MCT 0603, MCU 0805, MCA 1206 - Precision Vishay Beyschlag Precision Flat Chip Resistors FEATURES * Approved according to EN 140401-801 * Thin-film technology Low TC: 10 to 25 ppm/K Precision tolerance of value: 0.1 and 0.25 % Superior overall stability: class 0.1 and 0.25 Green product, supports lead-free soldering * * * * APPLICATIONS * Test and measuring equipment * Medical equipment * Industrial equipment. MCT 0603, MCU 0805 and MCA 1206 Precision Thin Film Flat Chip Resistors combine the proven reliability of the professional products with an advanced level of precision and stability. Therefore they are perfectly suited for applications in the fields of test and measuring equipment together with industrial and medical electronics. METRIC SIZE INCH: METRIC: 0603 0805 1206 RR 1608M RR 2012M RR 3216M TECHNICAL SPECIFICATIONS DESCRIPTION MCT 0603 Metric size Resistance range MCA 1206 RR 1608M RR 2012M RR 3216M 47 to 150 k 47 to 332 k 47 to 332 k Resistance tolerance Temperature coefficient Operation mode MCU 0805 0.25 %; 0.1 % 0.1 % 25 ppm/K; 15 ppm/K; 10 ppm/K 25 ppm/K precision standard precision standard precision standard 10/85/56 55/125/56 10/85/56 55/125/56 10/85/56 55/125/56 0.032 W 0.1 W 0.050 W 0.125 W 0.1 W 0.25 W Operating voltage, Umax AC/DC 25 V 75 V 35 V 150 V 50 V 200 V Film temperature 85 C 125 C 85 C 125 C 85 C 125 C Climatic category (LCT/UCT/days) Rated dissipation, P70 (1) Max. resistance change at P70 47 to 150 k 47 to 332 k 47 to 332 k 1 000 h 0.1 % 0.2 % 0.1 % 0.2 % 0.05 % 0.1 % 8 000 h 0.2 % 0.4 % 0.2 % 0.4 % 0.1 % 0.25 % 225 000 h 0.5 % 1.0 % 0.5 % 1.0 % 0.25 % 0.5 % Specified lifetime 225 000 h 225 000 h 225 000 h 1 minute; Uins 100 V 200 V 300 V continuous 75 V 75 V 75 V Insulation voltage : Failure rate 2x 10-9/h 2x 10-9/h 2 x 10-9/h Note 1. The power dissipation on the resistor generates a temperature rise against the local ambient, depending on the heat flow support of the printed-circuit board (thermal resistance). The rated dissipation applies only if the permitted film temperature is not exceeded. Document Number: 28700 Revision: 13-May-04 For technical questions contact: ff3aresistors@vishay.com www.vishay.com 1 MCT 0603, MCU 0805, MCA 1206 - Precision Precision Flat Chip Resistors Vishay Beyschlag ORDERING INFORMATION - type description and ordering code M C FILM TYPE T 0603 -25 0.1 % PRODUCT CODE SIZE CODE IMPERIAL SIZE TEMPERATURE TOLERANCE COEFFICIENT M = Metal film or cermet C = Flat chip T = 0603 U = 0805 A = 1206 0603 0805 1206 10 ppm/K 15 ppm/K 25 ppm/K 0.1 % 0.25 % P5 47 K PACKAGING RESISTANCE VALUE P1 = 1000 units See Temperature P5 = 5000 units coefficient and PW = 20000 resistance range table units Note: We recommend that the clear text ordering code is used to minimize the possibility of errors in order handling. DIMENSIONS T1 W WT H T2 L DIMENSIONS - CHIP resistor types, mass and relevant physical dimensions H (mm) L (mm) W (mm) WT (mm) T1 (mm) T2 (mm) MASS (mg) MCT 0603 0.45 + 0.1/- 0.05 1.55 0.05 0.85 0.1 > 75 % of W 0.3 + 0.15/- 0.2 0.3 + 0.15/- 0.2 1.9 MCU 0805 0.45 + 0.1/- 0.05 2.0 0.1 1.25 0.15 > 75 % of W 0.4 + 0.1/- 0.2 0.4 + 0.1/- 0.2 4.6 MCA 1206 0.55 0.1 3.2 + 0.1/- 0.2 1.6 0.15 > 75 % of W 0.5 0.25 0.5 0.25 9.2 TYPE TEMPERATURE COEFFICIENT AND RESISTANCE RANGE RESISTANCE VALUE (1) DESCRIPTION T.C. TOLERANCE MCT 0603 MCU 0805 MCA 1206 25 ppm/K 0.25 % 47 to 150 k 47 to 332 k - 0.1 % 100 to 150 k 47 to 332 k 47 to 332 k 15 ppm/K 10 ppm/K(2) 0.25 % 47 to 150 k 47 to 100 k - 0.1 % 100 to 100 k 100 to 100 k - 0.25 % 47 to 20 k 47 to 36 k - 0.1 % 100 to 20 k 100 to 36 k - Note 1. Resistance values to be selected from E96 and E192 series, other values are available on request. 