LV MFMTM Filter MFM1714x50M50C5yzz Low-Voltage MIL-COTS Input Filter Module Features & Benefits Product Description * 28V nominal input The MFM DCMTM Filter is a DC front-end module that provides EMI filtering and transient protection. The MFM DCM Filter enables designers using Vicor 28V nominal input voltage VIATM or ChiPTM[a] modules to meet conducted emission/conducted susceptibility per MIL-STD-461E/F; and input transients per MIL-STD-704A/F, MIL-STD-1275A/B/D/E and DO-160E. The MFM DCM Filter accepts an input voltage of 16 - 50VDC (28V nominal input ) and delivers output power up to 350W. * 99% efficiency * Reverse-polarity protection MIL-STD-1275E * EMI filtering MIL-STD-461E/F, selected CE and CS tests * Input transient protection MIL-STD-1275A/B/D/E MIL-STD-704A/F (MIL-HDBK-704-8) Normal and abnormal transients * Envronmental qualification MIL-STD-810 MIL-STD-202 * Low M-Grade temperature rating, providing operation down to -55C * Output power up to 350W * Available in chassis and PCB mount * Small size 1.76 x 1.40 x 0.36in [44.6 x 35.5 x 9.2mm] Size: 1.76 x 1.40 x 0.36in [44.6 x 35.5 x 9.2mm] Typical Applications * Defense * Aerospace Compatible Products [a] * Low input voltage DCM3414 VIATM Additional components are required for EMI filtering and transient suppression, when used with ChiPTM package modules. * Low input voltage ChiP[a] DCM Part Ordering Information Product Function Package Length Package Width Package Type Max High Side Voltage MFM 17 14 x 50 MFM = MIL-COTS Input Filter Module Length in Inches x 10 Width in Inches x 10 B = Board VIA V = Chassis VIA LV MFMTM Filter Page 1 of 16 High Max Side Low Voltage Side Range Voltage Ratio M 50 Internal Reference Rev 1.3 10/2018 Max Low Side Current Product Grade (Case Temperature) Option Field C5 y zz M = -55 to 100C 00 = Chassis 04 = Short Pin 08 = Long Pin MFM1714x50M50C5yzz Typical Application MFM F 16 - 50V Source +IN DCM3414 VIATM EMI GND CIN -IN +IN +OUT VDDE EN TR -SENSE +SENSE CIN-DCM -OUT -IN earth ground M-Grade DCM3414 VIA with an MFM input filter, to meet the EMI and transient requirements Parts List for Typical Applications F LV MFMTM Filter Page 2 of 16 EATON (Cooper/Bussman) ABC series, fast-acting tube fuses rated 30A Littlefuse NANO2 456 Series, surface-mount fuses rated 30A Rev 1.3 10/2018 +OUT -OUT COUT-EXT L O A D MFM1714x50M50C5yzz Pin Configuration +OUT +IN EMI GND -IN -OUT MFM1714 Filter - Chassis (Lug) Mount - Terminals Up -IN -OUT EMI GND +IN +OUT MFM1714 Filter - PCB Mount - Pins Down Note: These pin drawings are not to scale. Pin Descriptions Signal Name Type +IN INPUT POWER Positive input power terminal -IN INPUT POWER RETURN Negative input power terminal EMI GND EMI GROUND EMI ground terminal +OUT OUTPUT POWER Positive output power terminal -OUT OUTPUT POWER RETURN Negative output power terminal LV MFMTM Filter Page 3 of 16 Function Rev 1.3 10/2018 MFM1714x50M50C5yzz Absolute Maximum Ratings The absolute maximum ratings below are stress ratings only. Operation at or beyond these maximum ratings can cause permanent damage to the device. Electrical specifications do not apply when operating beyond rated operating conditions. Parameter Comments Continuous Input Voltage (+IN to -IN) Output Voltage (+OUT to -OUT) Min Max -50 65.0 Transient per MIL-STD-1275D/E, 50ms 100 Transient per MIL-STD-1275A/B/D, 70s 250 Transient per DO-160E, 100ms 80 Continuous -0.5 Dielectric Withstand (Input/Output to EMI GND/Case) Unit VDC 65.0 VDC 1500 VDC Storage Temperature M-Grade -65 125 C Internal Operating Temperature M-Grade -55 125 C 22 A 4 (0.45) in.lbs (N.m) Average