White Electronic Designs PCMCIA Flash Memory Card FLA Series PCMCIA Flash Memory Card 1 MEGABYTE through 40 MEGABYTE (Intel/Sharp based) ARCHITECTURE OVERVIEW FEATURES WEDC's FLA series is designed to support from 2 to 20, 4Mb, 8Mb or 16Mb components, providing a wide range of density options. Cards are based on the 28F008SA (8Mb) for 12V VPP applications or on the 28F004S5 (4Mb), 28F008S5 (8Mb) and 28F016S5 (16Mb) devices for 5V only applications. Devices codes for the 28F004S5, 28F008SA, 28F008S5 and the 28F016S5 are: A7H, A2H, A6H and AAh respectively. Systems should be able to recognize all four codes. Cards utilizing the 8Mb components provide densities ranging from 2MB to 20MB in 2MB increments, cards utilizing 16Mb components provide densities ranging from 4MB to 40MB in 4MB increments. 4 Mbit memory devices are used only for smallest capacity cards (1MB). Low cost High Density Linear Flash Card Supports 5V only systems or 5V systems with 12V VPP Based on Intel/Sharp FlashFile Components Fast Read Performance - 150ns or 200ns Maximum Access Time x8 / x16 Data Interface High Performance Random Writes - 8s Typical Word Write Time Automated Write and Erase Algorithms - Command User Interface In support of the PC Card 95 standard for word wide access devices are paired. Therefore, the Flash array is structured in 64K word (128kBytes) blocks. Write, read and block erase operations can be performed as either a word or byte wide operation . By multiplexing A0, CE1# and CE2,# 8-bit hosts can access all data on data lines DQ0-DQ7. 100,000 Erase Cycles per Block 64K word symmetrical Block Architecture PC Card Standard Type I Form Factor GENERAL DESCRIPTION WEDC's FLA Series Flash memory cards offer high density linear Flash solid state storage solutions for code and data storage, high performance disk emulation and execute in place (XIP) applications in mobile PC and dedicated (embedded) equipment. The FLA21-FLA36 series also supports the following PCMCIA compatible register functions: Soft Reset via the Configuration Option Register, Power Down (sleep mode) via the Configuration and Status Register and monitoring of Ready/Busy, Soft Reset and Power Down via the Card Status Register (cards without attribute memory and versions FLA51 - FLA66 do not have registers). FLA series cards conform to PCMCIA international standard. The card's control logic provides the system interface and controls the internal Flash memories. Card can be read/written in byte-wide or word-wide mode which allows for flexible integration into various systems. Combined with file management software, such as Flash Translation Layer (FTL), FLA Flash cards provide removable highperformance disk emulation. The FLA series cards conform with the PC Card Standard (PCMCIA) and JEIDA, providing electrical and physical compatibility. The PC Card form factor offers an industry standard pinout and mechanical outline, allowing density upgrades without system design changes. WEDC's standard cards are shipped with WEDC's Logo. Cards are also available with blank housings (no Logo). The blank housings are available in both a recessed (for label) and flat housing. Please contact WEDC sales representative for further information