MAX186CCAP+T - Maxim Integrated - Datasheet.Directory

MAX186/MAX188

Low-Power, 8-Channel,

Serial 12-Bit ADCs

For pricing, delivery, and ordering information, please contact Maxim Direct at

1-888-629-4642, or visit Maxim Integrated’s website at www.maximintegrated.com.

EVALUATION KIT AVAILABLE

General Description

The MAX186/MAX188 are 12-bit data-acquisition sys-

tems that combine an 8-channel multiplexer, high-

bandwidth track/hold, and serial interface together with

high conversion speed and ultra-low power consump-

tion. The devices operate with a single +5V supply or

dual ±5V supplies. The analog inputs are software con-

figurable for unipolar/bipolar and single-ended/differen-

tial operation.

The 4-wire serial interface directly connects to SPI,

QSPI™ and MICROWIRE®devices without external

logic. A serial strobe output allows direct connection to

TMS320 family digital signal processors. The

MAX186/MAX188 use either the internal clock or an

external serial-interface clock to perform successive-

approximation A/D conversions. The serial interface can

operate beyond 4MHz when the internal clock is used.

The MAX186 has an internal 4.096V reference while the

MAX188 requires an external reference. Both parts have

a reference-buffer amplifier that simplifies gain trim .

The MAX186/MAX188 provide a hard-wired SHDN pin

and two software-selectable power-down modes.

Accessing the serial interface automatically powers up

the devices, and the quick turn-on time allows the

MAX186/MAX188 to be shut down between every con-

version. Using this technique of powering down

between conversions, supply current can be cut to

under 10µA at reduced sampling rates.

The MAX186/MAX188 are available in 20-pin PDIP and

SO packages, and in a shrink small-outline package

(SSOP), that occupies 30% less area than an 8-pin

PDIP. For applications that call for a parallel interface,

see the MAX180/MAX181 data sheet. For anti-aliasing

filters, consult the MAX274/MAX275 data sheet.

________________________Applications

Portable Data Logging

Data-Acquisition

High-Accuracy Process Control

Automatic Testing

Robotics

Battery-Powered Instruments

Medical Instruments

____________________________Features

o8-Channel Single-Ended or 4-Channel

Differential Inputs

oSingle +5V or ±5V Operation

oLow Power: 1.5mA (Operating Mode)

2µA (Power-Down Mode)

oInternal Track/Hold, 133kHz Sampling Rate

oInternal 4.096V Reference (MAX186)

oSPI-/QSPI-/MICROWIRE-/TMS320-Compatible

4-Wire Serial Interface

oSoftware-Configurable Unipolar or Bipolar Inputs

o20-Pin PDIP, SO, SSOP Packages

oEvaluation Kit Available

Ordering Information

TOP VIEW

PDIP/SO/SSOP

VDD

SCLK

DIN

SSTRB

DOUT

DGND

AGND

REFADJ

VREFSHDN

VSS

CH7

CH6

CH5

CH4

CH3

CH2

CH1

CH0

MAX186

MAX188

____________________Pin Configuration

QSPI is a trademark of Motorola.

MICROWIRE is a registered trademark of National

Semiconductor.

19-0123; Rev 5; 1/12

Ordering Information continued on last page.

†

Parts are offered in grades A, B, C and D (grades defined in

Electrical Characteristics). When ordering, please specify grade.

Contact factory for availability of A-grade in SSOP package.

Dice are specified at +25°C, DC parameters only.

Denotes a lead(Pb)-free/RoHS-compliant package.

PART† TEMP RANGE PIN-PACKAGE

MAX186_CPP+ 0°C to +70°C 20 PDIP

MAX186_CWP+ 0°C to +70°C 20 SO

MAX186_CAP+ 0°C to +70°C 20 SSOP

MAX186DC/D 0°C to +70°C Dice*

MAX186_EPP+ -40°C to +85°C 20 PDIP

MAX186_EWP+ -40°C to +85°C 20 SO

MAX186_EAP+ -40°C to +85°C 20 SSOP

Relative Accuracy (Note 2)

Low-Power, 8-Channel,

Serial 12-Bit ADCs

2 Maxim Integrated

MAX186/MAX188

ABSOLUTE MAXIMUM RATINGS

ELECTRICAL CHARACTERISTICS

(VDD = 5V ±5%; VSS = 0V or -5V; fCLK = 2.0MHz, external clock (50% duty cycle); 15 clocks/conversion cycle (133ksps); MAX186—

4.7µF capacitor at VREF pin; MAX188—external reference, VREF = 4.096V applied to VREF pin; TA= TMIN to TMAX, unless otherwise

noted.)

Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional

operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to

absolute maximum rating conditions for extended periods may affect device reliability.

PARAMETER SYMBOL MIN TYP MAX UNITS

±1.0

LSB

±0.75

±1.0

±0.5

Differential Nonlinearity DNL ±1 LSB

±2.0

±3.0

Resolution 12 Bits

±0.5

Offset Error

±3.0

LSB

±3.0

±1.5

±2.0

Gain Error (Note 3)

±3.0

LSB

Gain Temperature Coefficient ±0.8 ppm/°C

±0.1 LSB

SINAD 70 dB

THD -80 dB

Spurious-Free Dynamic Range SFDR 80 dB

Channel-to-Channel Crosstalk -85 dB

CONDITIONS

MAX186D/MAX188D

MAX186 (all grades)

MAX188C

MAX186C

MAX186B/MAX188B

No missing codes over temperature

MAX186A/MAX188A

MAX186B/MAX188B

MAX186C/MAX188C

External reference

4.096V (MAX188)

External reference, 4.096V

MAX186A/MAX188A

65kHz, VIN = 4.096VP-P (Note 4)

VDD to AGND............................................................-0.3V to +6V

VSS to AGND ............................................................+0.3V to -6V

VDD to VSS ..............................................................-0.3V to +12V

AGND to DGND.....................................................-0.3V to +0.3V

CH0–CH7 to AGND, DGND .............(VSS - 0.3V) to (VDD + 0.3V)

CH0–CH7 Total Input Current...........................................±20mA

VREF to AGND ...........................................-0.3V to (VDD + 0.3V)

REFADJ to AGND.......................................-0.3V to (VDD + 0.3V)

Digital Inputs to DGND...............................-0.3V to (VDD + 0.3V)

Digital Outputs to DGND............................-0.3V to (VDD + 0.3V)

Digital Output Sink Current .................................................25mA

Continuous Power Dissipation (TA = +70°C)

PDIP (derate 11.11mW/°C above +70°C).....................889mW

SO (derate 10.00mW/°C above +70°C)........................800mW

SSOP (derate 8.00mW/°C above +70°C) .....................640mW

Operating Temperature Ranges

MAX186_C/MAX188_C ........................................0°C to +70°C

MAX186_E/MAX188_E......................................-40°C to +85°C

Storage Temperature Range .............................-60°C to +150°C

Lead Temperature (soldering, 10s) .................................+300°C

Soldering Temperature (reflow) .......................................+260°C

MAX188A

MAX188B

MAX188C

MAX188D

Channel-to-Channel

Offset Matching

Signal-to-Noise + Distortion Ratio

Total Harmonic Distortion

(up to the 5th harmonic)

DC ACCURACY (Note 1)

DYNAMIC SPECIFICATIONS (10kHz sine wave input, 4.096VP-P, 133ksps, 2.0MHz external clock, bipolar input mode)

External Clock Frequency Range

Low-Power, 8-Channel,

Serial 12-Bit ADCs

Maxim Integrated 3

MAX186/MAX188

PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS

Small-Signal Bandwidth -3dB rolloff 4.5 MHz

Full-Power Bandwidth 800 kHz

Internal clock 5.5 10

Conversion Time (Note 5) t CONV External clock, 2MHz, 12 clocks/conversion 6µs

Track/Hold Acquisition Time tAZ 1.5 µs

Aperture Delay 10 ns

Aperture Jitter <50 ps

Internal Clock Frequency 1.7 MHz

ELECTRICAL CHARACTERISTICS (continued)

(VDD = 5V ±5%; VSS = 0V or -5V; fCLK = 2.0MHz, external clock (50% duty cycle); 15 clocks/conversion cycle (133ksps); MAX186—

4.7µF capacitor at VREF pin; MAX188—external reference, VREF = 4.096V applied to VREF pin; TA= TMIN to TMAX, unless otherwise

noted.)

