Preliminary Information H CAT5241 EE GEN FR ALO Quad Digitally Programmable Potentiometers (DPPTM) with 64 Taps and 2-wire Interface LE A D F R E ETM FEATURES Automatic recall of saved wiper settings at Four linear-taper digitally programmable power up potentiometers 64 resistor taps per potentiometer 2.5 to 6.0 volt operation End to end resistance 2.5k, 10k, 50k or 100k Standby current less than 1A Potentiometer control and memory access via 1,000,000 nonvolatile WRITE cycles 2 2-wire interface (I C like) 100 year nonvolatile memory data retention Low wiper resistance, typically 80 20-lead SOIC packages Nonvolatile memory storage for up to four wiper Commercial and industrial temperature ranges settings for each potentiometer DESCRIPTION registers is via a 2-wire serial bus (I2C-like). On powerup, the contents of the first data register (DR0) for each of the four potentiometers is automatically loaded into its respective wiper control register (WCR). The CAT5241 is four Digitally Programmable Potentiometers (DPPsTM) integrated with control logic and 16 bytes of NVRAM memory. Each DPP consists of a series of 63 resistive elements connected between two externally accessible end points. The tap points between each resistive element are connected to the wiper outputs with CMOS switches. A separate 6-bit control register (WCR) independently controls the wiper tap switches for each DPP. Associated with each wiper control register are four 6-bit non-volatile memory data registers (DR) used for storing up to four wiper settings. Writing to the wiper control register or any of the non-volatile data PIN CONFIGURATION The CAT5241 can be used as a potentiometer or as a two terminal, variable resistor. It is intended for circuit level or system level adjustments in a wide variety of applications. It is available in the 0C to 70C commercial and -40C to 85C industrial operating temperature ranges and offered in a 20-lead SOIC package. FUNCTIONAL DIAGRAM SOIC Package (J, W) RH0 RH1 RH2 R H3 VCC RW3 RW0 RL0 1 20 2 19 RH0 A0 3 18 4 17 A2 5 RW1 RL1 6 CAT 16 5241 15 7 14 SCL RH1 8 13 SDA 9 12 RW2 RL2 GND 10 11 RH2 RL3 RH3 SCL SDA A1 A3 2-WIRE BUS INTERFACE R W0 WIPER CONTROL REGISTERS R W1 WP R W2 A0 A1 A2 A3 CONTROL LOGIC NONVOLATILE DATA REGISTERS R W3 RL0 RL1 (c) 2003 by Catalyst Semiconductor, Inc. Characteristics subject to change without notice 1 RL2 R L3 Document No. 2011, Rev. F Prelimiary Information CAT5241 PIN DESCRIPTION PIN DESCRIPTIONS Pin (SOIC) Name 1 RW0 Wiper Terminal for Potentiometer 0 2 RL0 Low Reference Terminal for Potentiometer 0 3 RH0 High Reference Terminal for Potentiometer 0 4 A0 Device Address, LSB SCL: Serial Clock The CAT5241 serial clock input pin is used to clock all data transfers into or out of the device. Function 5 A2 6 RW1 Wiper Terminal for Potentiometer 1 Device Address 7 RL1 Low Reference Terminal for Potentiometer 1 8 RH1 High Reference Terminal for Potentiometer 1 9 SDA Serial Data Input/Output 10 GND Ground 11 RH2 High Reference Terminal for Potentiometer 2 12 RL2 Low Reference Terminal for Potentiometer 2 13 RW2 Wiper Terminal for Potentiometer 2 14 SCL Bus Serial Clock 15 A3 Device Address 16 A1 Device Address 17 RH3 High Reference Terminal for Potentiometer 3 18 RL3 Low Reference Terminal for Potentiometer 3 19 RW3 Wiper Terminal for Potentiometer 3 20 VCC Supply Voltage SDA: Serial Data The CAT5241 bidirectional serial data pin is used to transfer data into and out of the device. The SDA pin is an open drain output and can be wireOred with the other open drain or open collector outputs. A0, A1, A2, A3: Device Address Inputs These inputs set the device address when addressing multiple devices. When these pins are left floating the default values are zero. A total of sixteen devices can be addressed on a single bus. A match in the slave address must be made with the address input in order to initiate communication with the CAT5241. RH, RL: Resistor End Points The four sets of RH and RL pins are equivalent to the terminal connections