OPT-1062A1G2D - Delta Electronics, Inc.

1x9 SC Duplex VCSEL 850nm Optical

Transceiver Module for 1.0625 GBd

Fibre Channel

OPT-1062A1 Series

Feature

Ts -40 85

T 260

t 10 sec.

Vcc 0 6 V

TA 0 70

Vcc 4.75 5.25 V

V - V -1.810 -1.475 V

V - V -1.165 -0.880 V

V 0.3 1.6 V

R50

Parameter Symbol Min. Typ. Max. Unit Reference

Storage Temperature

Lead Soldering Temperature

Lead Soldering Time

Supply Voltage

Parameter Symbol Min. Typ. Max. Unit Reference

Ambient Operating Temperature

Supply Voltage

Transmitter Data Input Voltage - Low

Transmitter Data Input Voltage - High

Transmitter Differential Input Voltage

Data Output Load

SOLD

IL CC

IH CC

Absolute Maximum Ratings

Recommended Operating Conditions

3, TUNG YUAN ROAD, CHUNGLI INDUSTRIAL ZONE, TAOYUAN SHIEN, TAIWAN, R.O.C.

TEL: 886-3-4526107 FAX: 886-3-4527314

DELTA ELECTRONICS, INC.

(CHUNGLI PLANT CPBU)

www.deltaca.com

1x9 SC Duplex VCSEL 850nm Optical

Transceiver Module for 1.0625 GBd

Fibre Channel

DC/DC (5V)

AC/DC (5V)

AC/AC TTL (5V)

AC/AC PECL (5V)

OPT-1062A1G1 A/B/C/D

OPT-1062A1G3 A/B/C/D

OPT-1062A3G2 A/B/C/D

OPT-1062A1G2 A/B/C/D

Compliant with Fibre Channel Standard

SC Duplex Multimode Transceiver

Industrial Standard 1x9 Footprint, Cost Effective Design

850 nm Vertical Cavity Surface Emitting Laser (VCSEL) Source Technology

Data Link up to 550 Meters in 50/125 MMF, 300 Meters in 62.5/125 MMF.

Single + 5V Power Supply. Available for PECL and TTL Logic Interface.

Class 1 FDA and IEC laser safety compliant (Laser Class 1 Product)

1x9 SC Duplex VCSEL 850nm Optical

Transceiver Module for 1.0625 GBd

Fibre Channel

3, TUNG YUAN ROAD, CHUNGLI INDUSTRIAL ZONE, TAOYUAN SHIEN, TAIWAN, R.O.C.

TEL: 886-3-4526107 FAX: 886-3-4527314

DELTA ELECTRONICS, INC.

(CHUNGLI PLANT CPBU)

www.deltaca.com

1x9 SC Duplex VCSEL 850nm Optical

Transceiver Module for 1.0625 GBd

Fibre Channel

Transmitter Electro - Optical Performance Specifications:

Note (1). With BER better than orequal to 1x10 , measured in the center of the eye opening with 2 -1 NRZ PRBS.

Note (2). These are 20%~80% values.

-12 23

Receiver Electro - Optical Performance Specifications:

Parameter Symbol Min. Typ. Max. Unit Reference

Supply current

Launched power (avg.)

Optical extinction ratio

Center wavelength

Spectral width

Optical risetime

Optical falltime

Relative Intensity Noise

Parameter Symbol Min. Typ. Max. Unit Reference

Supply current

Data output voltage - Low

Data output voltage - High

Optical input sensitivity (avg.)

Optical input saturation (avg.)

Optical wavelength

Output Data risetime

Output Data falltime

Signal detect - Assert

Signal detect - Deassert

Signal detect - Hysteresis

Icc 180 mA

P -10 -4 dBm

9dB

c 830 850 860 nm

0.85 nm rms

t 0.45 ns Note (1)

RIN -116 DB/Hz

Icc 130 mA

V - Vcc -1.950 -1.620 V

V - Vcc -1.045 -0.740 V

P -17 dBm Note (1)

P -3 dBm Note (1)

850 nm

t 0.4 ns Note (2)

P -18 dBm

P -30 dBm

P-P 1 dB

OL cc

SAT

Note (1). These are 20-80% values and include the effect of a fourth order filter.

OPT-1062A1 Series

1x9 SC Duplex VCSEL 850nm Optical

Transceiver Module for 1.0625 GBd

Fibre Channel

3, TUNG YUAN ROAD, CHUNGLI INDUSTRIAL ZONE, TAOYUAN SHIEN, TAIWAN, R.O.C.

TEL: 886-3-4526107 FAX: 886-3-4527314

DELTA ELECTRONICS, INC.