External compensation, 4.7µF 0.1 2.0

Internal compensation (Note 6) 0.1 0.4

Used for data transfer only 10

MHz

Unipolar, VSS = 0V

Input Voltage Range,

Single-Ended and Differential

(Note 9) Bipolar, VSS = -5V

Multiplexer Leakage Current On/off leakage current, VIN = ±5V ±0.01 ±1 µA

Input Capacitance (Note 6) 16 pF

VREF Output Voltage TA= +25°C 4.076 4.096 4.116 V

VREF Short-Circuit Current 30 mA

MAX186A, MAX186B,

MAX186C

±30 ±50

±30 ±60

VREF Tempco

MAX186D ±30

Load Regulation (Note 7) 0 to 0.5mA output load 2.5

Internal compensation 0

Capacitive Bypass at VREF External compensation 4.7 µF

Internal compensation 0.01

Capacitive Bypass at REFADJ External compensation 0.01 µF

MAX186_C

MAX186_E

REFADJ Adjustment Range ±1.5 %

±VREF/2

0 to

VREF

Input Voltage Range V

Input Current 200 350 µA

Input Resistance 12 20 kΩ

Shutdown VREF Input Current 1.5 10 µA

Buffer Disable Threshold REFADJ VDD -

50mV V

VDD +

2.50 50mV

CONVERSION RATE

ANALOG INPUT

INTERNAL REFERENCE (MAX186 only, reference buffer enabled)

EXTERNAL REFERENCE AT VREF (Buffer disabled, VREF = 4.096V)

ppm/°C

Low-Power, 8-Channel,

Serial 12-Bit ADCs

4 Maxim Integrated

MAX186/MAX188

ELECTRICAL CHARACTERISTICS (continued)

(VDD = 5V ±5%; VSS = 0V or -5V; fCLK = 2.0MHz, external clock (50% duty cycle); 15 clocks/conversion cycle (133ksps); MAX186—

4.7µF capacitor at VREF pin; MAX188—external reference, VREF = 4.096V applied to VREF pin; TA= TMIN to TMAX, unless otherwise

noted.)

PARAMETER SYMBOL CONDITIONS MIN TYP MAX

Internal compensation mode 0µFCapacitive Bypass at VREF External compensation mode 4.7

MAX186 1.678 V/V

MAX188 1.638

MAX186 ±50 µAREFADJ Input Current MAX188 ±5

VINH 2.4 V

VINL 0.8 V

DIN, SCLK, CS Input Hysteresis VHYST 0.15 V

DIN, SCLK, CS Input Leakage IIN VIN = 0V or VDD ±1 µA

CIN (Note 6) 15 pF

SHDN Input High Voltage VINH VDD - 0.5 V

SHDN Input Low Voltage VINL 0.5 V

SHDN Input Current, High IINH VSHDN = VDD 4.0 µA

SHDN Input Current, Low IINL VSHDN = 0V -4.0 µA

SHDN Input Mid Voltage VIM V

SHDN Voltage, Open VFLT VSHDN = open 2.75 V

VSHDN = open -100 100 nA

ISINK = 5mA 0.4

Output Voltage Low VOL ISINK = 16mA 0.3 V

Output Voltage High VOH ISOURCE = 1mA 4 V

Three-State Leakage Current ILVCS = 5V ±10 µA

Three-State Output Capacitance COUT VCS = 5V (Note 6) 15 pF

Positive Supply Voltage VDD 5 ±5% V

DIN, SCLK, CS Input Capacitance

SHDN Max Allowed Leakage,

Mid Input

Negative Supply Voltage VSS 0 or

-5 ±5% V

Operating mode 1.5 2.5

Fast power-down 30 70

Positive Supply Current IDD

Full power-down 210

Operating mode and fast power-down 50

Negative Supply Current ISS Full power-down 10 µA

µA

DIN, SCLK, CS Input Low Voltage

DIN, SCLK, CS Input High Voltage

1.5 VDD -1.5

DIGITAL INPUTS (DIN, SCLK, CCSS, SSHHDDNN)

DIGITAL OUTPUTS (DOUT, SSTRB)

POWER REQUIREMENTS

UNITS

EXTERNAL REFERENCE AT REFADJ

Reference-Buffer Gain

CLOAD = 100pF 20 150SCLK Fall to Output Data Valid tDO MAX18_ _C/E

Note 1: Tested at VDD = 5.0V; VSS = 0V; unipolar input mode.

Note 2: Relative accuracy is the deviation of the analog value at any code from its theoretical value after the full-scale range has

been calibrated.

Note 3: MAX186 – internal reference, offset nulled; MAX188 – external reference (VREF = +4.096V), offset nulled.

Note 4: Ground on-channel; sine wave applied to all off channels.

Note 5: Conversion time defined as the number of clock cycles times the clock period; clock has 50% duty cycle.

Note 6: Guaranteed by design. Not subject to production testing.

Note 7: External load should not change during conversion for specified accuracy.

Note 8: Measured at VSUPPLY +5% and VSUPPLY -5% only.

Note 9: The common-mode range for the analog inputs is from VSS to VDD.

Low-Power, 8-Channel,

Serial 12-Bit ADCs

Maxim Integrated 5

MAX186/MAX188

PARAMETER SYMBOL CONDITIONS UNITS

Positive Supply Rejection

(Note 8) PSR ±0.06 ±0.5 mV

Negative Supply Rejection

(Note 8) PSR VSS = -5V ±5%; external reference, 4.096V;

full-scale input ±0.01 ±0.5 mV

ELECTRICAL CHARACTERISTICS (continued)

(VDD = 5V ±5%; VSS = 0V or -5V; fCLK = 2.0MHz, external clock (50% duty cycle); 15 clocks/conversion cycle (133ksps); MAX186—

4.7µF capacitor at VREF pin; MAX188—external reference, VREF = 4.096V applied to VREF pin; TA= TMIN to TMAX, unless otherwise

noted.)

TIMING CHARACTERISTICS

(VDD = 5V ±5%; VSS =0V or -5V, TA= TMIN to TMAX, unless otherwise noted.)

PARAMETER SYMBOL CONDITIONS UNITS

SCLK Pulse Width Low tCL 200 ns

SCLK Fall to SSTRB tSSTRB CLOAD = 100pF 200 ns

tSDV External clock mode only, CLOAD = 100pF 200 ns

tSTR External clock mode only, CLOAD = 100pF 200 ns

tSCK Internal clock mode only 0ns

Acquisition Time tAZ 1.5 µs

DIN to SCLK Setup tDS 100 ns

DIN to SCLK Hold tDH 0ns

CS Fall to Output Enable tDV CLOAD = 100pF 100 ns

CS Rise to Output Disable tTR CLOAD = 100pF 100 ns

CS to SCLK Rise Setup tCSS 100 ns

CS to SCLK Rise Hold tCSH 0ns

SCLK Pulse Width High tCH 200 ns

SSTRB Rise to SCLK Rise

(Note 6)

CS Fall to SSTRB Output Enable

(Note 6)

VDD = 5V ±5%; external reference, 4.096V;

full-scale input

MIN TYP MAX

CS Rise to SSTRB Output Disable

(Note 6)

Low-Power, 8-Channel,

Serial 12-Bit ADCs

6 Maxim Integrated

MAX186/MAX188

Low-Power, 8-Channel,

Serial 12-Bit ADCs

__________________________________________Typical Operating Characteristics

0.30

-0.05

-60 140

POWER-SUPPLY REJECTION

vs. TEMPERATURE

0.00

0.25

TEMPERATURE (°C)

