R03DS0029EJ0400 Rev.4.00 Page 1 of 12
Mar 16, 2011
The mark <R> shows major revised points.
The revised points can be easily searched by copying an "<R>" in the PDF file and specifying it in the "Find what:" field.
Preliminary Data Sheet
μ
PC2933A, 2905A
THREE-TERMINAL LOW DROPOUT VOLTAGE REGULATOR
Description
The
μ
PC2933A, 2905A of low dropout voltage three terminal positive regulators is constructed with PNP output
transistor. The
μ
PC2933A, 2905A feature the ability to source 1 A of output current with a low dropout voltage of typically
0.7 V.
The power dissipation of the
μ
PC2933A, 2905A can be drastically reduced compared with the conventional three
terminal positive voltage regulators that is constructed with NPN output transistor. Also, this series corresponds to the
low voltage output (3.3 V) which is not in the conventional low dropout regulators (
μ
PC24xxA series).
Features
• Output current in excess of 1.0 A
• Low dropout voltage
VDIF = 0.7 V TYP. (IO = 1 A)
• On-chip over-current and thermal protection circuit
• On-chip output transistor safe operating area protection circuit
Pin Configurations (Marking Side)
μ
PC2933AHF,
μ
PC2933AHB,
μ
PC2905AHF: Isolated TO-220 (MP-45G)
μ
PC2905AHB: SC-64 (MP-3)
μ
PC2933AT,
μ
PC2905AT: SC-63 (MP-3Z)
Notes 1. No.2 pin and No.4 fin are common GND.
2. No.2 pin is cut. No.2 pin and No.4 fin are common GND.
R03DS0029EJ0400
Rev.4.00
Mar 16, 2011
321
1: INPUT
2: GND
3: OUTPUT
4
321
1: INPUT
2: GND
3: OUTPUT
4: GND (Fin)
Note1
4
321
1: INPUT
2: GND
3: OUTPUT
4: GND (Fin)
Note2
μPC2933A,2905A Chapter Title
R03DS0029EJ0400 Rev.4.00 Page 2 of 12
Mar 16, 2011
Block Diagram
Start-up
circuit Reference
voltage
Thermal
shut down
Error
Amp. Drive
circuit
Saturation
protection
Safe operating
area protection
OUTPUT
GND
INPUT
Over-current
protection
Ordering Information
Part Number Package Output Voltage Marking
μ
PC2933AHF Isolated TO-220 (MP-45G) 3.3 V 2933A
μ
PC2933AHB SC-64 (MP-3) 3.3 V 2933A
μ
PC2933AT SC-63 (MP-3Z) 3.3 V 2933A
μ
PC2905AHF Isolated TO-220 (MP-45G) 5.0 V 2905A
μ
PC2905AHB SC-64 (MP-3) 5.0 V 2905A
μ
PC2905AT SC-63 (MP-3Z) 5.0 V 2905A
Remark Tape-packaged products have the symbol -E1, or -E2 suffixed to the part number. Pb-free products have the
symbol -AZ, or -AY suffixed to the part number. Refer to the following table for details.
Part Number Note1 Package Package Type
μ
PC29xxAHF-AZ Note2 Isolated TO-220 (MP-45G) • Packed in envelop
μ
PC29xxAHB-AZ Note2 SC-64 (MP-3) • Packed in envelop
μ
PC29xxAHB-AY Note3 SC-64 (MP-3) • Packed in envelop
μ
PC29xxAT-E1-AZ Note2 SC-63 (MP-3Z) • 16 mm wide embossed taping
• Pin 1 on draw-out side
• 2000 pcs/reel
μ
PC29xxAT-E1-AY Note3 SC-63 (MP-3Z) • 16 mm wide embossed taping
• Pin 1 on draw-out side
• 2000 pcs/reel
μ
PC29xxAT-E2-AZ Note2 SC-63 (MP-3Z) • 16 mm wide embossed taping
• Pin 1 at take-up side
• 2000 pcs/reel
μ
PC29xxAT-E2-AY Note3 SC-63 (MP-3Z) • 16 mm wide embossed taping
• Pin 1 at take-up side
• 2000 pcs/reel
Notes 1. xx stands for symbols that indicate the output voltage.
