73M2901CE V.22bis Single Chip Modem Simplifying System IntegrationTM DATA SHEET DS_2901CE_031 January 2010 DESCRIPTION FEATURES The 73M2901CE low speed modem integrates a data pump, controller, and analog front end in a 3.3 V device with a powerful "AT" command host interface. The modem reduces external component count/cost by incorporating many features like parallel phone detect, Line-In-Use and Ring detection in software without requiring additional components. * * The device is a "one chip fits all" solution for applications including set-top boxes, point-of-sale terminals, automatic teller machines, utility meters, vending machines and smart card readers. Another distinctive feature of this device is pin compatibility with Teridian's flagship embedded hard modems, the 73M2901CL, and the 73M1903 soft modem AFE. This offers customers a cost effective method to design for both hard or soft modem solutions in the same system as a risk-free cost reduction path. Complete support, modem reference designs and error correction software are part of the solution offered by Teridian. Our in-house application engineering team is here to help meet your international certification needs. * * * * * * * * * * * * * * * * Rev. 3.4 True one chip solution for embedded systems As low as 9.5 mA operating with standby and power down mode available Power supply operation from 3.6 V to 2.7 V Data modes and speeds: V.22bis - 2400 bps V.22/Bell212 - 1200 bps V.21/Bell103 - 300 bps V.23 - 1200/75 bps (with PAVI turnaround) Bell202 - 1200 bps Bell202/V23 1200 bps FDX 4-wire operation V.22/Bell 212A/V.22bis synchronous modes International Call Progress support: FCC part 68, CTR21, JATE, etc. DTMF generation and detection Worldwide Caller ID capability U.S. Type I and II support EIA 777A compliant SIA-2000 compliant SMS messaging support On chip hybrid driver Blacklisting capability Line-In-Use and Parallel Pick-Up (911) detection with voltage or low cost energy detection method Incoming ring energy detection through CID path; no optocoupler circuitry required Manufacturing Self Test capability Backward compatible with 73M2901CL Packaging: 32 lead QFN, 32-pin TQFP (c) 2010 Teridian Semiconductor Corporation 1 73M2901CE Data Sheet DS_2901CE_031 Table of Contents 1 Hardware Description .................................................................................................................... 4 1.1 Power Supply ....................................................................................................................... 4 1.2 Low Power Mode .................................................................................................................. 4 1.3 Analog Line / Hybrid Interface ............................................................................................... 4 1.4 Interrupt Pins ........................................................................................................................ 4 1.5 Crystal Oscillator................................................................................................................... 5 1.5.1 Specifying a Crystal ..................................................................................................... 5 1.6 Reset .................................................................................................................................... 5 1.7 Asynchronous and Synchronous Serial Data Interface .......................................................... 5 2 Pinout ............................................................................................................................................. 6 3 Pin Descriptions ............................................................................................................................ 7 3.1 Power Pins ........................................................................................................................... 7 3.2 Analog Interface Pins ............................................................................................................ 7 3.3 Digital Interface Pins ............................................................................................................. 7 3.4 External Interrupt Pins .......................................................................................................... 8 3.5 Oscillator Pins....................................................................................................................... 8 4 Electrical Specifications................................................................................................................ 9 4.1 Absolute Maximum Ratings................................................................................................... 9 4.2 Recommended Operating Conditions.................................................................................... 9 4.3 Receiver ............................................................................................................................... 9 4.4 Transmitter ......................................................................................................................... 10 4.5 Maximum Transmit Level .................................................................................................... 10 4.6 DC Characteristics, Vcc = 3.3 V .......................................................................................... 11 4.6.1 DC Supply Current, VDD = 2.7 V (Battery EOL)......................................................... 11 4.6.2 DC Supply Current , VDD = 3.0 V .............................................................................. 