EVALUATION KIT AVAILABLE MAX186/MAX188 Low-Power, 8-Channel, Serial 12-Bit ADCs General Description The MAX186/MAX188 are 12-bit data-acquisition systems that combine an 8-channel multiplexer, highbandwidth track/hold, and serial interface together with high conversion speed and ultra-low power consumption. The devices operate with a single +5V supply or dual 5V supplies. The analog inputs are software configurable for unipolar/bipolar and single-ended/differential operation. The 4-wire serial interface directly connects to SPI, QSPITM and MICROWIRE(R) devices without external logic. A serial strobe output allows direct connection to TMS320 family digital signal processors. The MAX186/MAX188 use either the internal clock or an external serial-interface clock to perform successiveapproximation A/D conversions. The serial interface can operate beyond 4MHz when the internal clock is used. ____________________________Features o 8-Channel Single-Ended or 4-Channel Differential Inputs o Single +5V or 5V Operation o Low Power: 1.5mA (Operating Mode) 2A (Power-Down Mode) o Internal Track/Hold, 133kHz Sampling Rate o Internal 4.096V Reference (MAX186) o SPI-/QSPI-/MICROWIRE-/TMS320-Compatible 4-Wire Serial Interface o Software-Configurable Unipolar or Bipolar Inputs o 20-Pin PDIP, SO, SSOP Packages o Evaluation Kit Available Ordering Information PART TEMP RANGE PIN-PACKAGE The MAX186 has an internal 4.096V reference while the MAX188 requires an external reference. Both parts have a reference-buffer amplifier that simplifies gain trim . MAX186_CPP+ 0C to +70C 20 PDIP MAX186_CWP+ 0C to +70C 20 SO MAX186_CAP+ 0C to +70C 20 SSOP The MAX186/MAX188 provide a hard-wired SHDN pin and two software-selectable power-down modes. Accessing the serial interface automatically powers up the devices, and the quick turn-on time allows the MAX186/MAX188 to be shut down between every conversion. Using this technique of powering down between conversions, supply current can be cut to under 10A at reduced sampling rates. MAX186DC/D 0C to +70C Dice* MAX186_EPP+ -40C to +85C 20 PDIP MAX186_EWP+ -40C to +85C 20 SO MAX186_EAP+ -40C to +85C 20 SSOP The MAX186/MAX188 are available in 20-pin PDIP and SO packages, and in a shrink small-outline package (SSOP), that occupies 30% less area than an 8-pin PDIP. For applications that call for a parallel interface, see the MAX180/MAX181 data sheet. For anti-aliasing filters, consult the MAX274/MAX275 data sheet. ________________________Applications Portable Data Logging Data-Acquisition High-Accuracy Process Control Automatic Testing Robotics Battery-Powered Instruments Medical Instruments QSPI is a trademark of Motorola. MICROWIRE is a registered trademark of National Semiconductor. Ordering Information continued on last page. Parts are offered in grades A, B, C and D (grades defined in Electrical Characteristics). When ordering, please specify grade. Contact factory for availability of A-grade in SSOP package. *Dice are specified at +25C, DC parameters only. +Denotes a lead(Pb)-free/RoHS-compliant package. ____________________Pin Configuration TOP VIEW + CH0 1 20 VDD CH1 2 19 SCLK CH2 3 18 CS CH3 4 CH4 5 MAX186 MAX188 17 DIN 16 SSTRB CH5 6 15 DOUT CH6 7 14 DGND CH7 8 13 AGND VSS 9 12 REFADJ 11 VREF SHDN 10 PDIP/SO/SSOP For pricing, delivery, and ordering information, please contact Maxim Direct at 1-888-629-4642, or visit Maxim Integrated's website at www.maximintegrated.com. 19-0123; Rev 5; 1/12 MAX186/MAX188 Low-Power, 8-Channel, Serial 12-Bit ADCs ABSOLUTE MAXIMUM RATINGS VDD to AGND............................................................-0.3V to +6V VSS to AGND ............................................................+0.3V to -6V VDD to VSS ..............................................................-0.3V to +12V AGND to DGND.....................................................-0.3V to +0.3V CH0-CH7 to AGND, DGND .............(VSS - 0.3V) to (VDD + 0.3V) CH0-CH7 Total Input Current...........................................20mA VREF to AGND ...........................................-0.3V to (VDD + 0.3V) REFADJ to AGND.......................................-0.3V to (VDD + 0.3V) Digital Inputs to DGND...............................-0.3V to (VDD + 0.3V) Digital Outputs to DGND ............................-0.3V to (VDD + 0.3V) Digital Output Sink Current .................................................25mA Continuous Power Dissipation (TA = +70C) PDIP (derate 11.11mW/C above +70C) .....................889mW SO (derate 10.00mW/C above +70C) ........................800mW SSOP (derate 8.00mW/C above +70C) .....................640mW Operating Temperature Ranges MAX186_C/MAX188_C ........................................0C to +70C MAX186_E/MAX188_E......................................-40C to +85C Storage Temperature Range .............................-60C to +150C Lead Temperature (soldering, 10s) .................................+300C Soldering Temperature (reflow) .......................................+260C Stresses beyond those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. ELECTRICAL CHARACTERISTICS (VDD = 5V 5%; VSS = 0V or -5V; fCLK = 2.0MHz, external clock (50% duty cycle); 15 clocks/conversion cycle (133ksps); MAX186-- 4.7F capacitor at VREF pin; MAX188--external reference, VREF = 4.096V applied to VREF pin; TA = TMIN to TMAX, unless otherwise noted.) PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS DC ACCURACY (Note 1) Resolution 12 Relative Accuracy (Note 2) Differential Nonlinearity DNL Offset Error Bits MAX186A/MAX188A 0.5 MAX186B/MAX188B 0.5 MAX186C 1.0 MAX188C 0.75 MAX186D/MAX188D 1.0 No missing codes over temperature 1 MAX186A/MAX188A 2.0 MAX186B/MAX188B 3.0 MAX186C/MAX188C 3.0 MAX186D/MAX188D 3.0 MAX186 (all grades) Gain Error (Note 3) External reference 4.096V (MAX188) Gain Temperature Coefficient LSB LSB LSB 3.0 MAX188A 1.5 MAX188B 2.0 MAX188C 2.0 MAX188D 3.0 External reference, 4.096V Channel-to-Channel Offset Matching LSB 0.8 ppm/C 0.1 LSB DYNAMIC SPECIFICATIONS (10kHz sine wave input, 4.096VP-P, 133ksps, 2.0MHz external clock, bipolar input mode) Signal-to-Noise + Distortion Ratio Total Harmonic Distortion (up to the 5th harmonic) THD Spurious-Free Dynamic Range SFDR Channel-to-Channel Crosstalk 2 SINAD 70 dB -80 80 65kHz, VIN = 4.096VP-P (Note 4) dB dB -85 dB Maxim Integrated MAX186/MAX188 Low-Power, 8-Channel, Serial 12-Bit ADCs ELECTRICAL CHARACTERISTICS (continued) (VDD = 5V 5%; VSS = 0V or -5V; fCLK = 2.0MHz, external clock (50% duty cycle); 15 clocks/conversion cycle (133ksps); MAX186-- 4.7F capacitor at VREF pin; MAX188--external reference, VREF = 4.096V applied to VREF pin; TA = TMIN to