LTC4120/LTC4120-4.2 Wireless Power Receiver and 400mA Buck Battery Charger FEATURES n n n n n n n n n n DESCRIPTION Dynamic Harmonization Control Optimizes Wireless Charging Over a Wide Coupling Range Wide Input Voltage Range (12.5V to 40V) Adjustable Float Voltage (3.5V to 11V) Fixed 4.2V Float Voltage Option (LTC4120-4.2) 50mA to 400mA Charge Current Programmed with a Single Resistor 1% Feedback Voltage Accuracy Programmable 5% Accurate Charge Current No Microprocessor Required No Transformer Core Thermally Enhanced, Low Profile 16-Lead (3mm x 3mm x 0.75mm) QFN Package The LTC(R)4120 is a constant-current/constant-voltage wireless receiver and battery charger. An external programming resistor sets the charge current up to 400mA. The LTC4120-4.2 is suitable for charging Li-Ion/Polymer batteries, while the programmable float voltage of the LTC4120 accommodates several battery chemistries. The LTC4120 uses a Dynamic Harmonization Control (DHC) technique that allows high efficiency contactless charging across an air gap. The LTC4120 regulates its input voltage via the DHC pin. This technique modulates the resonant frequency of a receiver tank to automatically adjust the power received as well as the power transmitted to provide an efficient solution for wirelessly charging battery-powered devices. Wireless charging with the LTC4120 provides a method to power devices in harsh environments without requiring expensive failure-prone connectors. This allows products to be charged while locked within sealed enclosures, or in moving or rotating equipment, or where cleanliness or sanitation is critical. APPLICATIONS n n n n n n Handheld Instruments Industrial/Military Sensors and Devices Harsh Environments Portable Medical Devices Physically Small Devices Electrically Isolated Devices This full featured battery charger includes accurate RUN pin threshold, low voltage battery preconditioning and bad battery fault detection, timer termination, auto-recharge, and NTC temperature qualified charging. The FAULT pin provides an indication of bad battery or temperature faults. All registered trademarks and trademarks are the property of their respective owners. Once charging is terminated, the LTC4120 signals end-ofcharge via the CHRG pin, and enters a low current sleep mode. An auto-restart feature starts a new charging cycle if the battery voltage drops by 2.2%. TYPICAL APPLICATION Wireless Rx Voltage/Charge Current vs Spacing 26.7nF LTC4120 6.5nF Tx CIRCUITRY DHC SW 22nF 35 33H 47H BAT FAULT 1.01M CHRG FB GND PROG FBG 3.01k Li-Ion 4.2V ICHARGE MAX + 333 VIN 30 CHGSNS NTC 5H 400 40 2.2F 267 NOT CHARGING 25 200 133 20 T CHARGING 15 1.35M 22F 4120 TA01a 10 0.4 CHARGE CURRENT (mA) 10F INTVCC FREQ BOOST VIN(RX) (V) IN RUN 67 0.6 0.8 1.0 1.2 1.4 SPACING (cm) 1.6 0 1.8 4120 TA01b Rev. G Document Feedback For more information www.analog.com 1 LTC4120/LTC4120-4.2 ABSOLUTE MAXIMUM RATINGS (Note 1) IN, RUN, CHRG, FAULT, DHC....................... -0.3V to 43V BOOST.................................... VSW - 0.3V to (VSW + 6V) SW (DC)......................................... -0.3V to (VIN + 0.3V) SW (Pulsed <100ns).......................-1.5V to (VIN + 1.5V) CHGSNS, BAT, FBG, FB................................-0.3V to 12V FREQ, NTC, PROG, INTVCC........................... -0.3V to 6V ICHGSNS, IBAT...................................................... 600mA IDHC................................................................ 350mARMS ICHRG , IFAULT, IFBG...................................................5mA IFB ..........................................................................5mA IINTVCC................................................................... -5mA Operating Junction Temperature Range (Note 2)................................................... -40C to 125C Storage Temperature Range................... -65C to 150C PIN CONFIGURATION LTC4120-4.2 16 15 14 13 11 FBG BOOST 2 17 GND 5 6 7 8 GND DHC FREQ CHGSNS SW 4 10 FB IN 3 9 BAT SW 4 UD PACKAGE 16-LEAD (3mm x 3mm) PLASTIC QFN TJMAX = 125C, JA = 54C/W EXPOSED PAD (PIN 17) IS GND, MUST BE SOLDERED TO PCB TO OBTAIN JA 12 NTC 11 NC 17 GND 10 BATSNS 9 5 6 7 8 CHGSNS BOOST 2 FREQ INTVCC 1 DHC 12NTC GND INTVCC 1 IN 3 PROG RUN 16 15 14 13 CHRG TOP VIEW PROG CHRG FAULT RUN TOP VIEW FAULT LTC4120 BAT UD PACKAGE 16-LEAD (3mm x 3mm) PLASTIC QFN TJMAX = 125C, JA = 54C/W EXPOSED PAD (PIN 17) IS GND, MUST BE SOLDERED TO PCB TO OBTAIN JA ORDER INFORMATION LEAD FREE FINISH TAPE AND REEL PART MARKING* PACKAGE DESCRIPTION TEMPERATURE RANGE LTC4120EUD#PBF LTC4120EUD#TRPBF LGHB 16-Lead (3mm x 3mm) Plastic QFN -40C to 125C LTC4120IUD#PBF LTC4120IUD#TRPBF LGHB 16-Lead (3mm x 3mm) Plastic QFN -40C to 125C LTC4120EUD-4.2#PBF LTC4120EUD-4.2#TRPBF LGMT 16-Lead (3mm x 3mm) Plastic QFN -40C to 125C LTC4120IUD-4.2#PBF LTC4120IUD-4.2#TRPBF 16-Lead (3mm x 3mm) Plastic QFN -40C to 125C LGMT Contact the factory for parts specified with wider operating temperature ranges. *The temperature grade is identified by a label on the shipping container. Tape and reel specifications. Some packages are available in 500 unit reels through designated sales channels with #TRMPBF suffix. 2 LTC4120 OPTIONS FLOAT VOLTAGE LTC4120 Programmable LTC4120-4.2 4.2V Fixed Rev. G For more information www.analog.com LTC4120/LTC4120-4.2 ELECTRICAL CHARACTERISTICS The l denotes the specifications which apply over the specified operating junction temperature range, otherwise specifications are at TA = 25C (Note 2). VIN = VRUN = 15V, VCHGSNS = VBAT = 4V, RPROG = 3.01k, VFB = 2.29V (LTC4120), VBATSNS = 4V (LTC4120-4.2). Current into a pin is positive out of the pin is negative. SYMBOL PARAMETER CONDITIONS Operating Input Supply Range MIN l Battery Voltage Range IIN VDUVLO UVINTVCC DC Supply Current TYP 12.5 40 0 Switching, FREQ = GND MAX 11 3.5 UNITS V V mA Standby Mode (Note 3) l 130 220 A Sleep Mode (Note 3) LTC4120: VFB = 2.51V (Note 5), LTC4120-4.2: VBATSNS = 4.4V l 60 100 A Disabled Mode (Note 3) l 37 70 A Shutdown Mode (Note 3) l Differential Undervoltage Lockout VIN-VBAT Falling, VIN = 5V (LTC4120), VIN-VBATSNS Falling, VIN = 5V (LTC4120-4.2) l Hysteresis VIN-VBAT Rising, VIN = 5V (LTC4120), VIN-VBATSNS Rising, VIN = 5V (LTC4120-4.2) INTVCC Undervoltage Lockout INTVCC Rising, VIN = INTVCC + 100mV, VBAT = NC Hysteresis INTVCC Falling (Note 4) 20 20 40 A 80 160 mV 115 l 4.00 4.15 mV 4.26 220 V mV Battery Charger IBAT BAT Standby Current Standby Mode (LTC4120) (Notes 3, 7, 8) Standby Mode (LTC4120-4.2) (Notes 3, 7, 8) l l 2.5 50 4.5 1000 A nA BAT Shutdown Current Shutdown Mode (LTC4120) (Notes 3, 7, 8) Shutdown Mode (LTC4120-4.2) (Notes 3, 7, 8) l l 1100 10 2000 1000 nA nA BATSNS Standby Current (LTC4120-4.2) Standby Mode (Notes 3, 7, 8) l 5.4 10 A BATSNS Shutdown Current (LTC4120-4.2) Shutdown Mode (Notes 3, 7, 8) l 1100 2000 nA IFB Feedback Pin Bias Current (LTC4120) VFB = 2.5V (Notes 5, 7) l 25 60 nA IFBG(LEAK) Feedback Ground Leakage Current (LTC4120) Shutdown Mode (Notes 3, 7) l 1 A RFBG Feedback Ground Return Resistance (LTC4120) l 1000 2000 VFB(REG) Feedback Regulation Voltage (LTC4120) IBATSNS VFLOAT (Note 5) 2.393 2.370 2.400 l 2.407 2.418 V V 4.188 4.148 4.200 l 4.212 4.227 V V l l 383 45 402 50 421 55 Regulated Float Voltage (LTC4120-4.2) ICHG Battery Charge Current RPROG = 3.01k RPROG = 24.3k VUVCL Undervoltage Current Limit VIN Falling 12.0 mA mA V VRCHG Battery Recharge Threshold VFB Falling Relative to VFB_REG (LTC4120) (Note 5) l -38 -50 -62 mV VRCHG_4.2 Battery Recharge Threshold VBATSNS Falling Relative to VFLOAT (LTC4120-4.2) l -70 -92 -114 mV hPROG Ratio of BAT Current to PROG Current VTRKL < VFB < VFB(REG) (LTC4120) (Note 5) VTRKL_4.2 < VBATSNS < VFLOAT (LTC4120-4.2) VPROG PROG Pin Servo Voltage RSNS CHGSNS-BAT Sense Resistor 988 l IBAT = -100mA 1.206 1.227 300 mA/mA 1.248 V m Rev. G For more information www.analog.com 3 LTC4120/LTC4120-4.2 ELECTRICAL CHARACTERISTICS The l denotes the specifications which apply over the specified operating junction temperature range, otherwise specifications are at TA = 25C (Note 2). VIN = VRUN = 15V, VCHGSNS = VBAT = 4V, RPROG = 3.01k, VFB = 2.29V (LTC4120), VBATSNS = 4V (LTC4120-4.2). Current into a pin is positive out of the pin is negative. SYMBOL PARAMETER CONDITIONS ILOWBAT Low Battery Linear Charge Current 0V < VFB < VTRKL, VBAT = 2.6V (LTC4120), VBATSNS < VTRKL_4.2, VBAT = 2.6V (LTC4120-4.2) VLOWBAT Low Battery Threshold Voltage VBAT Rising (LTC4120), VBATSNS Rising (LTC4120-4.2) l MIN TYP MAX 6 9 16 2.15 2.21 2.28 Hysteresis ITRKL VTRKL VTRKL_4.2 hC/10 UNITS mA V 147 mV Switch Mode Trickle Charge Current VLOWBAT < VBAT, VFB < VTRKL (LTC4120) (Note 5), VLOWBAT < VBATSNS < VTRKL_4.2 (LTC4120-4.2) ICHG/10 mA PROG Pin Servo Voltage in Switch Mode Trickle Charge VLOWBAT < VBAT, VFB < VTRKL (LTC4120) (Note 5), VLOWBAT < VBATSNS < VTRKL_4.2 (LTC4120-4.2) 122 mV Trickle Charge Threshold VFB Rising (LTC4120) (Note 5) Hysteresis VFB Falling (LTC4120) (Note 5) Trickle Charge Threshold VBATSNS Rising (LTC4120-4.2) Hysteresis VBATSNS Falling (LTC4120-4.2) End of Charge Indication Current Ratio (Note 6) l 1.64 1.68 l 2.86 2.91 1.71 50 V mV 2.98 88 V mV 0.1 mA/mA Safety Timer Termination Period 1.3 2.0 2.8 Hours Bad Battery Termination Timeout 19 30 42 Minutes 1.0 0.5 1.5 0.75 2.0 1.0 MHz MHz Switcher fOSC Switching Frequency FREQ = INTVCC FREQ = GND tMIN(ON) Minimum Controllable On-Time (Note 9) Duty Cycle Maximum (Note 9) Top Switch RDS(ON) ISW = -100mA 0.8 Bottom Switch RDS(ON) ISW = 100mA 0.5 IPEAK Peak Current Limit Measured Across RSNS with a 15H Inductor in Series with RSNS (Note 9) ISW Switch Pin Current (Note 8) VIN = Open-Circuit, VRUN = 0V, VSW = 8.4V (LTC4120) l l VIN = Open-Circuit, VRUN = 0V, VSW = 4.2V (LTC4120-4.2) l l 120 ns 94 585 % 750 1250 mA 15 7 30 15 A A 500 mV 0 1 A Status Pins FAULT, CHRG Pin Output Voltage Low I = 2mA Pin Leakage Current V = 43V, Pin High Impedance Cold Temperature VNTC/VINTVCC Fault Rising VNTC Threshold Falling VNTC Threshold l 73 74 72 75 %INTVCC %INTVCC Hot Temperature VNTC/VINTVCC Fault Falling VNTC Threshold Rising VNTC Threshold l 35.5 36.5 37.5 37.5 %INTVCC %INTVCC NTC Disable Voltage Falling VNTC Threshold Rising VNTC Threshold l 1 2 3 3 %INTVCC %INTVCC NTC Input Leakage Current VNTC = VINTVCC 50 nA NTC 4 -50 Rev. G For more information www.analog.com LTC4120/LTC4120-4.2 ELECTRICAL CHARACTERISTICS The l denotes the specifications which apply over the specified operating junction temperature range, otherwise specifications are at TA = 25C (Note 2). VIN = VRUN = 15V, VCHGSNS = VBAT = 4V, RPROG = 3.01k, VFB = 2.29V (LTC4120), VBATSNS = 4V (LTC4120-4.2). Current into a pin is positive out of the pin is negative. SYMBOL PARAMETER CONDITIONS MIN TYP MAX 2.35 2.45 2.55 UNITS RUN VEN VSD Enable threshold VRUN Rising Hysteresis VRUN Falling Run Pin Input Current VRUN = 40V Shutdown Threshold (Note 3) VRUN Falling l 200 0.01 l 0.4 Hysteresis V mV 0.1 1.2 220 A V mV FREQ FREQ Pin Input Low l FREQ Pin Input High VINTVCC-VFREQ FREQ Pin Input Current 0V < VFREQ < VINTVCC 0.4 V l 0.6 V 1 A Dynamic Harmonization Control VIN(DHC) Input Regulation Voltage DHC Pin Current VDHC = 1V, VIN < VIN(DHC) Note 1: Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. Exposure to any Absolute Maximum Rating condition for extended periods may affect device reliability and lifetime. Note 2: The LTC4120 is tested under pulsed load conditions such that TJ TA. The LTC4120E is guaranteed to meet performance specifications for junction temperatures from 0C to 85C. Specifications over the -40C to 125C operating junction temperature range are assured by design, characterization and correlation with statistical process controls. The LTC4120I is guaranteed over the full -40C to 125C operating junction temperature range. Note that the maximum ambient temperature consistent with these specifications is determined by specific operating conditions in conjunction with board layout, the rated package thermal impedance, and other environmental factors. Note 3: Standby mode occurs when the LTC4120 stops switching due to an NTC fault condition, or when the charge current has dropped low enough to enter Burst Mode operation. Disabled mode occurs when VRUN is between VSD and VEN. Shutdown mode occurs when VRUN is below VSD or when the differential undervoltage lockout is engaged. SLEEP mode occurs after a timeout while the battery voltage remains above the VRCHG or VRCHG_42 threshold. 