Automation & Sensing OI Touchscreens Selection Guide........................................... 166 PS6R Standard Series................................. 167 Part Numbers................................................. 167 Specifications................................................. 168 Dimensions.................................................... 170 PLCs PS5R-V Series............................................. 174 Part Numbers................................................. 174 Specifications................................................. 175 Dimensions.................................................... 178 Automation Software PS5R Slim Line Series................................. 182 Part Numbers................................................. 183 Specifications................................................. 184 Dimensions and Terminal Markings.............. 186 PS5R Standard Series................................. 188 Part Numbers................................................. 188 Specifications................................................. 189 Dimensions.................................................... 192 Power Supplies Power Supplies PS3X Series................................................. 193 Part Numbers................................................. 193 Specifications................................................. 194 Dimensions.................................................... 196 Safety Precautions......................................... 198 Sensors Communication www.IDEC.com/powersupply Barriers Table of Contents LED Lighting - Pg. 1 Automation & Sensing - Pg. 21 Safety - Pg. 281 Switching & Controls - Pg. 483 Index - Pg. 1039 Power Supplies OI Touchscreens Selection Guide Selection Guide Series PS6R PS5R-V PS5R Slim Line PS5R PS3X PS3L 167 174 182 188 193 Visit www.IDEC.com/ powersupply PLCs Appearance Page Automation Software Housing Metal Power Supplies Metal Direct or DIN Rail mount Panel or bracket mount DIN Rail Wattage Range 120W to 480W 7.5W to 240W 10W to 240W 7.5W to 480W 15W to 100W 10W to 300W Input Voltage 100 to 240 V A, 110 to 350V DC 85 to 264V AC, 100 to 370V DC 85 to 264 V AC, 100-370 V DC (100-350V DC, 120W & 240W) 85 to 264V AC, 105 to 370V DC 85 to 264V AC, 120 to 375V DC 85 to 264V AC, 105 to 370V DC 5V DC 2A 1.5A, 2.0A 2.0A 1.5A, 2.5A 3A, 5A, 12A, 16A 2A, 3A, 6A 12V DC 1A 0.6A, 1.3A, 2.5A 1.2A, 2.5A 0.6A, 1.2A, 2.5A 1.3A, 2.1A, 4.2A, 6A, 8.5A 0.90A, 1.4A, 2.5A, 4.3A, 8.5A, 13A 24VDC 5A, 10A, 20A 0.3A, 0.65A, 1.3A, 2.5A, 3.75A, 5.0A, 10.0A 0.65A, 1.3A, 2.5A, 3.75A, 5A, 10A 0.30A, 0.60A, 1.3A, 2.1A, 3.1A, 4.2A, 5A, 10A, 20A 0.63A, 1.1A, 2.2A, 3.2A, 4.5A 0.50A, 0.70A, 1.3A, 2.2A, 4.5A, 6.5A, 12.5A up to 77% 69% 69% 77% 70-75% up to 85% 75%, 78% 73% to 75% 81% to 82% 74% to 80% up to 90% 80% to 84% 75% to 91% 82% to 84% 78% to 82% Output Current Ratings Typical Efficiency 12V DC up to 93% 24V DC DIN Rail or surface mount +/-10% (+/- 5% for 90W) Voltage Adjustments +/-10% Ripple Voltage 1.5%peak to peak max (including noise) - Overvoltage Protection (input) 120% - Overcurrent Protection (output) 105 to 120% (auto reset) Operating Temperature -10 to +70C (14 to 140F) Termination 105% minimum (101% for 90W), auto reset -25C to +75C +/-10% (V.ADJ control on front) 2% peak to peak max (including noise) 120% or more, auto reset 105% min shutdown 120% typical -10 to +70C (14 to 140F) M3.5 phillip/slotted, spring loaded, captive (fingersafe) ANSI/ISA-12.12.01-2011 Listed File#E234997 ANSI/ISA-12.12.01-2011 Listed File#E234997 - 160mV maximum 115% typical 120% typical -10 to +85C -10 to +60C (14 to 140F) 105% minimum (Zener or auto reset) M3 or M3.5 UL508 Listed File #E177168 Communication Metal Mounting 5V DC Sensors Plastic DIN Rail or surface mount; 6 direction IEC Style screw terminals (fingersafe) UL508 Listed File #E177168 ANSI/ISA-12.12.01-2011 Listed File#E234997 Cert No. BL980213332392 Approvals Barriers (SEMI F47 120W & 240W only) 166 www.IDEC.com 1706131649 Power Supplies PS6R Series OI Touchscreens PS6R Series Switching Power Supplies Expandable and space-saving switching power supplies. High efficiency reduces operation costs. * * * * * * * 60mm 37mm Applicable Standards Mark UL508 CSA C22.2 No. 107.1 C US LISTED Automation Software * * * * PLCs * * * 93% efficiency Plug-in output modules for additional output voltages Plug-in branch terminal module for additional terminals Power Range: 120W, 240W, 480W Input voltage: 100 to 240V AC (voltage range: 85 to 264V AC/110 to 350V DC) Up to 70C (158F) operating temperature DC low LED indicator and output contact The terminals are captive spring-up screws. Ring or fork terminals can be used. Finger-safe construction prevents electric shocks. Panel mount bracket and side-mount panel mounting bracket. Can be attached to a DIN rail or directly to a panel surface. RoHS compliant UL listed for Class 1, Division 2 Hazardous Locations Meets SEMI F47 Sag Immunity ABS Certified for maritime use 85mm File No. or Organization UL/c-UL Listed File No. E177168 TUV SUD EN60950-1 EN50178 EN61204-3 Power Supplies EU Low Voltage Directive EMCD Part Numbers PS6R Output Capacity* Accessories Part No. PS6R-F24 240W PS6R-G24 480W PS6R-J24 Output Current 5A 85 to 264V AC 21.6 to 26.4V Item Output Voltage Expansion Module Note 1 10A 20A *Output voltage x output current = output capacity Part No. Note PS9Z-6RM1 Output: +5V, 2A, 10W PS9Z-6RM2 Output: +12V, 1A, 12W PS9Z-6RM3 Output: +5V, 1A/-5V, 1A, 10W PS9Z-6RM4 Output: +15V, 0.4A/-15V, 0.4A, 12W PS9Z-6RM5 Output: +5V, 1A/+12V, 0.5A, 11W PS9Z-6RM6 Output: +12V, 0.5A/-12V, 0.5A, 12W PS9Z-6RS1 Additional screw terminals for wiring: 2 + terminals / 2 - terminals Sensors 120W Input Voltage Output Voltage Branch Terminal Module Note 2 PS9Z-6R1F DIN Rail End Clip BNL6 PS9Z-6R2F BNDN1000 Communication Panel Mounting Bracket Side-mount Panel Mounting Bracket DIN Rail Supplied with M3 x 6 countersunk mounting screws 1,000mm 1. When using an output voltage expansion module, reduce 1A from the output current of PS6R. 2. When using a branch terminal module, the total voltage/current of PS6R and the branch terminal module should not exceed the rated current/voltage of PS6R Barriers 120W shown with Branch Terminal module attached. 1706131649 800-262-IDEC (4332) * USA & Canada 167 Power Supplies OI Touchscreens PS6R Series Specifications PS6R Part No. PS6R-F24 Input Voltage Frequency 100V AC 230V AC 100V AC Inrush Current 230V AC 120V AC Leakage Current 230V AC 100V AC Efficiency (Typical) 230V AC Power Factor 100V AC (Typical) 230V AC Rated Voltage/Current Adjustable Voltage Range Output Holding Time Start Time Rise Time Output Automation Software PLCs Input Input Current Total Fluctuation Regulation Dielectric Supplementary Strength Functions Power Supplies Sensors PS6R-J24 5% max. Input Fluctuation Load Fluctuation Temperature Change Ripple (including noise) Communication PS6R-G24 100 to 240V AC (Voltage range: 85 to 264V AC/110 to 350V DC) (Load 80% at 85 to 100V AC, 110 to 140V DC) Note 1 50/60Hz 1.4A typ 2.7A typ 5.5A typ. 0.7A typ 1.2A typ 2.3A typ. 9A max. (Ta=25C, 100V AC cold start) 20A max. (Ta=25C, 230V AC cold start) 0.5mA max. 1mA max. 90% 90% 91% 90% 91% 93% 0.99 0.99 0.98 0.96 0.97 0.97 24V/5A 24V/10A 24V/20A 10% 20ms min. (at rated input and output) 800ms max. (at rated input and output) 200ms max. (at rated input and output) 0.4% max. 0.6% max. 0.05%/oC max. (-10 to +60C) 1% p-p max. (0 to +60C) 1.5% p-p max. (-10 to 0C) Overcurrent Protection 105 to 120% (auto reset) (output current when voltage drops by 5%) Overvoltage Protection Output off at 120% Note 2 Operation Indicator LED (green) Voltage Low Indication LED (amber) Between input and output terminals Between input and ground terminals Between output and ground terminals 3000V AC, 1 minute 2000V AC, 1 minute 500V AC, 1 minute 100M min. 500V DC megger (between input and output terminals/between input and ground terminals) Insulation Resistance (at room temperature and normal humidity) Operating Temperature -10 to +70C (no freezing) Note 3 Operating Humidity 20 to 90% RH (no condensation) Storage Temperature -25 to +75C (no freezing) Storage Humidity 20 to 90% RH (no condensation) 10 to 55 Hz, amplitude 0.375 mm (0.187mm using PS9Z-6R1F) Vibration Resistance 2 hours each in 3 axes, 6 directions Shock Resistance 300 m/s2 (150 m/s2 when using a PS9Z-6R1F panel mounting bracket) EMI EN61204-3 (Class B) EMC EMS EN61204-3 (industrial) Degree of Protection IP20 (IEC 60529) Weight (approx.) 630g 960g 1400g Terminal Screw M3.5 (See last page for wire sizes) 1. DC input voltage is not subjected to safety standards. 3. See the output derating curves. 2. One minute after the output has been turned off, turn on the input again. Easily Expandable Branch Terminal Module Output Voltage Expansion Module Two terminals can be added. No wiring is required, reducing installation space. Barriers In addition to the standard 24V output, additional 5, 12, and 15V outputs can be added. 168 www.IDEC.com 1706131649 Power Supplies PS6R Series Accessories (For use with PS6R) PS9Z-6RM1 Input Voltage Output Capacity 10W max. 12W max. 5V/2A 12V/1A Rated Voltage/Current Supplementary Functions PS9Z-6RM4 24V DC 10W max. 12W max. 5V 2A 15V 0.4A 11W max. 5V/1A, 12V/0.5A 100mV max. 150mV max. PS9Z-6RS1 12W max. -- 12V 0.5A 24V/10A max. Note 1 -- -- -- 0.05%/max. (-10 to +60C) 100mV max., 150mV max. Overcurrent Protection 105% (auto reset) Overvoltage Protection Output off at 120% -- Shock Resistance EMI EMS Power Supplies Safety Standards Degree of Protection Weight (approx.) Terminal Screw Automation Software -10 to +70C (no freezing) Note 2 20 to 90%RH (no condensation) -25 to +75C (no freezing) 20 to 90% RH (no condensation) 10 to 55 Hz, amplitude 0.375 mm, 2 hours each in 3 axes, 6 directions (in combination with PS6R-J24) 300 m/s2 (150 m/s2 when using a PS9Z-6R1F panel mounting bracket), 3 shocks each in 6 axes (in combination with PS6R-J24) EN61204-3 (Class B) (in combination with PS6R-24) -- EN61204-3 (industrial) (in combination with PS6R-24) UL508 (Listing), CSA C22.2 No.107.1, IEC/EN60950-1, EN50178 (in combination with PS6R-24) IP20 (IEC 60529) 90g 30g M3.5 (See last page for wire sizes.) Operating Temperature Operating Humidity Storage Temperature Storage Humidity Vibration Resistance EMC Branch Terminal Module PS9Z-6RM5 PS9Z-6RM6 Not available 5% max. 200 ms max. (at rated input and output) 0.5% max. 1.0% max. Regulation Output PS9Z-6RM3 PLCs Adjustable Voltage Range Voltage Accuracy Start Time Input Fluctuation Load Fluctuation Temperature Change Ripple (including noise) PS9Z-6RM2 OI Touchscreens Output Voltage Expansion Module Part No. 1. Ensure that the current does not exceed the rated current of the PS6R. 2. See the output derating curves. 