TNPU e3 www.vishay.com Vishay Draloric Ultra Precision Thin Film Chip Resistors FEATURES * Low temperature tolerances coefficient and tight * Sulfur resistance verified according to ASTM B 809 * Superior moisture resistivity (85 C; 85 % RH) * Excellent overall stability at different environmental conditions 0.05 % (1000 h rated power at 70 C) * AEC-Q200 qualified * Material categorization: for definitions of compliance please see www.vishay.com/doc?99912 APPLICATIONS TNPU e3 ultra precision thin film flat chip resistors combine the proven reliability of TNPW e3 products with a most advanced level of precision and stability. This unique combination makes the product perfectly suited for all applications with outstanding requirements towards size, reliable precision and stability. * Industrial equipment * Telecommunication * Medical equipment * Instrumentation * Test and measuring equipment * Automotive TECHNICAL SPECIFICATIONS DESCRIPTION TNPU0603 e3 TNPU0805 e3 TNPU1206 e3 0603 0805 1206 Metric size code RR1608M RR2012M RR3216M Resistance range 100 to 100 k 100 to 332 k 100 to 511 k Imperial size Resistance tolerance 0.1 %; 0.05 %; 0.02 % Temperature coefficient Rated dissipation, P70 10 ppm/K; 5 ppm/K (1) Operating voltage, Umax. ACRMS/DC Permissible film temperature, F max. (1) Operating temperature range 0.1 W 0.125 W 0.25 W 75 V 150 V 200 V 125 C 125 C 125 C -55 C to 125 C -55 C to 125 C -55 C to 125 C 100 V 200 V 300 V 0.1 x 10-9/h 0.1 x 10-9/h 0.1 x 10-9/h Permissible voltage against ambient (insulation): 1 min; Uins FITobserved Note (1) Please refer to APPLICATION INFORMATION, see below. APPLICATION INFORMATION When the resistor dissipates power, a temperature rise above the ambient temperature occurs, dependent on the thermal resistance of the assembled resistor together with the printed circuit board. The rated dissipation applies only if the permitted film temperature is not exceeded. These resistors do not feature a limited lifetime when operated within the permissible limits. However, resistance value drift increasing over operating time may result in exceeding a limit acceptable to the specific application, thereby establishing a functional lifetime. Revision: 01-Jul-16 Document Number: 28779 1 For technical questions, contact: thinfilmchip@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 TNPU e3 www.vishay.com Vishay Draloric MAXIMUM RESISTANCE CHANGE AT RATED DISSIPATION OPERATION MODE STANDARD Rated dissipation, P70 TNPU0603 e3 0.100 W TNPU0805 e3 0.125 W TNPU1206 e3 0.250 W Operating temperature range -55 C to 125 C Permissible film temperature, F max. 125 C Max. resistance change at P70 for resistance range, |R/R| after: TNPU0603 e3 100 to 100 k TNPU0805 e3 100 to 332 k TNPU1206 e3 100 to 511 k 1000 h 0.05 % 8000 h 0.1 % 225 000 h 0.3 % TEMPERATURE COEFFICIENT AND RESISTANCE RANGE TYPE / SIZE TCR TOLERANCE 10 ppm/K 0.05 % 0.1 % TNPU0603 e3 5 ppm/K RESISTANCE E-SERIES 100 to 100 k 0.05 % 0.02 % 10 ppm/K 0.05 % 0.1 % 100 to 332 k TNPU0805 e3 E24; E192 5 ppm/K 0.05 % 0.02 % 10 ppm/K 100 to 200 k 0.05 % 0.1 % 100 to 511 k TNPU1206 e3 5 ppm/K 0.05 % 0.02 % Revision: 01-Jul-16 100 to 200 k Document Number: 28779 2 For technical questions, contact: thinfilmchip@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 TNPU e3 www.vishay.com Vishay Draloric PACKAGING TYPE / SIZE TNPU0603 e3 TNPU0805 e3 TNPU1206 e3 CODE QUANTITY PACKAGING STYLE WIDTH PITCH PACKAGING DIMENSIONS E52 = EN 1000 8 mm 4 mm O 180 mm / 7" ET1 = EA 5000 Tape and reel cardboard tape acc. IEC 60286-3, Type 1a PART NUMBER AND PRODUCT DESCRIPTION Part Number: TNPU12061K32AZEA00 T N P U 1 2 0 6 1 K 3 2 A Z E A 0 TYPE / SIZE