14 V 330 mARMS Note 4: The internal supply INTVCC should only be used for the NTC divider, it should not be used for any other loads. Note 5: The FB pin is measured with a resistance of 588k in series with the pin. Note 6: hC/10 is expressed as a fraction of measured full charge current as measured at the PROG pin voltage when the CHRG pin de-asserts. Note 7: In an application circuit with an inductor connected from SW to CHGSNS, the total battery leakage current when disabled is the sum of IBAT, IFBG(LEAK) and ISW (LTC4120), or IBATSNS and IBAT and ISW (LTC4120-4.2). Note 8: When no supply is present at IN, the SW powers IN through the body diode of the topside switch. This may cause additional SW pin current depending on the load present at IN. Note 9: Guaranteed by design and/or correlation to static test. Rev. G For more information www.analog.com 5 LTC4120/LTC4120-4.2 TYPICAL PERFORMANCE CHARACTERISTICS TA = 25C, unless otherwise noted. Typical VFLOAT vs Temperature LTC4120-4.2 Typical VFB(REG) vs Temperature 2.43 4.25 4 UNITS TESTED 4 UNITS TESTED 4.24 2.42 4.23 HIGH LIMIT DUT1 VFB(REG) (V) DUT2 VFB(REG) (V) DUT3 VFB(REG) (V) DUT4 VFB(REG) (V) LOW LIMIT DUT = DEVICE UNDER TEST 2.40 2.39 2.38 2.37 4.22 VFLOAT (V) VFB(REG) (V) 2.41 HIGH LIMIT DUT1 VFLOAT DUT2 VFLOAT DUT3 VFLOAT DUT4 VFLOAT LOW LIMIT 4.21 4.20 4.19 4.18 4.17 4.16 2.36 -40 -25 -10 5 20 35 50 65 80 95 110 125 TEMPERATURE (C) 4.15 -40 -25 -10 5 20 35 50 65 80 95 110 125 TEMPERATURE (C) 4120 G01 4120 G20 IN Pin Standby/Sleep Current vs Temperature 180 IN Pin Disabled/Shutdown Current vs Temperature 60 2 UNITS TESTED VIN = 15V 50 IIN (A) 140 IIN STANDBY FREQ = INTVCC IIN STANDBY FREQ = INTVCC IIN STANDBY FREQ = GND IIN STANDBY FREQ = GND IIN SLEEP IIN SLEEP 120 100 80 40 IIN (A) 160 2 UNITS TESTED VIN = 15V IIN DISABLED IIN DISABLED 30 20 IIN SD IIN SD 10 60 40 -50 -25 50 25 75 0 TEMPERATURE (C) 100 0 -50 -25 125 50 25 75 0 TEMPERATURE (C) BAT Pin Sleep/Shutdown Current vs Temperature 5 IBAT SLEEP IBAT SLEEP 4 3 2 0 -50 -25 395 -50 -25 100 125 4120 G04 6 398 DUT1 DUT2 DUT3 1060 399 396 75 50 25 TEMPERATURE (C) 1080 400 1 0 1100 401 397 IBAT SHUTDOWN IBAT SHUTDOWN 1120 RPROG = 3.01k 2 UNITS TESTED FREQ = GND FREQ = GND FREQ = INTVCC FREQ = INTVCC 50 25 75 0 TEMPERATURE (C) 100 125 IPEAK (mA) IBAT (A) 6 402 ICHG (mA) 7 Typical RSNS Current Limit vs Temperature Typical Battery Charge Current vs Temperature 2 UNITS TESTED VBAT = 4.2V RFB2 = 1.01M RFB1 = 1.35M 125 4120 G03 4120 G02 8 100 1040 1020 1000 980 960 940 3 UNITS TESTED 920 50 75 -50 -25 0 25 TEMPERATURE (C) 100 125 4120 G06 4120 G05 Rev. G For more information www.analog.com LTC4120/LTC4120-4.2 TYPICAL PERFORMANCE CHARACTERISTICS Switching Frequency vs Temperature FREQ = GND FREQ = GND 0.6 0.4 16 90 14 85 12 300 10 250 8 200 6 150 80 75 VIN = 12.5V VIN = 14V VIN = 20V VIN = 30V 70 65 60 0.2 0 -50 -25 50 25 75 0 TEMPERATURE (C) 100 50 125 50 0 100 150 200 250 300 350 400 IBAT (mA) 4120 G07 130 70 EFFICIENCY (%) 110 105 100 95 90 85 100 50 20 40 18 30 16 20 14 10 12 0 125 50 0 100 150 200 Typical Wireless Charging Cycle 400 4.0 80 350 3.5 70 3.0 60 250 IBAT 2.5 200 2.0 150 BAT = 940mAhr LSW = TDK SLF4075 15H 100 RFB1 = 732k, RFB2 = 976k RPROG = 3.01k 50 APPLICATION CCT OF FIGURE 10 SPACING = 14mm 0 2 0 1 TIME (HOURS) 1.5 3 4120 G12 IBAT (mA) 300 VCHRG 10 250 RPROG = 3k VSW 5V/DIV RPROG = 6.2k 50 0V VPROG 500mV/DIV 0V ILSW 200mA/DIV 0mA 40 30 1.0 20 0.5 10 0 9mm EFFICIENCY 10mm EFFICIENCY 11mm EFFICIENCY 9mm V_RX 10mm V_RX 11mm V_RX Typical Burst Mode Waveforms, IBAT = 38mA 90 VBAT, VCHRG (V) BATTERY CURRENT (mA) 4.5 0 125 4120 G11 Burst Mode Trigger Current VBAT 100 IBAT (mA) 4120 G10 450 50 22 VIN_RX (V) tMIN(0N) (ns) 115 50 25 0 75 TEMPERATURE (C) 100 24 VFLOAT = 8.3V LSW = SLF6028-470MR59 RPROG = 4.64k 60 120 -22 350 Wireless Power Transfer Efficiency, VIN_RX vs Battery Current 2 UNITS TESTED 80 -50 400 4120 G09 4120 G08 Typical tMIN(ON) vs Temperature 125 VIN = OPEN-CIRCUIT VBAT = 4.2V 2 UNITS TESTED 4 IBAT IBAT 2 VBAT-VIN VBAT-VIN 0 0 50 75 25 -50 -25 TEMPERATURE (C) LSW = 68H, SLF12555T-680M1R3 FREQ = GND VBAT = 4.2V 55 2 UNITS TESTED IBAT (A) fOSC (MHz) 0.8 95 VBAT-VIN (mV) EFFICIENCY (%) FREQ = INTVCC FREQ = INTVCC 1.0 BAT Pin Leakage Current/VBAT-VIN vs Temperature Buck Efficiency vs Battery Current 1.4 1.2 TA = 25C, unless otherwise noted. 0 4s/DIV 10 15 20 25 VIN (V) 30 4120 G14 40 35 4120 G13 Rev. G For more information www.analog.com 7 LTC4120/LTC4120-4.2 TYPICAL PERFORMANCE CHARACTERISTICS TA = 25C, unless otherwise noted. IN Pin Shutdown Current vs Input Voltage IN Pin Standby Current vs VIN 220 80 VBAT = 4.21V NTC = GND 200 60 IIN STBY FREQ HIGH 130C IIN STBY FREQ LOW 130C IIN STBY FREQ HIGH 25C IIN STBY FREQ LOW 25C IIN STBY FREQ HIGH -45C IIN STBY FREQ LOW -45C 160 140 120 50 IIN (A) IIN (A) 180 40 30 20 100 80 VRUN = 0.4V 70 IIN SD TEMP = 125C IIN SD TEMP = 35C IIN SD TEMP = -40C 10 0 5 10 15 20 25 VIN (V) 30 35 0 40 0 10 20 4120 G15 IN Pin Switching Current vs Input Voltage 7 VRUN = 1.6V 90 80 -45C IICCQ(SWITCHING) FREQ HIGH FREQ = INTVCC 50 40 30 4 3 2 IIN SD TEMP = 125C IIN SD TEMP = 35C IIN SD TEMP = -40C 10 0 10 20 VIN (V) 30 40 1 0 10 UVCL 25 30 35 VIN (V) 4120 G17 8 0.20 0.15 0.05 IBAT = 0 20 0.25 0.10 IICCQ(SWITCHING) FREQ LOW FREQ = GND 15 IBAT TEMP = 125C IBAT TEMP = 35C IBAT TEMP= -40C 0.30 ICHARGE (mA) 60 IIN (mA) IIN (A) 25C 0.35 5 70 0 130C UVCL: ICHARGE vs Input Voltage 0.40 6 20 40 4120 G16 IN Pin Disabled Current vs Input Voltage 100 30 VIN (V) 40 4120 G18 0 11.90 11.95 12.00 12.05 12.10 12.15 12.20 VIN (V) 4120 G19 Rev. G For more information www.analog.com LTC4120/LTC4120-4.2 PIN FUNCTIONS INTVCC (Pin 1): Internal Regulator Output Pin. This pin is the output of an internal linear regulator that generates the internal INTVCC supply from IN. It also supplies power to the switch gate drivers and the low battery linear charge current ILOWBAT. Connect a 2.2F low ESR capacitor from INTVCC to GND. Do not place any external load on INTVCC other than the NTC bias network. Overloading this pin can disrupt internal operation. When the RUN pin is above VEN, and INTVCC rises above the UVLO threshold, and IN rises above BAT by VDUVLO and its hysteresis, the charger is enabled. BOOST (Pin 2): Boosted Supply Pin. Connect a 22nF boost capacitor from this pin to the SW pin. IN (Pin 3): Positive Input Power Supply. Decouple to GND with a 10F or larger low ESR capacitor. SW (Pin 4): Switch Pin. The SW pin delivers power from IN to BAT via the step-down switching regulator. An inductor should be connected from SW to CHGSNS. See the Applications Information section for a discussion of inductor selection. GND (Pin 5, Exposed Pad Pin 17): Ground Pin. Connect to exposed pad. The exposed pad must be soldered to PCB GND to provide a low electrical and thermal impedance connection to ground. DHC (Pin 6): Dynamic Harmonization Control Pin. Connect a Schottky diode from the DHC pin to the IN pin, and a capacitor from the DHC pin as shown in the Typical Application or the Block Diagram. When VIN is greater than VIN(DHC), this pin is high impedance. When VIN is below VIN(DHC) this pin is low impedance allowing the LTC4120 to modulate the resonance of the tuned receiver network. See Applications Information for more information on the tuned receiver network. FREQ (Pin 7): Buck Switching Frequency Select Input Pin. Connect to INTVCC to select a 1.5MHz switching frequency or GND to select a 750kHz switching frequency. Do not float. CHGSNS (Pin 8): Battery Charge Current Sense Pin. An internal current sense resistor between CHGSNS and BAT pins monitors battery charge current. An inductor should be connected from SW to CHGSNS. BAT (Pin 9): Battery Output Pin. Battery charge current is delivered from this pin through the internal charge current sense resistor. In low battery conditions a small linear charge current, ILOWBAT, is sourced from this pin to precondition the battery. Decouple the BAT pin with a low ESR 22F or greater ceramic capacitor to GND. BATSNS (Pin 10, LTC4120-4.2 Only): Battery Voltage Sense Pin. For proper operation, this pin must always be connected physically close to the positive battery terminal. FB (Pin 10, LTC4120 Only): Battery Voltage Feedback Pin. The charge function operates to achieve a final float voltage of 2.4V at this pin. Battery float voltage is programmed using a resistive divider from BAT to FB to FBG, and can be programmed up to 11V. The feedback pin input bias current, IFB, is 25nA. Using a resistive divider with a Thevenin equivalent resistance of 588k compensates for input bias current error (see curve of FB Pin Bias Current versus Temperature in the Typical Performance Characteristics). FBG (Pin 11, LTC4120 Only): Feedback Ground Pin. This pin disconnects the external FB divider load from the battery when it is not needed. When sensing the battery voltage this pin presents a low resistance, RFBG, to GND. When in disabled or shutdown modes this pin is high impedance. NTC (Pin 12): Input to the Negative Temperature Coefficient Thermistor Monitoring Circuit. The NTC pin connects to a negative temperature coefficient thermistor which is typically co-packaged with the battery to determine if the battery is too hot or too cold to charge. If the battery's temperature is out of range, the LTC4120 enters standby mode and charging is paused until the battery temperature re-enters the valid range. A low drift bias resistor is required from INTVCC to NTC and a thermistor is required from NTC to GND. Tie the