on a mechanical potentiometer. RW: Wiper The four RW pins are equivalent to the wiper terminal of a mechanical potentiometer. DEVICE OPERATION The CAT5241 is four resistor arrays integrated with 2wire serial interface logic, four 6-bit wiper control registers and sixteen 6-bit, non-volatile memory data registers. Each resistor array contains 63 separate resistive elements connected in series. The physical ends of each array are equivalent to the fixed terminals of a mechanical potentiometer (RH and RL). RH and RL are symmetrical and may be interchanged. The tap positions between and at the ends of the series resistors are connected to the output wiper terminals (RW) by a Document No. 2011, Rev. F CMOS transistor switch. Only one tap point for each potentiometer is connected to its wiper terminal at a time and is determined by the value of the wiper control register. Data can be read or written to the wiper control registers or the non-volatile memory data registers via the 2-wire bus. Additional instructions allows data to be transferred between the wiper control registers and each respective potentiometer's non-volatile data registers. Also, the device can be instructed to operate in an "increment/decrement" mode. 2 Preliminary Information CAT5241 ABSOLUTE MAXIMUM RATINGS* Voltage on any Pin with Respect toVSS(1) .................... -2.0V to +VCC +2.0V *COMMENT Stresses above those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions outside of those listed in the operational sections of this specification is not implied. Exposure to any absolute maximum rating for extended periods may affect device performance and reliability. VCC with Respect to Ground ................ -2.0V to +7.0V Recommended Operating Conditions: Package Power Dissipation Capability (TA = 25C) ................................... 1.0W VCC = +2.5V to +6.0V Temperature Under Bias .................. -55C to +125C Storage Temperature ........................ -65C to +150C Temperature Commercial Industrial Lead Soldering Temperature (10 secs) ............ 300C Wiper Current .................................................. +12mA Note: Min 0C -40C Max 70C 85C (1) The minimum DC input voltage is -0.5V. During transitions, inputs may undershoot to -2.0V for periods of less than 20 ns. Maximum DC voltage on output pins is VCC +0.5V, which may overshoot to VCC +2.0V for periods of less than 20 ns. POTENTIOMETER CHARACTERISTICS Over recommended operating conditions unless otherwise stated. Symbol Parameter RPOT Potentiometer Resistance (-00) Test Conditions Min Typ 100 Max Units k RPOT Potentiometer Resistance (-50) 50 k RPOT Potentiometer Resistance (-10) 10 k RPOT Potentiometer Resistance (-2.5) 2.5 k Potentiometer Resistance Tolerance +20 % RPOT Matching 1 % 50 mW +6 mA 300 150 VCC V Power Rating 25C, each pot IW Wiper Current RW Wiper Resistance IW = +3mA @ VCC =3V RW Wiper Resistance IW = +3mA @ VCC = 5V VTERM Voltage on any RH or RL Pin VSS = 0V VN Noise GND Resolution (3) Rw(n)(actual)-R(n)(expected) Relative Linearity (4) Rw(n+1)-[Rw(n)+LSB](6) Absolute Linearity 80 TBD nV/ Hz 1.6 % (6) +1 LSB (5) +0.2 LSB (5) TCRPOT Temperature Coefficient of RPOT +300 ppm/C TCRATIO Ratiometric Temp. Coefficient CH/CL/CW Potentiometer Capacitances 10/10/25 pF RISO Isolation Resistance TBD fc Frequency Response 0.4 MHz 20 RPOT = 50k ppm/C Note: (1) This parameter is tested initially and after a design or process change that affects the parameter. (2) Latch-up protection is provided for stresses up to 100 mA on address and data pins from -1V to VCC +1V. (3) Absolute linearity is utilitzed to determine actual wiper voltage versus expected voltage as determined by wiper position when used as a potentiometer. (4) Relative linearity is utilized to determine the actual change in voltage between two successive tap positions when used as a potentiometer. It is a measure of the error in step size. (5) MI = RTOT / 63 or (RH - RL) / 63, single pot (6) n = 0, 1, 2, ..., 63 3 Document No. 2011, Rev. F Prelimiary