PCA9518 Expandable 5-channel I2C-bus hub Rev. 05 -- 2 December 2008 Product data sheet 1. General description The PCA9518 is a BiCMOS integrated circuit intended for application in I2C-bus and SMBus systems. While retaining all the operating modes and features of the I2C-bus system, it permits extension of the I2C-bus by buffering both the data (SDA) and the clock (SCL) lines, thus enabling virtually an unlimited number of buses of 400 pF. The I2C-bus capacitance limit of 400 pF restricts the number of devices and bus length. Using the PCA9518 enables the system designer to divide the bus into an unlimited number of segments off of a hub where any segment to segment transition sees only one repeater delay and is multiple master capable on each segment. Using multiple PCA9518 parts, any width hub (in multiples of five)1 can be implemented using the expansion pins. The PCA9518 is a wider voltage range (2.3 V to 3.6 V) version of the PCA9518 and also improves partial power-down performance, keeping I2C-bus I/O pins in high-impedance state when VDD is below 2.0 V. A PCA9518 cluster cannot be put in series with a PCA9515/16 or with another PCA9518 cluster. Multiple PCA9518 devices can be grouped with other PCA9518 devices into any size cluster thanks to the EXPxxxn pins that allow the I2C-bus signals to be sent/received from/to one PCA9518 to/from another PCA9518 within the cluster. Since there is no direction pin, slightly different `legal' low voltage levels are used to avoid lock-up conditions between the input and the output of individual repeaters in the cluster. A `regular LOW' applied at the input of any of the PCA9518 devices will then be propagated as a `buffered LOW' with a slightly higher value to all enabled outputs in the PCA9518 cluster. When this `buffered LOW' is applied to a PCA9515 and PCA9516 or separate PCA9518 cluster (not connected via the EXPxxxn pins) in series, the second PCA9515 and PCA9516 or PCA9518 cluster will not recognize it as a `regular LOW' and will not propagate it as a `buffered LOW' again. The PCA9510/9511/9513/9514 and PCA9512 cannot be used in series with the PCA9515 and PCA9516 or PCA9518, but can be used in series with themselves since they use shifting instead of static offsets to avoid lock-up conditions. 1. Only four ports per device are available if individual Enable is required. PCA9518 NXP Semiconductors Expandable 5-channel I2C-bus hub 2. Features n n n n n n n n n n n n Expandable 5 channel, bidirectional buffer I2C-bus and SMBus compatible Active HIGH individual repeater enable inputs Open-drain input/outputs Lock-up free operation Supports arbitration and clock stretching across the repeater Accommodates Standard-mode and Fast-mode I2C-bus devices and multiple masters Powered-off high-impedance I2C-bus pins Operating supply voltage range of 3.0 V to 3.6 V 5 V tolerant I2C-bus and enable pins 0 Hz to 400 kHz clock frequency2 ESD protection exceeds 2000 V HBM per JESD22-A114, 200 V MM per JESD22-A115, and 1000 V CDM per JESD22-C101 n Latch-up testing is done to JEDEC Standard JESD78 which exceeds 100 mA n Package offerings: SO20 and TSSOP20 3. Ordering information Table 1. Ordering information Tamb = -40 C to +85 C Type number Topside mark Package Name Description Version PCA9518D PCA9518D SO20 plastic small outline package; 20 leads; body width 7.5 mm SOT163-1 PCA9518PW PCA9518 TSSOP20 plastic thin shrink small outline package; 20 leads; body width 4.4 mm SOT360-1 2. The maximum system operating frequency may be less than 400 kHz because of the delays added by the repeater. PCA9518_5 Product data sheet (c) NXP B.V. 2008. All rights reserved. Rev. 05 -- 2 December 2008 2 of 21 PCA9518 NXP Semiconductors Expandable 5-channel I2C-bus hub 4. Block diagram VCC EXPSCL1 EXPSCL2 PCA9518 BUFFER SCL0 BUFFER SCL1 BUFFER SCL4 BUFFER SCL3 BUFFER SDA4 BUFFER SDA3 HUB LOGIC BUFFER SCL2 EXPSDA1 EXPSDA2 BUFFER SDA0 BUFFER SDA1 HUB LOGIC BUFFER SDA2 EN1 EN4 EN2 EN3 002aae325 GND Fig 1. Block diagram of PCA9518 A more detailed view of Figure 1 buffer is shown in Figure 2. data to output in inc enable Fig 2. 002aac531 Buffer detail The output pull-down voltage of each internal buffer is set for approximately 0.5 V, while the input threshold of each internal buffer is set about 0.07 V lower, when the output is internally driven LOW. This prevents a lock-up condition from occurring. PCA9518_5 Product data sheet (c) NXP B.V. 2008. All rights reserved. Rev. 05 -- 2 December 2008 3 of 21 PCA9518 NXP Semiconductors Expandable 5-channel I2C-bus hub 5. Pinning information 5.1 Pinning EXPSCL1 1 20 VCC 2 20 VCC 19 EXPSDA2 EXPSCL1 1 EXPSCL2 EXPSCL2 2 19 EXPSDA2 SCL0 3 18 EXPSDA1 SCL0 3 18 EXPSDA1 SDA0 4 17 EN4 SDA0 4 17 EN4 SCL1 5 16 SDA4 SCL1 5 SDA1 6 15 SCL4 SDA1 6 EN1 7 14 EN3 SCL2 8 13 SDA3 SCL2 8 13 SDA3 SDA2 9 12 SCL3 SDA2 9 12 SCL3 PCA9518D GND 10 11 EN2 EN1 7 Pin configuration for SO20 16 SDA4 15 SCL4 