PSR (LSBs)

0.10

0.05

-40 20 100

0.15

0.20

-20 0 40 80 120

VDD = +5V ±5%

VSS = 0V or -5V

2.456

INTERNAL REFERENCE VOLTAGE

vs. TEMPERATURE

2.452

2.455

TEMPERATURE (°C)

VREFADJ (V)

2.454

2.453

-40 -20 0 20 40 60 80 100 120

0.16

-60 -20 60 140

CHANNEL-TO-CHANNEL OFFSET MATCHING

vs. TEMPERATURE

0.02

0.12

TEMPERATURE (°C)

OFFSET MATCHING (LSBs)

20 100

0.10

0.04

-40 0 40 80 120

0.14

0.08

0.06

-140

066.5kHz

MAX186/MAX188 FFT PLOT – 133kHz

-120

-80

-100

-40

-20

-60

ft = 10kHz

fs = 133kHz

33.25kHz

AMPLITUDE (dB)

FREQUENCY

ft = 10kHz

fs = 133kHz

TA = +25°C

_____________________________________________________________Pin Description

PIN NAME FUNCTION

1–8 CH0–CH7 Sampling Analog Inputs

9 VSS Negative Supply Voltage. Connect to -5V ±5% or AGND

10 SHDN

Three-Level Shutdown Input. Pulling SHDN low shuts the MAX186/MAX188 down to 10μA (max)

supply current, otherwise the MAX186/MAX188 are fully operational. Pulling SHDN high puts the

reference-buffer amplifier in internal compensation mode. Leaving SHDN unconnected puts the

reference-buffer amplifier in external compensation mode.

11 VREF

Reference Voltage for analog-to-digital conversion. Also, output of the reference buffer amplifier

(4.096V in the MAX186, 1.638 x REFADJ in the MAX188). Add a 4.7μF capacitor to ground when

using external compensation mode. Also functions as an input when used with a precision external

Low-Power, 8-Channel,

Serial 12-Bit ADCs

Maxim Integrated 7

MAX186/MAX188

+5V

3kΩ

CLOAD

DGND

DOUT

CLOAD

DGND

3kΩ

DOUT

a. High-Z to VOH and VOL to VOH b. High-Z to VOL and VOH to VOL

+5V

3kΩ

CLOAD

DGND

DOUT

CLOAD

DGND

3kΩ

DOUT

a VOH to High-Z b VOL to High-Z

Figure 1. Load Circuits for Enable Time

Figure 2. Load Circuits for Disabled Time

INPUT

SHIFT

LOGIC

INT

CLOCK

OUTPUT

SHIFT

+2.46V

REFERENCE

(MAX186)

T/H

ANALOG

INPUT

MUX

12-BIT

SAR

ADC

DOUT

SSTRB

VDD

DGND

VSS

SCLK

DIN

CH0

CH1

CH3

CH2

CH7

CH6

CH5

CH4

AGND

REFADJ

VREF

OUT

REF

CLOCK

+4.096V

20kΩ

≈ 1.65

MAX186

MAX188

SHDN

Figure 3. Block Diagram

________________________________________________Pin Description (continued)

PIN NAME FUNCTION

12 REFADJ

Input to the Reference-Buffer Amplifier. To disable the reference-buffer amplifier, connect REFADJ to

VDD.

13 AGND Analog Ground. Also IN- Input for single-ended conversions.

14 DGND Digital Ground

15 DOUT Serial Data Output. Data is clocked out at the falling edge of SCLK. High impedance when CS is high.

16 SSTRB

Serial Strobe Output. In internal clock mode, SSTRB goes low when the MAX186/MAX188 begin the

A/D conversion and goes high when the conversion is done. In external clock mode, SSTRB pulses

high for one clock period before the MSB decision. High impedance when CS is high (external mode).

17 DIN Serial Data Input. Data is clocked in at the rising edge of SCLK.

18 CS

Active-Low Chip Select. Data will not be clocked into DIN unless CS is low. When CS is high, DOUT

is high impedance.

19 SCLK

Serial Clock Input. Clocks data in and out of serial interface. In external clock mode, SCLK also sets

the conversion speed. (Duty cycle must be 40% to 60% in external clock mode.)

20 VDD Positive Supply Voltage, +5V ±5%

_______________Detailed Description

The MAX186/MAX188 use a successive-approximation

conversion technique and input track/hold (T/H) circuit-

ry to convert an analog signal to a 12-bit digital output.

A flexible serial interface provides easy interface to

microprocessors. No external hold capacitors are

required. Figure 3 shows the block diagram for the

MAX186/MAX188.

Pseudo-Differential Input

The sampling architecture of the ADC’s analog com-

parator is illustrated in the Equivalent Input Circuit

(Figure 4). In single-ended mode, IN+ is internally

switched to CH0-CH7 and IN- is switched to AGND. In

differential mode, IN+ and IN- are selected from pairs

of CH0/CH1, CH2/CH3, CH4/CH5 and CH6/CH7.

Configure the channels with Table 3 and Table 4.

In differential mode, IN- and IN+ are internally switched

to either one of the analog inputs. This configuration is

pseudo-differential to the effect that only the signal at

IN+ is sampled. The return side (IN-) must remain sta-

ble within ±0.5LSB (±0.1LSB for best results) with

respect to AGND during a conversion. Accomplish this

by connecting a 0.1µF capacitor from AIN- (the select-

ed analog input, respectively) to AGND.

During the acquisition interval, the channel selected as

the positive input (IN+) charges capacitor CHOLD. The

acquisition interval spans three SCLK cycles and ends

on the falling SCLK edge after the last bit of the input

control word has been entered. At the end of the acqui-

sition interval, the T/H switch opens, retaining charge

on CHOLD as a sample of the signal at IN+.

The conversion interval begins with the input multiplex-

er switching CHOLD from the positive input (IN+) to the

negative input (IN-). In single-ended mode, IN- is sim-

ply AGND. This unbalances node ZERO at the input of

the comparator. The capacitive DAC adjusts during the

remainder of the conversion cycle to restore node

ZERO to 0V within the limits of 12-bit resolution. This

action is equivalent to transferring a charge of 16pF x

[(VIN+) - (VIN-)] from CHOLD to the binary-weighted

capacitive DAC, which in turn forms a digital represen-

tation of the analog input signal.

Track/Hold

The T/H enters its tracking mode on the falling clock

edge after the fifth bit of the 8-bit control word has been

shifted in. The T/H enters its hold mode on the falling

clock edge after the eighth bit of the control word has

been shifted in. If the converter is set up for

single-ended inputs, IN- is connected to AGND, and

the converter samples the “+” input. If the converter is

set up for differential inputs, IN- connects to the “-”

input, and the difference of |IN+ - IN-|is sampled. At

the end of the conversion, the positive input connects

back to IN+, and CHOLD charges to the input signal.

The time required for the T/H to acquire an input signal

is a function of how quickly its input capacitance is

charged. If the input signal’s source impedance is high,

the acquisition time lengthens and more time must be

allowed between conversions. Acquisition time is cal-

culated by:

tAZ = 9 x (RS+ RIN) x 16pF,

where RIN = 5kΩ, RS= the source impedance of the

input signal, and tAZ is never less than 1.5µs. Note that

source impedances below 5kΩdo not significantly

affect the AC performance of the ADC. Higher source

impedances can be used if an input capacitor is con-

nected to the analog inputs, as shown in Figure 5. Note

that the input capacitor forms an RC filter with the input

source impedance, limiting the ADC’s signal bandwidth.

Input Bandwidth

The ADC’s input tracking circuitry has a 4.5MHz

small-signal bandwidth, so it is possible to digitize

high-speed transient events and measure periodic sig-

nals with bandwidths exceeding the ADC’s sampling

rate by using undersampling techniques. To avoid

high-frequency signals being aliased into the frequency

band of interest, anti-alias filtering is recommended.