Information CAT5241 D.C. OPERATING CHARACTERISTICS Over recommended operating conditions unless otherwise stated. Symbol Parameter Test Conditions Min Typ Max Units fSCL = 400kHz 1 mA VIN = GND or VCC; SDA Open 1 A VIN = GND to VCC 10 A VOUT = GND to VCC 10 A ICC Power Supply Current ISB Standby Current (VCC = 5.0V) ILI Input Leakage Current ILO Output Leakage Current VIL Input Low Voltage -1 VCC x 0.3 V VIH Input High Voltage VCC x 0.7 VCC + 1.0 V 0.4 V Max Units VOL1 Output Low Voltage (VCC = 3.0V) IOL = 3 mA CAPACITANCE TA = 25C, f = 1.0 MHz, VCC = 5V Symbol Test CI/O(1) CIN (1) Conditions Min Typ Input/Output Capacitance (SDA) VI/O = 0V 8 pF Input Capacitance (A0, A1, A2, A3, SCL) VIN = 0V 6 pF Max Units A.C. CHARACTERISTICS Over recommended operating conditions unless otherwise stated. Symbol Parameter Min Typ fSCL Clock Frequency 400 kHz TI(1) Noise Suppression Time Constant at SCL, SDA Inputs 50 ns tAA SLC Low to SDA Data Out and ACK Out 0.9 s tBUF(1) Time the Bus Must be Free Before a New Transmission Can Start 1.2 s tHD:STA Start Condition Hold Time 0.6 s tLOW Clock Low Period 1.2 s tHIGH Clock High Period 0.6 s tSU:STA Start Condition SetupTime (For a Repeated Start Condition) 0.6 s tHD:DAT Data in Hold Time 0 ns tSU:DAT Data in Setup Time 100 ns tR(1) SDA and SCL Rise Time 0.3 s tF(1) SDA and SCL Fall Time 300 ns tSU:STO Stop Condition Setup Time 0.6 s tDH Data Out Hold Time 50 ns POWER UP TIMING (1) Over recommended operating conditions unless otherwise stated. Symbol Parameter Min Typ Max Units tPUR Power-up to Read Operation 1 ms tPUW Power-up to Write Operation 1 ms Note: (1) This parameter is tested initially and after a design or process change that affects the parameter. Document No. 2011, Rev. F 4 Preliminary Information CAT5241 WRITE CYCLE LIMITS Over recommended operating conditions unless otherwise stated. Symbol tWR Parameter Min Typ Write Cycle Time Max Units 5 ms The write cycle is the time from a valid stop condition of a write sequence to the end of the internal program/erase cycle. During the write cycle, the bus interface circuits are disabled, SDA is allowed to remain high, and the device does not respond to its slave address. RELIABILITY CHARACTERISTICS Over recommended operating conditions unless otherwise stated. Symbol Parameter Reference Test Method Min NEND(1) Endurance MIL-STD-883, Test Method 1033 1,000,000 Cycles/Byte TDR(1) Data Retention MIL-STD-883, Test Method 1008 100 Years VZAP(1) ESD Susceptibility MIL-STD-883, Test Method 3015 2000 Volts ILTH(1)(2) Latch-Up JEDEC Standard 17 100 mA Figure 1. Bus Timing tHIGH tF tLOW Typ Max Units tR tLOW SCL tSU:STA tHD:DAT tHD:STA tSU:DAT tSU:STO SDA IN tAA tBUF tDH SDA OUT Figure 2. Write Cycle Timing SCL SDA 8TH BIT BYTE n ACK tWR STOP CONDITION START CONDITION ADDRESS Figure 3. Start/Stop Timing SDA SCL START BIT STOP BIT Note: (1) This parameter is tested initially and after a design or process change that affects the parameter. (2) tPUR and tPUW are the delays required from the time VCC is stable until the specified operation can be initiated. 5 Document No. 2011, Rev. F Prelimiary Information CAT5241 SERIAL BUS PROTOCOL the particular slave device it is requesting. The four most significant bits of the 8-bit slave address are fixed as 0101 for the CAT5241 (see Figure 5). The next four significant bits (A3, A2, A1, A0) are the device address bits and define which device the Master is accessing. Up to sixteen devices may be individually addressed by the system. Typically, +5V and ground are hard-wired to these pins to establish the device's address. The following defines the features of the 2-wire bus protocol: (1) Data transfer may be initiated only when the bus is not busy. (2) During a data transfer, the data line must remain stable whenever the clock line is high. Any changes in the data line while the clock is high will be interpreted as a START or STOP condition. After the Master sends a START condition and the slave address byte, the CAT5241 monitors the bus and