Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs) Flexible Termination System (FT-CAP), X7R Dielectric, 6.3 - 250 VDC (Commercial Grade) Overview KEMET's Flexible Termination (FT-CAP) multilayer ceramic capacitor in X7R dielectric incorporates a unique, flexible termination system that is integrated with KEMET's standard termination materials. A conductive silver epoxy is utilized between the base metal and nickel barrier layers of KEMET's standard termination system in order to establish pliability while maintaining terminal strength, solderability and electrical performance. This technology was developed in order to address the primary failure mode of MLCCs- flex cracks, which are typically the result of excessive tensile and shear stresses produced during board flexure and thermal cycling. Flexible termination technology inhibits the transfer of board stress to the rigid ceramic body, therefore mitigating flex cracks which can result in low IR or short circuit failures. (KPS) product lines by providing a complete portfolio of flex mitigation solutions. Combined with the stability of an X7R dielectric and designed to accommodate all capacitance requirements, these flexrobust devices are RoHS-compliant, offer up to 5 mm of flex-bend capability and exhibit a predictable change in capacitance with respect to time and voltage. Capacitance change with reference to ambient temperature is limited to 15% from -55C to +125C. In addition to commercial grade, automotive grade devices are available which meet the demanding Automotive Electronics Council's AEC-Q200 qualification requirements. Although this technology does not eliminate the potential for mechanical damage that may propagate during extreme environmental and handling conditions, it does provide superior flex performance over standard termination systems. FT-CAP complements KEMET's Open Mode, Floating Electrode (FE-CAP), Floating Electrode with Flexible Termination (FF-CAP) and KEMET Power Solutions Click image above for interactive 3D content Ordering Information C Ceramic 1206 Case Size Specification/ (L" x W") Series 0603 0805 1206 1210 1808 1812 1825 2220 2225 1 X X = Flexible Termination Open PDF in Adobe Reader for full functionality 106 Capacitance Code (pF) Two significant digits + number of zeros K Capacitance Tolerance J = 5% K = 10% M = 20% 4 R A Rated Failure Voltage Dielectric Rate/ (VDC) Design 9 = 6.3 8 = 10 4 = 16 3 = 25 5 = 50 1 = 100 2 = 200 A = 250 R = X7R C TU Termination Finish1 Packaging/Grade (C-Spec)2 A = N/A C = 100% Matte Sn See "Packaging L = SnPb (5% Pb minimum) C-Spec Ordering Options Table" below Additional termination finish options may be available. Contact KEMET for details. One world. One KEMET (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 * 864-963-6300 * www.kemet.com C1013_X7R_FT-CAP_SMD * 3/21/2017 1 Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs) Flexible Termination System (FT-CAP), X7R Dielectric, 6.3 - 250 VDC (Commercial Grade) Packaging C-Spec Ordering Options Table Packaging Type1 Bulk Bag/Unmarked 7" Reel/Unmarked 13" Reel/Unmarked 7" Reel/Marked 13" Reel/Marked 7" Reel/Unmarked/2mm pitch2 13" Reel/Unmarked/2mm pitch2 Packaging/Grade Ordering Code (C-Spec) Not required (Blank) TU 7411 (EIA 0603 and smaller case sizes) 7210 (EIA 0805 and larger case sizes) TM 7040 (EIA 0603 and smaller case sizes) 7215 (EIA 0805 and larger case sizes) 7081 7082 Default packaging is "Bulk Bag". An ordering code C-Spec is not required for "Bulk Bag" packaging. The terms "Marked" and "Unmarked" pertain to laser marking option of capacitors. All packaging options labeled as "Unmarked" will contain capacitors that have not been laser marked. Please contact KEMET if you require a laser marked option. For more information see "Capacitor Marking". 2 The 2 mm pitch option allows for double the packaging quantity of capacitors on a given reel size. This option is limited to EIA 0603 (1608 metric) case size devices. For more information regarding 2 mm pitch option see "Tape & Reel Packaging Information". 1 1 Benefits * * * * * -55C to +125C operating temperature range Superior flex performance (up to 5 mm) High capacitance flex mitigation Lead (Pb)-free, RoHS and REACH compliant EIA 0603, 0805, 1206, 1210, 1808, 1812, 1825, 2220, and 2225 case sizes * DC voltage ratings of 6.3 V, 10 V, 16 V, 25 V, 50 V, 100 V, 200 V, and 250 V * * * * * Capacitance offerings ranging from 180 pF to 22 F Available capacitance tolerances of 5%, 10%, and 20% Automotive (AEC-Q200) grade available Non-polar device, minimizing installation concerns 100% pure matte tin-plated termination finish allowing for excellent solderability * SnPb termination finish option available upon request (5% Pb minimum) Applications Typical applications include circuits with a direct battery or power source connection, critical and safety relevant circuits without (integrated) current limitation and any application that is subject to high levels of board flexure or temperature cycling. Examples include raw power input side filtering (power plane/bus), high current applications (automobile battery line) and circuits that cannot be fused to open. Markets include consumer, medical, industrial (power supply), automotive, aerospace and telecom. (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 * 864-963-6300 * www.kemet.com C1013_X7R_FT-CAP_SMD * 3/21/2017 2 Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs) Flexible Termination System (FT-CAP), X7R Dielectric, 6.3 - 250 VDC (Commercial Grade) Dimensions - Millimeters (Inches) L W B T S EIA Size Code Metric Size Code 0603 1608 0805 2012 1206 3216 1210 3225 1808 4520 1812 4532 1825 4564 2220 5650 2225 5664 L Length W Width 1.60 (0.063) 0.17 (0.007) 2.00 (0.079) 0.30 (0.012) 3.30 (0.130) 0.40 (0.016) 3.30 (0.130) 0.40 (0.016) 4.70 (0.185) 0.50 (0.020) 4.50 (0.178) 0.40 (0.016) 4.60 (0.181) 0.40 (0.016) 5.90 (0.232) 0.75 (0.030) 5.90 (0.232) 0.75 (0.030) 0.80 (0.032) 0.15 (0.006) 1.25 (0.049) 0.30 (0.012) 1.60 (0.063) 0.35 (0.013) 2.60 (0.102) 0.30 (0.012) 2.00 (0.079) 0.20 (0.008) 3.20 (0.126) 0.30 (0.012) 6.40 (0.252) 0.40 (0.016) 5.00 (0.197) 0.40 (0.016) 6.40 (0.248) 0.40 (0.016) S Separation Minimum T Thickness B Bandwidth See Table 2 for Thickness 0.45 (0.018) 0.15 (0.006) 0.50 (0.02) 0.25 (0.010) 0.60 (0.024) 0.25 (0.010) 0.60 (0.024) 0.25 (0.010) 0.70 (0.028) 0.35 (0.014) 0.70 (0.028) 0.35 (0.014) 0.70 (0.028) 0.35 (0.014) 0.70 (0.028) 0.35 (0.014) 0.70 (0.028) 0.35 (0.014) 0.58 (0.023) 0.75 (0.030) N/A Mounting Technique Solder Wave or Solder Reflow Solder Reflow Only Qualification/Certification Commercial Grade products are subject to internal qualification. Details regarding test methods and conditions are referenced in Table 4, Performance & Reliability. Environmental Compliance Lead (Pb)-free, RoHS, and REACH compliant without exemptions (excluding SnPb termination finish option). (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 * 864-963-6300 * www.kemet.com C1013_X7R_FT-CAP_SMD * 3/21/2017 3 Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs) Flexible Termination System (FT-CAP), X7R Dielectric, 6.3 - 250 VDC (Commercial Grade) Electrical Parameters/Characteristics Item Parameters/Characteristics Operating Temperature Range -55C to +125C Capacitance Change with Reference to +25C and 0 Vdc Applied (TCC) 15% Aging Rate (Maximum % Capacitance Loss/Decade Hour) 3.0% 1 2 3 4 Dielectric Withstanding Voltage (DWV) Dissipation Factor (DF) Maximum Limit at 25C Insulation Resistance (IR) Minimum Limit at 25C 250% of rated voltage (51 seconds and charge/discharge not exceeding 50mA) See Dissipation Factor Limit Table See Insulation Resistance Limit Table (Rated voltage applied for 1205 seconds at 25C) 1Regarding Aging Rate: Capacitance measurements (including tolerance) are indexed to a referee time of 1,000 hours. DWV is the voltage a capacitor can withstand (survive) for a short period of time. It exceeds the nominal and continuous working voltage of the capacitor. 3 Capacitance and dissipation factor (DF) measured under the following conditions: 1kHz 50Hz and 1.0 0.2 Vrms if capacitance 10F 120Hz 10Hz and 0.5 0.1 Vrms if capacitance >10F 4 To obtain IR limit, divide M-F value by the capacitance and compare to G limit. Select the lower of the two limits. Note: When measuring capacitance it is important to ensure the set voltage level is held constant. The HP4284 and Agilent E4980 have a feature known as Automatic Level Control (ALC). The ALC feature should be switched to "ON". 1 2 (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 * 864-963-6300 * www.kemet.com C1013_X7R_FT-CAP_SMD * 3/21/2017 4 Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs) Flexible Termination System (FT-CAP), X7R Dielectric, 6.3 - 250 VDC (Commercial Grade) Post Environmental Limits High Temperature Life, Biased Humidity, Moisture Resistance EIA Case Size Rated DC Voltage Capacitance < 16 0603 16 / 25 0805 12061 1210 1808 - 2225 1 < 1.0F 20% 10% of Initial Limit 3.0 20.0 < 4.7F 7.5 4.7F 20.0 < 4.7F 5.0 4.7F 20.0 25 All 5.0 > 25 All 3.0 < 16 All 7.5 16 / 25 All 5.0 > 25 All 3.0 < 16 All 7.5 16 / 25 All 5.0 > 25 All 3.0 < 16 All 7.5 16 / 25 All 5.0 > 25 All 3.0 16 Insulation Resistance 5.0 1.0F < 16 Capacitance Shift 7.5 > 25 All Dissipation Factor (Maximum %) For Capacitance values 4.7 f and 10 F DF Post Value is 20% (All Voltages). (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 * 864-963-6300 * www.kemet.com C1013_X7R_FT-CAP_SMD * 3/21/2017 5 Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs) Flexible Termination System (FT-CAP), X7R Dielectric, 6.3 - 250 VDC (Commercial Grade) Insulation Resistance Limit Table (X7R Dielectric) EIA Case Size 1,000 Megohm Microfarads or 100 G 500 Megohm Microfarads or 10 G 100 Megohm Microfarads or 10 G 0402 0603 0805 1206 1210 1808 1812 1825 2220 2225 < 0.012 F < 0.047 F < 0.15 F < 0.47 F < 0.39 F ALL < 2.2 F ALL < 10 F ALL 0.012 F 0.047 f < 0.47 f 0.15 F < 2.2 f 0.47 F < 4.7 f 0.39 F < 10 f N/A 2.2 F N/A 10 F N/A N/A 0.47 f 2.2 f 4.7 f 10 f N/A N/A N/A N/A N/A Dissipation Factor (DF) Limit Table EIA Case Size Rated DC Voltage 0603 < 16 16/25 > 25 All < 16 0805 12061 1210 1808 - 2225 1 16 25 > 25 < 16 16/25 > 25 < 16 16 / 25 > 25 < 16 16/25 > 25 Capacitance < 1.0F 1.0F < 4.7F 4.7F < 4.7F 4.7F All All All All All All All All All All All Dissipation Factor (Maximum %) 5.0 3.5 2.5 10.0 5.0 10.0 3.5 10.0 3.5 2.5 5.0 3.5 2.5 5.0 3.5 2.5 5.0 3.5 2.5 For Capacitance values 4.7 f and 10 F DF Value is 10% (All Voltages). (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 * 864-963-6300 * www.kemet.com C1013_X7R_FT-CAP_SMD * 3/21/2017 6 Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs) Flexible Termination System (FT-CAP), X7R Dielectric, 6.3 - 250 VDC (Commercial Grade) Table 1A - Capacitance Range/Selection Waterfall (0603 - 1210 Case Sizes) 4 3 5 1 2 9 8 4 3 5 1 2 200 8 250 9 FN FN FN FN FN FN FN FN FN FN FN FN FN FN FN FN FN FN FN FN FN FN FQ FQ FQ FQ FX FX FX FX FX FA FU FU FU FU FJ FE FA FZ FQ FA FN FN FN FN FN FN FN FN FN FN FN FN FN FN FN FN FN FN FN FN FN FN FQ FQ FQ FQ FX FX FX FX FX FA FU FU FU FU FJ FE FA FZ FQ FA FN FN FN FN FN FN FN FN FN FN FN FN FN FN FN FN FN FN FN FN FN FN FQ FQ FQ FQ FX FX FX FX FX FA FU FU FU FU FJ FE FA FZ FQ FA FN FN FN FN FN FN FN FN FN FN FN FN FN FN FN FN FN FN FN FN FN FN FQ FQ FQ FQ FX FX FX FX FX FA FU FU FU FU FJ FZ FM FZ FZ FU FN FN FN FN FN FN FN FN FN FN FN FN FN FN FN FN FN FN FN FN FN FN FQ FQ FQ FQ FX FX FX FX FX FA FU FZ FZ FZ FZ FU FM FK FS FN FN FN FN FN FN FN FN FN FN FN FN FN FN FN FN FN FN FN FQ FX FX FX FX FX FX FX FX FX FA FZ FL FM FH FM FJ FK FN FN FN FN FN FN FN FN FN FN FN FN FN FN FN FN FQ FQ FQ FA FZ FU FM FK FK FN FN FN FN FN FN FN FN FN FN FN FN FN FN FN FN FQ FQ FQ FA FZ FU FM FK FK 200 DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR 250 DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DS DS DS DG DG 100 DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DD DD DD DD DD DD DS DS DS DS DS DG DG DG DG A 100 DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DD DD DD DR DD DD DG DG DD DD DS DS DH DH 25 DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DD DD DD DR DR DR DR DR DD DG DG DG DG DG DG DG 2 50 DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DD DD DD DR DR DR DR DR DD DG DG DG DD DD DD DD DS DG DG DG 1 25 DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DD DD DD DR DR DR DR DR DD DG DG DG DD DD DD DD DS DG DG DG 5 50 DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DD DD DD DR DR DR DR DR DD DG DG DG DD DD DD