Output Current Input/Output Pin Torque and Mounting Torque Electrical Specifications Specifications apply over all line and load conditions, unless otherwise noted; boldface specifications apply over the temperature range of -55C TCASE 100C (M-Grade); all other specifications are at TCASE = 25C unless otherwise noted. Attribute Symbol Conditions / Notes Min Typ Max 16 28 50 Unit Power Input / Output Specification Continuous operation Input Voltage Range[b] Maximum Output Rated Output Current[c] Power[c] Continuous reverse-voltage protection -50 Transient per MIL-STD-1275D/E, 50ms 100 Transient per MIL-STD-1275A/B/D, 70s 250 Transient per DO-160E, 100ms 80 IOUT_MAX Continuous at 16V (IOUT = 350/VIN) 22 A POUT Continuous, over all line conditions 350 W 0.65 VDC 98.2 % VIN Internal Voltage Drop Efficiency @16V, 22A, 100C case Full load, low line, high temperature 97.7 98 Full load, nominal line, high temperature 99.2 99.4 % Full load, high line, high temperature 99.7 99.8 % [b] Transient immunity specifications are met only when LV MFM is used with M-Grade 16 - 50VIN DCM3414 VIATM. [c] One MFM for each DCMTM even if the total power of the DCM is below P OUT maximum value. LV MFMTM Filter Page 4 of 16 V Rev 1.3 10/2018 MFM1714x50M50C5yzz EMI/EMC Standard Test Procedure Notes MIL-STD-461E/F Conducted Emmisions Conducted Susceptibility CE101 Figure CE101-4, Navy ASW & Army Aircraft, Curve #2 (28VDC or below) CE102 Figure CE102-1, Basic curve for all applications CS101 Figure CS101, Curve #2, for all applications (28VDC or below) MIL-STD-1275 Transient Immunity[d] 100VDC for 50ms duration MIL-STD-1275A/B/D/E 250VDC for 70s MIL-STD-704 Transient Immunity[d] MIL-STD-704A (MIL-HDBK-704-8) Normal Voltage Transients From table LDC 105-II (A-J) overvoltage 70VDC for 20ms duration; within the MIL-STD-1275 (100V for 50ms) transient condition MIL-STD-704B/C/D/E/F (MIL-HDBK-704-8) Normal Voltage Transients From table LDC 105-III (AA-RR) overvoltage 50VDC for 12.5ms duration, undervoltage 18VDC for 15ms duration; within the normal operating input voltage range MIL-STD-704A (MIL-HDBK-704-8) Abnormal Voltage Transients From table LDC 302-II (A-J) overvoltage 80VDC for 50ms duration; within the MIL-STD-1275 (100V for 50ms) transient condition MIL-STD-704E/F (MIL-HDBK-704-8) Abnormal Voltage Transients From Table LDC 302-IV (AAA-FFF), overvoltage test conditions; within the normal operating input voltage range DO-160E Transient Immunity[d] [d] DO-160E sec. 16, cat. z 80VDC for 100ms Transient immunity specifications are met only when LV MFM is used with M-grade 16 - 50VIN DCM3414 VIATM. LV MFMTM Filter Page 5 of 16 Rev 1.3 10/2018 MFM1714x50M50C5yzz Typical Characteristics 0 -10 -20 Attenuation (dB) F/Hz 100k 1M Cursor 1 Cursor 2 CM-Mode -33.201dB -68.687dB DF-Mode -38.75dB -61.283dB -30 -40 -50 -60 -70 -80 -90 100 1k 10k 100k 1M 10M Frequency (Hz) Common Mode Differential Mode Figure 1 -- Attenuation (dB) vs. frequency (Hz), input leads are terminated with LISN impedances 25 for common mode, 100 for differential mode 40 350 300 20 250 200 0 150 -20 100 50 -40 100 1k 10k 100k 1M 10M Frequency (Hz) Output Impedance Z (dB) Output Impedance Z () Figure 2 -- Output impedance vs. frequency (Hz) plot looking back into the output terminals of the MFM with shorted input terminals LV MFMTM Filter Page 6 of 16 Rev 1.3 10/2018 0 Output Impedance Mangitude Z () Output Impedance Mangitude Z (dB): 400 MFM1714x50M50C5yzz Typical Conducted Emissions CE101 peak scans with MFM1714V50M50C5M00 and DCM3414V50M31C2T01, in either condition: -OUT connected to GND or -OUT floating. 