responds with an acknowledge (on the SDA line) when its address matches the transmitted slave address. The device controlling the transfer is a master, typically a processor or controller, and the device being controlled is the slave. The master will always initiate data transfers and provide the clock for both transmit and receive operations. Therefore, the CAT5241 will be considered a slave device in all applications. Acknowledge START Condition After a successful data transfer, each receiving device is required to generate an acknowledge. The Acknowledging device pulls down the SDA line during the ninth clock cycle, signaling that it received the 8 bits of data. The START Condition precedes all commands to the device, and is defined as a HIGH to LOW transition of SDA when SCL is HIGH. The CAT5241 monitors the SDA and SCL lines and will not respond until this condition is met. The CAT5241 responds with an acknowledge after receiving a START condition and its slave address. If the device has been selected along with a write operation, it responds with an acknowledge after receiving each 8-bit byte. STOP Condition When the CAT5241 is in a READ mode it transmits 8 bits of data, releases the SDA line, and monitors the line for an acknowledge. Once it receives this acknowledge, the CAT5241 will continue to transmit data. If no acknowledge is sent by the Master, the device terminates data transmission and waits for a STOP condition. A LOW to HIGH transition of SDA when SCL is HIGH determines the STOP condition. All operations must end with a STOP condition. DEVICE ADDRESSING The bus Master begins a transmission by sending a START condition. The Master then sends the address of Figure 4. Acknowledge Timing SCL FROM MASTER 1 8 9 DATA OUTPUT FROM TRANSMITTER DATA OUTPUT FROM RECEIVER START ACKNOWLEDGE 5020 FHD F06 Document No. 2011, Rev. F 6 Preliminary Information CAT5241 Acknowledge Polling WRITE OPERATIONS The disabling of the inputs can be used to take advantage of the typical write cycle time. Once the stop condition is issued to indicate the end of the host's write operation, the CAT5241 initiates the internal write cycle. ACK polling can be initiated immediately. This involves issuing the start condition followed by the slave address. If the CAT5241 is still busy with the write operation, no ACK will be returned. If the CAT5241 has completed the write operation, an ACK will be returned and the host can then proceed with the next instruction operation. In the Write mode, the Master device sends the START condition and the slave address information to the Slave device. After the Slave generates an acknowledge, the Master sends the instruction byte that defines the requested operation of CAT5241. The instruction byte consist of a four-bit opcode followed by two register selection bits and two pot selection bits. After receiving another acknowledge from the Slave, the Master device transmits the data to be written into the selected register. The CAT5241 acknowledges once more and the Master generates the STOP condition, at which time if a nonvolatile data register is being selected, the device begins an internal programming cycle to non-volatile memory. While this internal cycle is in progress, the device will not respond to any request from the Master device. Figure 5. Slave Address Bits CAT5241 * ** 0 1 0 1 A3 A2 A1 A0 A0, A1, A2 and A3 correspond to pin A0, A1, A2 and A3 of the device. A0, A1, A2 and A3 must compare to its corresponding hard wired input pins. Figure 6. Write Timing BUS ACTIVITY: MASTER SDA LINE S T A R T INSTRUCTION BYTE SLAVE/DPP ADDRESS Fixed Variable Pot/WCR Data Register Address Address op code S T O P DR WCRDATA P S A C K A C K 7 A C K 5020 FHD F08 Document No. 2011, Rev. F Prelimiary Information CAT5241 INSTRUCTION AND REGISTER DESCRIPTION INSTRUCTION BYTE The next byte sent to the CAT5241 contains the instruction and register pointer information. The four most significant bits used provide the instruction opcode I [3:0]. The P1 and