14 EN3 GND 10 002aac739 Fig 3. PCA9518PW 11 EN2 002aac740 Fig 4. Pin configuration for TSSOP20 5.2 Pin description Table 2. Pin description Symbol Pin Description EXPSCL1 1 expandable serial clock pin 1 EXPSCL2 2 expandable serial clock pin 2 SCL0 3 serial clock bus 0 SDA0 4 serial data bus 0 SCL1 5 serial clock bus 1 SDA1 6 serial data bus 1 EN1 7 active HIGH bus 1 enable input SCL2 8 serial clock bus 2 SDA2 9 serial data bus 2 GND 10 supply ground EN2 11 active HIGH bus 2 enable input SCL3 12 serial clock bus 3 SDA3 13 serial data bus 3 EN3 14 active HIGH bus 3 enable input SCL4 15 serial clock bus 4 SDA4 16 serial data bus 4 EN4 17 active HIGH bus 4 enable input EXPSDA1 18 expandable serial data pin 1 EXPSDA2 19 expandable serial data pin 2 VCC 20 supply voltage PCA9518_5 Product data sheet (c) NXP B.V. 2008. All rights reserved. Rev. 05 -- 2 December 2008 4 of 21 PCA9518 NXP Semiconductors Expandable 5-channel I2C-bus hub 6. Functional description The PCA9518 BiCMOS integrated circuit is a five-way hub repeater, which enables I2C-bus and similar bus systems to be expanded in increments of five with only one repeater delay and no functional degradation of system performance. The PCA9518 BiCMOS integrated circuit contains five multi-directional, open-drain buffers specifically designed to support the standard low-level contention arbitration of the I2C-bus. Except during arbitration or clock stretching, the PCA9518 acts like a pair of non-inverting, open-drain buffers, one for SDA and one for SCL. Refer to Figure 1 "Block diagram of PCA9518". 6.1 Enable The enable pins EN1 through EN4 are active HIGH and have internal pull-up resistors. Each enable pin ENn controls its associated SDAn and SCLn ports. When LOW, the ENn pin blocks the inputs from SDAn and SCLn, as well as disabling the output drivers on the SDAn and SCLn pins. The enable pins should only change state when both the global bus and the local port are in an idle state to prevent system failures. The active HIGH enable pins allow the use of open-drain drivers which can be wire-ORed to create a distributed enable where either centralized control signal (master) or spoke signal (sub-master) can enable the channel when it is idle. Unused channels must have pull-up resistors unless their enable pin (ENn) is always LOW. Port 0 must always have pull-up resistors since it is always present in the bus and cannot be disabled. 6.2 Expansion The PCA9518 includes 4 open-drain I/O pins used for expansion. Two expansion pins, EXPSDA1 and EXPSDA2 are used to communicate the internal state of the serial data within each hub to the other hubs. The EXPSDA1 pins of all hubs are connected together to form an open-drain bus. Similarly, all EXPSDA2 pins, EXPSCL1 pins, and all EXPSCL2 pins are connected together forming a 4-wire bus between hubs. When it is necessary to be able to deselect every port, each expansion device only contributes 4 ports which can be enabled or disables because the fifth does not have an enable pin. Pull-up resistors are required on the EXPxxxn3 pins even if only one PCA9518 is used. 6.3 I2C-bus systems As with the standard I2C-bus system, pull-up resistors are required to provide the logic HIGH levels on the buffered bus. (Standard open-collector or open-drain configuration of the I2C-bus). The size of these pull-up resistors depends on the system, but each side of the repeater must have a pull-up resistor. This part is designed to work with Standard-mode (0 Hz to 100 kHz) and Fast-mode (0 Hz to 400 kHz) I2C-bus devices in addition to SMBus devices. Standard-mode I2C-bus devices only specify 3 mA output drive; this limits the termination current to 3 mA in a generic I2C-bus system where 3. `xxxn' is SDA1, SDA2, SCL1 or SCL2. `xxx' is SDA or SCL. PCA9518_5 Product data sheet (c) NXP B.V. 2008. All rights reserved. Rev. 05 -- 2 December 2008 5 of 21 PCA9518 NXP Semiconductors Expandable 5-channel I2C-bus hub Standard-mode devices and multiple masters are possible. Please see application note AN255, I2C/SMBus Repeaters, Hubs and Expanders for additional information on sizing resistors. 7. Application design-in information A typical application is shown in Figure 5. In this example, the system master is running on a 3.3 V I2C-bus while the slaves are connected to a 3.3 V or 5 V bus. All buses run at 100 kHz unless slave 3, slave 4 and slave 5 are isolated from the bus. Then the master bus and slave 1, slave 2 and slave 6 can run at 400 kHz. Any segment of the hub can talk to any other segment of the hub. Bus masters and slaves can be located on any segment with 400 pF load allowed on each segment. The PCA9518 is 5 V tolerant, so it does not require any additional circuitry to translate between the different bus voltages. When one port of the PCA9518 is pulled LOW by a device on the I2C-bus, a CMOS hysteresis type input detects the falling edge and drives the