TMAX, unless otherwise noted.) PARAMETER SYMBOL Small-Signal Bandwidth CONDITIONS MIN -3dB rolloff Full-Power Bandwidth TYP MAX UNITS 4.5 MHz 800 kHz CONVERSION RATE Conversion Time (Note 5) Track/Hold Acquisition Time t CONV Internal clock External clock, 2MHz, 12 clocks/conversion 5.5 10 6 tAZ 1.5 s s Aperture Delay 10 ns Aperture Jitter <50 ps Internal Clock Frequency External Clock Frequency Range 1.7 External compensation, 4.7F 0.1 Internal compensation (Note 6) 0.1 Used for data transfer only MHz 2.0 0.4 MHz 10 ANALOG INPUT Input Voltage Range, Single-Ended and Differential (Note 9) Unipolar, VSS = 0V 0 to VREF Bipolar, VSS = -5V VREF/2 Multiplexer Leakage Current On/off leakage current, VIN = 5V Input Capacitance (Note 6) INTERNAL REFERENCE (MAX186 only, reference buffer enabled) TA = +25C VREF Output Voltage 0.01 4.076 4.096 VREF Short-Circuit Current VREF Tempco Load Regulation (Note 7) Capacitive Bypass at VREF Capacitive Bypass at REFADJ 1 16 4.116 V 30 mA 30 50 30 60 MAX186D 30 2.5 Internal compensation 0 External compensation 4.7 Internal compensation 0.01 External compensation 0.01 REFADJ Adjustment Range A pF MAX186A, MAX186B, MAX186_C MAX186C MAX186_E 0 to 0.5mA output load V ppm/C mV F F 1.5 % EXTERNAL REFERENCE AT VREF (Buffer disabled, VREF = 4.096V) Input Voltage Range Input Current Input Resistance 200 12 Shutdown VREF Input Current Buffer Disable Threshold REFADJ Maxim Integrated VDD + 50mV 2.50 1.5 VDD 50mV 350 20 V A k 10 A V 3 MAX186/MAX188 Low-Power, 8-Channel, Serial 12-Bit ADCs ELECTRICAL CHARACTERISTICS (continued) (VDD = 5V 5%; VSS = 0V or -5V; fCLK = 2.0MHz, external clock (50% duty cycle); 15 clocks/conversion cycle (133ksps); MAX186-- 4.7F capacitor at VREF pin; MAX188--external reference, VREF = 4.096V applied to VREF pin; TA = TMIN to TMAX, unless otherwise noted.) PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS EXTERNAL REFERENCE AT REFADJ Capacitive Bypass at VREF Reference-Buffer Gain REFADJ Input Current Internal compensation mode 0 External compensation mode 4.7 F MAX186 1.678 MAX188 1.638 V/V MAX186 50 MAX188 5 A DIGITAL INPUTS (DIN, SCLK, CS, SHDN) DIN, SCLK, CS Input High Voltage DIN, SCLK, CS Input Low Voltage DIN, SCLK, CS Input Hysteresis VINH 2.4 V VINL VHYST 0.8 V 0.15 V DIN, SCLK, CS Input Leakage IIN VIN = 0V or VDD 1 A DIN, SCLK, CS Input Capacitance CIN (Note 6) 15 pF SHDN Input High Voltage VINH SHDN Input Low Voltage VINL SHDN Input Current, High IINH VSHDN = VDD SHDN Input Current, Low IINL VSHDN = 0V SHDN Input Mid Voltage VIM SHDN Voltage, Open VFLT SHDN Max Allowed Leakage, Mid Input VDD - 0.5 V V 4.0 A -4.0 A 1.5 VSHDN = open VSHDN = open 0.5 VDD -1.5 2.75 -100 V V 100 nA DIGITAL OUTPUTS (DOUT, SSTRB) Output Voltage Low VOL Output Voltage High VOH Three-State Leakage Current Three-State Output Capacitance IL COUT ISINK = 5mA 0.4 ISINK = 16mA ISOURCE = 1mA V 0.3 4 V VCS = 5V VCS = 5V (Note 6) 10 A 15 pF POWER REQUIREMENTS Positive Supply Voltage VDD 5 5% V Negative Supply Voltage VSS 0 or -5 5% V Positive Supply Current Negative Supply Current 4 IDD ISS Operating mode 1.5 Fast power-down 30 70 Full power-down 2 10 Operating mode and fast power-down Full power-down 2.5 50 10 mA A A Maxim Integrated MAX186/MAX188 Low-Power, 8-Channel, Serial 12-Bit ADCs ELECTRICAL CHARACTERISTICS (continued) (VDD = 5V 5%; VSS = 0V or -5V; fCLK = 2.0MHz, external clock (50% duty cycle); 15 clocks/conversion cycle (133ksps); MAX186-- 4.7F capacitor at VREF pin; MAX188--external reference, VREF = 4.096V applied to VREF pin; TA = TMIN to TMAX, unless otherwise noted.) PARAMETER SYMBOL CONDITIONS Positive Supply Rejection (Note 8) PSR Negative Supply Rejection (Note 8) PSR MIN TYP MAX UNITS VDD = 5V 5%; external reference, 4.096V; full-scale input 0.06 0.5 mV VSS = -5V 5%; external reference, 4.096V; full-scale input 0.01 0.5 mV TYP MAX UNITS TIMING CHARACTERISTICS (VDD = 5V 5%; VSS =0V or -5V, TA = TMIN to TMAX, unless otherwise noted.) PARAMETER SYMBOL CONDITIONS MIN Acquisition Time tAZ 1.5 DIN to SCLK Setup tDS 100 DIN to SCLK Hold tDH SCLK Fall to Output Data Valid tDO CLOAD = 100pF CS Fall to Output Enable tDV CS Rise to Output Disable tTR CS to SCLK Rise Setup tCSS 100 ns CS to SCLK Rise Hold tCSH 0 ns SCLK Pulse Width High tCH 200 ns SCLK Pulse Width Low tCL SCLK Fall to SSTRB tSSTRB s ns 0 ns 150 ns CLOAD = 100pF 100 ns CLOAD = 100pF 100 ns MAX18_ _C/E 20 200 ns CLOAD = 100pF 200 ns CS Fall to SSTRB Output Enable (Note 6) tSDV External clock mode only, CLOAD = 100pF 200 ns CS Rise to SSTRB Output Disable (Note 6) tSTR External clock mode only, CLOAD = 100pF 200 ns SSTRB Rise to SCLK Rise (Note 6) tSCK Internal clock mode only 0 ns Note 1: Tested at VDD = 5.0V; VSS = 0V; unipolar input mode. Note 2: Relative accuracy is the deviation of the analog value at any code from its theoretical value after the full-scale range has been calibrated. Note 3: MAX186 - internal reference, offset nulled; MAX188 - external reference (VREF = +4.096V), offset nulled. Note 4: Ground on-channel; sine wave applied to all off channels. Note 5: Conversion time defined as the number of clock cycles times the clock period; clock has 50% duty cycle. Note 6: Guaranteed by design. Not subject to production testing. Note 7: External load should not change during conversion for specified accuracy. Note 8: Measured at VSUPPLY +5% and VSUPPLY -5% only. Note 9: The common-mode range for the analog inputs is from VSS to VDD. Maxim Integrated 5 MAX186/MAX188 Low-Power, 8-Channel, Serial 12-Bit ADCs __________________________________________Typical Operating Characteristics POWER-SUPPLY REJECTION vs. TEMPERATURE CHANNEL-TO-CHANNEL OFFSET MATCHING vs. TEMPERATURE INTERNAL REFERENCE VOLTAGE vs. TEMPERATURE 0.16 0.30 VDD = +5V 5% 0.25 2.456 OFFSET MATCHING (LSBs) 0.20 2.455 VREFADJ (V) PSR (LSBs) 0.14 VSS = 0V or -5V 0.15 0.10 2.454 2.453 0.05 0.00 0.10 0.08 0.06 0.04 0.02 2.452 -0.05 -40 -20 0 -60 -40 -20 0 20 40 60 80 100 120 140 TEMPERATURE (C) 0.12 20 40 60 80 100 120 0 -60 -40 -20 TEMPERATURE (C) 0 20 40 60 80 100 120 140 TEMPERATURE (C) MAX186/MAX188 FFT PLOT - 133kHz 20 0 ft = 10kHz = 133kHz ft =fs10kHz fs = 133kHz TA = +25C AMPLITUDE (dB) -20 -40 -60 -80 -100 -120 -140 0 33.25kHz 66.5kHz FREQUENCY _____________________________________________________________Pin Description 6 PIN NAME 1-8 CH0-CH7 9 VSS FUNCTION Sampling Analog Inputs Negative Supply Voltage. Connect to -5V 5% or AGND 10 SHDN Three-Level Shutdown Input. Pulling SHDN low shuts the MAX186/MAX188 down to 10A (max) supply current, otherwise the MAX186/MAX188 are fully operational. Pulling SHDN high puts the reference-buffer amplifier in internal compensation mode. Leaving SHDN unconnected puts the reference-buffer amplifier in external compensation mode. 11 VREF Reference Voltage for analog-to-digital conversion. Also, output of the reference buffer amplifier (4.096V in the MAX186, 1.638 x REFADJ in the MAX188). Add a 4.7F capacitor to ground when using external compensation mode. Also functions as an input when used with a precision external Maxim Integrated MAX186/MAX188 Low-Power, 8-Channel, Serial 12-Bit ADCs ________________________________________________Pin Description (continued) PIN NAME 12 REFADJ FUNCTION Input to the Reference-Buffer Amplifier. To disable the reference-buffer amplifier, connect REFADJ to VDD. 13 AGND Analog Ground. Also IN- Input for single-ended conversions. 