11 4.6.3 DC Supply Current VDD = 3.3 V ................................................................................ 12 4.6.4 DC Supply Current VDD = 3.6 V ................................................................................ 12 5 Firmware Description .................................................................................................................. 13 5.1 Firmware Overview ............................................................................................................. 13 5.2 Firmware Features .............................................................................................................. 13 6 Design Considerations ................................................................................................................ 14 6.1 Layout Considerations ........................................................................................................ 14 6.2 73M2901CE Design Compatibility ....................................................................................... 15 6.3 Telephone Line Interface .................................................................................................... 15 6.4 Functional Considerations ................................................................................................... 16 6.4.1 SMS and V.23 Half Duplex ........................................................................................ 16 6.4.2 Leased Line Mode ..................................................................................................... 16 6.4.3 73M2901CE Energy Ring Detection .......................................................................... 17 6.4.4 Caller ID Mode Changes ........................................................................................... 18 6.4.5 Selectable Answer Tone Frequency Detection ........................................................... 18 6.4.6 73M2901CE S99 Country Code Support ................................................................... 18 7 Reference Designs ...................................................................................................................... 21 7.1 Low Cost Design Using DSP Ring and Status Monitoring .................................................... 21 7.2 Reference Design Using Traditional Hardware Line Monitoring ........................................... 22 8 Modem Performance Characteristics ......................................................................................... 23 8.1 BER versus SNR ................................................................................................................ 23 8.2 BER versus Receive Level .................................................................................................. 23 9 Package Mechanical Drawing ..................................................................................................... 24 9.1 32-Pin QFN ........................................................................................................................ 24 9.2 32-Pin TQFP....................................................................................................................... 25 10 Ordering Information ................................................................................................................... 26 11 Related Documentation ............................................................................................................... 26 12 Contact Information..................................................................................................................... 26 Revision History .................................................................................................................................. 27 2 Rev. 3.4 DS_2901CE_031 73M2901CE Data Sheet Figures Figure 1: 32-Pin QFN Pinout ................................................................................................................ 6 Figure 2: 32-Pin TQFP Pinout .................................................................................................................. 6 Figure 3: Low Cost Design Using DSP Ring and Status Monitoring ........................................................ 21 Figure 4: 73M2901CE Worldwide Demo Board: Daughter Board Schematic .......................................... 22 Figure 5: BER versus SNR .................................................................................................................... 23 Figure 6: BER versus Receive Level ...................................................................................................... 23 Figure 7: 32-Pin QFN Drawing ............................................................................................................... 24 Figure 8: 32-Pin TQFP Drawing ............................................................................................................. 25 Tables Table 1: 73M2901CE QFN and TQFP Pinout........................................................................................... 6 Table 2: Leased Line Initialization Commands ....................................................................................... 16 Table 3: Approximate Thresholds for Energy Ring Detection .................................................................. 17 Table 4: 73M2901CE Order Numbers and Packaging Marks.................................................................. 