NLAS4599 Low Voltage Single Supply SPDT Analog Switch The NLAS4599 is an advanced high speed CMOS single pole - double throw analog switch fabricated with silicon gate CMOS technology. It achieves high speed propagation delays and low ON resistances while maintaining low power dissipation. This switch controls analog and digital voltages that may vary across the full power-supply range (from VCC to GND). The device has been designed so the ON resistance (RON) is much lower and more linear over input voltage than RON of typical CMOS analog switches. The channel select input is compatible with standard CMOS outputs. The channel select input structure provides protection when voltages between 0 V and 5.5 V are applied, regardless of the supply voltage. This input structure helps prevent device destruction caused by supply voltage - input/output voltage mismatch, battery backup, hot insertion, etc. * * * * * * * * * * http://onsemi.com MARKING DIAGRAMS TSOP-6 DT SUFFIX CASE 318G 1 1 6 SC-88 DF SUFFIX CASE 419B 1 Channel Select Input Over-Voltage Tolerant to 5.5 V Fast Switching and Propagation Speeds Break-Before-Make Circuitry Low Power Dissipation: ICC = 2 A (Max) at TA = 25C Diode Protection Provided on Channel Select Input Improved Linearity and Lower ON Resistance over Input Voltage Latch-up Performance Exceeds 300 mA ESD Performance: Human Body Model > 2000 V; Machine Model > 200 V Chip Complexity: 38 FETs Pb-Free Packages are Available A0AYWG G A0 MG G 1 A0 = Specific Device Code A = Assembly Location Y = Year W = Work Week M = Date Code G = Pb-Free Package (Note: Microdot may be in either location) ORDERING INFORMATION See detailed ordering and shipping information in the package dimensions section on page 9 of this data sheet. FUNCTION TABLE 1 6 NO V+ 2 5 COM GND 3 4 NC SELECT Select ON Channel L H NC NO Figure 1. Pin Assignment U U COM 2X0 2X1 U CHANNEL SELECT NO NC Figure 2. Logic Symbol *For additional information on our Pb-Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. (c) Semiconductor Components Industries, LLC, 2006 June, 2006 - Rev. 9 1 Publication Order Number: NLAS4599/D NLAS4599 ABSOLUTE MAXIMUM RATINGS Symbol Parameter Value Unit -0.5 to +7.0 V -0.5 VIS VCC )0.5 V -0.5 VI + 7.0 V $50 mA 200 200 mW -65 to +150 C Lead Temperature, 1mm from Case for 10 seconds 260 C TJ Junction Temperature Under Bias 150 C VESD ESD Withstand Voltage Human Body Model (Note 1) Machine Model (Note 2) Charged Device Model (Note 3) 2000 200 N/A V ILATCH-UP Latch-Up Performance Above VCC and Below GND at 125C (Note 4) $300 mA JA Thermal Resistance 333 333 C/W VCC Positive DC Supply Voltage VIS Analog Input Voltage (VNO or VCOM) VIN Digital Select Input Voltage IIK DC Current, Into or Out of Any Pin PD Power Dissipation in Still Air TSTG Storage Temperature Range TL SC-88 TSOP-6 SC-88 TSOP-6 Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect device reliability. 