96 Operates without derating at 0 to 60C 94 PS6R-J24 Competitor A Competitor B Efficiency (%) 92 Operates at -10 to 70C 90 88 86 84 82 0 10 20 30 40 50 60 70 80 Operating Temperature (C) 50 100 150 200 250 Communication 100 90 80 70 60 50 40 30 20 10 0 -10 Energy-saving 93% Efficiency (480W) Sensors Output Current (%) Wide Operating Termperature Range 300 Input Voltage (V AC) Easy Maintenance - LED Indicator Status Normal Overload or Input Voltage Low* Output short-circuit Output OFF DC ON (green LED) Barriers DC Low (amber LED) *The LEDs turn on when the input voltage drops. 1706131649 800-262-IDEC (4332) * USA & Canada 169 Power Supplies Dimensions (mm) PS6R-G24 PS6R-F24 PS6R-J24 125 4 125 A A 4 10-M3.5 Terminal Screws A A 125 4 9.3 A A 9.3 8 - M3.5 Terminal Screws 6 - M3.5 Terminal Screws PS9Z-6R1F Panel Mounting Bracket A 44.9 35.3 125 A 130.6 145 28 28 39 Panel cut-out (Front view) PS9Z-6R2F (Side-mount Panel Mounting Bracket) When a PS9Z-6R2F is installed on PS6R 4-M4 or o4-4.5 holes 56 (Side view) 4-M4 or 4-o4.5 holes C B D 148.6 138.5 148.6 56 When using a PS9Z-6RM* Output Voltage Expansion Module Panel cut-out (Front view) (Side view) Mounting Screws (M3 x 6 countersunk screw) When using a PS9Z-6RS1 Branch Terminal Module Dimension Table Mounting Screws 170 107.2 Mounting Screws 27.8 9.6 A B C D E PS6R-F24 - 39.3 29.5 29.5 58 PS6R-G24 10.5 62.3 29.5 31 81 PS6R-J24 23 87.3 29.5 31 106 34.4 53 59 59 Barriers 9.3 Communication 56 70 11.8 Sensors 138.5 11.8 Power Supplies 10 135 135 145 Automation Software A = 9.5 When a PS9Z-6R1F is installed on PS6R 4-M4 or o4-4.5 holes 28 3.8 A A A A A A 85 A = 9.5 4.5 60 106.5 35.3 125 106.5 3.8 A A A A 10 3.8 A = 9.5 4.5 37 4.5 PLCs 35.3 125 106.5 44.9 44.9 9.3 OI Touchscreens PS6R Series 21 33.4 www.IDEC.com E 1706131649 Power Supplies PS6R Series OI Touchscreens Operating Instructions o3.6 min.(reference) Applicable Crimp Terminal The PS6R should be placed in a proper enclosure. It is designed to be used with general electrical equipment and industrial electric devices. 6.6 max. 4 max. Operation Notes 1. Output interruption may indicate blown fuses. Contact IDEC. 2. The PS6R contains an internal fuse for AC input. When using DC input, install an external fuse or DC input. To avoid blown fuses, select a fuse in consideration of the rated current of the internal fuse. Rated Current of Internal Fuses Internal Fuse Rated Current PS6R-F24 4A PS6R-G24 6.3A PS6R-J24 10A * Recommended tightening torque of the input and output terminals is 0.8N*m. * The output voltage can be adjusted within 10% of the rated output voltage by using the V.ADJ control. Note that overvoltage protection may work when increasing the output voltage. * When large shocks or heavy vibrations on the PS6R are expected, the use of DIN rail or PS9Z-6R2F side-mount panel mounting bracket is recommended. Series Operation The following series operation is allowed. Connect Schottky barrier diodes as shown below. Output voltage expansion modules cannot be connected in series. L N -- Avoid overload and short-circuit for a long period of time, otherwise internal elements may be damaged. -- DC input operation is not subjected to safety standards. L N +V -V L N +V -V Load L N L N +V -V L N +V -V Load Load Automation Software Installation Notes (b) (a) * The PS6R can be installed in the direction shown below only. Select a Schottky diode in consideration of the rated current. The diode's reverse voltage must be higher than the PS6R's output voltage. Parallel Operation Parallel operation is possible to increase the output capacity. Output voltage expansion modules cannot be connected in series. Up L N When using PS9Z-6R1F Panel Mounting Bracket When using PS9Z-6R2F Side-mount Panel Mounting Bracket Terminal Wire Size/No. of Wire Input PS6R-F24 Output PS6R-G24 DC OK Output Input Wire Type 18-14 AWG, 1-wire 18-14 AWG, 1-wire, (18 AWG - 7A, 16 AWG - 10A, 14 AWG - 15A) 22-14 AWG, 1-wire (stripped wire length: 6 to 7mm) 18-14 AWG, 1-wire 12 AWG, 1-wire PS9Z-6R0 Output 22-14 AWG, 1-wire (stripped wire length: 6 to 7mm) 18-14 AWG, 1-wire (18 AWG - 7A, 16 AWG -10A, 14 AWG - 15A) +V -V When increasing the capacity, observe the following. 1. Maintain the operating temperature below 40C. 2. Output cannot be connected directly in parallel operation. Connect a diode to the output of each PS6R. 3. Output terminal voltage of both power supplies must be the same. Also, maintain the voltage difference between the power supplies below 30mV. 4. Use load lines of the same diameter and length. 5. Set the output voltage higher for the amount of diode forward voltage drop. 6. Turn on the inputs at the same time. 7. Select a diode in consideration of: Diode's reverse voltage must be higher than the PS6R's output voltage. Diode's current must be three times the PS6R's output current. Provide a heat sink for heat dissipation. 7.0 (0.8) Communication PS6R-J24 Output L N Load Copper Solid/Stranded 18-14 AWG, 2-wire Use the same size wire for each terminal (18 AWG - 7A, 16 AWG - 10A, 14 AWG - 15A) DC OK Output Torque, in-ibs (Nm) +V -V Sensors * Do not close the top and bottom openings of the PS6R to allow for heat radiation by convection. * Maintain a minimum of 20mm clearance around the PS6R, except for the top and bottom openings. * When derating of the output does not work, provide forced air-cooling. * Make sure to wire the ground terminal correctly. * For wiring, use wires with heat resistance of 60C or higher. Use copper wire of the following sizes. Wires of the following sizes must be used to comply with UL508, CSA C22.2 No. 107.1. L N Power Supplies Vertical Model PLCs Part No. 5.5 min. Copper Solid/Stranded Use with UL-listed ring/ fork crimp terminal. Copper Solid/Stranded -- 7.0 (0.8) Barriers 1706131649 800-262-IDEC (4332) * USA & Canada 171 Power Supplies OI Touchscreens PS6R Series PS9Z-6RM3/M4/M6 Output Voltage Expansion Module PS6R-6RM1/M2/M3 Output Voltage Expansion Module PS6R-6RS1 Branch Terminal Module PLCs PS6R-J24 (PS6R-6RM5 shown) PS6R-24/PS9Z-6RS1 Name Voltage range: 85 to 264V AC/110 to 350V DC Ground Terminal Be sure to connect this terminal to a proper ground. +V, -V DC Output Terminals +V: Positive output terminal -V: Negative output terminal VR.ADJ Output Voltage Adjustment Allows adjustment within 10%. Turning clockwise increases the output voltage. DC ON Operation Indicator (green) Lights on when the output voltage is on. DC LOW Output Low Indicator (Amber) Lights on when the output voltage drops approximately 80% of the rated value. DC OK DC OK Output Lights on when the output voltage is more than 80% of the rated value. NPN transistor output (50V DC max., 50 mA max.) Name Description +5V, +12V, +15V DC Output Terminal +5V side, +12V side, +15V side -5V, -12V, -15V DC Output Terminal -5V side, -12V side, -15V side COM DC Output Terminal 0V side (wired internally to -V of PR6R-J24) Characteristics Operating Temperature vs. Output Current (Derating Curves) Overcurrent Protection Characteristics Overcurrent Protection Characteristics PS9Z-6RM* PS6R-24 Output Current vs. Input Voltage (Derating Curves) (Ta=25C) 0 10 20 30 40 50 Operating Temperature (C) 60 Input Voltage(V) 264 350 120% 95% F24 Output Voltage (%) 100 90 80 70 60 50 40 30 20 10 0 70 (ACV) 85 100 (DCV) 110 140 105% 100 Output Current (%) 100 90 80 70 60 50 40 30 20 10 0 -10 24 G24 J24 Pulse Current (Approx. 30A rms, 40A peak) 0 0 Input Current (%) 100 Operating Temperature approved by Safety Standards UL508, CSA C22.2 No. 107. 1 EN60950-1, EN50178 PS6R-F24 60C 60C PS6R-G24 60C 60C PS6R-J24 55C 60C PS9Z-6R 55C 60C Part No. Barriers Description Input Terminal PS9Z-6RM Marking Output Current (%) Communication Sensors Power Supplies Automation Software Marking L, N 172 www.IDEC.com 1706131649 Power Supplies PS6R Series PS6R-J24 PS6R-6RM1/M2/M3 Output Voltage Expansion Module PS9Z-6RM3/M4/M6 Output Voltage Expansion Module OI Touchscreens Parts Description PS6R-6RS1 Branch Terminal Module PLCs (PS6R-6RM5 shown) Automation Software PS6R-24/PS9Z-6RS1 Name Description L, N Input Terminal Voltage range: 85 to 264V AC/110 to 350V DC Ground Terminal Be sure to connect this terminal to a proper ground. +V, -V DC Output Terminals +V: Positive output terminal -V: Negative output terminal VR.ADJ Output Voltage Adjustment Allows adjustment within 10%. Turning clockwise increases the output voltage. DC ON Operation Indicator (green) Lights on when the output voltage is on. DC LOW Output Low Indicator (Amber) Lights on when the output voltage drops approximately 80% of the rated value. DC OK DC OK Output Lights on when the output voltage is more than 80% of the rated value. NPN transistor output (50V DC max., 50 mA max.) Power Supplies Marking PS9Z-6RM Marking Name Description +5V, +12V, +15V DC Output Terminal +5V side, +12V side, +15V side -5V, -12V, -15V DC Output Terminal -5V side, -12V side, -15V side COM DC Output Terminal 0V side (wired internally to -V of PR6R-J24) 105% 100 0 10 20 30 40 50 Operating Temperature (C) 60 70 Input Voltage(V) Operating Temperature approved by Safety Standards UL508, CSA C22.2 No. 107. 