26 Rev. 3.4 3 73M2901CE Data Sheet DS_2901CE_031 1 Hardware Description The 73M2901CE is designed to operate from a +3.6 to +2.7 volt supply with low power consumption (~30 mW @ 3.0 volts). The modem supports automatic standby idle mode. The modem will also accept a request to power down from the DTE via hardware control. No additional major components are required to complete the modem core logic. The modem provides direct firmware LED support via the port pins (pins 3, 4, 5, 6, 31, and 32). The 73M2901 CE includes the following hardware features: * * * Fully self-contained. "AT" Command interpreter and data pump. User pins available. Synchronous serial data I/O available. * * Asynchronous serial port. On-chip hybrid and line driver. * * Autobaud capability from 300 bps to 9600 bps. Reduced external hardware support required with energy incoming ring detection. 1.1 Power Supply Power is supplied to the 73M2901CE by the VPD and VPA pins. The 73M2901CE is designed for a single +3.6 to +2.7 volt supply and for low power consumption (~30mW @ 3.0 volts). Ground is supplied to the 73M2901CE by the VND and VNA pins. The 73M2901CE has been designed with separated analog and digital supplies to insure the best performance of the part by using separately filtered power supplies. It is recommended that separate locally bypassed traces be used to apply power to the analog supply VPA and the digital supply VPD. 1.2 Low Power Mode The Teridian 73M2901CE supports a low power standby mode. If the low power standby option is enabled, the 73M2901CE will go into a power saving mode when idle. While in this mode, the oscillator will be running and clocks will be supplied to the UART, timers and interrupt blocks, but no clocks will be supplied to the CPU. Instruction processing and activity on the internal busses is halted. Normal operation is resumed when an interruption such as assertion of DTR or RING occurs, a character is sent to the 73M2901CE TXD input, or a reset occurs. 1.3 Analog Line / Hybrid Interface The 73M2901CE provides a differential analog output (TXAP and TXAN) and a single-ended analog input (RXA) with internal A/D and D/A converters. A driver is provided for an internal hybrid function. The internal hybrid driver is capable of driving an external load matching impedance and a line-coupling transformer. The internal hybrid/line driver senses the load and adapts itself to its requirements. The 73M2901CE provides firmware control for a hook relay driver (RELAY) as well as interrupt support for a ring detect opto-coupler (RING). 1.4 Interrupt Pins The external interrupt sources, DTR and RING, come from dedicated input pins of the same name. DTR informs the 73M2901CE that the host has requested the 73M2901CE to perform a specific function. The function of DTR can be changed by "AT" commands (described in the 73M2901CE AT Command User Guide). 4 Rev. 3.4 DS_2901CE_031 73M2901CE Data Sheet RING is used to inform the 73M2901CE that the external DAA circuitry or ring energy detector has detected a ring signal. It will go active when each "RING" message is sent on RXD. In addition, sending any character on the TXD line also generates an internal interrupt. 1.5 Crystal Oscillator The Teridian 73M2901CE single chip modem can use an external 11.0592 MHz reference clock or can generate a clock using only a crystal and two capacitors. If an external clock is used, it should be applied to the OSCIN pin. 1.5.1 Specifying a Crystal The manufacturer of a crystal resonator verifies its frequency of oscillation in a test set-up, but to ensure that the same frequency is obtained in the application, the circuit conditions must be the same. The Teridian 73M2901CE modem requires a parallel mode (anti-resonant) crystal, the important specifications of which are as follows: Mode: Frequency: Frequency tolerance: Temperature drift: Load capacitance: ESR: Drive level: Parallel (anti-resonant) 11.0592 MHz 50 ppm at initial temperature An additional 50 ppm over full range 18 pF to 22 pF 75 max Less than 1 mW The peak voltage level of the oscillator should be checked to assure it will not violate the maximum voltage levels allowed on the oscillator pins. A resistor in series with the crystal can be used, if necessary, to reduce the oscillator's peak voltage levels. Crystals with low ESRs may oscillate at higher than specified voltage levels. 1.6 Reset A reset is accomplished by holding the RESET pin high. To ensure a proper power-on reset, the reset pin must be held high for a minimum of 3 s. At power on, the voltage at VPD, VPA, and RESET must come up at the same time for a proper reset. The signals DCD, CTS and DSR will be held inactive for 25 ms, acknowledging the reset operation, within a 250 ms time window after the reset-triggering event. The 73M2901CE is ready for operation after the 250 ms window and/or after the signals DCD, CTS and DSR become active. 1.7 Asynchronous and Synchronous Serial Data Interface The serial data interface consists of the TXD and RXD data paths (LSB shifted in and out first) and the TXCLK and RXCLK serial synchronous clock outputs associated with the data pins; CTS/RTS flow control; DCD, DSR and DTR. In asynchronous mode, the data is passed at the bit rate (tolerance is +1%, -2.5%). Rev. 3.4 5 73M2901CE Data Sheet DS_2901CE_031 2 Pinout The 73M2901CE is available in a 32-pin QFN or 32-pin TQFP package. Table 1 lists the pins for both packages. Table 1: 73M2901CE QFN and TQFP Pinout 4 DSR 12 TXAP 20 VPD 28 DTR 5 CTS 13 VREF 21 NC 29 USR20 6 RTS 14 VBG 22 VND 30 RING 7 USR11 15 RXA 23 TXD 31 RELAY 8 USR10 16 VNA 24 TXCLK 32 RI VND 1 24 TXCLK VND 1 24 TXCLK VPD 2 23 TXD VPD 2 23 TXD DCD 3 22 VND DCD 3 22 VND DSR 4 21 NC DSR 4 21 NC CTS 5 20 VPD CTS 5 20 VPD RTS 6 19 OSCIN RTS 6 19 OSCIN USR11 7 18 OSCOUT USR11 7 18 OSCOUT USR10 8 17 VND USR10 8 17 VND 12 13 14 15 16 VREF VBG RXA VNA 16 