LP2998 DDR-I and DDR-II Termination Regulator General Description Features The LP2998 linear regulator is designed to meet JEDEC SSTL-2 and JEDEC SSTL-18 specifications for termination of DDR1-SDRAM and DDR-II memory. The device contains a high-speed operational amplifier to provide excellent response to load transients. The output stage prevents shoot through while delivering 1.5A continuous current as required for DDR1-SDRAM termination, and 0.5A continuous current as required for DDR-II termination. The LP2998 also incorporates a VSENSE pin to provide superior load regulation and a VREF output as a reference for the chipset and DIMMs. An additional feature found on the LP2998 is an active low shutdown (SD) pin that provides Suspend To RAM (STR) functionality. When SD is pulled low, the VTT output will tristate providing a high impedance output, while VREF remains active. A power savings advantage can be obtained in this mode through lower quiescent current. Source and sink current Low output voltage offset No external resistors required Linear topology Suspend to Ram (STR) functionality Low external component count Thermal Shutdown Available in SO-8, PSOP-8 packages Applications DDR-I, DDR-II and DDR-III Termination Voltage SSTL-18 Termination SSTL-2 and SSTL-3 Termination HSTL Termination Typical Application Circuit 30026918 (c) 2012 Texas Instruments Incorporated 300269 SNVS521H www.ti.com LP2998 DDR-I and DDR-II Termination Regulator June 29, 2012 LP2998 Connection Diagrams 30026903 Top View PSOP-8 Layout 30026904 Top View SO-8 Layout Pin Descriptions SO-8 Pin or PSOP-8 Pin Name 1 GND Function Ground. 2 SD 3 VSENSE Shutdown. 4 VREF Buffered internal reference voltage of VDDQ /2. 5 VDDQ Input for internal reference equal to VDDQ/2. 6 AVIN Analog input pin. 7 PVIN Power input pin. 8 VTT Output voltage for connection to termination resistors. EP Exposed pad thermal connection. Connect to Ground (PSOP-8 only). Feedback pin for regulating VTT. Ordering Information Order Number Package Type NSC Package Drawing LP2998MA SO-8 M08A 95 Units per Rail LP2998MAX SO-8 M08A 2500 Units Tape and Reel LP2998MAE SO-8 M08A 250 Units Tape and Reel LP2998MR PSOP-8 MRA08A 95 Units per Rail LP2998MRX PSOP-8 MRA08A 2500 Units Tape and Reel LP2998MRE PSOP-8 MRA08A 250 Units Tape and Reel www.ti.com 2 Supplied As Operating Range If Military/Aerospace specified devices are required, please contact the Texas Instruments Sales Office/ Distributors for availability and specifications. Junction Temp. Range (Note 4) AVIN to GND AVIN to GND PVIN to GND VDDQ (Note 2) Storage Temp. Range Junction Temperature Lead Temperature (Soldering, 10 sec) -40C to +125C 2.2V to 5.5V -0.3V to +6V -0.3V to AVIN -0.3V to +6V -65C to +150C 150C 260C SO-8 Thermal Resistance (JA) 151C/W PSOP-8 Thermal Resistance (JA) Minimum ESD Rating (Note 3) 43C/W 1kV Electrical Characteristics Specifications with standard typeface are for TJ = 25C and limits in boldface type apply over the full Operating Temperature Range (TJ = -40C to +125C) (Note 5). Unless otherwise specified, VIN = AVIN = PVIN = 2.5V. Symbol Parameter Conditions Typ Max Units VIN = VDDQ = 2.3V VIN = VDDQ = 2.5V VIN = VDDQ = 2.7V 1.135 1.158 1.185 1.235 1.258 1.285 1.335 1.358 1.385 V V V VREF Voltage (DDR II) PVIN = VDDQ = 1.7V PVIN = VDDQ = 1.8V PVIN = VDDQ = 1.9V 0.837 0.860 0.887 0.887 0.910 0.937 0.936 0.959 0.986 V V V VREF Voltage (DDR III) PVIN = VDDQ = 1.35V PVIN = VDDQ = 1.5V PVIN = VDDQ = 1.6V 0.669 0.684 0.699 0.743 0.758 0.773 0.793 0.808 0.823 V V V VREF Output Impedance IREF = -30 to +30 A 2.5 k VREF ZVREF Min VREF Voltage (DDR I) 3 www.ti.com LP2998 Absolute Maximum Ratings (Note 1) LP2998 Symbol Parameter Conditions Min Typ Max Units IOUT = 0A VTT Output Voltage (DDR I) (Note 8) VIN = VDDQ = 2.3V VIN = VDDQ = 2.5V VIN = VDDQ = 2.7V IOUT = +/- 1.5A 1.120 1.159 1.190 1.210 1.259 1.290 1.320 1.359 1.390 V V V VIN = VDDQ = 2.3V VIN = VDDQ = 2.5V VIN = VDDQ = 2.7V 1.125 1.159 1.190 1.225 1.259 1.290 1.325 1.359 1.390 V V V PVIN = VDDQ = 1.7V 0.822 0.856 0.887 PVIN = VDDQ = 1.8V 0.874 0.908 0.939 PVIN = VDDQ = 1.9V 0.923 0.957 0.988 IOUT = +/- 0.5A, AVIN = 2.5V