EXPxxx1 line LOW, when the EXPxxx1 voltage is less than 0.5VCC, the other ports are pulled down to the VOL of the PCA9518 which is typically 0.5 V. In order to illustrate what would be seen in a typical application, refer to Figure 6. If the bus master in Figure 5 were to write to the slave through the PCA9518, we would see the waveform shown in Figure 6. This looks like a normal I2C-bus transmission except for the small foot preceding each clock LOW-to-HIGH transition and proceeding each data LOW-to-HIGH transition for the master. The foot height is the difference between the LOW level driven by the master and the higher voltage LOW level driven by the PCA9518 repeater. Its width corresponds to an effective clock stretching coming from the PCA9518 that delays the rising edge of the clock. That same magnitude of delay is seen on the rising edge of the data. The foot on the rising edge of the data is extended through the 9th clock pulse as the PCA9518 repeats the acknowledge from the slave to the master. The clock of the slave looks normal except the VOL is the ~0.5 V level generated by the PCA9518. The SDA at the slave has a particularly interesting shape during the 9th clock cycle where the slave pulls the line below the value driven by the PCA9518 during the acknowledge and then returns to the PCA9518 level creating a foot before it completes the LOW-to-HIGH transition. SDA lines other than the one with the master and the one with the slave have a uniform LOW level driven by the PCA9518 repeater. The other four waveforms are the expansion bus signals and are included primarily for timing reference points. All timing on the expansion bus is with respect to 0.5VCC. EXPSDA1 is the expansion bus that is driven LOW whenever any SDA pin falls below 0.3VCC. EXPSDA2 is the expansion bus that is driven LOW whenever any pin is 0.4 V. EXPSCL1 is the expansion bus that is driven LOW whenever any SCL pin falls below 0.3VCC. EXPSCL2 is the expansion bus that is driven LOW whenever any SCL pin is 0.4 V. The EXPSDA2 returns HIGH after the SDA pin that was the last one being held below 0.4 V by an external driver starts to rise. The last SDA to rise above 0.4 V is held down by the PCA9518 to ~0.5 V until after the delay of the circuit which determines that it was the last to rise, then it is allowed to rise above the ~0.5 V level driven by the PCA9518. Considering the bus 0 SDA to be the last one to go above 0.4 V, then the EXPSDA1 returns to HIGH after the EXPSDA2 is HIGH and either the bus 0 SDA rise time PCA9518_5 Product data sheet (c) NXP B.V. 2008. All rights reserved. Rev. 05 -- 2 December 2008 6 of 21 PCA9518 NXP Semiconductors Expandable 5-channel I2C-bus hub is 1 s or, when the bus 0 SDA reaches 0.7VCC, whichever occurs first. After both EXPSDA2 and EXPSDA1 are HIGH the rest of the SDA lines are allowed to rise. The same description applies for the EXPSCL1, EXPSCL2, and SCL pins. 3.3 V 5V 5V VCC SDA SDA1 SCL SUBSYSTEM 5 100 kHz SCL1 VCC EXPSDA1 EXPSDA1 EXPSDA2 EXPSDA2 EXPSCL1 EXPSCL1 EXPSCL2 EXPSCL2 SDA1 SDA SCL1 SCL SUBSYSTEM 1 400 kHz 3.3 V 3.3 V SDA SDA2 SDA2 SDA SCL SUBSYSTEM 6 400 kHz SCL2 SCL2 SCL SUBSYSTEM 2 400 kHz 3.3 V or 5 V SDA0 SDA SDA0 SCL0 SCL SCL0 5V PCA9518 PCA9518 DEVICE 2 DEVICE 1 BUS MASTER SDA3 SCL3 disabled; not connected 400 kHz 3.3 V or 5 V EN1 EN1 EN2 EN2 EN3 EN3 EN4 EN4 SDA3 SDA SCL3 SCL SUBSYSTEM 3 100 kHz 3.3 V SDA4 SDA4 SDA SCL4 SCL4 SCL SUBSYSTEM 4 100 kHz GND GND 002aae326 Only two of the five channels on the PCA9518 Device 2 are being used. EN3 and EN4 are connected to GND to disable channels 3 and 4 and/or SDA3/SCL3 and SDA4/SCL4 are pulled up to VCC. SDA0 and SCL0 can be used as a normal I2C-bus port, but if unused then it must be pulled up to VCC since there is no enable pin. The pull-ups shown on Device 2 channels 3 and 4 are not required if their enable pins (ENn) are permanently held LOW. Fig 5. Typical application: multiple expandable 5-channel I2C-bus hubs PCA9518_5 Product data sheet (c) NXP B.V. 2008. All rights reserved. Rev. 05 -- 2 December 2008 7 of 21 PCA9518 NXP Semiconductors Expandable 5-channel I2C-bus hub 9th clock cycle VOL of master VOL of PCA9518 9th clock cycle SCL of master Bus 0 tstretch SDA of master tPHL1 EXPSDA1 tPLH1 tPHL2 tPLH2, tPLH1 tPLH2 EXPSDA2 expansion bus EXPSCL1 EXPSCL2 SCL of slave Bus 1 VOL of slave VOL of PCA9518 SDA of slave tPHL tPLH Bus n with n > 1 002aae327 Fig 6. Bus waveforms It is important to note that any arbitration or clock stretching events on Bus 1 require that the VOL of the devices on Bus 1 be 70 mV below the VOL of the PCA9518 (see VOL-VILc in Section 9 "Static characteristics") to be recognized by the PCA9518 and then transmitted to Bus 0. PCA9518_5 Product data sheet (c) NXP B.V. 2008. All rights reserved. Rev. 05 -- 2 December 2008 8 of 21 PCA9518 NXP Semiconductors Expandable 5-channel I2C-bus hub 8. Limiting values Table 3. Limiting