(CHUNGLI PLANT CPBU)

www.deltaca.com

1x9 SC Duplex VCSEL 850nm Optical

Transceiver Module for 1.0625 GBd

Fibre Channel

Recommended Circuit Schematic (For OPT-1062A1G1)

Multimode 850nm Gigabit Ethernet / Fiber Channel 1x9 Transceiver, DC/DC, 5V Transceiver Version

C1/2/3 = 4.7 uF

C4/5/6/7 = 10 nF

L1/2 = 1 uH

R1/2 = 68

R3/4 = 191

R7/8 = 270

R5/6/9/10/11/12 Depend on SerDes chip used and desired line termination (50 Strip line)

R13 = 510 When we want PECL output in SD pin we use R13=510.

Value of R5/6/9/10/11/12 may very as long as proper 50 termination to VEE ,it depend on

SerDes chip used and desired line termination.All the transceiver of Delta contains an automatic

shutdown circuit.Reset depends on the power OFF and then ON. For good EMI performance the

power supply filter is require.Use short tracks from the inductor L1/2 to the module VccTx/VccRx .

This recommend Circuit assume Gigabit Ethernet / Fiber Channel using 5V power supply and SerDes

Chip using 3.3/5Vpower supply.

Laser

Driver

LIMITING

Amplifier

Serializer/

Deserializer

Gigabit

Transceiver

Chip

ECL/PECL

DRIVER

Receiver

PLL etc.

VCC

TX+

TX-

RD-

RD+

VCC SerDes

5V / 3.3V

TXGND

TxD

VCCRx

Pre-

Amp

RxD

RxGND

VCCTx

Delta Transceiver

C1 L2

Signal detect SD to upper level

R13

R12

R10

R11

R4 R2

RD-

RD+

VCCSerDes

5V / 3V

OPT-1062A1 Series

3, TUNG YUAN ROAD, CHUNGLI INDUSTRIAL ZONE, TAOYUAN SHIEN, TAIWAN, R.O.C.

TEL: 886-3-4526107 FAX: 886-3-4527314

DELTA ELECTRONICS, INC.

(CHUNGLI PLANT CPBU)

www.deltaca.com

Recommended Circuit Schematic (For OPT-1062A1G3)

Multimode 850nm Gigabit Ethernet / Fiber Channel 1x9 Transceiver, AC/DC, 5V Transceiver Version

C1/2/3 = 4.7 uF

C4/5/6/7 = 10 nF

L1/2 = 1 uH

R7/8 = 270

R5/6/9/10/11/12 Depend on SerDes chip used and desired line termination (50 Strip line)

R13 = 510 When we want PECL output in SD pin we use R13=510.

Value of R5/6/9/10/11/12 may very as long as proper 50 termination to VEE ,it depend on

SerDes chip used and desired line termination.All the transceiver of Delta contains an automatic

shutdown circuit.Reset depends on the power OFF and then ON. For good EMI performance the

power supply filter is require.Use short tracks from the inductor L1/2 to the module VccTx/VccRx.

This recommend Circuit assume Gigabit Ethernet / Fiber Channel using 5V power supply and SerDes

Chip using 3.3/5Vpower supply.

Laser

Driver

LIMITING

Amplifier

VCC SerDes

5V / 3.3V

TXGND

TxD

VCCRx

Pre-

Amp

100R

RxD

RxGND

VCCTx

Delta Transceiver

C1 L2

Signal detect SD to upper level

R13

R12

R10

R11

RD-

RD+

VCCSerDes

5V / 3V

Serializer/

Deserializer

Gigabit

Transceiver

Chip

ECL/PECL

DRIVER

Receiver

PLL etc.

VCC

TX+

TX-

RD-

RD+

1x9 SC Duplex VCSEL 850nm Optical

Transceiver Module for 1.0625 GBd

Fibre Channel

1x9 SC Duplex VCSEL 850nm Optical

Transceiver Module for 1.0625 GBd

Fibre Channel

OPT-1062A1 Series

3, TUNG YUAN ROAD, CHUNGLI INDUSTRIAL ZONE, TAOYUAN SHIEN, TAIWAN, R.O.C.

TEL: 886-3-4526107 FAX: 886-3-4527314

DELTA ELECTRONICS, INC.

(CHUNGLI PLANT CPBU)

www.deltaca.com

Recommended Circuit Schematic (For OPT-1062A1G2 or OPT-1062A3G2)

Multimode 850nm Gigabit Ethernet / Fiber Channel 1x9 Transceiver, AC/AC, 5V Transceiver Version

C1/2/3 = 4.7 uF

L1/2 = 1 uH

R7/8 = 270

R5/6/9/10/11/12 Depend on SerDes chip used and desired line termination (50 Strip line)

R13 = 510

Value of R5/6/9/10/11/12 may very as long as proper 50 termination to VEE ,it depend on

SerDes chip used and desired line termination.All the transceiver of Delta contains an automatic

shutdown circuit.Reset depends on the power OFF and then ON. For good EMI performance the

power supply filter is require.Use short tracks from the inductor L1/2 to the module VccTx/VccRx.