Low-Power, 8-Channel,

Serial 12-Bit ADCs

8 Maxim Integrated

MAX186/MAX188

CH0

CH1

CH2

CH3

CH4

CH5

CH6

CH7

AGND

CSWITCH

TRACK

T/H

SWITCH

10kΩ

CHOLD

HOLD

12-BIT CAPACITIVE DAC

VREF

ZERO

COMPARATOR

–+

16pF

SINGLE-ENDED MODE: IN+ = CHO-CH7, IN– = AGND.

DIFFERENTIAL MODE: IN+ AND IN– SELECTED FROM PAIRS OF

CH0/CH1, CH2/CH3, CH4/CH5, CH6/CH7.

AT THE SAMPLING INSTANT,

THE MUX INPUT SWITCHES

FROM THE SELECTED IN+

CHANNEL TO THE SELECTED

IN– CHANNEL.

INPUT

MUX

Figure 4. Equivalent Input Circuit

Full Scale

VREFADJ x A*

Analog Input Range and Input Protection

Internal protection diodes, which clamp the analog

input to VDD and VSS, allow the channel input pins to

swing from VSS - 0.3V to VDD + 0.3V without damage.

However, for accurate conversions near full scale, the

inputs must not exceed VDD by more than 50mV, or be

lower than VSS by 50mV.

If the analog input exceeds 50mV beyond the sup-

plies, do not forward bias the protection diodes of

off-channels over two milliamperes, as excessive

current will degrade the conversion accuracy of the

on-channel.

The full-scale input voltage depends on the voltage at

VREF. See Tables 1a and 1b.

Quick Look

To evaluate the analog performance of the

MAX186/MAX188 quickly, use the circuit of Figure 5.

The MAX186/MAX188 require a control byte to be writ-

ten to DIN before each conversion. Tying DIN to +5V

feeds in control bytes of $FF (HEX), which trigger

Low-Power, 8-Channel,

Serial 12-Bit ADCs

Maxim Integrated 9

MAX186/MAX188

Reference Zero

Scale Full Scale

Internal Reference

(MAX186 only) 0V +4.096V

at VREF 0V VREF

External Reference

at REFADJ

Reference Negative

Full Scale

Zero

Scale

Internal Reference

(MAX186 only) -4.096V/2 0V

External Reference

at REFADJ

-1/2VREFADJ

x A* 0V

at VREF -1/2 VREF 0V

+4.096V/2

+1/2VREFADJ

x A*

+1/2 VREF

0.1µF

VDD

DGND

AGND

VSS

SCLK

DIN

DOUT

SSTRB

SHDN

+5V

N.C.

0.01µF

CH7

REFADJ

VREF

0.01µF

+2.5V

REFERENCE

4.7µF

1N4148

+5V

0V TO

4.096V

ANALOG

INPUT

+2.5V **

OSCILLOSCOPE

CH1 CH2 CH3 CH4

* FULL-SCALE ANALOG INPUT, CONVERSION RESULT = $FFF (HEX)

**REQUIRED FOR MAX188 ONLY. A POTENTIOMETER MAY BE USED IN PLACE OF THE REFERENCE FOR TEST PURPOSES.

MAX186

MAX188

+5V

2MHz

OSCILLATOR

SCLK

SSTRB

DOUT*

Figure 5. Quick-Look Circuit

* A = 1.678 for the MAX186, 1.638 for the MAX188

Table 1b. Bipolar Full Scale, Zero Scale, and

Negative Full Scale

Table 1a. Unipolar Full Scale and Zero Scale

* A = 1.678 for the MAX186, 1.638 for the MAX188

single-ended unipolar conversions on CH7 in external

clock mode without powering down between conver-

sions. In external clock mode, the SSTRB output pulses

high for one clock period before the most significant bit

of the 12-bit conversion result comes out of DOUT.

Varying the analog input to CH7 should alter the

sequence of bits from DOUT. A total of 15 clock cycles

is required per conversion. All transitions of the SSTRB

and DOUT outputs occur on the falling edge of SCLK.

How to Start a Conversion

A conversion is started on the MAX186/MAX188 by

clocking a control byte into DIN. Each rising edge on

SCLK, with CS low, clocks a bit from DIN into the

MAX186/MAX188’s internal shift register. After CS falls,

the first arriving logic “1” bit defines the MSB of the

control byte. Until this first “start” bit arrives, any num-

ber of logic “0” bits can be clocked into DIN with no

effect. Table 2 shows the control-byte format.

The MAX186/MAX188 are fully compatible with

Microwire and SPI devices. For SPI, select the correct

clock polarity and sampling edge in the SPI control reg-

isters: set CPOL = 0 and CPHA = 0. Microwire and SPI

both transmit a byte and receive a byte at the same

time. Using the

Typical Operating Circuit

, the simplest

software interface requires only three 8-bit transfers to

perform a conversion (one 8-bit transfer to configure

the ADC, and two more 8-bit transfers to clock out the

12-bit conversion result).

Example: Simple Software Interface

Make sure the CPU’s serial interface runs in master

mode so the CPU generates the serial clock. Choose a

clock frequency from 100kHz to 2MHz.

1) Set up the control byte for external clock mode, call

it TB1. TB1 should be of the format: 1XXXXX11

Binary, where the Xs denote the particular channel

and conversion-mode selected.

Low-Power, 8-Channel,

Serial 12-Bit ADCs

10 Maxim Integrated

MAX186/MAX188

Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0

(MSB) (LSB)

START SEL2 SEL1 SEL0 UNI/BIP SGL/DIF PD1 PD0

Bit Name Description

7(MSB) START The first logic “1” bit after CS goes low defines the beginning of the control byte.

6 SEL2 These three bits select which of the eight channels are used for the conversion.

5 SEL1 See Tables 3 and 4.

4 SEL0

3 UNI/BIP 1= unipolar, 0= bipolar. Selects unipolar or bipolar conversion mode. In unipolar

mode, an analog input signal from 0V to VREF can be converted; in bipolar mode, the

signal can range from -VREF/2 to +VREF/2.

2 SGL/DIF 1= single ended, 0= differential. Selects single-ended or differential conversions. In

single-ended mode, input signal voltages are referred to AGND. In differential mode,

the voltage difference between two channels is measured. See Tables 3 and 4.

1 PD1 Selects clock and power-down modes.

0(LSB) PD0 PD1 PD0 Mode

00Full power-down (IQ= 2µA)

01Fast power-down (IQ= 30µA)

10Internal clock mode

1 1 External clock mode

Table 2. Control-Byte Format

2) Use a general-purpose I/O line on the CPU to pull

CS on the MAX186/MAX188 low.

3) Transmit TB1 and simultaneously receive a byte

and call it RB1. Ignore RB1.

4) Transmit a byte of all zeros ($00 HEX) and simulta-

neously receive byte RB2.

5) Transmit a byte of all zeros ($00 HEX) and simulta-

neously receive byte RB3.

6) Pull CS on the MAX186/MAX188 high.

Figure 6 shows the timing for this sequence. Bytes RB2

and RB3 will contain the result of the conversion

padded with one leading zero and three trailing zeros.

The total conversion time is a function of the serial

clock frequency and the amount of dead time between

8-bit transfers. Make sure that the total conversion time

does not exceed 120µs, to avoid excessive T/H droop.

Digital Output

In unipolar input mode, the output is straight binary

(see Figure 15). For bipolar inputs, the output is

twos-complement (see Figure 16). Data is clocked out

at the falling edge of SCLK in MSB-first format.

