 MHz) Error (LSB) 2 1 0 -1 -2 -3 -4 0 128 256 384 512 640 768 896 1024 Conversion characteristic 47 MB89530H Series MASK OPTIONS Part number MB89537H MB89537HC MB89538H MB89538HC MB89P538-101 MB89P538-201 MB89PV530 Method of specification Specify at time of mask order Setting not possible Setting not possible 1 Main clock Select oscillator stabilization wait period (FCH* = 10 MHz) approx.214/FCH* (approx.1.6 ms) approx.217/FCH* (approx.13.1 ms) approx.218/FCH* (approx.26.2 ms) Selection available 218/FCH* (approx. 26.2 ms) 218/FCH* (approx. 26.2 ms) 2 Clock mode selection * 2-system clock mode * 1-system clock mode Selection available No * : FCH : Main clock frequency 48 * 101 : 1-system clock mode 2-system clock mode * 201 : 2-system clock mode MB89530H Series ORDERING INFORMATION Part number Package Remarks MB89537HP MB89537HCP MB89538HP MB89538HCP MB89P538P-101 MB89P538P-201 DIP-64P-M01 MB89537HP and MB89538HP do not have I2C functions. MB89537HPF MB89537HCPF MB89538HPF MB89538HCPF MB89P538PF-101 MB89P538PF-201 FPT-64P-M06 MB89537HPF and MB89538HPF do not have I2C functions. MB89537HPFM MB89537HCPFM MB89538HPFM MB89538HCPFM MB89P538PFM-101 MB89P538PFM-201 FPT-64P-M09 MB89537HPFM and MB89538HPFM do not have I2C functions. MB89537HPFV MB89537HCPFV MB89538HPFV MB89538HCPFV FPT-64P-M03 MB89537HPFV and MB89538HPFV do not have I2C functions. MB89PV530C MDP-64C-P02 MB89PV530CF MQP-64C-P01 49 MB89530H Series PACKAGE DIMENSIONS 64-pin plasic SH-DIP (DIP-64P-M01) Note : Pins width and pins thickness include plating thickness. +0.22 +.009 58.00 -0.55 2.283 -.022 INDEX-1 17.000.25 (.669.010) INDEX-2 +0.70 4.95 -0.20 +.028 .195 -.008 +0.50 0.70 -0.19 +.020 .028 -.007 0.270.10 (.011.004) +0.20 3.30 -0.30 .130 +.008 -.012 1.378 .0543 C +0.40 -0.20 +.016 -.008 1.778(.0700) 0.470.10 (.019.004) 19.05(.750) +0.50 0.25(.010) M 1.00 -0 +.020 0~15 .039 -.0 2001 FUJITSU LIMITED D64001S-c-4-5 Dimensions in mm (inches) (Continued) 50 MB89530H Series 64-pin, Plastic LQFP (FPT-64P-M03) Note : Pins width and pins thickness include plating thickness. 12.000.20(.472.008)SQ 10.000.10(.394.004)SQ 48 0.1450.055 (.006.002) 33 49 32 Details of "A" part 0.08(.003) +0.20 1.50 -0.10 +.008 .059 -.004 INDEX 64 0.100.10 (.004.004) (Stand off) 0~8 17 (Mounting height) "A" LEAD No. 1 16 0.50(.020) C 0.200.05 (.008.002) 0.08(.003) M 0.500.20 (.020.008) 0.600.15 (.024.006) 0.25(.010) 2000 FUJITSU LIMITED F64009S-c-4-7 Dimensions in mm (inches) (Continued) 51 MB89530H Series 64-pin, Plastic QFP (FPT-64P-M06) Note : Pins width and pins thickness include plating thickness. 24.700.40(.972.016) 20.000.20(.787.008) 51 0.170.06 (.007.002) 33 52 32 18.700.40 (.736.016) 14.000.20 (.551.008) INDEX Details of "A" part +0.35 3.00 -0.20 +.014 .118 -.008 64 (Mounting height) 20 0~8 1 19 1.00(.039) 0.420.08 (.017.003) 0.20(.008) +0.15 M 0.25 -0.20 1.200.20 (.047.008) +.006 .010 -.008 (Stand off) "A" 0.10(.004) C 2001 FUJITSU LIMITED F64013S-c-4-4 Dimensions in mm (inches) (Continued) 52 MB89530H Series 64-pin, Plastic QFP (FPT-64P-M09) Note : Pins width and pins thickness include plating thickness. 