2. Pb-free (This product does not contain Pb in the external electrode.)
3. Pb-free (This product does not contain Pb in the external electrode, Sn100% plating.)
<R>
μPC2933A,2905A Chapter Title
R03DS0029EJ0400 Rev.4.00 Page 3 of 12
Mar 16, 2011
Absolute Maximum Ratings (TA = 25°C)
Rating Parameter
Symbol
μ
PC2933AHF, 2905AHF
μ
PC2933AHB, 2905AHB
μ
PC2933AT, 2905AT
Unit
Input Voltage VIN 20 V
Internal Power Dissipation (TC = 25°C) Note PT 15 10 W
Operating Ambient Temperature TA −30 to +85 °C
Operating Junction Temperature TJ −30 to +150 °C
Storage Temperature Tstg −55 to +150 °C
Thermal Resistance (junction to case) Rth(J-C) 7 12.5 °C/W
Thermal Resistance (junction to ambient) Rth(J-A) 65 125 °C/W
Note Internally limited. When the operating junction temperature rises above 150°C, the internal circuit shuts down the
output voltage.
Caution Product quality may suffer if the absolute maximum rating is exceeded even momentarily for any
parameter. That is, the absolute maximum ratings are rated values at which the product is on the
verge of suffering physical damage, and therefore the product must be used under conditions that
ensure that the absolute maximum ratings are not exceeded.
Typical Connection
INPUT
C
IN
PC2933A, 2905A OUTPUT
C
OUT
D
1
D
2
μ
+
CIN : 0.1
μ
F or higher. Be sure to connect CIN to prevent parasitic oscillation. Set this value according to the length
of the line between the regulator and the INPUT pin. Use of a film capacitor or other capacitor with first-rate
voltage and temperature characteristics is recommended. If using a laminated ceramic capacitor, it is
necessary to ensure that CIN is 0.1
μ
F or higher for the voltage and temperature range to be used.
COUT : 47
μ
F or higher. Be sure to connect COUT to prevent oscillation and improve excessive load regulation. Place
CIN and COUT as close as possible to the IC pins (within 1 to 2 cm). Also, use an electrolytic capacitor with low
impedance characteristics if considering use at sub-zero temperatures.
D1 : If the OUTPUT pin has a higher voltage than the INPUT pin, connect a diode.
D2 : If the OUTPUT pin has a lower voltage than the GND pin, connect a Schottky barrier diode.
Caution Make sure that no voltage is applied to the OUTPUT pin from external.
μPC2933A,2905A Chapter Title
R03DS0029EJ0400 Rev.4.00 Page 4 of 12
Mar 16, 2011
Recommended Conditions
Parameter Symbol Type Number MIN. TYP. MAX. Unit
μ
PC2933A 4.3 16 Input Voltage VIN
μ
PC2905A 6 16
V
Output Current IO All 0 1.0 A
Operating Ambient Temperature TA All −30 +85 °C
Operating Junction Temperature TJ All −30 +125 °C
Electrical Characteristics
μ
PC2933A (TJ = 25°C, VIN = 5 V, IO = 500 mA, CIN = 0.22
μ
F, COUT = 47
μ
F, unless otherwise specified)
Parameter Symbol Conditions MIN. TYP. MAX. Unit
3.18 3.3 3.42 Output Voltage VO
0°C ≤ TJ ≤ 125°C, 4.3 V ≤ VIN ≤ 16 V,
0 A ≤ IO ≤ 500 mA
0°C ≤ TJ ≤ 125°C, 0 A ≤ IO ≤ 1 A
3.14
3.46
V
Line Regulation REGIN 4.3 V ≤ VIN ≤ 16 V 12 33 mV
Load Regulation REGL 0 A ≤ IO ≤ 1 A 23 33 mV
IO = 0 A 2.0 3.0 Quiescent Current IBIAS
IO = 1 A 20 40
mA
VIN = 3.1 V, IO = 0 A 10 30 Startup Quiescent Current IBIAS (s)
VIN = 3.1 V, IO = 1 A 50
mA
Quiescent Current Change
Δ
IBIAS 0°C ≤ TJ ≤ 125°C, 4.3 V ≤ VIN ≤ 16 V 3.0 15 mA
Output Noise Voltage Vn 10 Hz ≤ f ≤ 100 kHz 55
μ
Vr.m.s.