V V V IOUT = 0A, AVIN = 2.5V VTT Output Voltage (DDR II) (Note 8) PVIN = VDDQ = 1.7V PVIN = VDDQ = 1.8V PVIN = VDDQ = 1.9V VTT 0.820 0.856 0.890 0.870 0.908 0.940 0.920 0.957 0.990 V V V PVIN = VDDQ = 1.35V PVIN = VDDQ = 1.5V PVIN = VDDQ = 1.6V 0.656 0.677 0.698 0.731 0.752 0.773 0.781 0.802 0.823 V V V IOUT = +0.2A, AVIN = 2.5V PVIN = VDDQ = 1.35V IOUT = -0.2A, AVIN = 2.5V PVIN = VDDQ = 1.35V 0.667 0.688 0.710 V 0.641 0.673 0.694 V IOUT = +0.4A, AVIN = 2.5V PVIN = VDDQ = 1.5V IOUT = -0.4A, AVIN = 2.5V PVIN = VDDQ = 1.5V 0.740 0.763 0.786 V 0.731 0.752 0.773 V IOUT = +0.5A, AVIN = 2.5V PVIN = VDDQ = 1.6V IOUT = -0.5A, AVIN = 2.5V PVIN = VDDQ = 1.6V 0.790 0.813 0.836 V 0.781 0.802 0.823 V IOUT = 0A, AVIN = 2.5V VTT Output Voltage (DDR III) (Note 8) VTT Output Voltage Offset (VREF - VTT) for DDR I (Note 8) IOUT = 0A -30 0 30 mV IOUT = -1.5A -30 0 30 mV IOUT = +1.5A -30 0 30 mV IOUT = 0A -30 0 30 mV IOUT = -0.5A -30 0 30 mV IOUT = +0.5A -30 0 30 mV IOUT = 0A -30 0 30 mV IOUT = 0.2A -30 0 30 mV IOUT = 0.4A -30 0 30 mV IOUT = 0.5A -30 0 30 mV 320 500 A VTT Output Voltage Offset (VREF - VTT) for DDR II (Note 8) VOSVtt VTT Output Voltage Offset (VREF - VTT) for DDR III (Note 8) IQ ZVDDQ ISD IQ_SD Quiescent Current (Note 6) 100 k Quiescent current in shutdown (Note 6) SD = 0V 115 150 A Shutdown leakage current SD = 0V 2 5 A VIH Minimum Shutdown High Level VIL Maximum Shutdown Low Level Iv VTT leakage current in shutdown www.ti.com IOUT = 0A VDDQ Input Impedance V 1.9 SD = 0V VTT = 1.25V 4 1 0.8 V 10 A ISENSE TSD Parameter Conditions Min Typ Max Units VSENSE Input current 13 nA Thermal Shutdown (Note 7) 165 C 10 C TSD_HYS Thermal Shutdown Hysteresis Note 1: Absolute maximum ratings indicate limits beyond which damage to the device may occur. Operating range indicates conditions for which the device is intended to be functional, but does not guarantee specific performance limits. For guaranteed specifications and test conditions see Electrical Characteristics. The guaranteed specifications apply only for the test conditions listed. Some performance characteristics may degrade when the device is not operated under the listed test conditions. Note 2: VDDQ voltage must be less than 2 x (AVIN - 1) or 6V, whichever is smaller. Note 3: The human body model is a 100 pF capacitor discharged through a 1.5 k resistor into each pin. Note 4: At elevated temperatures, devices must be derated based on thermal resistance. The device in the SO-8 package must be derated at JA = 151.2 C/W junction to ambient with no heat sink. Note 5: Limits are 100% production tested at 25C. Limits over the operating temperature range are guaranteed through correlation using Statistical Quality Control (SQC) methods. The limits are used to calculate National's Average Outgoing Quality Level (AOQL). Note 6: Quiescent current is defined as the current flow into AVIN. Note 7: The maximum allowable power dissipation is a function of the maximum junction temperature, TJ(MAX), the junction to ambient thermal resistance, JA, and the ambient temperature, TA. Exceeding the maximum allowable power dissipation will cause excessive die temperature and the regulator will go into thermal shutdown. Note 8: VTT load regulation is tested by using a 10 ms current pulse and measuring VTT. 5 www.ti.com LP2998 Symbol LP2998 Typical Performance Characteristics Unless otherwise specified VIN = AVIN = PVIN = 2.5V Iq vs AVIN in SD Iq vs AVIN 30026920 30026921 VIH and VIL VREF vs VDDQ 30026922 30026924 VTT vs VDDQ ISD vs AVIN over Temperature 30026927 30026926 www.ti.com 6 LP2998 Iq vs AVIN over Temperature Maximum Sourcing Current vs AVIN (VDDQ = 1.8V, PVIN = 1.8V) 30026928 30026935 Maximum Sinking Current vs AVIN (VDDQ = 1.8V) Maximum Sourcing Current vs AVIN (VDDQ = 2.5V, PVIN = 1.8V) 30026936 30026931 Maximum Sourcing Current vs AVIN (VDDQ = 2.5V, PVIN = 2.5V) Maximum Sourcing Current vs AVIN (VDDQ = 2.5V, PVIN = 3.3V) 30026932 30026933 7 www.ti.com LP2998 Maximum Sinking Current vs AVIN (VDDQ = 2.5V) Maximum Sourcing Current vs AVIN (VDDQ = 1.8V, PVIN = 3.3V) 30026934 www.ti.com 30026937 8 LP2998 Block Diagram 30026905 Description Pin Descriptions