NTC pin to GND to disable NTC qualified charging if NTC functionality is not required. PROG (Pin 13): Charge Current Program and Charge Current Monitor Pin. Connect a 1% resistor between 3.01k (400mA) and 24.3k (50mA) from PROG to ground to program the charge current. While in constant-current mode, this pin regulates to 1.227V. The voltage at this pin represents the average battery charge current using the following formula: I BAT = hPROG * For more information www.analog.com VPROG RPROG Rev. G 9 LTC4120/LTC4120-4.2 PIN FUNCTIONS where hPROG is typically 988. Keep parasitic capacitance on the PROG pin to a minimum. CHRG (Pin 14): Open-Drain Charge Status Output Pin. Typically pulled up through a resistor to a reference voltage, the CHRG pin indicates the status of the battery charger. The pin can be pulled up to voltages as high as IN when disabled, and can sink currents up to 5mA when enabled. When the battery is being charged, the CHRG pin is pulled low. When the termination timer expires or the charge current drops below 10% of the programmed value, the CHRG pin is forced to a high impedance state. FAULT (Pin 15): Open-Drain Fault Status Output Pin. Typically pulled up through a resistor to a reference voltage, this status pin indicates fault conditions during a charge cycle. The pin can be pulled up to voltages as high as IN when disabled, and can sink currents up to 5mA when enabled. An NTC temperature fault causes this pin to be pulled low. A bad battery fault also causes this pin to be pulled low. If no fault conditions exist, the FAULT pin remains high impedance. RUN (Pin 16): Run Pin. When RUN is pulled below VEN and its hysteresis, the device is disabled. In disabled mode, battery charge current is zero and the CHRG and FAULT pins assume high impedance states. If the voltage at RUN is pulled below VSD, the device is in shutdown mode. When the voltage at the RUN pin rises above VEN, the INTVCC LDO turns on. When the INTVCC LDO rises above its UVLO threshold the charger is enabled. The RUN pin should be tied to a resistive divider from VIN to program the input voltage at which charging is enabled. Do not float the RUN pin. BLOCK DIAGRAM C2S 3 16 CIN 10F RUN 2.45V + - 0.9V + - C2P * BAT LR IN - 80mV 6 IN 7 15 DHC PWM BOOST DUVLO GND IN INTVCC ENABLE CNTRL LOWBAT INTVCC 1.2V 2 CBST 22nF 4 5 LSW 33H BAT 8 9 INTVCC - + FB 588k V-EA VFB(REG) FBG RFB1 10 RFB2 NTC NTC BAT 2.21V - + DZ + T 10k Li-Ion PROG HOT COLD DISABLE RNOM 10k CBAT 22F 11 ENABLE INTVCC 12 RSNS 0.3 C-EA + - UVCL CHGSNS + - IN ITH CHRG CINTVCC 2.2F INTVCC VIN(DHC) FREQ FAULT SW INTVCC 1 SHUTDOWN + - DHC INTVCC LDO INTVCC ENABLE IN 14 ENABLE LTC4120 IN 13 RPROG LOWBAT 4120 F01 Figure 1. Block Diagram 10 Rev. G For more information www.analog.com LTC4120/LTC4120-4.2 BLOCK DIAGRAM LTC4120-4.2 BATSNS IN - 80mV INTVCC ITH + - CHGSNS + - RSNS 0.3 C-EA DUVLO IN BATSNS INTVCC 9 10 CBAT 22F INTVCC + - 1.2V BAT 8 - + UVCL 588k + Li-Ion VFB(REG) V-EA ENABLE BATSNS 2.21V - + PROG LOWBAT 13 DZ RPROG 4120 F02 Figure 2. LTC4120-4.2 BATSNS Connections TEST CIRCUIT 20V 2k 665 680nF 49.9 IRLML5103TR VIN(DHC) IN NTC LTC4120 RUN 665 INTVCC 10 2.2F 10F DHC GND 4120 F03 Figure 3. VIN(DHC) Test Circuit Rev. G For more information www.analog.com 11 LTC4120/LTC4120-4.2 OPERATION Wireless Power System Overview The LTC4120 is one component in a complete wireless power system. A complete system is composed of transmit circuitry, a transmit coil, a receive coil and receive circuitry--including the LTC4120. Please refer to the Applications Information section for more information on transmit circuitry and coils. In particular, the Resonant Transmitter and Receiver and the Alternative Transmitter Options sections include information necessary to complete the design of a wireless power system. Further information can be found in the Applications Information section of this document under the heading Resonant Transmitter and Receiver, as well as in AN138: Wireless Power Users Guide, as well as the DC1969A: wireless power transmit and receiver demo kit and manual. The Gerber layout files for both the Transmitter and Receiver boards are available at the following link: LTC4120 Evaluation Kits LTC4120 Overview The LTC4120 is a synchronous step-down (buck) wireless battery charger with dynamic harmonization control (DHC). DHC is a highly efficient method of regulating the received input voltage in a resonant coupled power transfer application. The LTC4120 serves as a constant-current/ VDC 5V L1 The circuit in Figure 4 is a fully functional system using a basic current-fed resonant converter for the transmitter and a series resonant converter for the receiver with the LTC4120. The LTC4125 advanced transmitter may also be used with the LTC4120. For more information on transmitter design refer to Application Note 138: Wireless Power Users Guide. Wireless Power Transfer A wireless coupled power transfer system consists of a transmitter that generates an alternating magnetic field, and a receiver that collects power from that field. The ideal transmitter efficiently generates a large alternating current in the transmitter coil, LX. The push-pull currentfed resonant converter, shown in Figure 4, is an example of a basic power transmitter that may be used with the LTC4120. This transmitter typically operates at a frequency of approximately 130kHz; though the operating TRANSMITTER C2S L2 CX LX C4 constant-voltage battery charger with the following builtin charger functions: programmable charge current, programmable float voltage (LTC4120), battery precondition with half-hour timeout, precision shutdown/run control, NTC thermal protection, a 2-hour safety termination timer, and automatic recharge. The LTC4120 also provides output pins to indicate state of charge and fault status. LR C2P D9 D8 C5 IN DHC BOOST SW R1 R2 D2 D3 M1 D5, D8, D9: DFLS240L M2 D1 D4 D6 39V DFLZ39 CIN D5 LTC4120 CBST LSW CHGSNS BAT GND CBAT + Li-Ion 4120 F04 Figure 4. DC-AC Converter, Transmit/Receive Coils, Tuned Series Resonant Receiver and AC-DC Rectifier 12 Rev. G For more information www.analog.com LTC4120/LTC4120-4.2 OPERATION frequency varies depending on the load at the receiver and the coupling to the receiver coil. For LX = 5H, and CX = 300nF, the transmitter frequency is: fO 1 2 * * L X * CX = 130 kHz This transmitter typically generates an AC coil current of about 2.5ARMS. For more information on this transmitter, refer to AN138: Wireless Power Users Guide. The receiver consists of a coil, LR, configured in a resonant circuit followed by a rectifier and the LTC4120. The receiver coil presents a load reflected back to the transmitter through the mutual inductance between LR and LX. The reflected impedance of the receiver may influence the operating frequency of the transmitter. Likewise, the power output by the transmitter depends on the load at the receiver. The resonant coupled charging system, consisting of both the transmitter and LTC4120 charger, provides an efficient method for wireless battery charging as the power output by the transmitter varies automatically based on the power used to charge a battery. Dynamic Harmonization Control Dynamic harmonization control (DHC) is a technique for regulating the received input power in a wireless power transfer system. DHC modulates the impedance of the resonant receiver to regulate the voltage at the input to the LTC4120. When the input voltage to the LTC4120 is below the VIN(DHC) set point, the LTC4120 allows more power to appear at the receiver by tuning the receiver resonance closer to the transmitter resonance. If the input voltage exceeds VIN(DHC), the LTC4120 tunes the receiver resonance away from the transmitter, which reduces the power available at the receiver. The amount that the input power increases or decreases is a function of the coupling, the tuning capacitor, C2P, the receiver coil, LR, and the operating frequency. Figure 5 illustrates the components that implement the DHC function to automatically tune the resonance of the receiver. Capacitor C2S and inductor LR serve as a series resonator. Capacitor C2P and the DHC pin of the LTC4120 form a parallel resonance when the DHC pin is low impedance, and disconnect when the DHC pin is high impedance. C2P adjusts the receiver resonance to control the amount of power available at the input of the LTC4120. C2P also affects power dissipation in the LTC4120 due to the AC current being shunted by the DHC pin. For this reason it is not recommended to apply total capacitance in excess of 30nF at this pin. Using DHC, the LTC4120 automatically adjusts the power received depending on load requirements; typically the load is battery charge current. This technique results in significant power savings, as the power required by the transmitter automatically adjusts to the requirements at the receiver. Furthermore, DHC reduces the rectified voltage seen at the input of the LTC4120 under light load conditions when the battery is fully charged. C2S 1:n CX LX LR C2P D9 D8 CIN D5 IN LTC4120 DHC 4120 F05 Figure 5. Resonant Receiver Tank Rev. G For more information www.analog.com 13 LTC4120/LTC4120-4.2 OPERATION The design of the resonant receiver circuit (LR, C2S and C2P), the transmitter circuit, and the mutual inductance between LX and LR determines both the maximum unloaded voltage at the input to the LTC4120 as well as the maximum power available at the input to the LTC4120. The value and tolerances of these components must be selected with care for stable operation, for this reason it is recommended to only use components with tight tolerances. To understand the operating principle behind dynamic harmonization control (DHC), consider the following simplification. Here, a fixed-frequency transmitter is operating at a frequency fO = 130kHz. DHC automatically adjusts the impedance of the receiver tuned network so as to modulate the resonant frequency of the receiver between fT and fD. fT fD 1 2 * * L R * ( C2P + C2S ) Programming The Battery Float Voltage For the LTC4120, the battery float voltage is programmed by placing a resistive divider from the battery to FB and FBG as shown in Figure 6. The programmable battery float voltage, VFLOAT, is then governed by the following equation: VFLOAT = VFB(REG) * (RFB1 + RFB2 ) RFB2 where VFB(REG) is typically 2.4V. Due to the input bias current (IFB) of the voltage error amp (V-EA), care must also be taken to select the Thevenin equivalent resistance of RFB1||RFB2 close to 588k. Start by calculating RFB1 to satisfy the following relations: * 588k V RFB1 = FLOAT VFB(REG) Find the closest 0.1% or 1% resistor to the calculated value. With RFB1 calculate: 1 2 * * L R * C2S When the input voltage is above VIN(DHC) (typically 14V), the LTC4120 opens the DHC pin, detuning the receiver resonance away from the transmitter frequency fO, so that less power is received. When the input voltage is below VIN(DHC), the LTC4120 shunts the DHC pin to ground, tuning