values In accordance with the Absolute Maximum Rating System (IEC 60134). Symbol Parameter Conditions Min Max Unit VCC to GND [1] -0.5 +7 V SCL or SDA [1] -0.5 +7 V - 50 mA VCC supply voltage VI2C-bus I2C-bus II input current Ptot total power dissipation - 300 mW Tstg storage temperature -55 +125 C Tamb ambient temperature -40 +85 C [1] voltage any pin operating Voltages with respect to pin GND. PCA9518_5 Product data sheet (c) NXP B.V. 2008. All rights reserved. Rev. 05 -- 2 December 2008 9 of 21 PCA9518 NXP Semiconductors Expandable 5-channel I2C-bus hub 9. Static characteristics Table 4. Static characteristics VCC = 3.0 V to 3.6 V; GND = 0 V; Tamb = -40 C to +85 C; unless otherwise specified. Symbol Parameter Conditions Min Typ Max Unit 3.0 3.3 3.6 V - 7.5 10 mA - 9 11 mA - 9 11 mA Supplies VCC supply voltage ICCH HIGH-level supply current both channels HIGH VCC = 3.6 V; SDAn = SCLn = VCC ICCL LOW-level supply current both channels LOW VCC = 3.6 V; one SDA and one SCL = GND; other SDA and SCL open ICCLc contention LOW-level supply current VDD = 3.6 V; SDAn = SCLn = VSS Input SCL; input/output SDA HIGH-level input voltage 0.7VCC - 5.5 V SCL, SDA [1] -0.5 - +0.3VCC V VILc contention LOW-level input voltage SCL, SDA [2] -0.5 - +0.4 V VIK input clamping voltage II = -18 mA - - -1.2 V ILI input leakage current VI = 3.6 V - - 1 A IIL LOW-level input current SCL, SDA; VI = 0.2 V - - 20 A 0.47 0.52 0.6 V VIH LOW-level input voltage VIL SCL, SDA SCL, SDA; IOL = 0 mA[3] VOL LOW-level output voltage or 6 mA VOL-VILc difference between LOW-level guaranteed by design output and LOW-level input voltage contention - - 70 mV Ci input capacitance - 6 8 pF VI = 3 V or 0 V Enable 1 to Enable 4 (EN1 to EN4) VIL LOW-level input voltage -0.5 - +0.8 V VIH HIGH-level input voltage 2.0 - 5.5 V IIL LOW-level input current - 10 30 A ILI input leakage current -1 - +1 A Ci input capacitance - 3 7 pF V VI = 0.2 V; EN1 to EN4 VI = 3.0 V or 0 V Expansion pins (EXPSCL1, EXPSCL2, EXPSDA1, EXPSDA2) VIH HIGH-level input voltage EXPxxxn 0.55VCC - 5.5 VIL LOW-level input voltage EXPxxxn -0.5 - +0.45VCC V IIL LOW-level input current EXPxxxn; VI = 0.2 V - - 5 A VOL LOW-level output voltage EXPxxxn; IOL = 12 mA - - 0.5 V Ci input capacitance VI = 3.0 V or 0 V - 6 8 pF [1] VIL specification is for the first LOW level seen by the SDAn/SCLn lines. [2] VILc is for the second and subsequent LOW levels seen by the SDAn/SCLn lines. [3] Test performed with IOL = 10 A. PCA9518_5 Product data sheet (c) NXP B.V. 2008. All rights reserved. Rev. 05 -- 2 December 2008 10 of 21 PCA9518 NXP Semiconductors Expandable 5-channel I2C-bus hub 10. Dynamic characteristics Table 5. Dynamic characteristics Symbol Parameter Conditions Min Typ Max Unit 105 202 389 ns 110 259 265 ns tPHL HIGH to LOW propagation delay SDA to SDAn, or SCL to SCLn; Figure 7 [1][2] tPLH LOW to HIGH propagation delay SDA to SDAn, or SCL to SCLn; Figure 7 [1][3] tPHL1 HIGH to LOW propagation delay 1 EXPSDA1 to SDA, or EXPSCL1 to SCL; Figure 7 109 193 327 ns tPLH1 LOW to HIGH propagation delay 1 EXPSDA1 to SDA, or EXPSCL1 to SCL; Figure 7 130 153 179 ns tPLH2 LOW to HIGH propagation delay 2 EXPSDA2 to SDA, or EXPSCL2 to SCL; Figure 7 160 234 279 ns tTHL HIGH to LOW output transition time SDA, SCL; Figure 7 58 110 187 ns tTLH LOW to HIGH output transition time SDA, SCL; Figure 7 - 0.85 RC - ns tsu set-up time enable to START condition 300 - - ns th hold time enable after STOP condition 300 - - ns [1] The SDA and SCL propagation delays are dominated by rise times or fall times. The fall times are mostly internally controlled and are only sensitive to load capacitance. The rise times are RC time constant controlled and therefore a specific numerical value can only be given for fixed RC time constants. [2] The SDA HIGH to LOW propagation delay includes the fall time from VCC to 0.5VCC of the EXPSDA1 or EXPSCL1 pins and the SDA or SCL fall time from the quiescent HIGH (usually VCC) to below 0.3VCC. The SDA and SCL outputs have edge rate control circuits included which make the fall time almost independent of load capacitance. [3] The SDA or SCL LOW to HIGH propagation delay includes the rise time constant from the quiescent LOW to 0.5VCC for the EXPSDA1 or EXPSCL2, the rise time constant for the quiescent LOW to 0.5VCC for the EXPSDA1 or EXPSCL1, and the rise time constant from the quiescent external driven LOW to 0.7VCC for the SDA or SCL output. All of these rise times are RC time constants determined by the external resistance and total capacitance for the various nodes. tTHL input SDA or SCL tTLH 0.7VCC 0.7VCC 0.3VCC 0.4 V tPHL 0.3VCC 0.4 V effective stretch tPHL1 EXPSDA1 or EXPSCL1 0.5VCC 0.5VCC tPHL2 tPLH2 EXPSDA2 or EXPSCL2 0.5VCC 0.5VCC tPLH tPLH1 tPHL1 tPLH2 tTHL tTLH 0.7VCC output SDA or SCL 0.52 V Fig 7. 