14 DGND Digital Ground 15 DOUT Serial Data Output. Data is clocked out at the falling edge of SCLK. High impedance when CS is high. 16 SSTRB Serial Strobe Output. In internal clock mode, SSTRB goes low when the MAX186/MAX188 begin the A/D conversion and goes high when the conversion is done. In external clock mode, SSTRB pulses high for one clock period before the MSB decision. High impedance when CS is high (external mode). 17 DIN Serial Data Input. Data is clocked in at the rising edge of SCLK. 18 CS Active-Low Chip Select. Data will not be clocked into DIN unless CS is low. When CS is high, DOUT is high impedance. 19 SCLK Serial Clock Input. Clocks data in and out of serial interface. In external clock mode, SCLK also sets the conversion speed. (Duty cycle must be 40% to 60% in external clock mode.) 20 VDD Positive Supply Voltage, +5V 5% +5V 3k DOUT DOUT 3k CLOAD CLOAD DGND DGND a. High-Z to VOH and VOL to VOH b. High-Z to VOL and VOH to VOL Figure 1. Load Circuits for Enable Time +5V 3k DOUT CS SCLK 18 19 DIN 17 SHDN 10 CH0 CH1 CH2 CH3 CH4 CH5 CH6 CH7 1 AGND 13 2 3 4 5 6 CLOAD DGND a VOH to High-Z Figure 2. Load Circuits for Disabled Time Maxim Integrated CLOAD CONTROL LOGIC REFADJ 12 VREF 11 INT CLOCK OUTPUT SHIFT REGISTER ANALOG INPUT MUX 15 16 DOUT SSTRB T/H 7 8 DOUT 3k INPUT SHIFT REGISTER +2.46V REFERENCE (MAX186) CLOCK IN 12-BIT SAR ADC OUT REF A 1.65 20k +4.096V 20 14 MAX186 MAX188 9 VDD DGND VSS DGND b VOL to High-Z Figure 3. Block Diagram 7 MAX186/MAX188 Low-Power, 8-Channel, Serial 12-Bit ADCs _______________Detailed Description The MAX186/MAX188 use a successive-approximation conversion technique and input track/hold (T/H) circuitry to convert an analog signal to a 12-bit digital output. A flexible serial interface provides easy interface to microprocessors. No external hold capacitors are required. Figure 3 shows the block diagram for the MAX186/MAX188. Pseudo-Differential Input The sampling architecture of the ADC's analog comparator is illustrated in the Equivalent Input Circuit (Figure 4). In single-ended mode, IN+ is internally switched to CH0-CH7 and IN- is switched to AGND. In differential mode, IN+ and IN- are selected from pairs of CH0/CH1, CH2/CH3, CH4/CH5 and CH6/CH7. Configure the channels with Table 3 and Table 4. In differential mode, IN- and IN+ are internally switched to either one of the analog inputs. This configuration is pseudo-differential to the effect that only the signal at IN+ is sampled. The return side (IN-) must remain stable within 0.5LSB (0.1LSB for best results) with respect to AGND during a conversion. Accomplish this by connecting a 0.1F capacitor from AIN- (the selected analog input, respectively) to AGND. During the acquisition interval, the channel selected as the positive input (IN+) charges capacitor CHOLD. The acquisition interval spans three SCLK cycles and ends on the falling SCLK edge after the last bit of the input control word has been entered. At the end of the acquisition interval, the T/H switch opens, retaining charge on CHOLD as a sample of the signal at IN+. The conversion interval begins with the input multiplexer switching CHOLD from the positive input (IN+) to the negative input (IN-). In single-ended mode, IN- is simply AGND. This unbalances node ZERO at the input of the comparator. The capacitive DAC adjusts during the remainder of the conversion cycle to restore node ZERO to 0V within the limits of 12-bit resolution. This action is equivalent to transferring a charge of 16pF x [(V IN+) - (V IN-)] from C HOLD to the binary-weighted capacitive DAC, which in turn forms a digital representation of the analog input signal. Track/Hold The T/H enters its tracking mode on the falling clock edge after the fifth bit of the 8-bit control word has been shifted in. The T/H enters its hold mode on the falling clock edge after the eighth bit of the control word has been shifted in. If the converter is set up for 8 12-BIT CAPACITIVE DAC VREF CH0 CH1 INPUT MUX CH4 CH5 CH6 CH7 ZERO 16pF CH2 CH3 COMPARATOR CHOLD - + 10k RS CSWITCH TRACK HOLD T/H SWITCH AGND AT THE SAMPLING INSTANT, THE MUX INPUT SWITCHES FROM THE SELECTED IN+ CHANNEL TO THE SELECTED IN- CHANNEL. SINGLE-ENDED MODE: IN+ = CHO-CH7, IN- = AGND. DIFFERENTIAL MODE: IN+ AND IN- SELECTED FROM PAIRS OF CH0/CH1, CH2/CH3, CH4/CH5, CH6/CH7. Figure 4. Equivalent Input Circuit single-ended inputs, IN- is connected to AGND, and the converter samples the "+" input. If the converter is set up for differential inputs, IN- connects to the "-" input, and the difference of |IN+ - IN-| is sampled. At the end of the conversion, the positive input connects back to IN+, and CHOLD charges to the input signal. The time required for the T/H to acquire an input signal is a function of how quickly its input capacitance is charged. If the input signal's source impedance is high, the acquisition time lengthens and more time must be allowed between conversions. Acquisition time is calculated by: tAZ = 9 x (RS + RIN) x 16pF, where RIN = 5k, RS = the source impedance of the input signal, and tAZ is never less than 1.5s. Note that source impedances below 5k do not significantly affect the AC performance of the ADC. Higher source impedances can be used if an input capacitor is connected to the analog inputs, as shown in Figure 5. Note that the input capacitor forms an RC filter with the input source impedance, limiting the ADC's signal bandwidth. Input Bandwidth The ADC's input tracking circuitry has a 4.5MHz small-signal bandwidth, so it is possible to digitize high-speed transient events and measure periodic signals with bandwidths exceeding the ADC's sampling rate by using undersampling techniques. To avoid high-frequency signals being aliased into the frequency band of interest, anti-alias filtering is recommended. Maxim Integrated MAX186/MAX188 Low-Power, 8-Channel, Serial 12-Bit ADCs VDD +5V OSCILLOSCOPE 0.1F DGND AGND 0V TO 4.096V ANALOG 0.01F