DD DS DG DG DG 3 16 25 50 CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ 4 10 16 CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ 8 16 10 CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ 9 10 6.3 CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ A 6.3 250 CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ 2 250 100 200 CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ 1 6.3 5 250 3 100 4 C1210X 200 8 100 50 9 200 16 25 A 50 10 2 16 6.3 1 25 5 10 3 6.3 100 200 Case Size/ Series 4 100 A 9 8 4 3 5 1 2 A Product Availability and Chip Thickness Codes - See Table 2 for Chip Thickness Dimensions C0603X EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ ER ER ER ER EQ EQ EQ ER ES ET EF EF ES EF ES ES EN ES EF EF EH EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ ER ER ER ER EQ EQ EQ ER ES ET EF EF ES EF ES ES EN ES EF EF EH EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ ER ER ER ER EQ EQ EQ ER ES ET EF EF ES EF ES ES EN ES EF EF EH EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ ER ER ER ER EQ EQ EQ ER ES ET EF EU EU EU EF EF EH EH EH EH EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ ER ER ER ER ER ER ER ER ER ES ES ES EH EH EH EH EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ ER ER EQ EQ EQ EQ ER ER ER ER EM EU EU EU EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ ES ES ES ES EM EU EU EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ ES ES ES ES EM 6.3 10 16 25 50 100 200 EQ EQ EQ EQ EQ 250 Voltage Code 8 CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ CJ Cap Tolerance J K M J K M J K M J K M J K M J K M J K M J K M J K M J K M J K M J K M J K M J K M J K M J K M J K M J K M J K M J K M J K M J K M J K M J K M J K M J K M J K M K M J J K M J K M J K M J K M J K M J K M J K M J K M J K M J K M J K M J K M J K M J K M J K M J K M J K M J K M J K M J K M J K M J K M J K M J K M J K M J K M J K M Rated Voltage (VDC) 9 200 2 25 1 50 5 25 3 50 4 16 Cap Code 8 10 Cap 9 16 181 221 271 331 391 471 561 681 821 102 122 152 182 222 272 332 392 472 562 682 822 103 123 153 183 223 273 333 393 473 563 683 823 104 124 154 184 224 274 334 394 474 564 684 824 105 125 155 185 225 275 335 395 475 565 Voltage Code Rated Voltage (VDC) C1206X 10 180 pF 220 pF 270 pF 330 pF 390 pF 470 pF 560 pF 680 pF 820 pF 1,000 pF 1,200 pF 1,500 pF 1,800 pF 2,200 pF 2,700 pF 3,300 pF 3,900 pF 4,700 pF 5,600 pF 6,800 pF 8,200 pF 10,000 pF 12,000 pF 15,000 pF 18,000 pF 22,000 pF 27,000 pF 33,000 pF 39,000 pF 47,000 pF 56,000 pF 68,000 pF 82,000 pF 0.10 F 0.12 F 0.15 F 0.18 F 0.22 F 0.27 F 0.33 F 0.39 F 0.47 F 0.56 F 0.68 F 0.82 F 1.0 F 1.2 F 1.5 F 1.8 F 2.2 F 2.7 F 3.3 F 3.9 F 4.7 F 5.6 F C0805X 6.3 Cap Code C0603X 6.3 Cap Case Size/ Series A 9 8 4 3 5 1 2 C0805X (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 * 864-963-6300 * www.kemet.com C1206X C1210X C1013_X7R_FT-CAP_SMD * 3/21/2017 7 Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs) Flexible Termination System (FT-CAP), X7R Dielectric, 6.3 - 250 VDC (Commercial Grade) Table 1A - Capacitance Range/Selection Waterfall (0603 - 1210 Case Sizes) cont'd 2 A 25 200 1 250 5 200 3 250 4 100 8 100 9 50 A 25 2 50 16 1 16 10 5 10 6.3 3 6.3 4 250 8 100 9 C1210X 200 A 25 2 50 1 250 5 100 10 3 200 6.3 4 50 8 16 9 25 2 C1206X 3 5 1 2 A Product Availability and Chip Thickness Codes - See Table 2 for Chip Thickness Dimensions Cap Tolerance EH EH EH EH EH EH EH EH EH FZ FZ FZ FM FU FU FU FK FU FU FU FS C0603X C0805X 5 16 3 10 4 6.3 8 250 9 100 A 200 2 25 16 1 50 10 5 6.3 3 250 4 100 8 200 9 50 2 16 1 25 5 10 3 6.3 4 100 8 Case Size/ Series 25 16 9 Voltage Code 50 10 FS FS 6.3 J K M J K M J K M J K M J K M J K M J K M Rated Voltage (VDC) 1 100 5 200 3 C0805X 200 Cap Code 4 25 Cap 8 50 685 825 106 126 156 186 226 9 16 6.8 F 8.2 F 10 F 12 F 15 F 18 F 22 F Voltage Code Rated Voltage (VDC) 10 Cap Code C0603X 6.3 Cap Case Size/ Series 1 2 A 9 8 4 C1206X C1210X Table 1B - Capacitance Range/Selection Waterfall (1808 - 2225 Case Sizes) Case Size/ Series 5 1 2 A 3 5 1 2 A 5 1 2 A 100 200 250 25 50 100 200 250 50 250 A 200 2 100 1 50 2 5 250 1 3 200 5 A KC KC KC KC KC KC KC KC KC KB KB KB KB KB KB KB KB KB KC KC KC KC KC KC KC KC KC KC KC KC KC KC KC KC KD KE KC KC KC KC KC KC KC KC KC KC KC KC KD KD KD KE KE KE KC KC KC KC KC KC KC KC KC KC KC KC KD KD KD KE KE KE C1808X GB GB GB GB GB GB GB GB GB GB GB GB GB GB GB GB GE GG GG GG GG GG GJ 50 100 200 A 3 5 1 2 C1812X JC JC JC JC JC JC JC JC JC JC JD JD JF JF 100 200 250 2 JC JC JC JC JC JC JC JC JC JC JD JD JF JF 50 1 JC JC JC JC JC JC JC JC JC JC JC JD JF JF 250 5 JC JC JC JC JC JC JC JC JC JC JC JC JC JC JC 200 A JC JC JC JC JC JC JC JC JC JC JC JC JC JC JC 100 HB HB HB HB HB HB HB HB HB HB HB HB HB HB HB HD HD HD HD HF HF 50 HB HB HB HB HB HB HB HB HB HB HB HB HB HB HB HD HD HD HD HF HF 25 HB HB HB HB HB HB HB HB HB HB HB HB HB HB HB HB HB HD HD HF HF 250 HB HB HB HB HB HB HB HB HB HB HB HB HB HB HB HB HB HB HB HB HB HB 200 GB GB GB GB GB GB GB GB GB GB GB GB GB GB GB GB GE GF GG GG GG GG GJ 100 GB GB GB GB GB GB GB GB GB GB GB GB GB GB GB GB GB GB GB GG GG GG GG GG GG GG GG GB 50 GB GB GB GB GB GB GB GB GB GB GB GB GB GB GB GB GB GB GB GB GB GB GB GC GC GE GE GB 250 GB GB GB GB GB GB GB GB GB GB GB GB GB GB GB GB GB GB GB GB GB GB GB GC GC GE GE GB 25 Product Availability and Chip Thickness Codes - See Table 2 for Chip Thickness Dimensions 250 Voltage Code C2225X 100 LD LD LD LD LD LD LD LD C2220X 50 LD LD LD LD LD LD LD LD LD LD LD LD LD LD C1825X 25 LD LD LD LD LD LD LD LD LD LD LD LD LD LD LD LD LD LD LD LD Cap Tolerance J K M J K M J K M J K M J K M J K M J K M J K M J K M J K M J K M J K M J K M J K M J K M J K M J K M J K M J K M J K M J K M J K M J K M J K M J K M J K M J K M J K M J K M J K M Rated Voltage (VDC) C1812X 250 200 Cap Code 2 200 Cap 1 100 472 562 682 822 103 123 153 183 223 273 333 393 473 563 683 823 104 124 154 184 224 274 334 394 474 564 684 824 105 125 5 100 4,700 pF 5,600 pF 6,800 pF 8,200 pF 10,000 pF 12,000 pF 15,000 pF 18,000 pF 22,000 pF 27,000 pF 33,000 pF 39,000 pF 47,000 pF 56,000 pF 68,000 pF 82,000 pF 0.10 F 0.12 F 0.15 F 0.18 F 0.22 F 0.27 F 0.33 F 0.39 F 0.47 F 0.56 F 0.68 F 0.82 F 1.0 F 1.2 F Voltage Code Rated Voltage (VDC) 50 Cap Code C1808X 50 Cap Case Size/ Series A 3 5 1 2 A 5 1 2 A C1825X (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 * 864-963-6300 * www.kemet.com C2220X C2225X C1013_X7R_FT-CAP_SMD * 3/21/2017 8 Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs) Flexible Termination System (FT-CAP), X7R Dielectric, 6.3 - 250 VDC (Commercial Grade) Table 1B - Capacitance Range/Selection Waterfall (1808 - 2225 Case Sizes) cont'd Case Size/ Series 200 250 50 100 200 250 25 50 100 200 250 50 250 100 250 50 A 200 25 2 200 250 1 100 5 100 A 50 2 250 1 200 5 100 3 50 A 25 2 250 1 200 5 100 A 50 2 250 1 200 5 100 3 50 A 25 Voltage Code C2225X 5 1 2 A 3 5 1 2 A 5 1 2 A 3 5 1 2 A 5 1 2 A Product Availability and Chip Thickness Codes - See Table 2 for Chip Thickness Dimensions Cap Tolerance J K M J K M J K M J K M J K M J K M J K M J K M J K M J K M J K M J K M J K M J K M J K M Rated Voltage (VDC) C2220X 250 200 Cap Code 2 C1825X 200 Cap 1 100 155 185 225 275 335 395 475 565 685 825 106 126 156 186 226 5 C1812X 100 1.5 F 1.8 F 2.2 F 2.7 F 3.3 F 3.9 F 4.7 F 5.6 F 6.8 F 8.2 F 10 F 12 F 15 F 18 F 22 F Voltage Code Rated Voltage (VDC) 50 Cap Code C1808X 50 Cap Case Size/ Series GC GE GG GJ GL GC GE GG GJ GL GK GK GC GE GG GJ GL HC HD HF GK JC JD JF JC JD JF JF JO JO JO KC KD KD JO C1808X C1812X C1825X (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 * 864-963-6300 * www.kemet.com C2220X C2225X C1013_X7R_FT-CAP_SMD * 3/21/2017 9 Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs) Flexible Termination System (FT-CAP), X7R Dielectric, 6.3 - 250 VDC (Commercial Grade) Table 2A - Chip Thickness/Tape & Reel Packaging Quantities Paper Quantity1 Plastic Quantity Thickness Code Case Size1 Thickness Range (mm) 7" Reel 13" Reel 7" Reel 13" Reel CJ DR DD DS DG DH EQ ER EN ES ET EF EM EH EU FN FQ FX FE FA FZ FL FU FM FJ FK FS LD GB GC GE GF GG GK GJ HB HC HD HF JC JD JF JO KB KC KD KE 0603 0805 0805 0805 0805 0805 1206 1206 1206 1206 1206 1206 1206 1206 1206 1210 1210 1210 1210 1210 1210 1210 1210 1210 1210 1210 1210 1808 1812 1812 1812 1812 1812 1812 1812 1825 1825 1825 1825 2220 2220 2220 2220 2225 2225 2225 2225 0.80 0.15 0.78 0.20 0.90 0.10 1.00 0.20 1.25 0.15 1.25 0.20 0.78 0.20 0.90 0.20 0.95 0.10 1.00 0.20 1.10 0.20 1.20 0.15 1.25 0.15 1.60 0.20 1.60 0.25 0.78 0.20 0.90 0.20 0.95 0.20 1.00 0.10 1.10 0.15 1.25 0.20 1.40 0.15 1.55 0.20 1.70 0.20 1.85 0.20 2.10 0.20 2.50 0.30 0.90 0.10 1.00 0.10 1.10 0.10 1.30 0.10 1.50 0.10 1.55 0.10 1.60 0.20 1.70 0.15 1.10 0.15 1.15 0.15 1.30 0.15 1.50 0.15 1.10 0.15 1.30 0.15 1.50 0.15 2.40 0.15 1.00 0.15 1.10 0.15 1.30 0.15 1.40 0.15 4,000 0 0 0 0 0 4,000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 15,000 0 0 0 0 0 10,000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 4,000 4,000 2,500 2,500 2,500 4,000 4,000 4,000 2,500 2,500 2,500 2,500 2,000 2,000 4,000 4,000 4,000 2,500 2,500 2,500 2,000 2,000 2,000 2,000 2,000 1,000 2,500 1,000 1,000 1,000 1,000 1,000 1,000 1,000 1,000 1,000 1,000 1,000 1,000 1,000 1,000 500 1,000 1,000 1,000 1,000 0 10,000 10,000 10,000 10,000 10,000 10,000 10,000 10,000 10,000 10,000 10,000 10,000 8,000 8,000 10,000 10,000 10,000 10,000 10,000 10,000 8,000 8,000 8,000 8,000 8,000 4,000 10,000 4,000 4,000 4,000 4,000 4,000 4,000 4,000 4,000 4,000 4,000 4,000 4,000 4,000 4,000 2,000 4,000 4,000 4,000 4,000 Thickness Code Case Size1 Thickness Range (mm) 7" Reel 13" Reel 7" Reel 13" Reel Paper Quantity1 Plastic Quantity Package quantity based on finished chip thickness specifications. 1 If ordering using the 2 mm Tape and Reel pitch option, the packaging quantity outlined in the table above will be doubled. This option is limited to EIA 0603 (1608 metric) case size devices. For more information regarding 2 mm pitch option see "Tape & Reel Packaging Information". (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 * 864-963-6300 * www.kemet.com C1013_X7R_FT-CAP_SMD * 3/21/2017 10 Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs) Flexible Termination System (FT-CAP), X7R Dielectric, 6.3 - 250 VDC (Commercial Grade) Table 2B - Bulk Packaging Quantities Loose Packaging Packaging Type Bulk Bag (default) Packaging C-Spec1 N/A 2 Case Size Packaging Quantities (pieces/unit packaging) EIA (in) Metric (mm) 0402 0603 0805 1206 1210 1808 1005 1608 2012 3216 3225 4520 1812 1825 2220 2225 4532 4564 5650 5664 Minimum Maximum 50,000 1 20,000 The "Packaging C-Spec" is a 4 to 8 digit code which identifies the packaging type and/or product grade. When ordering, the proper code must be included in the 15th through 22nd character positions of the ordering code. See "Ordering Information" section of this document for further details. Commercial Grade product ordered without a packaging C-Spec will default to our standard "Bulk Bag" packaging. Contact KEMET if you require a bulk bag packaging option for Automotive Grade products. 2 A packaging C-Spec (see note 1 above) is not required for "Bulk Bag" packaging (excluding Anti-Static Bulk Bag and Automotive Grade products). The 15th through 22nd character positions of the ordering code should be left blank. All product ordered without a packaging C-Spec will default to our standard "Bulk Bag" packaging. 1 (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 * 864-963-6300 * www.kemet.com C1013_X7R_FT-CAP_SMD * 3/21/2017 11 Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs) Flexible Termination System (FT-CAP), X7R Dielectric, 6.3 - 250 VDC (Commercial Grade) Table 3 - Chip Capacitor Land Pattern Design Recommendations per IPC-7351 EIA Size Code Metric Size Code 0603 Density Level A: Maximum (Most) Land Protrusion (mm) Density Level B: Median (Nominal) Land Protrusion (mm) Density Level C: Minimum (Least) Land Protrusion (mm) C Y X V1 V2 C Y X V1 V2 C Y X V1 V2 1608 0.85 1.25 1.10 4.00 2.10 0.75 1.05 1.00 3.10 1.50 0.65 0.85 0.90 2.40 1.20 0805 2012 0.99 1.44 1.66 4.47 2.71 0.89 1.24 1.56 3.57 2.11 0.79 1.04 1.46 2.42 1.81 1206 3216 1.59 1.62 2.06 5.85 3.06 1.49 1.42 1.96 4.95 2.46 1.39 1.22 1.86 4.25 2.16 1210 3225 1.59 1.62 3.01 5.90 4.01 1.49 1.42 2.91 4.95 3.41 1.39 1.22 2.81 4.25 3.11 1808 4520 2.30 1.75 2.30 7.40 3.30 2.20 1.55 2.20 6.50 2.70 2.10 1.35 2.10 5.80 2.40 1812 4532 2.10 1.80 3.60 7.00 4.60 2.00 1.60 3.50 6.10 4.00 1.90 1.40 3.40 5.40 3.70 1825 4564 2.15 1.80 6.90 7.10 7.90 2.05 1.60 6.80 6.20 7.30 1.95 1.40 6.70 5.50 7.00 2220 5650 2.85 2.10 5.50 8.80 