SEMICONDUCTOR KIC3211 Series TECHNICAL DATA Analog CMOS Integrated Circuits LOW Noise150mA CMOS High Performance LDO Regulator The KIC3211Series Low Dropout Linear Regulator is ideally suited for portable applications. It offers 1% initial accuracy, B extremely-low dropout voltage(220mV at 150mA, 3.0V Output Type) B1 K and low ground current (typically 75uA). Designed specifically for handheld C A power consumption drops nearly to zero. 1 6 2 5 3 4 A1 TTL-logic-compatible ON/OFF control pin. When disabled, C and battery-powered devices, the KIC3211series provides a The KIC3211Series also works with low-ESR ceramic capacitors, D reducing the amount of board space necessary for power applications, critical in handheld wireless devices. The Line transient response and load transient response of the KIC3211Series are very excellent, thus ICs are very suitable for the power supply for hand-held communication equipment. J H Applications *Cellular phones,Smart Phones, PDA *Battery-powered equipment 1 VIN *Laptop, notebook and palmtop computers 2 GND *Consumer/personal electronics 3 VOUT 4 NC DIM A A1 B B1 C D H J K MILLIMETERS 1.6 +_ 0.1 1.0 +_ 0.05 1.6 +_ 0.05 1.2 +_ 0.05 0.5 0.22 +_ 0.05 0.6(max) 0.125 +_ 0.05 0.3 +_ 0.05 5 GND Features 6 CE *Input voltage range 1.7V to 6.0V *High output accuracy 1.0% accuracy *Low dropout 220mV@150mA 3.0V, Output type SON1612-6 *Stability with ceramic output capacitors *High Ripple Rejection Typ. 70dB(f=1kHz3.0V Output type) *Low ground Current Typ.75A *Quiescent Current Typ. 0.1 A *Excellent Line regulation Typ. 0.02%/V *Built-in Fold Back Protection Circuit Typ. 50mA@Short mode *Stability with ceramic output capacitors Cin=Cout=1.0 Typ. 60dB(f=10kHz3.0V Output type) *TTL-Logic-compatible ON/OFF control input Mark Spec. Out line 6 5 4 1 2 3 4 5 6 No. No. of Mark Marking 1~2 Series Voltage XX 3 4~6 1 2011. 5. 27 2 Device Definition Lot. No. A XXX Description Output Voltage (ex, 33A VOUT=3.3V) Manufacture Year, Week (ex, 924 2009 year 24th week) 3 Revision No : 1 1/9 KIC3211 Series SECLECTION GUIDE The output voltage, package type for the ICs can be selected at the user's request. The selection can be made with designating the part number as shown below; KIC3211XX XXA a Part Number b Code Contents a Dessignation of Package Type: SN : SON1612-6 b Setting Output Voltage (VOUT) : Stepwise setting with a step of 0.1V in the range of 1.2V to 4.0V is possible. Line up Item Output Voltage Marking KIC3211SN12A 1.2V KIC3211SN13A Package Item Output Voltage Marking 12A KIC3211SN27A 2.7V 27A 1.3V 13A KIC3211SN28A 2.8V 28A KIC3211SN14A 1.4V 14A KIC3211SN29A 2.9V 29A KIC3211SN15A 1.5V 15A KIC3211SN30A 3.0V 30A KIC3211SN16A 1.6V 16A KIC3211SN31A 3.1V 31A KIC3211SN17A 1.7V 17A KIC3211SN32A 3.2V 32A KIC3211SN18A 1.8V 18A KIC3211SN33A 3.3V 33A KIC3211SN19A 1.9V 19A KIC3211SN34A 3.4V 34A KIC3211SN20A 2.0V 20A KIC3211SN35A 3.5V 35A KIC3211SN21A 2.1V 21A KIC3211SN36A 3.6V 36A KIC3211SN22A 2.2V 22A KIC3211SN37A 3.7V 37A KIC3211SN23A 2.3V 23A KIC3211SN38A 3.8V 38A KIC3211SN24A 2.4V 24A KIC3211SN39A 3.9V 39A KIC3211SN25A 2.5V 25A KIC3211SN40A 4.0V 40A KIC3211SN26A 2.6V 26A SON1612-6 Package SON1612-6 PIN DESCRIPTIONS SON1612-6 PKG 6 1 2011. 