The LP2998 is a linear bus termination regulator designed to meet the JEDEC requirements of SSTL-2 and SSTL-18. The output, VTT is capable of sinking and sourcing current while regulating the output voltage equal to VDDQ / 2. The output stage has been designed to maintain excellent load regulation while preventing shoot through. The LP2998 also incorporates two distinct power rails that separates the analog circuitry from the power output stage. This allows a split rail approach to be utilized to decrease internal power dissipation. It also permits the LP2998 to provide a termination solution for the next generation of DDR-SDRAM memory (DDRII). The LP2998 can also be used to provide a termination voltage for other logic schemes such as SSTL-3 or HSTL. Series Stub Termination Logic (SSTL) was created to improve signal integrity of the data transmission across the memory bus. This termination scheme is essential to prevent data error from signal reflections while transmitting at high frequencies encountered with DDR-SDRAM. The most common form of termination is Class II single parallel termination. This involves one RS series resistor from the chipset to the memory and one RT termination resistor. Typical values for RS and RT are 25 Ohms, although these can be changed to scale the current requirements from the LP2998. This implementation can be seen below in . AVIN AND PVIN AVIN and PVIN are the input supply pins for the LP2998. AVIN is used to supply all the internal control circuitry. PVIN, however, is used exclusively to provide the rail voltage for the output stage used to create VTT. These pins have the capability to work off separate supplies, under the condition that AVIN is always greater than or equal to PVIN. For SSTL-18 applications, it is recommended to connect PVIN to the 1.8V rail used for the memory core and AVIN to a rail within its operating range of 2.2V to 5.5V (typically a 2.5V supply). PVIN should always be used with either a 1.8V or 2.5V rail. This prevents the thermal limit from tripping because of excessive internal power dissipation. If the junction temperature exceeds the thermal shutdown threshold, the part will enter a shutdown state identical to the manual shutdown where VTT is tri-stated and VREF remains active. A lower rail, such as 1.5V can be used but it will reduce the maximum output current. Therefore it is not recommended for most termination schemes. VDDQ VDDQ is the input used to create the internal reference voltage for regulating VTT. The reference voltage is generated from a resistor divider of two internal 50k resistors. This guarantees that VTT will precisely track VDDQ / 2. The optimal implementation of VDDQ is as a remote sense. This can be achieved by connecting VDDQ directly to the 1.8V rail at the DIMM instead of PVIN. This ensures that the reference voltage precisely tracks the DDR memory rails without a large voltage drop from the power lines. For SSTL-18 applications, VDDQ will be a 1.8V signal, which will create a 0.9V termination voltage at VTT (See Electrical Characteristics Table for exact values of VTT over temperature). VSENSE The purpose of the sense pin is to provide improved remote load regulation. In most motherboard applications, the termination resistors will connect to VTT in a long plane. If the output voltage was regulated only at the output of the LP2998, then the long trace will cause a significant IR drop resulting in a termination voltage lower at one end of the bus than the other. The VSENSE pin can be used to improve this performance by connecting it to the middle of the bus. This will provide a better distribution across the entire termination bus. If remote load regulation is not used, then the VSENSE pin must still be con- 30026906 FIGURE 1. SSTL-Termination Scheme 9 www.ti.com LP2998 nected to VTT. Care should be taken when a long VSENSE trace is implemented in close proximity to the memory. Noise pickup in the VSENSE trace can cause problems with precise regulation of VTT. A small 0.1uF ceramic capacitor placed next to the VSENSE pin can help filter any high frequency signals and prevent errors. pin, a small 