VNA TXAP 15 RXA 11 14 VBG TXAN 13 VREF 10 12 TXAP VPA 11 TXAN 9 10 VPA TERIDIAN 73M2901CE RESET 9 RESET TERIDIAN 73M2901CE Figure 1: 32-Pin QFN Pinout 6 VPD RXCLK 25 27 RXD OSCIN 26 19 RXCLK TXAN 27 11 DTR DCD 28 3 USR20 RXD 29 26 RING OSCOUT 30 18 RELAY VPA 31 10 RI VPD 32 2 VPD VPD 25 25 RXD VND 26 17 RXCLK RESET 27 9 DTR VND 28 1 USR20 Name 29 Pin RING Name 30 Pin RELAY Name 31 Pin RI Name 32 Pin Figure 2: 32-Pin TQFP Pinout Rev. 3.4 DS_2901CE_031 73M2901CE Data Sheet 3 Pin Descriptions 3.1 Power Pins Pin Name Pin Number Type VPA 10 I Positive analog voltage (analog supply) VNA 16 I Negative analog voltage (analog ground) VPD 2, 20, 25 I Positive digital voltage (digital supply) VND 1, 17, 22 I Negative digital voltage (digital ground) 3.2 Description Analog Interface Pins Pin Name Pin Number Type RXA 15 I Receive analog input TXAN 11 O Transmit analog - output TXAP 12 O Transmit analog + output VBG 14 O Analog Band Gap voltage reference (0.1 F to VNA). This pin must not be connected to external circuitry other than the decoupling capacitor. VREF 13 O Analog reference voltage (0.1 F to VNA) 3.3 Description Digital Interface Pins Pin Name Pin Number Type RESET 9 I Reset RXCLK 27 O Receive data synchronous clock, valid on rising edge TXCLK 24 O Transmit data synchronous clock, valid on rising edge TXD 23 I Serial data input from DTE RXD 26 O Serial output to DTE USR10 8 I/O Programmable I/O port. This pin can optionally be used to control an external switch for external Line In Use circuitry. USR11 7 I/O Programmable I/O port. This pin can optionally be used to control an external switch for caller ID operation. RTS 6 I Request to send CTS 5 O Clear to send DSR 4 O Data set ready DCD 3 O Data carrier detect RI 32 O Ring indicator RELAY 31 O Relay driver output USR20 29 I/O Programmable I/O port Rev. 3.4 Description 7 73M2901CE Data Sheet 3.4 DS_2901CE_031 External Interrupt Pins Pin Name Pin Number Type RING 30 I External interrupt - Line interface ring detection circuitry input DTR 28 I External interrupt - DTE DTR signal input 3.5 Description Oscillator Pins Pin Name Pin Number Type OSCIN 19 I Crystal input for internal oscillator, also input for external source OSCOUT 18 O Crystal oscillator output 8 Description Rev. 3.4 DS_2901CE_031 73M2901CE Data Sheet 4 Electrical Specifications 4.1 Absolute Maximum Ratings Parameter Rating Supply Voltage -0.5 V to +4.0 V Pin Input Voltage (except OSCIN) -0.5 V to + 6.0 V Pin Input Voltage (OSCIN) -0.5 V to VPD + 0.5 V Storage Temperature -55 C to 150 C Absolute maximum ratings are stress ratings ONLY, functional operation of the device at these or any other conditions above those indicated in the recommended operation sections of this specification is not implied. Exposure to absolute maximum conditions for extended periods of time may affect reliability. 4.2 Recommended Operating Conditions Parameter Rating Supply Voltage 2.7 V to 3.6 V Oscillator Frequency 11.0592 MHz +/- 50 ppm Operating Temperature -40 C to 85 C 4.3 Receiver Parameter Conditions Min Nominal Max Carrier Detect On Tip and Ring -43 dBm01 Carrier Detect Off Tip and Ring -48 dBm01 Carrier Detect Hysteresis Tip and Ring Receive Level Tip and Ring Idle Channel Noise 0.2 kHz to 4.0 kHz Input Impedance RXA 150 Receive Gain Boost S110 bit 5=1, CID mode 18.8 19.3 19.8 dB Max Input Level at RXA VREF=1.25 V 0.587 0.622 0.658 Vpk Total Harmonic Distortion (THD) 1kHz 450 mVpk on RXA nd rd THD=2 and 3 harmonic -70 -50 dB 2 -43 -70 Units dB -9 dBm01 -65 dB k 1 dBm0 refers to the Teridian recommended line interface (8 dB loss from transmit pins to the line and 5 dB loss from the line to the receiver pin). Results may vary depending on the selected DAA components. 0dBm=0.775 mVrms; dBm=10log(Vrms2/(1mW)(600)) Rev. 3.4 9 73M2901CE Data Sheet 4.4 DS_2901CE_031 Transmitter Parameter Conditions Min Nominal Max Units ITU Guard tone power 550 Hz (relative to carrier) -5 -3.5 -2 dB 1800 Hz (relative to carrier) -8 -6.5 -5 dB Calling Tone 1300 Hz -11 -10 -9 dBm01 Answer Tone power 2225 Hz / 2100 Hz -11 -10 -9 dBm0 1 DTMF Transmit power High band tones -12 -11.5 -11 dBm0 1 Low band tones -13.7 -13.2 -12.7 dBm01 Gain adjust tolerance By step -0.3 0 0.3 dBm01 Total Harmonic Distortion (THD) 1 kHz sine wave at output (TXAP-TXAN) 1.5 Vpk (2.7 dBm) for VREF=1.25 V THD=2nd and 3rd harmonic -50 dB Intermod Distortion At output (TXAP-TXAN) 1 kHz, 1.2 kHz sine waves summed 2 Vpk for VREF=1.25 V Each unwanted frequency component -33 dBm Sum of unwanted frequency components in pass band -20 dB below low tone 30 dB Max Units Power supply rejection ratio 4.5 -30 dBm signal at VPA 300 Hz to 30 kHz measured TXAP to TXAN Maximum Transmit Level Parameter Conditions Min Nominal QAM VREF=1.25 V VPA=3.3 V -9.6 dBm01 DPSK VREF=1.25 V VPA=3.3 V -7.4 dBm01 FSK VREF=1.25 V VPA=3.3 V -5.3 dBm01 DTMF (High Tone) VREF=1.25 V VPA=3.3 V S13=$20, S85=80 -8 -7 dBm01 DTMF (Low Tone) VREF=1.25V VPA=3.3V S13=$20, S85=80 -9.7 -8.7 dBm01 1 dBm0 refers to the Teridian recommended line interface (8 dB loss from transmit pins to the line and 5 dB loss from the line to the receiver pin). Results may vary depending on the selected DAA components. 0dBm=0.775 mVrms; dBm=10log(Vrms2/(1mW)(600)). 