the receiver resonance closer to the transmitter frequency so that more power is available. For the resonant converter shown in Figure 4, the operating frequency of the transmitter is not fixed, but varies depending on the load impedance. However the basic operating principle of DHC remains valid. For more information on the design of the wireless power receiver resonant circuit refer to the applications section. RFB2 = VFB(REG) * RFB1 VFLOAT - VFB(REG) BAT LTC4120 IFB FB - 1000 VFLOAT RFB1 22F Li-Ion 4120 F06 FBG RFB2 ENABLE Figure 6. Programming the Float Voltage with the LTC4120 14 Rev. G For more information www.analog.com LTC4120/LTC4120-4.2 OPERATION where 1000 represent the typical value of RFBG. This is the resistance of the FBG pin which serves as the ground return for the battery float voltage divider. Once RFB1 and RFB2 are selected, recalculate the value of VFLOAT obtained with the resistors available. If the error is too large substitute another standard resistor value for RFB1 and recalculate RFB2. Repeat until the float voltage error is acceptable. Table 1 and Table 2 list recommended standard 0.1% and 1% resistor values for common battery float voltages. Table 1. Recommended 0.1% Resistors for Common VFLOAT VFLOAT 3.6V 4.1V 4.2V 7.2V 8.2V 8.4V RFB1 887k 1.01M 1.01M 1.8M 2.00M 2.05M RFB2 1780k 1.42M 1.35M 898k 825k 816k TYPICAL ERROR -0.13% 0.15% -0.13% 0.08% 0.14% 0.27% Table 2. Recommended 1% Resistors for Common VFLOAT VFLOAT 3.6V 4.1V 4.2V 7.2V 8.2V 8.4V RFB1 887k 1.02M 1.02M 1.78M 2.00M 2.1M RFB2 1780k 1.43M 1.37M 887k 825k 845k TYPICAL ERROR -0.13% 0.26% -0.34% 0.16% 0.14% -0.50% Programming the Charge Current The current-error amp (C-EA) measures the current through an internal 0.3 current sense resistor between the CHGSNS and BAT pins. The C-EA outputs a fraction of the charge current, 1/hPROG, to the PROG pin. The voltage-error amp (V-EA) and PWM control circuitry can limit the PROG pin voltage to control charge current. An internal clamp (DZ) limits the PROG pin voltage to VPROG, which in turn limits the charge current to: *V h 1212V I CHG = PROG PROG = RPROG RPROG hPROG * VPROG _ TRKL 120V I CHG _ TRKL = = RPROG RPROG where hPROG is typically 988, VPROG is either 1.227V or 122mV during trickle charge, and RPROG is the resistance of the grounded resistor applied to the PROG pin. The PROG resistor sets the maximum charge current, or the current delivered while the charger is operating in constant-current (CC) mode. Analog Charge Current Monitor The PROG pin provides a voltage signal proportional to the actual charge current. Care must be exercised in measuring this voltage as any capacitance at the PROG pin forms a pole that may cause loop instability. If observing the PROG pin voltage, add a series resistor of at least 2k and limit stray capacitance at this node to less than 50pF. In the event that the input voltage cannot support the demanded charge current, the PROG pin voltage may not represent the actual charge current. In cases such as this, the PWM switch frequency drops as the charger enters drop-out operation where the top switch remains on for more than one clock cycle as the inductor current attempts to ramp up to the desired current. If the top switch remains on in drop-out for 8 clock cycles a dropout detector forces the bottom switch on for the remainder of the 8th cycle. In such a case, the PROG pin voltage remains at 1.227V, but the charge current may not reach the desired level. Undervoltage Current Limit The undervoltage current limit (UVCL) feature reduces charge current as the input voltage drops below VUVCL Rev. G For more information www.analog.com 15 LTC4120/LTC4120-4.2 OPERATION (typically 12V). This low gain amplifier typically keeps VIN within 100mV of VUVCL, but if insufficient power is available the input voltage may drop below this value; and the charge current will be reduced to zero. NTC Thermal Battery Protection The LTC4120 monitors battery temperature using a thermistor during the charging cycle. If the battery temperature moves outside a safe charging range, the IC suspends charging and signals a fault condition until the temperature returns to the safe charging range. The safe charging range is determined by two comparators that monitor the voltage at the NTC pin. NTC qualified charging is disabled if the NTC pin is pulled below about 85mV (VDIS). Thermistor manufacturers usually include either a temperature lookup table identified with a characteristic curve number, or a formula relating temperature to the resistor value. Each thermistor is also typically designated by a thermistor gain value B25/85. The NTC pin should be connected to a voltage divider from INTVCC to GND as shown in Figure 7. In the simple application (RADJ = 0) a 1% resistor, RBIAS, with a value equal to the resistance of the thermistor at 25C is connected from INTVCC to NTC, and a thermistor is connected from NTC to GND. With this setup, the LTC4120 pauses charging when the resistance of the thermistor LTC4120 TOO COLD + - TOO HOT + - IGNORE NTC + - BAT INTVCC RBIAS NTC RADJ OPT 74% INTVCC 36.5% INTVCC RNTC T + The hot and cold trip points may be adjusted using a different type of thermistor, or a different RBIAS resistor, or by adding a desensitizing resistor, RADJ, or by a combination of these measures as shown in Figure 7. For example, by increasing RBIAS to 12.4k, with the same thermistor as before, the cold trip point moves down to -5C, and the hot trip point moves down to 34C. If a Vishay Curve 1 thermistor with B25/85 = 3950 and resistance of 100k at 25C is used, a 1% RBIAS resistor of 118k and a 1% RADJ resistor of 12.1k results in a cold trip point of 0C, and a hot trip point of 39C. End-Of-Charge Indication and Safety Timeout The LTC4120 uses a safety timer to terminate charging. Whenever the LTC4120 is in constant current mode the timer is paused, and if FB transitions through the VRCHG threshold the timer is reset. When the battery voltage reaches the float voltage, a safety timer begins counting down a 2-hour timeout. If charge current falls below one-tenth of the programmed maximum charge current (hC/10), the CHRG status pin rises, but top-off charge current continues to flow until the timer finishes. After the timeout, the LTC4120 enters a low power sleep mode. Li-Ion 4120 F07 2% INTVCC increases to 285% of the RBIAS resistor as the temperature drops. For a Vishay Curve 2 thermistor with B25/85 = 3490 and 25C resistance of 10k, this corresponds to a temperature of about 0C. The LTC4120 also pauses charging if the thermistor resistance decreases to 57.5% of the RBIAS resistor. For the same Vishay Curve 2 thermistor, this corresponds to approximately 40C. With a Vishay Curve 2 thermistor, the hot and cold comparators both have about 2C of hysteresis to prevent oscillations about the trip points. Automatic Recharge In sleep mode, the IC continues to monitor battery voltage. If the battery falls 2.2% (VRCHG or VRCHG_42) from the Figure 7. NTC Connections 16 Rev. G For more information www.analog.com LTC4120/LTC4120-4.2 OPERATION full-charge float voltage, the LTC4120 engages an automatic recharge cycle. Automatic recharge has a built-in filter of about 0.5ms to prevent triggering a new charge cycle if a load transient causes the battery voltage to drop temporarily. State of Charge and Fault Status Pins The LTC4120 contains two open-drain outputs which provide charge status and signal fault indications. The binary-coded CHRG pin pulls low to indicate charging at a rate higher than C/10. The FAULT pin pulls low to indicate a bad battery timeout, or to indicate an NTC thermal fault condition. During NTC faults the CHRG pin remains low, but when a bad battery timeout occurs the CHRG pin deasserts. When the open-drain outputs are pulled up with a resistor, Table 3 summarizes the charger state that is indicated by the pin voltages. Table 3. LTC4120 Open-Drain Indicator Outputs with Resistor Pull-Ups FAULT CHRG CHARGER STATE High High Off or Topping Off Charging at a Rate Less Than C/10 High Low Charging at Rate Higher Than C/10 Low High Bad Battery Fault Low Low NTC Thermal Fault Charging Paused Low Battery Voltage Operation The LTC4120 automatically preconditions heavily discharged batteries. If the battery voltage is below VLOWBAT minus its hysteresis (typically 2.05V--e.g., battery pack protection has been engaged) a DC current, ILOWBAT, is applied to the BAT pin from the INTVCC supply. When the battery voltage rises above VLOWBAT, the switching regulator is enabled and charges the battery at a trickle charge level of 10% of the full-scale charge current (in addition to the DC ILOWBAT current). Trickle charging of the battery continues until the sensed battery voltage (sensed via the feedback pin for the LTC4120) rises above the trickle charge threshold, VTRKL. When the battery rises above the trickle charge threshold, the full-scale charge current is applied and the DC trickle charge current is turned off. If the battery remains below the trickle charge threshold for more than 30 minutes, charging terminates and the fault status pin is asserted to indicate a bad battery. After a bad battery fault, the LTC4120 automatically restarts a new charge cycle once the failed battery is removed and replaced with another battery. The LTC41204.2 monitors the BATSNS pin voltage to sense LOWBAT and TRKL conditions. Precision Run/Shutdown Control The LTC4120 remains in a low power disabled mode until the RUN pin is driven above VEN (typically 2.45V). While the LTC4120 is in disabled mode, current drain from the battery is reduced to extend battery lifetime, the status pins are both de-asserted, and the FBG pin is high impedance. Charging can be stopped at any time by pulling the RUN pin below 2.25V. The LTC4120 also offers an extremely low operating current shutdown mode when the RUN pin is pulled below VSD (typically 0.7V). In this condition less than 20A is drawn from the supply at IN. Differential Undervoltage Lockout The LTC4120 monitors the difference between the battery voltage, VBAT, and the input supply, VIN. If the difference (VIN-VBAT) falls to VDUVLO, all functions are disabled and the part is forced into shutdown mode until (VINVBAT) rises above the VDUVLO hysteresis. The LTC41204.2 monitors the BATSNS and IN pin voltages to sense DUVLO condition. User Selectable Buck Operating Frequency The LTC4120 uses a constant-frequency synchronous step-down buck architecture to produce high operating efficiency. The nominal operating frequency of the buck, fOSC, is programmed by connecting the FREQ pin to either INTVCC or to GND to obtain a switching frequency of 1.5MHz or 750kHz, respectively. The high operating frequency allows the use of smaller external components. Selection of the operating frequency is a trade-off between efficiency, component size, and margin from the minimum on-time of the switcher. Operation at lower frequency Rev. G For more