P
RODUCTION
D
ATASHEET
Microsemi
Integrated Products
11861 Western Avenue, Garden Grove, CA. 92841, 714-898-8121, Fax: 714-893-2570
Page 1
Copyright © 2002
Rev. 1.0, 2006-03-10
WWW.Microsemi .COM
PanelMatch™ LXMG1617-05-2x
5V 2.2W CCFL Programmable Inverter Module
TM ®
DESCRIPTION
The LXMG1617-05-2x is a Single
Output 2.2W Direct Drive™ CCFL (Cold
Cathode Fluorescent Lamp) Inverter
Module specifically designed for driving
LCD backlight lamps. It is ideal for
driving typical 3.9” to 6.4” TFT panels.
LXMG1617 modules provide the
designer with a vastly superior display
brightness range. This brightness range is
achievable wit h vi rt uall y any LC D di spl ay .
The maximum output current is
externally programmable over a range of
3.5 to 5mA in 0.5mA steps to allow the
inverter to properly match to a wide array
of LCD panel lamp current specifications.
The modules include a dimming input that
permits brightness control from a dc
voltage source, a PWM signal or an
external potentiometer.
RangeMAX™ Digital Dimming
Technique provides flicker-free brightness
control in any wide range typically (50:1+)
dimming application.
The resultant “burst drive” that
energizes the lamp was designed
specifically to ensure that no premature
lamp degradation occurs, while allowing
significant power savings at lower dim
levels.
The modules convert DC voltage from
the system battery or AC adapter directly
to high frequency, high-voltage waves
required to ignite and operate CCFL
lamps. A 3.3V input inverter is also
available (LXMG1617-03-2x).
The modules design is based on
Microsemi’s new LX1689 backlight
controller, which provides a number of
cost and performance advantages due to
the controller’s high level of integration.
Other benefits of this new topology
are stable fixed-frequency operation,
secondary-side strike-voltage regulation
and both open/shorted lamp protection
with fault timeout.
IMPORTANT: For the most current data, co nsult MICROSEMI’s website: http://www.microsemi.com
Protected By U.S. Patents: 5,923,129; 5,930, 121; 6,198,234; Patents Pending
KEY FEATURES
Externally Programmable
Maximum Output Current
Easy to Use Brightness
Control
Output Short-Circuit Protection
and Automatic Strike-Voltage
Regulation and Timeout
RangeMAX Wide Range
Dimming
Fixed Frequency Operation
Rated From -20 to 70°C
UL60950 Pending
RoHS Compliant
APPLICATIONS
PDA’s
Portable Instrumentation
Industrial Display Controls
BENEFITS
Smooth, Flicker Free 2%-
100% Full-Range Brightness
Control
Programmable output current
allows inverter to mate with a
wide variety of LCD panel’s
specifications
Output Open Circuit Voltage
Regulation Minimizes Corona
Discharge For High Reliability
PRODUCT HIGHLIGHT
U
NIVERSAL DIMMING
I
NPUT
"PWM", VDC, OR POTENTIOMETER
DC Voltage
Source Potentiometer PWM
Signal
SELECTABLE MAXIMUM OUPUT
CURRENT 3.5MA TO 5MARMS
123
W
PACKAGE ORDER INFO
PART NUMBER OUTPUT CONNECTOR INVERTER MATES DIRECTLY TO
PANEL CONNECTORS
LXMG1617-05-21 JST SM02(8.0)B-BHS-1-TB (LF)(SN) or Yeon Ho 20015WR-05A00 JST BHR-03VS-1
LXMG1617-05-22 JST SM02B-BHSS-1-TB (LF)(SN) or Yeon Ho 35001WR-02A00 JST BHSR-02VS-1
L
LX
XM
MG
G1
16
61
17
7-
-0
05
5
P
RODUCTION
D
ATASHEET
Microsemi
Integrated Products
11861 Western Avenue, Garden Grove, CA. 92841, 714-898-8121, Fax: 714-893-2570
Page 2
Copyright © 2002
Rev. 1.0, 2006-03-10
WWW.Microsemi .COM
PanelMatch™ LXMG1617-05-2x
5V 2.2W CCFL Programmable Inverter Module
TM ®
ABSOLUTE MAXIMUM RATINGS (NOTE 1)
Input Signal Voltage (VIN1)....................................................................................................................................-0.3V to 6.5V
Input Power ...................................................................................................................................................................... 3.0W
Output Voltage, no load ............................................................................................................ Internally Limited to 1300VRMS
Output Current ...............................................................................................................................6mARMS (Internally Limited)
Output Power ................................................................................................................................................................... 2.3W
Input Signal Voltage ( SLEEP Input)....................................................................................................................-0.3V to 5.5V
Input Signal Voltage (BRITE) ...............................................................................................................................-0.3V to 5.5V
Ambient Operating Temperature, zero airflow.....................................................................................................-20°C to 70°C
Storage Temperature Range...............................................................................................................................-40°C to 85°C
Note 1: Exceeding these ratings could cause damage to the device. All voltages are with respect to Ground. Currents are positive into, negative out of specified
terminal.