Ripple Rejection R•R f = 120 Hz, 4.3 V ≤ VIN ≤ 16 V 48 64 dB
Dropout Voltage VDIF 0°C ≤ TJ ≤ 125°C, IO = 1 A 0.7 1.0 V
VIN = 4.5 V 1.2 1.6 3.0 Short Circuit Current IOshort
VIN = 16 V 1.2
A
VIN = 4.5 V 1.0 1.4 3.0 Peak Output Current IOpeak
VIN = 16 V 1.3 1.7 2.8
A
Temperature Coefficient of
Output Voltage
Δ
VO/
Δ
T 0°C ≤ TJ ≤ 125°C, IO = 5 mA −0.4 mV/°C
<R>
μPC2933A,2905A Chapter Title
R03DS0029EJ0400 Rev.4.00 Page 5 of 12
Mar 16, 2011
μ
PC2905A (TJ = 25°C, VIN = 8 V, IO = 500 mA, CIN = 0.22
μ
F, COUT = 47
μ
F, unless otherwise specified)
Parameter Symbol Conditions MIN. TYP. MAX. Unit
4.83 5.0 5.18 Output Voltage VO
0°C ≤ TJ ≤ 125°C, 6 V ≤ VIN ≤ 16 V,
0 A ≤ IO ≤ 500 mA
0°C ≤ TJ ≤ 125°C, 0 A ≤ IO ≤ 1 A
4.75
5.25
V
Line Regulation REGIN 6 V ≤ VIN ≤ 16 V 23 50 mV
Load Regulation REGL 0 A ≤ IO ≤ 1 A 28 50 mV
IO = 0 A 2.2 3.5 Quiescent Current IBIAS
IO = 1 A 28 50
mA
VIN = 4.5 V, IO = 0 A 10 30 Startup Quiescent Current IBIAS (s)
VIN = 4.5 V, IO = 1 A 50
mA
Quiescent Current Change
Δ
IBIAS 0°C ≤ TJ ≤ 125°C, 6 V ≤ VIN ≤ 16 V 2.9 15 mA
Output Noise Voltage Vn 10 Hz ≤ f ≤ 100 kHz 90
μ
Vr.m.s.
Ripple Rejection R•R f = 120 Hz, 6 V ≤ VIN ≤ 16 V 46 61 dB
Dropout Voltage VDIF 0°C ≤ TJ ≤ 125°C, IO = 1 A 0.7 1.0 V
VIN = 6.5 V 1.15 1.8 3.0 Short Circuit Current IOshort
VIN = 16 V 1.1
A
VIN = 6.5 V 1.1 1.5 3.0 Peak Output Current IOpeak
VIN = 16 V 1.4 2.0 2.8
A
Temperature Coefficient of
Output Voltage
Δ
VO/
Δ
T 0°C ≤ TJ ≤ 125°C, IO = 5 mA 0.6 mV/°C
μPC2933A,2905A Chapter Title
R03DS0029EJ0400 Rev.4.00 Page 6 of 12
Mar 16, 2011
Typical Characteristics
50 85 100 150
5
10
15
20
0
1.0
1.92
P
d -
Total Power Dissipation - W
T
A -
Operating Ambient Temperature - ˚C
0
P
d vs.
