Metallized Polypropylene Film EMI Suppression Capacitors R49, Class X1, 310 VAC, 110C Overview Applications The R49 is constructed of metallized polypropylene film encapsulated with self-extinguishing resin in a box of material meeting the requirements of UL 94 V-0. For use as electromagnetic interference, (EMI) suppression filter in across-the-line applications requires X1 safety classification. Intended for the use in situations where exposure to shock in the event of capacitor failure is not possible. Not for use in "series with mains" type applications. X1 classified capacitors are only for the use in a permanently connected apparatus with a connection to mains, which cannot be loosened without the use of a tool. Benefits * Approvals: ENEC, UL, cUL * Class X1 (IEC 60384-14) * Rated voltage: 310 VAC 50/60 Hz * Capacitance range: 0.01 - 2.2 F * Lead spacing: 10.0 - 27.5 mm * Capacitance tolerance: 20%, 10% * Climatic category: 40/110/56, IEC 60068-1 * Tape and reel in accordance with IEC 60286-2 * RoHS Compliant and lead-free terminations * Operating temperature range of -40C to +110C * 100% screening factory test at 2,200 VDC/1,500 VAC * Self-healing properties Click image above for interactive 3D content Open PDF in Adobe Reader for full functionality Part Number System R49 A I 3100 00 01 M Series Rated Voltage (VAC) Lead Spacing (mm) Capacitance Code (pF) Packaging Internal Use Capacitance Tolerance See Ordering Options Table 01 M1 X1, Metallized Polypropylene A = 310 F = 10.0 I = 15.0 N = 22.5 R = 27.5 The last three digits represent significant figures. The first digit specifies number of zeros to be added. K = 10% M = 20% One world. One KEMET (c) KEMET Electronics Corporation * KEMET Tower * One East Broward Boulevard Fort Lauderdale, FL 33301 USA * 954-766-2800 * www.kemet.com F3098_R49_X1_310 * 5/26/2020 1 Metallized Polypropylene Film EMI Suppression Capacitors R49, Class X1, 310 VAC, 110C Ordering Options Table Lead Spacing Nominal (mm) Lead Length (mm) Lead and Packaging Code 4 +2/-0 H0= 18.5 0.5 00 DQ Tape & Reel (Large Reel) H0= 18.5 0.5 CK Bulk (Bag) - Short Leads 3.5 +0.5/-0 JB Bulk (Bag) - Short Leads 4.0 +0.5/-0 JE Bulk (Bag) - Short Leads 3.2 +0.3/-0.2 JH Bulk (Bag) - Long Leads 18 1 JM Bulk (Bag) - Long Leads 30 +5/-0 40 Bulk (Bag) - Long Leads 25 +2/-1 50 30 +5/-0 (sp 8 2) 51 150 5 (sp 8 2) 52 4 +2/-0 H0= 18.5 0.5 00 CK1 30 +5/-0 25 +2/-1 30 +5/-0 (sp 8 2) 150 5 (sp 8 2) 40 50 51 52 4 +2/-0 00 30 +5/-0 25 +2/-1 30 +5/-0 (sp 8 2) 150 5 (sp 8 2) 40 50 51 52 Type of Leads and Packaging Standard Lead and Packaging Options Bulk (Bag) - Short Leads Ammo Pack Other Lead and Packaging Options 10, 15, 22.5 Bulk (Bag) - Insulated Rigid Leads Bulk (Bag) - Insulated Flexible Leads Standard Lead and Packaging Options Bulk (Tray) - Short Leads Tape & Reel (Large Reel) 27.5 Other Lead and Packaging Options Bulk (Tray) - Long Leads Bulk (Tray) - Long Leads Bulk (Bag) - Insulated Rigid Leads Bulk (Bag) - Insulated Flexible Leads Standard Lead and Packaging Options Bulk (Tray) - Short Leads 37.5 1 Other Lead and Packaging Options Bulk (Tray) - Long Leads Bulk (Tray) - Long Leads Bulk (Bag) - Insulated Rigid Leads Bulk (Bag) - Insulated Flexible Leads Not for all sizes, see "Packaging Quantities" table (c) KEMET Electronics Corporation * KEMET Tower * One East Broward Boulevard Fort Lauderdale, FL 33301 USA * 954-766-2800 * www.kemet.com F3098_R49_X1_310 * 5/26/2020 