10 Rev. 3.4 DS_2901CE_031 4.6 73M2901CE Data Sheet DC Characteristics, Vcc = 3.3 V (Vdd stands for VPD and VPA) Parameter Symbol Input low voltage (except OSCIN) VIL Input low voltage OSCIN Max Unit -0.5 0.8 V VIL -0.5 0.2 Vdd V Input high voltage (except OSCIN) VIH 0.7 Vdd +5.5 V Input high voltage OSCIN VIH 0.7 Vdd Vdd+0.5 V Output low voltage (except OSCOUT) VOL IOL=4 mA 0.45 V Output low voltage OSCOUT VOLOSC IOL=3 mA 0.7 V Output high voltage (except OSCOUT) VOH Conditions Min Nom IOH=-4 mA Vdd-0.45 V Output high voltage OSCOUT VOHOSC IOH=-3 mA Vdd-0.9 V Input leakage current (except OSCIN) IIH Vss. These commands are broken out as follows: Y0 B10 S73-32 C2 R2 S10=255 Clear channel mode (1200 bps) V.23 HDX gated by RTS No 125mS wait between commands DCD follows the raw received carrier Toggle DTR to hang up Disable loss of carrier timeout Note that RTS/CTS flow control cannot be used when using V.23 half duplex since RTS is used to turn the carrier on and off. XON/XOFF flow control should be used instead if flow control is needed. The transmitter RTS to carrier on delay time is 10mS and the off delay is 5mS. 6.4.2 Leased Line Mode One of the drawbacks to the earlier 73M2901 modems is that they are designed primarily for dial-up modem applications. This made it difficult to use them in some non-dial-up designs. The 73M2901CE adds a leased line mode that allows a modem to go into the data mode without having to go through a normal handshake or the need for a connection to another modem. The leased line mode is enabled using the @L1 command in the initialization string. The 73M2901CE leased line mode should not be thought of as limited to only leased line. It is also suited to radio links and any applications where the modem needs to be ready to go when it is first connected. Leased line mode can be used with all modulation modes that are supported by the 73M2901CE. Table 1 shows typical command initialization strings that can be used. Table 2: Leased Line Initialization Commands V22bis LL V22 LL B212 LL B103 LL B202 RX LL B202 TX LL V23 HDX LL V23 TX1200 LL V23 TX75 LL V21 LL 16 ATFS99=1Y6K3C1R2S30=4S70=12S26+4O2@L1 ATFS99=1Y6K3C1R2S30=8@L1 ATFS99=1Y6K3C1R2S30=16@L1 ATFS99=1Y6K3C1R2S30=32@L1 ATFS99=1Y6K3C1R2B4@L1 ATFS99=1Y6K3C1R2B5@L1 ATFS99=1Y0C2R2B10@L1 ATFS99=1Y6K3C1R2B3@L1 ATFS99=1Y6K3C1R2B2@L1 ATFS99=1Y6K3C1R2S30=64@L1 Rev. 3.4 DS_2901CE_031 73M2901CE Data Sheet These commands are broken out as follows: F S99=1 Y0 Y6 K3 C1 C2 R2 S30=n Bn O2 S26+4 S70=12 @L1 Set to factor defaults Set to U.S configuration (default) Used clear channel mode (no speed buffering) Use DTE/DCE speed buffering Use RTS/CTS flow control Use qualified carrier detection Use raw carrier detection Disconnect on DTR toggle Set S30 to a modulation mode Set to modulation mode Respond to retrain requests Enable auto retrain requests Lower retrain request threshold to 12 Leased line mode Once the initialization string is given, the modems are started by sending ATD to one modem and ATA to the other. The modems will then begin sending carriers and look for carrier from the other modem. When the modems disconnect using R2 and DTR, an "OK" result code is sent on RXD. The modem will stop sending carrier at the end of the OK message, the delay time determined by the DTE speed and the time it takes to output the message. It is important to note the auto retrain feature (O2) should be enabled when using V.22bis. V.22bis requires training when it connects and auto retrain is off by default. Make sure "S26+4" is also sent so it can also initiate a retrain as well. 6.4.3 73M2901CE Energy Ring Detection The 73M2901CE has a feature that was added with the intention of lowering the total modem cost by eliminating some of the more expensive external components. The threshold for the ring detector depends on the setting of the S123 register and the components in the Caller ID path, especially the transformer. The number that S123 is set to represents the amplitude threshold of the ring signal (see Table 2). In a conventional ring detect circuit the threshold is set by the hardware, usually the values of the Zener diodes used in the ring detect circuit. Table 3: Approximate Thresholds for Energy Ring Detection Typical US Wet Transformer 20 15 10 5 S123 Register Setting with Frequency Checking Vrms min off to on 45 34 24 12 Vrms min on to off 42 32 22 10 Typical ETSI TS 203 Dry Transformer Design S123 Register Setting with Frequency Checking 20 15 10 5 Vrms min off to on 5 5 5 5 Vrms min on to off 5 5 5 5 3 7 5 3 5 5 Having the ability to set the threshold over a wide range through the S123 register eliminates the need to change components to adjust the ring detection sensitivity. Energy ring detection uses the Caller ID path and coupling transformer to path to pass the incoming ring signal to the modem so it can detect the ring signal using the internal DSP. In an average design this can save at least $0.35 in the total parts cost or even more in lower volume products. The 73M2901CE is still compatible with the earlier 2901 products and still supports the opto-coupled ring detection method, although not on our current demo boards. Wet transformers generally have poorer frequency response in the ring frequency range than dry transformers. This means that the threshold must be sent to a lower number for wet transformers than with some V.90-rated dry transformers. This also means that lower frequency ring signal detection will also require a lower setting. The range of values for S123 can be from 1 to 127 when checking frequency Rev. 3.4 17 73M2901CE Data Sheet DS_2901CE_031 or 129 to 255 when not checking frequency. The practical range is from 3 to 30 when checking frequency, depending on the transformer, Caller ID series resistor, capacitor, and the ring frequency. The other ring parameters such as ring frequency (S17 and S18) and cadence (S51-S58) still need to be programmed when using energy ring detection. The typical initialization string for ring detection and auto answer for the U.S. would be: ATS123=7S0=1 For other countries, the other ring parameters should also be individually programmed, or the S99 register can be used to program all the country parameters. 