1 EN60950-1, EN50178 PS6R-F24 60C 60C PS6R-G24 60C 60C PS6R-J24 55C 60C PS9Z-6R 55C 60C 24 G24 J24 Pulse Current (Approx. 30A rms, 40A peak) 0 0 800-262-IDEC (4332) * USA & Canada Input Current (%) 100 Barriers 1706131649 Part No. 264 350 120% 95% F24 Output Voltage (%) 100 90 80 70 60 50 40 30 20 10 0 (ACV) 85 100 (DCV) 110 140 Overcurrent Protection Characteristics PS6R-24 Overcurrent Protection Characteristics PS9Z-6RM* Output Current (%) 100 90 80 70 60 50 40 30 20 10 0 -10 Output Current vs. Input Voltage (Derating Curves) (Ta=25C) Communication Output Current (%) Operating Temperature vs. Output Current (Derating Curves) Sensors Characteristics 173 Power Supplies PS5R-V Series OI Touchscreens PS5R-V Series Switching Power Supplies DIN-rail mount switching power supplies with global approvals for both industrial and hazardous locations Key Features PLCs * Compact size preserves panel space * Slim size (width): 22.5mm (10W/15W/30W) 36mm (60W/90W) 45mm (7.5W) 46mm (120W) 60mm (240W) * Universal Voltage Input: 85-264V AC/100-370V DC * Wide operating temperature range * Spring-up terminals accept ring & fork terminals * Approved for use in Class I Division 2 hazardous locations * Can be installed in 6 directions * 7.5W ~ 90W meet NEC Class 2 output ratings * Overcurrent protection with auto-reset * Meets SEMI F47 Sag Immunity (208V AC input) * RoHS compliant * Five-year factory warranty Power Supplies Automation Software Standards Compliance Applicable Standards UL/c-UL Listed File No. E467154, E177168 TUV SUD EN60950-1 EN50178 EN61204-3 EN50581 EU Low Voltage Directive, EMC Directive RoHS Directive -- SEMI F47 EPRI Note 1: PS5R-VA/VB/VC/VD/VE only Note 2: EN60950-1, EN50178 only Part Numbers 7.5W Sensors File No. or Organization UL508 UL13101 ANSI/ISA 12.12.01 CSA C22.2 No.107.1 CSA C22.2 No.213 CSA C22.2 No.2231 Output Capacity 10W 15W Part Number Output Voltage Output Current PS5R-VA05 5V 1.5A PS5R-VA12 12V 0.6A PS5R-VA24 24V 0.3A PS5R-VB05 5V 2.0A PS5R-VB12 12V 1.3A 24V 0.65A PS5R-VB24 PS5R-VC12 Input Voltage 100 to 240V AC (Voltage range: 85 to 264V AC / 100 to 370V DC) 12V 2.5A PS5R-VC24 24V 1.3A 60W PS5R-VD24 24V 2.5A 30W Communication Mark 90W PS5R-VE24 24V 3.75A 120W PS5R-VF24 24V 5.0A 240W PS5R-VG24 24V 10.0A Part Number Structure PS5R - V Output Capacity Output Voltage Barriers A: 7.5W 05: 5V3 B: 10W/15W 12: 12V4 C: 30W 24: 24V D: 60W E: 90W Note 3: PS5R-VA/VB only F: 120W Note 4: PS5R-VA/VB/VC only G: 240W Use only for interpreting part numbers. Do not use for developing part numbers. 174 www.IDEC.com 1706131649 Power Supplies PS5R-V Series Specifications 5V DC output 12V DC output 24V DC output PS5R-VA05 PS5R-VA12 PS5R-VA24 PS5R-VB05 PS5R-VB12 PS5R-VB24 PS5R-VC12 PS5R-VC24 7.5W 15W (5V Model is 10W) 30W 100V AC 5V: 0.20A 12V, 24V: 0.18A 230V AC 5V: 0.12A 12V, 24V: 0.10A 5V:0.25A 12V, 24V: 0.35A 5V:0.14A 12V, 24V: 0.19A 100V AC 15A 230V AC 120V AC 230V AC 36A 100V AC 5V: 74%, 12V: 79%, 24V: 80% Output Capacity Rated Input Voltage (Single-phase two-wire)1 PS5R-VD24 60W 90W 100 to 240V AC (Voltage range: 85 to 264V AC/100 to 370V DC) (Load 80% at 100-105V DC) Frequency Input Input Current (Typ.) Inrush Current (Typ.) (Ta=25C, cold start) Efficiency (Typ.) (at rated output)2 Power Factor (Typ.) 2.7A 0.8A 0.6A 0.7A 1.2A 18A 14A 45A 41A 30A 0.99 0.92 0.96 5V/1.5A, 12V/0.6A, 24V/0.3A 5V/2.0A3, 12V/1.3A, 24V/0.65A 12V/2.5A, 24V/1.3A 24V/2.5A 24V/3.75A 24V/5A 24V/10A 12V: 13ms, 24V: 15ms 13ms 5% 20ms 12V: 110ms 24V: 110ms 105ms 285ms Temperature Change Ripple (including noise) Between input and output terminals Between input and ground terminals 600ms max. 10% 30ms 30ms 800ms max. 33ms 40ms 700ms max. 800ms max. 0.05%/C max. (-25 to +55C ) 0.05%/C max. (-25 to +50C) 200ms max. 5V, 12V: 200ms max. 24V: 250ms max. 0.4% max. 5V: 2.5% max. 12V, 24V: 1.0% max. 0.04%/C max. (-10 to 12V: 0.05%/C max. (-10 to +50C) 0.05%/C max. 0.05%/C max. (-10 to +65C ) +65C ) 24V: 0.05%/C max. (-10 to +55C) (-10 to +55C ) 5V: 8% p-p max. (-25 to -10C) 5V: 8% p-p max. (-25 to -10C) 12V: 6% p-p max. (-25 to -10C) 12V: 6% p-p max. (-25 to -10C) 12V: 6% p-p max. (-25 to -10C) 24V: 4% p-p max. (-25 to -10C) 24V: 4% p-p max. (-25 to -10C) 24V: 4% p-p max. (-25 to -10C) 5V: 5% p-p max. (-10 to +0C) 5V: 5% p-p max. (-10 to +0C) 12V: 2.5% p-p max. (-10 to +0C) 12V: 2.5% p-p max. (-10 to +0C) 12V: 2.5% p-p max. (-10 to +0C) 24V: 1.5% p-p max. (-10 to +0C) 24V: 1.5% p-p max. (-10 to +0C) 24V: 1.5% p-p max. (-10 to +0C) 5V: 2.5% p-p max. (0 to +65C) 5V: 2.5% p-p max. (0 to +65C) 1% p-p max. (0 to 12V: 1.5% p-p max. (0 to +50C) 12V: 1.5% p-p max. (0 to +65C) 12V: 1.5% p-p max. (0 to +65C) 24V: 1% p-p max. (0 to +55C) +55C) 24V: 1% p-p max. (0 to +65C) 24V: 1% p-p max. (0 to +65C) 105% min. (auto reset) LED (green) 3,000V AC, 1 minute 2,000V AC, 1 minute 1.0% max. 0.05%/C max. (-10 to +50C ) 4% p-p max. (-25 to -10C) 1.5% p-p max. (-10 to +0C) 1% p-p max. (0 to +50C) 101% min. (auto reset) 1% p-p max. (0 to +55C) Power Supplies Operation Indicator 10% 5V: 53ms, 12V: 34ms, 24V: 36ms 5V: 330ms 12V: 215ms 24V: 230ms 500ms max. 89% 90% 88% 89% Automation Software 230V AC 45ms 5V, 12V: 200ms max 24V: 250ms max Output 1.4A 0.86 Input Fluctuation Load Fluctuation 1% p-p max. (0 to +50C) 105% min. (auto reset) 500V AC, 1 minute Between output and ground terminals Between input and output terminals: 100M min. (500V DC megger) Between input and ground terminals: 100M min. (500V DC megger) -25 to +75C -25 to +70C -25 to +65C Insulation Resistance Operating Temperature4 (No freezing) Operating Humidity (no condensation) 20 to 90% RH -25 to +75C 20 to 90% RH Storage Temperature (No freezing) Storage Humidity (no condensation) Shock Resistance Expected Life5 EMI EMS Safety Standards Degree of Protection 75H x 45W x 70D 130g 10 to 55Hz, amplitude 0.21mm, 2 hours each in 3 axes (when used with BNL6 end clips) 10 to 55Hz, amplitude 0.375mm, 2 hours each in 3 axes (when used with BNL8 end clips) 10 to 55 Hz, amplitude 0.375mm, 2 hours each in 3 axes (when used with part no. BNL6 mounting clips) 300 m/s2 (30G), 3 times each in 6 directions 8 years minimum (at the rated input, 50% load, operating temperature +40C, standard mounting direction) EN61204-3 (Class B) EN61204-3 (industrial) UL508 (Listing), UL1310 Class 2, ANSI/ISA-12.12.01 UL508 (Listing) ANSI/ISA-12.12.01 CSA C22.2 No. 107.1, 213, 223 EN60950-1, EN50178 CSA C22.2 No. 107.1, 213 EN60950-1, EN50178 SEMI F47 (at 208V AC input only) IP20 (EN60529) 90H x 22.5W x 95D 95H x 36W x 108D 115H x 46W x 121D 125H x 60W x 125D 140g 150g 260g 310g 470g 960g M3.5 Communication Other Standard 10 to 55Hz, amplitude 0.33mm, 2 hours each in 3 axes (when used with BNL6 end clips) 10 to 55Hz, amplitude 0.375mm, 2 hours each in 3 axes (when used with BNL8 end clips) Sensors 10 to 55Hz, amplitude 0.375mm, 2 hours each in 3 axes (when used with BNL6 end clips) Vibration Resistance Terminal Screw 1.1A 86% 86% -- -- Rise Time (at rated input and output) Regulation 0.3A 1.3A 12V: 83%, 24V: 85% 12V: 85%, 24V: 87% -- -- Overcurrent Protection Dielectric Strength 0.7A 5V: 77%, 12V: 82%, 24V: 84% 5V: 73%, 12V: 80%, 24V: 81% -- -- 500ms max. Weight (approx.) 240W 0.5mA max. 1.0mA max. Start Time (at rated input and output) Dimensions (mm) 120W 230V AC 5V: 73%, 12V: 77%, 24V: 76% -- 100V AC -- 230V AC Adjustable Voltage Range Output Holding Time 100V AC EMC PS5R-VG24 50/60 Hz Rated Voltage/Current (Typ.) (at rated output) PS5R-VF24 PLCs Leakage Current PS5R-VE24 OI Touchscreens Model *At normal temperature and humidity unless otherwise specified. Note 1: DC input voltage is not subject to safety standards. When using on DC input, connect a fuse to the input terminal for DC input protection. Note 2: Under stable state. Note 3: PS5R-VB05 (5V DC/2.0A) is 10W (Up to 3.0A at Ta = 0 to 40C. Not subject to safety standards above 2.0A.) Note 4: See the output derating curves. Note 5: Calculation of the expected life is based on the actual life of the aluminum electrolytic capacitor. The expected life depends on operating conditions. Barriers 1706131649 800-262-IDEC (4332) * USA & Canada 175 Power Supplies Characteristics Operating Temperature vs. Output Current (Derating Curves) Conditions: Natural air cooling (Operating temperature is the temperature around the switching power supply.) PS5R-VA05, -VA12, -VA24 PS5R-VB05, -VB12, -VB24 Mounting A,E 90 90 Output Current (%) 80 70 60 50 40 Mounting B, C, D, F 30 20 10 0 -30 -20 -10 0 10 20 30 40 50 60 Operating Temperature (C) 10 0 -30 -20 -10 50 30 Mounting D, E, F 20 10 0 -30 -20 -10 0 10 20 30 40 50 60 70 Operating Temperature (C) 30 40 50 60 70 80 40 30 20 Mounting B, C, D, E, F 10 0 -30 -20 -10 0 10 20 30 40 50 60 70 100 80 40 Mounting A Mounting F 10 0 -30 -20 -10 0 10 20 30 40 50 60 70 Mounting A 90 50 20 50 Operating Temperature (C) Mounting B, C, D 60 30 60 PS5R-VE24 Input Voltage: 85-100V AC 70 Input Voltage: 85-100V AC 70 80 Mounting E 70 60 50 40 Mounting B, C, D, F 30 20 10 0 -30 -20 -10 80 Operating Temperature (C) 0 10 20 30 40 50 60 Operating Temperature (C) 70 80 PS5R-VG24 100 Mounting A 100 Mounting C, E 90 90 80 Mounting E 80 70 Mounting B, D 60 50 40 Mounting A Mounting F 10 0 -30 -20 -10 0 10 20 30 40 50 60 70 Operating Temperature (C) 80 70 50 40 20 10 0 -30 -20 -10 0 10 20 30 40 50 60 90 80 80 Output Current (%) 100 70 60 50 40 30 20 10 70 80 AC DC 60 50 40 30 20 10 0 (ACV) 85 100 (DCV)100 105 264 370 70 PS5R-VA05, -VA12, -VA24, -VG24 90 Input Voltage (V) Mounting C, D, F 30 100 0 (ACV) 85 100 (DCV) 100 140 Mounting B 60 Operating Temperature (C) Input Voltage vs. Output Current (Derating Curves) Ta=25C PS5R-VB05, -VB12, -VB24, -VC12, -VC24, -VD24, -VE24, -VF24 Output Current (%) 20 Mounting E 80 80 PS5R-VF24 20 10 90 Mounting C 40 30 0 100 Output Current (%) Output Current (%) 60 Output Current (%) Automation Software 20 Operating Temperature (C) Input Voltage: 85-100V AC 70 Mounting B, C, D, E, F