on Custom artwork. The FLA series offers low power modes controlled by registers. Standard cards contain separate 2kB EEPROM memory for Card Information Structure (CIS) which can be used for easy identification of card characteristics. The WEDC FLA series is based on Intel/Sharp Flash memories. Note: Standard options include attribute memory. Cards without attribute memory are available. Cards are also available with or without a hardware write protect switch. White Electronic Designs Corp. reserves the right to change products or specifications without notice. July 2007 Rev. 6 1 White Electronic Designs Corporation * (602) 437-1520 * www.whiteedc.com White Electronic Designs PCMCIA Flash Memory Card FLA Series BLOCK DIAGRAM Device Pair (N/2 - 1) CSn Device (N-1) Device (N-2) Array Address Bus ADDRESS BUFFER ADDRESS BUS A1-A25 Control Address Bus M Res WL# RL# WH# RH# Device Pair 1 Device 2 Device 3 Device Pair 0 Device 1 CS1 Control Logic PCMCIA Interface CE2# CE1# CSn Cn CS0 C0 Ctrl At/Reg enable WH# RH# Device 0 DATA BUS Q8-Q15 DATA BUS Q0-Q7 REG# A0 WP SR Clr Reg C;r /SR /PD CS0 4000h VCC WE# OE# WL# RL# 0000h Card Management Registers attrib. mem CIS EEPROM 2kB VCC control Q0-Q7 VCC I/O buffer DATA BUS D0-D7 DATA BUS D8-D15 Device type 28F004S5 28F008SA 28F008S5 Manuf ID 89H 89H 89H Device ID A7H A2H A6H 28F016S5 89H AAH White Electronic Designs Corp. reserves the right to change products or specifications without notice. July 2007 Rev. 6 2 White Electronic Designs Corporation * (602) 437-1520 * www.whiteedc.com White Electronic Designs REGISTERS IN ATTRIBUTE MEMORY SPACE* ADDRESS 4100h 4002h CSR CONFIGURATION STATUS REGISTER: ADRS = 4002H WRITE ONLY REGISTER NAME Status Register Config. and Status Register Not Supported 4000h Configuration Option Register *Cards without Att. Mem and FLA51- FLA66 do not have registers D7 D2 D7 D7 LREQ D6 D6 D4 D3 D2 D1 PDwn D4 D3 Not Supported D2 D1 D0 Power Down, active High 0 = Normal Operation default = 0 Power On SR STATUS REGISTER: ADRS = 4100H READ ONLY Configuration Index D5 D5 1 = Place all memory devices in power down mode COR CONFIGURATION OPTION REGISTER: ADRS = 4000H WRITE ONLY SRES PCMCIA Flash Memory Card FLA Series D0 Soft Reset, active High Not Supported 1 = Reset State D7 D6 D5 0 = End Reset State SReset D5 PDwn D4 D3 Not Supported D2 D1 R/BSY D0 Represents the state of SRESET bit in COR (4000h) D6 Level Req (not supported) 1 = Reset D5-D0 Configuration index (not supported) 0 = Normal Operation Power On default D3 (4002h) D5 = 0 Represents the state of Power Down bit (D2) in CSR 1 = Power Down D0 Reflects the card's Ready/Busy signal (pin 16) driven by memory components Ready/ Busy outputs. This bit allows software polling of the card's Ready/Busy status. 