0.1uF ceramic capacitor is sufficient to prevent excessive noise from coupling into the device. OUTPUT CAPACITOR The LP2998 has been designed to be insensitive of output capacitor size or ESR (Equivalent Series Resistance). This allows the flexibility to use any capacitor desired. The choice for output capacitor will be determined solely on the application and the requirements for load transient response of VTT. As a general recommendation the output capacitor should be sized above 100 F with a low ESR for SSTL applications with DDR-SDRAM. The value of ESR should be determined by the maximum current spikes expected and the extent at which the output voltage is allowed to droop. Several capacitor options are available on the market and a few of these are highlighted below: AL - It should be noted that many aluminum electrolytics only specify impedance at a frequency of 120 Hz, which indicates they have poor high frequency performance. Only aluminum electrolytics that have an impedance specified at a higher frequency (100 kHz) should be used for the LP2998. To improve the ESR several AL electrolytics can be combined in parallel for an overall reduction. An important note to be aware of is the extent at which the ESR will change over temperature. Aluminum electrolytic capacitors tend to have rapidly increasing ESR at cold temperatures. Ceramic - Ceramic capacitors typically have a low capacitance, in the range of 10 to 100 F. They also have excellent AC performance for bypassing noise because of very low ESR (typically less than 10 m). However, some dielectric types do not have good capacitance characteristics as a function of voltage and temperature. Because of the typically low value of capacitance, it is recommended to use ceramic capacitors in parallel with another capacitor such as an aluminum electrolytic. A dielectric of X5R or better is recommended for all ceramic capacitors. Hybrid - Several hybrid capacitors such as OS-CON and SP are available from several manufacturers. These offer a large capacitance while maintaining a low ESR. These are the best solution when size and performance are critical, although their cost is typically higher than any other capacitor type. SHUTDOWN The LP2998 contains an active low shutdown pin that can be used for suspend to RAM functionality. In this condition, the VTT output will tri-state while the VREF output remains active providing a constant reference signal for the memory and chipset. During shutdown, VTT should not be exposed to voltages that exceed PVIN. With the shutdown pin asserted low the quiescent current of the LP2998 will drop. However, VDDQ will always maintain its constant impedance of 100k for generating the internal reference. Therefore, to calculate the total power loss in shutdown, both currents need to be considered. For more information refer to the Thermal Dissipation section. The shutdown pin also has an internal pull-up current. Therefore, to turn the part on, the shutdown pin can either be connected to AVIN or left open. VREF VREF provides the buffered output of the internal reference voltage VDDQ / 2. This output should be used to provide the reference voltage for the Northbridge chipset and memory. Since the inputs typically have an extremely high impedance, there should be little current drawn from VREF. For improved performance, an output bypass capacitor can be placed, close to the pin, to help with noise. A ceramic capacitor in the range of 0.1 F to 0.01 F is recommended. This output remains active during the shutdown state and thermal shutdown events for the suspend to RAM functionality. VTT VTT is the regulated output that is used to terminate the bus resistors. It is capable of sinking and sourcing current while regulating the output precisely to VDDQ / 2. The LP2998 is designed to handle continuous currents of up to +/- 1.5A with excellent load regulation. If a transient is expected to last above the maximum continuous current rating for a significant amount of time, then the bulk output capacitor should be sized large enough to prevent an excessive voltage drop. If the LP2998 is to operate in elevated