6.50 2.75 1.90 5.40 7.90 5.90 2.65 1.70 5.30 7.20 5.60 2225 5664 2.85 2.10 6.90 8.80 7.90 2.75 1.90 6.80 7.90 7.30 2.65 1.70 6.70 7.20 7.00 Density Level A: For low-density product applications. Recommended for wave solder applications and provides a wider process window for reflow solder processes. KEMET only recommends wave soldering of EIA 0603, 0805, and 1206 case sizes. Density Level B: For products with a moderate level of component density. Provides a robust solder attachment condition for reflow solder processes. Density Level C: For high component density product applications. Before adapting the minimum land pattern variations the user should perform qualification testing based on the conditions outlined in IPC Standard 7351 (IPC-7351). Image below based on Density Level B for an EIA 1210 case size. V1 Y Y X C V2 X C Grid Placement Courtyard (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 * 864-963-6300 * www.kemet.com C1013_X7R_FT-CAP_SMD * 3/21/2017 12 Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs) Flexible Termination System (FT-CAP), X7R Dielectric, 6.3 - 250 VDC (Commercial Grade) Soldering Process Recommended Soldering Technique: * Solder wave or solder reflow for EIA case sizes 0603, 0805 and 1206 * All other EIA case sizes are limited to solder reflow only Recommended Reflow Soldering Profile: KEMET's families of surface mount multilayer ceramic capacitors (SMD MLCCs) are compatible with wave (single or dual), convection, IR or vapor phase reflow techniques. Preheating of these components is recommended to avoid extreme thermal stress. KEMET's recommended profile conditions for convection and IR reflow reflect the profile conditions of the IPC/ J-STD-020 standard for moisture sensitivity testing. These devices can safely withstand a maximum of three reflow passes at these conditions. Preheat/Soak Temperature Minimum (TSmin) Temperature Maximum (TSmax) Time (tS) from TSmin to TSmax Termination Finish SnPb TP 100% Matte Sn Ramp-Up Rate (TL to TP) 100C 150C 60 - 120 seconds 3C/second maximum 150C 200C 60 - 120 seconds 3C/second maximum Liquidous Temperature (TL) 183C 217C Time Above Liquidous (tL) 60 - 150 seconds 60 - 150 seconds Peak Temperature (TP) 235C 260C TL Temperature Profile Feature tP Maximum Ramp Up Rate = 3C/sec Maximum Ramp Down Rate = 6C/sec tL Tsmax Tsmin 25 ts 25C to Peak Time Time Within 5C of Maximum Peak Temperature (tP) 20 seconds 30 seconds maximum maximum 6C/second 6C/second Ramp-Down Rate (TP to TL) maximum maximum Time 25C to Peak 6 minutes 8 minutes Temperature maximum maximum Note 1: All temperatures refer to the center of the package, measured on the capacitor body surface that is facing up during assembly reflow. (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 * 864-963-6300 * www.kemet.com C1013_X7R_FT-CAP_SMD * 3/21/2017 13 Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs) Flexible Termination System (FT-CAP), X7R Dielectric, 6.3 - 250 VDC (Commercial Grade) Table 4 - Performance & Reliability: Test Methods and Conditions Stress Reference Test or Inspection Method Terminal Strength JIS-C-6429 Appendix 1, Note: Force of 1.8 kg for 60 seconds. Board Flex JIS-C-6429 Appendix 2, Note: Standard termination system - 2.0 mm (minimum) for all except 3 mm for C0G. Flexible termination system - 3.0 mm (minimum). Magnification 50 X. Conditions: Solderability J-STD-002 a) Method B, 4 hours at 155C, dry heat at 235C b) Method B at 215C category 3 c) Method D, category 3 at 260C Temperature Cycling JESD22 Method JA-104 Biased Humidity MIL-STD-202 Method 103 Moisture Resistance Thermal Shock High Temperature Life Storage Life Vibration Mechanical Shock Resistance to Solvents MIL-STD-202 Method 106 MIL-STD-202 Method 107 MIL-STD-202 Method 108 /EIA-198 MIL-STD-202 Method 108 MIL-STD-202 Method 204 MIL-STD-202 Method 213 MIL-STD-202 Method 215 1,000 Cycles (-55C to +125C). Measurement at 24 hours +/- 4 hours after test conclusion. Load Humidity: 1,000 hours 85C/85% RH and rated voltage. Add 100 K ohm resistor. Measurement at 24 hours +/- 4 hours after test conclusion. Low Volt Humidity: 1,000 hours 85C/85% RH and 1.5 V. Add 100 K ohm resistor. Measurement at 24 hours +/- 4 hours after test conclusion. t = 24 hours/cycle. Steps 7a and 7b not required. Measurement at 24 hours +/- 4 hours after test conclusion. -55C/+125C. Note: Number of cycles required - 300, maximum transfer time - 20 seconds, dwell time - 15 minutes. Air - Air. 1,000 hours at 125C (85C for X5R, Z5U and Y5V) with 2 X rated voltage applied. 150C, 0 VDC for 1,000 hours. 5 g's for 20 min., 12 cycles each of 3 orientations. Note: Use 8" X 5" PCB 0.031" thick 7 secure points on one long side and 2 secure points at corners of opposite sides. Parts mounted within 2" from any secure point. Test from 10 - 2,000 Hz Figure 1 of Method 213, Condition F. Add aqueous wash chemical, OKEM Clean or equivalent. Storage and Handling Ceramic chip capacitors should be stored in normal working environments. While the chips themselves are quite robust in other environments, solderability will be degraded by exposure to high temperatures, high humidity, corrosive atmospheres, and long term storage. In addition, packaging materials will be degraded by high temperature-reels may soften or warp and tape peel force may increase. KEMET recommends that maximum storage temperature not exceed 40C and maximum storage humidity not exceed 70% relative humidity. Temperature fluctuations should be minimized to avoid condensation on the parts and atmospheres should be free of chlorine and sulfur bearing compounds. For optimized solderability chip stock should be used promptly, preferably within 1.5 years of receipt. (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 * 864-963-6300 * www.kemet.com C1013_X7R_FT-CAP_SMD * 3/21/2017 14 Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs) Flexible Termination System (FT-CAP), X7R Dielectric, 6.3 - 250 VDC (Commercial Grade) Construction Detailed Cross Section Dielectric Material (BaTiO3) Barrier Layer End Termination/ (Ni) External Electrode Termination Finish (Cu) (100% Matte Sn / Epoxy Layer SnPb - 5% Pb min) (Ag) Dielectric Material (BaTiO3) Inner Electrodes (Ni) End Termination/ External Electrode (Cu) Epoxy Layer (Ag) Barrier Layer (Ni) Inner