0.3VCC 0.3VCC 002aae328 AC waveforms PCA9518_5 Product data sheet 0.7VCC (c) NXP B.V. 2008. All rights reserved. Rev. 05 -- 2 December 2008 11 of 21 PCA9518 NXP Semiconductors Expandable 5-channel I2C-bus hub 11. Test information VCC VCC RL PULSE GENERATOR VI VO DUT CL RT 002aad479 RL = load resistor; 1.1 k for I2C-bus, and 500 for EXPxxxn. CL = load capacitance includes jig and probe capacitance; 100 pF for I2C-bus, and 100 pF for EXPxxxn. RT = termination resistance should be equal to Zo of the pulse generators. Fig 8. Test circuit for open-drain outputs PCA9518_5 Product data sheet (c) NXP B.V. 2008. All rights reserved. Rev. 05 -- 2 December 2008 12 of 21 PCA9518 NXP Semiconductors Expandable 5-channel I2C-bus hub 12. Package outline SO20: plastic small outline package; 20 leads; body width 7.5 mm SOT163-1 D E A X c HE y v M A Z 20 11 Q A2 A (A 3) A1 pin 1 index Lp L 10 1 e bp detail X w M 0 5 10 mm scale DIMENSIONS (inch dimensions are derived from the original mm dimensions) UNIT A max. A1 A2 A3 bp c D (1) E (1) e HE L Lp Q v w y mm 2.65 0.3 0.1 2.45 2.25 0.25 0.49 0.36 0.32 0.23 13.0 12.6 7.6 7.4 1.27 10.65 10.00 1.4 1.1 0.4 1.1 1.0 0.25 0.25 0.1 0.01 0.019 0.013 0.014 0.009 0.51 0.49 0.30 0.29 0.05 0.419 0.043 0.055 0.394 0.016 inches 0.1 0.012 0.096 0.004 0.089 0.043 0.039 0.01 0.01 Z (1) 0.9 0.4 0.035 0.004 0.016 o 8 o 0 Note 1. Plastic or metal protrusions of 0.15 mm (0.006 inch) maximum per side are not included. Fig 9. REFERENCES OUTLINE VERSION IEC JEDEC SOT163-1 075E04 MS-013 JEITA EUROPEAN PROJECTION ISSUE DATE 99-12-27 03-02-19 Package outline SOT163-1 (SO20) PCA9518_5 Product data sheet (c) NXP B.V. 2008. All rights reserved. Rev. 05 -- 2 December 2008 13 of 21 PCA9518 NXP Semiconductors Expandable 5-channel I2C-bus hub TSSOP20: plastic thin shrink small outline package; 20 leads; body width 4.4 mm SOT360-1 E D A X c HE y v M A Z 11 20 Q A2 (A 3) A1 pin 1 index A Lp L 1 10 e detail X w M bp 0 2.5 5 mm scale DIMENSIONS (mm are the original dimensions) UNIT A max. A1 A2 A3 bp c D (1) E (2) e HE L Lp Q v w y Z (1) mm 1.1 0.15 0.05 0.95 0.80 0.25 0.30 0.19 0.2 0.1 6.6 6.4 4.5 4.3 0.65 6.6 6.2 1 0.75 0.50 0.4 0.3 0.2 0.13 0.1 0.5 0.2 8 o 0 o Notes 1. Plastic or metal protrusions of 0.15 mm maximum per side are not included. 2. Plastic interlead protrusions of 0.25 mm maximum per side are not included. OUTLINE VERSION SOT360-1 REFERENCES IEC JEDEC JEITA MO-153 EUROPEAN PROJECTION ISSUE DATE 99-12-27 03-02-19 Fig 10. Package outline SOT360-1 (TSSOP20) PCA9518_5 Product data sheet (c) NXP B.V. 2008. All rights reserved. Rev. 05 -- 2 December 2008 14 of 21 PCA9518 NXP Semiconductors Expandable 5-channel I2C-bus hub 13. Soldering of SMD packages This text provides a very brief insight into a complex technology. A more in-depth account of soldering ICs can be found in Application Note AN10365 "Surface mount reflow soldering description". 13.1 Introduction to soldering Soldering is one of the most common methods through which packages are attached to Printed Circuit Boards (PCBs), to form electrical circuits. The soldered joint provides both the mechanical and the electrical connection. There is no single soldering method that is ideal for all IC packages. Wave soldering is often preferred when through-hole and Surface Mount Devices (SMDs) are mixed on one printed wiring board; however, it is not suitable for fine pitch SMDs. Reflow soldering is ideal for the small pitches and high densities that come with increased miniaturization. 13.2 Wave and reflow soldering Wave soldering is a joining technology in which the joints are made by solder coming from a standing wave of liquid solder. The wave soldering process is suitable for the following: * Through-hole components * Leaded or leadless SMDs, which are glued to the surface of the printed circuit board Not all SMDs can be wave soldered. Packages with solder balls, and some leadless packages which have solder lands underneath the body, cannot be wave soldered. Also, leaded SMDs with leads having a pitch smaller than ~0.6 mm cannot be wave soldered, due to an increased probability of bridging. The reflow soldering process involves applying solder paste to a board, followed by component placement and exposure to a temperature profile. Leaded packages, packages with solder balls, and leadless packages are all reflow solderable. Key characteristics in both wave and reflow soldering are: * * * * * * Board specifications, including the board finish, solder masks and vias Package footprints, including solder thieves and orientation The moisture sensitivity level of the packages Package placement Inspection and repair Lead-free soldering versus SnPb soldering 13.3 Wave soldering Key characteristics in wave soldering are: * Process issues, such as application of adhesive and flux, clinching of leads, board transport, the solder wave parameters, and the time during which components are exposed to the wave * Solder bath specifications, including temperature and impurities