50 Termination on Signal Output Port (One for Each LISN) DCM3414 VIATM DC + Power Supply - LISN Screen Room/ Filters +IN CIN +OUT +IN +OUT -IN -OUT LV MFM -IN LISN COUT -OUT Load EMI GND Current Probe EMI Receiver Figure 3 -- A typical test set up for conducted emissions CE101 is shown above. A current probe is used to measure and plot the variations in the current through the RED and BLACK leads at various load conditions. Det Att 10 dB ResBW INPUT 2 140 Meas T 100 Hz MA Trd 100 Hz 20 ms Unit 1 kHz CE101 100 Hz Det ResBW Meas T 1 kHz MA Trd 10 Hz 20 ms Unit 1 [T1] 130 SGL 120 CE101 dB A 10 dB kHzA 84.68 338.00000000 Hz SGL 120 110 110 1MA 100 CE101-42 1MA 100 CE101-42 90 90 80 80 70 70 60 60 50 50 40 40 30 30 20 20 10 1 10 23.Nov 2016 14:25 30 Hz Date: 0 10 kHz 23.NOV.2016 14:25:39 Det Att 10 dB ResBW INPUT 2 140 Meas T 100 Hz 23.Nov 2016 14:40 30 Hz Date: Figure 4 -- Peak scan for the RED lead with CIN = 2200F, COUT-EXT = 1000F, 0% load 1 kHz MA Trd 100 Hz 20 ms Unit 10 kHz 23.NOV.2016 14:40:36 Figure 5 -- Peak scan for the RED lead with CIN = 2200F, COUT-EXT = 1000F, 100% load CE101 Att 10 dB dB A Marker 1 [T1] INPUT 2 140 10 kHz 130 86.36 dB A 318.00000000 Hz 100 Hz Det ResBW Meas T 1 kHz 130 SGL 120 MA Trd 100 Hz 20 ms Unit 1 [T1] CE101 dB A 10 dB kHzA 86.36 318.00000000 Hz SGL 120 110 110 1MA 100 CE101-42 1MA 100 CE101-42 90 90 80 80 70 70 60 60 50 50 40 40 30 30 20 20 10 0 84.68 dB A 338.00000000 Hz INPUT 2 140 10 kHz 130 0 Marker 1 [T1] Att 10 dB dB A 1 10 23.Nov 2016 14:21 30 Hz Date: 0 10 kHz 23.NOV.2016 14:21:38 Figure 6 -- Peak scan for the BLACK lead with CIN = 2200F, COUT-EXT = 1000F, 0% load LV MFMTM Filter Page 7 of 16 23.Nov 2016 14:06 30 Hz Date: 10 kHz 23.NOV.2016 14:06:27 Figure 7 -- Peak scan for the BLACK lead with CIN = 2200F, COUT-EXT = 1000F, 100% load Rev 1.3 10/2018 MFM1714x50M50C5yzz Typical Conducted Emissions (Cont.) CE102 peak scans with MFM1714V50M50C5M00 and DCM3414V50M31C2T01, in either condition: -OUT connected to GND or -OUT floating. 50 Termination DCM3414 VIATM DC + Power Supply - LISN Screen Room/ Filters +IN CIN LISN +OUT +OUT -IN -OUT COUT CIN-DCM LV MFM -IN +IN -OUT Load EMI GND 20dB Attenuator EMI Reciever Figure 8 -- A typical test set up for conducted emissions CE102 is shown above. A 50 termination is used for LISN and voltage across the RED and BLACK leads are measured at various load conditions. Marker 1 [T1] Att 10 dB 67.96 dB V 40.40000000 kHz INPUT 2 110 Det ResBW Meas T 100 kHz MA Trd 10 kHz 20 ms Unit 1 MHz 1 [T1] 100 CE102RED Marker 1 [T1] Att 10 dB dB V 110 10 dB MHzV 67.96 40.40000000 kHz 73.00 dB V 40.40000000 kHz INPUT 2 Det ResBW Meas T 100 kHz MA Trd 10 kHz 20 ms Unit 1 MHz 1 [T1] 100 SGL 90 CE10228 CE102RED dB V 10 dB MHzV 73.00 40.40000000 kHz SGL 90 CE10228 1MA 80 1MA 80 1 1 70 70 60 60 50 50 40 40 30 30 20 10 20 30.Nov 2016 15:24 10 kHz Date: 10 10 MHz 30.NOV.2016 15:24:45 Date: Figure 9-- Peak scan for the RED lead with CIN = 2200F, CIN-DCM = 1000F, COUT-EXT = 1000F, 0% load Att 10 dB Marker 1 [T1] INPUT 2 110 68.19 dB V 40.40000000 kHz 100 kHz 100 30.Nov 2016 15:19 10 kHz Det ResBW Meas T MA Trd 10 kHz 20 ms Unit 1 MHz 1 [T1] 10 MHz 30.NOV.2016 15:19:13 Figure 10 -- Peak scan for the RED lead with CIN = 2200F, CIN-DCM = 1000F, COUT-EXT = 1000F, 100% load CE102BLK Att 10 dB dB V 110 10 dB MHzV 68.19 40.40000000 kHz Marker 1 [T1] INPUT 2 72.98 dB V 40.40000000 kHz 100 kHz 100 SGL 90 CE10228 Det ResBW Meas T MA Trd 10 kHz 20 ms Unit 1 MHz 1 [T1] CE102BLK dB V 10 dB MHzV 72.98 40.40000000 kHz SGL 90 CE10228 1MA 80 1MA 80 1 1 70 70 60 60 50 50 40 40 30 30 20 10 20 30.Nov 2016 15:26 