T
A
Solid line :
PC2933AHF, 2905AHF
Broken line :
PC2933AHB, 2905AHB
PC2933AT, 2905AT
With infinite heatsink
Without heatsink
300
200
100
0
-100
-200
-300
-400
0 100 150
T
J
Δ
V - Output Voltage Change - mV
O
Δ
V
O
vs. T
J
-50 50
PC2905A
PC2933A
I
O
= 5 mA
- Operating Junction Temperature -
˚C
μ
μ
4.0
3.5
3.0
2.5
2.0
1.5
1.0
0.5
0
012345678
V
IN
Voltage - V
V
O
- Output Voltage - V
V
O
vs.V
IN
PC2933A
T
J
= 25
˚C
O
= 0.5 A
I
O
= 5 mA
I
O
= 1.0 A
- Input
8
7
6
5
4
3
2
1
0
012345678
V
IN
-
Input
Voltage - V
V
O
vs. V
IN
PC2905A
T
J
= 25
˚C
O
= 0.5 A
I
O
= 5 mA
I
O
= 1.0 A
V
O
- Output Voltage - V
50
40
30
20
10
0
40 2 6 8 101214161820
BIAS Quiescent Current - mA
BIAS
I
BIAS(s)
) vs.V
IN
PC2933A
O
= 0.5 A
I
O
= 0 A
I
O
= 1 A
T = 25
˚C
V
IN -
Input
Voltage - V
50
40
30
20
10
0 2468101214161820
T = 25
˚C
O
= 0.5 A
I
O
= 0 A
I
O
= 1 A
V
IN -
Input
Voltage - V
BIAS
I
BIAS(s)
) vs.V
IN
PC2905A
BIAS
Quiescent Current - mA
μPC2933A,2905A Chapter Title
R03DS0029EJ0400 Rev.4.00 Page 7 of 12
Mar 16, 2011
1.0
0.8
0.6
0.4
0.2
0
-25 +1250 +150+75
V
DIF
- Dropout Voltage - V
V
DIF
vs.T
J
+100+50+25
PC2905A
PC2933A
I
O
= 1.0 A
T
J
Operating Junction Temperature -
˚C
3
2
1
0
0
20
DIF
IO peak - Peak Output Current - A
I
O peak
vs. V
DIF
PC2933A
10 155
T
J
= 125
˚C
T
J
= 25
˚C
T
J
= 0
˚C
- Dropout Voltage - V
V
μ
3
2
1
0
0
20
IO peak - Peak Output Current - A
vs.V
IO peak DIF
PC2905A
10 15
T
J
= 125
˚C
T
J
= 25
˚C
T
J
= 0
˚C
V
DIF - Dropout Voltage - V
R R vs. f
R R - Ripple Rejection - dB
80
70
0100 1 k 10 k 100 k
f - Frequency - Hz
60
50
40
30
20
10
T
J
= 25
˚C
I
O
= 1 A
PC2933A
PC2905A
4.3 V V
IN
16 V
6 V V
IN
16 V ( PC2905A)
( PC2933A)
R R vs. I
O
80
70
30
0.2 0.4 0.6 1.0
0.80
60
50
40
PC2933A
PC2905A
O
- Output Current - A
I
RR - Ripple Rejection - dB
f = 120 Hz
T
J
= 25
˚C
4.3 V V
IN
16 V
6 V V
IN
16 V ( PC2905A)
( PC2933A)
V
DIF
vs. IO
V
DIF - Dropout Voltage - V
1.0
00.2 0.4 0.6 1.0
IO - Output Current - A
0.8
0.6
0.4
0.2
00.8
PC2905A
PC2933A
T
J
= 25
˚C
μPC2933A,2905A Chapter Title
R03DS0029EJ0400 Rev.4.00 Page 8 of 12
Mar 16, 2011
V
O
vs.I
O
PC2933A
6
5
0 0.4 0.8 1.2 2.4
1.6
4
3
1
2.0
2
V
IN
= 16 V
V
IN
= 4.3 V
V
IN
= 5 V
T
J
= 25
˚C
IO - Output Current - A
V
O
- Output Voltage - V
6
5
0 0.4 0.8 1.2 2.4
1.6
4
3
1
2.0
2V
IN
= 16 V
V
IN
= 6 V
V
IN
= 8 V
V
O
vs.I
O
PC2905A
V
O - Output Voltage - V
I
O
- Output Current - A
T
J
= 25
˚C
μPC2933A,2905A Chapter Title
R03DS0029EJ0400 Rev.4.00 Page 9 of 12
Mar 16, 2011
Package Drawings (Unit: mm)
μ
PC2933AHF,
μ
PC2905AHF
D 17.0±0.3
3PIN PLASTIC SIP (MP-45G)
NOTE
Each lead centerline is located within 0.25 mm of
its true position (T.P.) at maximum material condition.
ITEM MILLIMETERS
P3HF-254B-4
G 0.25
H 2.54 (T.P.)