6.4.4 Caller ID Mode Changes The Caller ID modes have also had some enhancements. There is now two different types of TYPE II caller ID; normal TYPE II and snoop mode TYPE II. Normal TYPE II Caller ID is on when S110 bit 3 is turned on. The modem must be off hook (in use) for this mode to be active. When the modem detects an alerting tone telling it that a call is waiting and that a Caller ID message is about to be sent, the modem then sends a DTMF digit "D" to notify the CO that A TYPE II Caller ID device is present. The CO then sends the Caller ID message, and after receiving the message the 73M2901CE will go on-hook (hang up). TYPE II snoop mode is enabled when S95=$99 (99 hex). In this mode the modem will report either a TYPE I or TYPE II Caller ID message when the modem is on hook. If another Caller ID device is off hook the modem will detect the Caller ID handshake and output the Caller ID data, but the 73M2901CE will not actively participate otherwise. TYPE II Caller ID performance has been improved and, using proper coupling circuitry to monitor the CID signal, the 73M2901CE can pass all EIA-777A tests. 6.4.5 Selectable Answer Tone Frequency Detection It is now possible to select which frequencies will be detected as an answer tone during the handshake. A new S register, S120, has been added for this purpose. This adds some flexibility to the handshake in dial-up applications. The register bit definitions are as follows: Bit 0 1650Hz - V21 Marks (default) Bit 1 1300Hz - V23 Marks Bit 2 2100Hz - ITU Answer Tone (default) Bit 3 Reserved Bit 4 2225Hz - Bell Answer Tone (default) Bit 5 2250Hz - S0 (default) Bit 6 Reserved Bit 7 Reserved 6.4.6 73M2901CE S99 Country Code Support A feature of the 73M2901 family of modem ICs is the country configuration register S99. This register can be used to program a variety of country parameters with a single register setting. See the 73M2901CE AT Command User Guide if the countries you are interested are not listed for S99; the individual parameters can still be programmed through the S-registers. Tables with all the register settings controlled by S99 are provided. By finding the country with the settings closest to what are required, you can minimize the number of registers that need to be programmed. The following information can be used to tailor the behavior of the 73M2901CE for specific support for countries not listed for S99. 18 Rev. 3.4 DS_2901CE_031 73M2901CE Data Sheet 6.4.6.1 Ring Detection Parameters The ring detector is programmable in a number of ways. S-registers S17 and S18 control the frequency range of the ring frequencies that are valid. Ringing tones outside these settings will not be detected. S-registers S51-S58 determine the cadences (on and off timing of the tones) that are allowed. Either one of two different cadences can be accepted or a dual cadence can be defined, depending on the setting of bit 6 in register S29. S123 enables the energy ring detection feature. With S123 set to 0, energy ring detection is disabled and the optocoupler input is used as in the 73M2901CL. With S123 set to a non-zero number, the amplitude threshold and whether the ring frequency is checked can be controlled. 6.4.6.2 Dial Tone Parameters The dial tone parameters can also be controlled over a wide range. S29 controls whether a continuous dial tone (bit 7=1, the default), one of two different single cadences (bit 4=0, default) or a dual cadence (bit 4=1) dial tone will be detected. Registers S35 - S42, control the two cadences' on and off times. There is also control for the tones that are detected as valid. Register S20 controls whether precise frequencies will be detected or a band of frequencies selected as a valid. S20 also selects whether an individual tone or all tones selected by S19 must be detected. The low nibble of register S19 selects which tones will be used for dial tone detection. Register S88 selects the imprecise frequency range for imprecise detection mode. In addition register S66 determines the maximum time to wait for dial tone, S67 the tone qualification duration, and S75 and S77 select the minimum level for detection for imprecise and precise tones, respectively. 6.4.6.3 Busy Tone Parameters The busy tone parameters can also be controlled over a wide range. S29 controls whether one of two different single cadences (bit 5=0, default) or a dual cadence (bit 5=1) dial tone will be detected. Registers S43 - S50, control the two cadences' on and off times. There is also control for the tones that are detected as valid. Register S20 controls whether precise frequencies will be detected or a band of frequencies selected as a valid tone. S20 also selects whether an individual tone or all tones selected by S19 must be detected. The high nibble of register S19 selects which tones will be used for busy tone detection. Register S88 selects the imprecise frequency range for imprecise detection mode. In addition, registers S76 and S78 select the minimum level for detection for imprecise and precise tones, respectively. 6.4.6.4 Pulse Dialing Registers S32 through S34 control the timing of pulse dialing. S32 sets the duration of off hook switch closure (make time). S33 controls the off hook open time (break time). S34 controls the time between digits. S32 and S33 times are in ms, while S34 is in 10 ms increments. Some countries use different pulse patterns to represent the digits, so S72 can be used to set the pulse pattern so digits are correctly sent. The default is the most common, where the digit equals the number of pulses, except for 0, which is 10 pulses. 