5. 27 5 2 4 3 Pin No. Pin name 1 VDD Input Pin 2 GND Ground Pin 3 VOUT Regulator Output 4 NC 5 GND 6 CE Revision No : 1 Pin Description No connectin Ground Pin Enable/Shutdown (Input) : CMOS compatible input. Logic high=enable, logic low=shutdown. Do not leave open. 2/9 KIC3211 Series Block Diagram VIN ON/OFF Control CE VREF PWTR Error Amp OUT Fold - back Current Limit Block RA Auto Discharge RB Reference Voltage GND Application Circuit VIN OUT VIN KIC3211XXXXA CIN=1.0F Ceramic CE VOUT COUT=1.0F Ceramic GND Shutdown / Enable Stability with ceramic output capacitors Cin = Cout = 1.0 (X7R, X5R) Absolute Maximum Ratings Characteristics Symbol Rating Units Input Voltage VIN 6.0 V Output Current IOUT 300 mA Output Voltage VOUT 1.2 to 4.0 V PD 500 mW Operating Temperature TOPR -40 to +85 Storage Temperature TSTG -65 to +125 Power Dissipation (Note) Note) Package Mounted on FR-4 PCB board (40x40x1.6) 2011. 5. 27 Revision No : 1 3/9 KIC3211 Series Electrical Characteristics (VEN = VIN, Ta = 25) Symbol VIN Parameter Conditions Input Voltage Min Typ Max Units 1.7 - 6.0 V VOUT Output Voltage VIN = Set VOUT + 1V 1mA IOUT 30mA x 0.990 - x 1.010 V IOUT Output Current VIN - VOUT = 1.0V 150 - - mA VOUT = 1.2~1.5 - 0.38 0.70 V VOUT = 1.6~1.7 - 0.36 0.65 V - 0.32 0.55 V 2.1 VOUT 2.7 - 0.28 0.50 V 2.8 VOUT 4.0 - 0.22 0.35 V IOUT = 0mA - 75 95 A IOUT = 150mA - 100 150 A VIN = Set VOUT + 1V VEN = GND (shutdown) - 0.1 1 A - 0.02 0.10 %/V - 22 40 mV - 70 - dB - 60 - dB IOUT = 30mA -40 TOPR 85 - 100 - ppm / VOUT = 0V - 50 - mA CIN = 1.0, COUT = 1.0 BW = 10Hz ~ 100kHz - 30 - Vrms - 1.6 - - V - - - 0.4 V VD IGND IQ Dropout Voltage (Note 1) IOUT = 150mA 1.8 VOUT 2.0 Ground Pin Current (Note 2) Quiescent Current VOUT / VIN Line Regulation VOUT / IOUT Load Regulation RR Ripple Rejection IOUT = 1mA Set VOUT + 0.5V VIN 6.0V VIN = Set VOUT + 1V 1mA IOUT 150mA f = 1kHz Ripple 0.5V p-p VIN - VOUT = 1.0V f = 10kHz VOUT / T Output Voltage Temperature Coefficient ILIM Short Current Limit VNO Output Noise Voltage VEN (ON) VEN (OFF) Output Control Voltage (ON - State) Output Control Voltage (OFF - State) Note 1) Dropout Voltage is defined as the input-to-output differential at which the output voltage drops 2% below its nominal value measured at 1V differential. For outputs below 2.5V, dropout voltage is the input-to-output voltage differential with the minimum input voltage 2.6V Note 2) Ground pin current is the regulator quiescent current. The total current drawn from the supply is the sum of the load current plus the ground pin current. 2011. 5. 