temperatures for long durations, care should be taken to ensure that the maximum operating junction temperature is not exceeded. Proper thermal de-rating should always be used (Please refer to the Thermal Dissipation section). If the junction temperature exceeds the thermal shutdown threshold, VTT will tri-state until the part returns below the temperature hysteresis trip-point. Thermal Dissipation Since the LP2998 is a linear regulator, any current flow from VTT will result in internal power dissipation and heat generation. To prevent damaging the part by exceeding the maximum allowable operating junction temperature, care should be taken to derate the part based on the maximum expected ambient temperature and power dissipation. The maximum allowable internal temperature rise (TRmax) can be calculated given the maximum ambient temperature (TAmax) of the application and the maximum allowable junction temperature (TJmax). Component Selections INPUT CAPACITOR The LP2998 does not require a capacitor for input stability, but it is recommended for improved performance during large load transients to prevent the input rail from dropping. The input capacitor should be located as close as possible to the PVIN pin. Several recommendations exist and is dependent on the application required. A typical value recommended for AL electrolytic capacitors is 22 F. Ceramic capacitors can also be used. A value in the range of 10 F with X5R or better would be an ideal choice. The input capacitance can be reduced if the LP2998 is placed close to the bulk capacitance from the output of the 1.8V DC-DC converter. For the AVIN www.ti.com TRmax = TJmax - TAmax From this equation, the maximum power dissipation (PDmax) of the part can be calculated: PDmax = TRmax / JA The JA of the LP2998 will depend on several variables: the package used; the thickness of copper; the number of vias and the airflow. For instance, the JA of the SO-8 is 163C/W with the package mounted to a standard 8x4 2-layer board with 1oz. copper, no airflow, and 0.5W dissipation at room temperature. This value can be reduced to 151.2C/W by changing to a 3x4 board with 2 oz. copper that is the JEDEC 10 to operate with higher power dissipation. The internal power dissipation can be calculated by summing the three main sources of loss: output current at VTT, either sinking or sourcing, and quiescent currents at AVIN and VDDQ. During the active state (when shutdown is not held low) the total internal power dissipation can be calculated from the following equations: PD = PAVIN + PVDDQ + PVTT Where, PAVIN = IAVIN * VAVIN PVDDQ = VVDDQ * IVDDQ = VVDDQ2 x RVDDQ To calculate the maximum power dissipation at VTT, both the sinking and sourcing current conditions need to be examined. Although only one equation will add into the total, VTT cannot source and sink current simultaneously. PVTT = VVTT x ILOAD (Sinking) or PVTT = ( VPVIN - VVTT) x ILOAD (Sourcing) The power dissipation of the LP2998 can also be calculated during the shutdown state. During this condition the output VTT will tri-state. Therefore, that term in the power equation will disappear as it cannot sink or source any current (leakage is negligible). The only losses during shutdown will be the reduced quiescent current at AVIN and the constant impedance that is seen at the VDDQ pin. 30026907 FIGURE 2. JA vs Airflow (SO-8) Additional improvements can be made by the judicious use of vias to connect the part and dissipate heat to an internal ground plane. Using larger traces and more copper on the top side of the board can also help. With careful layout, it is possible to reduce the JA further than the nominal values shown in Figure 2 Optimizing the JA and placing the LP2998 in a section of a board exposed to lower ambient temperature allows the part PD = PAVIN + PVDDQ PAVIN = IAVIN x VAVIN PVDDQ = VVDDQ * IVDDQ = VVDDQ2 x RVDDQ 11 www.ti.com LP2998 standard. Figure 2 shows how the JA varies with airflow for the two boards mentioned. LP2998 Typical Application Circuits Several different application circuits have been shown in Figure 3 through Figure 12 to illustrate some of the options that are possible in configuring the LP2998. Graphs of the individual circuit performance can be found in the Typical Performance Characteristics section of the datasheet. These curves illustrate how the maximum output current is affected by changes in AVIN and PVIN. SSTL-2 APPLICATIONS For the majority of applications that implement the SSTL-2 termination scheme it is recommended to connect all the input rails to the 2.5V rail. This provides an optimal trade-off between power dissipation and component count and selection. An example of this circuit can be seen in Figure 3. 