1 = Ready MECHANICAL Interconnect area 1.0mm + 0.05 (0.039") 1.6mm + 0.05 (0.063") 3.0mm MIN 10.0mm MIN (0.400") Substrate area 54.0mm + 0.10 (2.126") 85.6mm + 0.20 (3.370") 1.0mm + 0.05 (0.039") 10.0mm MIN (0.400") 3.3mm + T1 (0.130") T1=0.10mm unterconnect area T1=0.20mm substrate area White Electronic Designs Corp. reserves the right to change products or specifications without notice. July 2007 Rev. 6 3 White Electronic Designs Corporation * (602) 437-1520 * www.whiteedc.com White Electronic Designs PCMCIA Flash Memory Card FLA Series PINOUT Pin 1 Signal name GND I/O Function Ground 2 DQ3 I/O 3 DQ4 I/O Active Signal name GND Data bit 3 Pin 35 36 I/O Function Ground Active Data bit 4 37 CD1# O Card Detect 1 LOW DQ11# I/O Data bit 11 4 DQ5 I/O Data bit 5 38 DQ12 I/O Data bit 12 5 DQ6 I/O Data bit 6 39 DQ13 I/O Data bit 13 6 DQ7 I/O Data bit 7 40 DQ14 I/O Data bit 14 7 CE1# I Card enable 1 41 DQ15 I Data bit 15 8 A10 I Address bit 10 42 CE2 I Card Enable 2 LOW 9 OE# I Output enable 43 VS1# O Voltage Sense 1 NC 10 A11 I Address bit 11 44 RFU LOW LOW Reserved 11 A9 I Address bit 9 45 RFU 12 A8 I Address bit 8 46 A17 I 13 A13 I Address bit 13 47 A18 I Address bit 18 14 A14 I Address bit 14 48 A19 I Address bit 19 I Write Enable LOW 49 A20 I Address bit 20 2MB(3) O Ready/Busy LOW (4) 50 A21 I Address bit 21 4MB(3) 51 VCC 15 16 WE# RDY/BSY# Supply Voltage Reserved Address bit 17 17 VCC 18 VPP1 52 VPP2 Prog. Voltage NC 19 A16 I Address bit 16 53 A22 I Address bit 22 8MB(3) 20 A15 I Address bit 15 54 A23 I Address bit 23 16MB(3) 21 A12 I Address bit 12 55 A24 I Address bit 24 32MB(3) 22 A7 I Address bit 7 56 A25 I Address bit 25 64MB(3) 23 A6 I Address bit 6 57 VS2 O Voltage Sense 2 NC 24 A5 I Address bit 5 58 RST I Card Reset HIGH (4) 25 A4 I Address bit 4 59 Wait O Extended Bus cycle Low(2,4) 26 A3 I Address bit 3 60 RFU# 27 A2 I Address bit 2 61 REG I Attrib Mem Select 28 A1 I Address bit 1 62 BVD2# O Bat. Volt. Detect 2 (2) 29 A0 I Address bit 0 63 BVD1 O Bat. Volt. Detect 1 (2) Data bit 8 Prog. Voltage NC Supply Voltage Reserved 30 DQ0 I/O Data bit 0 64 DQ8 I/O 31 DQ1 I/O Data bit 1 65 DQ9 I/O Data bit 9 32 DQ2 I/O Data bit 2 66 DQ10 O Data bit 10 33 WP O Write Potect 67 CD2 O Card Detect 2 34 GND 68 GND# HIGH Ground LOW Ground Notes: 1. RDY/BSY signal is an "Open drain" type output, pull-up resistor on host side is required. 2. Wait#, BVD1 and BVD2 are driven high for compatibility. 3. Shows density for which specified address bit is MSB. Higher order address bits are no connects (ie 4MB A21 is MSB A22 - A25 are NC). 4. NC - No Connection for FLA51 - FLA66. White Electronic Designs Corp. reserves the right to change products or specifications without notice. July 2007 Rev. 6 4 White Electronic Designs Corporation * (602) 437-1520 * www.whiteedc.com White Electronic Designs PCMCIA Flash Memory Card FLA Series CARD SIGNAL DESCRIPTION Symbol A0 - A25 Type INPUT DQ0 - DQ15 CE1#, CE2# INPUT/OUTPUT INPUT OE# WE# RDY/ BSY#(*) INPUT INPUT OUTPUT CD1#, CD2# OUTPUT WP OUTPUT VPP1, VPP2 VCC GND REG# N.C. INPUT RST(*) INPUT WAIT#(*) BVD1, BVD2 VS1, VS2 RFU NC OUTPUT OUTPUT OUTPUT Name and Function ADDRESS INPUTS: A0 through A25 enable direct addressing of up to 64MB of memory on the card. Signal A0 is not used in word access mode. A25 is the most significant bit DATA INPUT/OUTPUT: DQ0 THROUGH DQ15 constitute the bi-directional databus. DQ15 is the MSB. CARD ENABLE 1 AND 2: CE1# enables even byte accesses, CE2# enables odd byte accesses. Multiplexing A0, CE1# and CE2# allows 8-bit hosts to access all data on DQ0 - DQ7. OUTPUT ENABLE: Active low signal gating read data from the memory card. WRITE ENABLE: Active low signal gating write data to the memory