RECOMMENDED OPERATING CONDITIONS (R.C.)
This module has been designed to operate over a wide range of input and output conditions. However, best efficiency and performance
will be obtained if the module is operated under the condition listed in the ‘R.C.’ column. Min. and Max. columns indicate values beyond
which the inverter, although operational, will not function optimally.
Recommended Operating Conditions
Parameter Symbol
Min R.C. Max Units
Input Supply Voltage Range (Fully Regulated
Lamp Current) 4.75 5 5.25
Input Supply Voltage Range (Functional)
VIN1
4.5 5 5.5
V
Output Power PO 2.2 W
Linear BRITE Control Input Voltage Range VBRT_ADJ 0.5 2.0 V
Lamp Operating Voltage VLAMP 325 380 435* VRMS
Lamp Current (Full Brightness) IOLAMP 3.5 5.0 mARMS
Operating Ambient Temperature Range TA -20 70 °C
* Total output power must not exceed 4W. Higher voltage lamps may require maximum output current to be set lower than 5mARMS
ELECTRICAL CHARACTERISTICS
Unless otherwise specified, the following specifications apply over the recommended operating condition and ambient temperature of
25°C except where otherwise noted.
LXMG1617-05-2x
Parameter Symbol Test Conditions Min Typ Max
Units
` OUTPUT PIN CHARACTERISTICS
Full Bright Lamp Current IL(MAX) VBRT_ADJ > 2.0VDC, SLEEP > 2.0V, VIN1 = 5VDC
ISET1 = Ground, ISET2 = Ground 3.0 3.5 4.0 mARMS
Full Bright Lamp Current IL(MAX) VBRT_ADJ > 2.0VDC, SLEEP > 2.0V, VIN1 = 5VDC
ISET1 = Ground, ISET2 = Open 3.5 4.0 4.5 mARMS
Full Bright Lamp Current IL(MAX) VBRT_ADJ > 2.0VDC, SLEEP > 2.0V, VIN1 = 5VDC
ISET1 = Open, ISET2 = Ground 4.0 4.5 5.0 mARMS
Full Bright Lamp Current IL(MAX) VBRT_ADJ > 2.0VDC, SLEEP > 2.0V, VIN1 = 5VDC
ISET1 = Open, ISET2 = Open 4.5 5 5.5 mARMS
Min. Average Lamp Current
IL(MIN) VBRT_ADJ ≤0.5VDC, SLEEP > 2.0V, VIN1 = 5VDC
ISET1 = ISET2 = Ground 0.21 mARMS
Lamp Start Voltage VLS -20°C < TA < 70°C, VIN1 > 4.5VDC 1000 1100 VRMS
Operating Frequency fO VBRT_ADJ = 2.5VDC, SLEEP > 2.0V, VIN1 = 5V 85 90 94 kHz
Burst Frequency fBURST Output Burst Frequency 166 176 184 Hz
E
EL
LE
EC
CT
TR
RI
IC
CA
AL
LS
S
P
RODUCTION
D
ATASHEET
Microsemi
Integrated Products
11861 Western Avenue, Garden Grove, CA. 92841, 714-898-8121, Fax: 714-893-2570
Page 3
Copyright © 2002
Rev. 1.0, 2006-03-10
WWW.Microsemi .COM
PanelMatch™ LXMG1617-05-2x
5V 2.2W CCFL Programmable Inverter Module
TM ®
ELECTRICAL CHARACTERISTICS (CONTINUED)
Unless otherwise specified, the following specifications apply over the recommended operating condition and ambient temperature of
25°C except where otherwise noted.