2 Metallized Polypropylene Film EMI Suppression Capacitors R49, Class X1, 310 VAC, 110C Dimensions - Millimeters Loose Insulated Rigid Leads Insulated Flexible Leads 0.5 mm2 FRONT VIEW SIDE VIEW FRONT VIEW SIDE VIEW FRONT VIEW SIDE VIEW L T L T L T H H S H LL B H 8 2 8 2 d p 150 5 35 +0/-5 d L d Nominal Tolerance Nominal Tolerance Nominal Tolerance Nominal Tolerance Nominal Tolerance 10.0 10.0 15.0 15.0 15.0 15.0 15.0 22.5 22.5 22.5 22.5 22.5 27.5 27.5 27.5 27.5 27.5 27.5 0.4 0.4 0.4 0.4 0.4 0.4 0.4 0.4 0.4 0.4 0.4 0.4 0.4 0.4 0.4 0.4 0.4 0.4 5.0 6.0 5.0 6.0 7.5 8.5 10.0 6.0 7.0 8.5 10.0 11.0 9.0 11.0 13.0 14.0 18.0 22.0 +0.2/-0.5 +0.2/-0.5 +0.2/-0.5 +0.2/-0.5 +0.2/-0.5 +0.2/-0.5 +0.2/-0.5 +0.2/-0.5 +0.2/-0.5 +0.2/-0.5 +0.2/-0.5 +0.2/-0.5 +0.2/-0.7 +0.2/-0.7 +0.2/-0.7 +0.2/-0.7 +0.2/-0.7 +0.2/-0.7 11.0 12.0 11.0 12.0 13.5 14.5 16.0 15.0 16.0 17.0 18.5 20.0 17.0 20.0 22.0 28.0 33.0 37.0 +0.1/-0.5 +0.1/-0.5 +0.1/-0.5 +0.1/-0.5 +0.1/-0.5 +0.1/-0.5 +0.1/-0.5 +0.1/-0.5 +0.1/-0.5 +0.1/-0.5 +0.1/-0.5 +0.1/-0.5 +0.1/-0.7 +0.1/-0.7 +0.1/-0.7 +0.1/-0.7 +0.1/-0.7 +0.1/-0.7 13.0 13.0 18.0 18.0 18.0 18.0 18.0 26.5 26.5 26.5 26.5 26.5 32.0 32.0 32.0 32.0 32.0 32.0 +0.2/-0.5 +0.2/-0.5 +0.3/-0.5 +0.3/-0.5 +0.5/-0.5 +0.5/-0.5 +0.5/-0.5 +0.3/-0.5 +0.3/-0.5 +0.3/-0.5 +0.3/-0.5 +0.3/-0.5 +0.3/-0.7 +0.3/-0.7 +0.3/-0.7 +0.3/-0.7 +0.3/-0.7 +0.3/-0.7 0.6 0.6 0.6 0.6 0.6 0.6 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.05 0.05 0.05 0.05 0.05 0.05 0.05 0.05 0.05 0.05 0.05 0.05 0.05 0.05 0.05 0.05 0.05 0.05 Note: See Ordering Options Table for lead length (LL/H 0) options. (c) KEMET Electronics Corporation * KEMET Tower * One East Broward Boulevard Fort Lauderdale, FL 33301 USA * 954-766-2800 * www.kemet.com F3098_R49_X1_310 * 5/26/2020 3 Metallized Polypropylene Film EMI Suppression Capacitors R49, Class X1, 310 VAC, 110C Performance Characteristics Dielectric Plates Winding Leads Protection Related documents Rated Voltage (VR) Polypropylene film Metal layer deposited by evaporation under vacuum Non-inductive type Tinned wire Plastic case, thermosetting resin filled. Box material is solvent resistant and flame retardant according to UL94. IEC 60384-14, EN 60384-14 310 VAC (50/60 Hz), 800 VDC Capacitance Range 0.010 - 2.2 F Capacitance Values E6 series (IEC 60063) Capacitance Tolerance Temperature Range Climatic Category 10%, 20% -40 to +110C 40/110/56 IEC 60068-1 Storage time: 24 months from the date marked on the label package Average relative humidity per year 70% Storage Conditions RH 85% for 30 days randomly distributed throughout the year Dew is absent Temperature: -40 to 80C (see "Maximum Humidity in Storage Conditions" graph below) Approvals Dissipation Factor (tan) Test Voltage Between Terminals ENEC, UL, cUL 0.1% (0.06%*) at 1 kHz, +25C 5C (* typical value) The 100% screening factory test is carried out at 2,200 VDC/1,500 VAC. The voltage level is selected to meet the requirements in applicable equipment standards. All electrical characteristics are checked after the test. It is not permitted to repeat this test as there is a risk to damage the capacitor. KEMET is not liable in such case for any failures. Measured at +25C 5C, according to IEC 60384-2 Insulation Resistance Minimum Values Between Terminals Voltage Charge Voltage Charge Time C 0.33 F C > 0.33 F 1 minute 1 * 10 M ( 5 * 105 M )* 30,000 M * F ( 150,000 M * F )* 100 VDC In DC Applications 5 Recommended voltage 