A 10.0±0.2
I 5.0±0.3
U 2.4±0.5
V
Y 8.9±0.7
Z 1.30±0.2
J
K
L 8.5±0.2
B 7.0±0.2
C 1.50±0.2
E
F 0.75±0.10
M 8.5±0.2
N
P 2.8±0.2
3.3±0.2
φ
2.46±0.2
5.0±0.2
4.5±0.2
0.65±0.10
132
M
A
B
E
I
D
L
M
K
Y
J
H
C
FG
Z
N
P
U
V
μPC2933A,2905A Chapter Title
R03DS0029EJ0400 Rev.4.00 Page 10 of 12
Mar 16, 2011
μ
PC2933AHB,
μ
PC2905AHB
SC-64 (MP-3) (Unit: mm)
123
4
2.32.3
0.75
1.1
±
0.1
0.5
1.6
±
0.2
5.0
±
0.2
6.5
±
0.2
5.5
±
0.27.0 MIN.
+0.2
−0.1
1.5+0.2
−0.1
13.7 MIN.
2.3
±
0.2
0.5
±
0.1
0.5+0.2
−0.1
μ
PC2933AT,
μ
PC2905AT
SC-63 (MP-3Z) (Unit: mm)
123
4
6.5±0.2
4.4±0.2
5.0±0.2
0.5±0.1
0.5±0.1
2.3±0.3 2.3±0.3
5.6±0.3
9.5±0.5
2.5±0.5
1.0±0.5
5.5±0.2
1.5+0.2
2.3±0.2
0.5±0.1
Note Note
0.4 MIN.
0.5 TYP.
0.15±0.15
−0.1
Note The depth of notch at the top of the fin is from 0 to 0.2 mm.
μPC2933A,2905A Chapter Title
R03DS0029EJ0400 Rev.4.00 Page 11 of 12
Mar 16, 2011
RECOMMENDED SOLDERING CONDITIONS
The
μ
PC2933A, 2905A should be soldered and mounted under the following recommended conditions.
For soldering methods and conditions other than those recommended below, contact your nearby sales representative.
For technical information, see the following website.
Semiconductor Device Mount Manual (http://www.renesas.com/prod/package/manual/)
Surface Mount Device
μ
PC29xxAT-AZ Series Note1,
μ
PC29xxAT-AY Series Note2: SC-63 (MP-3Z)
Process Conditions Symbol
Infrared Ray Reflow Peak temperature: 260°C or below (Package surface temperature),
Reflow time: 60 seconds or less (at 220°C or higher),
Maximum number of reflow processes: 3 times or less.
IR60-00-3
Partial Heating Method Pin temperature: 350°C or below,
Heat time: 3 seconds or less (Per each side of the device).
P350
Notes 1. Pb-free (This product does not contain Pb in the external electrode.)
2. Pb-free (This product does not contain Pb in the external electrode, Sn100% plating.)
Caution Apply only one kind of soldering condition to a device, except for "partial heating method", or the
device will be damaged by heat stress.
Remark Flux: Rosin-based flux with low chlorine content (chlorine 0.2 Wt% or below) is recommended.
Through-hole devices
μ
PC29xxAHF-AZ Series Note1: Isolated TO-220 (MP-45G)
μ
PC29xxAHB-AZ Series Note1,
μ
PC29xxAHB-AY Series Note2: SC-64 (MP-3)
Process Conditions Symbol
Wave soldering
(only to leads)
Solder temperature: 260°C or below, Flow time: 10 seconds or less. WS60-00-1
Partial heating method Pin temperature: 350°C or below, Heat time: 3 seconds or less (Per each pin). P350
Notes 1. Pb-free (This product does not contain Pb in the external electrode.)
2. Pb-free (This product does not contain Pb in the external electrode, Sn100% plating.)
Caution For through-hole device, the wave soldering process must be applied only to leads, and make sure that
the package body does not get jet soldered.
<R>
μPC2933A,2905A Chapter Title
R03DS0029EJ0400 Rev.4.00 Page 12 of 12
Mar 16, 2011
Notes On Use
When the
μ
PC2933A, 2905A are used with an input voltage that is lower than the value indicated in the recommended
operating conditions, a high quiescent current flows through the device due to saturation of the transistor of the output
stage. (Refer to the “IBIAS (IBIAS(S)) vs. VIN curves in Typical Characteristics”).
These products have saturation protector, but a current of up to 80 mA MAX. may flow through the device. Thus the
power supply on the input side must have sufficient capacity to allow this quiescent current to pass when the device
starts up.
Reference Documents
USER’S MANUAL USAGE OF THREE TERMINAL REGULATORS Document No.G12702E Note
REVIEW OF QUALITY AND RELIABILITY HANDBOOK Document No.C12769E Note
INFORMATION VOLTAGE REGULATOR OF SMD Document No.G11872E Note
SEMICONDUCTOR DEVICE PACKAGE MANUAL
http://www.renesas.com/prod/package/index.html
Note Published by the former NEC Electronics Corporation.