card. READY/BUSY OUTPUT: Indicates status of internally timed erase or program algorithms. A high output indicates that the card is ready to accept accesses. A low output indicates that one or more devices in the memory card are busy with internally timed erase or write activities. CARD DETECT 1 and 2: Provide card insertion detection. These signals are internally connected to ground on the card. The host shall monitor these signals to detect card insertion (pulled-up on host side). WRITE PROTECT: Write protect reflects the status of the Write Protect switch on the memory card. WP set to high = write protected, providing internal hardware write lockout to the Flash array.If card does not include optional write protect switch, this signal will be pulled low internally indicating write protect = "off". PROGRAM/ERASE POWER SUPPLY: Provides programming voltages for card (12V). Not connected for 5V only card. CARD POWER SUPPLY: (5.0V). CARD GROUND ATTRIBUTE MEMORY SELECT : Active low signal, enables access to Attribute Memory Plane, occupied by Card Information Structure and Card Registers. RESET: Active high signal for placing card in Power-on default state. Reset can be used as a Power-Down signal for the memory array. WAIT: This signal is pulled high internally for compatibility. No wait states are generated. BATTERY VOLTAGE DETECT: These signals are pulled high to maintain SRAM card compatibility. VOLTAGE SENSE: Notifies the host socket of the card's VCC requirements. VS1 and VS2 are open to indicate a 5V card . RESERVED FOR FUTURE USE NO INTERNAL CONNECTION TO CARD: pin may be driven or left floating (*) Signals not supported by FLA51-66 (N.C) FUNCTIONAL TRUTH TABLE READ function Function Mode Standby Mode Byte Access (8 bits) Word Access (16 bits) Odd-Byte Only Access WRITE function Standby Mode Byte Access (8 bits) Word Access (16 bits) Odd-Byte Only Access Common Memory Attribute Memory CE2# CE1# A0 OE# WE# REG# D15-D8 D7-D0 REG# D15-D8 D7-D0 H H H L L H L L L H X L H X X X L L L L X H H H H X H H H H High-Z High-Z High-Z Odd-Byte Odd-Byte High-Z Even-Byte Odd-Byte Even-Byte High-Z X L L L L High-Z High-Z High-Z Not Valid Not Valid High-Z Even-Byte Not Valid Even-Byte High-Z H H H L L H L L L H X L H X X X H H H H X L L L L X H H H H X X X Odd-Byte Odd-Byte X Even-Byte Odd-Byte Even-Byte X X L L L L X X X X X X Even-Byte X Even-Byte X White Electronic Designs Corp. reserves the right to change products or specifications without notice. July 2007 Rev. 6 5 White Electronic Designs Corporation * (602) 437-1520 * www.whiteedc.com White Electronic Designs PCMCIA Flash Memory Card FLA Series ABSOLUTE MAXIMUM RATINGS (1) Operating Temperature TA (ambient) Commercial Industrial Storage Temperature Commercial Industrial Voltage on any pin relative to VSS 0C to +60 C -40C to +85 C 0C to +60 C -40C to +85 C -0.5V to VCC+0.5V VCC supply Voltage relative to VSS -0.5V to +7.0V Note: (1) Stress greater than those listed under "Absolute Maximum ratings" may cause permanent damage to the device. This is a stress rating only and functional operation at these or any other conditions greater than those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability. DC CHARACTERISTICS (1) Symbol ICCR