P0 bits point to one of four Wiper Control Registers. The least two significant bits, R1 and R0, point to one of the four data registers of each associated potentiometer. The format is shown in Table 2. Instructions SLAVE ADDRESS BYTE The first byte sent to the CAT5241 from the master/ processor is called the Slave/DPP Address Byte. The most significant four bits of the slave address are a device type identifier. These bits for the CAT5241 are fixed at 0101[B] (refer to Table 1). Data Register Selection Data Register Selected The next four bits, A3 - A0, are the internal slave address and must match the physical device address which is defined by the state of the A3 - A0 input pins for the CAT5241 to successfully continue the command sequence. Only the device which slave address matches the incoming device address sent by the master executes the instruction. The A3 - A0 inputs can be actively driven by CMOS input signals or tied to VCC or VSS. R1 R0 DR0 0 0 DR1 0 1 DR2 1 0 DR3 1 1 Table 1. Identification Byte Format Device Type Identifier Slave Address ID3 ID2 ID1 ID0 0 1 0 1 A3 A2 A1 (MSB) A0 (LSB) Table 2. Instruction Byte Format Instruction Opcode I3 (MSB) Document No. 2011, Rev. F I2 WCR/Pot Selection I1 P1 I0 8 P0 Data Register Selection R1 R0 (LSB) Preliminary Information CAT5241 four Data Registers and the associated Wiper Control Register. Any data changes in one of the Data Registers is a non-volatile operation and will take a maximum of 5ms. WIPER CONTROL AND DATA REGISTERS Wiper Control Register (WCR) The CAT5241 contains four 6-bit Wiper Control Registers, one for each potentiometer. The Wiper Control Register output is decoded to select one of 64 switches along its resistor array. The contents of the WCR can be altered in four ways: it may be written by the host via Write Wiper Control Register instruction; it may be written by transferring the contents of one of four associated Data Registers via the XFR Data Register instruction, it can be modified one step at a time by the Increment/decrement instruction (see Instruction section for more details). Finally, it is loaded with the content of its data register zero (DR0) upon power-up. If the application does not require storage of multiple settings for the potentiometer, the Data Registers can be used as standard memory locations for system parameters or user preference data. INSTRUCTIONS Four of the nine instructions are three bytes in length. These instructions are: -- Read Wiper Control Register - read the current wiper position of the selected potentiometer in the WCR -- Write Wiper Control Register - change current wiper position in the WCR of the selected potentiometer The Wiper Control Register is a volatile register that loses its contents when the CAT5241 is powered-down. Although the register is automatically loaded with the value in DR0 upon power-up, this may be different from the value present at power-down. -- Read Data Register - read the contents of the selected Data Register Data Registers (DR) -- Write Data Register - write a new value to the selected Data Register Each potentiometer has four 6-bit non-volatile Data Registers. These can be read or written directly by the host. Data can also be transferred between any of the The basic sequence of the three byte instructions is illustrated in Figure 8. These three-byte instructions Table 3. Instruction Set Instruction Set WCR1/ WCR0/ P0 P1 Instruction I3 I2 I1 I0 R1 R0 Read Wiper Control Register Write Wiper Control Register 1 0 0 1 1/0 1/0 0 0 1 0 1 0 1/0 1/0 0 0 Read Data Register 1 0 1 1 1/0 1/0 1/0 1/0 Write Data Register 1 1 0 0 1/0 1/0 1/0 1/0 XFR Data Register to Wiper Control Register 1 1 0 1 1/0 1/0 1/0 1/0 XFR Wiper Control Register to Data Register 1 1 1 0 1/0 1/0 1/0 1/0 Global XFR Data Registers to Wiper Control Registers 0 0 0 1 0 0 1/0 1/0 Global XFR Wiper Control Registers to Data Register 1 0 0 0 0 0 1/0 1/0 Increment/Decrement Wiper Control Register 0 0 1 0 1/0 1/0 0 0 Operation Read the contents of the Wiper