10 kHz Date: 10 10 MHz 30.NOV.2016 15:26:59 Figure 11 -- Peak scan for the BLACK lead with CIN = 2200F, CIN-DCM = 1000F, COUT-EXT = 1000F, 0% load LV MFMTM Filter Page 8 of 16 30.Nov 2016 15:32 10 kHz Date: 10 MHz 30.NOV.2016 15:32:50 Figure 12 -- Peak scan for the BLACK lead with CIN = 2200F, CIN-DCM = 1000F, COUT-EXT = 1000F, 100% load Rev 1.3 10/2018 MFM1714x50M50C5yzz Electrical Power Characteristics Transient immunity with MFM1714V50M50C5M00 and DCM3414V50M13C2M01 per MIL-STD-1275D/E. CH1 CH2 +IN CIN -IN +IN +OUT 1st Stage EMI Filter EMI GND & Transient Suppression CIN-DCM -OUT CH4 VIN_ChiP DCM LV MFM Fuse 16 - 50V Source CH3 +IN_ChiP DCM +OUT 2nd Stage EMI Filter & Transient Suppression -IN COUT-EXT -IN_ChiP DCM -OUT DCM3414 VIA (16 - 50V Input, M-Grade) earth ground Note: Input line transients are clamped to maximum acceptable input voltage (VIN_ChiP DCM) using two stages of active transient suppression circuit. Example: A 100V, 50ms input line transient is clamped as follows: 1. LV MFM clamps 100V to 80V. 2. DCM3414 VIATM input transient circuit clamps 80V to VIN_ChiP DCM = VIN. (Please refer to the appropriate DCM3414 VIA data sheet for VIN.) Figure 13 -- Input line transient suppression block diagram Figure 14 -- Transient immunity; LV MFM and DCM3414 VIA output response to an 100V, 50ms input transient LV MFMTM Filter Page 9 of 16 Rev 1.3 10/2018 L O A D MFM1714x50M50C5yzz General Characteristics Specifications apply over all line and load conditions, TINT = 25C, unless otherwise noted; boldface specifications apply over the temperature range of the specified product grade. Attribute Symbol Conditions / Notes Min Typ Max Unit Mechanical Length L 44.6 [1.76] mm [in] Width W 35.5 [1.39] mm [in] Height H 9.22 [0.36] mm [in] Volume Vol 14.5 [0.88] cm3 [in3] Mass (Weight) M 30 [1.06] g [oz] Pin Material C145 copper, 1/2 hard Underplate Low-stress ductile Nickel 50 100 Palladium 0.8 6 Soft Gold 0.12 2 Pin Finish Flatness <0.25 [0.010] in in mm [in] Thermal Internal Operating Temperature M-Grade; See thermal considerations section Case Temperature -55 125 -55 100 C Thermal Resistance, Internal to Case Non-Pin Side INT_NON_PIN_SIDE 14 C/W Thermal Resistance, Internal to Output Terminals INT_OUT_TERMINALS 4.7 C/W Soldering Temperature See: AN:401 PCB Mount VIA Soldering Guidelines Reliability MTBF MIL-HDBK-217FN2 Parts Count - 25C Ground Benign, Stationary, Indoors / Computer 6.6 MHrs 1500 VDC Safety Dielectric Withstand Input / Output to EMI GND/Case Agency Approvals / Standards CE marked to the Low Voltage Directive (LVD) 2014/35/EU LV MFMTM Filter Rev 1.3 Page 10 of 1610/2018 MFM1714x50M50C5yzz Environmental Qualification Testing Activity Reference Standard Test Details HTOB-HTOL High-Temperature Operating Bias/Life JESD22-A110-B Duration of 1000hrs, high line, full load, max operating temperature, power cycled per IPC9592 TC (Temperature Cycling) JESD22-A104D 1000 cycles -55 to 125C DP-0266 Low temp, high temp, rapid thermal cycling, random vibration test, combined stress test THB (Temperature Humidity Bias) JEDSD22-A101C Duration of 1000hrs, biased, 85C, 85%RH. HTS (High-Temperature Storage) JESD 22-A103-D Duration 1000hrs, no bias. Maximum storage temperature (125C) LTS (Low-Temperature Storage) JESD22-A119 Duration 1000hrs, no bias. Minimum storage temperature (-65C) Random Vibration MIL-STD-810G Method 514.6, Procedure I, Category 24, mounted on QA Mechanical Shock MIL-STD-810G Method 516.5, Procedure I, Environment: functional shock 40G, mounted on QA HALT (Highly-Accelerated Life Test) Electro Static Discharge Human Body Model