RESISTANCE TOLERANCE TCR PACKAGING TNPU0603 TNPU0805 TNPU1206 R = Decimal K = Thousand M = Million (4 digits) B = 0.1 % A = 0.05 % H = 0.02 % Y = 10 ppm/K Z = 5 ppm/K EA EN 0 Product Description: TNPU1206 1K32 0.05 % T-16 ET1 e3 TNPU1206 1K32 0.05 % T-16 ET1 e3 TYPE / SIZE RESISTANCE TOLERANCE TCR PACKAGING LEAD (Pb)-FREE TNPU0603 TNPU0805 TNPU1206 Examples: 1K32 = 1320 0.1 % 0.02 % 0.05 % T-13 = 10 ppm/K T-16 = 5 ppm/K ET1 E52 e3 = Pure tin termination finish Note * Products can be ordered using either the PART NUMBER or the PRODUCT DESCRIPTION. Revision: 01-Jul-16 Document Number: 28779 3 For technical questions, contact: thinfilmchip@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 TNPU e3 www.vishay.com Vishay Draloric DESCRIPTION MATERIALS Production is strictly controlled and follows an extensive set of instructions established for reproducibility. A homogeneous film of metal alloy is deposited on a high grade AI2O3 ceramic substrate and conditioned to achieve the desired temperature coefficient. Specially designed inner contacts are deposited on both sides. A special laser is used to achieve the target value by smoothly fine trimming the resistive layer without damaging the ceramics. A further conditioning is applied in order to stabilize the trimming result. The resistor elements are covered by a protective coating designed for electrical, mechanical and climatic protection. The terminations receive a final pure tin on nickel plating. The result of the determined production is verified by an extensive testing procedure on 100 % of the individual chip resistors. Only accepted products are laid directly into the tape in accordance with IEC 60286-3 Type 1a (1). Vishay acknowledges the following systems for the regulation of hazardous substances: * IEC 62474, Material Declaration for Products of and for the Electrotechnical Industry, with the list of declarable substances given therein (2) * The Global Automotive Declarable Substance List (GADSL) (3) * The REACH regulation (1907/2006/EC) and the related list of substances with very high concern (SVHC) (4) for its supply chain The products do not contain any of the banned substances as per IEC 62474, GADSL, or the SVHC list, see www.vishay.com/how/leadfree. ASSEMBLY The resistors are suitable for processing on automatic SMD assembly systems. They are suitable for automatic soldering using wave, reflow or vapour phase as shown in IEC 61760-1 (1). The encapsulation is resistant to all cleaning solvents commonly used in the electronics industry, including alcohols, esters and aqueous solutions. The suitability of conformal coatings, potting compounds and their processes, if applied, shall be qualified by appropriate means to ensure the long-term stability of the whole system. The resistors are RoHS compliant, the pure tin plating provides compatibility with lead (Pb)-free and lead-containing soldering processes. The immunity of the plating against tin whisker growth has been proven under extensive testing. Hence the products fully comply with the following directives: * 2000/53/EC End-of-Life Vehicle Directive (ELV) and Annex II (ELV II) * 2011/65/EU Restriction of the Use of Hazardous Substances Directive (RoHS) with amendment 2015/863/EU * 2012/19/EU Waste Electrical and Electronic Equipment Directive (WEEE) Vishay pursues the elimination of conflict minerals from its supply chain, see the Conflict Minerals Policy at www.vishay.com/doc?49037. RELATED PRODUCTS For products with precision specification see the datasheet: * TNPW e3 - High Stability Thin Film Flat Chip Resistors (www.vishay.com/doc?28758) Notes (1) The quoted IEC standards are also released