Low-Power, 8-Channel,

Serial 12-Bit ADCs

Maxim Integrated 11

MAX186/MAX188

SEL2 SEL1 SEL0 CH0 CH1 CH2 CH3 CH4 CH5 CH6 CH7 AGND

00 0 + –

10 0 + –

00 1 + –

10 1 + –

01 0 + –

11 0 + –

01 1 + –

11 1 + –

Table 3. Channel Selection in Single-Ended Mode (SGL/DDIIFFFF= 1)

SEL2 SEL1 SEL0 CH0 CH1 CH2 CH3 CH4 CH5 CH6 CH7

00 0 + –

00 1 + –

01 0 + –

01 1 +–

10 0 – +

10 1 – +

11 0 – +

11 1 –+

Table 4. Channel Selection in Differential Mode (SGL/DDIIFFFF= 0)

Internal and External Clock Modes

The MAX186/MAX188 may use either an external serial

clock or the internal clock to perform the

successive-approximation conversion. In both clock

modes, the external clock shifts data in and out of the

MAX186/MAX188. The T/H acquires the input signal as

the last three bits of the control byte are clocked into

DIN. Bits PD1 and PD0 of the control byte program the

clock mode. Figures 7 through 10 show the timing

characteristics common to both modes.

External Clock

In external clock mode, the external clock not only shifts

data in and out, it also drives the analog-to-digital con-

version steps. SSTRB pulses high for one clock period

after the last bit of the control byte. Successive-approxi-

mation bit decisions are made and appear at DOUT on

each of the next 12 SCLK falling edges (see Figure 6).

SSTRB and DOUT go into a high-impedance state when

CS goes high; after the next CS falling edge, SSTRB will

output a logic low. Figure 8 shows the SSTRB timing in

external clock mode.

The conversion must complete in some minimum time, or

else droop on the sample-and-hold capacitors may

degrade conversion results. Use internal clock mode if the

clock period exceeds 10µs, or if serial-clock interruptions

could cause the conversion interval to exceed 120µs.

Low-Power, 8-Channel,

Serial 12-Bit ADCs

12 Maxim Integrated

MAX186/MAX188

SSTRB

SCLK

DIN

DOUT

14 8 12 16 20 24

START

SEL2 SEL1 SEL0 UNI/

BIP SCL/

DIFF PD1 PD0

B11

MSB B10 B9 B8 B7 B6 B5 B4 B3 B2 B1 B0

LSB

ACQUISITION

1.5μs (CLK = 2MHz)

IDLE

FILLED WITH

ZEROS

IDLE

CONVERSION

tACQ

A/D STATE

RB1

RB2 RB3

• • •

SCLK

DIN

DOUT

tCSH

tCSS tCL

tDS

tDH

tDV

tCH

tDO tTR

tCSH

Figure 6. 24-Bit External Clock Mode Conversion Timing (SPI, QSPI and Microwire Compatible)

Figure 7. Detailed Serial-Interface Timing

Internal Clock

In internal clock mode, the MAX186/MAX188 generate

their own conversion clock internally. This frees the

microprocessor from the burden of running the SAR con-

version clock, and allows the conversion results to be

read back at the processor’s convenience, at any clock

rate from zero to typically 10MHz. SSTRB goes low at the

start of the conversion and then goes high when the con-

version is complete. SSTRB will be low for a maximum of

10µs, during which time SCLK should remain low for best

noise performance. An internal register stores data when

the conversion is in progress. SCLK clocks the data out

at this register at any time after the conversion is com-

plete. After SSTRB goes high, the next falling clock edge

will produce the MSB of the conversion at DOUT, fol-

lowed by the remaining bits in MSB-first format (see

Figure 9). CS does not need to be held low once a con-

version is started. Pulling CS high prevents data from

being clocked into the MAX186/MAX188 and three-

states DOUT, but it does not adversely effect an internal

clock-mode conversion already in progress. When inter-

nal clock mode is selected, SSTRB does not go into a

high-impedance state when CS goes high.

Figure 10 shows the SSTRB timing in internal clock

mode. In internal clock mode, data can be shifted in and

out of the MAX186/MAX188 at clock rates exceeding

4.0MHz, provided that the minimum acquisition time, tAZ,

is kept above 1.5µs.

Low-Power, 8-Channel,

Serial 12-Bit ADCs

Maxim Integrated 13

MAX186/MAX188

• • •

• • • • • •

• • •

tSDV

tSSTRB

PD0 CLOCKED IN

tSTR

SSTRB

SCLK

tSSTRB

• • • • • • • •

SSTRB

SCLK

DIN

DOUT

14 8 12 18 20 24

START

SEL2 SEL1 SEL0 UNI/

DIP SCL/

DIFF PD1 PD0

B11

MSB B10 B9 B2 B1 B0

LSB

ACQUISITION

1.5μs (CLK = 2MHz)

IDLE

FILLED WITH

ZEROS

IDLE

CONVERSION

10μs MAX

A/D STATE

2 3 5 6 7 9 10 11 19 21 22 23

tCONV

Figure 8. External Clock Mode SSTRB Detailed Timing

Figure 9. Internal Clock Mode Timing

Data Framing

The falling edge of CS does not start a conversion on the

MAX186/MAX188. The first logic high clocked into DIN is

interpreted as a start bit and defines the first bit of the

control byte. A conversion starts on the falling edge of

SCLK, after the eighth bit of the control byte (the PD0 bit)

is clocked into DIN. The start bit is defined as:

The first high bit clocked into DIN with CS low any-

time the converter is idle, e.g. after VCC is applied.

The first high bit clocked into DIN after bit 5 of a

conversion in progress is clocked onto the DOUT pin.

If a falling edge on CS forces a start bit before bit 5

(B5) becomes available, then the current conversion

will be terminated and a new one started. Thus, the

fastest the MAX186/MAX188 can run is 15 clocks per

conversion. Figure 11a shows the serial-interface timing

necessary to perform a conversion every 15 SCLK

cycles in external clock mode. If CS is low and SCLK is

continuous, guarantee a start bit by first clocking in 16

zeros.

Most microcontrollers require that conversions occur in

multiples of 8 SCLK clocks; 16 clocks per conversion

will typically be the fastest that a microcontroller can

drive the MAX186/MAX188. Figure 11b shows the

serial-interface timing necessary to perform a conver-

sion every 16 SCLK cycles in external clock mode.

__________ Applications Information

Power-On Reset

When power is first applied and if SHDN is not pulled

low, internal power-on reset circuitry will activate the

MAX186/MAX188 in internal clock mode, ready to con-

vert with SSTRB = high. After the power supplies have

been stabilized, the internal reset time is 100µs and no

conversions should be performed during this phase.

SSTRB is high on power-up and, if CS is low, the first

logical 1 on DIN will be interpreted as a start bit. Until a

conversion takes place, DOUT will shift out zeros.

Reference-Buffer Compensation

In addition to its shutdown function, the SHDN pin also

selects internal or external compensation. The compen-

sation affects both power-up time and maximum conver-

sion speed. Compensated or not, the minimum clock

rate is 100kHz due to droop on the sample-and-hold.

To select external compensation, open SHDN. See the

Typical Operating Circuit

, which uses a 4.7µF capacitor at

VREF. A value of 4.7µF or greater ensures stability and

allows operation of the converter at the full clock speed of

2MHz. External compensation increases power-up time (see

the

Choosing Power-Down Mode

section, and Table 5).

Internal compensation requires no external capacitor at

VREF, and is selected by pulling SHDN high. Internal com-

pensation allows for shortest power-up times, but is only

available using an external clock and reduces the maxi-

mum clock rate to 400kHz.

Low-Power, 8-Channel,

Serial 12-Bit ADCs

14 Maxim Integrated

MAX186/MAX188

PD0 CLOCK IN

tSSTRB

tCSH

tCONV

tSCK

SSTRB • • •

SCLK • • •

tCSS

NOTE: FOR BEST NOISE PERFORMANCE, KEEP SCLK LOW DURING CONVERSION.

CS • • •

Figure 10. Internal Clock Mode SSTRB Detailed Timing

Power-Down

Choosing Power-Down Mode

You can save power by placing the converter in a

low-current shutdown state between conversions.

Select full power-down or fast power-down mode via

bits 7 and 8 of the DIN control byte with SHDN high or

open (see Tables 2 and 6). Pull SHDN low at any time to

shut down the converter completely. SHDN overrides

bits 7 and 8 of DIN word (see Table 7).

Full power-down mode turns off all chip functions that draw

quiescent current, reducing IDD and ISS typically to 2µA.