2. TC 10 is specified over the temperature range from - 10 C to 85 C. Resistance ranges printed in bold are preferred T.C./tolerance combinations with optimized availability. www.vishay.com 2 For technical questions contact: ff3aresistors@vishay.com Document Number: 28700 Revision: 13-May-04 MCT 0603, MCU 0805, MCA 1206 - Precision Precision Flat Chip Resistors Vishay Beyschlag DESCRIPTION Production is strictly controlled and follows an extensive set This includes full compatibility with the following directives: of * 2000/53/EC End of Vehicle life Directive (ELV) instructions established for reproducibility. A homogeneous film of metal alloy is deposited on a super high * 2000/53/EC Annex II to End of Vehicle Life Directive (ELV II) grade (96 % Al203) ceramic substrate and conditioned to * 2002/95/EC Restriction of the use of Hazardous Substances Directive (RoHS) achieve the desired temperature coefficient. Specially designed inner contacts are deposited on both sides. A special laser is used to achieve the target value by smoothly fine trimming the resistive layer without damaging the ceramics. A further conditioning is applied in order to * 2002/96/EC Waste Electrical and Electronic Equipment Directive (WEEE) Solderability is specified for 2 years after production or re-qualification. The permitted storage time is 20 years. stabilize the trimming result. The resistor elements are covered by a blue protective coating designed for electrical, mechanical and climatic protection. The terminations receive a final pure tin on nickel plating. APPROVALS The resistors are tested in accordance with EN 140401-801 (superseding CECC 40401-801) which refers to EN 60115-1 The result of the determined production is verified by an and EN 140400. Approval of conformity is indicated by the extensive CECC logo on the package label. testing procedure and optical inspection performed on 100 % of the individual chip resistors. Only accepted products are laid directly into the paper tape in accordance with EN 60286-3. Vishay BEYSCHLAG has achieved "Approval of Manufacturer" in accordance with EN 100114-1. The release certificate for "Technology Approval Schedule" in accordance with CECC 240001 based on EN 100114-6 is ASSEMBLY granted for the Vishay BEYSCHLAG manufacturing process. The resistors are suitable for processing on automatic SMD assembly systems and for automatic soldering using wave, SPECIALS reflow or vapour phase. The encapsulation is resistant to all On request, resistors are available with established reliability cleaning solvents commonly used in the electronics industry, in accordance with EN 140 401-801 Version E. Please refer including alcohols, esters and aqueous solutions. The to the special data sheet for information on failure rate