800 VDC * Typical value (c) KEMET Electronics Corporation * KEMET Tower * One East Broward Boulevard Fort Lauderdale, FL 33301 USA * 954-766-2800 * www.kemet.com F3098_R49_X1_310 * 5/26/2020 4 Metallized Polypropylene Film EMI Suppression Capacitors R49, Class X1, 310 VAC, 110C Performance Characteristics cont. Maximum Humidity in Storage Condition 100 Relative Humidity (%) 90 80 70 60 50 40 30 Days Annual Average 30 20 10 0 -40 -20 0 20 40 Temperature (C) 60 80 Impedance Graph (c) KEMET Electronics Corporation * KEMET Tower * One East Broward Boulevard Fort Lauderdale, FL 33301 USA * 954-766-2800 * www.kemet.com F3098_R49_X1_310 * 5/26/2020 5 Metallized Polypropylene Film EMI Suppression Capacitors R49, Class X1, 310 VAC, 110C Environmental Test Data Test IEC Publication Procedure Endurance EN/IEC 60384-14 Vibration IEC 60068-2-6 Test Fc 3 directions at 2 hours each 10 - 55 Hz at 0.75 mm or 98 m/s2 Bump IEC 60068-2-29 Test Eb 1,000 bumps at 390 m/s2 Change of Temperature IEC 60068-2-14 Test Na Upper and lower rated temperature 5 cycles Active Flammability IEC 60384-14 VR +20 surge pulses at 4 kV (pulse every 5 seconds) Passive Flammability IEC 60384-14 IEC 60384-1, IEC 60695-11-5 Needle flame test Damp Heat Steady State IEC 60068-2-78 Test Cab 1.25 x VR VAC 50 Hz, once every hour increase to 1,000 VAC for 0.1 second, 1,000 hours at upper rated temperature +40C and 93% RH, 56 days Approvals Mark Specification File Number EN/IEC 60384-14 CA08.00030 UL 60384-14 and CAN/CSA E60384-14 (310 VAC) E97797 Environmental Compliance All KEMET EMI capacitors are RoHS Compliant. (c) KEMET Electronics Corporation * KEMET Tower * One East Broward Boulevard Fort Lauderdale, FL 33301 USA * 954-766-2800 * www.kemet.com F3098_R49_X1_310 * 5/26/2020 6 Metallized Polypropylene Film EMI Suppression Capacitors R49, Class X1, 310 VAC, 110C Table 1 - Ratings & Part Number Reference Dimensions in mm Capacitance Value (F) B H 0.010 0.015 0.022 0.033 0.010 0.015 0.022 0.033 0.047 0.068 0.068 0.10 0.10 0.15 0.10 0.15 0.22 0.33 0.47 0.33 0.47 0.68 1.0 1.5 2.2 5.0 5.0 6.0 6.0 5.0 5.0 5.0 5.0 6.0 6.0 7.5 7.5 8.5 10.0 6.0 7.0 8.5 10.0 11.0 9.0 11.0 13.0 14.0 18.0 22.0 11.0 11.0 12.0 12.0 11.0 11.0 11.0 11.0 12.0 12.0 13.5 13.5 14.5 16.0 15.0 16.0 17.0 18.5 20.0 17.0 20.0 22.0 28.0 33.0 37.0 Capacitance Value (F) B (mm) H (mm) L Lead Spacing (p) dV/dt (V/s) New KEMET Part Number Legacy Part Number 13.0 13.0 13.0 13.0 18.0 18.0 18.0 18.0 18.0 18.0 18.0 18.0 18.0 18.0 26.5 26.5 26.5 26.5 26.5 32.0 32.0 32.0 32.0 32.0 32.0 10.0 10.0 10.0 10.0 15.0 15.0 15.0 15.0 15.0 15.0 15.0 15.0 15.0 15.0 22.5 22.5 22.5 22.5 22.5 27.5 27.5 27.5 27.5 27.5 27.5 600 600 600 600 500 500 500 500 500 500 500 500 500 500 400 400 400 400 400 200 200 200 200 200 200 49AF2100(1)01(2) 49AF2150(1)01(2) 49AF2120(1)01(2) 49AF2330(1)01(2) 49AI2100(1)01(2) 49AI2150(1)01(2) 49AI2220(1)01(2) 49AI2330(1)01(2) 49AI2470(1)01(2) 49AI2680(1)M1(3) 49AI2680(1)01(2) 49AI3100(1)M1(3) 49AI3100(1)01(2) 49AI3150(1)01(2) 49AN3100(1)01(2) 49AN3150(1)01(2) 49AN3220(1)01(2) 49AN3330(1)01(2) 49AN3470(1)01(2) 49AR3330(1)01(2) 49AR3470(1)01(2) 49AR3680(1)01(2) 49AR4100(1)01(2) 49AR4150(1)01(2) 49AR4220(1)01(2) R49AF2100(1)01(2) R49AF2150(1)01(2) R49AF2120(1)01(2) R49AF2330(1)01(2) R49AI2100(1)01(2) R49AI2150(1)01(2) R49AI2220(1)01(2) R49AI2330(1)01(2) R49AI2470(1)01(2) R49AI2680(1)M1(3) R49AI2680(1)01(2) R49AI3100(1)M1(3) R49AI3100(1)01(2) R49AI3150(1)01(2) R49AN3100(1)01(2) R49AN3150(1)01(2) R49AN3220(1)01(2) R49AN3330(1)01(2) R49AN3470(1)01(2) R49AR3330(1)01(2) R49AR3470(1)01(2) R49AR3680(1)01(2) R49AR4100(1)01(2) R49AR4150(1)01(2) R49AR4220(1)01(2) L (mm) Lead Spacing (p) dV/dt (V/s) New KEMET Part Number Legacy Part Number (1) Insert lead and packaging code. See Ordering Options Table for available options. (2) M = 20%, K = 10% (3) M = 20% (only available tolerance). (c) KEMET Electronics Corporation * KEMET Tower * One East Broward Boulevard Fort Lauderdale, FL 33301 USA * 954-766-2800 * www.kemet.com F3098_R49_X1_310 * 5/26/2020 7 Metallized Polypropylene Film EMI Suppression Capacitors R49, Class X1, 310 VAC, 110C Soldering Process The implementation of the RoHS directive has resulted in the selection of SnAgCu (SAC) alloys or SnCu alloys as primary solder. This has increased the liquidus temperature from that of 183C for SnPb eutectic alloy to 217 - 221C for the new alloys. As a result, the heat stress to the components, even in wave soldering, has increased considerably due to higher pre-heat and wave temperatures. Polypropylene capacitors are especially sensitive to heat (the melting point of polypropylene is 160 - 170C). Wave soldering can be destructive, especially for mechanically small polypropylene capacitors (with lead spacing of 5 mm to 15 mm), and great care has to be taken during soldering. The recommended solder profiles from KEMET should be used. Please consult KEMET with any questions. In general, the wave soldering curve from IEC Publication 61760-1 Edition 2 serves as a solid guideline for successful soldering. Please see Figure 1. Reflow soldering is not recommended for through-hole film capacitors. Exposing capacitors to a soldering profile in excess of the above the recommended limits may result to degradation or permanent damage to the capacitors. Do not place the polypropylene capacitor through an adhesive curing oven to cure resin for surface mount components. Insert through-hole parts after the curing of surface mount parts. Consult KEMET to discuss the actual temperature profile in the oven, if through-hole components must pass through the adhesive curing process. A maximum two soldering cycles is recommended. Please allow time for the capacitor surface temperature to return to a normal temperature before the second soldering cycle. Wave Soldering Recommendations Manual Soldering Recommendations The following is the recommendation for manual soldering with a soldering iron. 300 Second Wave First Wave Temperature (C) Recommended Soldering Temperature 400 350 Soldering Iron Bit Temperature (C) 2+3 seconds max 260C 250 300 200 T< 150C 150 Preheating Cooling ca. 2C/second ca. 3.5C/second typical Tpreheat 100 Typical 250 50 200 150 0 100 0 40 80 120 160 200 240 Time (seconds) 50 0 0 1 2 3 4 5 6 7 8 Soldering Time (seconds) The soldering iron tip temperature should be set at 350C (+10C maximum) with the soldering duration not to exceed more than 3 seconds. (c) KEMET Electronics Corporation * KEMET Tower * One East Broward Boulevard Fort Lauderdale, FL 33301 USA * 954-766-2800 * www.kemet.com F3098_R49_X1_310 * 5/26/2020 8 Metallized Polypropylene Film EMI Suppression Capacitors R49, Class X1, 310 VAC, 110C Soldering Process cont. Wave Soldering Recommendations cont. 1. The table indicates the maximum set-up temperature of the soldering process Figure 1 Dielectric Film Material Maximum