All trademarks and registered trademarks are the property of their respective owners.
C - 1
Revision History μPC2933A,2905A Data Sheet
Description
Rev. Date Page Summary
− Aug 2007 − Previous No. : G15374EJ3V0DS00
4.00 Mar 16, 2011 Throughout Deletion of leaded products
p.4 μPC2933A Startup Quiescent Current IBIAS (s) 80 mA -> 50 mA @VIN = 3.1 V, IO = 1 A
Notice
1. All information included in this document is current as of the date this document is issued. Such information, however, is subject to change without any prior notice. Before purchasing or using any Renesas
Electronics products listed herein, please confirm the latest product information with a Renesas Electronics sales office. Also, please pay regular and careful attention to additional and different information to
be disclosed by Renesas Electronics such as that disclosed through our website.
2. Renesas Electronics does not assume any liability for infringement of patents, copyrights, or other intellectual property rights of third parties by or arising from the use of Renesas Electronics products or
technical information described in this document. No license, express, implied or otherwise, is granted hereby under any patents, copyrights or other intellectual property rights of Renesas Electronics or
others.
3. You should not alter, modify, copy, or otherwise misappropriate any Renesas Electronics product, whether in whole or in part.
4. Descriptions of circuits, software and other related information in this document are provided only to illustrate the operation of semiconductor products and application examples. You are fully responsible for
the incorporation of these circuits, software, and information in the design of your equipment. Renesas Electronics assumes no responsibility for any losses incurred by you or third parties arising from the
use of these circuits, software, or information.
5. When exporting the products or technology described in this document, you should comply with the applicable export control laws and regulations and follow the procedures required by such laws and
regulations. You should not use Renesas Electronics products or the technology described in this document for any purpose relating to military applications or use by the military, including but not limited to
the development of weapons of mass destruction. Renesas Electronics products and technology may not be used for or incorporated into any products or systems whose manufacture, use, or sale is
prohibited under any applicable domestic or foreign laws or regulations.
6. Renesas Electronics has used reasonable care in preparing the information included in this document, but Renesas Electronics does not warrant that such information is error free. Renesas Electronics
assumes no liability whatsoever for any damages incurred by you resulting from errors in or omissions from the information included herein.
7. Renesas Electronics products are classified according to the following three quality grades: "Standard", "High Quality", and "Specific". The recommended applications for each Renesas Electronics product
depends on the product's quality grade, as indicated below. You must check the quality grade of each Renesas Electronics product before using it in a particular application. You may not use any Renesas
Electronics product for any application categorized as "Specific" without the prior written consent of Renesas Electronics. Further, you may not use any Renesas Electronics product for any application for
which it is not intended without the prior written consent of Renesas Electronics. Renesas Electronics shall not be in any way liable for any damages or losses incurred by you or third parties arising from the
use of any Renesas Electronics product for an application categorized as "Specific" or for which the product is not intended where you have failed to obtain the prior written consent of Renesas Electronics.
The quality grade of each Renesas Electronics product is "Standard" unless otherwise expressly specified in a Renesas Electronics data sheets or data books, etc.
"Standard": Computers; office equipment; communications equipment; test and measurement equipment; audio and visual equipment; home electronic appliances; machine tools;
personal electronic equipment; and industrial robots.
"High Quality": Transportation equipment (automobiles, trains, ships, etc.); traffic control systems; anti-disaster systems; anti-crime systems; safety equipment; and medical equipment not specifically
designed for life support.
"Specific": Aircraft; aerospace equipment; submersible repeaters; nuclear reactor control systems; medical equipment or systems for life support (e.g. artificial life support devices or systems), surgical
implantations, or healthcare intervention (e.g. excision, etc.), and any other applications or purposes that pose a direct threat to human life.
8. You should use the Renesas Electronics products described in this document within the range specified by Renesas Electronics, especially with respect to the maximum rating, operating supply voltage
range, movement power voltage range, heat radiation characteristics, installation and other product characteristics. Renesas Electronics shall have no liability for malfunctions or damages arising out of the
use of Renesas Electronics products beyond such specified ranges.