Electro Static Discharge Device Charge Model Free Fall Term Strength Through-Hole Solderability JEDEC JS-001-2012 JESD22-C101-E IPC9592B MIL-STD-202G IPC-9592B Table 2B, Class 2, 2000V minimum Class III 500V minimum IEC 60068-2-32, Freefall Procedure 1 Method 211A, Test Condition A, Environment: ambient temperature & %Rh. IPC/ECA J-STD-002 Test A (dip and look) Salt Fog MIL-STD-810G Method 509.5 Fungus MIL-STD-810G Method 508.6 Resistance to Solvents MIL-STD-202G Method 215K Acceleration MIL-STD-810G Method 513.6 Procedure II Altitude MIL-STD-810G Method 500.5 Procedure I & II Explosive Atmosphere MIL-STD-810G Method 511.5 Procedure I, operational LV MFMTM Filter Rev 1.3 Page 11 of 1610/2018 MFM1714x50M50C5yzz Thermal Considerations The LV MFM must be operated such that the internal components are kept within the maximum of the operating temperature range by monitoring/controlling the temperature of both the non-pinside plastic housing and the output terminals. A simplified thermal circuit model of the LV MFM is shown below in Figure 15. In this thermal-circuit model, thermal resistance is in units of C/W is analogous to electrical resistance, temperature in C is analogous to voltage, and the rate of heat transferred in W is analogous to current. The maximum internal temperature of the LV MFM can be estimated based on total power dissipated by the MFM, the temperature maintained on the non-pin side of the housing, and the temperature of the output terminals. In the example shown in Figure 15, the non-pin side of the plastic housing is maintained at 70C, the output terminals are measured to be about 100C, and the LV MFM is dissipating 9W of heat. The resultant maximum internal temperature of the LV MFM can then be estimated at 124C, which is close to the maximum operating temperature. 4W of heat is conducted through the lower housing, and the remaining 5W is conducted through the output terminals. The LV MFM is best attached to a material with a high thermal conductivity (e.g., aluminum or copper) to maintain temperature uniformity across the non-pin-side plastic housing. Maximum Internal Temperature 124C INT_OUT_TERMINALS 14 NON_PIN_SIDE 4.7 PDISS 9W TNON_PIN_SIDE 70C TOUTPUT_TERMINATION 100C Figure 15 -- LV MFM thermal model LV MFMTM Filter Rev 1.3 Page 12 of 1610/2018 MFM1714x50M50C5yzz Chassis-Mount Outline Drawing PIN 1 DESIGNATOR .11 2.89 1.170 29.720 .88 22.28 .15 3.86 (2) PL. +IN +OUT EMI GND 1.40 35.50 -IN -OUT .37.015 9.30.381 1.76 44.60 81/(6627+(5:,6(63(&,),('',0(16,216$5(,1&+>00@ LV MFMTM Filter Rev 1.3 Page 13 of 1610/2018 MFM1714x50M50C5yzz Board-Mount Outline Drawing 1.76 44.60 .88 22.30 .11 2.89 1.170 29.720 1.40 35.50 TOP VIEW (COMPONENT SIDE) .37.015 9.30.381 SEATING PLANE .080 2.032 (5) PL. DIM 'L'.015 (5) PL. DIM 'L' .120 [3.036] .199 [5.042] SHORT LONG 1.396.020 35.458.508 .698.020 17.729.508 +IN .474.020 12.029.508 (2) PL. +OUT EMI GND .947.020 24.058.508 -IN -OUT .111.020 2.825.508 (2) PL. .152 3.861 (2) PL. BOTTOM VIEW 1.396.003 35.452.076 .698.003 17.726.076 -IN -OUT EMI GND .474.003 12.029.076 (2) PL. .947.003 24.058.076 +OUT +IN .120.003 3.048.076 PLATED THRU .030 [.762] ANNULAR RING (5) PL. .172.003 4.369.076 PLATED THRU .064 [1.626] ANNULAR RING (2) PL. .111.003 2.831.076 RECOMMENDED HOLE PATTERN (COMPONENT SIDE) 81/(6627+(5:,6(63(&,),('',0(16,216$5(,1&+>00@ LV MFMTM Filter Rev 1.3 Page 14 of 1610/2018 1.170.003 29.720.076 MFM1714x50M50C5yzz Revision History Revision Date Description 1.0 06/07/17 Initial Release n/a 1.1 07/26/17 Added fuse recommendation for typical application & remvoed MOV Updated internal operting