Preheat Temperature Maximum Peak Soldering Temperature Capacitor Capacitor Capacitor Capacitor Pitch Pitch Pitch Pitch 15 mm > 15 mm 15 mm > 15 mm Polyester 130C 130C 270C 270C Polypropylene 110C 130C 260C 270C Paper 130C 140C 270C 270C Polyphenylene Sulphide 150C 160C 270C 270C 2. The maximum temperature measured inside the capacitor: Set the temperature so that inside the element the maximum temperature is below the limit: Dielectric Film Material Maximum temperature measured inside the element Polyester 160C Polypropylene 110C Paper 160C Polyphenylene sulphide 160C Temperature monitored inside the capacitor. Selective Soldering Recommendations Selective dip soldering is a variation of reflow soldering. In this method, the printed circuit board with through-hole components to be soldered is preheated and transported over the solder bath as in normal flow soldering without touching the solder. When the board is over the bath, it is stopped and pre-designed solder pots are lifted from the bath with molten solder only at the places of the selected components, and pressed against the lower surface of the board to solder the components. The temperature profile for selective soldering is similar to the double wave flow soldering outlined in this document, however, instead of two baths, there is only one bath with a time from 3 to 10 seconds. In selective soldering, the risk of overheating is greater than in double wave flow soldering, and great care must be taken so that the parts are not overheated. (c) KEMET Electronics Corporation * KEMET Tower * One East Broward Boulevard Fort Lauderdale, FL 33301 USA * 954-766-2800 * www.kemet.com F3098_R49_X1_310 * 5/26/2020 9 Metallized Polypropylene Film EMI Suppression Capacitors R49, Class X1, 310 VAC, 110C Construction Molded Plastic Case Single-sided Metallized Polypropylene Film (First Layer) Detailed Cross Section Molded Plastic Self-Extinguishing Case Resin Single-sided Metallized Polypropylene Film (Second Layer) Margin Margin Metal Contact Layer Metal Contact Layer Margin FILM WINDING SCHEME OPTIONS Leads Single-sided Metallized Polypropylene Film Double-sided Winding Scheme Single-sided Metallized Polypropylene Film 1 Section Single-sided Metallized Polypropylene Film 2 Sections Single-sided Metallized Polypropylene Film 3 Sections Double-sided Metallized Polyester Carrier Film 1 Section Single-sided Metallized Polypropylene Film 4 Sections (c) KEMET Electronics Corporation * KEMET Tower * One East Broward Boulevard Polypro Film Die Metallized Impregnated Paper Metallized Polyphenylene Fort Lauderdale, FL 33301 USA * 954-766-2800 * www.kemet.com Sulfide Film (SMR) Double-sided Metallized Polyester Carrier Film Polyprop Film Die 3 Sections F3098_R49_X1_310 * 5/26/2020 10 Polyp Metallized Polypropylene Film EMI Suppression Capacitors R49, Class X1, 310 VAC, 110C Marking Lead Spacing 10 mm FRONT TOP Capacitance Tolerance Series, Dielectric Code, Safety Class, Self Healing Approval Marks Manufacturer's Logo Capacitance, Rated Voltage IEC Climatic Category Date Code Passive Flammability Category Manufacturing Plant NOTE: Hot imprinting with or without color or ink jet or laser marking Lead Spacing 15 mm, 22.5 mm (small case sizes) FRONT TOP Capacitance Tolerance Series, Dielectric Code, Safety Class, Self Healing Approval Marks Manufacturer's Logo Capacitance, Rated Voltage IEC Climatic Category Date Code Passive Flammability