Parameter VCC Read Current Density(Mbytes) All Notes ICCW VCC Program Current All ICCW IPPW ICCE ICCS (CMOS) VCC Program Current VPP Program Current VCC Erase Current VCC Standby Current All All All 2MB 20MB 2MB 20MB 4MB 40MB 28F008S5 28F016S5 28F008SA Vpp=12V 2 28F008SA 2 28F008S5 2 28F016S5 Typ(3) 110 900 600 420 60 380 Max 35 Units mA 75 mA 30 30 100 230 mA mA mA A Test Conditions VCC = VCCmax tcycle = 150ns,CMOS levels VCC = VCCmax Control Signals = VCC Reset = VSS, CMOS levels CMOS Test Conditions: VCC = 5V 5%, VIL = VSS 0.2V, VIH = VCC 0.2V Notes: 1. All currents are RMS values unless otherwise specified. ICCR, ICCW and ICCE are based on Byte wide operations. For 16 bit operation values are double. 2. Control Signals: CE1#, CE2#, OE#, WE#, REG#. 3. Typical: VCC = 5V, T = +25C. Symbol ILI Parameter Input Leakage Current Notes 1 ILO Output Leakage Current 1 VIL VIH VOL VOH VLKO Input Low Voltage Input High Voltage Output Low Voltage Output High Voltage VCC Erase/Program Lock Voltage 1 1 1 1 1 Min 0 0.7VCC VCC-0.4 2.0 Max 20 Units A 20 A 0.8 VCC+0.5 0.4 VCC V V V V V Test Conditions VCC = VCCMAX VIN =VCC or VSS VCC = VCCMAX VOUT =VCC or VSS IOL = 3.2mA IOH = -2.0mA Notes: 1. Values are the same for byte and word wide modes for all card densities. 2. Exceptions: Leakage currents on CE1, CE2, OE, REG and WE will be < 500 A when VIN = GND due to internal pull-up resistors. Leakage currents on RST will be <150A when VIN=VCC due to internal pull-down resistor. White Electronic Designs Corp. reserves the right to change products or specifications without notice. July 2007 Rev. 6 6 White Electronic Designs Corporation * (602) 437-1520 * www.whiteedc.com White Electronic Designs PCMCIA Flash Memory Card FLA Series AC CHARACTERISTICS - READ TIMING PARAMETERS SYMBOL (PCMCIA) tC(R) tA(A) tA(CE) tA(OE) tSU(A) tSU(CE) tH(A) tH(CE) tV(A) tDIS(CE) tDIS(OE) tEN(CE) tEN(OE) tREC(RSR) Parameter 150ns Read Cycle Time Address Access Time Card Enable Access Time Output Enable Access Time Address Setup Time Card Enable Setup Time Address Hold Time Card Enable Hold Time Output Hold from Address Change Output Disable Time from CE# Output Disable Time from OE# Output Enable Time from CE# Output Enable Time from OE# Power Down recovery to Output Delay. VCC = 5V Min 150 Max 150 150 75 20 0 20 20 0 75 75 5 5 500 Unit ns ns ns ns ns ns ns ns ns ns ns ns ns ns Note: AC timing diagrams and characteristics are guaranteed to meet or exceed PCMCIA 2.1 specifications. READ TIMING DIAGRAM tC(R) tH(A) tA(A) A[25::0], REG# tV(A) tA(CE) tSU(CE) CE1#, CE2# NOTE 1 NOTE 1 tH(CE) tSU(A) tA(OE) tDIS(CE) OE# tEN(OE) tDIS(OE) D[15::0] DATA VALID Note: Signal may be high or low in this area. White Electronic Designs Corp. reserves the right to change products or specifications without notice. July 2007 Rev. 6 7 White Electronic Designs Corporation * (602) 437-1520 * www.whiteedc.com White Electronic Designs PCMCIA Flash Memory Card FLA Series AC CHARACTERISTICS - WRITE TIMING PARAMETERS 150ns SYMBOL (PCMCIA) Parameter tCW tW(WE) tSU(A) tSU(A-WEH) tSU(CE-WEH) tSU(D-WEH) tH(D) tREC(WE) tDIS(WE) tDIS(OE) tEN(WE) tEN(OE) tSU(OE-WE) tH(OE-WE) tSU(CE) Write Cycle Time Write Pulse Width Address Setup Time Address Setup Time for