SPEC NO: DSAK2213 REV NO: V.2 DATE: APR/13/2011 PAGE: 1 OF 6
APPROVED: WYNEC CHECKED: Allen Liu DRAWN: J.Yu ERP: 1201005724
2.2x1.4mm SURFACE MOUNT LED LAMP
Part Number: AA2214SESK Super Bright Orange
Features
z2.2mm x 1.4mm, 1.3mm high.
zLow power consumption.
zAvailable on tape and reel.
zPackage : 2000pcs / reel.
zMoisture sensitivity level : level 3.
zRoHS compliant.
Description
The Super Bright Orange device is made with AlGaInP (on
GaAs substrate) light emitting diode chip.
Package Dimensions
Notes:
1. All dimensions are in millimeters (inches).
2. Tolerance is ±0.2(0.008") unless otherwise noted.
3. The specifications, characteristics and technical data described in the datasheet are subject to change without prior notice.
4. The device has a single mounting surface. The device must be mounted according to the specifications.
SPEC NO: DSAK2213 REV NO: V.2 DATE: APR/13/2011 PAGE: 2 OF 6
APPROVED: WYNEC CHECKED: Allen Liu DRAWN: J.Yu ERP: 1201005724
Handling Precautions
Compare to epoxy encapsulant that is hard and brittle, silicone is softer and flexible. Although its characteristic
significantly reduces thermal stress, it is more susceptible to damage by external mechanical force.
As a result, special handling precautions need to be observed during assembly using silicone encapsulated
LED products. Failure to comply might lead to damage and premature failure of the LED.
1. Handle the component along the side surfaces by using forceps or appropriate tools.
2. Do not directly touch or handle the silicone lens surface. It may damage the internal circuitry.
3. Do not stack together assembled PCBs containing exposed LEDs. Impact may scratch the silicone lens or
damage the internal circuitry.
4.1. The outer diameter of the SMD pickup nozzle should not exceed the size of the LED to prevent air leaks. The inner diame-
ter of the nozzle should be as large as possible.
4.2. A pliable material is suggested for the nozzle tip to avoid scratching or damaging the LED surface during pickup.
4.3. The dimensions of the component must be accurately programmed in the pick-and-place machine to insure precise pickup
and avoid damage during production.
5. As silicone encapsulation is permeable to gases, some corrosive substances such as H2S might corrode silver plating of
leadframe. Special care should be taken if an LED with silicone encapsulation is to be used near such substances.
SPEC NO: DSAK2213 REV NO: V.2 DATE: APR/13/2011 PAGE: 3 OF 6
APPROVED: WYNEC CHECKED: Allen Liu DRAWN: J.Yu ERP: 1201005724
Selection Guide
Notes:
1. θ1/2 is the angle from optical centerline where the luminous intensity is 1/2 of the optical peak value.
2. Luminous intensity/ luminous Flux: +/-15%.
Absolute Maximum Ratings at TA=25°C
Electrical / Optical Characteristics at TA=25°C
Notes:
1.Wavelength: +/-1nm.
2. Forward Voltage: +/-0.1V.
Note:
1. 1/10 Duty Cycle, 0.1ms Pulse Width.
Part No. Dice Lens Type
V
iewing
Angle [1]
Min. Typ. 2θ1/2
AA2214SESK Super Bright Orange (AlGaInP) Water Clear 280 400 120°
Iv (mcd) [2]
@ 20mA
Symbol Parameter Device Typ. Max. Units Test Conditions
λpeak Peak Wavelength Super Bright Orange 610 nm IF=20mA
λD [1] Dominant Wavelength Super Bright Orange 601 nm IF=20mA
Δλ1/2 Spectral Line Half-width Super Bright Orange 29 nm IF=20mA
C Capacitance Super Bright Orange 15 pF VF=0V;f=1MHz
VF [2] Forward Voltage Super Bright Orange 2.1 2.5 V IF=20mA
IR Reverse Current Super Bright Orange 10 uA VR=5V
Parameter Super Bright Orange Units
Power dissipation 75 mW
DC Forward Current 30 mA
Peak Forward Current [1] 195 mA
Reverse Voltage 5 V
Operating Temperature -40°C To +85°C
Storage Temperature -40°C To +85°C
SPEC NO: DSAK2213 REV NO: V.2 DATE: APR/13/2011 PAGE: 4 OF 6
APPROVED: WYNEC CHECKED: Allen Liu DRAWN: J.Yu ERP: 1201005724
Super Bright Orange AA2214SESK
SPEC NO: DSAK2213 REV NO: V.2 DATE: APR/13/2011 PAGE: 5 OF 6
APPROVED: WYNEC CHECKED: Allen Liu DRAWN: J.Yu ERP: 1201005724
AA2214SESK
Reflow soldering is recommended and the soldering profile is shown below.
Other soldering methods are not recommended as they might cause damage to the product.
Reel Dimension Recommended Soldering Pattern
(Units : mm; Tolerance: ± 0.1)
Tape Dimensions
(Units : mm)
SPEC NO: DSAK2213 REV NO: V.2 DATE: APR/13/2011 PAGE: 6 OF 6
APPROVED: WYNEC CHECKED: Allen Liu DRAWN: J.Yu ERP: 1201005724
PACKING & LABEL SPECIFICATIONS AA2214SESK