PS5R-VD24 90 Sensors 40 Mounting A, B 80 80 50 30 Mounting A 90 60 80 PS5R-VC24 100 Power Supplies 70 100 Input Voltage: 85-100V AC 70 Output Current (%) PLCs Output Current (%) 80 PS5R-VC12 Mounting A 100 Output Current (%) 100 Output Current (%) OI Touchscreens PS5R-V Series Input voltage (V) 264 370 PS5R-VA/VB/VC/VD/VF 100 PS5R-VG24 100 95 Output Current (%) 176 100 105 and over Output Voltage (%) Output Voltage (%) Intermittent Operation 100 95 0 -30 0 Barriers PS5R-VE24 Output Voltage (%) Communication Overcurrent Protection Characteristics Intermittent Operation 0 Intermittent Operation 0 0 Output Current (%) 100 101 and over www.IDEC.com 0 Output Current (%) 100 105 and over 1706131649 Power Supplies PS5R-V Series Operating Temperature Approved by Safety Standards OI Touchscreens UL508, CSA C22.2 No.107.1, ANSI/ISA12.12.01, EN60950-1, EN50178 Part Number Mounting B Mounting C Mounting D Mounting E Mounting F PS5R-VA05, -VA12, -VA24 65 60 60 60 65 60 PS5R-VB05, -VB12, -VB24 65 60 60 60 60 60 PS5R-VC12 50 45 45 45 45 45 PS5R-VC24 55 55 50 45 45 45 PS5R-VD24 55 40 40 40 45 35 PS5R-VE24 50 40 40 40 45 40 PS5R-VF24 55 40 45 40 45 35 PS5R-VG24 50 35 30 30 45 30 PLCs Mounting A Mounting Style Mounting B (Upright) Mounting A (Vertical, standard) Mounting C (Right side up) Mounting E (Upside down) Mounting D (Left side up) Automation Software Up Mounting F (Downward) Front Panel PS5R-VA PS5R-VB/VC PS5R-VD/ VE/VF L N Marking Name Description L, N AC Input Terminal Voltage range: 85 to 264V AC/100 to 370V DC Ground Terminal Be sure to connect this terminal to a proper ground. INPUT 50/60Hz +V, -V DC Output Terminals +V: Positive output terminal -V: Negative output terminal DC ON VR.ADJ Output Voltage Adjustment Allows adjustment within 10%. (VE = 5%) Turning clockwise increases the output voltage. Turning counterclockwise decreases the output voltage. DC ON Operation Indicator (green) Illuminates when the output voltage is on. 100 -240 VAC ON VR. ADJ VR . ADJ Power Supplies INP U T PS5R-VG OUTPUT Sensors -V +V O U TP U T Accessories Panel Mounting Bracket2 Applicable Switching Power Supply PS5R-VG Remarks -- For side mounting PS9Z-5R1C -- PS9Z-5R1E -- PS9Z-6R1F -- PS9Z-6R2F For side mounting Communication PS5R-VB PS5R-VC PS5R-VD PS5R-VE PS5R-VF Part Number PS9Z-5R1B PS9Z-5R2B Note 2: Used when installing on a panel directly, PS5R-VA model does not require panel mounting bracket. DIN Rail (35mm-wide) 1000mm BNDN1000 Aluminum End Clip Barriers Part Number BNL6 BNL8 1706131649 800-262-IDEC (4332) * USA & Canada 177 Power Supplies Dimensions (mm) PS5R-VA PS5R-VA PS5R-VB/VC 5-M3.5 Screw Terminal 27.3 61.6 4.4 5 7.35 3.8 9.5 22.5 PS5R-VD/VE 3.8 PS5R-VF 108 8.5 5-M3.5 Screw Terminal 11.5 11.5 121 44.9 24.9 35.3 98 115 35.3 95 4.5 20 36 3.8 4.5 Power Supplies 5-M3.5 Screw Terminal 8 10 10 79 Automation Software 90 19.9 35.3 75 PLCs 26 35 38.5 45 23 46 PS5R-VG 44 .9 1,150,000H minimum PS5R-VB: 900,000H minimum PS5R-VC: 650,000H minimum PS5R-VD: 450,000H minimum PS5R-VE: 380,000H minimum PS5R-VF: 350,000H minimum PS5R-VG: 290,000H minimum MIL-HDBK-217FN2 (GB, 30C) *MTBF stands for Mean Time Between Failure, which is calculated according to statistical device failures, and indicates reliability of a device. It is the statistical representation of the likelihood of the unit to fail and does not necessarily represent the expected life of a product. 4 .5 3 .8 PS5R-VA: Barriers 60 12 5 35 .3 10 6 .5 Sensors 9.5 9.5 9.5 9.5 3.8 MTBF* 5.5 1 25 9 .3 8-M3.5 Screw Terminal 9.5 9.5 Communication 95 12.2 8.2 6 35.3 70 6-M3.5 Screw Terminal 62.5 60 OI Touchscreens PS5R-V Series * 3-Phase 178 www.IDEC.com 1706131649 Power Supplies When installed on switching power supply OI Touchscreens PS9Z-5R1B 13.6 Panel Mounting Bracket PS5R-V Series 12 24.7 12 PS9Z-5R2B Side-mount 16.4 Mounting hole layout when installing on a panel directly Front View 96.7 Side View 10.0 120 112 112 2-M4 or 2- o 4.5 holes 2-M4 or 2- o 4.5 holes 28.8 5.5 102 10.0 110 102.0 PLCs Mounting hole layout when installing on a panel directly 44 62.9 Side View 10.2 109.8 105 115 105 2-M4 or 2- o 4.5 holes Automation Software PS9Z-5R1C Front View 26 26 38 PS9Z-5R1E 9.9 Mounting hole layout when installing on a panel directly Front View Side View 125 10.2 122.8 Power Supplies 135 125 2-M4 or 2- o 4.5 holes 10.5 4-M4 or 4- o 4.5 holes 130.6 10.5 145 135 145 135 Sensors 28 Side View 10 PS9Z-6R1F Front View 9.9 36 36 48 Mounting hole layout when installing on a panel directly Mounting hole layout when installing on a panel directly 28 PS9Z-6R2F Side-mount Side View Front View 4-M4 or 4- o 4.5 holes 29.5 62.3 31 138.6 148.6 138.6 11.8 56 Communication 28 39 56 11.8 56 70 Side View 1706131649 Barriers Mounting hole layout for side mounting 800-262-IDEC (4332) * USA & Canada Back View Mounting Screws (4 -M3x6 countersunk screws) 179 Power Supplies Power Supplies Automation Software PLCs OI Touchscreens PS5R-V Series Mounting on DIN Rails Safety Precautions The PS5R-V should be placed in a proper enclosure. It is designed to be used with general electrical equipment and industrial electric devices * Do not use switching power supplies with electric equipment whose malfunction or inadvertent operation may damage the human body or life directly. * Make sure that the input voltage and output current do not exceed the ratings. If the input voltage and output current exceed the ratings, electric shock, fire, or malfunction may occur. * Do not touch the terminals of the switching power supply while input voltage is applied, otherwise electric shock may occur. * Provide the final product with protection against malfunction or damage that may be caused by malfunction of the switching power supply. * Operating temperatures should not exceed the ratings. Be sure to note the derating characteristics. If the operating temperature exceeds the ratings, electric shock, fire, or malfunction may occur. * Blown fuses indicate that the internal circuits are damaged. Contact IDEC for repair. Do not just replace the fuse and reoperate, otherwise electric shock, fire, or malfunction may occur. * Do not use the switching power supplies to charge rechargeable batteries. * Do not overload or short-circuit the switching power supply for a long period of time, otherwise the internal elements may be damaged. * Do not disassemble, repair, or modify the power supplies, otherwise the high voltage internal part may cause electric shock, fire, or malfunction. * The fuse inside the PS5R-V switching power supply is for AC input. Use an external fuse for DC input. 1. Use a 35mm-wide DIN rail. 2.Place the PS5R-V on the DIN rail as shown with input terminal side up (), and press the PS5R-V towards the DIN rail (). Make sure that the PS5R-V is installed firmly. 3. Use BNL6 end clips to ensure power supplies do not slide off the end of the DIN rail. Use of BNL8 end clips is recommended when excessive vibration or shock is anticipated. Removal * Insert a flat screwdriver into the slot in the clamp, and pull out until it clicks (). The lock mechanism is released and the PS5R-V can be removed (). When mounting the PS5R-V again, push in the latch first. Mounting Removal Clamp Installing a Panel Mounting Bracket Panel Mounting Bracket (PS9Z-5R1, PS9Z-6R1F) Tab Power Supply Notes for installation Install the tab on the panel mounting bracket into the slot on the power supply. Install the brackets as shown on the left. Ensure that the panel mounting bracket is locked by the latch. Sensors LOCK 10mm minimum * When the derating voltage may exceed the recommended value, provide forced air-cooling. * Make sure to wire the ground terminal correctly. * For wiring, use wires of heat resistance of 60oC or higher (PS5R-VB: 80oC or higher). Use copper wire of the following sizes, according to the rated current. Communication UNLOCK Latch Terminal Wire Size (allowable current) Input AWG 18 to 14 Output AWG18 to 14 (AWG18: 7A, AWG16: 10A, AWG14: 15A) Panel Mounting Bracket (PS9Z-5R2B) UNLOCK Copper Solid/Stranded Power Supply Latch Cross-Sectional are AWG18: 0.82mm2, AWG16: 1.31mm2, AWG14: 2.0mm2 Push in the latch to LOCK position. 5.5 min. * Recommended tightening torque of the input and output terminals is 1.0 to 1.3Nm (0.8N*m for UL). 180 Insert the tab on the panel mounting bracket into the slot on the power supply. o3.6min. 6.6 max. 4 max. Pull out the latch to UNLOCK position. LOCK Tab Wire Type Applicable crimp terminal (reference) Barriers Push in the latch to LOCK position. LOCK Operating Instructions * Do not close the top or bottom openings of the PS5R-V to allow for heat radiation by convection. * When mounting multiple PS5R-V switching power supplies side by side, maintain a minimum of 10 mm clearance. Observe the derating curves in consideration of the ambient temperature. Slot www.IDEC.com Ensure that the panel mounting bracket is locked by the latch. LOCK 1706131649 Power Supplies Installing PS9Z-6R2F Side-mount Panel Mounting Bracket Rust and Scratches on Metal parts Bonded metal parts are used for the PS5R-V. Rust on the edge and scratches on the surfaces may be developed depending on the storage condition, but the performance of the PS5R-V is not affected. OI Touchscreens Install the bracket on the switching power supply using four M3 x 6 countersunk screws supplied with the bracket. Recommended tightening torque is 0.5 to 0.6N.m (should be in the center positions) PS5R-V Series Panel Mounting Bracket (PS9Z-5R1, PS9Z-6R1F) Tab Slot Push in the latch to LOCK position. Noise LOCK Power Supply Small acoustic noise inside the PS5R-V may be heard depending on the input voltage and load, but the performance of the PS5R-V is not affected. UNLOCK Latch Install the tab on the panel mounting bracket into the slot on the power supply. Series Operation Install the brackets as shown on the left. Series operation is allowed. Connect Schottky barrier diodes D as shown below. Select a Schottky