WE# Card Enable Setup Time for WE# Data Setup Time for WE# Data Hold Time Write Recover Time Output Disable Time from WE# Output Disable Time from OE# Output Enable Time from WE# Output Enable Time from OE# Output Enable Setup from WE# Output Enable Hold from WE# Card Enable Setup Time from OE# Min 150 80 20 100 100 50 20 20 Max 75 75 5 5 10 10 0 Unit ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns Note: AC timing diagrams and characteristics are guaranteed to meet or exceed PCMCIA 2.1 specifications. WRITE TIMING DIAGRAM tC(W) A[25::0], REG# tSU(A-WEH) CE1#, CE2# tREC(WE) tH(CE) tSU(CE-WEH) tSU(CE) NOTE 1 NOTE 1 OE# tH(OE-WE) tSU(A) tW(WE) WE# tH(D) tSU(OE-WE) D[15::0](DIN) tSU(D-WEH) NOTE 2 DATA INPUT tDIS(WE) tEN(OE) tDIS(OE) tEN(WE) D[15::0](DOUT) NOTE 2 Note: 1. Signal may be high or low in this area. 2. When the data I/O pins are in the output state, no signals shall be applied to the data pins (D15-D0) by the host system. White Electronic Designs Corp. reserves the right to change products or specifications without notice. July 2007 Rev. 6 8 White Electronic Designs Corporation * (602) 437-1520 * www.whiteedc.com White Electronic Designs PCMCIA Flash Memory Card FLA Series DATA WRITE AND ERASE PERFORMANCE (1,3) VCC = 5V 5%, TA = 0C TO + 70C Symbol Parameter Notes tWHQV1 Word/Byte Program time 4 Block Program Time device SA Min Typ(1) Max 8 Units s tEHQV1 tWHQV2 0.6 device S5 tEHQV2 Block Erase Time 0.4 device SA 2.1 sec 10 sec 0.5 1.6 Notes: 1. Typical: Nominal voltages and TA = 25C. 2. Excludes system overhead. 3. Valid for all speed options. 4. To maximize system performance RDY/BSY# signal should be polled. PRODUCT MARKING EDI WED 7P016FLA6200C15 C995 9915 COMPANY NAME PART NUMBER LOT CODE/TRACE NUMBER DATE CODE Note: Some products are currently marked with our pre-merger company name/acronym (EDI). During our transition period, some products will also be marked with our new company name/acronym (WED). Starting October 2000 all PCMCIA products will be marked only with the WED prefix. White Electronic Designs Corp. reserves the right to change products or specifications without notice. July 2007 Rev. 6 9 White Electronic Designs Corporation * (602) 437-1520 * www.whiteedc.com White Electronic Designs PART NUMBERING PCMCIA Flash Memory Card FLA Series 7 P 016 FLA62 00 C 15 CARD TECHNOLOGY 7 FLASH 8 SRAM PC CARD P R CARD CAPACITY 016 Standard PCMCIA Ruggedized PCMCIA 16MB CARD FAMILY AND VERSION - See Card Family and Version Info. for details (next page) PACKAGING OPTION 00 Standard, type 1 TEMPERATURE RANGE C = I = Commercial 0C to +70C Industrial -40C to +85C CARD ACCESS TIME 15 150ns 25 250ns CARD FAMILY AND VERSION INFORMATION FLA30 With Attribute Memory, no Write Protect FLA31 No Attribute Memory, with Write Protect FLA32 With Attribute Memory, with Write Protect Example P/N FLA21-FLA24 Based on 28F008SA (requires 12V VPP for programming and erase functions) 7P004FLA3000C15 FLA21 No Attribute Memory, no Write Protect FLA22 With Attribute Memory, no Write Protect FLA23 No Attribute Memory, with Write Protect FLA33 No Attribute Memory, no Write Protect With Attribute Memory, with Write Protect FLA34 With Attribute Memory, no Write Protect FLA35 No Attribute Memory, with