as EN standards with the same number and identical contents. (2) The IEC 62474 list of declarable substances is maintained in a dedicated database, which is available at http://std.iec.ch/iec62474. (3) The Global Automotive Declarable Substance List (GADSL) is maintained by the American Chemistry Council and available at www.gadsl.org. (4) The SVHC list is maintained by the European Chemical Agency (ECHA) and available at http://echa.europa.eu/candidate-list-table. Revision: 01-Jul-16 Document Number: 28779 4 For technical questions, contact: thinfilmchip@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 TNPU e3 www.vishay.com Vishay Draloric Rated Power in % FUNCTIONAL PERFORMANCE 120 100 80 60 40 20 0 -55 -25 0 25 50 75 70 100 Non-Linearity A3 in dB 100 150 175 Ambient Temperature in C Derating 110 125 TNPU1206 e3 TNPU0805 e3 TNPU0603 e3 90 80 70 60 40 100 1K 10K 100K Current Noise in V/V Non-Linearity 1M Resistance Value in 1 TNPU0805 e3 TNPU0603 e3 0.1 TNPU1206 e3 0.01 100 Current Noise Revision: 01-Jul-16 1K 10K 100K 1M Resistance Value in Document Number: 28779 5 For technical questions, contact: thinfilmchip@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 TNPU e3 www.vishay.com Vishay Draloric TEST AND REQUIREMENTS All tests are carried out in accordance with the following specifications: EN 60115-1, generic specification The tests are carried out under standard atmospheric conditions in accordance with IEC 60068-1, 4.3, whereupon the following values are applied: EN 60115-8 (successor of EN 140400), sectional specification Temperature: 15 C to 35 C EN 140401-801, detail specification Air pressure: 86 kPa to 106 kPa (860 mbar to 1060 mbar). IEC 60068-2-xx, test methods A climatic category LCT / UCT / 56 is applied, defined by the lower category temperature (LCT), the upper category temperature (UCT), and the duration of exposure in the damp heat, steady state test (56 days). Relative humidity: 25 % to 75 % The parameters stated in the Test Procedures and Requirements table are based on the required tests and permitted limits of EN 140401-801. The table presents only the most important tests, for the full test schedule refer to the documents listed above. However, some additional tests and a number of improvements against those minimum requirements have been included. The components are mounted for testing on printed circuit boards in accordance with EN 60115-8, 2.4.2, unless otherwise specified. The testing also covers most of the requirements specified by EIA / ECA-703 and JIS-C-5201-1. TEST PROCEDURES AND REQUIREMENTS EN 60115-1 CLAUSE IEC 60068-2 (1) TEST METHOD TEST PROCEDURE REQUIREMENTS PERMISSIBLE CHANGE (R) Stability for product types: TNPU0603 e3 TNPU0805 e3 TNPU1206 e3 4.5 4.8 - Resistance - Temperature coefficient 0.1 %; 0.05 %; 0.02 % At (20 / -55 / 20) C and (20 / 125 / 20) C 10 ppm/K; 5 ppm/K U = P 70 x R or U = Umax.; whichever is the less severe; 4.25.1 4.25.3 4.24 - 4.23.3 70 C; 1000 h (0.05 % R + 0.01 ) 70 C; 8000 h (0.1 % R + 0.02 ) - Endurance at upper category temperature 125 C; 1000 h (0.05 % R + 0.01 ) 125 C; 8000 h (0.1 % R + 0.02 ) 78 (Cab) Damp heat, steady state (40 2) C; 56 days; (93 3) % RH (0.1 % R + 0.01 ) 4.23 4.23.2 1.5 h on; 0.5 h off; Endurance at 70 C Climatic sequence: 2 (Bb) 30 (Db) Dry heat UCT; 16 h Damp heat, cyclic 55 C; 24 h; > 90 % RH; 5 cycle 4.23.4 1 (Ab) Cold LCT; 2 h 4.23.5 13 (M) Low air pressure 8.5 kPa; 2 h; (25 10) C 4.23.6 30 (Db) Damp heat, cyclic 55 C; 24 h; > 90 % RH; 5 cycles 4.23.7 - D.c. load 1 (Aa) Cold U= - Revision: 01-Jul-16 (0.1 % R + 0.02 ) P 70 x R Umax.; 1 min LCT = -55 C UCT = 125 C -55 C; 2 h (0.05 % R + 0.01 ) Document