PCA9518_5 Product data sheet (c) NXP B.V. 2008. All rights reserved. Rev. 05 -- 2 December 2008 15 of 21 PCA9518 NXP Semiconductors Expandable 5-channel I2C-bus hub 13.4 Reflow soldering Key characteristics in reflow soldering are: * Lead-free versus SnPb soldering; note that a lead-free reflow process usually leads to higher minimum peak temperatures (see Figure 11) than a SnPb process, thus reducing the process window * Solder paste printing issues including smearing, release, and adjusting the process window for a mix of large and small components on one board * Reflow temperature profile; this profile includes preheat, reflow (in which the board is heated to the peak temperature) and cooling down. It is imperative that the peak temperature is high enough for the solder to make reliable solder joints (a solder paste characteristic). In addition, the peak temperature must be low enough that the packages and/or boards are not damaged. The peak temperature of the package depends on package thickness and volume and is classified in accordance with Table 6 and 7 Table 6. SnPb eutectic process (from J-STD-020C) Package thickness (mm) Package reflow temperature (C) Volume (mm3) < 350 350 < 2.5 235 220 2.5 220 220 Table 7. Lead-free process (from J-STD-020C) Package thickness (mm) Package reflow temperature (C) Volume (mm3) < 350 350 to 2000 > 2000 < 1.6 260 260 260 1.6 to 2.5 260 250 245 > 2.5 250 245 245 Moisture sensitivity precautions, as indicated on the packing, must be respected at all times. Studies have shown that small packages reach higher temperatures during reflow soldering, see Figure 11. PCA9518_5 Product data sheet (c) NXP B.V. 2008. All rights reserved. Rev. 05 -- 2 December 2008 16 of 21 PCA9518 NXP Semiconductors Expandable 5-channel I2C-bus hub maximum peak temperature = MSL limit, damage level temperature minimum peak temperature = minimum soldering temperature peak temperature time 001aac844 MSL: Moisture Sensitivity Level Fig 11. Temperature profiles for large and small components For further information on temperature profiles, refer to Application Note AN10365 "Surface mount reflow soldering description". 14. Abbreviations Table 8. Abbreviations Acronym Description CDM Charged-Device Model BiCMOS Bipolar Complementary Metal-Oxide Semiconductor DUT Device Under Test ESD ElectroStatic Discharge HBM Human Body Model I/O Input/Output I2C-bus Inter-Integrated Circuit bus MM Machine Model RC Resistor Capacitor network SMBus System Management Bus PCA9518_5 Product data sheet (c) NXP B.V. 2008. All rights reserved. Rev. 05 -- 2 December 2008 17 of 21 PCA9518 NXP Semiconductors Expandable 5-channel I2C-bus hub 15. Revision history Table 9. Revision history Document ID Release date Data sheet status Change notice Supersedes PCA9518_5 20081202 Product data sheet - PCA9518_4 Modifications: * The format of this data sheet has been redesigned to comply with the new identity guidelines of NXP Semiconductors. * * * Legal texts have been adapted to the new company name where appropriate. * Figure 6 "Bus waveforms": Section 6.1 "Enable": added new 3rd paragraph Figure 5 "Typical application: multiple expandable 5-channel I2C-bus hubs": added 2nd paragraph below drawing. - changed symbol from "tst" to "tstretch" - changed symbol from "tr1" to "tPHL1" - changed symbol from "tr2" to "tPHL2" - changed symbol from "tEr1" to "tPLH2, tPLH1" * Table 3 "Limiting values": - changed symbol/parameter from "VCC to GND, supply voltage range VCC" to "VCC, supply voltage" (and placed "VCC to GND" in Conditions column) - changed symbol/parameter from "Vbus, voltage range I2C-bus, SCL or SDA" to "VI2C-bus, I2C-bus voltage" (and placed "SCL or SDA" in Conditions column) - changed symbol/parameter from "I, DC current (any pin)" to "II, input current" (and placed "any pin" in Conditions column) - changed parameter for Ptot from "power dissipation" to "total power dissipation" * Table 4 "Static characteristics": - sub-section "Supplies"; symbol ICCH: changed parameter from "quiescent supply current, both channels HIGH" to "HIGH-level supply current"; moved "both channels HIGH" to Conditions column - sub-section "Supplies"; symbol ICCL: changed parameter from "quiescent supply current, both channels LOW" to "LOW-level supply current"; moved "both channels LOW" to Conditions column - sub-section "Supplies"; symbol ICCLc: changed parameter from "quiescent supply current in contention" to "contention LOW-level supply current" - sub-section "Input SCL; input/output SDA", symbol used for parameter "input leakage current" changed from "II" to "ILI" - sub-section "Input SCL; input/output SDA", symbol VOL-VILc: parameter changed from "LOW level input voltage below output LOW level voltage" to "difference between LOW-level output and LOW-level input voltage contention" - (old) table note 1 is split into (new) Table note [1] and Table note [2] PCA9518_5 