diode in consideration of the rated current. The diode's reverse voltage must be higher than the PS5R-V's output voltage. Ensure that the panel mounting bracket is locked by the latch. LOCK Tab Pull out the latch to UNLOCK position. LOCK L L +V UNLOCK N N -V Load L N +V -V Load L L +V N N -V L N +V -V Power Supply Latch Load Insert the tab on the panel mounting bracket into the slot on the power supply. Adjustment of Output Voltage Push in the latch to LOCK position. The output voltage can be adjusted within 10% (VE: 5%) of the rated output voltage by using the VR.ADJ control on the front. Turning the VR.ADJ clockwise increases the output voltage. Turning the VR.ADJ counterclockwise decreases the output voltage. PLCs Panel Mounting Bracket (PS9Z-5R2B) (b) (a) Ensure that the panel mounting bracket is locked by the latch. LOCK The output voltage drops automatically when an overcurrent flows due to an overload or short circuit. Normal voltage is automatically restored when the load returns to normal conditions. Insulation/Dielectric Test When performing an insulation/dielectric test, short-circuit the input (between L and N) and output (between +V and -V). Do not apply or interrupt the voltage quickly, otherwise surge voltages may be generated and the PS5R-V may be damaged. * Output interruption may indicate blown fuses. Contact IDEC. * The PS5R-V switching power supply contains an internal fuse for AC input. When using DC input, install an external fuse. To avoid blown fuses, select a fuse in consideration of the rated current of the internal fuse. Parallel Operation Parallel operation is not possible to increase the output capacity, because the internal elements and load may be damaged. Backup Operation Backup operation is a connection method of two switching power supplies in parallel for emergency. Normally one switching power supply has a sufficient output. If one switching power supply fails, another one operates to continue the output. Make sure that the sum of power consumption by load and diode is not greater than the rated wattage (rated voltage x rated current) of one switching power supply. D AC Rated Current of Internal Fuses Part Number IN Load OUT - D IN Internal FuseRated Current 2A PS5R-VD/VE/VF 4A OUT - Select a diode in consideration of: Diode's current must be more than double the PS5R-V's output current. Take heat dissipation into consideration. Sensors PS5R-VB/VC PS5R-VG Power Supplies Notes for Operation Automation Software Overcurrent Protection 6.3A * Avoid overload and short-circuit for a long period of time, otherwise the internal elements may be damaged. * DC input operation is not subject to safety standards. Warranty Scope 1706131649 800-262-IDEC (4332) * USA & Canada Barriers IDEC agrees to repair or replace the PS5R-V switching power supply if the product has been operated under the following conditions. The maximum value of output capacity is within the range shown in "Operating Temperature vs. Output Current on page 3. 1. Average operating temperature (ambient temperature of switching power supply) is 40C maximum. 2. The load is 80% maximum. 3. Input voltage is the rated input voltage. 4. Standard mounting style IDEC shall not be liable for other damages including consequential, contingent or incidental damages. Warranty does not apply if the PS5R-V switching power supply was subject to: 1. Inappropriate handling, or operation beyond specifications. 2. Modification or repair by other than IDEC. 3. Failure caused by other than the PS5R-V switching power supply. 4. Failure caused by natural disasters. Communication IDEC warranties the PS5R-V switching power supply for a period of five years from the date of shipment. 181 Power Supplies Automation Software PLCs OI Touchscreens PS5R Slim Line Series PS5R Slim Line Series Switching Power Supplies Key features: * Lightweight and compact in size * Wide power range: 10W-240W * Universal input: 10W to 90W: 85-264V AC/100-370V DC 120W and 240W: 85-264V AC/100-350V DC * Power Factor Correction for 60W to 240W (EN61000-3-2) * Meets SEMI F47 Sag Immunity (120W & 240W only) * UL Listed for Class 1, Div. 2 Hazardous Locations * Overcurrent protection, auto-reset * Overvoltage protection, shut down * Spring-up screw terminal type, IP20 * DIN rail or panel surface mount * Approvals: CE Marked ANSI/ISA-12.12.01-2011 (Hazardous locations) TUV EN50178:1997 c-UL, UL508 LVD: EN60950:2000 UL1310 (PS5R-SB, -SC, -SD) EMC: Directive EN61204-3:2000 (EMI: Class B, EMS: Industrial) Universal Input Power Power Supplies The applied input power has a range of 85-264V AC (100-350V DC) without the use of jumpers or slide switches. This makes IDEC power supplies suitable for use anywhere in the world. The indicator turns on when the output voltage drops below 80% of the rated value. This assists in troubleshooting power supply problems. Long Life Expectancy DC ON Indicator The indicator turns on when the unit is powered up. This is a convenient way to know when the power supply is receiving power. IDEC power supplies are very reliable, with a life expectancy of 70,000 hrs. (minimum) or longer, depending on usage. Power factor correction has also been included to minimize harmonic distortion, resulting in a longer operating life and increased reliability. Output Voltage Adjustment Output Channel The output voltage can be easily adjusted within + 10% of the rated voltage. With very low output ripples of less than 1% peak to peak, the 120W and 240W power supplies are some of the best in the industry. The output comes with overload protection that avoids damaging the power supply and the spring-up, fingersafe, screw terminals add a level of safety and ease for the user. The 240W power supply also has the convenience of two output terminals. Communication Sensors (SEMI F47 120W & 240W only) Designed with Accessibility & Convenience in Mind DC Low Indicator (15W, 120W & 240W Slim Line Only) Fingersafe, Spring-up Screw Terminals Barriers File #E234997 Top View Provides cooling for the power supply and prevents small objects from falling into the power supply circuitry. Terminals are captive spring-up screws, which makes using them as easy as pushing a screw down and tightening it. They are shock and vibration resistant, and work with ring lugs, fork connectors or stripped wire connections. The terminals are rated IP20 (when tightened) meaning they are recessed to keep fingers and objects from touching the input contacts. 182 Ventilation Grill www.IDEC.com 1706131649 Power Supplies PS5R Slim Line Series Output Capacity Style 10 5V DC 2.0A PS5R-SB05 12V DC 1.2A PS5R-SB12 24V DC 0.65A PS5R-SB24 12V DC 2.5A PS5R-SC12 24V DC 1.3A PS5R-SC24 24V DC 2.5A PS5R-SD24 Input Voltage 90 OI Touchscreens Part Numbers Output Voltage Rated Current Part Number 24V DC 3.75A PS5R-SE24 24V DC 5A PS5R-SF24 24V DC 10A PS5R-SG24 15 120 Panel Mounting Bracket for PS5R-SB (flat side mounting) PS9Z-5R2B Panel Mounting Bracket for PS5R-SC and PS5R-SD PS9Z-5R1C Panel Mounting Bracket for PS5R-SE PS9Z-5R1E Panel Mounting Bracket for PS5R-SF & PS5R-SG PS9Z-5R1G DIN rail (1000mm) BNDN1000 DIN rail end clip BNL5 800-262-IDEC (4332) * USA & Canada Barriers PS9Z-5R1B Communication 1706131649 Panel Mounting Bracket for PS5R-SB Sensors Accessories Power Supplies 240 85 to 264V AC Automation Software 60 PLCs 30 85 to 264V AC 183 Power Supplies OI Touchscreens PS5R Slim Line Series Specifications Model 5V DC output PS5R-SB05 - - - - - 12V DC output PS5R-SB12 PS5R-SC12 - - - - 24V DC output PS5R-SB24 PS5R-SC24 PS5R-SD24 PS5R-SE24 PS5R-SF24 PS5R-SG24 15W (5V Model is 10W) 30W 60W 90W 120W 240W Output Capacity Input Voltage (single-phase, 2-wire) 100VAC 0.45A 0.9A 200VAC 0.3A 0.6A Internal Fuse Rating Input PLCs Input Current (maximum) 2A Typical Efficiency Output Current Ratings 2.3A 1.0A 1.4A 1.7A 6.3A 0.75mA maximum 1mA maximum 69% - - - - - 75% 78% - - - - 24V DC 79% 80% 83% 82% 5V DC 2.0A - - - - 12V DC 1.2A 2.5A - - - - 24V DC 0.65A 1.3A 2.5A 3.75A 5A 10A 650ms maximum 500ms maximum - - - 100ms maximum (at rated input and output) Line Regulation 200ms maximum 0.4% maximum Load Regulation 1.5% maximum Temperature Regulation 0.8% max 0.05% degree C maximum Ripple Voltage 2% peak to peak maximum (including noise) 105% or more, auto reset 1% peak to peak maximum (including noise) 105 to 130%, auto reset LED (green) LED (amber) - - - LED (amber) Between Input and Ground: 2000 V AC, 1 minute Between input and output: 3000V AC, 1 minute; Between output and ground: 500V AC, 1 minute. Dielectric Strength Insulation Resistance Between Input & Output Terminals: 100 M Min -10 to +65C (14 to 149F) -10 to 60C (14 to 140F) Storage Temperature -25 to 75C (-13 to +167F) Operating Humidity 20 to 90% relative humidity (no condensation) Vibration Resistance Frequency 10 to 55Hz, Amplitude 0.375mm Shock Resistance Approvals 300m/s2 (30G) 3 times each in 6 axes EMC: EN61204-3 (EMI: Class B, EMS: Industrial), c-UL (CSA 22.2 No. 14), ANSI/ISA-12.12.01-2011, UL508, LVD: EN60950, EN50178 UL1310 Class 2, c-UL (CSA 22.2 No. 213 and 223) Harmonic Directive Weight (approx.) 160g SEMI F47 EN61000-3-2 A14 class A 250g 285g 440g 630g 1000g M3.5 slotted-Phillips head screw (screw terminal type) IP protection Dimensions H x W x D (inches) - N/A Terminal Screw Dimensions H x W x D (mm) 103 to 110%, auto reset 120% min. SHUTDOWN Operation Indicator Operating Temperature - 20ms minimum (at rated input and output) 200ms maximum Rise Time Voltage Low Indication 84% 10% (V. ADJ control on front) Overvoltage Protection Sensors 1.0A 4A 12V DC Overcurrent Protection Communication 3.5A 5V DC Starting Time Barriers 1.8A 50A maximum (at 200V AC) 132V AC: 0.38 mA maximum 264V AC: 0.75 mA maximum Voltage Adjustment Output 1.7A 3.15A Output Holding Time Power Supplies 85 to 264V AC, 100 to 350V DC Inrush Current (cold start) Leakage Current (at no load) Automation Software 85 to 264V AC, 100 to 370V DC IP20 fingersafe 90 x 22.5 x 95 95 x 36 x 108 115 x 46 x 121 115 x 50 x 129 125 x 80 x 149.5 3.54 x 0.89 x 3.74 3.74 x 1.42 x 4.25 4.53 x 1.81 x 4.76 4.53 x 1.97 x 5.08 4.92 x 3.15 x 5.89 1. For dimensions, see page 186. 