level, resistors are lead (Pb)-free, the pure tin plating provides available resistance ranges and order codes. compatibility with lead (Pb)-free and lead-containing soldering processes. The immunity of the plating against tin whisker growth has been proven under extensive testing. All products comply with the CEFIC-EECA-EICTA list of legal restrictions on hazardous substances. Document Number: 28700 Revision: 13-May-04 For technical questions contact: ff3aresistors@vishay.com www.vishay.com 3 MCT 0603, MCU 0805, MCA 1206 - Precision Precision Flat Chip Resistors Vishay Beyschlag Power Dissipation P FUNCTIONAL PERFORMANCE MCT 0603 MCU 0805 MCA 1206 0.2 W 0.1 0 0 -50 50 70 C 100 150 Ambient Temperature amb Power Dissipation P Derating - Standard Operation MCT 0603 MCU 0805 MCA 1206 0.2 W 0.1 0 0 -50 50 70 100 C 150 Ambient Temperature amb Current Noise A1 Derating - Precision Operation 1 V/V 0.1 MCT 0603 MCU 0805 MCA 1206 0.01 10 k 1 k 100 k 1 M 10 M Resistance Value R Current Noise A1 www.vishay.com 4 In accordance with IEC 60195 For technical questions contact: ff3aresistors@vishay.com Document Number: 28700 Revision: 13-May-04 MCT 0603, MCU 0805, MCA 1206 - Precision Precision Flat Chip Resistors Vishay Beyschlag TEST AND REQUIREMENTS All tests are carried out in accordance with the following specifications: EN 60115-1, Generic specification (includes tests) EN 140 400, Sectional specification (includes schedule for qualification approval) EN 140 401-801, Detail specification (includes schedule for conformance inspection) The components are approved in accordance with the European CECC-system, where applicable. The following table contains only the most important tests. For the full test schedule refer to the documents listed above. The testing also covers most of the requirements specified by EIA/IS-703 and JIS-C-5202. The tests are carried out in accordance with IEC 60068 and under standard atmospheric conditions in accordance with IEC 60068-1, 5.3. Climatic category LCT/UCT/56 (rated temperature range: Lower Category Temperature, Upper Category Temperature; damp heat, long term, 56 days) is valid. Unless otherwise specified the following values apply: Temperature: 15 C to 35 C Relative humidity: 45 % to 75 % Air pressure: 86 kPa to 106 kPa (860 mbar to 1 060 mbar). The components are mounted for testing on boards in accordance with EN 60115-1, 4.31 unless otherwise specified. The parameters stated in the Test Procedures and Requirements table are based on the required tests and permitted limits of EN 140 401-801. However, some additional tests and a number of improvements against those minimum requirements have been included. TEST PROCEDURES AND REQUIREMENTS EN 60115-1 CLAUSE IEC 60068-2 TEST METHOD TEST PROCEDURE REQUIREMENTS PERMISSIBLE CHANGE STABILITY CLASS 0.1 STABILITY CLASS 0.25 MCT 0603 100 to 10 k 47 to < 100 ; > 10 k to 150 k MCU 0805 100 to 47.5 k 47 to < 100 ; > 47.5 k to 332 k MCA 1206 47 to 332 k - stability for product types: 4.5 - resistance 4.8.4.2 - temperature coefficient at 20 / -10 / 20 C and 20 / 85 / 20 C 4.25.1 - endurance at 70 C: standard operation mode U= - Document Number: 28700 Revision: 13-May-04 endurance at 70 C: power operation mode 0.1 %; 0.25 % 25 