Product data sheet (c) NXP B.V. 2008. All rights reserved. Rev. 05 -- 2 December 2008 18 of 21 PCA9518 NXP Semiconductors Expandable 5-channel I2C-bus hub Table 9. Revision history ...continued Document ID Modifications: (continued) Release date * Data sheet status Change notice Supersedes Table 5 "Dynamic characteristics": - symbol/parameter "tPHLs, Propagation delay SDA to SDAn or SCL to SCLn" changed to "tPHL, HIGH to LOW propagation delay" (moved "SDA to SDAn or SCL to SCLn" to Conditions column) - symbol/parameter "tPLHs, Propagation delay SDA to SDAn or SCL to SCLn" changed to "tPLH, HIGH to LOW propagation delay" (moved "SDA to SDAn or SCL to SCLn" to Conditions column) - symbol/parameter "tPHLE1s, Propagation delay EXPSDA1 to SDA or EXPSCL1 to SCL" changed to "tPHL1, HIGH to LOW propagation delay 1" (moved "EXPSDA1 to SDA or EXPSCL1 to SCL" to Conditions column) - symbol/parameter "tPLHE1s, Propagation delay EXPSDA1 to SDA or EXPSCL1 to SCL" changed to "tPLH1, LOW to HIGH propagation delay 1" (moved "EXPSDA1 to SDA or EXPSCL1 to SCL" to Conditions column) - symbol/parameter "tPLHE2s, Propagation delay EXPSDA2 to SDA or EXPSCL2 to SCL" changed to "tPLH2, LOW to HIGH propagation delay 2" (moved "EXPSDA2 to SDA or EXPSCL2 to SCL" to Conditions column) - symbol/parameter "tTHLs, Transition time, SDA/SCL" changed to "tTHL, HIGH to LOW transition time" (moved "SDA, SCL" to Conditions column) - symbol/parameter "tTLHs, Transition time, SDA/SCL" changed to "tTLH, LOW to HIGH transition time" (moved "SDA, SCL" to Conditions column) - symbol/parameter "tSET, Enable to Start condition" changed to "tsu, set-up time" (moved "enable to START condition" to Conditions column) - symbol/parameter "tHOLD, Enable after Stop condition" changed to "th, hold time" (moved "enable to START condition" to Conditions column) * Figure 7 "AC waveforms": timing symbols updated as per symbol/parameter changes detailed above for Table 5 "Dynamic characteristics" PCA9518_4 20040929 (9397 750 14109) Product data sheet - PCA9518_3 PCA9518_3 20040624 (9397 750 13253) Product data sheet - PCA9518_2 PCA9518_2 20031110 (9397 750 12295) Product data ECN 853-2364 30410 PCA9518_1 dated 2003 Oct 03 PCA9518_1 20020820 (9397 750 10258) Product data ECN 853-2364 28791 dated 2002 Aug 20 PCA9518_5 Product data sheet (c) NXP B.V. 2008. All rights reserved. Rev. 05 -- 2 December 2008 19 of 21 PCA9518 NXP Semiconductors Expandable 5-channel I2C-bus hub 16. Legal information 16.1 Data sheet status Document status[1][2] Product status[3] Definition Objective [short] data sheet Development This document contains data from the objective specification for product development. Preliminary [short] data sheet Qualification This document contains data from the preliminary specification. Product [short] data sheet Production This document contains the product specification. [1] Please consult the most recently issued document before initiating or completing a design. [2] The term `short data sheet' is explained in section "Definitions". [3] The product status of device(s) described in this document may have changed since this document was published and may differ in case of multiple devices. The latest product status information is available on the Internet at URL http://www.nxp.com. 16.2 Definitions Draft -- The document is a draft version only. The content is still under internal review and subject to formal approval, which may result in modifications or additions. NXP Semiconductors does not give any representations or warranties as to the accuracy or completeness of information included herein and shall have no liability for the consequences of use of such information. Short data sheet -- A short data sheet is an extract from a full data sheet with the same product type number(s) and title. A short data sheet is intended for quick reference only and should not be relied upon to contain detailed and full information. For detailed and full information see the relevant full data sheet, which is available on request via the local NXP Semiconductors sales office. In case of any inconsistency or conflict with the short data sheet, the full data sheet shall prevail. 