184 www.IDEC.com 1706131649 Power Supplies PS5R Slim Line Series All IDEC Slim Line power supplies are listed to UL508, which allows operation at 100% capacity inside a panel. This eliminates the need to use oversize power supplies or utilize two power supplies derated at 50% of their rated output. Mounting B (upright) PS5R-SC Mounting B, C, D 0 10 20 30 40 Mounting C (left side up) 50 55 60 65 70 Mounting D (right side up) Operating Temperature (C) Dearting curve for PS5R-SB varies depending on mounting method (see right). 0 10 20 30 40 50 55 60 Operating Temperature (C) 70 0 10 20 30 40 45 50 Operating Temperature (C) 60 70 PS5R-SE 90W/3.75A/24V DC versus a Leading Competitor Standard derating curve (operating temperature vs. output current) Don't Believe the Hype Output Cuurent (%) 4.0 Currrent (A) "Boost" Rating 3.75A 0 10 20 30 40 50 Operating Temperature (C) 60 Other companies use slick marketing to sell you 60W power supplies with a "BOOST," but what they don't tell you is that these are merely 90W power supplies that have been renamed to fool you into thinking they have a unique feature. IDEC 90W power supplies are just what they claim, 90W power supplies. The truth is IDEC led the market by incorporating UL508 DIN rail mount power supplies as a standard product. Don't let the other guys pull a fast one on you by claiming to provide features that just aren't true, or even possible. See what IDEC has to offer, no strings attached. 3.0 "Normal" Rating 2.5A 2.0 70 1.0 Leading Competitor "24V/2.5A" Power Supplies 100 90 80 70 60 50 40 30 20 10 0 -10 100 90 80 70 60 50 40 30 20 10 0 -10 Automation Software PS5R-SD, -SE, -SF 100 90 80 70 60 50 40 30 20 10 0 -10 PS5R-SG Output Cuurent (%) Mounting A (standard) Output Cuurent (%) 100 90 80 70 60 50 40 30 20 10 0 -10 Mounting A PLCs Output Current (%) PS5R-SB The charts below show that the PS5R Slim 10W (at 60C) and 15W (at 60C), 30W/60W/90W (at 55C), 120W (at 40C), and 240W (at 45C) meet the elevated, operating temperature required by UL508 and EN60950 standards to operate at an output current of 100%. The output current starts to derate beyond the required temperature. OI Touchscreens Temperature Derating Curves Overload Protection Overload protection prevents the power supply from being damaged when an overload occurs. There are two kinds of protection. When the output voltage of the power supply rises to 120% or more of the rated value, the output will shut off. To restore power, only manual reset is available which is an advantage in troubleshooting. Overvoltage Protection Communication Overcurrent Protection PS5R-SF, -SG Overvoltage Protection When the output current exceeds 105% of the rated current, overload protection is triggered, and the output voltage starts decreasing. When the output current returns within the rated range, the overload protection function is automatically cleared. Sensors 24 Overcurrent Protection SEMI-F47 Approved The SEMI F47 (Semiconductor Processing Equipment Voltage Sag Immunity) defines the minimum voltage sag ride-through requirements for semiconductor processing, automated test equipment and other equipment. It requires that the equipment be able to tolerate voltage sags on an AC power line without interrupting operations. This avoids the loss of production and money. The graph shows how the equipment must tolerate sags to 50% for 200ms, sags to 70% for up to 0.5 seconds and sags to 80% for up to 1 second. Barriers Voltage Sag Sliding Scale PS5R-SF, -SG 1706131649 800-262-IDEC (4332) * USA & Canada 185 Power Supplies OI Touchscreens PS5R Slim Line Series Dimensions and Terminal Markings PS5R-SB Height Width Depth PS5R-SC PS5R-SD 90mm 22.5mm 95mm Height Width Depth INPUT 100-240VAC PS5R-SE 95.0mm 36.0mm 108.0mm LOW L N Height Width Depth INPUT 50/60Hz DC ON 115.0mm 46.0mm 121.0mm VR. ADJ ON L N INPUT 50/60Hz DC ON VR. ADJ VR. ADJ OUTPUT PLCs -V OUTPUT +V -V +V Automation Software OUTPUT PS5R-SF 115.0mm 50.0mm 129.0mm Height Width Depth 125.0 mm 80.0 mm 149.5 mm Sensors 149.5 125 Power Supplies Height Width Depth PS5R-SG Front Panel (terminals) Markings Name Description V. ADJ Voltage adjustment Adjusts within 10%; turn clockwise to increase output voltage. DC ON Operation indicator Green LED is lit when output voltage is on. DC Low Output indicator Amber LED is lit when output voltage drops below 80% of rated voltage. +V, -V DC output terminals +V: Positive output Terminal -V: Negative output terminal Frame ground Ground this terminal to reduce high-frequency noise caused by switching power supply. Input terminals Accept a wide range of voltages and frequencies (no polarity at DC input). Barriers Communication 80 L, N 186 www.IDEC.com 1706131649 Power Supplies PS5R Slim Line Series PS9Z-5R1B (for PS5R-SB) PS9Z-5R2B (for PS5R-SB) PS9Z-5R1B OI Touchscreens Mounting Bracket Dimensions (mm) PS9Z-5R1C (for PS5R-SC & PS5R-SD) 120 112 44 115 105 62.9 PS9Z-5R2B 102 110 PLCs 2-M4 tapped holes or 2-o4.5 through holes (See the front page for mounting examples.) 26 38 12 24.7 2-M4 Tapped Holes or 2-o4.5 Drilled Holes 2-M4 tapped holes or 2-o4.5 through holes PS9Z-5R1G (for PS5R-SF & PS5R-SG) Automation Software 135 145 135 125 PS9Z-5R1E (for PS5R-SE) Power Supplies 36 48 2-M4 Tapped Holes or 2-o4.5 Drilled Holes 36 48 4-M4 Tapped Holes or 4-o4.5 Drilled Holes Sensors Communication Barriers 1706131649 800-262-IDEC (4332) * USA & Canada 187 Power Supplies Automation Software PLCs OI Touchscreens PS5R Standard Series PS5R Standard Series Switching Power Supplies Key features: * Wide power range: 7.5W-480W * Universal input : 7.5W-50W: 85-264V AC/105-370V DC 100W: 85-132V AC/170-264V AC 240-370V DC (selectable) 75W, 120W, 240W: 85-264V AC/110-350V DC 480W: 3 phase: 320- 575V AC 3 phase: 360- 575V AC * Overcurrent/overvoltage protection * Power Factor Correction (75W, 120W, 240W models) EN61000-3-3 EN61000-3-2 * Voltage adjustment +10% * Spring-up crew terminal, IP20 (finger-safe) * DIN rail or panel surface mount * Approvals: CE marked EMC Directives: UL 508 Listed EN50081-2 c-UL EN50082-2 TUV approved EN61000-6-2 LVD EN60950:2000 UL 508 Listed File #E177168 Cert No. BL980213332392 Power Supplies Part Numbers 7.5 Sensors 15 85 to 264V AC 5V DC 1.5A PS5R-A05 12V DC 0.6A PS5R-A12 24V DC 0.3A PS5R-A24 5V DC 2.5A PS5R-B05 12V DC 1.2A PS5R-B12 24V DC 0.6A PS5R-B24 12V DC 2.5A PS5R-C12 24V DC 1.3A PS5R-C24 24V DC 2.1A PS5R-D24 Style Communication 75 Input Voltage 85 to 264V AC 100 30 50 Output Capacity 120 100 to 240V AC 240 Barriers 480 188 www.IDEC.com 320 to 575V AC (3 phase) 360 to 575V AC (2 phase) Output Voltage Rated Current Part Number 24V DC 3.1A PS5R-Q24 24V DC 4.2A PS5R-E24 24V DC 5A PS5R-F24 24V DC 10A PS5R-G24 24V DC 20A PS5R-TJ24* 1706131649 Power Supplies PS5R Standard Series Specifications Output Capacity Input Voltage (singlephase, 2-wire) PS5R-B05* PS5R-B12 PS5R-B24 15W -- PS5R-C12 PS5R-C24 30W Inrush Current 50A maximum (at cold start at 200V AC) 0.3A at 100V AC 2A 0.68A at 100V AC 3.15A Leakage Current (at no load) Output 1.1A at 100V AC 3.15A 70A maximum (at cold start at 230V AC) PS5R-F24 120W 100 to 240V AC, 50/60Hz, 110 to 340V DC 1.8A at 100V AC 4A 4A at 100V AC 79% at 24V 83% at 24V PS5R-TJ24 480W 3 phase: 320 to 575V AC 2 phase: 360 to 575V AC 3 x 1.1A 3 x 0.8A 6.3A 70A maximum (at cold start at 230V AC) 21A na <3.5ml 85% at 24V 83% at 24V 91% Automation Software 75% at 12V 75% at 24V Overvoltage Protection Outputs turns off at 105% (typical) 5V, 1.5A 12V, 0.6A 24V, 0.3A 5V, 2.5A 12V, 1.2A 24V, 0.6A 12V, 2.5A 24V, 1.3A Voltage Adjustments Output Holding Time Rise Time Line Regulation Load Regulation Fluctuation due to Ambient Temperature Change Ripple Voltage 24V, 2.1A 24V, 3.1A 24V, 4.2A 24V, 5A 24V, 10A 10% (V.ADJ screw on top) 20ms minimum (at full rated input and output) 200ms maximum (at full rated input and output) 0.4% maximum 1.5% maximum 150ms max. 24V, 20A 10ms typical ? 1.0% max 2.0% max 0.05% maximum 2% peak to peak maximum (including noise) 120% typical (Zener-limiting) PS5R-A PS5R-B No Dielectric Strength Insulation Resistance LED (green) PS5R-Q PS5R-E Yes No Between input and output terminals: 3,000V AC, 1 minute Between input terminals and housing: 2,000V AC, 1 minute Between output terminal and housing: 500V AC, 1 minute PS5R-D PS5R-F PS5R-G Yes Yes 2kV AC, 500V DG Between input and output terminals/input terminals and housing: 100M minimum (500V DC megger) -10 to +60C (14 to 140F) (see derating curves) -30 to +85C (-22 to 185F) Operating Humidity -25 to +70 C -40 to +85 C 95% max (at 25 C, no condensation) <15Hz amplitude +/- 2.5mm in accordance with IEC 60068-2-6 15 to 150Hz, 2.3g, 90 min. 30g in all directions in accordance with IEC 60068-2-27 20 to 90% relative humidity (no condensation) 45m/s2, 10 to 55Hz, 2 hours on each of 3 axes 300m/s2 (30G), 3 shocks in each of 6 directions Conforms to EMC Directives EN50081-2 & EN50082-2. LVD Directive EN60529 -- Certified to EN60950. UL508 listed. c-UL, TUV approved. CE marked. EN61000-3-2 Weight 150g 170g 360g 390g 800g 600g 1200g Termination Spring-up, fingersafe terminals with captive M3.5 screws IP protection IP20 (finger safe) Dimensions H x W x D (mm) 75 x 45 x 70 75 x 45 x95 75 x 90 x 95 75 x 90 x 95 120 x 85 x 140 75 x 145 x 95 120 x 115 x140 2.95 x 3.54 x 2.95 x 3.54 4.72 x 3.35 x 4.72 x 4.53 x Dimensions H x W x D (inches) 2.95 x 1.77 x 2.76 2.95 x 1.77 x 3.74 2.95 x 5.71 x 3.74 3.74 x 3.74 5.52 5.52 Communication Shock Resistance 10 to 50Hz, 0.75mm p-p, 2 hrs on each of 3 axes Sensors Operating Temperature Storage Temperature Vibration Resistance < 10mVpp 125% typical, auto reset 120% typical, auto reset PS5R-C Power Supplies Operation Indicator Parallel Operation Allowed 1.15A at 100V AC 3.15A -- -- PS5R-G24 240W 0.75mA maximum (60Hz, measured in conformance with UL, CSA, VDE) 69% at 5V 75% at 12V 79% at 24V Typical Efficiency Overload Protection PS5R-Q24 75W -- -- PS5R-E24 100W 100 to 120V AC, 50/60Hz 200 to 240V AC, 50/60Hz (jumper selectable) 240 to 370V DC 2.5A at 100V AC 1.5A at 200V AC 4A 50A maximum (at cold start at 200V AC) PLCs Internal Fuse Rating Voltage and Current Ratings -- -- PS5R-D24 50W 100 to 240V AC nominal (85 to 264V AC), 50/60Hz (47 to 63Hz) 110 to 340V DC nominal (105 to 370V DC) 0.17A at 100V AC 2A Input Current (typical) Input PS5R-A05 PS5R-A12 PS5R-A24 7.5W OI Touchscreens Model Approvals 1706131649 120 x 200x 140 4.72 x 7.87 x 5.51 2000g 130 x 115 x 152.5 5.12 x 4.53 x 6.00 Barriers 1. For dimensions, see page 192. 