LXMG1617-05-2x
Parameter Symbol Test Conditions Min Typ Max
Units
` BRITE INPUT
VBRT_ADJ = 0VDC -300 µADC
Input Current IBRT VBRT_ADJ = 3VDC 50 µADC
Minimum Input for Max. Lamp Current VBRT_ADJ I
O(LAMP) = Maximum Lamp Current 2.0 2.05 VDC
Maximum Input for Min. Lamp Current VBRT_ADJ I
O(LAMP) = Minimum Lamp Current 0.4 0.5 VDC
` SLEEP INPUT
RUN Mode SLEEP
V 2.0 VIN1 V
DC
SLEEP Mode SLEEP
V -0.3 0.8 VDC
` SET1,2 INPUT
SET1,2 Low Threshold V
L 0.4 V
Input Current ISET V
SET ≤ 0.4V -300 µA
` POWER CHARACTERISTICS
Sleep Current IIN(MIN) VIN1 = 5VDC, SLEEP < 0.8V 0.0 4 10 µADC
Run Current IRUN VIN1 = 5VDC, SLEEP ≥ 2.0V, ISET1 = Open
ISET2 = Ground, VLAMP = 380VRMS 430 mADC
Efficiency η VIN1 = 5VDC, SLEEP ≥ 2.0V, ISET1 = Open
ISET2 = Ground, VLAMP = 380VRMS 80 %
FUNCTIONAL PIN DESCRIPTION
CONN PIN DESCRIPTION
CN1 (Molex 53261-0871) Mates with 51021-0800 housing, 50079-8100 pins. Mates with LX9501G input cable assembly
CN1-1
CN1-2 VIN1 Main Input Power Supply (4.75V < VIN1 < 5.25V)
CN1-3
CN1-4 GND Power Supply Return
CN1-5 SLEEP ON/OFF Control. (0V < SLEEP < 0.8 = OFF, SLEEP >= 2.0V = ON
CN1-6 BRITE Brightness Control (0.5V to 2.0VDC). 2.0VDC gives maximum lamp current.
CN1-7 SET1 SET1 MSB Connecting this pin to ground decreases the output current (see Table 1)
CN1-8 SET2 SET2 LSB Connecting this pin to ground decreases the output current (see Table 1)
CN2 for LXMG1617-05-21 and -22 (JST SM02(8.0)B-BHS-1-TB(LF)(SN) | Yeon Ho 20015WR-05A00 or
SM02B-BHSS-1-TB(LF)(SN) | 35001WR-02A00)
CN2-1 VHI High voltage connection to high side of lamp. Connect to lamp terminal with shortest lead length.
DO NOT connect to Ground.
CN2-2 VLO Connection to low side of lamp. Connect to lamp terminal with longer lead length.
DO NOT connect to Ground
E
EL
LE
EC
CT
TR
RI
IC
CA
AL
LS
S
P
RODUCTION
D
ATASHEET
Microsemi
Integrated Products
11861 Western Avenue, Garden Grove, CA. 92841, 714-898-8121, Fax: 714-893-2570
Page 4
Copyright © 2002
Rev. 1.0, 2006-03-10
WWW.Microsemi .COM
PanelMatch™ LXMG1617-05-2x
5V 2.2W CCFL Programmable Inverter Module
TM ®
TABLE 1 SETTING OUTPUT CURRENT
OUTPUT CURRENT SETTINGS
SET1
(Pin 7) SET2
(Pin 8) Nominal Output Current
Open* Open* 5.0mA
Open* Ground 4.5mA
Ground Open* 4.0mA
Ground Ground 3.5mA
* If driven by a logic signal it should be open collector or open drain only, not a voltage source.
PHYSICAL DIMENSIONS
LXMG1617-05-2X
0.8mm
0.0315in.
Weight: (5.7g) typ.
4.6mm Max
0.181in.
86mm
3.39in
CN1
CN2
W
11mm
0.433in.
3.5mm
0.138in.
16mm
0.63in.
71mm
2.80in
12.5mm
0.492in
X
PCB tolerances ± 0.5mm, M2 or 2-56 recommended mounting screws
Warning
High Voltage Present at
high side of transformer
and Output Connector
GROUNDED MOUNTING
HOLE 2.44MM ±0.08 DIA.
MOUNTING HOLE
2.44MM ±0.08 DIA.
60mm ±0.2mm
2.36in.
9mm ±2mm
0.354 in.
R1.0
All dimensions in millimeters, inches are for reference only.