INPUT CH7 SCLK VSS MAX186 MAX188 SSTRB CS DOUT* SCLK +5V DIN +5V CH1 CH2 CH3 CH4 DOUT D1 1N4148 C2 0.01F 2MHz OSCILLATOR REFADJ SSTRB VREF SHDN N.C. C1 4.7F +2.5V +2.5V REFERENCE ** * FULL-SCALE ANALOG INPUT, CONVERSION RESULT = $FFF (HEX) **REQUIRED FOR MAX188 ONLY. A POTENTIOMETER MAY BE USED IN PLACE OF THE REFERENCE FOR TEST PURPOSES. Figure 5. Quick-Look Circuit Analog Input Range and Input Protection Internal protection diodes, which clamp the analog input to VDD and VSS, allow the channel input pins to swing from VSS - 0.3V to VDD + 0.3V without damage. However, for accurate conversions near full scale, the inputs must not exceed VDD by more than 50mV, or be lower than VSS by 50mV. If the analog input exceeds 50mV beyond the supplies, do not forward bias the protection diodes of off-channels over two milliamperes, as excessive current will degrade the conversion accuracy of the on-channel. The full-scale input voltage depends on the voltage at VREF. See Tables 1a and 1b. Quick Look To evaluate the analog performance of the MAX186/MAX188 quickly, use the circuit of Figure 5. The MAX186/MAX188 require a control byte to be written to DIN before each conversion. Tying DIN to +5V feeds in control bytes of $FF (HEX), which trigger Maxim Integrated Table 1a. Unipolar Full Scale and Zero Scale Reference Internal Reference (MAX186 only) External Reference at REFADJ at VREF Zero Scale Full Scale 0V +4.096V 0V VREFADJ x A* 0V VREF * A = 1.678 for the MAX186, 1.638 for the MAX188 Table 1b. Bipolar Full Scale, Zero Scale, and Negative Full Scale Reference Internal Reference (MAX186 only) External Reference at REFADJ at VREF Negative Full Scale Zero Scale Full Scale -4.096V/2 0V +4.096V/2 -1/2VREFADJ x A* -1/2 VREF 0V 0V +1/2VREFADJ x A* +1/2 VREF * A = 1.678 for the MAX186, 1.638 for the MAX188 9 MAX186/MAX188 Low-Power, 8-Channel, Serial 12-Bit ADCs single-ended unipolar conversions on CH7 in external clock mode without powering down between conversions. In external clock mode, the SSTRB output pulses high for one clock period before the most significant bit of the 12-bit conversion result comes out of DOUT. Varying the analog input to CH7 should alter the sequence of bits from DOUT. A total of 15 clock cycles is required per conversion. All transitions of the SSTRB and DOUT outputs occur on the falling edge of SCLK. How to Start a Conversion A conversion is started on the MAX186/MAX188 by clocking a control byte into DIN. Each rising edge on SCLK, with CS low, clocks a bit from DIN into the MAX186/MAX188's internal shift register. After CS falls, the first arriving logic "1" bit defines the MSB of the control byte. Until this first "start" bit arrives, any number of logic "0" bits can be clocked into DIN with no effect. Table 2 shows the control-byte format. The MAX186/MAX188 are fully compatible with Microwire and SPI devices. For SPI, select the correct clock polarity and sampling edge in the SPI control registers: set CPOL = 0 and CPHA = 0. Microwire and SPI both transmit a byte and receive a byte at the same time. Using the Typical Operating Circuit, the simplest software interface requires only three 8-bit transfers to perform a conversion (one 8-bit transfer to configure the ADC, and two more 8-bit transfers to clock out the 12-bit conversion result). Example: Simple Software Interface Make sure the CPU's serial interface runs in master mode so the CPU generates the serial clock. Choose a clock frequency from 100kHz to 2MHz. 1) Set up the control byte for external clock mode, call it TB1. TB1 should be of the format: 1XXXXX11 Binary, where the Xs denote the particular channel and conversion-mode selected. Table 2. Control-Byte Format Bit 7 (MSB) Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 (LSB) START SEL2 SEL1 SEL0 UNI/BIP SGL/DIF PD1 PD0 Bit Name Description 7(MSB) START The first logic "1" bit after CS goes low defines the beginning of the control byte. 6 5 4 SEL2 SEL1 SEL0 These three bits select which of the eight channels are used for the conversion. See Tables 3 and 4. 3 UNI/BIP 1 = unipolar, 0 = bipolar. Selects unipolar or bipolar conversion mode. In unipolar mode, an analog input signal from 0V to VREF can be converted; in bipolar mode, the signal can range from -VREF/2 to +VREF/2. 2 SGL/DIF 1 = single ended, 0 = differential. Selects single-ended or differential conversions. In single-ended mode, input signal voltages are referred to AGND. In differential mode, the voltage difference between two channels is measured. See Tables 3 and 4. 1 0(LSB) PD1 PD0 Selects clock and power-down modes. PD1 PD0 Mode 0 0 Full power-down (IQ = 2A) 0 1 Fast power-down (IQ = 30A) 1 0 Internal clock mode 1 1 External clock mode 10 Maxim Integrated MAX186/MAX188 Low-Power, 8-Channel, Serial 12-Bit ADCs DIFF = 1) Table 3. Channel Selection in Single-Ended Mode (SGL/D SEL2 SEL1 SEL0 CH0 0 0 0 + 1 0 0 0 0 1 1 0 1 0 1 0 1 1 0 0 1 1 1 1 1 CH1 CH2 CH3 CH4 CH5 CH6 CH7 AGND - + - + - + - + - + - + - + - DIFF = 0) Table 4. Channel Selection in Differential Mode (SGL/D SEL2 SEL1 SEL0 CH0 CH1 0 0 0 + - 0 0 1 0 1 0 0 1 1 1 0 0 1 0 1 1 1 0 1 1 1 - CH2 CH3 + - - 3) Transmit TB1 and simultaneously receive a byte and call it RB1. Ignore RB1. 4) Transmit a byte of all zeros ($00 HEX) and simultaneously receive byte RB2. 5) Transmit a byte of all zeros ($00 HEX) and simultaneously receive byte RB3. Maxim Integrated CH5 + - CH6 CH7 + - - + + 2) Use a general-purpose I/O line on the CPU to pull CS on the MAX186/MAX188 low. 6) Pull CS on the MAX186/MAX188 high. CH4 + - + Figure 6 shows the timing for this sequence. Bytes RB2 and RB3 will contain the result of the conversion padded with one leading zero and three trailing zeros. The total conversion time is a function of the serial clock frequency and the amount of dead time between 8-bit transfers. Make sure that the total conversion time does not exceed 120s, to avoid excessive T/H droop. Digital Output In unipolar input mode, the output is straight binary (see Figure 15). For bipolar inputs, the output is twos-complement (see Figure 16). Data is clocked out at the falling edge of SCLK in MSB-first format. 11 MAX186/MAX188 Low-Power, 8-Channel, Serial 12-Bit ADCs CS tACQ SCLK 1 4 8 START SEL2 SEL1 SEL0 UNI/ BIP DIN SCL/ PD1 DIFF 12 16 20 24 PD0 RB3 RB2 SSTRB RB1 B11 MSB DOUT B9 B8 ACQUISITION IDLE A/D STATE B10 B7 B6 B5 B4 B3 B2 B1 CONVERSION B0 LSB FILLED WITH ZEROS IDLE 1.5s (CLK = 2MHz) Figure 6. 