information www.analog.com 17 LTC4120/LTC4120-4.2 OPERATION improves efficiency by reducing internal gate charge and switching losses, but requires larger inductance values to maintain low output ripple. Operation at higher frequency allows the use of smaller components, but may require sufficient margin from the minimum on-time at the lowest duty cycle if fixed-frequency switching is required. PWM Dropout Detector If the input voltage approaches the battery voltage, the LTC4120 may require duty cycles approaching 100%. This mode of operation is known as dropout. In dropout, the operating frequency may fall well below the programmed fOSC value. If the top switch remains on for eight clock cycles, the dropout detector activates and forces the bottom switch on for the remainder of that clock cycle or until the inductor current decays to zero. This avoids a potential source of audible noise when using ceramic input or output capacitors and prevents the boost supply capacitor for the top gate drive from discharging. In dropout operation, the actual charge current may not be able to reach the full-scale programmed value. In such a scenario the analog charge current monitor function does not represent actual charge current being delivered. Burst Mode Operation At low charge currents, for example during constantvoltage mode, the LTC4120 automatically enters Burst Mode operation. In Burst Mode operation the switcher is periodically forced into standby mode in order to improve efficiency. The LTC4120 automatically enters Burst Mode operation after it exits constant-current (CC) mode and as the charge current drops below about 80mA. Burst Mode operation is triggered at lower currents for larger PROG resistors, and depends on the input supply voltage. Refer to graph Burst Mode Trigger Current and graph Typical Burst Mode Waveform, in the Typical Performance Characteristics, for more information on Burst Mode operation. Burst Mode operation has some hysteresis and remains engaged for battery currents up to about 150mA. 18 While in Burst Mode operation, the PROG pin voltage to average charge current relationship is not well defined. This is due to the PROG pin voltage falling to 0V in between bursts, as shown in G14. If the PROG pin voltage falls below 120mV for longer than 350s this causes the CHRG pin to de-assert, indicating C/10. Burst current ripple depends on the selected switch inductor, and VIN/ VBAT. BOOST Supply Refresh The BOOST supply for the top gate drive in the LTC4120 switching regulator is generated by bootstrapping the BOOST flying capacitor to INTVCC whenever the bottom switch is turned on. This technique provides a voltage of INTVCC from the BOOST pin to the SW pin. In the event that the bottom switch remains off for a prolonged period of time, e.g., during Burst Mode operation, the BOOST supply may require a refresh. Similar to the PWM dropout timer, the LTC4120 counts the number of clock cycles since the last BOOST refresh. When this count reaches 32, the next PWM cycle begins by turning on the bottom side switch first. This pulse refreshes the BOOST flying capacitor to INTVCC and ensures that the topside gate driver has sufficient voltage to turn on the topside switch at the beginning of the next cycle. Operation Without an Input Supply or Wireless Power When a battery is the only available power source, care should be taken to eliminate loading of the IN pin. Load current on IN drains the battery through the body diode of the top side power switch as VIN falls below VSW. To prevent this possibility, place a diode between the input supply and the IN capacitor, CIN. The rectification diode (D9 in Figure 5 and Figure 11) in the wireless power applications also eliminates this discharge path. Alternately, a P-channel MOSFET may be placed in series with the BAT pin provided care is taken to directly sense the positive battery terminal voltage with FB via the battery resistive divider. This is illustrated in Figure 15. Rev. G For more information www.analog.com LTC4120/LTC4120-4.2 APPLICATIONS INFORMATION 0.50 LX LR 1:n COUPLING COEFFICIENT (k) IR IAC VR 4120 F08 Figure 8. Wireless Power Transfer Wireless Power Transfer In a wireless power transfer system, power is transmitted using alternating magnetic fields. Power is transferred based on the principle that an AC current in a transmitter coil produces an AC current in a receiver coil that is placed in the magnetic field generated by the transmitter coil. The magnetic field coupling is described by the mutual inductance, M. This term does not have a physical representation but is referred to using the unit-less terms k and n. Where k is the coupling coefficient: k= M L X * LR n n= R = nX LR LX The turns ratio is proportional to the square root of the ratio of receiver coil inductance to transmitter coil inductance. In the wireless power transfer system an AC current, IAC, applied to the transmit coil LX, produces an AC current in the receive coil, LR of: IR(AC) = 2 * * M * IAC = 2 * * k * LX * LR * IAC The coupling coefficient is a variable that depends on the orientation and proximity of the transmitter coil relative to the receiver coil. If the two coils are in a transformer, then k = 1. If the two coils are completely isolated from each other then k = 0. In a typical LTC4120-based wireless power design, k varies from around 0.18 at 10mm spacing, to about 0.37 with the coils at 3mm spacing. This is illustrated in Figure 9. With low resistance in the LX and LR coils, the efficiency is inherently high, even at low coupling ratios. The transmitter in Figures 4 and 10 generates a sine wave at the resonant frequency, fO, across the transmitter coil and X 0.40 X + 0.35 X +X +X 0.30 X 5mm MISALIGNMENT X 10mm MISALIGNMENT +X X 0.25 X 0.20 +X +X X X 0.15 0.10 0 1 2 3 4 5 6 7 COIL DISTANCE (mm) 8 9 10 4120 F09 Figure 9. Coupling Coefficient k vs Distance capacitor (LX||CX). With a peak-to-peak amplitude that is proportional to the applied input voltage: VAC 2 * * VDC This generates a sinusoidal current in the transmit coil with peak-to-peak amplitude: IAC = And n is the turns ratio--the number of turns in the receiver coil divided by the number of turns in the transmitter coil: + NO MISALIGNMENT 0.45 VAC 2 * * fO * L X VDC fO * L X The AC voltage induced at the receive coil is a function of both the applied voltage, the coupling, as well as the impedance at the receiver. With no load at the receiver, the open-circuit voltage, VIN(OC), is approximately: VIN(OC) k * n * 2 * * VDC The receiver (shown in Figures 5 and 10) uses a resonant tuned circuit followed by a rectifier to convert the induced AC voltage into a DC voltage to power the LTC4120 and charge a battery. Power delivered to the LTC4120 depends on the impedance of the LTC4120 and the impedance of the tuned circuit at the resonant frequency of the transmitter. The LTC4120 employs a proprietary circuit, called dynamic harmonization control (DHC) that modulates the impedance of the receiver depending on the voltage at the input to the LTC4120. This technique ensures that over a wide range of coupling coefficients the induced rectified voltage does not exceed voltage compliance ratings when the load goes away (e.g, when the battery is fully charged). DHC efficiently adjusts the receiver impedance depending on the load without compromising available power. In the event that the coupling may become too large (e.g. receiver coil is placed too close to the transmitter coil) then it is recommended to place a Zener diode across the Rev. G For more information www.analog.com 19 LTC4120/LTC4120-4.2 APPLICATIONS INFORMATION input to the LTC4120 to prevent exceeding the absolute maximum rating of the LTC4120. Diode D6 (in Figure 4 and Figure 10) illustrates this connection. of a 39V Zener diode (D6 in Figures 4 and 10) at the input to the LTC4120 will prevent overvoltage conditions from damaging the LTC4120. The RMS voltage at the rectifier output depends on the load of the LTC4120, i.e., the charge current, as well as the applied AC current, IAC. The applied AC current depends both on the components of the tuned network as well as the applied DC voltage. The load at the receiver depends on the state of charge of the battery. If the coupling and/or the applied AC current is not well controlled, the addition Resonant Transmitter and Receiver VCC 4.75V TO 5.25V LB1 68H An example DC/AC transmitter is shown in Figure 10. A 5V 5% supply to the transmitter efficiently produces a circulating AC current in LX, which is coupled to LR. For higher voltage inputs, a pre-regulator DC/DC converter can be used to generate 5V (see Figure 11). Power is transmitted from transmitter to receiver at the resonant TRANSMITTER RECEIVER C2S2 LB2 68H D1 LX CX 0.3F 5H C4 0.01F LR C2S1 C2P1 D2 D3 C5 0.01F DHC IN BOOST SW R1 100 R2 100 D2 D3 M1 U1 LTC4120 C2P2 C4 2.2F M2 INTVCC C5 10F D4 39V OPT C1 10F C2 47F C3 L1 CHGSNS BAT + FB D1 D4 GND FBG 4120 F10 Figure 10. DC/AC Converter, Transmit/Receive Coils, Tuned Series Resonant Receiver and AC/DC Rectifier HVIN 8V TO 38V GND C6 4.7F VIN BD BOOST R3 150k C7 0.068F R4 40.2k RUN/SS SW U1 LT3480 SYNC RT FB GND PG VC C9 0.47F L3 4.7F D5 DFLS240L R5 20k C8 330pF C10 22F R8 150k M3 Si2333DS M4 2N7002L R10 100k VCC 5V CONNECT TO Tx VCC R7 536k R6 100k 4120 F11 Figure 11. High Voltage Pre-Regulator for Transmitter 20 Rev. G For more information www.analog.com LTC4120/LTC4120-4.2 APPLICATIONS INFORMATION frequency, fO; which depends on both component values as well as the load at the receiver. The tolerance of the components selected in both the transmitter and receiver circuits is critical to achieving maximum power transfer. The voltages across the receiver components may reach 40V, so adequate voltage ratings must also be observed. Resonant Converter Component Selection It is recommended to use the components listed in Table 4 and Table 5 for the resonant transmitter and receiver respectively. Figure 12 illustrates the PCB layout of the embedded receiver coil. Figure 13 and Figure 14 show the finished transmitter and receiver. The 25mm ferrite bead Table 4. Recommended Transmitter and High Voltage Pre-Regulator Components Transmitter Components ITEM DESCRIPTION MANUFACTURER/PART NUMBER D2, D3 DIODE, SCHOTTKY, 40V, 2A ON SEMI NSR10F40NXT5G D1, D4 DIODE, ZENER, 16V, 350mW, SOT23 DIODES BZX84C16 M1, M2 MOSFET, SMT, N-CHANNEL, 60V, 11m, S08 VISHAY Si4470EY-T1GE3 IND, SMT, 68H, 0.41A, 0.4, 20% TDK VLCF5028T-680MR40-2 LB1, LB2 C4, C5 CAP, CHIP, X7R, 0.01F, 10%, 50V, 0402 MURATA GRM155R71H103KA88D R1, R2 RES, CHIP, 100, 5%, 1/16W, 0402 VISHAY CRCW0402100RJNED CAP, CHIP, PPS, 0.15F, 2%, 50V PANASONIC ECHU1H154GX9 CX1, 2 CAP, CHIP, PPS, 0.1F, 2%, 50V PANASONIC ECHU1H104GX9 CAP, CHIP, PPS, 0.033F, 2%, 50V PANASONIC ECHU1H333GX9 CAP, PPS, 0.15F, 2.5%, 63VAC, MKS02 WIMA MKS0D031500D00JSSD CX (Opt) WIMA MKS0D03100 CAP, PPS, 0.10F, 2.5%, 63VAC, MKS02 CAP, PPS, 0.033F, 2.5%, 63VAC, MKS02 WIMA