6.4.6.5 DTMF Dialing DTMF on and off timing can be adjusted by S11. The requirements for the timing can vary with different countries. The DTMF transmit levels can be adjusted using the upper nibble of register S13 and the twist (level of the lower frequency relative to the higher frequency) can be changed using S12 bits 4-6. Additional adjustment of the transmit level is provided by S85, but setting S85 at too high of a level can also increase the THD, so restraint is advised. DTMF should be transmitted at the highest level allowed by country specific limitations, but do not exceed this limit. Rev. 3.4 19 73M2901CE Data Sheet DS_2901CE_031 6.4.6.6 Calling Tone Calling tone is enabled by setting S28 bit 7 to one. S15 sets the calling tone off time in 100 ms increments and S16 sets the calling tone on time in 10 ms increments. 6.4.6.7 Call Progress and Data Carrier Transmit Levels The levels for the carrier and call progress tones (calling tone, answer tone) can be adjusted using the lower nibble of S13. This can be used to compensate for transmit path losses and to adjust for the highest transmit levels allowable with a particular hardware configuration and country limitation. The call progress and data levels can only be changed in 2 dB increments, therefore S13 bit 3 is ignored. 6.4.6.8 Caller ID - Type I and Type II The 73M2901CE supports worldwide Caller ID (CID) standards. Most of the CID controls are in register S95, but some are also found in other registers. Looking for the Japanese CID and Type II snoop mode Marking preamble are controlled by S72 bit 5. S72 bit4 controls Japanese on-hook CID mode. CID wetting pulse control is controlled by S72 bit 3. Type II CID is enabled with S110 bit 3. When a Type II CID message is detected, the modem will go back on hook after the message is retrieved. Register S95 controls all other aspects of the CID mode, such as FSK or DTMF CID, alerting tone detection, the number of line reversals or rings before CID is expected, and enabling CID. There is also a continuous CID mode and a DTMF receive mode without a preceding "CID:" so DTMF digits can be detected. When S95 is set to 99 Hex (ATS95=$99) both US Type I and Type II snoop mode are enabled. 6.4.6.9 ITU Answer Tone Phase Reversals The 73M2901CE supports ITU answer tone 180 phase reversals during the handshake. Setting S92 bit 6 enables phase reversals and is set to zero by default (no phase reversals). 6.4.6.10 1200 BPS Fast Connect Mode The 73M2901CE supports the fast connect handshake used in POS terminal applications. Both Bell 212A and V.22 fast connect are supported for the calling side. It does not support the answering fast connect as exactly defined, but the Ln commands can be used to shorten the handshake time. To use the calling fast connect handshake, Set register S89 bit 5 (ATS89+64) and set register S30 to Bell 212A only (ATS30=16). This applies to both Bell 212A and V.22 since the originating side handshake is the same for both modes. Setting S30 to any other value will override the originate fast connect mode. The originating fast connect mode will send flags instead of marks if the modem is set for synchronous mode (Y1 or Y4). For the answering side, the L1 command will bypass the billing delay and answer tone to significantly speed up the handshake. This will work with the originating Bell 212A or V.22 fast connect or normal connect, as well as the standard V.22 bis connection. Of course the fastest connections will be with Bell 212A and V.22 operating in the fast connect mode. L2 will still use the 2-second billing delay, but the 2-second answer tone will not be sent. L3 will use the normal billing delay, and send a short 400 ms answer tone. L1 will give the fastest handshake with the 1200 bps originate fast connect mode enabled. 20 Rev. 3.4 DS_2901CE_031 73M2901CE Data Sheet 7 Reference Designs 7.1 Low Cost Design Using DSP Ring and Status Monitoring Figure 3: Low Cost Design Using DSP Ring and Status Monitoring Rev. 3.4 21 73M2901CE Data Sheet Reference Design Using Traditional Hardware Line Monitoring -This version supports only: ---Ring-E ---PPU-E ---LIU-E -Keep analog and digital power and ground separate up to J1 connector. -Keep Vref and Vbg traces away from digital traces, especially clocks. Keep traces short and connect Vref and Vbg caps to analog ground. CTR-21 C20 150nF 5 -All resistors 0603 footprint except R25 which is 1206 R24 SOIC14 750 3 4 U2C -EMIT4033 is required for Austalia only; the non-encapsulated MIT4033 can be used for designs not requiring Austalian operation. -To use the programmable termination: For all: S102-3, S104-1, S95-128, S110-64 600 Ohm termination: S101+1, S101-2, S103-1 CTR-21 termination: S101-1, S101+2, S103-1 Australian termination: S101-1, S101-2, S103+1 Note: A termination MUST be programmed or no termination will be activated. 