SIMPLIFIED BLOCK DIAGRAM
Ramp
Gen
Transformer
Driver
0.5 -
2V DC
+
-
LAMP
VLO
VHI
Comparator
Ramp
VBRITE
SET 1
High Voltage
Transformer
ISENSE
OV SENSE
SET 2
+3V
10K
10K
+3V
+3V
VIN1
OC SENSE
10K
Controller
P
PA
AC
CK
KA
AG
GE
E
D
DA
AT
TA
A
P
RODUCTION
D
ATASHEET
Microsemi
Integrated Products
11861 Western Avenue, Garden Grove, CA. 92841, 714-898-8121, Fax: 714-893-2570
Page 5
Copyright © 2002
Rev. 1.0, 2006-03-10
WWW.Microsemi .COM
PanelMatch™ LXMG1617-05-2x
5V 2.2W CCFL Programmable Inverter Module
TM ®
TYPICAL APPLICATION
LXMG1617-05-2x
5V
SET2GND
VHI
VLO
BRITE VIN1
SLEEP
SET1
0.45V
to
2.0V
1.8K
20K
DAC or
Pot
CCFL
TUBE
NC NC
Figure 1 – Brightness Control
(output current set to maximum)
P.W.
10µs to 125µS
BRITE
LXMG1617-05-2x
0 < P.W. < 100% of period
PWM Signal
from System
Figure 1A – PWM Brightness Control
LXMG1617-05-2x
SET2GND
VHI
VLO
SLEEP
SET1
CCFL
TUBE
BRITE
5V
VIN1
L L 3.5mARMS
L H 4.0mARMS
H L 4.5mARMS
H H 5.0mARMS
L=GND; H=Open
Figure 2 – Max Output Current
(SET1 and SET2 Inputs)
The brightness control may be a voltage output DAC or
other voltage source, a digital pot or 20K manual pot. The
inverter contains an internal 10K pull-up to 3V to bias the
pot add a 1.8K resistor to set the lower threshold voltage.
A 3.3V Logic Level PWM signal from a micro-controller
may also be used as shown in Figure 1A.
If you need to turn the inverter ON/OFF remotely, connect
to TTL logic signal to the SLEEP input.
Connect VHI to high voltage wire from the lamp. Connect
VLO to the low voltage wire (wire with thinner insulation).
Never connect VLO to circuit ground as this will defeat
lamp current regulation. If both lamp wires have heavy
high voltage insulation, connect the longest wire to VLO.
This wire is typically white.
Use the SET1 and SET2 (see Figure 2) inputs to select the
desired maximum output current. Using these two pins in
combination allows the inverter to match a wide variety of
panels from different manufactures. Generally the best
lamp lifetime correlates with driving the CCFL at the
manufactures nominal current setting. However the SET1
and SET2 inputs allow the user the flexibility to adjust the
current to the maximum allowable output current to
increase panel brightness at the expense of some reduced
lamp life.
Although the SET pins are designed such that just leaving
them open or grounding them is all that is needed to set the
output current, they can also be actively set. Using a open
collector or open drain logic signal will allow you to
reduce the lamp current for situations where greater dim
range is required, as an example in nighttime situations. In
conjunction with a light sensor or other timer the panel
could be set to higher brightness (maximum output
current) for daytime illumination and lower brightness
(minimum or typical output current) at nighttime. Since
the dim ratio is a factor of both the burst duty cycle and the
peak output current, using this technique the effective dim
ratio can be increased greater than the burst duty cycle
alone. Conversely the SET inputs could be used to
overdrive the lamp temporarily to facilitate faster lamp
warm up at initial lamp turn on. Of course any possible
degradation on lamp life from such practices is the users
responsibility since not all lamps are designed to be
overdriven.
The inverter has a built in fault timeout function. If the
output is open (lamp disconnected or broken) or shorted
the inverter will attempt to strike the lamp for several
seconds. After about 2 seconds without success the inverter
will shutdown. In order to restart the inverter it is
necessary to toggle the sleep input or cycle the VIN1 input
supply.
A
AP
PP
PL
LI
IC
CA
AT
TI
IO
ON
N
P
RODUCTION
D
ATASHEET
Microsemi
Integrated Products
11861 Western Avenue, Garden Grove, CA. 92841, 714-898-8121, Fax: 714-893-2570
Page 6
Copyright © 2002
Rev. 1.0, 2006-03-10
WWW.Microsemi .COM
PanelMatch™ LXMG1617-05-2x
5V 2.2W CCFL Programmable Inverter Module
TM ®
NOTES
PRODUCTION DATA – Information contained in this document is proprietary to
Microsemi and is current as of publication date. This document may not be modified in
any way without the express written consent of Microsemi. Product processing does not
necessarily include testing of all parameters. Microsemi reserves the right to change the
configuration and performance of the product and to discontinue product at any time.
N
NO
OT
TE
ES
S