Electrodes (Ni) (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 * 864-963-6300 * www.kemet.com Termination Finish (100% Matte Sn / SnPb - 5% Pb min) C1013_X7R_FT-CAP_SMD * 3/21/2017 15 Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs) Flexible Termination System (FT-CAP), X7R Dielectric, 6.3 - 250 VDC (Commercial Grade) Capacitor Marking (Optional): These surface mount multilayer ceramic capacitors are normally supplied unmarked. If required, they can be marked as an extra cost option. Marking is available on most KEMET devices but must be requested using the correct ordering code identifier(s). If this option is requested, two sides of the ceramic body will be laser marked with a "K" to identify KEMET, followed by two characters (per EIA-198 - see table below) to identify the capacitance value. EIA 0603 case size devices are limited to the "K" character only. Laser marking option is not available on: * C0G, Ultra Stable X8R and Y5V dielectric devices * EIA 0402 case size devices * EIA 0603 case size devices with Flexible Termination option. * KPS Commercial and Automotive Grade stacked devices. EIA Case Size Metric Size Code Capacitance 0603 0805 1206 1210 1808 1812 1825 2220 2225 1608 2012 3216 3225 4520 4532 4564 5650 5664 170 pF 150 pF 910 pF 2,000 pF 3,900 pF 6,700 pF 0.018 F 0.027 F 0.033 F * X7R dielectric products in capacitance values outlined below Marking appears in legible contrast. Illustrated below is an example of an MLCC with laser marking of "KA8", which designates a KEMET device with rated capacitance of 100 F. Orientation of marking is vendor optional. KEMET ID (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 * 864-963-6300 * www.kemet.com 2-Digit Capacitance Code C1013_X7R_FT-CAP_SMD * 3/21/2017 16 Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs) Flexible Termination System (FT-CAP), X7R Dielectric, 6.3 - 250 VDC (Commercial Grade) Capacitor Marking (Optional) cont'd Alpha Character Capacitance (pF) For Various Alpha/Numeral Identifiers Numeral 9 0 1 2 3 4 5 6 7 8 100,000,000 Capacitance (pF) A 0.1 10 10 100 1,000 10,000 100,000 1,000,000 10,000,000 B 0.11 1.1 11 110 1,100 11,000 110,000 1,100,000 11,000,000 110,000,000 C 0.12 12 12 120 1,200 12,000 120,000 1,200,000 12,000,000 120,000,000 D 0.13 13 13 130 1,300 13,000 130,000 1,300,000 13,000,000 130,000,000 E 0.15 15 15 150 1,500 15,000 150,000 1,500,000 15,000,000 150,000,000 160,000,000 F 0.16 16 16 160 1,600 16,000 160,000 1,600,000 16,000,000 G 0.18 18 18 180 1,800 18,000 180,000 1,800,000 18,000,000 180,000,000 H 0.2 20 20 200 2,000 20,000 200,000 2,000,000 20,000,000 200,000,000 J 0.22 22 22 220 2,200 22,000 220,000 2,200,000 22,000,000 220,000,000 K 0.24 2.4 24 240 2,400 24,000 240,000 2,400,000 24,000,000 240,000,000 L 0.27 2.7 27 270 2,700 27,000 270,000 2,700,000 27,000,000 270,000,000 M 0.3 30 30 300 3,000 30,000 300,000 3,000,000 30,000,000 300,000,000 N 0.33 33 33 330 3,300 33,000 330,000 3,300,000 33,000,000 330,000,000 P 0.36 36 36 360 3,600 36,000 360,000 3,600,000 36,000,000 360,000,000 Q 0.39 39 39 390 3,900 39,000 390,000 3,900,000 39,000,000 390,000,000 R 0.43 43 43 430 4,300 43,000 430,000 4,300,000 43,000,000 430,000,000 470,000,000 S 0.47 4.7 47 470 4,700 47,000 470,000 4,700,000 47,000,000 T 0.51 5.1 51 510 5,100 51,000 510,000 5,100,000 51,000,000 510,000,000 U 0.56 56 56 560 5,600 56,000 560,000 5,600,000 56,000,000 560,000,000 V 0.62 62 62 620 6,200 62,000 620,000 6,200,000 62,000,000 620,000,000 W 0.68 68 68 680 6,800 68,000 680,000 6,800,000 68,000,000 680,000,000 X 0.75 75 75 750 7,500 75,000 750,000 7,500,000 75,000,000 750,000,000 Y 0.82 82 82 820 8,200 82,000 820,000 8,200,000 82,000,000 820,000,000 Z 0.91 9.1 91 910 9,100 91,000 910,000 9,100,000 91,000,000 910,000,000 a 0.25 25 25 250 2,500 25,000 250,000 2,500,000 25,000,000 250,000,000 b 0.35 35 35 350 3,500 35,000 350,000 3,500,000 35,000,000 350,000,000 d 0.4 40 40 400 4,000 40,000 400,000 4,000,000 40,000,000 400,000,000 e 0.45 45 45 450 4,500 45,000 450,000 4,500,000 45,000,000 450,000,000 f 0.5 50 50 500 5,000 50,000 500,000 5,000,000 50,000,000 500,000,000 m 0.6 60 60 600 6,000 60,000 600,000 6,000,000 60,000,000 600,000,000 n 0.7 70 70 700 7,000 70,000 700,000 7,000,000 70,000,000 700,000,000 t 0.8 80 80 800 8,000 80,000 800,000 8,000,000 80,000,000 800,000,000 y 0.9 90 90 900 9,000 90,000 900,000 9,000,000 90,000,000 900,000,000 (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 * 864-963-6300 * www.kemet.com C1013_X7R_FT-CAP_SMD * 3/21/2017 17 Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs) Flexible Termination System (FT-CAP), X7R Dielectric, 6.3 - 250 VDC (Commercial Grade) Tape & Reel Packaging Information KEMET offers multilayer ceramic chip capacitors packaged in 8, 12 and 16 mm tape on 7" and 13" reels in accordance with EIA Standard 481. This packaging system is compatible with all tape-fed automatic pick and place systems. See Table 2 for details on reeling quantities for commercial chips. Bar Code Label Anti-Static Reel (R) Embossed Plastic* or Punched Paper Carrier. ET KEM Chip and KPS Orientation in Pocket (except 1825 Commercial, and 1825 and 2225 Military) Sprocket Holes Embossment or Punched Cavity 8 mm, 12 mm or 16 mm Carrier Tape 178 mm (7.00") or 330 mm (13.00") Anti-Static Cover Tape (.10 mm (.004") Maximum Thickness) *EIA 01005, 0201, 0402 and 0603 case sizes available on punched paper carrier only. Table 5 - Carrier Tape Configuration, Embossed Plastic & Punched Paper (mm) EIA Case Size Tape Size (W)* Embossed Plastic 7" Reel 13" Reel Pitch (P1)* Punched Paper 7" Reel 13" Reel Pitch (P1)* 01005 - 0402 8 2 2 0603 8 2/4 2/4 0805 8 4 4 4 4 1206 - 1210 8 4 4 4 4 1805 - 1808 12 4 4 1812 12 8 8 KPS 1210 12 8 8 KPS 1812 & 2220 16 12 12 Array 0508 & 0612 8 4 4 *Refer to Figures 1 & 2 for W and P1 carrier tape reference locations. *Refer to Tables 6 & 7 for tolerance specifications. New 2 mm Pitch Reel Options* Packaging Ordering Code (C-Spec) Packaging Type/Options C-3190 C-3191 C-7081 C-7082 Automotive grade 7" reel unmarked Automotive grade 13" reel unmarked Commercial grade 7" reel unmarked Commercial grade 13" reel unmarked * 2 mm pitch reel only available for 0603 EIA case size. 2 mm pitch reel for 0805 EIA case size under development. Benefits of Changing from 