14.000.20(.551.008)SQ 12.000.10(.472.004)SQ 48 0.1450.055 (.0057.0022) 33 49 32 0.10(.004) Details of "A" part +0.20 1.50 -0.10 +.008 .059 -.004 (Mounting height) 0.25(.010) INDEX 0~8 64 17 1 0.65(.026) C "A" 16 0.320.05 (.013.002) 0.13(.005) 0.500.20 (.020.008) 0.600.15 (.024.006) 0.100.10 (.004.004) (Stand off) M 2001 FUJITSU LIMITED F64018S-c-2-4 Dimensions in mm (inches) (Continued) 53 MB89530H Series 64-pin, Ceramic MDIP (MDP-64C-P02) 0~9 56.900.64 (2.240.025) 15.24(.600) TYP 18.750.30 (.738.012) 2.540.25 (.100.010) 33.02(1.300)REF INDEX AREA 0.250.05 (.010.002) 1.270.25 (.050.010) 10.16(.400)MAX 1.7780.25 (.070.010) C 19.050.30 (.750.012) +0.13 0.46 -0.08 +.005 .018 -.003 55.12(2.170)REF 0.900.13 (.035.005) 3.430.38 (.135.015) 1994 FUJITSU LIMITED M64002SC-1-4 Dimensions in mm (inches) (Continued) 54 MB89530H Series (Continued) 64-pin, Ceramic MQFP (MQP-64C-P01) 18.70(.736)TYP INDEX AREA 16.300.33 (.642.013) 15.580.20 (.613.008) 12.00(.472)TYP +0.40 1.20 -0.20 +.016 .047 -.008 1.000.25 (.039.010) 1.000.25 (.039.010) 1.270.13 (.050.005) 22.300.33 (.878.013) 24.70(.972) TYP 0.30(.012) TYP 1.270.13 (.050.005) 18.120.20 12.02(.473) (.713.008) TYP 10.16(.400) 14.22(.560) TYP TYP 0.30(.012)TYP 7.62(.300)TYP 0.400.10 (.016.004) 18.00(.709) TYP 0.400.10 (.016.004) +0.40 1.20 -0.20 +.016 .047 -.008 9.48(.373)TYP 11.68(.460)TYP 0.50(.020)TYP C 10.82(.426) 0.150.05 MAX (.006.002) 1994 FUJITSU LIMITED M64004SC-1-3 Dimensions in mm (inches) 55 MB89530H Series FUJITSU LIMITED All Rights Reserved. The contents of this document are subject to change without notice. Customers are advised to consult with FUJITSU sales representatives before ordering. The information and circuit diagrams in this document are presented as examples of semiconductor device applications, and are not intended to be incorporated in devices for actual use. Also, FUJITSU is unable to assume responsibility for infringement of any patent rights or other rights of third parties arising from the use of this information or circuit diagrams. The products described in this document are designed, developed and manufactured as contemplated for general use, including without limitation, ordinary industrial use, general office use, personal use, and household use, but are not designed, developed and manufactured as contemplated (1) for use accompanying fatal risks or dangers that, unless extremely high safety is secured, could have a serious effect to the public, and could lead directly to death, personal injury, severe physical damage or other loss (i.e., nuclear reaction control in nuclear facility, aircraft flight control, air traffic control, mass transport control, medical life support system, missile launch control in weapon system), or (2) for use requiring extremely high reliability (i.e., submersible repeater and artificial satellite). Please note that Fujitsu will not be liable against you and/or any third party for any claims or damages arising in connection with above-mentioned uses of the products. Any semiconductor devices have an inherent chance of failure. You must protect against injury, damage or loss from such failures by incorporating safety design measures into your facility and equipment such as redundancy, fire protection, and prevention of over-current levels and other abnormal operating conditions. If any products described in this document represent goods or technologies subject to certain restrictions on export under the Foreign Exchange and Foreign Trade Law of Japan, the prior authorization by Japanese government will be required for export of those products from Japan. F0201 FUJITSU LIMITED Printed in Japan