Category: B for volume 1750 mm3 C for volume < 1750 mm3 Manufacturing Plant NOTE: Hot imprinting with or without color or ink jet or laser marking * Differences caused by technology (clichee, laser or ink jet) and production line Lead Spacing 22.5 and 27.5 mm (alternatives*) and 37.5 mm FRONT TOP Series Dielectric Safety Code Class Approval Marks Manufacturer's Logo IEC Climatic Category (c) KEMET Electronics Corporation * KEMET Tower * One East Broward Boulevard Fort Lauderdale, FL 33301 USA * 954-766-2800 * www.kemet.com Self Healing Capacitance, Capacitance Tolerance, Rated Voltage QA Number Passive Flammability Category Manufacturing Date Code F3098_R49_X1_310 * 5/26/2020 Plant 11 IEC Climatic Category Date Code Manufacturing Plant Metallized Polypropylene Film EMI Suppression Capacitors Passive Flammability R49, Class X1, 310 VAC, 110C Category: B for volume 1750 mm3 C for volume < 1750 mm3 NOTE: Hot imprinting with or without color or ink jet or laser marking Marking cont. Lead Spacing 22.5 and 27.5 mm (alternatives*) and 37.5 mm FRONT TOP Series Dielectric Safety Code Class Self Healing Capacitance, Capacitance Tolerance, Rated Voltage Manufacturer's Logo Approval Marks IEC Climatic Category QA Number Passive Flammability Category Manufacturing Plant Date Code * Differences caused by technology (clichee, laser or ink jet) and production line Manufacturing Date Code (IEC 60062) Y = Year, Z = Month Year Code Month Code 2010 2011 2012 2013 2014 2015 2016 2017 2018 2019 2020 2021 2022 2023 2024 2025 2026 2027 2028 2029 2030 A B C D E F H J K L M N P R S T U V W X A January February March April May June July August September October November December 1 2 3 4 5 6 7 8 9 O N D (c) KEMET Electronics Corporation * KEMET Tower * One East Broward Boulevard Fort Lauderdale, FL 33301 USA * 954-766-2800 * www.kemet.com F3098_R49_X1_310 * 5/26/2020 12 Metallized Polypropylene Film EMI Suppression Capacitors R49, Class X1, 310 VAC, 110C Packaging Quantities Lead Spacing (mm) Thickness (mm) Height (mm) Length (mm) Bulk Short Leads Bulk Long Leads Standard Reel o 355 mm Large Reel o 500 mm Ammo Taped 10 5.0 6.0 11.0 12.0 13.0 13.0 1,300 1,000 1,500 1,200 600 500 1,250 1,000 800 680 15 5.0 6.0 7.5 8.5 10.0 11.0 12.0 13.5 14.5 16.0 18.0 18.0 18.0 18.0 18.0 2,000 1,750 1,000 1,000 750 1,000 900 700 500 500 600 500 350 300 300 1,250 1,000 800 700 600 800 680 500 440 380 22.5 6.0 7.0 8.5 10.0 11.0 15.0 16.0 17.0 18.5 20.0 26.5 26.5 26.5 26.5 26.5 805 700 468 396 360 500 500 300 300 250 - - - - - 700 550 450 350 350 464 380 280 235 217 27.5 9.0 11.0 13.0 14.0 18.0 22.0 17.0 20.0 22.0 28.0 33.0 37.0 32.0 32.0 32.0 32.0 32.0 32.0 816 560 480 352 256 168 408 336 288 176 128 112 - - - - - - 450 350 300 - - - - - - - - - (c) KEMET Electronics Corporation * KEMET Tower * One East Broward Boulevard Fort Lauderdale, FL 33301 USA * 954-766-2800 * www.kemet.com F3098_R49_X1_310 * 5/26/2020 13 Metallized Polypropylene Film EMI Suppression Capacitors R49, Class X1, 310 VAC, 110C Lead Taping & Packaging (IEC 60286-2) Figure 1 Lead Spacing 10 mm Figure 2 Lead Spacing 15 mm Figure 3 Lead Spacing 22.5 - 27.5 mm P W2 P2 od A B W W0 W1 H0 P1 P0 F P h h D0 P1 P2 A-B t Taping Specification Dimensions (mm) Description Symbol 10 Fig. 1 Lead Space 15 22.5 Fig. 2 Fig. 3 27.5 Fig. 3 Tol. Lead wire diameter d 0.6 0.6-0.8 0.8 0.8 0.05 Taping lead space P 25.4 25.4 38.1 38.1 1 Feedholeleadspace* P0 12.7 