Control Register pointed to by P1-P0 Write new value to the Wiper Control Register pointed to by P1-P0 Read the contents of the Data Register pointed to by P1-P0 and R1-R0 Write new value to the Data Register pointed to by P1-P0 and R1-R0 Transfer the contents of the Data Register pointed to by P1-P0 and R1-R0 to its associated Wiper Control Register Transfer the contents of the Wiper Control Register pointed to by P1-P0 to the Data Register pointed to by R1-R0 Transfer the contents of the Data Registers pointed to by R1-R0 of all four pots to their respective Wiper Control Register s Transfer the contents of both Wiper Control Registers to their respective data Registers pointed to by R1-R0 of all four pots Enable Increment/decrement of the Control Latch pointed to by P1-P0 Note: 1/0 = data is one or zero 9 Document No. 2011, Rev. F Prelimiary Information CAT5241 -- Global XFR Data Register to Wiper Control Register This transfers the contents of all specified Data Registers to the associated Wiper Control Registers. exchange data between the WCR and one of the Data Registers. The WCR controls the position of the wiper. The response of the wiper to this action will be delayed by tWRL. A transfer from the WCR (current wiper position), to a Data Register is a write to non-volatile memory and takes a minimum of tWR to complete. The transfer can occur between one of the four potentiometers and one of its associated registers; or the transfer can occur between all potentiometers and one associated register. -- Global XFR Wiper Counter Register to Data Register This transfers the contents of all Wiper Control Registers to the specified associated Data Registers. Four instructions require a two-byte sequence to complete, as illustrated in Figure 7. These instructions transfer data between the host/processor and the CAT5241; either between the host and one of the data registers or directly between the host and the Wiper Control Register. These instructions are: INCREMENT/DECREMENT COMMAND The final command is Increment/Decrement (Figure 5 and 9). The Increment/Decrement command is different from the other commands. Once the command is issued and the CAT5241 has responded with an acknowledge, the master can clock the selected wiper up and/or down in one segment steps; thereby providing a fine tuning capability to the host. For each SCL clock pulse (tHIGH) while SDA is HIGH, the selected wiper will move one resistor segment towards the RH terminal. Similarly, for each SCL clock pulse while SDA is LOW, the selected wiper will move one resistor segment towards the RL terminal. -- XFR Data Register to Wiper Control Register This transfers the contents of one specified Data Register to the associated Wiper Control Register. -- XFR Wiper Control Register to Data Register This transfers the contents of the specified Wiper Control Register to the specified associated Data Register. See Instructions format for more detail. Figure 7. Two-Byte Instruction Sequence SDA 0 1 0 1 S ID3 ID2 ID1 ID0 A3 A2 A1 A0 T A Internal R Device ID Address T A I3 C K I2 I1 I0 Instruction Opcode P1 P0 R1 R0 Pot/WCR Register Address Address A C K S T O P Figure 8. Three-Byte Instruction Sequence SDA 0 1 0 1 S ID3 ID2 ID1 ID0 A3 T A Device ID R T A2 A0 A I3 C K Internal Address I2 A1 I1 I0 Instruction Opcode R1 R0 A C K Data Pot/WCR Address Register Address P1 P0 D7 D6 D5 D4 D3 D2 D1 D0 A C K WCR[7:0] or Data Register D[7:0] S T O P Figure 9. Increment/Decrement Instruction Sequence 0 SDA S T A R T 1 0 1 ID3 ID2 ID1 ID0 Device ID Document No. 2011, Rev. F A3 A2 A1 A0 Internal Address A C K I3 I2 I1 I0 Instruction Opcode 10 P1 P0 R1 R0 Pot/WCR Data Address Register Address A C K I N C 1 I N C 2 I N C n D E C 1 D E C n S T O P Preliminary Information CAT5241 Figure 10. Increment/Decrement Timing Limits INC/DEC Command Issued tWRID SCL SDA Voltage Out RW INSTRUCTION FORMAT Read Wiper Control Register (WCR) S T A R T DEVICE ADDRESSES 0 1 0 1 A3 A2 A1 A0 A C K INSTRUCTION 1 0 0 1 P1 P0 0 0 A C K 4 3 2 1 