MKS0D03033 5.0H TRANSMIT COIL TDK WT-505060-8K2-LT LX or 6.3H TRANSMIT COIL TDK WT-505090-10K2-A11-G or 6.3H TRANSMIT COIL WURTH 760308111 or 5.0H TRANSMIT COIL INTER-TECHNICAL L41200T02 High Voltage Pre-Regulator Components U1 LT3480EDD, PMIC 38V, 2A, 2.4MHz Step-Down Switching LINEAR TECH LT3480EDD Regulator with 70A Quiescent Current M3 MOSFET, SMT, P-CHANNEL, -12V, 32m, SOT23 VISHAY Si2333DS M4 MOSFET, SMT, N-CHANNEL, 60V, 7.5, 115mA, SOT23 ON SEMI 2N7002L D5 DIODE, SCHOTTKY, 40V, 2A, POWERDI123 DIODES DFLS240L L3 IND, SMT, 4.7H, 1.6A, 0.125, 20% COILCRAFT LPS4018-472M C6 CAP, CHIP, X5R, 4.7F, 10%, 50V, 1206 MURATA GRM155R71H4755KA12L C7 CAP, CHIP, X5R, 4.7F, 10%, 50V, 0603 MURATA GRM188R71H683K C8 CAP, CHIP, COG, 330pF, 5%, 50V, 0402 TDK C1005COG1H331J C9 CAP, CHIP, X7R, 0.47F, 10%, 25V, 0603 MURATA GRM188R71E474K C10 CAP, CHIP, X5R, 22F, 20%, 6.3V, 0805 TAIYO-YUDEN JMK212BJ226MG R3, R8 RES, CHIP, 150k, 5%, 1/16W, 0402 VISHAY CRCW0402150JNED R4 RES, CHIP, 40.2k, 1%, 1/16W, 0402 VISHAY CRCW040240K2FKED R5 RES, CHIP, 20k, 1%, 1/16W, 0402 VISHAY CRCW040220K0FKED R6, R10 RES, CHIP, 100k, 1%, 1/16W, 0402 VISHAY CRCW0402100KFKED R7 RES, CHIP, 536k, 1%, 1/16W, 0402 VISHAY CRCW0402536KFKED 1C = 300nF with 5H L coil, or C = 233nF with 6.3H L coil. X X X X 2Pay careful attention to assembly guidelines when using ECHU capacitors, as the capacitance value may shift if the capacitor is over heated while soldering. Plastic film capacitors such as Panasonic ECHU series or Metallized Polypropylene capacitors such as WIMA MKP as suitable for the transmitter Rev. G For more information www.analog.com 21 LTC4120/LTC4120-4.2 APPLICATIONS INFORMATION Table 5. Recommended Receiver Components ITEM D1, D2, D3 D4 (Opt) LR DESCRIPTION DIODE, SCHOTTKY, 40V, 2A, POWERDI123 DIODE, ZENER, 39V, 5%, 1W, POWERDI123 IND, EMBEDDED, 47H, 43 TURNS WITH 25mm FERRITE BEAD L1 C2P1 C2P2 C2S1 C2S2 C1 C2 C3 C4 U1 or 47H RECEIVER COIL or 47H RECEIVER COIL or 48H RECEIVER COIL IND, SMT, 15H, 260m, 20%, 0.86A, 4mm x 4mm CAP, CHIP, COG, 0.0047F, 5%, 50V, 0805 CAP, CHIP, COG, 0.00018F, 5%, 50V, 0603 CAP, CHIP, COG, 0.022F, 5%, 50V, 0805 CAP, CHIP, COG, 0.0047F, 5%, 50V, 0805 CAP, CHIP, X5R, 10F, 20%, 16V, 0805 CAP, CHIP, X5R, 47F, 10%, 16V, 1210 CAP, CHIP, X7R, 0.01F, 20%, 6.3V. 0402 CAP, CHIP, X5R, 10F, 20%, 16V, 0805 400mA WIRELESS SYNCHRONOUS BUCK BATTERY CHARGER MANUFACTURER/PART NUMBER DIODES DFLS240L DIODES DFLZ39 EMBEDDED 4-LAYER PCB (see Figure 12) ADAMS MAGNETICS B67410-A0223-X195 TDK WR282840-37K2-LR3 WURTH 760308101303 INTER-TECHNICAL L41200R02 COILCRAFT LPS4018-153ML MURATA GRM21B5C1H472JA01L KEMET C0603C182J5GAC7533 MURATA GRM21B5C1H223JA01L MURATA GRM21B5C1H472JA01L TDK C2012X5R1C106K MURATA GRM32ER61C476KE15L TDK C1608X7R1H103K TDK C2012X5R1C106K LINEAR TECH LTC4120 LAYER STRUCTURE L1 - TOP SIDE L2 L3 L4 - BOTTOM SIDE FINISHED THICKNESS TO BE 0.031" 0.005" TOTAL OF 4 LAYERS WITH 2oz CU ON THE OUTER LAYERS AND 2oz CU ON THE INNER LAYERS TOP METAL 2nd METAL 3rd METAL BOTTOM METAL 4120 F12 Figure 12. 4-Layer PCB Layout of Rx Coil 22 Rev. G For more information www.analog.com LTC4120/LTC4120-4.2 APPLICATIONS INFORMATION Figure 13. Tx Layout: Demo Circuit 1968A in Figure 14 covers the embedded receiver coil described in Figure 12. Gerber layout files for both the transmitter and receiver boards are available at the following link: Figure 14. Rx Layout with Ferrite Shield: Demo Circuit 1967A-B LTC4120 Evaluation Kits Alternative component values can be chosen by following the design procedure outlined below. Resonant Transmitter Tuning: LX, CX The basic transmitter (shown in Figure 4) has a resonant frequency, fO, that is determined by components LX, and CX. The selection of LX and CX are coupled so as to obtain the correct operating frequency. The selection of LX and LR is also coupled to ideally obtain a turns ratio of 1:3. Having selected a transmitter inductor, LX, the transmitter capacitor should be selected to obtain a resonant frequency of 130kHz. Due to limited selection of standard values, several standard value capacitors may need to be used in parallel to obtain the correct value for fO: fO 1 2 * * L X * CX = 130 kHz The transmitter inductor and capacitor, LX and CX, support a large circulating current. Series resistance in the inductor is a source of loss and should be kept to a minimum for optimal efficiency. Likewise the transmitter capacitor(s), CX, must support large ripple currents and must be selected with adequate voltage rating and low dissipation factors. Resonant Receiver Tuning: LR, C2S, C2P The tuned circuit resonance of the receiver, fT, is determined by the selection of LR and C2S + C2P. Select the capacitors to obtain a resonant frequency 1% to 3% below fO: fT 1 2 * * L R * ( C2P + C2S ) As in the case of the transmitter, multiple parallel capacitors may need to be used to obtain the optimum value. Finally, select the detuned resonance, fD to be about 5% to 15% higher than the tuned resonance, keeping the value of C2P below 30nF to limit power dissipation in the DHC pin: fD 1 2 * * L R * C2S Alternative Transmitter Options The resonant DC/AC transmitter discussed in the previous section is a basic and inexpensive to build transmitter. However, this basic transmitter requires a relatively precise DC input voltage to meet a given set of receive power requirements. It is unable to prevent power transmission to foreign metal objects--and can therefore cause these objects to heat up. Furthermore, Rev. G For more information www.analog.com 23 LTC4120/LTC4120-4.2 APPLICATIONS INFORMATION the operating frequency of the basic transmitter can vary with component selection. LTC4120 customers can also choose more advanced transmitter options such as the LTC4125. With additional features such as: foreign metal detection; optimum power search and AutoResonantTM operating frequency. For more information on advanced transmitter options refer to the Wireless Power Users Guide. Maximum Battery Power Considerations Using one of the approved transmitter options with this wireless power design provides a maximum of 2W at the input to the LTC4120. It is optimized for supplying 400mA of charge current to a 4.2V Li-Ion battery. If a higher battery voltage is selected, then a lower charge current must be used as the maximum power available is limited. The maximum battery charge current, ICHG(MAX), that may be programmed for a given float voltage, VFLOAT, can be calculated based on the charger efficiency, EFF, as: When operating from a high input voltage with a low battery voltage, the PWM control algorithm may attempt to enforce a duty cycle which requires an on-time lower than the LTC4120 minimum, tMIN(ON). This minimum duty cycle is approximately 18% for 1.5MHz operation or 9% for 750kHz operation. Typical minimum on-time is illustrated in graph G11 in the Typical Performance Characteristics section. If the on-time is driven below tMIN(ON), the charge current and battery voltage remain in regulation, but the switching duty cycle may not remain fixed, and/or the switching frequency may decrease to an integer fraction of its programmed value. The maximum input voltage allowed to maintain constant frequency operation is: VIN(MAX) = VLOWBAT fOSC * tMIN(ON) where VLOWBAT, is the lowest battery voltage where the switcher is enabled. The charger efficiency, EFF, depends on the operating conditions and may be estimated using the Buck Efficiency curve in the Typical Performance Characteristics. Do not select a charge current greater than this limit when selecting RPROG. Exceeding the minimum on-time constraint does not affect charge current or battery float voltage, so it may not be of critical importance in most cases and high switching frequencies may be used in the design without any fear of severe consequences. As the sections on Inductor Selection and Capacitor Selection show, high switching frequencies allow the use of smaller board components, thus reducing the footprint of the applications circuit. Input Voltage and Minimum On-Time Fixed-frequency operation may also be influenced by dropout and Burst Mode operation as discussed previously. * 2W ICHG(MAX) EFF VFLOAT The LTC4120 can operate from input voltages up to 40V. The LTC4120 maintains constant frequency operation under most operating conditions. Under certain situations with high input voltage and high switching frequency selected and a low battery voltage, the LTC4120 may not be able to maintain constant frequency operation. These factors, combined with the minimum on-time of the LTC4120, impose a minimum limit on the duty cycle to maintain fixed-frequency operation. The on-time of the top switch is related to the duty cycle (VBAT/VIN) and the switching frequency, fOSC in Hz: tON = 24 VBAT fOSC * VIN Switching Inductor Selection: LSW The primary criterion for switching inductor value selection in an LTC4120 charger is the ripple current created in that inductor. Once the inductance value is determined, the saturation current rating for that inductor must be equal to or exceed the maximum peak current in the inductor, IL(PEAK). The peak value of the inductor current is the sum of the programmed charge current, ICHG, plus one-half of the ripple current, IL. The peak inductor current must also remain below the current limit of the LTC4120, IPEAK: IL(PEAK) = ICHG + IL 2 < IPEAK Rev. G For more information www.analog.com LTC4120/LTC4120-4.2 APPLICATIONS INFORMATION The current limit of the LTC4120, IPEAK, is at least 585mA (and at most 1250mA). The typical value of IPEAK is illustrated in graph RSNS Current Limit vs Temperature, in the Typical Performance Characteristics. For a given input and battery voltage, the inductor value and switching frequency determines the peak-to-peak ripple current amplitude according to the following formula: IL = ( VIN - VBAT ) * VBAT fOSC * VIN * L SW Ripple current is typically set to be within a range of 20% to 40% of the programmed charge current, ICHG. To obtain a ripple current in this range, select an inductor value using the nearest standard inductance value available that obeys the following formula: L SW ( VIN(MAX) - VFLOAT ) * VFLOAT fOSC * VIN(MAX) * ( 30% * ICHG ) Then select an inductor with a saturation current rating at a value greater than IL(PEAK). Input Capacitor: CIN The LTC4120 charger is biased directly from the input supply at the VIN pin. This supply provides large switched currents, so a high quality, low ESR decoupling capacitor is recommended to minimize voltage glitches at VIN. VIN VIN CHRG BST 10F RUN LTC4120 2.2F SW CHGSNS BAT Bulk capacitance is a function of the desired input ripple voltage (VIN), and follows the relation: CIN(BULK) = VIN (F ) Input ripple voltages (VIN) above 10mV are not recommended. 