30026910 FIGURE 3. Recommended SSTL-2 Implementation If power dissipation or efficiency is a major concern then the LP2998 has the ability to operate on split power rails (see Figure 4). The output stage (PVIN) can be operated on a lower rail such as 1.8V and the analog circuitry (AVIN) can be connected to a higher rail such as 2.5V, 3.3V or 5V. This allows the internal power dissipation to be lowered when sourcing current from VTT. The disadvantage of this circuit is that the maximum continuous current is reduced because of the lower rail voltage, although it is adequate for all motherboard SSTL-2 applications. Increasing the output capacitance can also help if periods of large load transients will be encountered. 30026911 FIGURE 4. Lower Power Dissipation SSTL-2 Implementation The third option for SSTL-2 applications in the situation that a 1.8V rail is not available and it is not desirable to use 2.5V, is to connect the LP2998 power rail to 3.3V (see Figure 5). In this situation AVIN will be limited to operation on the 3.3V or 5V rail as PVIN can never exceed AVIN. This configuration has the ability to provide the maximum continuous output cur- www.ti.com rent at the downside of higher thermal dissipation. Care should be taken to prevent the LP2998 from experiencing large current levels which cause the device to exceed the maximum operating junction temperature. Because of this risk it is not recommended to supply the output stage with a voltage higher than a nominal 3.3V rail. 12 LP2998 30026912 FIGURE 5. SSTL-2 Implementation With Higher Voltage Rails in the Typical Performance Characteristics. Figure 6 shows the recommended circuit configuration for DDR-II applications. The output stage is connected to the 1.8V rail and the AVIN pin can be connected to either a 2.5, 3.3V or 5.5V rail. DDR-II APPLICATIONS With the separate VDDQ pin and an internal resistor divider it is possible to use the LP2998 in applications utilizing DDRII memory. Figure 6 and Figure 7 show several implementations of recommended circuits with output curves displayed 30026913 FIGURE 6. Recommended DDR-II Termination If it is not desirable to use the 1.8V rail it is possible to connect the output stage to a 3.3V rail. Care should be taken to not exceed the maximum operating junction temperature as the thermal dissipation increases with lower VTT output voltages. For this reason it is not recommended to power PVIN with a rail higher than the nominal 3.3V. The advantage of this configuration is that it has the ability to source and sink a higher maximum continuous current. 30026914 FIGURE 7. DDR-II Termination With Higher Voltage Rails 13 www.ti.com LP2998 from VTT to the VSENSE pin. This has been illustrated in Figure 8 and Figure 9. Figure 8 shows how to use two resistors to level shift VTT above the internal reference voltage of VDDQ/ 2. To calculate the exact voltage at VTT the following equation can be used. LEVEL SHIFTING If standards other than SSTL-2 are required, such as SSTL-3, it may be necessary to use a different scaling factor than 0.5 times VDDQ for regulating the output voltage. Several options are available to scale the output to any voltage required. One method is to level shift the output by using feedback resistors VTT = VDDQ/2 (1 + R1/R2) 30026915 FIGURE 8. Increasing VTT by Level Shifting VTT = VDDQ/2 (1 - R1/R2) Conversely, the R2 resistor can be placed between VSENSE and VDDQ to shift the VTT output lower than the internal reference voltage of VDDQ/2. The equation relating to VTT and the resistors can be used as shown: 30026916 FIGURE 9. Decreasing VTT by Level Shifting VREF voltage of approximately 0.75V for the termination resistors. AVIN and PVIN should be connected to a 2.5V rail for optimal performance. HSTL APPLICATIONS The LP2998 can be easily adapted for HSTL applications by connecting VDDQ to the 1.5V rail. This will produce a VTT and 30026917 FIGURE 10. HSTL Application www.ti.com 14 OUTPUT CAPACITOR SELECTION For applications utilizing the LP2998 to terminate SSTL-2 I/O signals the typical application circuit shown in Figure 11 can be implemented. 