Fast power-down mode turns off all circuitry except the

bandgap reference. With the fast power-down mode, the

supply current is 30µA. Power-up time can be shortened

to 5µs in internal compensation mode.

In both software shutdown modes, the serial interface

remains operational, however, the ADC will not convert.

Table 5 illustrates how the choice of reference-buffer

compensation and power-down mode affects both

power-up delay and maximum sample rate.

In external compensation mode, the power-up time is

20ms with a 4.7µF compensation capacitor (200ms with

a 33µF capacitor) when the capacitor is fully discharged.

In fast power-down, you can eliminate start-up time by

using low-leakage capacitors that will not discharge

more than 1/2LSB while shut down. In shutdown, the

capacitor has to supply the current into the reference

(1.5µA typ) and the transient currents at power-up.

Figures 12a and 12b illustrate the various power-down

sequences in both external and internal clock modes.

Software Power-Down

Software power-down is activated using bits PD1 and

PD0 of the control byte. As shown in Table 6, PD1 and

PD0 also specify the clock mode. When software shut-

down is asserted, the ADC will continue to operate in

the last specified clock mode until the conversion is

complete. Then the ADC powers down into a low quies-

cent-current state. In internal clock mode, the interface

remains active and conversion results may be clocked

out while the MAX186/MAX188 have already entered a

software power-down.

The first logical 1 on DIN will be interpreted as a start

bit, and powers up the MAX186/MAX188. Following the

start bit, the data input word or control byte also deter-

mines clock and power-down modes. For example, if

the DIN word contains PD1 = 1, then the chip will

remain powered up. If PD1 = 0, a power-down will

resume after one conversion.

Low-Power, 8-Channel,

Serial 12-Bit ADCs

Maxim Integrated 15

MAX186/MAX188

SCLK

DIN

DOUT

S CONTROL BYTE 0 CONTROL BYTE 1S

CONVERSION RESULT 0

B11 B10 B9 B8 B7 B6 B5 B4 B3 B2 B1 B0

CONVERSION RESULT 1

SSTRB

B11 B10 B9 B8 B7 B6 B5 B4 B3 B2 B1 B0

CONTROL BYTE 2S

18181

SCLK

DIN

DOUT

S CONTROL BYTE 0 CONTROL BYTE 1S

CONVERSION RESULT 0

B11 B10 B9 B8 B7 B6 B5 B4 B3 B2 B1 B0 B11 B10 B9 B8

CONVERSION RESULT 1

• • •

Figure 11a. External Clock Mode, 15 Clocks/Conversion Timing

Figure 11b. External Clock Mode, 16 Clocks/Conversion Timing

Low-Power, 8-Channel,

Serial 12-Bit ADCs

16 Maxim Integrated

MAX186/MAX188

Reference Reference- VREF Power- Power-Up Maximum

Buffer Buffer Capacitor Down Delay Sampling

Compensation (μF) Mode (s) Rate (ksps)

Mode

Enabled Internal Fast 5µ 26

Enabled Internal Full 300µ 26

Enabled External 4.7 Fast See Figure 14c 133

Enabled External 4.7 Full See Figure 14c 133

Disabled Fast 2µ 133

Disabled Full 2µ 133

Table 5. Typical Power-Up Delay Times

PD1 PD0 Device Mode

1 1 External Clock Mode

1 0 Internal Clock Mode

0 1 Fast Power-Down Mode

0 0 Full Power-Down Mode

SSHHDDNNDevice Reference-Buffer

State Mode Compensation

1 Enabled Internal Compensation

Open Enabled External Compensation

0 Full Power-Down N/A

Table 6. Software Shutdown and Clock Mode Table 7. Hard-Wired Shutdown and

Compensation Mode

POWERED UP

FULL

POWER

DOWN

POWERED

POWERED UP

DATA VALID

(12 DATA BITS)

DATA VALID

(12 DATA BITS)

DATA INVALID

VALID

EXTERNAL

INTERNAL

SXXXXX11 S 01

XXXXX XX XXX

S11

FAST

POWER-DOWN

MODE

DOUT

DIN

CLOCK

MODE

SHDN

SETS EXTERNAL

CLOCK MODE

SETS EXTERNAL

CLOCK MODE

SETS FAST

POWER-DOWN

MODE

Figure 12a. Timing Diagram Power-Down Modes, External Clock

Low-Power, 8-Channel,

Serial 12-Bit ADCs

Maxim Integrated 17

MAX186/MAX188

FULL

POWER-DOWN POWERED

POWERED UP

DATA VALID DATA VALID

INTERNAL CLOCK MODE

SXXXXX10 S 00

XXXXX S

MODE

DOUT

DIN

CLOCK

MODE SETS INTERNAL

CLOCK MODE

SETS FULL

POWER-DOWN

CONVERSION

SSTRB

100

DIN

REFADJ

VREF

2.5V

101 1 11100 101

FULLPD FASTPD NOPD FULLPD FASTPD

2ms WAIT

COMPLETE CONVERSION SEQUENCE

tBUFFEN ≈ 15µs

τ = RC = 20kΩ x CREFADJ

(ZEROS) CH1 CH7 (ZEROS)

Hardware Power-Down

The SHDN pin places the converter into the full

power-down mode. Unlike with the software shut-down

modes, conversion is not completed. It stops coinci-

dentally with SHDN being brought low. There is no

power-up delay if an external reference is used and is

not shut down. The SHDN pin also selects internal or

external reference compensation (see Table 7).

Power-Down Sequencing

The MAX186/MAX188 auto power-down modes can

save considerable power when operating at less than

maximum sample rates. The following discussion illus-

trates the various power-down sequences.

Lowest Power at up to 500

Conversions/Channel/Second

The following examples illustrate two different power-down

sequences. Other combinations of clock rates, compen-

sation modes, and power-down modes may give lowest

power consumption in other applications.

Figure 14a depicts the MAX186 power consumption for

one or eight channel conversions utilizing full

power-down mode and internal reference compensation.

A 0.01µF bypass capacitor at REFADJ forms an RC filter

with the internal 20kΩreference resistor with a 0.2ms

time constant. To achieve full 12-bit accuracy, 10 time

constants or 2ms are required after power-up. Waiting

2ms in FASTPD mode instead of full power-up will reduce

the power consumption by a factor of 10 or more. This is

achieved by using the sequence shown in Figure 13.

Figure 12b. Timing Diagram Power-Down Modes, Internal Clock

Figure 13. MAX186 FULLPD/FASTPD Power-Up Sequence

Lowest Power at Higher Throughputs

Figure 14b shows the power consumption with

external-reference compensation in fast power-down,

with one and eight channels converted. The external

4.7µF compensation requires a 50µs wait after power-up,

accomplished by 75 idle clocks after a dummy conver-

sion. This circuit combines fast multi-channel conversion

with lowest power consumption possible. Full

power-down mode may provide increased power sav-

ings in applications where the MAX186/MAX188 are

inactive for long periods of time, but where intermittent

bursts of high-speed conversions are required.

External and Internal References

The MAX186 can be used with an internal or external

reference, whereas an external reference is required for

the MAX188. Diode D1 shown in the

Typical Operating

Circuit

ensures correct start-up. Any standard signal

diode can be used. For both parts, an external refer-

ence can either be connected directly at the VREF ter-

minal or at the REFADJ pin.

An internal buffer is designed to provide 4.096V at

VREF for both the MAX186 and MAX188. The

MAX186’s internally trimmed 2.46V reference is

buffered with a gain of 1.678. The MAX188's buffer is

trimmed with a buffer gain of 1.638 to scale an external

2.5V reference at REFADJ to 4.096V at VREF.

MAX186 Internal Reference

The full-scale range of the MAX186 with internal reference

is 4.096V with unipolar inputs, and ±2.048V with bipolar

inputs. The internal reference voltage is adjustable to

±1.5% with the Reference-Adjust Circuit of Figure 17.