16.3 Disclaimers General -- Information in this document is believed to be accurate and reliable. However, NXP Semiconductors does not give any representations or warranties, expressed or implied, as to the accuracy or completeness of such information and shall have no liability for the consequences of use of such information. Right to make changes -- NXP Semiconductors reserves the right to make changes to information published in this document, including without limitation specifications and product descriptions, at any time and without notice. This document supersedes and replaces all information supplied prior to the publication hereof. Suitability for use -- NXP Semiconductors products are not designed, authorized or warranted to be suitable for use in medical, military, aircraft, space or life support equipment, nor in applications where failure or malfunction of an NXP Semiconductors product can reasonably be expected to result in personal injury, death or severe property or environmental damage. NXP Semiconductors accepts no liability for inclusion and/or use of NXP Semiconductors products in such equipment or applications and therefore such inclusion and/or use is at the customer's own risk. Applications -- Applications that are described herein for any of these products are for illustrative purposes only. NXP Semiconductors makes no representation or warranty that such applications will be suitable for the specified use without further testing or modification. Limiting values -- Stress above one or more limiting values (as defined in the Absolute Maximum Ratings System of IEC 60134) may cause permanent damage to the device. Limiting values are stress ratings only and operation of the device at these or any other conditions above those given in the Characteristics sections of this document is not implied. Exposure to limiting values for extended periods may affect device reliability. Terms and conditions of sale -- NXP Semiconductors products are sold subject to the general terms and conditions of commercial sale, as published at http://www.nxp.com/profile/terms, including those pertaining to warranty, intellectual property rights infringement and limitation of liability, unless explicitly otherwise agreed to in writing by NXP Semiconductors. In case of any inconsistency or conflict between information in this document and such terms and conditions, the latter will prevail. No offer to sell or license -- Nothing in this document may be interpreted or construed as an offer to sell products that is open for acceptance or the grant, conveyance or implication of any license under any copyrights, patents or other industrial or intellectual property rights. 16.4 Trademarks Notice: All referenced brands, product names, service names and trademarks are the property of their respective owners. I2C-bus -- logo is a trademark of NXP B.V. 17. Contact information For more information, please visit: http://www.nxp.com For sales office addresses, please send an email to: salesaddresses@nxp.com PCA9518_5 Product data sheet (c) NXP B.V. 2008. All rights reserved. Rev. 05 -- 2 December 2008 20 of 21 PCA9518 NXP Semiconductors Expandable 5-channel I2C-bus hub 18. Contents 1 2 3 4 5 5.1 5.2 6 6.1 6.2 6.3 7 8 9 10 11 12 13 13.1 13.2 13.3 13.4 14 15 16 16.1 16.2 16.3 16.4 17 18 General description . . . . . . . . . . . . . . . . . . . . . . 1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Ordering information . . . . . . . . . . . . . . . . . . . . . 2 Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Pinning information . . . . . . . . . . . . . . . . . . . . . . 4 Pinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Pin description . . . . . . . . . . . . . . . . . . . . . . . . . 4 Functional description . . . . . . . . . . . . . . . . . . . 5 Enable. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Expansion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 I2C-bus systems . . . . . . . . . . . . . . . . . . . . . . . . 5 Application design-in information . . . . . . . . . . 6 Limiting values. . . . . . . . . . . . . . . . . . . . . . . . . . 9 Static characteristics. . . . . . . . . . . . . . . . . . . . 10 Dynamic characteristics . . . . . . . . . . . . . . . . . 11 Test information . . . . . . . . . . . . . . . . . . . . . . . . 12 Package outline . . . . . . . . . . . . . . . . . . . . . . . . 13 Soldering of SMD packages . . . . . . . . . . . . . . 15 Introduction to soldering . . . . . . . . . . . . . . . . . 15 Wave and reflow soldering . . . . . . . . . . . . . . . 15 Wave soldering . . . . . . . . . . . . . . . . . . . . . . . . 15 Reflow soldering . . . . . . . . . . . . . . . . . . . . . . . 16 Abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Revision history . . . . . . . . . . . . . . . . . . . . . . . . 18 Legal information. . . . . . . . . . . . . . . . . . . . . . . 20 Data sheet status . . . . . . . . . . . . . . . . . . . . . . 20 Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Disclaimers . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Trademarks . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Contact information. . . . . . . . . . . . . . . . . . . . . 20 Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Please be aware that important notices concerning this document and the product(s) described herein, have been included in section `Legal information'. (c) NXP B.V. 2008. All rights reserved. For more information, please visit: http://www.nxp.com For sales office addresses, please send an email to: salesaddresses@nxp.com Date of release: 2 December 2008 Document identifier: PCA9518_5