Write Protect FLA36 With Attribute Memory, with Write Protect FLA24 Example P/N FLA25-FLA28 applications FLA33-FLA36 applications 7P004FLA2200C15 Based on 28F004S5 for 5V only Example P/N Based on 28F008S5 for 5V only 7P004FLA3600C15 FLA25 No Attribute Memory, no Write Protect FLA26 With Attribute Memory, no Write Protect FLA27 No Attribute Memory, with Write Protect - no registers FLA28 With Attribute Memory, with Write Protect - signals RST, RDY/BSY, Wait are not connected Example P/N FLA51-FLA54 Based on 28F008SA; the same as FLA21-FLA24 with exception: 7P004FLA2600C15 FLA51 No Attribute Memory, no Write FLA52 With Attribute Memory, no Write FLA53 No Attribute Memory, with Write Protect FLA29-FLA32 applications FLA29 Based on 28F016S5 for 5V only Protect No Attribute Memory, no Write Protect White Electronic Designs Corp. reserves the right to change products or specifications without notice. July 2007 Rev. 6 10 White Electronic Designs Corporation * (602) 437-1520 * www.whiteedc.com White Electronic Designs PCMCIA Flash Memory Card FLA Series Protect FLA54 With Attribute Memory, with Write Protect Example P/N FLA60 With Attribute Memory, no Write FLA61 No Attribute Memory, with Write FLA62 With Attribute Memory, with Protect 7P004FLA5200C15 Protect FLA55-FLA58 Based on 28F008S5; the same as FLA25FLA28 with exception: Write Protect - no registers Example P/N 7P004FLA6000C15 - signals RST, RDY/BSY, Wait are not connected FLA55 No Attribute Memory, no Write Protect FLA56 With Attribute Memory, no Write Protect FLA57 No Attribute Memory, with Write Protect - no registers FLA58 With Attribute Memory, with Write Protect - signals RST, RDY/BSY, Wait are not connected Example P/N FLA63-FLA66 Based on 28F004S5; the same as FLA33FLA36 with exception: 7P004FLA5600C15 FLA59-FLA62 Based on 28F016S5; the same as FLA29FLA32 with exception: FLA63 No Attribute Memory, no Write FLA64 With Attribute Memory, no Write Protect - no registers Protect - signals RST, RDY/BSY, Wait are not connected FLA59 No Attribute Memory, no Write Protect FLA65 No Attribute Memory, with Write Protect FLA66 With Attribute Memory, with Write Protect Example P/N ORDERING INFORMATION 7P004FLA6600C15 7P XXX FLAYY SS T ZZ XXX 0021) 004 0061) 008 0101) 012 0141) 016 2MB 1) Available only for FLA21-FLA24, FLA25-FLA28, FLA51-FLA54, and FLA55-FLA59 2) Available only for FLA29-FLA32 and FLA59-FLA62 6MB 10MB 14MB 0181) 4MB 0242) 8MB 0322) 12MB 0402) 16MB 18MB 020 24MB 0282) 32MB 0362) 40MB 20MB 28MB 36MB FLAYY Card Family and Version (See Card Family and Version Information) SS 00 WEDC Logo Silkscreen 01 Blank Housing, Type I 02 Blank Housing, Type I Recessed T C I** = = Commercial Industrial -40C to +85C 0C to +70C ZZ 15 150ns Notes: Options without attribute memory and with hardware write protect switch are available. ** Denotes advanced information. White Electronic Designs Corp. reserves the right to change products or specifications without notice. July 2007 Rev. 6 11 White Electronic Designs Corporation * (602) 437-1520 * www.whiteedc.com White Electronic Designs PCMCIA Flash Memory Card FLA Series CIS INFORMATION FOR FLA SERIES CARDS ADDRESS VALUE DESCRIPTION ADDRESS VALUE 00H 01H CISTPL_DEVICE 44H 49H I 02H 03H