30026918 FIGURE 11. Typical SSTL-2 Application Circuit This circuit permits termination in a minimum amount of board space and component count. Capacitor selection can be varied depending on the number of lines terminated and the maximum load transient. However, with motherboards and other applications where VTT is distributed across a long plane, it is recommended to use multiple bulk capacitors in addition to high frequency decoupling. Figure 12 depicts an example circuit where 2 bulk output capacitors could be situated at both ends of the VTT plane for optimal placement. Large aluminum electrolytic capacitors are typically used for their low ESR and low cost. 30026919 FIGURE 12. Typical SSTL-2 Application Circuit for Motherboards In most PC applications, an extensive amount of decoupling is required because of the long interconnects encountered with the DDR-SDRAM DIMMs mounted on modules. As a re- sult, bulk aluminum electrolytic capacitors in the range of 1000uF are typically used. 15 www.ti.com LP2998 ence provided by a local resistor divider or one of the LP2998 signals. Because VREF and VTT are expected to track and the part to part variations are minor, there should be little difference between the reference signals of each LP2998. QDR APPLICATIONS Quad data rate (QDR) applications utilize multiple channels for improved memory performance. However, this increase in bus lines increases the current levels required for termination. The recommended approach in terminating multiple channels is to use a dedicated LP2998 for each channel. This simplifies layout and reduces the internal power dissipation for each regulator. Separate VREF signals can be used for each DIMM bank from the corresponding regulator with the chipset refer- LP2998 PCB Layout Considerations 1. 2. 3. 4. The input capacitor for the power rail should be placed as close as possible to the PVIN pin. VSENSE should be connected to the VTT termination bus at the point where regulation is required. For motherboard applications an ideal location would be at the center of the termination bus. VDDQ can be connected remotely to the VDDQ rail input at either the DIMM or the Chipset. This provides the most accurate point for creating the reference voltage. For improved thermal performance excessive top side copper should be used to dissipate heat from the www.ti.com 5. 6. 16 package. Numerous vias from the ground connection to the internal ground plane will help. Additionally these can be located underneath the package if manufacturing standards permit. Care should be taken when routing the VSENSE trace to avoid noise pickup from switching I/O signals. A 0.1uF ceramic capacitor located close to the SENSE can also be used to filter any unwanted high frequency signal. This can be an issue especially if long SENSE traces are used. VREF should be bypassed with a 0.01 F or 0.1 F ceramic capacitor for improved performance. This capacitor should be located as close as possible to the VREF pin. LP2998 Physical Dimensions inches (millimeters) unless otherwise noted 8-Lead Small Outline Package (M8) NS Package Number M08A 8-Lead PSOP Package (PSOP-8) NS Package Number MRA08A 17 www.ti.com LP2998 DDR-I and DDR-II Termination Regulator Notes www.ti.com IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI's standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP(R) Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap Wireless Connectivity www.ti.com/wirelessconnectivity TI E2E Community Home Page e2e.ti.com Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2012, Texas Instruments Incorporated