1. Tested to EIA/JESD22-A114-A 2. Tested to EIA/JESD22-A115-A 3. Tested to JESD22-C101-A 4. Tested to EIA/JESD78 RECOMMENDED OPERATING CONDITIONS Symbol Characteristics Min Max Unit 2.0 5.5 V 5.5 V VCC DC Supply Voltage VIN Digital Select Input Voltage GND VIS Analog Input Voltage (NC, NO, COM) GND VCC V TA Operating Temperature Range -55 +125 C tr, tf Input Rise or Fall Time, SELECT 0 0 100 20 ns/V 1,032,200 117.8 90 419,300 47.9 100 178,700 20.4 110 79,600 9.4 120 37,000 4.2 130 17,800 2.0 140 8,900 1.0 TJ = 80C 80 TJ = 90C Time, Years TJ = 100C Time, Hours TJ = 110C Junction Temperature 5C FAILURE RATE OF PLASTIC = CERAMIC UNTIL INTERMETALLICS OCCUR TJ = 120C DEVICE JUNCTION TEMPERATURE VERSUS TIME TO 0.1% BOND FAILURES TJ = 130C NORMALIZED FAILURE RATE VCC = 3.3 V + 0.3 V VCC = 5.0 V + 0.5 V 1 1 10 100 1000 TIME, YEARS Figure 3. Failure Rate vs. Time Junction Temperature http://onsemi.com 2 NLAS4599 DC CHARACTERISTICS - Digital Section (Voltages Referenced to GND) Guaranteed Limit Symbol Parameter Condition VCC -55 to 255C <855C <1255C Unit VIH Minimum High-Level Input Voltage, Select Input 2.0 2.5 3.0 4.5 5.5 1.5 1.9 2.1 3.15 3.85 1.5 1.9 2.1 3.15 3.85 1.5 1.9 2.1 3.15 3.85 V VIL Maximum Low-Level Input Voltage, Select Input 2.0 2.5 3.0 4.5 5.5 0.5 0.6 0.9 1.35 1.65 0.5 0.6 0.9 1.35 1.65 0.5 0.6 0.9 1.35 1.65 V IIN Maximum Input Leakage Current, Select Input VIN = 5.5 V or GND 5.5 +0.1 +1.0 +1.0 A IOFF Power Off Leakage Current VIN = 5.5 V or GND 0 $10 $10 $10 A ICC Maximum Quiescent Supply Current Select and VIS = VCC or GND 5.5 1.0 1.0 2.0 A DC ELECTRICAL CHARACTERISTICS - Analog Section Guaranteed Limit Symbol Parameter Condition VCC -55 to 255C <855C <1255C Unit RON Maximum "ON" Resistance (Figures 17 - 23) VIN = VIL or VIH VIS = GND to VCC IINI < 10.0 mA 2.5 3.0 4.5 5.5 85 45 30 25 95 50 35 30 105 55 40 35 RFLAT ON Resistance Flatness (Figures 17 - 23) VIN = VIL or VIH IINI < 10.0 mA VIS = 1V, 2V, 3.5V 4.5 4 4 5 ON Resistance Match Between Channels VIN = VIL or VIH IINI < 10.0 mA VNO or VNC = 3.5 V 4.5 2 2 3 (ON) INC(OFF) INO(OFF) NO or NC Off Leakage Current (Figure 9) VIN = VIL or VIH VNO or VNC = 1.0 VCOM 4.5 V 5.5 1 10 100 nA ICOM(ON COM ON Leakage Current (Figure 9) VIN = VIL or VIH VNO 1.0 V or 4.5 V with VNC floating or VNO 1.0 V or 4.5 V with VNO floating VCOM = 1.0 V or 4.5 V 5.5 1 10 100 nA (ON) RON ) http://onsemi.com 3 NLAS4599 AC ELECTRICAL CHARACTERISTICS (Input tr = tf = 3.0 ns) Guaranteed Max Limit Symbol Parameter VCC VIS -55 to 255C <855C <1255C Test Conditions (V) (V) Min Typ* Max Min Max Min Max Unit tON Turn-On Time (Figures 12 and 13) RL = 300 CL = 35 pF (Figures 5 and 6) 2.5 3.0 4.5 5.5 2.0 2.0 3.0 3.0 5 5 2 2 23 16 11 9 28 21 16 14 5 5 2 2 30 25 20 20 5 5 2 2 30 25 20 20 ns tOFF Turn-Off Time (Figures 12 and 13) RL = 300 CL = 35 pF (Figures 5 and 6) 2.5 3.0 4.5 5.5 2.0 2.0 3.0 3.0 1 1 1 1 7 5 4 3 12 10 9 8 1 1 1 1 15 15 12 12 1 1 1 1 15 15 12 12 ns tBBM Minimum Break-Before-Make Time VIS = 3.0 V (Figure 4) RL = 300 CL = 35 pF 2.5 3.0 4.5 5.5 2.0 2.0 3.0 3.0 1 1 1 1 12 11 6 5 1 1 1 1 1 1 1 1 ns *Typical Characteristics are at 25C. Typical @ 25, VCC = 5.0 V CIN CNO or CNC CCOM C(ON) Maximum Input Capacitance, Select Input Analog I/O (switch off) Common I/O (switch off) Feedthrough (switch on) 8 10 10 20 pF ADDITIONAL APPLICATION CHARACTERISTICS (Voltages Referenced to GND Unless Noted) Symbol Parameter Condition VCC (V) Typical 25C Unit BW Maximum On-Channel -3dB Bandwidth or Minimum Frequency Response (Figure 10) VIN = 0 dBm VIN centered between VCC and GND (Figure 7) 3.0 4.5 5.5 170 200 200 MHz VONL Maximum Feedthrough On Loss VIN = 0 dBm @ 100 kHz to 50 MHz VIN centered between VCC and GND (Figure 7) 3.0 4.5 5.5 -3 -3 -3 dB VISO Off-Channel Isolation (Figure 10) f = 100 kHz; VIS = 1 V RMS VIN centered between VCC and GND (Figure 7) 3.0 4.5 5.5 -93 -93 -93 dB Q Charge Injection Select Input to Common I/O (Figure 15) VIN = VCC to GND, FIS = 20 kHz tr = tf = 3 ns RIS = 0 , CL = 1000 pF Q = CL * VOUT (Figure 8) 3.0 5.5 1.5 3.0 pC Total Harmonic Distortion THD + Noise (Figure 14) FIS = 20 Hz to 100 kHz, RL = Rgen = 600 , CL = 50 pF VIS = 5.0 VPP sine wave 5.5 0.1 % THD http://onsemi.com 4 NLAS4599 VCC DUT VCC Input Output GND VOUT 0.1 F 300 tBMM 35 pF 90% 90% of VOH Output Switch Select Pin GND Figure 4. tBBM (Time Break-Before-Make) VCC DUT VCC 0.1 F Input Output 50% 0V VOUT Open 50% 300 VOH 35 pF 90% 90% Output VOL Input tON tOFF Figure 5. tON/tOFF VCC VCC Input DUT Output 300 50% VOUT Open 50% 0V VOH 35 pF Output 10% VOL Input tOFF Figure 6. tON/tOFF http://onsemi.com 5 10% tON NLAS4599 50 DUT Reference Transmitted Input Output 50 Generator 50 Channel switch control/s test socket is normalized. Off isolation is measured across an off channel. On loss is the bandwidth of an On switch. VISO, Bandwidth and VONL are independent of the input signal direction. VVOUT for VIN at 100 kHz IN VOUT for VIN at 100 kHz to 50 MHz VONL = On Channel Loss = 20 Log VIN VISO = Off Channel Isolation = 20 Log Bandwidth (BW) = the frequency 3 dB below VONL Figure 7. Off Channel Isolation/On Channel