4 mm to 2 mm Pitching Spacing * Lower placement costs * Double the parts on each reel results in fewer reel changes and increased efficiency * Fewer reels result in lower packaging, shipping and storage costs, reducing waste (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 * 864-963-6300 * www.kemet.com C1013_X7R_FT-CAP_SMD * 3/21/2017 18 Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs) Flexible Termination System (FT-CAP), X7R Dielectric, 6.3 - 250 VDC (Commercial Grade) Figure 1 - Embossed (Plastic) Carrier Tape Dimensions P2 T T2 ODo [10 pitches cumulative tolerance on tape 0.2 mm] Po E1 Ao F Ko B1 E2 Bo S1 W P1 T1 Center Lines of Cavity OD Cover Tape B 1 is for tape feeder reference only, including draft concentric about B o. 1 Embossment For cavity size, see Note 1 Table 4 User Direction of Unreeling Table 6 - Embossed (Plastic) Carrier Tape Dimensions Metric will govern Constant Dimensions -- Millimeters (Inches) Tape Size D0 8 mm 12 mm 1.5 +0.10/-0.0 (0.059 +0.004/0.0) 16 mm D1 Minimum Note 1 1.0 (0.039) 1.5 (0.059) R Reference S1 Minimum T Note 2 Note 3 Maximum 25.0 (0.984) 1.75 0.10 4.0 0.10 2.0 0.05 0.600 0.600 (0.069 0.004) (0.157 0.004) (0.079 0.002) (0.024) (0.024) 30 (1.181) E1 P0 P2 T1 Maximum 0.100 (0.004) Variable Dimensions -- Millimeters (Inches) Tape Size Pitch 8 mm Single (4 mm) 12 mm Single (4 mm) & Double (8 mm) 16 mm Triple (12 mm) B1 Maximum Note 4 4.35 (0.171) 8.2 (0.323) 12.1 (0.476) E2 Minimum 6.25 (0.246) 10.25 (0.404) 14.25 (0.561) F P1 3.5 0.05 4.0 0.10 (0.138 0.002) (0.157 0.004) 5.5 0.05 8.0 0.10 (0.217 0.002) (0.315 0.004) 7.5 0.05 12.0 0.10 (0.138 0.002) (0.157 0.004) T2 Maximum 2.5 (0.098) 4.6 (0.181) 4.6 (0.181) W Maximum 8.3 (0.327) 12.3 (0.484) 16.3 (0.642) A0,B0 & K0 Note 5 1. The embossment hole location shall be measured from the sprocket hole controlling the location of the embossment. Dimensions of embossment location and hole location shall be applied independent of each other. 2. The tape with or without components shall pass around R without damage (see Figure 6). 3. If S1 < 1.0 mm, there may not be enough area for cover tape to be properly applied (see EIA Standard 481 paragraph 4.3 section b). 4. B1 dimension is a reference dimension for tape feeder clearance only. 5. The cavity defined by A0, B0 and K0 shall surround the component with sufficient clearance that: (a) the component does not protrude above the top surface of the carrier tape. (b) the component can be removed from the cavity in a vertical direction without mechanical restriction, after the top cover tape has been removed. (c) rotation of the component is limited to 20 maximum for 8 and 12 mm tapes and 10 maximum for 16 mm tapes (see Figure 3). (d) lateral movement of the component is restricted to 0.5 mm maximum for 8 and 12 mm wide tape and to 1.0 mm maximum for 16 mm tape (see Figure 4). (e) for KPS Series product, A0 and B0 are measured on a plane 0.3 mm above the bottom of the pocket. (f) see Addendum in EIA Standard 481 for standards relating to more precise taping requirements. (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 * 864-963-6300 * www.kemet.com C1013_X7R_FT-CAP_SMD * 3/21/2017 19 Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs) Flexible Termination System (FT-CAP), X7R Dielectric, 6.3 - 250 VDC (Commercial Grade) Figure 2 - Punched (Paper) Carrier Tape Dimensions T Po ODo [10 pitches cumulative tolerance on tape 0.2 mm] A0 F P1 T1 T1 Top Cover Tape W E2 B0 Bottom Cover Tape E1 G Cavity Size, See Note 1, Table 7 Center Lines of Cavity Bottom Cover Tape User Direction of Unreeling Table 7 - Punched (Paper) Carrier Tape Dimensions Metric will govern Constant Dimensions -- Millimeters (Inches) Tape Size D0 E1 P0 P2 T1 Maximum G Minimum 8 mm 1.5 +0.10 -0.0 (0.059 +0.004 -0.0) 1.75 0.10 (0.069 0.004) 4.0 0.10 (0.157 0.004) 2.0 0.05 (0.079 0.002) 0.10 (0.004) Maximum R Reference Note 2 0.75 (0.030) 25 (0.984) Variable Dimensions -- Millimeters (Inches) Tape Size Pitch 8 mm Half (2 mm) 8 mm Single (4 mm) E2 Minimum F P1 T Maximum W Maximum A0 B 0 6.25 (0.246) 3.5 0.05 (0.138 0.002) 2.0 0.05 (0.079 0.002) 4.0 0.10 (0.157 0.004) 1.1 (0.098) 8.3 (0.327) 8.3 (0.327) Note 1 1. The cavity defined by A0, B0 and T shall surround the component with sufficient clearance that: a) the component does not protrude beyond either surface of the carrier tape. b) the component can be removed from the cavity in a vertical direction without mechanical restriction, after the top cover tape has been removed. c) rotation of the component is limited to 20 maximum (see Figure 3). d) lateral movement of the component is restricted to 0.5 mm maximum (see Figure 4). e) see Addendum in EIA Standard 481 for standards relating to more precise taping requirements. 2. The tape with or without components shall pass around R without damage (see Figure 6). (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 * 864-963-6300 * www.kemet.com C1013_X7R_FT-CAP_SMD * 3/21/2017 20 Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs) Flexible Termination System (FT-CAP), X7R Dielectric, 6.3 - 250 VDC (Commercial Grade) Packaging Information Performance Notes 1. Cover Tape Break Force: 1.0 Kg minimum. 2. Cover Tape Peel Strength: The total peel strength of the cover tape from the carrier tape shall be: Tape Width Peel Strength 8 mm 0.1 to 1.0 Newton (10 to 100 gf) 12 and 16 mm 0.1 to 1.3 Newton (10 to 130 gf) The direction of the pull shall be opposite the direction of the carrier tape travel. The pull angle of the carrier tape shall be 165 to 180 from the plane of the carrier tape. During peeling, the carrier and/or cover tape shall be pulled at a velocity of 300 10 mm/minute. 