24-Bit External Clock Mode Conversion Timing (SPI, QSPI and Microwire Compatible) *** CS tCSH tCSS tCL tCH SCLK tCSH *** tDS tDH *** DIN tDV tDO tTR *** DOUT Figure 7. Detailed Serial-Interface Timing Internal and External Clock Modes The MAX186/MAX188 may use either an external serial clock or the internal clock to perform the successive-approximation conversion. In both clock modes, the external clock shifts data in and out of the MAX186/MAX188. The T/H acquires the input signal as the last three bits of the control byte are clocked into DIN. Bits PD1 and PD0 of the control byte program the clock mode. Figures 7 through 10 show the timing characteristics common to both modes. External Clock In external clock mode, the external clock not only shifts data in and out, it also drives the analog-to-digital con- 12 version steps. SSTRB pulses high for one clock period after the last bit of the control byte. Successive-approximation bit decisions are made and appear at DOUT on each of the next 12 SCLK falling edges (see Figure 6). SSTRB and DOUT go into a high-impedance state when CS goes high; after the next CS falling edge, SSTRB will output a logic low. Figure 8 shows the SSTRB timing in external clock mode. The conversion must complete in some minimum time, or else droop on the sample-and-hold capacitors may degrade conversion results. Use internal clock mode if the clock period exceeds 10s, or if serial-clock interruptions could cause the conversion interval to exceed 120s. Maxim Integrated MAX186/MAX188 Low-Power, 8-Channel, Serial 12-Bit ADCs *** CS *** tSTR tSDV SSTRB *** *** tSSTRB SCLK tSSTRB **** *** * PD0 CLOCKED IN Figure 8. External Clock Mode SSTRB Detailed Timing CS SCLK DIN 1 2 3 4 5 START SEL2 SEL1 SEL0 UNI/ DIP 7 8 SCL/ PD1 DIFF PD0 6 9 10 11 12 18 19 20 21 22 23 24 SSTRB tCONV B11 MSB DOUT A/D STATE IDLE ACQUISITION CONVERSION 10s MAX B10 B9 B2 B1 B0 LSB FILLED WITH ZEROS IDLE 1.5s (CLK = 2MHz) Figure 9. Internal Clock Mode Timing Internal Clock In internal clock mode, the MAX186/MAX188 generate their own conversion clock internally. This frees the microprocessor from the burden of running the SAR conversion clock, and allows the conversion results to be read back at the processor's convenience, at any clock rate from zero to typically 10MHz. SSTRB goes low at the start of the conversion and then goes high when the conversion is complete. SSTRB will be low for a maximum of 10s, during which time SCLK should remain low for best noise performance. An internal register stores data when the conversion is in progress. SCLK clocks the data out at this register at any time after the conversion is complete. After SSTRB goes high, the next falling clock edge Maxim Integrated will produce the MSB of the conversion at DOUT, followed by the remaining bits in MSB-first format (see Figure 9). CS does not need to be held low once a conversion is started. Pulling CS high prevents data from being clocked into the MAX186/MAX188 and threestates DOUT, but it does not adversely effect an internal clock-mode conversion already in progress. When internal clock mode is selected, SSTRB does not go into a high-impedance state when CS goes high. Figure 10 shows the SSTRB timing in internal clock mode. In internal clock mode, data can be shifted in and out of the MAX186/MAX188 at clock rates exceeding 4.0MHz, provided that the minimum acquisition time, tAZ, is kept above 1.5s. 13 MAX186/MAX188 Low-Power, 8-Channel, Serial 12-Bit ADCs CS * * * tCONV tCSS tSCK tCSH SSTRB * * * tSSTRB SCLK * * * PD0 CLOCK IN NOTE: FOR BEST NOISE PERFORMANCE, KEEP SCLK LOW DURING CONVERSION. Figure 10. Internal Clock Mode SSTRB Detailed Timing Data Framing The falling edge of CS does not start a conversion on the MAX186/MAX188. The first logic high clocked into DIN is interpreted as a start bit and defines the first bit of the control byte. A conversion starts on the falling edge of SCLK, after the eighth bit of the control byte (the PD0 bit) is clocked into DIN. The start bit is defined as: The first high bit clocked into DIN with CS low anytime the converter is idle, e.g. after VCC is applied. OR The first high bit clocked into DIN after bit 5 of a conversion in progress is clocked onto the DOUT pin. If a falling edge on CS forces a start bit before bit 5 (B5) becomes available, then the current conversion will be terminated and a new one started. Thus, the fastest the MAX186/MAX188 can run is 15 clocks per conversion. Figure 11a shows the serial-interface timing necessary to perform a conversion every 15 SCLK cycles in external clock mode. If CS is low and SCLK is continuous, guarantee a start bit by first clocking in 16 zeros. Most microcontrollers require that conversions occur in multiples of 8 SCLK clocks; 16 clocks per conversion will typically be the fastest that a microcontroller can drive the MAX186/MAX188. Figure 11b shows the serial-interface timing necessary to perform a conversion every 16 SCLK cycles in external clock mode. 14 __________ Applications Information Power-On Reset When power is first applied and if SHDN is not pulled low, internal power-on reset circuitry will activate the MAX186/MAX188 in internal clock mode, ready to convert with SSTRB = high. After the power supplies have been stabilized, the internal reset time is 100s and no conversions should be performed during this phase. SSTRB is high on power-up and, if CS is low, the first logical 1 on DIN will be interpreted as a start bit. Until a conversion takes place, DOUT will shift out zeros. Reference-Buffer Compensation In addition to its shutdown function, the SHDN pin also selects internal or external compensation. The compensation affects both power-up time and maximum conversion speed. Compensated or not, the minimum clock rate is 100kHz due to droop on the sample-and-hold. To select external compensation, open SHDN. See the Typical Operating Circuit, which uses a 4.7F capacitor at VREF. A value of 4.7F or greater ensures stability and allows operation of the converter at the full clock speed of 2MHz. External compensation increases power-up time (see the Choosing Power-Down Mode section, and Table 5). Internal compensation requires no external capacitor at VREF, and is selected by pulling SHDN high. Internal compensation allows for shortest power-up times, but is only available using an external clock and reduces the maximum clock rate to 400kHz. Maxim Integrated MAX186/MAX188 Low-Power, 8-Channel, Serial 12-Bit ADCs CS 1 8 1 8 1 SCLK S DIN S CONTROL BYTE 0 CONTROL BYTE 1 CONTROL BYTE 2 B11 B10 B9 B8 B7 B6 B5 B4 B3 B2 B1 B0 B11 B10 B9 B8 B7 B6 B5 B4 B3 B2 B1 B0 DOUT S CONVERSION RESULT 1 CONVERSION RESULT 0 SSTRB Figure 11a. External Clock Mode, 15 Clocks/Conversion Timing CS *** SCLK *** DIN S DOUT S CONTROL BYTE 0 B11 B10 B9 B8 B7 B6 B5 B4 B3 B2 B1 B0 CONVERSION RESULT 0 *** CONTROL BYTE 1 B11 B10 B9 B8 *** CONVERSION RESULT 1 Figure 11b. External Clock Mode, 16 Clocks/Conversion Timing Power-Down Choosing Power-Down Mode You can save power by placing the converter in a low-current shutdown state between conversions. Select full power-down or fast power-down mode via bits 7 and 8 of the DIN control byte with SHDN high or open (see Tables 2 and 6). Pull SHDN low at any time to shut down the converter completely. SHDN overrides bits 7 and 8 of DIN word (see Table 7). Full power-down mode turns off all chip functions that draw quiescent current, reducing IDD and ISS typically to 2A. Fast power-down mode turns off all circuitry except the bandgap reference. With the fast power-down mode, the supply current is 30A. Power-up time can be shortened to 5s in internal compensation mode. In both software shutdown modes, the serial interface remains operational, however, the ADC will not convert. Table 5 illustrates how the choice of reference-buffer compensation and power-down mode affects both power-up delay and maximum sample rate. In external compensation mode, the power-up time is 20ms with a 4.7F compensation capacitor (200ms with a 33F capacitor) when the capacitor is fully discharged. In fast power-down, you can eliminate start-up time by Maxim Integrated using low-leakage capacitors that will not discharge more than 1/2LSB while shut down. In shutdown, the capacitor has to supply the current into the reference (1.5A typ) and the transient currents at power-up. Figures 12a and 12b illustrate the various power-down sequences in both external and internal clock modes. Software Power-Down Software power-down is activated using bits PD1 and PD0 of the control byte. As shown in Table 6, PD1 and PD0 also specify the clock mode. When software shutdown is asserted, the ADC will continue to operate in the last specified clock mode until the conversion is complete. Then the ADC powers down into a low quiescent-current state. In internal clock mode, the interface remains active and conversion results may be clocked out while the MAX186/MAX188 have already entered a software power-down. The first logical 1 on DIN will be interpreted as a start bit, and powers up the MAX186/MAX188. Following the start bit, the data input word or control byte also determines clock and power-down modes. For example, if the DIN word contains PD1 = 1, then the chip will remain powered up. If PD1 = 0, a power-down will resume after one conversion. 15 MAX186/MAX188 Low-Power, 8-Channel, Serial 12-Bit ADCs CLOCK MODE INTERNAL EXTERNAL EXTERNAL SHDN SETS FAST POWER-DOWN MODE SETS EXTERNAL CLOCK MODE DIN S X X X X X 1 1 S X X X X X 0 1 DOUT DATA VALID (12 DATA BITS) MODE POWERED UP SETS EXTERNAL CLOCK MODE S X X X X X 1 1 DATA VALID (12 DATA BITS) VALID DATA INVALID FAST POWER-DOWN POWERED UP FULL POWER DOWN POWERED UP Figure 12a. Timing Diagram Power-Down Modes, External Clock Table 5. Typical Power-Up Delay Times Reference Buffer ReferenceBuffer Compensation Mode Enabled Enabled Enabled External Enabled External VREF Capacitor (F) PowerDown Mode Power-Up Delay (s) Internal Fast 5 26 Internal Full 300 26 4.7 Fast See Figure 14c 133 4.7 Full See Figure 14c 133 Disabled Fast 2 133 Disabled Full 2 133 Table 6. Software Shutdown and Clock Mode Table 7. Hard-Wired Shutdown and Compensation Mode PD1 PD0 1 1 External Clock Mode SHDN State Device Mode Reference-Buffer Compensation 1 0 Internal Clock Mode 1 Enabled Internal Compensation 0 1 Fast Power-Down Mode Open Enabled External Compensation 0 0 Full Power-Down Mode 0 16 Device Mode Maximum Sampling Rate (ksps) Full Power-Down N/A Maxim Integrated MAX186/MAX188 Low-Power, 8-Channel, Serial 12-Bit ADCs CLOCK MODE INTERNAL CLOCK MODE SETS FULL POWER-DOWN SETS INTERNAL CLOCK MODE DIN S X X X X X 1 0 S X X X X X 0 0 DOUT S DATA VALID DATA VALID CONVERSION SSTRB CONVERSION FULL POWER-DOWN POWERED UP MODE POWERED UP Figure 12b. Timing Diagram Power-Down Modes, Internal Clock Hardware Power-Down The SHDN pin places the converter into the full power-down mode. Unlike with the software shut-down modes, conversion is not completed. It stops coincidentally with SHDN being brought low. There is no power-up delay if an external reference is used and is not shut down. The SHDN pin also selects internal or external reference compensation (see Table 7). Power-Down Sequencing The MAX186/MAX188 auto power-down modes can save considerable power when operating at less than maximum sample rates. The following discussion illustrates the various power-down sequences. Lowest Power at up to 500 Conversions/Channel/Second The following examples illustrate two different power-down sequences. Other combinations of clock rates, compensation modes, and power-down modes may give lowest power consumption in other applications. Figure 14a depicts the MAX186 power consumption for one or eight channel conversions utilizing full power-down mode and internal reference compensation. A 0.01F bypass capacitor at REFADJ forms an RC filter with the internal 20k reference resistor with a 0.2ms time constant. To achieve full 12-bit accuracy, 10 time constants or 2ms are required after power-up. Waiting 2ms in FASTPD mode instead of full power-up will reduce the power consumption by a factor of 10 or more. This is achieved by using the sequence shown in Figure 13. COMPLETE CONVERSION SEQUENCE 2ms WAIT DIN CH1 (ZEROS) 1 00 FULLPD 1 01 FASTPD 1 (ZEROS) CH7 11 NOPD 1 00 FULLPD 1 01 FASTPD 2.5V REFADJ 0V 4V = RC = 20k x CREFADJ VREF 0V tBUFFEN 15s Figure 13. MAX186 FULLPD/FASTPD Power-Up Sequence Maxim Integrated 17 MAX186/MAX188 Low-Power, 8-Channel, Serial 12-Bit ADCs MAX186/MAX188 FAST POWER-DOWN 2ms FASTPD WAIT 400kHz EXTERNAL CLOCK INTERNAL COMPENSATION 8 CHANNELS 100 1 CHANNEL 10 1 10,000 AVG. SUPPLY CURRENT (A) AVG. SUPPLY CURRENT (A) 1000 MAX186-14A MAX186 FULL POWER-DOWN 8 CHANNELS 1000 1 CHANNEL 100 2MHz EXTERNAL CLOCK EXTERNAL COMPENSATION 50s WAIT 10 0 50 100 150 200 250 300 350 400 450 500 0 2k CONVERSIONS PER CHANNEL PER SECOND Figure 14a. MAX186 Supply Current vs. Sample Rate/Second, FULLPD, 400kHz Clock 4k 6k 8k 10k 12k 14k 16k 18k CONVERSIONS PER CHANNEL PER SECOND Figure 14b. MAX186/MAX188 Supply Current vs. Sample Rate/Second, FASTPD, 2MHz Clock Lowest Power at Higher Throughputs External and Internal References The MAX186 can be used with an internal or external reference, whereas an external reference is required for the MAX188. Diode D1 shown in the Typical Operating Circuit ensures correct start-up. Any standard signal diode can be used. For both parts, an external reference can either be connected directly at the VREF terminal or at the REFADJ pin. An internal buffer is designed to provide 4.096V at VREF for both the MAX186 and MAX188. The MAX186's internally trimmed 2.46V reference is buffered with a gain of 1.678. The MAX188's buffer is trimmed with a buffer gain of 1.638 to scale an external 2.5V reference at REFADJ to 4.096V at VREF. MAX186 Internal Reference The full-scale range of the MAX186 with internal reference is 4.096V with unipolar inputs, and 2.048V with bipolar inputs. The internal reference voltage is adjustable to 1.5% with the Reference-Adjust Circuit of Figure 17. 