External Reference

With both the MAX186 and MAX188, an external refer-

ence can be placed at either the input (REFADJ) or the

output (VREF) of the internal buffer amplifier. The

REFADJ input impedance is typically 20kΩfor the

MAX186 and higher than 100kΩfor the MAX188, where

the internal reference is omitted. At VREF, the input

impedance is a minimum of 12kΩfor DC currents.

During conversion, an external reference at VREF must

be able to deliver up to 350µA DC load current and have

an output impedance of 10Ωor less. If the reference has

higher output impedance or is noisy, bypass it close to

the VREF pin with a 4.7µF capacitor.

Low-Power, 8-Channel,

Serial 12-Bit ADCs

18 Maxim Integrated

MAX186/MAX188

1000

0 100 300 500

MAX186

FULL POWER-DOWN

100

MAX186-14A

CONVERSIONS PER CHANNEL PER SECOND

200 400

2ms FASTPD WAIT

400kHz EXTERNAL CLOCK

INTERNAL COMPENSATION

50 150 250 350 450

8 CHANNELS

1 CHANNEL

AVG. SUPPLY CURRENT (µA)

10,000

MAX186/MAX188

FAST POWER-DOWN

100

1000

CONVERSIONS PER CHANNEL PER SECOND

8 CHANNELS

1 CHANNEL

4k 6k 8k 10k 12k 14k 16k 18k

2MHz EXTERNAL CLOCK

EXTERNAL COMPENSATION

50µs WAIT

AVG. SUPPLY CURRENT (µA)

Figure 14a. MAX186 Supply Current vs. Sample Rate/Second,

FULLPD, 400kHz Clock

Figure 14b. MAX186/MAX188 Supply Current vs. Sample

Rate/Second, FASTPD, 2MHz Clock

3.0

2.5

2.0

1.5

1.0

0.5

0.0001 0.001 0.01 0.1 1 10

TIME IN SHUTDOWN (sec)

POWER-UP DELAY (ms)

Figure 14c. Typical Power-Up Delay vs. Time in Shutdown

Using the buffered REFADJ input avoids external

buffering of the reference. To use the direct VREF input,

disable the internal buffer by tying REFADJ to VDD.

Transfer Function and Gain Adjust

Figure 15 depicts the nominal, unipolar input/output

(I/O) transfer function, and Figure 16 shows the bipolar

input/output transfer function. Code transitions occur

halfway between successive integer LSB values. Output

coding is binary with 1 LSB = 1.00mV (4.096V/4096) for

unipolar operation and 1 LSB = 1.00mV ((4.096V/2 -

-4.096V/2)/4096) for bipolar operation.

Figure 17, the MAX186 Reference-Adjust Circuit, shows

how to adjust the ADC gain in applications that use the

internal reference. The circuit provides ±1.5%

(±65LSBs) of gain adjustment range.

Layout, Grounding, Bypassing

For best performance, use printed circuit boards.

Wire-wrap boards are not recommended. Board layout

should ensure that digital and analog signal lines are

separated from each other. Do not run analog and digi-

tal (especially clock) lines parallel to one another, or

digital lines underneath the ADC package.

Figure 18 shows the recommended system ground

connections. A single-point analog ground (“star”

ground point) should be established at AGND, sepa-

rate from the logic ground. All other analog grounds

and DGND should be connected to this ground. No

other digital system ground should be connected to

this single-point analog ground. The ground return to

the power supply for this ground should be low imped-

ance and as short as possible for noise-free operation.

High-frequency noise in the VDD power supply may

affect the high-speed comparator in the ADC. Bypass

these supplies to the single-point analog ground with

0.1µF and 4.7µF bypass capacitors close to the

MAX186/MAX188. Minimize capacitor lead lengths for

best supply-noise rejection. If the +5V power supply is

very noisy, a 10Ωresistor can be connected as a low-

pass filter, as shown in Figure 18.

Low-Power, 8-Channel,

Serial 12-Bit ADCs

Maxim Integrated 19

MAX186/MAX188

OUTPUT CODE

FULL-SCALE

TRANSITION

11 . . . 111

11 . . . 110

11 . . . 101

00 . . . 011

00 . . . 010

00 . . . 001

00 . . . 000

123

0FS

FS - 3/2LSB

FS = +4.096V

1LSB = FS

4096

INPUT VOLTAGE (LSBs)

011 . . . 111

011 . . . 110

000 . . . 010

000 . . . 001

000 . . . 000

111 . . . 111

111 . . . 110

111 . . . 101

100 . . . 001

100 . . . 000

-FS 0V

INPUT VOLTAGE (LSBs)

+FS - 1LSB

FS = +4.096

1LSB = +4.096

4096

+5V

510kΩ

100kΩ

24kΩ0.01μF

12 REFADJ

MAX186

Figure 17. MAX186 Reference-Adjust Circuit

Figure 15. MAX186/MAX188 Unipolar Transfer Function,

4.096V = Full Scale

Figure 16. MAX186/MAX188 Bipolar Transfer Function,

±4.096V/2 = Full Scale

High-Speed Digital Interfacing with QSPI

The MAX186/MAX188 can interface with QSPI at high

throughput rates using the circuit in Figure 19. This

QSPI circuit can be programmed to do a conversion on

each of the eight channels. The result is stored in mem-

ory without taxing the CPU since QSPI incorporates its

own micro-sequencer. Figure 19 depicts the MAX186,

but the same circuit could be used with the MAX188 by

adding an external reference to VREF and connecting

REFADJ to VDD.

Figure 20 details the code that sets up QSPI for

autonomous operation. In external clock mode, the

MAX186/MAX188 perform a single-ended, unipolar con-

version on each of their eight analog input channels.

Figure 21, QSPI Assembly-Code Timing, shows the tim-

ing associated with the assembly code of Figure 20. The

first byte clocked into the MAX186/MAX188 is the control

byte, which triggers the first conversion on CH0. The last

two bytes clocked into the MAX186/MAX188 are all zero

and clock out the results of the CH7 conversion.

Low-Power, 8-Channel,

Serial 12-Bit ADCs

20 Maxim Integrated

MAX186/MAX188

+5V -5V GND

SUPPLIES

DGND+5VDGNDVSS

AGNDVDD

DIGITAL

CIRCUITRY

MAX186/MAX188

R* = 10Ω

* OPTIONAL

Figure 18. Power-Supply Grounding Connection

MAX186

CH0

CH1

CH2

CH3

CH4

CH5

CH6

CH7

VSS

SHDN

VDD

SCLK

DIN

SSTRB

DOUT

DGND

AGND

REFADJ

VREF

VDDI, VDDE, VDDSYN, VSTBY

SCK

PCS0

MOSI

MISO

* CLOCK CONNECTIONS NOT SHOWN

VSSI VSSE

MC68HC16

0.1μF 4.7μF

0.01μF

0.1μF4.7μF

ANALOG

INPUTS

+5V

Figure 19. MAX186 QSPI Connection

Low-Power, 8-Channel,

Serial 12-Bit ADCs

Maxim Integrated 21

MAX186/MAX188

*Title : MAX186.ASM

* Description :

* This is a shell program for using a stand-alone 68HC16 without any external memory. The internal 1K RAM

* is put into bank $0F to maintain 68HC11 code compatibility. This program was written with software

* provided in the Motorola 68HC16 Evaluation Kit.

* Roger J.A. Chen, Applications Engineer

* MAXIM Integrated Products

* November 20, 1992

******************************************************************************************************************************************************

INCLUDE ‘EQUATES.ASM’ ;Equates for common reg addrs

INCLUDE ‘ORG00000.ASM’ ;initialize reset vector

INCLUDE ‘ORG00008.ASM’ ;initialize interrupt vectors

ORG $0200 ;start program after interrupt vectors

INCLUDE ‘INITSYS.ASM’ ;set EK=F,XK=0,YK=0,ZK=0

;set sys clock at 16.78 MHz, COP off

INCLUDE ‘INITRAM.ASM’ ;turn on internal SRAM at $10000

;set stack (SK=1, SP=03FE)

MAIN:

JSR INITQSPI

MAINLOOP:

JSR READ186

WAIT:

LDAA SPSR

ANDA #$80

BEQ WAIT ;wait for QSPI to finish

BRA MAINLOOP

ENDPROGRAM:

INITQSPI:

;This routine sets up the QSPI microsequencer to operate on its own.