10F is typically adequate for most charger applications, with a voltage rating of 40V. Reverse Blocking When a fully charged battery is suddenly applied to the BAT pin, a large in-rush current charges the CIN capacitor through the body diode of the LTC4120 topside power switch. While the amplitude of this current can exceed several Amps, the LTC4120 will survive provided the battery voltage is below the maximum value of 11V. To completely eliminate this current, a blocking P-channel MOSFET can be placed in series with the BAT pin. When the battery is the only source of power, this PFET also serves to decrease battery drain current due to any load placed at VIN. As shown in Figure 15, the PFET body diode serves as the blocking component since CHRG is high impedance when the battery voltage is greater than the input voltage. When CHRG pulls low, i.e. during most of a normal charge cycle, the PFET is on to reduce power dissipation. This PFET requires a forward current rating equal to the programmed charge current and a reverse breakdown voltage equal to the programmed float voltage. Figure 15 illustrates how to add a blocking PFET connected with the LTC4120. 4.99k* 22nF LSW 49.9k 4.7F INTVCC V ICHG BAT VIN 470k 22F SI2343DS + Li-Ion RFB1 PROG FB RFB2 RPROG GND FBG 4120 F15 *ADD 4.99k WHEN MAX BAT VOLTAGE APPROACHES 85% OF VGS LIMIT FOR Si2343. Figure 15. Reverse Blocking with a P-Channel MOSFET in Series with the BAT Pin Rev. G For more information www.analog.com 25 LTC4120/LTC4120-4.2 APPLICATIONS INFORMATION BAT Capacitor and Output Ripple: CBAT Calculating Power Dissipation The LTC4120 charger output requires bypass capacitance connected from BAT to GND (CBAT). A 22F ceramic capacitor is required for all applications. In systems where the battery can be disconnected from the charger output, additional bypass capacitance may be desired. In this type of application, excessive ripple and/or low amplitude oscillations can occur without additional output bulk capacitance. For optimum stability, the additional bulk capacitance should also have a small amount of ESR. For these applications, place a 100F low ESR non-ceramic capacitor (chip tantalum or organic semiconductor capacitors such as Sanyo OS-CONs or POSCAPs) from BAT to GND, in parallel with the 22F ceramic bypass capacitor, or use large ceramic capacitors with an additional series ESR resistor of less than 1. This additional bypass capacitance may also be required in systems where the battery is connected to the charger with long wires. The voltage rating of all capacitors applied to CBAT must meet or exceed the battery float voltage. The user should ensure that the maximum rated junction temperature is not exceeded under all operating conditions. The thermal resistance of the LTC4120 package (JA) is 54C/W; provided that the exposed pad is soldered to sufficient PCB copper area. The actual thermal resistance in the application may depend on forced air cooling or other heat sinking means, and especially the amount of copper on the PCB to which the LTC4120 is attached. The actual power dissipation while charging is approximated by the following formula: Boost Supply Capacitor: CBST The BOOST pin provides a bootstrapped supply rail that provides power to the top gate drivers. The operating voltage of the BOOST pin is internally generated from INTVCC whenever the SW pin pulls low. This provides a floating voltage of INTVCC above SW that is held by a capacitor tied from BOOST to SW. A low ESR ceramic capacitor of 10nF to 22nF is sufficient for CBST, with a voltage rating of 6V. INTVCC Supply and Capacitor: CINTVCC Power for the top and bottom gate drivers and most other internal circuitry is derived from the INTVCC pin. A low ESR ceramic capacitor of 2.2F is required on the INTVCC pin. The INTVCC supply has a relatively low current limit (about 20mA) that is dialed back when INTVCC is low to reduce power dissipation. Do not use the INTVCC voltage to supply power for any external circuitry apart from the NTCBIAS network. When the RUN pin is above VEN the INTVCC supply is enabled, and when INTVCC rises above UVINTVCC the charger is enabled. 26 PD ( VIN - VBAT ) * ITRKL + VIN * IIN(SWITCHING) +R SNS * ICHG2 V +RDS(ON)(TOP) * BAT * ICHG2 VIN V +RDS(ON)(BOT) * 1- BAT * ICHG2 VIN During trickle charge (VBAT < VTRKL) the power dissipation may be significant as ITRKL is typically 10mA, however during normal charging the ITRKL term is zero. The junction temperature can be estimated using the following formula: TJ = TA + PD * JA where TA is the ambient operating temperature. Significant power is also consumed in the transmitter electronics. The large AC voltage generated across the LX and CX tank results in power being dissipated in the DC resistance of the LX coil and the ESR of the CX capacitor. The large induced magnetic field in the LX coil may also induce heating in nearby metallic objects. PCB Layout To prevent magnetic and electrical field radiation and high frequency resonant problems, proper layout of the components connected to the LTC4120 is essential. For maximum efficiency, the switch node rise and fall times Rev. G For more information www.analog.com LTC4120/LTC4120-4.2 APPLICATIONS INFORMATION should be minimized. The following PCB design priority list will help insure proper topology. Layout the PCB using the guidelines listed below in this specific order. 1. Keep foreign metallic objects away from the transmitter coil. Metallic objects in proximity to the transmit coil will suffer from induction heating and will be a source of power loss. With the exception of a ferrite shield that can be used to improve the coupling from transmitter coil to receiver coil when placed behind the transmitter coil. Advanced transmitters using LTC4125 include features to detect the presence of foreign metallic objects that mitigates this issue. 2. VIN input capacitor should be placed as close as possible to the IN and GND pins, with the shortest copper traces possible and a via connection to the GND plane 3. Place the switching inductor as close as possible to the SW pin. Minimize the surface area of the SW pin node. Make the trace width the minimum needed to support the programmed charge current, and ensure that the spacing to other copper traces be maximized to reduce capacitance from the SW node to any other node. 4. Place the BAT capacitor adjacent to the BAT pin and ensure that the ground return feeds to the same copper that connects to the input capacitor ground before connecting back to system ground. 5. Route analog ground (RUN ground and INTVCC capacitor ground) as a separate trace back to the LTC4120 GND pin before connecting to any other ground. 6. Place the INTVCC capacitor as close as possible to the INTVCC pin with a via connection to the GND plane. 9. Minimize capacitive coupling to GND from the FB pin. 10. Maximize the copper area connected to the exposed pad. Place via connections directly under the exposed pad to connect a large copper ground plane to the LTC4120 to improve heat transfer. Design Examples The design example illustrated in Figure 17, reviews the design of the resonant coupled power transfer charger application. First the design of the wireless power receiver circuit is described. Then consider the design for the charger function given the maximum input voltage, a battery float voltage of 8.2V, and a charge current of 200mA for the LTC4120. This example also demonstrates how to select the switching inductance value to avoid discontinuous conduction; where switching noise increases. The wireless power receiver is formed by the tuned network LR and C2P, C2S. This tuned network automatically modulates the resonance of the tank with the DHC pin of the LTC4120 to optimize power transfer. The resonant frequency of the tank should match the oscillation frequency of the transmitter. Given the transmitter shown in Figure 4 this frequency is 130kHz. The tuned receiver resonant frequency is: fT = 1 2 * * LR * (C2P + C2S) = 127 kHz In this design example, the de-tuned resonant frequency is: fD = 1 2 * * LR * C2S = 142kHz 7. Route the DHC trace with sufficient copper and vias to support 350mA of RMS current, and ensure that the spacing from the DHC node to other copper traces be maximized to reduce capacitance and radiated EMI from the DHC node to other sensitive nodes. fD should be set between 5% and 15% higher than fT. A higher level gives more control range but results in more power dissipation. 8. It is important to minimize parasitic capacitance on the PROG pin. The trace connecting to this pin should be as short as possible with extra wide spacing from adjacent copper traces. Now C2S can be calculated to be 26.7nF. Two standard parallel 50V rated capacitors, 22nF and 4.7nF, provide a value within 1% of the calculated C2S. Now C2P can be calculated to be 6.5nF which can be obtained with A 47H coil is selected for LR to obtain a turns ratio of 3:1 from the transmitter coil, LX = 5H. Rev. G For more information www.analog.com 27 LTC4120/LTC4120-4.2 APPLICATIONS INFORMATION 4.7nF and 1.8nF capacitors in parallel. All of the capacitors should be selected with 5% or better tolerance. The rectifier, D8, D9 and D5 are selected as 50V rated Schottky diodes. Now consider the design circuit for the LTC4120 charger function. First, the external feedback divider, RFB1/RFB2, is found using standard 1% values: RFB1 = 8.2V * 588k 2.00M 2.4V 2.00M * 588k 825k RFB2 = 2.00M - 588k With an 8.2V float voltage the maximum charge current available is limited by the maximum power available from the RCPT at EFF = 85% charger efficiency: ICHG(MAX) 8.2V = 207mA A charge current of 200mA is achieved by selecting a standard 1% RPROG resistor of: RPROG = hPROG * VPROG ICHG = 6.04k 5V 1.5MHz * 17V The maximum loaded input voltage is used to select the operating frequency and influences the value of the switching inductor. The saturation current rating of the switching inductor is selected based on the worst case conditions at the maximum open-circuit voltage. A typical 2-cell Li-Ion battery pack engages pack protection for VBAT less than 5V, this is the lowest voltage = 476ns > tMIN(ON) Now the switching inductor value is calculated. The inductor value is calculated based on achieving a 30% ripple current. The ripple current is calculated at the typical input operating voltage of 17V: ( 17V - 8.2V ) * 8.2V = 48H 1.5MHz * 17V * ( 30% * 200mA ) 56H is the next standard inductor value that is greater than this minimum. This inductor value results in a worst-case ripple current at the input open-circuit voltage, VIN(OC). VIN(OC) is estimated based on the transmitter design in Figure 4, at the largest coupling coefficient k = 0.37 as: VIN(OC) = k * n * * VIN(TX) VIN(OC) = 0.37 * 3 * 3.14 * 5V = 34.9V IL = ( 34.9V - 8.2V ) * 8.2V 1.5MHz * 56H * 34.9V = 75mA This results in a worst-case peak inductor current of: IL(PEAK) = ICHG + While charging a battery, the resonant receiver is loaded by the charge current, this load reduces the input voltage from the open-circuit value to a typical voltage in a range from 12V (at UVCL) up to about 26V. The amplitude of this