12.7 12.7 12.7 0.2** Centering of the lead wire P1 7.7 5.2 7.8 5.3 0.7 Centeringofthebody P2 12.7 12.7 19.05 19.05 1.3 Leadspacing(pitch)*** F 10 15 22.5 27.5 +0.6/-0.1 Component alignment h 0 0 0 0 2 Height of component from tape center H 0**** 18.5 18.5 18.5 18.5 0.5 Carrier tape width W 18 18 18 18 +1/-0.5 Hold down tape width W0 9 10 10 10 Minimum Hole position W1 9 9 9 9 0.5 Hold down tape position W2 3 3 3 3 Maximum Feed hole diameter D0 4 4 4 4 0.2 Total tape thickness t 0.7 0.7 0.7 0.7 0.2 * 15 mm also available ** Maximum of 1 mm on 20 lead spaces *** Pitches 15 mm and 10 mm taped to 7.5 mm (crimped leads) available upon request **** H0 = 16.5 mm is available upon request (c) KEMET Electronics Corporation * KEMET Tower * One East Broward Boulevard Fort Lauderdale, FL 33301 USA * 954-766-2800 * www.kemet.com F3098_R49_X1_310 * 5/26/2020 14 Metallized Polypropylene Film EMI Suppression Capacitors R49, Class X1, 310 VAC, 110C Lead Taping & Packaging (IEC 60286-2) cont. Ammo Specifications Dimensions (mm) H W T 360 340 59 H T W Reel Specifications Reel Size Standard Large Dimensions (mm) D H W 355 500 30 25 55 Maximum D H W (c) KEMET Electronics Corporation * KEMET Tower * One East Broward Boulevard Fort Lauderdale, FL 33301 USA * 954-766-2800 * www.kemet.com F3098_R49_X1_310 * 5/26/2020 15 Metallized Polypropylene Film EMI Suppression Capacitors R49, Class X1, 310 VAC, 110C KEMET Electronics Corporation Sales Offices Foracompletelistofourglobalsalesoffices,pleasevisitwww.kemet.com/sales. Disclaimer Allproductspecifications,statements,informationanddata(collectively,the"Information")inthisdatasheetaresubjecttochange.Thecustomerisresponsiblefor checkingandverifyingtheextenttowhichtheInformationcontainedinthispublicationisapplicabletoanorderatthetimetheorderisplaced.AllInformationgiven hereinisbelievedtobeaccurateandreliable,butitispresentedwithoutguarantee,warranty,orresponsibilityofanykind,expressedorimplied. StatementsofsuitabilityforcertainapplicationsarebasedonKEMETElectronicsCorporation's("KEMET")knowledgeoftypicaloperatingconditionsforsuch applications,butarenotintendedtoconstitute-andKEMETspecificallydisclaims-anywarrantyconcerningsuitabilityforaspecificcustomerapplicationoruse. TheInformationisintendedforuseonlybycustomerswhohavetherequisiteexperienceandcapabilitytodeterminethecorrectproductsfortheirapplication.Any technicaladviceinferredfromthisInformationorotherwiseprovidedbyKEMETwithreferencetotheuseofKEMET'sproductsisgivengratis,andKEMETassumes noobligationorliabilityfortheadvicegivenorresultsobtained. Although KEMET designs and manufactures its products to the most stringent quality and safety standards, given the current state of the art, isolated component failuresmaystilloccur.Accordingly,customerapplicationswhichrequireahighdegreeofreliabilityorsafetyshouldemploysuitabledesignsorothersafeguards (suchasinstallationofprotectivecircuitryorredundancies)inordertoensurethatthefailureofanelectricalcomponentdoesnotresultinariskofpersonalinjury or property damage. Althoughallproduct-relatedwarnings,cautionsandnotesmustbeobserved,thecustomershouldnotassumethatallsafetymeasuresareindictedorthatother measuresmaynotberequired. KEMET is a registered trademark of KEMET Electronics Corporation. (c) KEMET Electronics Corporation * KEMET Tower * One East Broward Boulevard Fort Lauderdale, FL 33301 USA * 954-766-2800 * www.kemet.com F3098_R49_X1_310 * 5/26/2020 16