74LVC4066D AUST 12 C25 115nF 11.0592 MHz R26 C2 820 C3 33pF U2B R27 420 U2A R2 5.1K 2K(NC) .047uF C27 1 VREF TXAP TXAN C4 0.002uF(NC) RESET R25 18 1/2W C E C22 3.3uF, 16V 0.1uF C28 220pF, 3kV + C9 C10 HD04 BR1 0.1uF 2 3 U4 TLP627 R8 30K HOOK C1 10uF C18 0.22uF 250V R1 10K F1 3 0.1uF VCC3_3D VCC3_3D 0.1uF + L1 NLV32T-4R7J-PF US600 CTR-21 C6 R12 62K VCC3_3 10uF + R28 47K C26 82nF C24 R16 100 C5 3.3uF B 2 1 R9 30K RING/CIDdetection E1 TISP4350T3BJR Bourns Thy ristor L2 NLV32T-4R7J-PF 4 C8 R13 21K 3.3uF VCC3_3A C7 + B Q2 MMBTA06 Q1 2 RXA VBG 1 16 15 14 13 12 11 10 9 1 2 3 4 5 6 7 8 VND VPD DCD DSR CTS RTS USR11 USR10 VNA RXA VBG VREF TXAP TXAN VPA RESET 74LVC4066D R15 BCP-56 Q3 RING/CID detection 24 23 22 21 20 19 18 17 VPD RXD RXCLK DTR USR20 RING RELAY RI DCDB L4 NLV32T-4R7J-PF VCC3_3 25 26 27 28 AUST 29 30 RELAY B 31 32 2901CE_QFN/TQFP32 TXCLK TXD VND N/C VPD OSCIN OSCOUT VND U1A J1 C21 T1 3.3uF, 25V Sumida EMIT4033 3 2 D2 MMSZ5248BT 18V R20 1 20K 4 MMBTA06 + 2 1 VCC3_3A 2 E 0.1uF L3 NLV32T-4R7J-PF C D1 RS1G 4 2 R17 100 3 0.1uF 1 C14 3.3uF 4 C13 + 13 OSCIN OSCOUT + C12 3.3uF R23 33K VCC3_3D - C11 RXDB DTRB TXDB RIB DCDB DSRB CTSB RTSB 1 74LVC4066D US600 VCC3_3 VCC3_3D 10 9 8 7 6 5 4 3 2 1 D3 MMSZ52C2V4S 10 11 Y1 27pF + 7.2 DS_2901CE_031 C19 C29 220pF, 3kV MF-R015/600 Bourns PTC f use J2 4 3 2 1 RJ-11 0.22uF 250V VCC3_3D Figure 4: 73M2901CE Worldwide Demo Board: Daughter Board Schematic 22 Rev. 3.4 DS_2901CE_031 73M2901CE Data Sheet 8 Modem Performance Characteristics The curves presented in this data sheet define modem IC performance under a variety of line conditions typical of those encountered over the Public Switched Telephone Network. 8.1 BER versus SNR This test represents the ability of the modem to operate over noisy lines with a minimum amount of data transfer errors. Since some noise is generated in the best dial up lines, the modem must operate with the lowest signal to noise ratio (SNR) possible. Better modem performance is indicated by test curves that are closest to the BER axis. A narrow spread between curves representing the four line parameters indicates minimal variation in performance while operating over a range of typical operating conditions. A DPSK or QAM modem will exhibit better BER performance test curves receiving in the low band (answer mode) than in the high band (originate mode). 8.2 BER versus Receive Level This test measures the dynamic range of the modem. Because signal levels vary widely over dial up lines, the widest possible dynamic range is desirable. The SNR is held constant at the indicated values as the receive level is lowered from a very high to a very low signal level. The width of the bowl of these curves, taken at the BER break points is the measure of the dynamic range. Figure 5: BER versus SNR Rev. 3.4 Figure 6: BER versus Receive Level 23 73M2901CE Data Sheet DS_2901CE_031 9 Package Mechanical Drawing 9.1 32-Pin QFN 0.85 NOM./ 0.9MAX. 0.00 / 0.005 5 0.20 REF. 2.5 1 2.5 2 3 5 SEATING PLANE TOP VIEW SIDE VIEW 0.35 / 0.45 3.0 / 3.75 CHAMFERED 0.30 0.18 / 0.3 1.5 / 1.875 1 2 3 3.0 / 3.75 0.25 1.5 / 1.875 0.5 0.2 MIN. 0.35 / 0.45 0.5 0.25 BOTTOM VIEW Figure 7: 32-Pin QFN Drawing 24 Rev. 3.4 DS_2901CE_031 9.2 73M2901CE Data Sheet 32-Pin TQFP Figure 8: 32-Pin TQFP Drawing Rev. 3.4 25 73M2901CE Data Sheet DS_2901CE_031 10 Ordering Information Table 4 lists the order numbers and packaging marks used to identify 73M2901CE products. Table 4: 73M2901CE Order Numbers and Packaging Marks Part Description Order Number Packaging Mark 73M2901CE 32-Pin QFN Lead Free 73M2901CE-IM/F M2901CEM 73M2901CE 32-Pin QFN Lead Free Tape & Reel 73M2901CE-IMR/F M2901CEM 73M2901CE 32-Pin Thin Quad Flat Pack Lead Free 73M2901CE-IGV/F 73M2901CEIGV 73M2901CE 32-Pin Thin Quad Flat Pack Lead Free Tape & Reel 73M2901CE-IGVR/F 73M2901CEIGV 11 Related Documentation The following 73M2901CE documents are available from Teridian Semiconductor Corporation: 73M2901CE AT Command User Guide 73M2901CE Demo Board User Guide 12 Contact Information For more information about Teridian Semiconductor products or to check the availability of the 73M2901CE, contact us at: 6440 Oak Canyon Road Suite 100 Irvine, CA 92618-5201 Telephone: (714) 508-8800 FAX: (714) 508-8878 Email: modem.support@teridian.com For a complete list of worldwide sales offices, go to http://www.teridian.com. 26 Rev. 3.4 DS_2901CE_031 73M2901CE Data Sheet Revision History Revision Date Description 2.2.1 4/20/2004 First publication. 3.1 12/14/2007 Replaced 32QFN punched with SAWN package, removed leaded package option, updated schematic and minor clean up. 3.2 1/21/2008 Changed dimension of bottom exposed pad on 32QFN mechanical package figure. 3.3 4/3/2009 Formatted to new Teridian style. Assigned new document number. Made minor corrections to Section 5.3 and Section 6.3. 3.4 1/15/2010 In Section 6.1, duplicated the hardware design considerations from the 73M2901CE Demo Board User Manual. Moved the 73M2901CE/CL differences from the 73M2901CE Demo Board User Manual to Section 6.4. Replaced the schematics in Figure 3 and Figure 4 with new schematics. Improved the charts in Figure 5 and Figure 6. Miscellaneous editorial changes. Teridian Semiconductor Corporation is a registered trademark of Teridian Semiconductor Corporation. Simplifying System Integration is a trademark of Teridian Semiconductor Corporation. All other trademarks are the property of their respective owners. Teridian Semiconductor Corporation makes no warranty for the use of its products, other than expressly contained in the Company's warranty detailed in the Teridian Semiconductor Corporation standard Terms and Conditions. The company assumes no responsibility for any errors which may appear in this document, reserves the right to change devices or specifications detailed herein at any time without notice and does not make any commitment to update the information contained herein. Accordingly, the reader is cautioned to verify that this document is current by comparing it to the latest version on http://www.teridian.com or by checking with your sales representative. Teridian Semiconductor Corp., 6440 Oak Canyon, Suite 100, Irvine, CA 92618 TEL (714) 508-8800, FAX (714) 508-8877, http://www.teridian.com Rev. 3.4 27 Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Maxim Integrated: 73M2901CE-IM/F 73M2901CE-IMR/F 73M2901CE-IGV/F 73M2901CE-IGVR/F