voltage depends primarily on the amount of coupling between the transmitter and the receiver, typically this voltage is about 17V. 28 tON = L3 > With these resistors, and including the resistance of the FBG pin, the battery float voltage is 8.212V. 85% * 2W considered for determining the on-time and selecting the 1.5MHz operating frequency. IL 2 = 237mA Select an inductor with a saturation current rating greater than the worst-case peak inductor current of 237mA. Select a 50V rated capacitor for CIN = 10F to achieve an input voltage ripple of 10mV at the typical operating input voltage of 17V: 8.2V 17V = 10mV 10F 200mA * VIN = And select 6V rated capacitors for CINTVCC = 2.2F, CBOOST = 22nF, and CBAT = 22F. Optionally add diode D6, a 1W, 39V Zener diode if the coupling from transmitter to receiver coils is not well enough controlled to ensure that VIN remains below 39V when the battery is fully charged. Rev. G For more information www.analog.com LTC4120/LTC4120-4.2 APPLICATIONS INFORMATION Finally the RUN pin divider is selected to turn on the charger once the input voltage reaches 11.2V. With R3 = 374k and R4 = 102k the RUN pin reaches 2.4V at VIN = 11.2V. With this RUN pin divider, the LTC4120 is disabled once VIN falls below 10.5V. PD = 20V * 5mA + 0.3* 0.2A 2 For this design example, power dissipation during trickle charge, where the switching charge current is 20mA at VBAT = 3V and IIN switching = 5mA, is calculated as follows: This dissipated power results in a junction temperature rise of 6C over ambient. PD = ( 20V - 3V ) * 10mA + 20V * 5mA +0.3* 0.02A 2 + 0.8* 3V 20V Design Example 2: Operation with the LTC4125 * 0.02A 2 The LTC4125 is a 5W AutoResonant wireless power transmitter that offers several advantages over the simple transmitter shown in Figure 10, including foreign object detection, external overtemperature detection, automatic tuning of switching frequency and transmit power. When operating the LTC4120 receiver with the LTC4125, the DHC pin serves to enable an external shunt regulator that optimizes the input supply voltage to the LTC4120 as shown in Figure 16. For more information on using the LTC4125 see the LTC4125 data sheet. 3V 2 +0.5* 1- * 0.02A 20V = 0.27W This dissipated power results in a junction temperature rise of: PD * JA = 0.27W * 54C/W = 15C During regular charging with VBAT > VTRKL, the power dissipation reduces to: IIN 4.5V TO 5.5V 33nF 20m 8.2V * 0.2A 2 20V 8.2V * 0.2A 2 = 0.14mW +0.5* 1- 20V +0.8* DR1 VIN 1F 100k DSTAT 100k IN DTH 47F x2 STAT IN1 IN2 59.0k 10nF CTX 100nF LTC4125 IN PTH1 100k 100V FB EN IMON 348k CTD CTS 470pF GND 47F 10nF L1 15H CHGSNS DFB DC1 PTH2 QR1 DHC BOOST LTC4120-4.2 VIN 0.1F M1 RC 1k SW SW2 IS+ 10nF 24.9k RUN LRX 47H RNTCTX IS- DC AIR GAP 3mm TO 10mm SW1 PTHM 11.3k LTX 24H NTC FTH 7.87k 10k DFLZ39 10F DR2 2.21k FAULT BAT CHRG BATSNS PROG GND FREQ INTVCC NTC CFB1 0.1F 5.23k 3.01k 10k 2.2F RNTCRX 4.7nF LTX: 760308100110 CTX: C3216C0G2A104J160AC CFB1: GRM188R72A104KA35D DC1: CDBQR70 DSTAT: LTST-C193KGKT-5A DFB: BAS521-7 RNTCTX: NTHS0603N02N1002J RED INDICATES HIGH VOLTAGE PARTS + SINGLE CELL Li-Ion BATTERY PACK DR1, DR2, DR3: DFLS240L DC: BZT52C13 4120 F16 M1: Si7308DN QR1: PMBT3904M RNTCRX: NTHS0402N02N1002F LRX: PCB COIL AND FERRITE: B67410-A0223-X195 OR 760308101303 L1: LPS4018-153ML Figure 16. LTC4125 Driving a 24H Transmit Coil at 103kHz, with 1.3A Input Current Threshold, 119kHz Frequency Limit and 41.5C Transmit Coil Surface Temperature Limit in a Wireless Power System with LTC4120-4.2 as a 400mA Single Cell Li-Ion Battery Charger at the Receiver Rev. G For more information www.analog.com 29 LTC4120/LTC4120-4.2 PACKAGE DESCRIPTION UD Package 16-Lead Plastic QFN (3mm x 3mm) (Reference LTC DWG # 05-08-1691 Rev O) 0.70 0.05 3.50 0.05 1.45 0.05 2.10 0.05 (4 SIDES) PACKAGE OUTLINE 0.25 0.05 0.50 BSC RECOMMENDED SOLDER PAD PITCH AND DIMENSIONS 3.00 0.10 (4 SIDES) BOTTOM VIEW--EXPOSED PAD PIN 1 NOTCH R = 0.20 TYP OR 0.25 x 45 CHAMFER R = 0.115 TYP 0.75 0.05 15 PIN 1 TOP MARK (NOTE 6) 16 0.40 0.10 1 1.45 0.10 (4-SIDES) 2 (UD16) QFN 0904 0.200 REF 0.00 - 0.05 NOTE: 1. DRAWING CONFORMS TO JEDEC PACKAGE OUTLINE MO-220 VARIATION (WEED-2) 2. DRAWING NOT TO SCALE 3. ALL DIMENSIONS ARE IN MILLIMETERS 4. DIMENSIONS OF EXPOSED PAD ON BOTTOM OF PACKAGE DO NOT INCLUDE MOLD FLASH. MOLD FLASH, IF PRESENT, SHALL NOT EXCEED 0.15mm ON ANY SIDE 5. EXPOSED PAD SHALL BE SOLDER PLATED 6. SHADED AREA IS ONLY A REFERENCE FOR PIN 1 LOCATION ON THE TOP AND BOTTOM OF PACKAGE 30 0.25 0.05 0.50 BSC Rev. G For more information www.analog.com LTC4120/LTC4120-4.2 REVISION HISTORY REV DATE DESCRIPTION A 12/13 Updated Table 4 component values and brands. 20 B 03/14 Removed word "battery" from float voltage range bullet. Modified various specification limits and removed some temp dots. Modified frequency range, resistor values and Note 3. Amended IIN curves. Modified text to reflect typical fOSC values. Updated text for VPROG servo. Amended equation for fD. Modified ICHG equation. Changed description of End-Of-Charge indication. Modified typical fOSC values. Modified Resonant Converter Selection. Added high voltage pre-regulator schematic. Added Table 4: Recommended Transmitter and High Voltage Pre-Regulator Components. Added Table 5: Recommended Receiver Components. Added Figure 11, PCB Layout of Rx Coil. Added Figure 12, Tx layout: photo of Demo Circuit 1968A. Added Figure 13, Rx layout: photo of Demo Circuit 1967A-B Modified text of fOSC and fT. Modified fT equation. Modified equation for tON, L3, IL, and IL(PEAK) and changed power dissipation calculations. 1 3 4 7 8 9 14 15 16 17 20 20 20 20 20 20 20 23 28 29 C 05/14 Increased minimum VIN to 12.5V Added fixed 4.2V float version, throughout document, also added electrical parameters for -4.2 Increased IFB specification to TYP 25nA Reduced min RECHG threshold to -38mV Modified VPROG servo voltage spec by +3mV and -3mV Loosened VTRKL threshold voltage spec by -20mV and +10mV Increased TYP VTRKL hysteresis spec to 50mV Changed conditions on ISW specification to IN = Open-Circuit from IN = Float Revised RSNS current limit typical performance characteristics curve Added typical VFLOAT performance characteristics curve Corrected error in IIN(SWITCHING) Current curve (x-axis) Added Block Diagram of -4.2 BATSNS connections Changed VIN labels to IN in Figure 4, 5, and 10 Remove SW inductor selection Tables 6, 7, 8, and 9 Changed location of BAT decoupling cap in Figure 15 with reverse blocking diode Corrected error in L3 equation and substituted correct 56H inductor D 01/15 Change CBAT from 10F to 22F Add Wurth P/N for RX coil Add INTER-TECH P/N for TX and RX coils Remove dos on 68 bias inductor in basic TX schematic for clarity E 05/15 Clarified Battery Charge Current vs Temperature curve Clarified End-of-Charge and Battery Recharge sections Modified Operation without an Input Supply section Enhanced Reverse Blocking section Modified INTVCC Supply and Capacitor section F 02/16 Removed INTVCC spec. Moved Note 4 to UV_INTVCC spec. Modified INTVCC pin definition. Included LTC4125 in Applications Information. Added 4.99k Note. Added paragraph and Figure 16 from LTC4125 data sheet. Renumbered Figure 17. Added to Related Parts Table. G 11/18 Removed references to PowerByProxi. PAGE 1, 3 1 to 32 3 3 3 4 4 4 5 6 8 11 12, 13, 20 N/A 25 28 1, 9, 10, 11, 14, 25, 26, 29 and 32 22 21, 22 12, 20 6 16 18 25,26 26 3 9 24 25 29 32 12, 27 Rev. G Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. Specifications subject to change without notice. No license For is granted implication or otherwise under any patent or patent rights of Analog Devices. more by information www.analog.com 31 LTC4120/LTC4120-4.2 TYPICAL APPLICATION C2S 26.7nF D9 IN D8 D5 CIN 10F D6 OPT 374k C2P 6.5nF 5H FAULT RUN CHGSNS BAT DHC FB 102k Tx CIRCUITRY LX 2k INTVCC FREQ BOOST 2k LTC4120 SW CHRG LR CBST 22nF RFB1 2.00M CINTVCC 2.2F LSW 56H VFLOAT 8.2V CBAT 22F 10k RFB2 825k FBG 47H GND NTC PROG T RPROG 6.04k D5, D8, D9: DFLS240L D6: MMSZ5259BT1G OR DFLZ39 (OPT) LSW: SLF6028-470MR59 T: NTHS0402N02N1002F + Li-Ion 4120 F17 Figure 17. Resonant Coupled Power Transfer Charger Application RELATED PARTS PART NUMBER DESCRIPTION COMMENTS AN138 Wireless Power Users Guide LTC3335 Nanopower Buck-Boost with Intergrated Coulomb Counter LT3650-8.2/ LT3650-8.4 Monolithic 2A Switch Mode Standalone 9V VIN 32V (40V Absolute Maximum), 1MHz, 2A Programmable Charge Current, Timer Non-Synchronous 2-Cell Li-Ion or C/10 Termination, Small and Few External Components, 3mm x 3mm DFN-12 Package "-8.2" for 2x 4.1V Float Voltage Batteries, "-8.4" for 2x 4.2V Float Voltage Batteries Battery Charger LT3650-4.1/ LT3650-4.2 Monolithic 2A Switch Mode Standalone 4.75V VIN 32V (40V Absolute Maximum), 1MHz, 2A Programmable Charge Current, Non-Synchronous 1-Cell Li-Ion Timer or C/10 Termination, Small and Few External Components, 3mm x 3mm DFN-12 Package "-4.1" Battery Charger for 4.1V Float Voltage Batteries, "-4.2" for 4.2V Float Voltage Batteries LT3652HV Power Tracking 2A Battery Charger Input Supply Voltage Regulation Loop for Peak Power Tracking in (MPPT) Solar Applications Standalone, 4.95V VIN 34V (40V Absolute Maximum), 1MHz, 2A Charge Current, 3.3V VOUT 18V. Timer or C/10 Termination, 3mm x 3mm DFN-12 Package and MSOP-12 Packages LTC4070 Li-Ion/Polymer Shunt Battery Charger System Low Operating Current (450nA), 1% Float Voltage Accuracy Over Full Temperature and Shunt Current Range, 50mA Maximum Internal Shunt Current (500mA with External PFET), Pin Selectable Float Voltages: 4.0V, 4.1V, 4.2V. Ultralow Power Pulsed NTC Float Conditioning for Li-Ion/Polymer Protection, 8-Lead (2mm x 3mm) DFN and MSOP LTC4071 Li-Ion/Polymer Shunt Battery Charger System with Low Battery Disconnect Integrated Pack Protection, <10nA Low Battery Disconnect Protects Battery From Over-Discharge. Low Operating Current (550nA), 1% Float Voltage Accuracy Over Full Temperature and Shunt Current Range, 50mA Maximum Internal Shunt Current, Pin Selectable Float Voltages: 4.0V, 4.1V, 4.2V. Ultralow Power Pulsed NTC Float Conditioning for Li-Ion/Polymer Protection, 8-Lead (2mm x 3mm) DFN and MSOP LTC4065/ LTC4065A Standalone Li-Ion Battery Charger in 2mm x 2mm DFN 4.2V 0.6% Float Voltage, Up to 750mA Charge Current ; "A" Version Has /ACPR Function. 2mm x 2mm DFN Package LTC4123 25mA NiMH Wireless Charger-Receiver Low Minimum Input Voltage: 2.2V, Temperature Compensated Charge Voltage LTC4125 5W AutoResonant Wireless Power Transmitter Monolithic AutoResonant Full Bridge Driver. Transmit Power Automatically Adjusts to Receiver Load, Foreign Object Detection, Wide Operating Switching Frequency Range: 50kHz to 250kHz, Input Voltage Range 3V to 5.5V, 20-Lead 4mm x 5mm QFN Package 32 680nA Input Quiescent Current (Output in Regulation at No Load) 1.8V to 5.5V Input Operating Range, Up to 50mA of Output Current, Up to 90% Efficiency Rev. G 11/18 www.analog.com For more information www.analog.com ANALOG DEVICES, INC. 2013-2018