0 A C K S T O P DATA A C 2 1 0 K S T O P A C 2 1 0 K S T O P A C 2 1 0 K S T O P DATA 7 6 5 Write Wiper Control Register (WCR) S T A R T DEVICE ADDRESSES 0 1 0 1 A3 A2 A1 A0 A C K INSTRUCTION 1 0 1 0 P1 P0 0 0 A C K 7 6 5 4 3 Read Data Register (DR) S T A R T DEVICE ADDRESSES 0 1 0 1 A3 A2 A1 A0 A C K A C 1 0 1 1 P1 P0 R1 R0 7 6 K A C K A C 1 1 0 0 P1 P0 R1 R0 7 6 K INSTRUCTION DATA 5 4 3 Write Data Register (DR) S T A R T DEVICE ADDRESSES 0 1 0 1 A3 A2 A1 A0 INSTRUCTION 11 DATA 5 4 3 Document No. 2011, Rev. F Prelimiary Information CAT5241 INSTRUCTION FORMAT (continued) Global Transfer Data Register (DR) to Wiper Control Register (WCR) S T A R T A C 0 1 0 1 A3 A2 A1 A0 K DEVICE ADDRESS A C 0 0 0 1 0 0 R1 R0 K INSTRUCTION S T O P Global Transfer Wiper Control Register (WCR) to Data Register (DR) S T A R T A C 0 1 0 1 A3 A2 A1 A0 K DEVICE ADDRESS INSTRUCTION 1 0 0 0 0 0 R1 R0 A C K S T O P Transfer Wiper Control Register (WCR) to Data Register (DR) S T A R T A C 0 1 0 1 A3 A2 A1 A0 K DEVICE ADDRESS A C 1 1 1 0 P1 P0 R1R0 K INSTRUCTION S T O P Transfer Data Register (DR) to Wiper Control Register (WCR) S T A R T A C 0 1 0 1 A3 A2 A1 A0 K DEVICE ADDRESS A C 1 1 1 0 P1 P0 R1R0 K INSTRUCTION S T O P Increment (I)/Decrement (D) Wiper Control Register (WCR) S T A R T A INSTRUCTION C 0 1 0 1 A3 A2 A1 A0 0 0 1 0 P1 P0 0 0 K DEVICE ADDRESS A C K DATA I/D I/D * * * A C I/D I/D K Notes: (1) Any write or transfer to the Non-volatile Data Registers is followed by a high voltage cycle after a STOP has been issued. Document No. 2011, Rev. F 12 S T O P Preliminary Information CAT5241 ORDERING INFORMATION -10 5241 W: SOIC (Lead free, Halogen free) -25: 2.5kohm -10: 10kohm -50: 50kohm -00: 100kohm Notes: (1) The device used in the above example is a CAT5241JI-10-TE13 (SOIC, Industrial Temperature, 10kohm, Tape & Reel) PACKAGING INFORMATION 20-LEAD 300 MIL WIDE SOIC (J) 0.2914 (7.40) 0.2992 (7.60) 0.394 (10.00) 0.419 (10.65) 0.5985 (15.20) 0.6141 (15.60) 0.0926 (2.35) 0.1043 (2.65) 0.050 (1.27) BSC 0.013 (0.33) 0.020 (0.51) 0.0040 (0.10) 0.0118 (0.30) 0.010 (0.25) X 45 0.029 (0.75) 0.0091 (0.23) 0.0125 (0.32) 0 --8 0.016 (0.40) 0.050 (1.27) 13 Document No. 2011, Rev. F Copyrights, Trademarks and Patents Trademarks and registered trademarks of Catalyst Semiconductor include each of the following: DPP TM DPPs TM AE2 TM I2C is a trademark of Philips Corporation Catalyst Semiconductor has been issued U.S. and foreign patents and has patent applications pending that protect its products. For a complete list of patents issued to Catalyst Semiconductor contact the Company's corporate office at 408.542.1000. CATALYST SEMICONDUCTOR MAKES NO WARRANTY, REPRESENTATION OR GUARANTEE, EXPRESS OR IMPLIED, REGARDING THE SUITABILITY OF ITS PRODUCTS FOR ANY PARTICULAR PURPOSE, NOR THAT THE USE OF ITS PRODUCTS WILL NOT INFRINGE ITS INTELLECTUAL PROPERTY RIGHTS OR THE RIGHTS OF THIRD PARTIES WITH RESPECT TO ANY PARTICULAR USE OR APPLICATION AND SPECIFICALLY DISCLAIMS ANY AND ALL LIABILITY ARISING OUT OF ANY SUCH USE OR APPLICATION, INCLUDING BUT NOT LIMITED TO, CONSEQUENTIAL OR INCIDENTAL DAMAGES. Catalyst Semiconductor products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Catalyst Semiconductor product could create a situation where personal injury or death may occur. Catalyst Semiconductor reserves the right to make changes to or discontinue any product or service described herein without notice. Products with data sheets labeled "Advance Information" or "Preliminary" and other products described herein may not be in production or offered for sale. Catalyst Semiconductor advises customers to obtain the current version of the relevant product information before placing orders. Circuit diagrams illustrate typical semiconductor applications and may not be complete. Catalyst Semiconductor, Inc. Corporate Headquarters 1250 Borregas Avenue Sunnyvale, CA 94089 Phone: 408.542.1000 Fax: 408.542.1200 www.catalyst-semiconductor.com Publication #: Revison: Issue date: Type: 2011 F 6/27/03 Preliminary