This recommend Circuit assume Gigabit Ethernet / Fiber Channel using 5V power supply and SerDes

Chip using 3.3/5Vpower supply.

When we want PECL output in SD pin we use R13=510, and no connector

when we want TTL output.

Laser

Driver

LIMITING

Amplifier

VCC SerDes

5V / 3.3V

TXGND

TxD

VCCRx

Pre-

Amp

100R

RxD

RxGND

VCCTx

Delta Transceiver

C1 L2

Signal detect SD to upper level

R13

R12

R10

R11

VCCSerDes

5V / 3V

1x9 SC Duplex VCSEL 850nm Optical

Transceiver Module for 1.0625 GBd

Fibre Channel

1x9 SC Duplex VCSEL 850nm Optical

Transceiver Module for 1.0625 GBd

Fibre Channel

Serializer/

Deserializer

Gigabit

Transceiver

Chip

ECL/PECL

DRIVER

Receiver

PLL etc.

VCC

TX+

TX-

RD-

RD+

OPT-1062A1 Series

3, TUNG YUAN ROAD, CHUNGLI INDUSTRIAL ZONE, TAOYUAN SHIEN, TAIWAN, R.O.C.

TEL: 886-3-4526107 FAX: 886-3-4527314

DELTA ELECTRONICS, INC.

(CHUNGLI PLANT CPBU)

www.deltaca.com

1x9 SC Duplex VCSEL 850nm Optical

Transceiver Module for 1.0625 GBd

Fibre Channel

1x9 SC Duplex VCSEL 850nm Optical

Transceiver Module for 1.0625 GBd

Fibre Channel

MECHANICAL DIMENSIONS

Unit: mm

TYPE: A (Flush Shielding)

29.70 0.20

1.0

25.80 0.20

39.50 0.20

25.40 0.20

10.25 0.20

9.50 0.20 22 0.20

15.83

20.32

2.54

20.32

12.70 0.10

OPT-1062A1 Series

3, TUNG YUAN ROAD, CHUNGLI INDUSTRIAL ZONE, TAOYUAN SHIEN, TAIWAN, R.O.C.

TEL: 886-3-4526107 FAX: 886-3-4527314

DELTA ELECTRONICS, INC.

(CHUNGLI PLANT CPBU)

www.deltaca.com

1x9 SC Duplex VCSEL 850nm Optical

Transceiver Module for 1.0625 GBd

Fibre Channel

1x9 SC Duplex VCSEL 850nm Optical

Transceiver Module for 1.0625 GBd

Fibre Channel

MECHANICAL DIMENSIONS

Unit: mm

TYPE: B (Protruding Shielding)

29.60

39.50

25.40 0.20

2.02

3.80 0.10

0.50 max.

9.50 0.20

20.32

15.83 0.20

20.32

2.54

20.32

1.30

12.70 0.10

OPT-1062A1 Series

3, TUNG YUAN ROAD, CHUNGLI INDUSTRIAL ZONE, TAOYUAN SHIEN, TAIWAN, R.O.C.

TEL: 886-3-4526107 FAX: 886-3-4527314

DELTA ELECTRONICS, INC.

(CHUNGLI PLANT CPBU)

www.deltaca.com

1x9 SC Duplex VCSEL 850nm Optical

Transceiver Module for 1.0625 GBd

Fibre Channel

1x9 SC Duplex VCSEL 850nm Optical

Transceiver Module for 1.0625 GBd

Fibre Channel

MECHANICAL DIMENSIONS

Unit: mm

TYPE: C (Entirely Wrap-Up)

29.60

10.20 0.20

9.50 0.20

3.80 0.10

15.83 0.20

20.32

2.54

20.32

1.30

20.32

12.70 0.10

OPT-1062A1 Series

3, TUNG YUAN ROAD, CHUNGLI INDUSTRIAL ZONE, TAOYUAN SHIEN, TAIWAN, R.O.C.

TEL: 886-3-4526107 FAX: 886-3-4527314

DELTA ELECTRONICS, INC.

(CHUNGLI PLANT CPBU)

www.deltaca.com

1x9 SC Duplex VCSEL 850nm Optical

Transceiver Module for 1.0625 GBd

Fibre Channel

1x9 SC Duplex VCSEL 850nm Optical

Transceiver Module for 1.0625 GBd

Fibre Channel

MECHANICAL DIMENSIONS

Unit: mm

TYPE: D (Clamp Shielding)

27.47

25.40 0.20

3.80 0.10

0.50 max.

9.50 0.20

15.83 0.20

20.32

2.54

20.32

1.30

12.70 0.10

OPT-1062A1 Series