temperature Updated note on CE scans for -OUT floating Updated MTBF rating 2 4 7, 8 10 1.2 07/17/18 Added input line transient suppression block diagram Updated mechanical drawings 1.3 10/23/18 Updated features & benefits Added reverse-polarity protection specifications LV MFMTM Filter Rev 1.3 Page 15 of 1610/2018 Page Number(s) 9 13, 14 1 4 MFM1714x50M50C5yzz Vicor's comprehensive line of power solutions includes high density AC-DC and DC-DC modules and accessory components, fully configurable AC-DC and DC-DC power supplies, and complete custom power systems. Information furnished by Vicor is believed to be accurate and reliable. However, no responsibility is assumed by Vicor for its use. Vicor makes no representations or warranties with respect to the accuracy or completeness of the contents of this publication. Vicor reserves the right to make changes to any products, specifications, and product descriptions at any time without notice. Information published by Vicor has been checked and is believed to be accurate at the time it was printed; however, Vicor assumes no responsibility for inaccuracies. Testing and other quality controls are used to the extent Vicor deems necessary to support Vicor's product warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. Specifications are subject to change without notice. Visit http://www.vicorpower.com/mil-cots-dc-dc/mfm-filter-module for the latest product information. Vicor's Standard Terms and Conditions and Product Warranty All sales are subject to Vicor's Standard Terms and Conditions of Sale, and Product Warranty which are available on Vicor's webpage (http://www.vicorpower.com/termsconditionswarranty) or upon request. Life Support Policy VICOR'S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS PRIOR WRITTEN APPROVAL OF THE CHIEF EXECUTIVE OFFICER AND GENERAL COUNSEL OF VICOR CORPORATION. As used herein, life support devices or systems are devices which (a) are intended for surgical implant into the body, or (b) support or sustain life and whose failure to perform when properly used in accordance with instructions for use provided in the labeling can be reasonably expected to result in a significant injury to the user. A critical component is any component in a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system or to affect its safety or effectiveness. Per Vicor Terms and Conditions of Sale, the user of Vicor products and components in life support applications assumes all risks of such use and indemnifies Vicor against all liability and damages. Intellectual Property Notice Vicor and its subsidiaries own Intellectual Property (including issued U.S. and Foreign Patents and pending patent applications) relating to the products described in this data sheet. No license, whether express, implied, or arising by estoppel or otherwise, to any intellectual property rights is granted by this document. Interested parties should contact Vicor's Intellectual Property Department. The products described on this data sheet are protected by the following U.S. Patents Numbers: Patents Pending. Contact Us: http://www.vicorpower.com/contact-us Vicor Corporation 25 Frontage Road Andover, MA, USA 01810 Tel: 800-735-6200 Fax: 978-475-6715 www.vicorpower.com email Customer Service: custserv@vicorpower.com Technical Support: apps@vicorpower.com (c)2017 - 2018 Vicor Corporation. All rights reserved. The Vicor name is a registered trademark of Vicor Corporation. All other trademarks, product names, logos and brands are property of their respective owners. LV MFMTM Filter Rev 1.3 Page 16 of 1610/2018