;The sequencer will read all eight channels of a MAX186/MAX188 each time

;it is triggered. The A/D converter results will be left in the

;receive data RAM. Each 16 bit receive data RAM location will

;have a leading zero, 12 bits of conversion result and three zeros.

;

;Receive RAM Bits 15 14 13 12 11 10 09 08 07 06 05 04 03 02 01 00

;A/D Result 0 MSB LSB 0 0 0

***** Initialize the QSPI Registers ******

PSHA

PSHB

LDAA #%01111000

STAA QPDR ;idle state for PCS0-3 = high

LDAA #%01111011

STAA QPAR ;assign port D to be QSPI

LDAA #%01111110

STAA QDDR ;only MISO is an input

LDD #$8008

STD SPCR0 ;master mode,16 bits/transfer,

;CPOL=CPHA=0,1MHz Ser Clock

LDD #$0000

STD SPCR1 ;set delay between PCS0 and SCK,

Figure 20. MAX186/MAX188 Assembly-Code Listing

;set delay between transfers

LDD #$0800

STD SPCR2 ;set ENDQP to $8 for 9 transfers

***** Initialize QSPI Command RAM *****

LDAA #$80 ;CONT=1,BITSE=0,DT=0,DSCK=0,PCS0=ACTIVE

STAA $FD40 ;store first byte in COMMAND RAM

LDAA #$C0 ;CONT=1,BITSE=1,DT=0,DSCK=0,PCS0=ACTIVE

STAA $FD41

STAA $FD42

STAA $FD43

STAA $FD44

STAA $FD45

STAA $FD46

STAA $FD47

LDAA #$40 ;CONT=0,BITSE=1,DT=0,DSCK=0,PCS0=ACTIVE

STAA $FD48

***** Initialize QSPI Transmit RAM *****

LDD #$008F

STD $FD20

LDD #$00CF

STD $FD22

LDD #$009F

STD $FD24

LDD #$00DF

STD $FD26

LDD #$00AF

STD $FD28

LDD #$00EF

STD $FD2A

LDD #$00BF

STD $FD2C

LDD #$00FF

STD $FD2E

LDD #$0000

STD $FD30

PULB

PULA

RTS

READ186:

;This routine triggers the QSPI microsequencer to autonomously

;trigger conversions on all 8 channels of the MAX186. Each

;conversion result is stored in the receive data RAM.

PSHA

LDAA #$80

ORAA SPCR1

STAA SPCR1 ;just set SPE

PULA

RTS

***** Interrupts/Exceptions *****

BDM: BGND ;exception vectors point here

;and put the user in background debug mode

Low-Power, 8-Channel,

Serial 12-Bit ADCs

22 Maxim Integrated

MAX186/MAX188

Figure 20. MAX186/MAX188 Assembly-Code Listing (continued)

Low-Power, 8-Channel,

Serial 12-Bit ADCs

Maxim Integrated 23

MAX186/MAX188

TMS320C3x to MAX186 Interface

Figure 22 shows an application circuit to interface the

MAX186/MAX188 to the TMS320 in external clock

mode. The timing diagram for this interface circuit is

shown in Figure 23.

Use the following steps to initiate a conversion in the

MAX186/MAX188 and to read the results:

1) The TMS320 should be configured with CLKX (trans-

mit clock) as an active-high output clock and CLKR

(TMS320 receive clock) as an active-high input clock.

CLKX and CLKR of the TMS320 are connected

together with the SCLK input of the MAX186/MAX188.

2) The MAX186/MAX188 CS is driven low by the XF_

I/O port of the TMS320 to enable data to be clocked

into DIN of the MAX186/MAX188.

3) An 8-bit word (1XXXXX11) should be written to the

MAX186/MAX188 to initiate a conversion and place

the device into external clock mode. Refer to Table

2 to select the proper XXXXX bit values for your spe-

cific application.

4) The SSTRB output of the MAX186/MAX188 is moni-

tored via the FSR input of the TMS320. A falling

edge on the SSTRB output indicates that the conver-

sion is in progress and data is ready to be received

from the MAX186/MAX188.

CLKX

CLKR

FSR

SCLK

DIN

DOUT

SSTRB

TMS320C3x MAX186

MAX188

Figure 22. MAX186/MAX188 to TMS320 Serial Interface

• • • •

SCLK

SSTRB

DIN

Figure 21. QSPI Assembly-Code Timing

5) The TMS320 reads in one data bit on each of the

next 16 rising edges of SCLK. These data bits rep-

resent the 12-bit conversion result followed by four

trailing bits, which should be ignored.

6) Pull CS high to disable the MAX186/MAX188 until

the next conversion is initiated.

Low-Power, 8-Channel,

Serial 12-Bit ADCs

24 Maxim Integrated

MAX186/MAX188

_Ordering Information (continued)

SCLK

DIN

SSTRB

DOUT

START SEL2 SEL1 SEL0 UNI/BIP SGL/DIF PD1 PD0

MSB B10 B1 LSB HIGH

IMPEDANCE

HIGH

IMPEDANCE

Figure 23. TMS320 Serial Interface Timing Diagram

Chip Information

Substrate connected to VDD

VDD

I/O

SCK (SK)*

MOSI (SO)

MISO (SI)

VSS

SHDN

SSTRB

DOUT

DIN

SCLK

VSS

AGND

DGND

VDD

REFADJ

CH7

0.1μF

CH0

+5V

0.01μF

0V to

4.096V

ANALOG

INPUTS

MAX186 CPU

4.7μF

VREF

__________Typical Operating Circuit

†

Parts are offered in grades A, B, C and D (grades defined in

Electrical Characteristics). When ordering, please specify grade.

Contact factory for availability of A-grade in SSOP package.

Dice are specified at +25°C, DC parameters only.

Denotes a lead(Pb)-free/RoHS-compliant package.

PART† TEMP RANGE PIN-PACKAGE

MAX188_CPP+ 0°C to +70°C 20 PDIP

MAX188_CWP+ 0°C to +70°C 20 SO

MAX188_CAP+ 0°C to +70°C 20 SSOP

MAX188DC/D 0°C to +70°C Dice*

MAX188_EPP+ -40°C to +85°C 20 PDIP

MAX188_EWP+ -40°C to +85°C 20 SO

MAX188_EAP+ -40°C to +85°C 20 SSOP

PART TEMP RANGE BOARD TYPE

MAX186EVKIT-DIP 0°C to +70°C Through-Hole

Package Information

For the latest package outline information and land patterns (foot-

prints), go to www.maximintegrated.com/packages. Note that a

“+”, “#”, or “-” in the package code indicates RoHS status only.

Package drawings may show a different suffix character, but the

drawing pertains to the package regardless of RoHS status.

PACKAGE

TYPE

PACKAGE

CODE

OUTLINE

NO.

LAND

PATTERN NO.

20 PDIP P20+3 21-0043 —

20 SO W20+3 21-0042 91-0108

20 SSOP A20+1 21-0056 91-0094

Maxim Integrated cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim Integrated product. No circuit patent

licenses are implied. Maxim Integrated reserves the right to change the circuitry and specifications without notice at any time. The parametric values (min and

max limits) shown in the Electrical Characteristics table are guaranteed. Other parametric values quoted in this data sheet are provided for guidance.

Maxim Integrated 160 Rio Robles, San Jose, CA 95134 USA 1-408-601-1000

Low-Power, 8-Channel,

Serial 12-Bit ADCs

MAX186/MAX188

Revision History

REVISION

NUMBER

REVISION

DATE DESCRIPTION PAGES

CHANGED

0 3/93 Initial release —

5 1/12 Updated the Ordering Information and Electrical Characteristics. 1, 3, 18