Loss (BW)/Crosstalk (On Channel to Off Channel)/VONL DUT VCC VIN Output Open GND CL Output Off On VIN Figure 8. Charge Injection: (Q) 100 LEAKAGE (nA) 10 1 ICOM(ON) 0.1 ICOM(OFF) 0.01 VCC = 5.0 V INO(OFF) 0.001 -55 -20 25 70 85 TEMPERATURE (C) Figure 9. Switch Leakage vs. Temperature http://onsemi.com 6 125 Off VOUT NLAS4599 0 Bandwidth (ON-RESPONSE) 0 -40 PHASE (Degree) -20 (dB) Off Isolation -60 10 20 30 VCC = 5.0 V TA = 25C -80 -100 0.01 0.1 1 10 FREQUENCY (MHz) VCC = 5.0 V TA = 25C 100 200 0.01 Figure 10. Bandwidth and Off-Channel Isolation 0.1 1 10 FREQUENCY (MHz) 100 200 Figure 11. Phase vs. Frequency 30 30 25 25 20 20 TIME (ns) TIME (ns) VCC = 4.5 V 15 tON (ns) 10 tOFF (ns) 5 0 2.5 3 3.5 4 4.5 10 tON 5 tOFF 0 -55 5 -40 25 85 125 VCC (VOLTS) Temperature (C) Figure 12. tON and tOFF vs. VCC at 255C Figure 13. tON and tOFF vs. Temp 1 3.0 VINpp = 3.0 V VCC = 3.6 V 2.5 2.0 Q (pC) THD + NOISE (%) 15 0.1 VINpp = 5.0 V VCC = 5.5 V VCC = 5 V 1.5 1.0 0.5 VCC = 3 V 0 -0.5 0.01 1 10 100 0 1 2 3 4 FREQUENCY (kHz) VCOM (V) Figure 14. Total Harmonic Distortion Plus Noise vs. Frequency Figure 15. Charge Injection vs. COM Voltage http://onsemi.com 7 5 NLAS4599 100 100 VCC = 2.0 V 10 80 RON () ICC (nA) 1 0.1 0.01 60 VCC = 2.5 V 40 VCC = 3.0 V 0.001 VCC = 3.0 V VCC = 4.0 V 20 0.0001 VCC = 5.0 V 0.00001 -40 -20 0 20 60 VCC = 5.5 V 80 100 0 0.0 120 2.0 3.0 4.0 5.0 Temperature (C) VIS (VDC) Figure 16. ICC vs. Temp, VCC = 3 V & 5 V Figure 17. RON vs. VCC, Temp = 255C 100 90 90 80 80 70 70 60 60 RON () 100 RON () 1.0 50 40 125C 30 6.0 50 40 30 25C 20 -55C 10 0 0.0 -55C 10 85C 0.5 25C 20 1.0 1.5 2.0 0 0.0 2.5 85C 125C 0.5 1.0 1.5 VIS (VDC) 2.0 2.5 3.0 VIS (VDC) Figure 18. RON vs Temp, VCC = 2.0 V Figure 19. RON vs. Temp, VCC = 2.5 V 50 30 45 25 40 20 30 RON () RON () 35 25 20 125C 10 15 0 0.0 25C 85C 10 5 15 5 25C 85C 125C -55C -55C 0.5 1.0 1.5 2.0 2.5 3.0 3.5 0 0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 VIS (VDC) VIS (VDC) Figure 21. RON vs. Temp, VCC = 4.5 V Figure 20. RON vs. Temp, VCC = 3.0 V http://onsemi.com 8 4.5 NLAS4599 25 25 125C 20 20 RON () RON () 125C 15 25C 10 -55C 85C 15 25C 10 85C 5 -55C 5 0 0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 0 0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 5.0 VIS (VDC) VIS (VDC) Figure 22. RON vs. Temp, VCC = 5.0 V Figure 23. RON vs. Temp, VCC = 5.5 V ORDERING INFORMATION Device Nomenclature Circuit Indicator Technology Device Function Suffix Package Shipping NLAS4599DFT2 NL AS DF T2 SC-88 3000 / Tape & Reel NLAS4599DFT2G NL AS DF T2G SC-88 (Pb-Free) 3000 / Tape & Reel NLAS4599DTT1 NL AS DT T1 TSOP-6 3000 / Tape & Reel NLAS4599DTT1G NL AS DT T1G TSOP-6 (Pb-Free) 3000 / Tape & Reel NLVAS4599DFT2 NL AS DF T2 SC-88 3000 / Tape & Reel NLVAS4599DFT2G NL AS DF T2G SC-88 (Pb-Free) 3000 / Tape & Reel NLVAS4599DTT1 NL AS DT T1 TSOP-6 3000 / Tape & Reel NLVAS4599DTT1G NL AS DT T1G TSOP-6 (Pb-Free) 3000 / Tape & Reel Device For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D. http://onsemi.com 9 NLAS4599 PACKAGE DIMENSIONS SC-88/SC70-6/SOT-363 CASE 419B-02 ISSUE W D NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 3. 419B-01 OBSOLETE, NEW STANDARD 419B-02. e 6 5 4 1 2 3 HE DIM A A1 A3 b C D E e L HE -E- b 6 PL 0.2 (0.008) M E M MILLIMETERS MIN NOM MAX 0.80 0.95 1.10 0.00 0.05 0.10 0.20 REF 0.10 0.21 0.30 0.10 0.14 0.25 1.80 2.00 2.20 1.15 1.25 1.35 0.65 BSC 0.10 0.20 0.30 2.00 2.10 2.20 A3 C A A1 L SOLDERING FOOTPRINT* 0.50 0.0197 0.65 0.025 0.65 0.025 0.40 0.0157 1.9 0.0748 SCALE 20:1 mm inches SC-88/SC70-6/SOT-363 *For additional information on our Pb-Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. http://onsemi.com 10 INCHES NOM MAX 0.037 0.043 0.002 0.004 0.008 REF 0.004 0.008 0.012 0.004 0.005 0.010 0.070 0.078 0.086 0.045 0.049 0.053 0.026 BSC 0.004 0.008 0.012 0.078 0.082 0.086 MIN 0.031 0.000 NLAS4599 PACKAGE DIMENSIONS TSOP-6 CASE 318G-02 ISSUE S NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. MAXIMUM LEAD THICKNESS INCLUDES LEAD FINISH THICKNESS. MINIMUM LEAD THICKNESS IS THE MINIMUM THICKNESS OF BASE MATERIAL. 4. DIMENSIONS A AND B DO NOT INCLUDE MOLD FLASH, PROTRUSIONS, OR GATE BURRS. D 6 HE 1 5 4 2 3 E b e q c A 0.05 (0.002) L A1 DIM A A1 b c D E e L HE q MIN 0.90 0.01 0.25 0.10 2.90 1.30 0.85 0.20 2.50 0 MILLIMETERS NOM MAX 1.00 1.10 0.06 0.10 0.38 0.50 0.18 0.26 3.00 3.10 1.50 1.70 0.95 1.05 0.40 0.60 2.75 3.00 10 - MIN 0.035 0.001 0.010 0.004 0.114 0.051 0.034 0.008 0.099 0 INCHES NOM 0.039 0.002 0.014 0.007 0.118 0.059 0.037 0.016 0.108 - MAX 0.043 0.004 0.020 0.010 0.122 0.067 0.041 0.024 0.118 10 SOLDERING FOOTPRINT* 2.4 0.094 1.9 0.075 0.95 0.037 0.95 0.037 0.7 0.028 1.0 0.039 SCALE 10:1 mm inches *For additional information on our Pb-Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. "Typical" parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303-675-2175 or 800-344-3860 Toll Free USA/Canada Fax: 303-675-2176 or 800-344-3867 Toll Free USA/Canada Email: orderlit@onsemi.com N. American Technical Support: 800-282-9855 Toll Free USA/Canada Europe, Middle East and Africa Technical Support: Phone: 421 33 790 2910 Japan Customer Focus Center Phone: 81-3-5773-3850 http://onsemi.com 11 ON Semiconductor Website: www.onsemi.com Order Literature: http://www.onsemi.com/orderlit For additional information, please contact your local Sales Representative NLAS4599/D