ppm/K; 15 ppm/K; 10 ppm/K P 70 x R or U = Umax; whichever is the less severe; 1.5 h on; 0,5 h off 70 C; 1000 h (0.1 %R + 0.02 ) (1) 70 C; 8000 h (0.2 %R + 0.02 ) (1) U = P 70 x R or U = Umax; whichever is the less severe; 1.5 h on; 0.5 h off 1.5 h on; 0.5 h off 70 C; 1000 h (0.2 %R + 0.02 ) (1) 70 C; 8000 h (0.4 %R + 0.05 ) (1) For technical questions contact: ff3aresistors@vishay.com www.vishay.com 5 MCT 0603, MCU 0805, MCA 1206 - Precision Precision Flat Chip Resistors Vishay Beyschlag TEST PROCEDURES AND REQUIREMENTS - continued EN 60115-1 CLAUSE IEC 60068-2 TEST METHOD TEST PROCEDURE REQUIREMENTS PERMISSIBLE CHANGE STABILITY CLASS 0.1 STABILITY CLASS 0.25 MCT 0603 100 to 10 k 47 to < 100 ; > 10 k to 150 k MCU 0805 100 to 47.5 k 47 to < 100 ; > 47.5 k to 332 k MCA 1206 47 to 332 k - stability for product types: 4.25.3 - endurance at upper category temperature 85 C; 1000h 125 C; 1000h (0.1 %R + 0.02 ) (0.2 %R + 0.02 ) (0.2 %R + 0.02 ) (0.25 %R + 0.05 ) 4.24 78 (Cab) damp heat, steady state (40 2) C; 56 days; (93 3) % RH (0.1 %R + 0.02 ) (0.25 %R + 0.05 ) UCT; 16 h (0.1 %R + 0.02 ) (0.25 %R + 0.05 ) 4.23 4.23.2 2 (Ba) climatic sequence: dry heat 4.23.3 30 (Db) damp heat, cyclic 55 C; 24 h; > 90 % RH;1 cycle 4.23.4 1 (Aa) cold LCT; 2 h 4.23.5 13 (M) low air pressure 8.5 kPa; 2 h; 25 10 C 4.23.6 30 (Db) damp heat, cyclic 55 C; 5 days; > 95 to 100 % RH; 5 cycles LCT = - 55 C; UCT = 125 C - 1 (Aa) cold - 55 C; 2h (0.05 %R + 0.01 ) 4.19 14 (Na) rapid change of temperature 30 minutes at LCT and 30 minutes at UCT; LCT = - 10 C UCT = 85 C; 5 cycles LCT = -10C; UCT = 85C; 5 cycle (0.05 %R + 0.01 ) no visible damage LCT = - 55 C; UCT = 125 C; 1000 cycles (0.25 %R + 0.05 ) no visible damage 4.13 - short time overload; precision operation mode short time overload; standard operation mode 4.27 4.37 - - www.vishay.com 6 (0.05 %R + 0.01 ) U = 2.5 x P 70 x R or U = 2 x Umax; whichever is the less severe; 5s (0.05 %R + 0.01 ) single pulse high voltage overload; standard operation mode severity no. 4: U = 10 x P 70 x R or U = 2 x Umax; whichever is the less severe; 10 pulses 10s/700s (0.5 %R + 0.05 ) (2) periodic electric overload; standard operation mode U = 15 x P 70 x R or U = 2 x Umax; whichever is the less severe; 0.1 s on; 2.5 s off; 1000 cycles (0.5 %R + 0.05 ) (2) no visible damage no visible damage For technical questions contact: ff3aresistors@vishay.com Document Number: 28700 Revision: 13-May-04 MCT 0603, MCU 0805, MCA 1206 - Precision Precision Flat Chip Resistors Vishay Beyschlag TEST PROCEDURES AND REQUIREMENTS - continued EN 60115-1 CLAUSE IEC 60068-2 TEST METHOD TEST PROCEDURE REQUIREMENTS PERMISSIBLE CHANGE STABILITY CLASS 0.1 STABILITY CLASS 0.25 MCT 0603 100 to 10 k 47 to < 100 ; > 10 k to 150 k MCU 0805 100 to 47.5 k 47 to < 100 ; > 47.5 k to 332 k MCA 1206 47 to 332 k - stability for product types: 4.22 4.17.2 6 (Fc) 58 (Td) vibration endurance by sweeping; 10 to 2000 Hz; no resonance; amplitude 1.5 mm or 200 m/s2; 6 h solderability 4.18.2 58 (Td) resistance to soldering heat solder bath method; (260 5) C; (10 1) s 4.29 45 (XA) component solvent resistance isopropyl alcohol + 50 C; shear RR 1608M; 9 N RR 2012M and RR 3216; 45 N 21 (Ue3) 4.33 21 (Ue1) 4.7 4.35 - substrate bending voltage