3. Labeling: Bar code labeling (standard or custom) shall be on the side of the reel opposite the sprocket holes. Refer to EIA Standards 556 and 624. Figure 3 - Maximum Component Rotation T Maximum Component Rotation Top View Maximum Component Rotation Side View Typical Pocket Centerline Tape Maximum Width (mm) Rotation ( 8,12 20 16 - 200 10 Bo T) Typical Component Centerline Ao Figure 4 - Maximum Lateral Movement 8 mm & 12 mm Tape 0.5 mm maximum 0.5 mm maximum s Tape Width (mm) 8,12 16 - 56 72 - 200 Maximum Rotation ( 20 10 5 Figure 5 - Bending Radius Embossed Carrier 16 mm Tape S) Punched Carrier 1.0 mm maximum 1.0 mm maximum R (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 * 864-963-6300 * www.kemet.com Bending Radius R C1013_X7R_FT-CAP_SMD * 3/21/2017 21 Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs) Flexible Termination System (FT-CAP), X7R Dielectric, 6.3 - 250 VDC (Commercial Grade) Figure 6 - Reel Dimensions Full Radius, See Note W3 (Includes flange distortion at outer edge) Access Hole at Slot Location (O 40 mm minimum) W2 D A (See Note) N C (Arbor hole diameter) B (see Note) (Measured at hub) W1 (Measured at hub) If present, tape slot in core for tape start: 2.5 mm minimum width x 10.0 mm minimum depth Note: Drive spokes optional; if used, dimensions B and D shall apply. Table 8 - Reel Dimensions Metric will govern Constant Dimensions -- Millimeters (Inches) Tape Size A B Minimum C D Minimum 8 mm 178 0.20 (7.008 0.008) or 330 0.20 (13.000 0.008) 1.5 (0.059) 13.0 +0.5/-0.2 (0.521 +0.02/-0.008) 20.2 (0.795) 12 mm 16 mm Variable Dimensions -- Millimeters (Inches) Tape Size N Minimum W1 W2 Maximum W3 50 (1.969) 8.4 +1.5/-0.0 (0.331 +0.059/-0.0) 12.4 +2.0/-0.0 (0.488 +0.078/-0.0) 16.4 +2.0/-0.0 (0.646 +0.078/-0.0) 14.4 (0.567) 18.4 (0.724) 22.4 (0.882) Shall accommodate tape width without interference 8 mm 12 mm 16 mm (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 * 864-963-6300 * www.kemet.com C1013_X7R_FT-CAP_SMD * 3/21/2017 22 Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs) Flexible Termination System (FT-CAP), X7R Dielectric, 6.3 - 250 VDC (Commercial Grade) Figure 7 - Tape Leader & Trailer Dimensions Embossed Carrier Carrier Tape Punched Carrier 8 mm & 12 mm only END Round Sprocket Holes START Top Cover Tape Elongated Sprocket Holes (32 mm tape and wider) Trailer 160 mm Minimum Components 100 mm Minimum Leader 400 mm Minimum Top Cover Tape Figure 8 - Maximum Camber Elongated sprocket holes (32 mm & wider tapes) Carrier Tape Round Sprocket Holes 1 mm Maximum, either direction Straight Edge 250 mm (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 * 864-963-6300 * www.kemet.com C1013_X7R_FT-CAP_SMD * 3/21/2017 23 Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs) Flexible Termination System (FT-CAP), X7R Dielectric, 6.3 - 250 VDC (Commercial Grade) KEMET Electronic Corporation Sales Offices For a complete list of our global sales offices, please visit www.kemet.com/sales. Disclaimer All product specifications, statements, information and data (collectively, the "Information") in this datasheet are subject to change. The customer is responsible for checking and verifying the extent to which the Information contained in this publication is applicable to an order at the time the order is placed. All Information given herein is believed to be accurate and reliable, but it is presented without guarantee, warranty, or responsibility of any kind, expressed or implied. Statements of suitability for certain applications are based on KEMET Electronics Corporation's ("KEMET") knowledge of typical operating conditions for such applications, but are not intended to constitute - and KEMET specifically disclaims - any warranty concerning suitability for a specific customer application or use. The Information is intended for use only by customers who have the requisite experience and capability to determine the correct products for their application. Any technical advice inferred from this Information or otherwise provided by KEMET with reference to the use of KEMET's products is given gratis, and KEMET assumes no obligation or liability for the advice given or results obtained. Although KEMET designs and manufactures its products to the most stringent quality and safety standards, given the current state of the art, isolated component failures may still occur. Accordingly, customer applications which require a high degree of reliability or safety should employ suitable designs or other safeguards (such as installation of protective circuitry or redundancies) in order to ensure that the failure of an electrical component does not result in a risk of personal injury or property damage. Although all product-related warnings, cautions and notes must be observed, the customer should not assume that all safety measures are indicted or that other measures may not be required. KEMET is a registered trademark of KEMET Electronics Corporation. (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 * 864-963-6300 * www.kemet.com C1013_X7R_FT-CAP_SMD * 3/21/2017 24 Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Kemet: C1206X104K5RAC C1206X474K1RACTU C1206X106K8RACTU C1206X104K5RACTU C0805X103K2RACTU C1206X104K2RACTU C1206X473J5RACTU C0805X104K5RACTU C0805X153K1RACTU C0805X223K2RACTU C0805X333K5RACTU C0805X472K2RACTU C0805X473K1RACTU C1206X473K2RACTU C1206X225K5RACTU C0805X334K5RACTU C1206X475M3RACTU C1206X475K3RACTU C1206X102KBRACTU C1206X562JCRACTU C1206X103KCRACTU C1206X103KBRACTU C1206X102KGRACTU C1206X102KDRACTU C1206X102KCRACTU C0805X474M9RALTU C0805X561J1RAL7210 C0805X561J1RALTU C0805X561J2RAL7210 C0805X561J2RALTU C0805X561J3RAL7210 C0805X561J3RALTU C0805X561J4RAL7210 C0805X561J4RALTU C0805X561J5RAL7210 C0805X561J5RALTU C0805X561J8RAL7210 C0805X561J8RALTU C0805X561J9RAL7210 C0805X561J9RALTU C0805X561K1RAL7210 C0805X561K1RALTU C0805X561K2RAL7210 C0805X561K2RALTU C0805X561K3RAL7210 C0805X561K3RALTU C0805X561K4RAL7210 C0805X561K4RALTU C0805X561K5RAL7210 C0805X561K5RALTU C0805X561K8RAL7210 C0805X561K8RALTU C0805X561K9RAL7210 C0805X561K9RALTU C0805X561M1RAL7210 C0805X561M1RALTU C0805X561M2RAL7210 C0805X561M2RALTU C0805X561M3RAL7210 C0805X561M3RALTU C0805X561M4RAL7210 C0805X561M4RALTU C0805X561M5RAL7210 C0805X561M5RALTU C0805X561M8RAL7210 C0805X561M8RALTU C0805X561M9RAL7210 C0805X561M9RALTU C0805X562J1RAL7210 C0805X562J1RALTU C0805X562J2RAL7210 C0805X562J2RALTU C0805X562J3RAL7210 C0805X562J3RALTU C0805X562J4RAL7210 C0805X562J4RALTU C0805X562J5RAL7210 C0805X562J5RALTU C0805X562J8RAL7210 C0805X562J8RALTU C0805X562J9RAL7210 C0805X562J9RALTU C0805X562K1RAL7210 C0805X562K1RALTU C0805X562K2RAL7210 C0805X562K2RALTU C0805X562K3RAL7210 C0805X562K3RALTU C0805X562K4RAL7210 C0805X562K4RALTU C0805X562K5RAL7210 C0805X562K5RALTU C0805X562K8RAL7210 C0805X562K8RALTU C0805X562K9RAL7210 C0805X562K9RALTU C0805X562M1RAL7210 C0805X562M1RALTU C0805X562M2RAL7210 C0805X562M2RALTU