2. For usage instructions, see page 191. 2000g 3. *12.5W for 5VDC model. 800-262-IDEC (4332) * USA & Canada 189 Power Supplies Temperature Derating Curves PS5R-A/B PS5R-C/D Mounting style B 70 70 Output Current (%) 80 80 60 50 40 30 60 50 40 30 20 20 10 10 0 10 20 30 40 50 Mounting style A 90 Mounting style A 90 0 -10 Mounting style B 100 100 Output Current (%) PLCs OI Touchscreens PS5R Standard Series 0 -10 60 0 Mounting style A Output Current (%) 60 50 40 30 20 Mounting style B 70 60 50 40 30 10 0 10 20 30 40 50 0 60 0 Operating Temperature (C) Sensors PS5R-F/G Mounting Style B Mounting Style A 20 30 40 50 60 PS5R-TJ 100 100 90 90 80 Output Current (A) 70 Output Current (%) 10 Operating Temperature (C) 80 Communication Mouting style A 20 10 60 50 40 30 20 70 60 50 Iw 40 30 20 10 10 0 10 20 30 35 40 50 0 60 Operating Temperature (C) A Mounting (standard) Barriers 60 80 70 0 10 20 30 40 50 60 70 Ambient Temperature (C) B Mounting (Facing Upward) Vertical 190 50 90 80 0 30 35 40 100 90 0 -10 20 PS5R-Q Mounting style B 100 Output Current (%) Power Supplies Automation Software Operating Temperature (C) PS5R-E 10 Operating Temperature (C) Vertical www.IDEC.com 1706131649 Power Supplies Overcurrent Protection Characteristics PS5R-A/B Part Numbers: PS5R Accessories Description Part Number DIN rail (1000mm) BNDN1000 50 BNL5 0 Output Current (%) PLCs DIN rail end clip 100 Output Voltage (%) Appearance OI Touchscreens Accessories PS5R Standard Series 100 105 PS5R-C/D/E Installation Instructions 100 Automation Software The innovative terminals on the PS5R series use a spring-loaded screw. This makes installation as easy as pushing down and turning with a screwdriver. Installation time is cut in half since the screws do not need to be backed out to install wiring. The screws are held captive once installed and are 100% finger-safe. Screw terminals accept bare wire or ring or fork connectors. Output Voltage (%) Time-Saving Spring-up Terminals 50 1. Insert the wire connector into the slot on the side of the power supply. 0 Output Current (%) 100 105 Power Supplies Parallel Operation 2. Using a flat head or Phillips screwdriver, push down and turn the screw. PS5R Front Panel (terminals) Adjusts within 10%; turn clockwise to increase output voltage DC ON Operation indicator Green LED is lit when output voltage is on +V, -V DC output terminals +V: Positive output Terminal -V: Negative output terminal Frame ground Ground this terminal to reduce high-frequency currents caused by switching L, N Input terminals Accept a wide range of voltages and frequencies (no polarity at DC input) NC No connection Do not insert wires here, as this may damage the power supply + - PS5R PS5R PS5R Communication Voltage adjustment Sensors V. ADJ TERMINALS The wire is now connected, and the screw terminal is fingersafe! ELECTRICAL LOAD PS5R 1. Parallel operation only recommended for PS5R-Q24, PS5R-F24 and PS5R-G24. 2. Factory recommended diode ST Microelectronics BYV54V-50, BYV54V-100, BYV54V-200, BYV541V-200 or with equivalent electrical specifications. 3. Using the voltage adjustment make sure out-voltage is the same for all power supplies. Barriers 1706131649 800-262-IDEC (4332) * USA & Canada 191 Power Supplies Dimensions PS5R-B (15W) 13 90 80 13 13 60 75 DC ON DC ON V.ADJ V.ADJ 13 75 62.5 60 75 62.5 60 .5 6.5 -o 4-o4 M3.5 Terminal Screws DC ON PS5R-C (30W) M3.5 Terminal Screws 7.35 PS5R-A (7.5W) 10 OI Touchscreens PS5R Standard Series M3.5 Terminal Screws PS5R-Q (75W) 13 13 13 M3.5 Terminal Screws 13 13 16 13 13 M3.5 Terminal Screws 101 110 120 101 110 120 13 13 DC ON 12 PS5R-F (120W) 60 75 13 13 90 80 7.35 6.5 .5 -o 4-o4 10 Automation Software PS5R-D (50W) 12 35 38.5 7.35 7.35 12 35 38.5 R2 .2 6-o 5 6.5 R2 .2 6-o 5 6.5 5 PLCs V.ADJ M3.5 Terminal Screws 12 4.5 5 Power Supplies V.ADJ .5 o4 4- 4-o 75 85 PS5R-E (100W) PS5R-G (240W) 145 135 PS5R-TJ24 M3.5 Terminal Screws 115 4.5 190 200 4-o .5 200-240V 4o4 5 12 M3.5 Terminal Screws 130 102 110 120 Sensors 75 60 14 -o 6.5 4.6 13 13 26 13 13 105 115 Communication Terminal Markings PS5R-A/B -V NC PS5R-C/D/Q/F/G +V PS5R-E NC -V -V +V DC ON DC ON DC ON Barriers V.ADJ L N NC 100w-OUTPUT V.ADJ V.ADJ INPUT +V INPUT L N INPUT L N VOLTAGE SELECT 200-240V 100-120V NC 200-240V 192 www.IDEC.com 1706131649 Power Supplies PS3X OI Touchscreens PS3X Series Key features: * * * * * * * Compact size Universal AC input voltage 5V, 12V and 24V DC outputs Available with mounting brackets for direct or DIN rail mounting Overcurrent/overvoltage protection EMC, EN55022 Class B compliant UL/c-UL recognized, TUV PLCs Part Numbers Power Supply Output Capacity 15W 25W Input Output Voltage Voltage Output Current PS3X-B05AFC PS3X-B12AFC PS3X-B24AFC 5V 12V 24V 3.0A 1.3A 0.63A PS3X-C05AFC PS3X-C12AFC PS3X-C24AFC 5V 12V 24V 5.0A 2.1A 1.1A PS3X-D12AFG PS3X-D24AFG 12V 24V 4.2A 2.2A 100 to 240V AC 75W DIN-rail Mounting Bracket (optional) Applicable Power Supply PS3X-B PS3X-C PS3X-D PS3X-Q PS3X-E 5V 12V 24V 12.0A 6.0A 3.2A 16.0A 8.5A 4.5A Appearance PS9Z-3N4B PS9Z-3E4C PS9Z-3E4D Length Material Weight (g) BNDN1000 1000mm Aluminum 200 End Clips Appearance Part Number Description BNL5 small DIN rail end clip BNL6 medium DIN rail end clip (the BNL6 has a higher profile than BNL5) Cover and Terminal Style C: w/Standard cover, Horizontal terminal block (PS3X-B/C models) G: w/Standard cover, Vertical terminal block (PS3X-D/Q/E models) 800-262-IDEC (4332) * USA & Canada Barriers Input Voltage AF: 100 to 240V AC Communication PS3X - B 05 AF C 1706131649 Part Number Part Number Part Number Configuration Output Capacity B: 15W C: 25W D: 50W Q: 75W E: 100W Output Voltage 05: 5V DC (15W, 25W, 75W, 100W) 12: 12V DC 24: 24V DC PS9Z-3N3E DIN Rail 5V 12V 24V PS3X-E05AFG PS3X-E12AFG PS3X-E24AFG Part Number PS9Z-3N3A PS9Z-3N3B PS9Z-3E3B Sensors 100W PS3X-Q05AFG PS3X-Q12AFG PS3X-Q24AFG Applicable Power Supply PS3X-B PS3X-C PS3X-D PS3X-Q PS3X-E Power Supplies 50W Part Number Automation Software Style L-shaped Mounting Bracket (optional) 193 Power Supplies Specifications [15W] PS3X-B05/B12/B24 Model Voltage Range (Note 1) PLCs Frequency Input Current Inrush Current (Ta = -25C, ACV cold start) Leakage Current at 115V AC Efficiency (Typ.) (230V AC at input/ rated output) 5V 12V 24V at 230V AC Rated Voltage/Current Automation Software Adjustable Voltage Range Output Holding Time Start Time Ripple (including noise) Input Fluctuation Overvoltage Fluctuation Temperature Fluctuation Regulation Dielectric Supplementary Strength Functions Sensors Power Supplies Output Rise Time -20 to -10C -10 to 0C PS3X-B, C: 0 to +50C PS3X-D, Q, E: 0 to +45C Communication [50W] PS3X-D12/D24 100 to 240V AC 85 to 264V AC/ 120 to 375V DC Overvoltage Protection Operating Temperature Operating Humidity Storage Temperature Storage Humidity Vibration Resistance Shock Resistance EMI EMS EMC Safety Standards Dimensions (H x W x D) (mm) Weight (approx.) Terminal Screw [100W] PS3X-E05/E12/E24 0.65A max. 30A max. 47 to 63 Hz 1.3A max. 30A max. 1.8A max. 30A max. 2.5A max. 35A max. 60A max. 50A max. 50A max. 50A max. 70A max. 0.5mA max. 77% 81% 82% 5V, 3A 12V, 1.3A 24V, 0.63A 1.5mA max. 77% 81% 84% 5V, 5A 12V, 2.1A 24V, 1.1A 0.5A max. 40A max. 1.5mA max. 1.5mA max. 1.5mA max. -- 77% 77% 81% 82% 81% 84% 84% 84% -- 5V, 12A 5V, 16A 12V, 4.2A 12V, 6A 12V, 8.5A 24V, 2.2A 24V, 3.2A 24V, 4.5A 10% 13 ms typ. (100V AC) 10 ms typ. (100V AC) 23 ms typ. (100V AC) 14 ms typ. (100V AC) 17 ms typ. (100V AC) 60 ms minimum 60 ms minimum 60 ms minimum 60 ms minimum 80 ms minimum (230V AC) (230V AC) (230V AC) (230V AC) (230V AC) 1000 ms max. (230V AC input, rated output) 50 ms max. 30 ms max. 30 ms max. 30 ms max. 30 ms max. (230V AC input, rated (230V AC input, rated (230V AC input, rated (230V AC input, rated (230V AC input, rated output) output) output) output) output) 0.5% max. 5V: 2% max. 12V, 24V: 1% max. 0.04% / C max. (-20 to +50C) 0.04% / C max. (-10 to +45C) 5V: 140mV max. 5V: 200mV max. 12V: 240mV max. - - - 12V/24V: 200mV max. 24V: 300mV max. 5V: 140mV max. 5V: 140mV max. 5V: 160mV max. 5V: 160mV max. 12V: 240mV max. 12V: 240mV max. 12V: 240mV max. 12V: 240mV max. 12V/24V: 200mV max. 24V: 300mV max. 24V: 300mV max. 24V: 300mV max. 24V: 300mV max. 5V: 70mV max. 5V: 70mV max. 5V: 100mV max. 5V: 100mV max. 12V: 120mV max. 12V: 120mV max. 12V: 120mV max. 12V: 120mV max. 12V/24V: 150mV max. 24V: 150mV max. 24V: 150mV max. 24V: 150mV max. 24V: 150mV max. 105% min. (auto reset) 2 Voltage limitation at 115% min. Operation Indicator Between input and output terminals Between input and ground terminals Between output and ground terminals [75W] PS3X-Q05/Q12/Q24 88 to 264V AC / 125 to 375V DC Overcurrent Protection Insulation Resistance Barriers [25W] PS3X-C05/C12/C24 Rated Input Voltage Input OI Touchscreens PS3X Intermittent operation or output off at 115% min. 3 green LED 3000V AC, 1 minute 2000V AC, 1 minute 500V DC, 1 minute 100M minimum, 500V DC megger (between input and output terminals, between input and ground terminals) -20 to +70C (no freezing, see output derating) -10 to +70C (no freezing, see output derating) 20 to 85% RH (no condensation) -40 to +85C (no freezing) 10 to 95% RH (no condensation) 10 to 55 Hz, 20m/s2 constant, 2 hours each in 3 axes 200m/s2, 1 shock each in 3 axes EN55022 Class B EN55024 IEC/EN60950-1, UL60950-1, CSA C22.2 No. 60950-1 50.8H x 28W x 62D 50.8H x 28.5W x 79D 82H x 35W x 99D 95H x 38W x 129D 95H x 38W x 159D 130g 180g 340g 500g 700g M3 M3.5 1. See "Output Current vs. Input Voltage" characteristics next page. Not subject to safety standards. When using DC input, connect a fuse to the input terminal for DC input protection. 