TPL_LINK 46H 37H 7 04H 53H FLASH = 150ns (device writable) 48H 50H P 06H 06H 0EH 16H 1EH 26H 2EH 36H 3EH 46H 4EH 5EH 6EH 7EH 8EH 9EH CARD SIZE: 2MB 4MB 6MB 8MB 10MB 12MB 14MB 16MB 18MB 20MB 24MB 28MB 32MB 36MB 40MB 4AH 30H 0 08H FFH END OF DEVICE 0AH 18H CISTPL_JEDEC_C 4CH DESCRIPTION x 4EH x 50H 46H F 52H 4CH L 54H 41H A 56H 58H 32H 32H 2 based on 28F008SA 2 with Att. Mem. no WP 32H 36H 2 based on 28F008S5 6 with Att. Mem. no WP 33H 30H 3 based on 28F016S5 0 with Att. Mem. no WP - 5AH 2DH 5CH 2DH - 5EH 2DH - 60H 31H 1 62H 35H 5 64H 20H SPACE END TEXT 0CH 02H TPL_LINK 0EH 89H INTEL - ID 10H A2H A6H AAH 66H 00H 12H 17H CISTPL_DEVICE_A 68H 43H C 14H 03H TPL_LINK 6AH 4FH O 16H 42H EEPROM - 200ns 6CH 50H P 18H 01H Device Size = 2KBytes 6EH 59H Y R INTEL INTEL INTEL 28F008SA - ID 28F008S5 - ID 28F016S5 - ID 1AH FFH END OF TUPLE 70H 52H 1CH 1EH CISTPL_DEVICEGEO 72H 49H I 1EH 06H TPL_LINK 74H 47H G 20H 02H DGTPL_BUS 76H 48H H 22H 11H DGTPL_EBS 78H 54H T 24H 01H DGTPL_RBS 7AH 20H SPACE 26H 01H DGTPL_WBS 66H 00H END TEXT 28H 01H DGTPL_PART 68H 43H C 2AH 01H FLASH DEVICE NON-INTERLEAVED 6AH 4FH O 6CH 50H P 2CH 20H CISTPL_MANFID 6EH 59H Y TPL_LINK(04H) R 2EH 04H 70H 52H 30H F6H EDI TPLMID_MANF: LSB 72H 49H I 32H 01H EDI TPLMID_MANF: MSB 74H 47H G 34H 00H LSB: Number Not Assigned 76H 48H H 36H 00H MSB: Number Not Assigned 78H 54H T 38H 15H CISTPL_VERS1 7AH 20H SPACE E 3AH 47H TPL_LINK 7CH 45H 3CH 05H TPLLV1_MAJOR 7EH 4CH L 3EH 00H TPLLV1_MINOR 80H 45H E 40H 45H E 42H 44H D 82H 84H 43H 54H C T White Electronic Designs Corp. reserves the right to change products or specifications without notice. July 2007 Rev. 6 12 White Electronic Designs Corporation * (602) 437-1520 * www.whiteedc.com White Electronic Designs PCMCIA Flash Memory Card FLA Series CIS INFORMATION FOR FLA SERIES CARDS (CONT.) ADDRESS 86H 88H 8AH 8CH 8EH 90H 92H 94H 96H 98H 9AH 9CH 9EH A0H A2H A4H A6H A8H AAH ACH AEH B0H B2H B4H B6H B8H BAH BCH BEH C0H C2H C4H C6H C8H CAH CCH CEH D0H D2H D4H D6H D8H DAH VALUE 52H 4FH 4EH 49H 43H 20H 44H 45H 53H 49H 47H 4EH 53H 20H 49H 4EH 43H 4FH 52H 50H 4FH 52H 41H 54H 45H 44H 20H 00H 31H 39H 39H 37H 00H FFH 1AH 05H 01H 00H 00H 40H 03H 00H FFH DESCRIPTION R O N I C SPACE D E S I G N S SPACE I N C O R P O R A T E D SPACE END TEXT 1 9 9 7 END TEXT END OF LIST CISTPL_CONF TPL_LINK TPCC_SZ TPCC_LAST TPCC_RADR TPCC_RADR TPCC_RMSK NULL CONTROL TUPLE CISTPL_END DCH 00H INVALID ADDRESS The shaded area (addresses BEH C0H C2H C4H) can be different. It represents the year of introducing the version of the card. White Electronic Designs Corp. reserves the right to change products or specifications without notice. July 2007 Rev. 6 13 White Electronic Designs Corporation * (602) 437-1520 * www.whiteedc.com White Electronic Designs PCMCIA Flash Memory Card FLA Series Document Title PCMCIA Flash Memory Card FLA Series Revision History Rev # History Release Date Status Rev 0 Initial Release April 2007 Final Rev 6 1.0 Update absolute maximum ratings commercial temperature to 0C to +60 C from 30C to +80 C July 2007 Final White Electronic Designs Corp. reserves the right to change products or specifications without notice. July 2007 Rev. 6 14 White Electronic Designs Corporation * (602) 437-1520 * www.whiteedc.com