Number: 28779 6 For technical questions, contact: thinfilmchip@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 TNPU e3 www.vishay.com Vishay Draloric TEST PROCEDURES AND REQUIREMENTS EN 60115-1 CLAUSE IEC 60068-2 (1) TEST METHOD TEST PROCEDURE REQUIREMENTS PERMISSIBLE CHANGE (R) Stability for product types: TNPU0603 e3 TNPU0805 e3 TNPU1206 e3 4.19 14 (Na) Rapid change of temperature 30 min at LCT and 30 min at UCT; LCT = -55 C; UCT = 125 C; 1000 cycles 4.13 - Short time overload U = 2.5 x P 70 x R or U = 2 x Umax.; whichever is the less severe; 5s (0.05 % R + 0.01 ) Vibration Endurance by sweeping; 10 Hz to 2000 Hz; no resonance; amplitude 1.5 mm or 200 m/s2; 6 h (0.05 % R + 0.01 ) no visible damage 4.22 6 (Fc) Solder bath method; SnPb40; non-activated flux (215 3) C; (3 0.3) s (0.1 % R + 0.01 ) Good tinning ( 95 % covered); no visible damage 4.17 58 (Td) Solderability Solder bath method; SnAg3Cu0,5 or SnAg3,5; non-activated flux (235 3) C; (2 0.2) s 4.18 58 (Td) Resistance to soldering heat Solder bath method; (260 5) C; (10 1) s (0.02 % R + 0.01) 4.29 45 (XA) Component solvent resistance Isopropyl alcohol +50 C; method 2 No visible damage 4.32 21 (Ue3) Shear (adhesion) RR 2012M and RR 3216M; 45 N 4.33 21 (Ue1) Substrate bending Depth 2 mm, 3 times (0.05 % R + 0.01) no visible damage, no open circuit in bent position 4.7 - Voltage proof URMS = Uins; 60 5 s No flashover or breakdown - Flammability IEC 60 695-11-5 (1), needle flame test; 10 s No burning after 30 s 4.39 - Periodic electric overload: Standard operation mode U = 15 x P 70 x R or U = 2 x Umax.; whichever is the less severe; 0.1 s on; 2.5 s off; 1000 cycles (0.1 R + 0.02 ) 4.37 67 (Cy) Damp heat, steady state, accelerated (85 5) C; 56 days (85 5) % RH (0.25 R + 0.05 ) Electro static discharge (Human Body Model) IEC 61340-3-1 (1); 3 pos. + 3 neg. (equivalent to MIL-STD-883, method 3015) TNPU0603: 1000 V TNPU0805: 1500 V TNPU1206: 2000 V (0.5 R + 0.05 ) RR 1608M; 9 N 4.35 4.38 - No visible damage Note (1) The quoted IEC standards are also released as EN standards with the same number and identical contents. Revision: 01-Jul-16 Document Number: 28779 7 For technical questions, contact: thinfilmchip@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 TNPU e3 www.vishay.com Vishay Draloric DIMENSIONS L Tt W H Tb DIMENSIONS AND MASS H (mm) L (mm) W (mm) Tt (mm) Tb (mm) MASS (mg) TNPU0603 e3 0.45 0.10 1.6 0.10 0.85 0.10 0.3 0.20 0.3 0.20 2 TNPU0805 e3 0.45 0.10 2.0 0.15 1.25 0.15 0.4 0.20 0.4 0.20 5.5 TNPU1206 e3 0.55 0.10 3.2 0.15 1.6 0.15 0.5 0.25 0.5 0.25 10 TYPE / SIZE SOLDER PAD DIMENSIONS G X Y RECOMMENDED SOLDER PAD DIMENSIONS REFLOW SOLDERING TYPE / SIZE WAVE SOLDERING Y (mm) X (mm) G (mm) Y (mm) X (mm) G (mm) TNPU0603 e3 0.5 0.9 1.0 0.9 0.9 1.0 TNPU0805 e3 0.7 1.3 1.2 0.9 1.3 1.3 TNPU1206 e3 0.9 1.7 2.0 1.1 1.7 2.3 Revision: 01-Jul-16 Document Number: 28779 8 For technical questions, contact: thinfilmchip@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Legal Disclaimer Notice www.vishay.com Vishay Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, "Vishay"), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay's knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer's responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and / or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer's technical experts. Product specifications do not expand or otherwise modify Vishay's terms and conditions of purchase, including but not limited to the warranty expressed therein. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. (c) 2017 VISHAY INTERTECHNOLOGY, INC. ALL RIGHTS RESERVED Revision: 08-Feb-17 1 Document Number: 91000