2. Overload for 30 seconds or longer may damage the internal elements. 3. One minute after the output has been turned off, turn on the AC input again. 194 www.IDEC.com 1706131649 Power Supplies PS3X Operating Temperature vs. Output Current (Derating Curves) OI Touchscreens Characteristics Overcurrent Protection Characteristics Conditions: Natural air cooling (operating temperature is the temperature around the power supply) PS3X-D/Q/E PS3X 90 90 80 80 80 70 70 70 60 50 40 30 20 10 60 50 40 37.5 30 20 10 0 -30 -20 -10 0 10 20 30 40 50 60 60 50 40 30 20 10 0 0 70 100 Intermittent Operation 90 Output Voltage (%) 100 Output Current (%) 100 Output Current (%) 100 PLCs Output Current (%) PS3X-B/C -10 Operating Temperature (C) 0 10 20 30 40 50 60 -10 70 Operating Temperature (C) 0 0 10 20 30 40 50 0Operating Temperature (C) Output Current (%) 60 100 70 105 PS3X-D/Q/E 100 100 90 90 90 80 80 80 70 70 70 60 50 40 30 20 60 50 40 30 20 10 0 PS3X-B: 85 100 PS3X-C: 88 100 Input Voltage (VAC) 264 264 0 60 50 40 30 20 10 88 100 264 Input Voltage (VAC) 0 88 176 Input Voltage (VAC) Power Supplies 10 Output Current (%) 100 Output Current (%) Output Current (%) PS3X-B/C Automation Software Output Current vs. Input Voltage (TA = 25C) 132 264 Operating Temperature by Safety Standards Power Supplies Up UL/EN60950-1 Mounting A, B 50C PS3X-D12, -D24 PS3X-Q05, -Q12, -Q24 PS3X-E05, -E12, -E24 45C Mounting A (standard) Sensors PS3X-B05, -B12, -B24 PS3X-C05, -C12, -C24 Mounting B Note: Observe the derating curves when operating PS3X power supplies. Communication Barriers 1706131649 800-262-IDEC (4332) * USA & Canada 195 Power Supplies Dimensions 11.4 15.1 39.1 62.0 65.0 Output Voltage Adjustment 18.0 82.0 74.0 99.0 2-M3 (Depth 2.5 to 4.0 mm max.) 2-M3 (Depth 2.5 to 4.0 mm max.) 9.5 (Terminal Centers) 95.0 LED 38.0 159.0 3-M3 (Depth 2.5 to 4.0 mm max.) 10.0 10.5 19.0 18.0 38.0 118.0 18.0 22.0 Output Voltage Adjustment 77.0 19.5 2-M3 (Depth 2.5 to 4.0 mm max.) 7-M3.5 (Terminal Screw) 2-M3 (Depth 2.5 to 4.0 mm max.) 129.0 3-M3 (Depth 2.5 to 4.0 mm max.) 162.6 78.0 32.0 33.0 34.0 LED 5-M3 (Terminal Screw) Output Voltage 32.0 Adjustment 24.0 95.0 78.0 Terminal Cover 129.3 ) Power Supplies 5-M3 (Terminal Screw) PS3X-E 9.5 (Terminal Centers) Automation Software Terminal Cover LED 2-M3 (Depth 2.5 to 4.0 mm max.) 79.0 2-M3 (Depth 2.5 to 4.0 mm max.) PS3X-Q 25.4 LED 5-M3 (Terminal Screw) Output Voltage 11.0 Adjustment 14.5 Output Voltage Adjustment 2-M3 (Depth 2.5 to 4.0 mm max.) 28 PLCs 5-M3 (Terminal Screw) 2-M3 (Depth 2.5 to 4.0 mm max.) 28.5 25.25 LED 99.7 55.0 20.5 45.5 Terminal Cover 91.9 55.0 35.0 13.0 50.8 8.25 Terminal Cover 17.5 76.0 39.1 50.8 Terminal Cover PS3X-D 9.5 (Terminal Centers) PS3X-C 7.62 (Terminal Centers) PS3X-B 7.62 (Terminal Centers) OI Touchscreens PS3X Marking Name L, N AC Input Terminal Terminal Markings Sensors PS3X-B/C PS3X-D/Q PS3X-E L N L L N N -V -V +V +V V.ADJ LED V.ADJ LED +V, -V -V V.ADJ +V V.ADJ LED DC Output Terminals Output Voltage Adjustment Power status LED Barriers Communication Ground Terminal Description Accepts a wide range of voltage and frequency. Polarity does not matter when using DC input. Be sure to connect this terminal to a proper ground. Positive and negative output terminals Allows adjustment within 10%. Turning clockwise increases the output voltage. Illuminates (green) when input power is applied. 196 www.IDEC.com 1706131649 Power Supplies PS3X L-shaped Mounting Bracket 26 4-o3.5 holes 16.5 30.0 14.0 4-o3.5 holes 65.0 83.5 3.5 13.5 0.5 3.5 20.0 28.0 17.5 2-o 6.5 2.3 27.0 20.0 10.0 ho les 4.0 PLCs PS9Z-3E3B (for 50W) 22.0 4-o 3.5 ho les PS9Z-3N3E (for 75W/100W) 3-o3.5 holes 3-o4.5 holes 25.0 118.0 77.0 15.5 31.0 13.5 4-o3.5 holes 4-o4.5 holes 22.5 ho les 3.5 x 4.5 oblong hole 7.5 42.5 15.0 28.0 2.0 .5 10.0 18.0 7.0 o3 28.0 17.5 4.5 100.0 0.3 157.5 10.0 6.5 2.3 18.0 Automation Software 74.0 80.0 0.3 103.0 34.5 12.5 0.3 0.2 2.0 6.5 72.0 20.0 27.0 14 PS9Z-3N3B (for 25W) 41 39.1 OI Touchscreens PS9Z-3N3A (for 15W) 2-C2.0 10.0 DIN-rail Mounting Bracket H1 H3 35 PS9Z-3E4C H2 L3 PS9Z-3N4B L1 L2 PS9Z-3E4D L1 L2 L3 H1 PS3X-B 95 105.5 35 5.2 20.5 50.8 H2 113 Power Supplies Part Number Applicable Power Supply H3 PS3X-C 95 35 5.2 20.5 50.8 PS3X-D 136 117* 35 5.2 20.5 82 PS3X-Q 188 141* 39.5 5.2 19.7 95 PS3X-E 188 173* 39.5 5.2 19.7 95 * Note that L2 is shorter than L1. Sensors Communication Barriers 1706131649 800-262-IDEC (4332) * USA & Canada 197 Power Supplies Instructions Installation Notes 3. Use M3 screws for mounting. Choose screws that protrude 2.5 to 4mm from the surface of the switching power supply. Mounting A (standard) 4. Do not cover the openings of the switching power supply. Ensure proper heat dissipation by convection. Mounting B Overcurrent Protection Chassis Mounting Panel Mounting Screw Automation Software Power Supplies Sensors 6. When derating of the output does not work, provide forced air-cooling. Overvoltage Protection PS3X-B/C: Voltage limit and auto-recovery method. The switching power supplies operate normally when voltage returns to normal. Series Operation When connecting two switching power supplies in a series, insert a Schottky diode to each output. 7. Make sure to wire the ground terminal correctly. 8. For wiring, use wires with heat resistance of 60C or higher. Use copper wire. Parallel Operation Parallel operation is not possible. 9. Recommended tightening torque of terminal screws: 0.8 N*m Insulation/Dielectric Test When performing an insulation/dielectric test, short the input (between AC) and output (between + and -). Do not apply or interrupt the voltage suddenly, otherwise surge voltage may be generated and the power supply may be damaged. Safety Precautions cident or failure may occur. * Do not use switching power supplies with equipment where failure or inadvertent operation may harm anyone, such as medical, aerospace, railway, nuclear, etc. PS3X switching power supplies are designed for use in general electric equipment such as office, communication, measuring, and industrial electric devices. * Observe the temperature derating curves. Operating temperature refers to the temperature around the lower part of the switching power supply. Failure to observe the derating curves could result in an internal temperature rise and possible failure of the switching power supply. * Do not disassemble, repair, or modify the power supplies, otherwise electric shock, fire, or failure may occur. * The fuse inside the switching power supply is for AC input. When using with DC input, install an external fuse. * Do not install the switching power supply in places where someone will touch it when input voltage is applied. Do not touch the switching power supply while input voltage is applied and right after the power is turned off, because high temperature and high voltage may cause burns and electric shocks. * Do not set the V. ADJ control over the setting range, otherwise performance deterioration or failure may occur. * Do not short circuit the output terminals or output lead wires, otherwise fire or damage may occur. Communication The output voltage drops automatically when an overcurrent flows, resulting in intermittent operation. Normal voltage is automatically restored when the load returns to normal conditions. However, overcurrent for a prolonged period of time or short-circuit causes the internal elements to deteriorate or break down. PS3X-D/Q/E: The output is turned off when an overvoltage is applied. When the output voltage has dropped due to an overvoltage, turn the input off, and after one minute, turn the input on again. 5. Maintain a minimum of 20mm clearance around the power supply. * Provide the final product with protection against failure or damage that may be caused by malfunction of the switching power supply. Damaged switching power supply may cause overvoltage on the output terminals, or may cause voltage drop. * Turn off power before wiring. Also, make sure to wire correctly. Improper wiring may cause electric fire or damage. * Do not use switching power supplies to charge rechargeable batteries. Barriers Adjustment of Output Voltage The output voltage can be adjusted within 10% of the rated output voltage by using the V.ADJ control. Turning the V.ADJ clockwise increases the output voltage. Turning counterclockwise decreases the output voltage. Note that overvoltage protection may work when increasing the output voltage. 1. When mounting the PS3X switching power supply, see the figure on the right. 2. See dimension drawings for mounting hole layouts. PLCs Up 2.5 to 4 mm OI Touchscreens PS3X * When failure or error occurs, shut down the input to the switching power supply, and contact IDEC. * Do not use or store the switching power supply in a place subject to extreme vibration or shocks, otherwise failure will result. * Do not use the switching power supply where it is subject to or near: * Direct sunlight, heat or high temperatures * Metal powder, oil, chemicals or hydrogen sulfide * Highly humid areas, such as a basement or conservatory * Inside freezers or refrigerators, near cooler exhaust, or other cold environments * Make sure that the input voltage does not exceed the rating. Note polarity of input and output terminals and wire correctly. Incorrect wiring may cause blown fuses (AC input power), smoke or fire. * Do not touch the inside of the switching power supply, and make sure that foreign objects do not enter the switching power supply, otherwise an ac- 198 www.IDEC.com 1706131649