proof flammability no visible damage solder bath method; SnPb40; non-activated flux (215 3) C; (3 0.3) s solder bath method; SnAg3Cu0,5 or SnAg3,5; non-activated flux (235 3) C; (2 0.2) s 4.32 (0.05 %R + 0.01 ) good tinning ( 95 % covered); no visible damage (0.05 %R + 0.01 ) no visible damage method 2 depth 2 mm, 3 times Urms = Uins; 60 5 s IEC 60695-2-2, needle flame test; 10 s no visible damage (0.05 %R + 0.01 ) no visible damage, no open circuit in bent position no flashover or breakdown no burning after 30 s Special requirements for type MCA 1206 4.25.1 - - endurance at 70 C: precision operation mode endurance at 70 C: standard operation mode U = P 70 x R or U = Umax; whichever is the less severe 70 C; 1000 h 70 C; 8000 h U = P 70 x R or U = Umax; whichever is the less severe (0.05 %R + 0.02 ) (0.1 %R + 0.02 ) 70 C; 1000 h 70 C; 8000 h (0.1 %R + 0.02 ) (0.25 %R + 0.05 ) Notes 1. See 4.25.1 (above): special requirements for type MCA 1206. 2. The pulse load stability of professional MFC resistors applies for precision resistors also. However, severe pulse loads are likely to jeopardise precision stability requirements. Document Number: 28700 Revision: 13-May-04 For technical questions contact: ff3aresistors@vishay.com www.vishay.com 7 MCT 0603, MCU 0805, MCA 1206 - Precision Precision Flat Chip Resistors Vishay Beyschlag ORDERING INFORMATION Components may be ordered by using either a simple clear text ordering code, see "Type description and ordering code" or Vishay BCcomponents' unique 12NC. Last Digit of 12NC Indicating Resistance Decade Numeric Ordering Code (12NC) * The resistors have a 12-digit ordering code starting with 2312. * The subsequent 4 digits indicate the resistor type, specification and packaging; see the 12NC Ordering Code table. * The remaining 4 digits indicate the resistance value: RESISTANCE DECADE LAST DIGIT 10 to 99.9 9 100 to 999 1 1 k to 9.99 k 2 10 k to 99.9 k 3 100 k to 999 k 4 Ordering Example - The first 3 digits indicate the resistance value. The ordering code of a MCT 0603 resistor, value 47 k and - The last digit indicates the resistance decade in accordance with the 12NC Indicating Resistance Decade table. TC 25 with 0.1 % tolerance, supplied in cardboard tape of 5000 units per reel is: 2312 216 74703. 12NC ORDERING CODE - resistors type and packaging ORDERING CODE 2312... ..... DESCRIPTION CARDBOARD TAPE ON REEL TYPE T.C. TOL. P1 1 000 UNITS P5 5 000 UNITS PW 20 000 UNITS 0.25 % 201 6.... 216 6.... 206 6.... 0.1 % 201 7.... 216 7.... 206 7.... 0.25 % 202 6.... 217 6.... 207 6.... 0.1 % 202 7.... 217 7.... 207 7.... 0.25 % 203 6.... 218 6.... 208 6.... 0.1 % 203 7.... 218 7.... 208 7.... 0.25 % 241 6.... 256 6.... 246 6.... 0.1 % 241 7.... 256 7.... 246 7.... 0.25 % 242 6.... 257 6.... 247 6.... 0.1 % 242 7.... 257 7.... 247 7.... 0.25 % 243 6.... 258 6.... 248 6.... 0.1 % 243 7.... 258 7.... 248 7.... 0.1 % 381 7.... 396 7.... 386 7.... 25 ppm/K MCT 0603 15 ppm/K 10 ppm/K 25 ppm/K MCU 0805 15 ppm/K 10 ppm/K MCA 1206 25 ppm/K Resistance ranges printed in bold are preferred T.C./tolerance combinations with optimized availability. www.vishay.com 8 For technical questions contact: ff3aresistors@vishay.com Document Number: 28700 Revision: 13-May-04