9. Although Renesas Electronics endeavors to improve the quality and reliability of its products, semiconductor products have specific characteristics such as the occurrence of failure at a certain rate and
malfunctions under certain use conditions. Further, Renesas Electronics products are not subject to radiation resistance design. Please be sure to implement safety measures to guard them against the
possibility of physical injury, and injury or damage caused by fire in the event of the failure of a Renesas Electronics product, such as safety design for hardware and software including but not limited to
redundancy, fire control and malfunction prevention, appropriate treatment for aging degradation or any other appropriate measures. Because the evaluation of microcomputer software alone is very difficult,
please evaluate the safety of the final products or system manufactured by you.
10. Please contact a Renesas Electronics sales office for details as to environmental matters such as the environmental compatibility of each Renesas Electronics product. Please use Renesas Electronics
products in compliance with all applicable laws and regulations that regulate the inclusion or use of controlled substances, including without limitation, the EU RoHS Directive. Renesas Electronics assumes
no liability for damages or losses occurring as a result of your noncompliance with applicable laws and regulations.
11. This document may not be reproduced or duplicated, in any form, in whole or in part, without prior written consent of Renesas Electronics.
12. Please contact a Renesas Electronics sales office if you have any questions regarding the information contained in this document or Renesas Electronics products, or if you have any other inquiries.
(Note 1) "Renesas Electronics" as used in this document means Renesas Electronics Corporation and also includes its majority-owned subsidiaries.
(Note 2) "Renesas Electronics product(s)" means any product developed or manufactured by or for Renesas Electronics.
http://www.renesas.com
Refer to "http://www.renesas.com/" for the latest and detailed information.
Renesas Electronics America Inc.
2880 Scott Boulevard Santa Clara, CA 95050-2554, U.S.A.
Tel: +1-408-588-6000, Fax: +1-408-588-6130
Renesas Electronics Canada Limited
1101 Nicholson Road, Newmarket, Ontario L3Y 9C3, Canada
Tel: +1-905-898-5441, Fax: +1-905-898-3220
Renesas Electronics Europe Limited
Dukes Meadow, Millboard Road, Bourne End, Buckinghamshire, SL8 5FH, U.K
Tel: +44-1628-585-100, Fax: +44-1628-585-900
Renesas Electronics Europe GmbH
Arcadiastrasse 10, 40472 Düsseldorf, Germany
Tel: +49-211-65030, Fax: +49-211-6503-1327
Renesas Electronics (China) Co., Ltd.
7th Floor, Quantum Plaza, No.27 ZhiChunLu Haidian District, Beijing 100083, P.R.China
Tel: +86-10-8235-1155, Fax: +86-10-8235-7679
Renesas Electronics (Shanghai) Co., Ltd.
Unit 204, 205, AZIA Center, No.1233 Lujiazui Ring Rd., Pudong District, Shanghai 200120, China
Tel: +86-21-5877-1818, Fax: +86-21-6887-7858 / -7898
Renesas Electronics Hong Kong Limited
Unit 1601-1613, 16/F., Tower 2, Grand Century Place, 193 Prince Edward Road West, Mongkok, Kowloon, Hong Kong
Tel: +852-2886-9318, Fax: +852 2886-9022/9044
Renesas Electronics Taiwan Co., Ltd.
7F, No. 363 Fu Shing North Road Taipei, Taiwan
Tel: +886-2-8175-9600, Fax: +886 2-8175-9670
Renesas Electronics Singapore Pte. Ltd.
1 harbourFront Avenue, #06-10, keppel Bay Tower, Singapore 098632
Tel: +65-6213-0200, Fax: +65-6278-8001
Renesas Electronics Malaysia Sdn.Bhd.
Unit 906, Block B, Menara Amcorp, Amcorp Trade Centre, No. 18, Jln Persiaran Barat, 46050 Petaling Jaya, Selangor Darul Ehsan, Malaysia
Tel: +60-3-7955-9390, Fax: +60-3-7955-9510
Renesas Electronics Korea Co., Ltd.
11F., Samik Lavied' or Bldg., 720-2 Yeoksam-Dong, Kangnam-Ku, Seoul 135-080, Korea
Tel: +82-2-558-3737, Fax: +82-2-558-5141
SALES OFFICES
© 2011 Renesas Electronics Corporation. All rights reserved.
Colophon 1.0