27 Revision No : 1 4/9 KIC3211 Series TYPICAL CHARACTERISTICS 1) OUTPUT VOLTAGE vs OUTPUT CURRENT (TOPR = 25) KIC3211SN28 1.4 OUTPUT VOLTAGE VOUT (V) OUTPUT VOLTAGE VOUT (V) KIC3211SN12 1.2 3.5V 1.0 2.5V 0.8 0.6 2.2V 1.7V 0.4 0.2 1.4 1.2 3.8V 4.8V 1.0 0.8 3.5V 0.6 3.1V 0.4 0.0 0.0 0 100 200 300 400 0 500 OUTPUT CURRENT IOUT (mA) 100 200 300 400 500 OUTPUT CURRENT IOUT (mA) OUTPUT VOLTAGE VOUT (V) KIC3211SN40 4.5 4.0 5.0V 3.5 6.0V 3.0 2.5 4.5V 2.0 4.3V 1.5 1.0 0.5 0.0 0 100 200 300 400 500 OUTPUT CURRENT IOUT (mA) 2) OUTPUT VOLTAGE vs INPUT VOLTAGE (TOPR = 25) KIC3211SN28 1.4 OUTPUT VOLTAGE VOUT (V) OUTPUT VOLTAGE VOUT (V) KIC3211SN12 1.3 1.2 1.1 1.0 0.9 IOUT = 1mA IOUT = 30mA 0.8 IOUT = 100mA 2.8 2.7 2.6 2.5 2.4 2.3 IOUT = 1mA 2.2 IOUT = 30mA 2.1 IOUT = 100mA 2.0 0.7 1 2 3 4 5 INPUT VOLTAGE VIN (V) 2011. 5. 27 2.9 Revision No : 1 6 2 3 4 5 6 INPUT VOLTAGE VIN (V) 5/9 KIC3211 Series KIC3211SN40 4.2 4.0 3.8 3.6 3.4 IOUT = 1mA 3.2 IOUT = 30mA IOUT = 100mA 3.0 1 2 3 4 5 6 INPUT VOLTAGE VIN (V) 3) SUPPLY CURRENT vs INPUT VOLTAGE (TOPR = 25) KIC3211SN12 KIC3211SN28 90 90 80 80 70 70 60 60 50 50 40 40 30 30 20 20 10 10 0 0 0 1 2 3 4 5 6 INPUT VOLTAGE VIN (V) 0 1 2 3 4 5 6 INPUT VOLTAGE VIN (V) KIC3211SN40 90 80 70 60 50 40 30 20 10 0 0 1 2 3 4 5 6 INPUT VOLTAGE VIN (V) 2011. 5. 27 Revision No : 1 6/9 KIC3211 Series 4) OUTPUT VOLTAGE vs TEMPERATURE KIC3211SN12 KIC3211SN28 1.23 2.86 1.22 2.84 1.21 2.82 1.20 2.80 1.19 2.78 1.18 2.76 1.17 1.16 -40 -15 10 35 60 85 60 85 2.74 -40 -15 10 35 60 85 KIC3211SN40 4.08 4.06 4.04 4.02 4.00 3.98 3.96 3.94 3.92 -40 2011. 5. 27 -15 10 35 Revision No : 1 7/9 KIC3211 Series 5) RIPPLE REJECTION vs FREQUENCY(CIN = none) KIC3211SN12 KIC3211SN12 90 90 80 80 70 70 60 60 50 50 40 40 30 30 IOUT = 1mA 20 10 0 0.1 IOUT = 100mA 1 10 100 0 0.1 90 80 80 70 70 60 60 50 50 40 40 30 IOUT = 100mA 1 10 100 10 0 0.1 IOUT = 30mA 3.8 IOUT = 100mA 1 10 100 KIC3211SN40 90 90 80 80 70 70 60 60 50 50 40 40 30 30 IOUT = 1mA 20 2011. 5. 27 100 IOUT = 1mA 20 IOUT = 30mA 3.8 KIC3211SN40 0 0.1 10 30 IOUT = 1mA 20 10 IOUT = 100mA 1 KIC3211SN28 90 0 0.1 IOUT = 30mA 10 KIC3211SN28 10 IOUT = 1mA 20 IOUT = 30mA IOUT = 100mA 1 10 Revision No : 1 IOUT = 1mA 20 IOUT = 30mA 5.0 100 10 0 0.1 IOUT = 30mA 5.0 IOUT = 100mA 1 10 100 8/9 KIC3211 Series 6) INPUT LINE TRANSIENT RESPONSE(IOUT = 30mA, tr = tf = 5us, CIN / COUT = Ceramic 1.0) KIC3211SN12 KIC3211SN28 1.25 1.24 Input Voltage 4 2.85 3 2.84 6 5 Input Voltage 1.23 2 2.83 4 1.22 1 2.82 3 0 2.81 1.21 2 Output Voltage 2.80 1.20 1.19 0 Output Voltage 10 20 30 40 50 60 70 80 2.79 0 90 100 10 20 30 40 50 60 70 80 1 0 90 100 7) LOAD TRANSIENT RESPONSE (tr = tf = 5us, CIN / COUT = Ceramic 1.0) 1.45 150 1.40 100 2.85 150 2.84 100 Input Voltage Input Voltage 1.35 50 2.83 50 1.30 0 2.82 0 2.81 1.25 Output Voltage 1.20 1.15 0 2011. 5. 27 (mA) KIC3211SN28 (mA) KIC3211SN12 2 4 6 8 10 12 14 Revision No : 1 16 18 20 Output Voltage 2.80 2.79 0 2 4 6 8 10 12 14 16 18 20 9/9