18 3.0 2.5 POWER-UP DELAY (ms) Figure 14b shows the power consumption with external-reference compensation in fast power-down, with one and eight channels converted. The external 4.7F compensation requires a 50s wait after power-up, accomplished by 75 idle clocks after a dummy conversion. This circuit combines fast multi-channel conversion with lowest power consumption possible. Full power-down mode may provide increased power savings in applications where the MAX186/MAX188 are inactive for long periods of time, but where intermittent bursts of high-speed conversions are required. 2.0 1.5 1.0 0.5 0 0.0001 0.001 0.01 0.1 1 10 TIME IN SHUTDOWN (sec) Figure 14c. Typical Power-Up Delay vs. Time in Shutdown External Reference With both the MAX186 and MAX188, an external reference can be placed at either the input (REFADJ) or the output (VREF) of the internal buffer amplifier. The REFADJ input impedance is typically 20k for the MAX186 and higher than 100k for the MAX188, where the internal reference is omitted. At VREF, the input impedance is a minimum of 12k for DC currents. During conversion, an external reference at VREF must be able to deliver up to 350A DC load current and have an output impedance of 10 or less. If the reference has higher output impedance or is noisy, bypass it close to the VREF pin with a 4.7F capacitor. Maxim Integrated MAX186/MAX188 Low-Power, 8-Channel, Serial 12-Bit ADCs OUTPUT CODE FULL-SCALE TRANSITION 11 . . . 111 011 . . . 111 011 . . . 110 11 . . . 110 FS = +4.096 2 1LSB = +4.096 4096 11 . . . 101 000 . . . 010 000 . . . 001 FS = +4.096V 1LSB = FS 4096 000 . . . 000 111 . . . 111 111 . . . 110 111 . . . 101 00 . . . 011 00 . . . 010 100 . . . 001 00 . . . 001 100 . . . 000 00 . . . 000 0 1 2 3 0V -FS FS +FS - 1LSB INPUT VOLTAGE (LSBs) INPUT VOLTAGE (LSBs) FS - 3/2LSB Figure 15. MAX186/MAX188 Unipolar Transfer Function, 4.096V = Full Scale Figure 16. MAX186/MAX188 Bipolar Transfer Function, 4.096V/2 = Full Scale Using the buffered REFADJ input avoids external buffering of the reference. To use the direct VREF input, disable the internal buffer by tying REFADJ to VDD. +5V MAX186 Transfer Function and Gain Adjust Figure 15 depicts the nominal, unipolar input/output (I/O) transfer function, and Figure 16 shows the bipolar input/output transfer function. Code transitions occur halfway between successive integer LSB values. Output coding is binary with 1 LSB = 1.00mV (4.096V/4096) for unipolar operation and 1 LSB = 1.00mV ((4.096V/2 -4.096V/2)/4096) for bipolar operation. Figure 17, the MAX186 Reference-Adjust Circuit, shows how to adjust the ADC gain in applications that use the internal reference. The circuit provides 1.5% (65LSBs) of gain adjustment range. Layout, Grounding, Bypassing For best performance, use printed circuit boards. Wire-wrap boards are not recommended. Board layout should ensure that digital and analog signal lines are separated from each other. Do not run analog and digital (especially clock) lines parallel to one another, or digital lines underneath the ADC package. Figure 18 shows the recommended system ground connections. A single-point analog ground ("star" ground point) should be established at AGND, separate from the logic ground. All other analog grounds Maxim Integrated 510k 100k 12 24k REFADJ 0.01F Figure 17. MAX186 Reference-Adjust Circuit and DGND should be connected to this ground. No other digital system ground should be connected to this single-point analog ground. The ground return to the power supply for this ground should be low impedance and as short as possible for noise-free operation. High-frequency noise in the VDD power supply may affect the high-speed comparator in the ADC. Bypass these supplies to the single-point analog ground with 0.1F and 4.7F bypass capacitors close to the MAX186/MAX188. Minimize capacitor lead lengths for best supply-noise rejection. If the +5V power supply is very noisy, a 10 resistor can be connected as a lowpass filter, as shown in Figure 18. 19 MAX186/MAX188 Low-Power, 8-Channel, Serial 12-Bit ADCs High-Speed Digital Interfacing with QSPI The MAX186/MAX188 can interface with QSPI at high throughput rates using the circuit in Figure 19. This QSPI circuit can be programmed to do a conversion on each of the eight channels. The result is stored in memory without taxing the CPU since QSPI incorporates its own micro-sequencer. Figure 19 depicts the MAX186, but the same circuit could be used with the MAX188 by adding an external reference to VREF and connecting REFADJ to VDD. SUPPLIES +5V -5V GND R* = 10 VDD AGND VSS DGND +5V Figure 20 details the code that sets up QSPI for autonomous operation. In external clock mode, the MAX186/MAX188 perform a single-ended, unipolar conversion on each of their eight analog input channels. Figure 21, QSPI Assembly-Code Timing, shows the timing associated with the assembly code of Figure 20. The first byte clocked into the MAX186/MAX188 is the control byte, which triggers the first conversion on CH0. The last two bytes clocked into the MAX186/MAX188 are all zero and clock out the results of the CH7 conversion. DGND DIGITAL CIRCUITRY MAX186/MAX188 * OPTIONAL Figure 18. Power-Supply Grounding Connection +5V + ANALOG INPUTS 1 CH0 V DD 20 2 CH1 SCLK 19 3 CH2 CS 18 4 CH3 DIN 17 MAX186 5 CH4 SSTRB 16 6 CH5 DOUT 15 7 CH6 DGND 14 8 CH7 AGND 13 9 V SS REFADJ 12 10 SHDN VREF 11 0.1 F V DDI , V DDE , V DDSYN , V STBY 4.7 F SCK PCS0 MC68HC16 MOSI MISO 0.1 F + 4.7 F 0.01 F V SSI VSSE * CLOCK CONNECTIONS NOT SHOWN Figure 19. MAX186 QSPI Connection 20 Maxim Integrated MAX186/MAX188 Low-Power, 8-Channel, Serial 12-Bit ADCs *Title : MAX186.ASM * Description : * This is a shell program for using a stand-alone 68HC16 without any external memory. The internal 1K RAM * is put into bank $0F to maintain 68HC11 code compatibility. This program was written with software * provided in the Motorola 68HC16 Evaluation Kit. * * Roger J.A. Chen, Applications Engineer * MAXIM Integrated Products * November 20, 1992 * ****************************************************************************************************************************************************** INCLUDE `EQUATES.ASM' ;Equates for common reg addrs INCLUDE `ORG00000.ASM' ;initialize reset vector INCLUDE `ORG00008.ASM' ;initialize interrupt vectors ORG $0200 ;start program after interrupt vectors INCLUDE `INITSYS.ASM' ;set EK=F,XK=0,YK=0,ZK=0 ;set sys clock at 16.78 MHz, COP off INCLUDE `INITRAM.ASM' ;turn on internal SRAM at $10000 ;set stack (SK=1, SP=03FE) MAIN: JSR INITQSPI MAINLOOP: JSR READ186 WAIT: LDAA SPSR ANDA #$80 BEQ WAIT ;wait for QSPI to finish BRA MAINLOOP ENDPROGRAM: INITQSPI: ;This routine sets up the QSPI microsequencer to operate on its own. ;The sequencer will read all eight channels of a MAX186/MAX188 each time ;it is triggered. The A/D converter results will be left in the ;receive data RAM. Each 16 bit receive data RAM location will ;have a leading zero, 12 bits of conversion result and three zeros. ; ;Receive RAM Bits 15 14 13 12 11 10 09 08 07 06 05 04 03 02 01 00 ;A/D Result 0 MSB LSB 0 0 0 ***** Initialize the QSPI Registers ****** PSHA PSHB LDAA #%01111000 STAA QPDR ;idle state for PCS0-3 = high LDAA #%01111011 STAA QPAR ;assign port D to be QSPI LDAA #%01111110 STAA QDDR ;only MISO is an input LDD #$8008 STD SPCR0 ;master mode,16 bits/transfer, ;CPOL=CPHA=0,1MHz Ser Clock LDD #$0000 STD SPCR1 ;set delay between PCS0 and SCK, Figure 20. MAX186/MAX188 Assembly-Code Listing Maxim Integrated 21 MAX186/MAX188 Low-Power, 8-Channel, Serial 12-Bit ADCs ;set delay between transfers LDD #$0800 STD SPCR2 ;set ENDQP to $8 for 9 transfers ***** Initialize QSPI Command RAM ***** LDAA #$80 ;CONT=1,BITSE=0,DT=0,DSCK=0,PCS0=ACTIVE STAA $FD40 ;store first byte in COMMAND RAM LDAA #$C0 ;CONT=1,BITSE=1,DT=0,DSCK=0,PCS0=ACTIVE STAA $FD41 STAA $FD42 STAA $FD43 STAA $FD44 STAA $FD45 STAA $FD46 STAA $FD47 LDAA #$40 ;CONT=0,BITSE=1,DT=0,DSCK=0,PCS0=ACTIVE STAA $FD48 ***** Initialize QSPI Transmit RAM ***** LDD #$008F LDD #$00CF LDD #$009F LDD #$00DF LDD #$00AF LDD #$00EF LDD #$00BF LDD #$00FF LDD #$0000 STD $FD20 STD $FD22 STD $FD24 STD $FD26 STD $FD28 STD $FD2A STD $FD2C STD $FD2E STD $FD30 PULB PULA RTS READ186: ;This routine triggers the QSPI microsequencer to autonomously ;trigger conversions on all 8 channels of the MAX186. Each ;conversion result is stored in the receive data RAM. PSHA LDAA #$80 ORAA SPCR1 STAA SPCR1 ;just set SPE PULA RTS ***** Interrupts/Exceptions ***** BDM: BGND ;exception vectors point here ;and put the user in background debug mode Figure 20. MAX186/MAX188 Assembly-Code Listing (continued) 22 Maxim Integrated MAX186/MAX188 Low-Power, 8-Channel, Serial 12-Bit ADCs CS **** **** SCLK **** SSTRB DIN **** Figure 21. QSPI Assembly-Code Timing TMS320C3x to MAX186 Interface Figure 22 shows an application circuit to interface the MAX186/MAX188 to the TMS320 in external clock mode. The timing diagram for this interface circuit is shown in Figure 23. Use the following steps to initiate a conversion in the MAX186/MAX188 and to read the results: 1) The TMS320 should be configured with CLKX (transmit clock) as an active-high output clock and CLKR (TMS320 receive clock) as an active-high input clock. CLKX and CLKR of the TMS320 are connected together with the SCLK input of the MAX186/MAX188. XF CLKX CS SCLK TMS320C3x MAX186 MAX188 CLKR DX DIN DR DOUT FSR SSTRB 2) The MAX186/MAX188 CS is driven low by the XF_ I/O port of the TMS320 to enable data to be clocked into DIN of the MAX186/MAX188. 3) An 8-bit word (1XXXXX11) should be written to the MAX186/MAX188 to initiate a conversion and place the device into external clock mode. Refer to Table 2 to select the proper XXXXX bit values for your specific application. 4) The SSTRB output of the MAX186/MAX188 is monitored via the FSR input of the TMS320. A falling edge on the SSTRB output indicates that the conversion is in progress and data is ready to be received from the MAX186/MAX188. Maxim Integrated Figure 22. MAX186/MAX188 to TMS320 Serial Interface 5) The TMS320 reads in one data bit on each of the next 16 rising edges of SCLK. These data bits represent the 12-bit conversion result followed by four trailing bits, which should be ignored. 6) Pull CS high to disable the MAX186/MAX188 until the next conversion is initiated. 23 MAX186/MAX188 Low-Power, 8-Channel, Serial 12-Bit ADCs CS SCLK DIN START SEL2 SEL1 SEL0 UNI/BIP SGL/DIF PD1 PD0 HIGH IMPEDANCE SSTRB DOUT MSB B10 B1 HIGH IMPEDANCE LSB Figure 23. TMS320 Serial Interface Timing Diagram __________Typical Operating Circuit _Ordering Information (continued) PART +5V CH0 0V to 4.096V ANALOG INPUTS DGND AGND CH7 MAX186 C1 4.7F C2 0.01F C4 0.1F CPU I/O SCLK SCK (SK)* DIN MOSI (SO) DOUT REFADJ C3 0.1F VSS CS VREF VDD VDD MISO (SI) SSTRB SHDN VSS 20 PDIP MAX188_CWP+ 0C to +70C 20 SO MAX188_CAP+ 0C to +70C 20 SSOP MAX188DC/D 0C to +70C Dice* MAX188_EPP+ -40C to +85C 20 PDIP MAX188_EWP+ -40C to +85C 20 SO MAX188_EAP+ -40C to +85C 20 SSOP PART MAX186EVKIT-DIP TEMP RANGE BOARD TYPE 0C to +70C Through-Hole Parts are offered in grades A, B, C and D (grades defined in Electrical Characteristics). When ordering, please specify grade. Contact factory for availability of A-grade in SSOP package. *Dice are specified at +25C, DC parameters only. +Denotes a lead(Pb)-free/RoHS-compliant package. Package Information For the latest package outline information and land patterns (footprints), go to www.maximintegrated.com/packages. Note that a "+", "#", or "-" in the package code indicates RoHS status only. Package drawings may show a different suffix character, but the drawing pertains to the package regardless of RoHS status. PACKAGE TYPE 24 PIN-PACKAGE 0C to +70C Chip Information Substrate connected to VDD TEMP RANGE MAX188_CPP+ PACKAGE CODE OUTLINE NO. LAND PATTERN NO. 20 PDIP P20+3 21-0043 -- 20 SO W20+3 21-0042 91-0108 20 SSOP A20+1 21-0056 91-0094 Maxim Integrated MAX186/MAX188 Low-Power, 8-Channel, Serial 12-Bit ADCs Revision History REVISION NUMBER REVISION DATE 0 3/93 Initial release 5 1/12 Updated the Ordering Information and Electrical Characteristics. DESCRIPTION PAGES CHANGED -- 1, 3, 18 Maxim Integrated cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim Integrated product. No circuit patent licenses are implied. Maxim Integrated reserves the right to change the circuitry and specifications without notice at any time. The parametric values (min and max limits) shown in the Electrical Characteristics table are guaranteed. Other parametric values quoted in this data sheet are provided for guidance. Maxim Integrated 160 Rio Robles, San Jose, CA 95134 USA 1-408-601-1000 (c) 2012 Maxim Integrated Products, Inc. 25 Maxim Integrated and the Maxim Integrated logo are trademarks of Maxim Integrated Products, Inc.