PART NUMBER DATA SHEET E1SAA12-30.000M TR SVHC 161 Dec 17, 2014 ITEM DESCRIPTION Quartz Crystal Resonator HC49/UP Short 2 Pad Surface Mount (SMD) 3.2mm Height Metal Resistance Weld Seal 30.000MHz 50ppm at 25C, 100ppm over 0C to +70C 12pF Parallel Resonant ELECTRICAL SPECIFICATIONS Nominal Frequency 30.000MHz Frequency Tolerance/Stability 50ppm at 25C, 100ppm over 0C to +70C Aging at 25C 5ppm/year Maximum Load Capacitance 12pF Parallel Resonant Shunt Capacitance 7pF Maximum Equivalent Series Resistance 40 Ohms Maximum Mode of Operation AT-Cut Fundamental Drive Level 1mWatt Maximum Storage Temperature Range -40C to +125C Insulation Resistance 500 Megaohms Minimum (Measured at 100Vdc) ENVIRONMENTAL & MECHANICAL SPECIFICATIONS ESD Susceptibility MIL-STD-883, Method 3015, Class 1, HBM: 1500V Fine Leak Test MIL-STD-883, Method 1014, Condition A Flammability UL94-V0 Gross Leak Test MIL-STD-883, Method 1014, Condition C Mechanical Shock MIL-STD-202, Method 213, Condition C Moisture Resistance MIL-STD-883, Method 1004 Moisture Sensitivity J-STD-020, MSL1 Resistance to Soldering Heat MIL-STD-202, Method 210, Condition K Resistance to Solvents MIL-STD-202, Method 215 Solderability MIL-STD-883, Method 2003 Temperature Cycling MIL-STD-883, Method 1010, Condition B Vibration MIL-STD-883, Method 2007, Condition A www.ecliptek.com | Specification Subject to Change Without Notice | Revision G 10/08/2012 | Page 1 of 5 Ecliptek Corporation 3545 Cadillac Ave., Costa Mesa, CA 92626 1-800-ECLIPTEK or 714.433.1200 PART NUMBER DATA SHEET E1SAA12-30.000M TR MECHANICAL DIMENSIONS (all dimensions in millimeters) LINE MARKING 1 3.20 MAX E30.000M E=Ecliptek Designator 13.30 MAX 0.50 MIN (x2) 4.88 0.20 4.85 MAX 0.80 0.30 (x2) 11.60 MAX NOTE: Coplanarity 0.360 MAX Suggested Solder Pad Layout All Dimensions in Millimeters 5.5 (X2) 2.0 (X2) 4.0 Solder Land (X2) All Tolerances are 0.1 www.ecliptek.com | Specification Subject to Change Without Notice | Revision G 10/08/2012 | Page 2 of 5 Ecliptek Corporation 3545 Cadillac Ave., Costa Mesa, CA 92626 1-800-ECLIPTEK or 714.433.1200 PART NUMBER DATA SHEET E1SAA12-30.000M TR Tape & Reel Dimensions Quantity Per Reel: 1,000 units All Dimensions in Millimeters Compliant to EIA-481 4.00 0.10 0.60 MAX DIA 1.50 +0.10/-0.00 0.10 MAX 2.00 0.10 1.75 0.10 11.50 0.10 24.00 0.30 B0 DIA 1.50 MIN 12.00 0.10 A0 K0 Direction of Unreeling 1.50 MIN 37.00 MAX DIA 40 MIN Access Hole at Slot Location 360 MAX DIA 50 MIN DIA 20.20 MIN DIA 13.00 0.20 2.50 MIN Width 10 MIN Depth Tape slot in Core for Tape Start 24.00 +2.00/-0.00 www.ecliptek.com | Specification Subject to Change Without Notice | Revision G 10/08/2012 | Page 3 of 5 3545 Cadillac Ave., Costa Mesa, CA 92626 1-800-ECLIPTEK or 714.433.1200 PART NUMBER DATA SHEET E1SAA12-30.000M TR Recommended Solder Reflow Methods Critical Zone TL to T P Temperature (T) TP Ramp-up Ramp-down TL TS Max TS Min tL t S Preheat t 25C to Peak High Temperature Infrared/Convection TS MAX to TL (Ramp-up Rate) Preheat - Temperature Minimum (TS MIN) - Temperature Typical (TS TYP) - Temperature Maximum (TS MAX) - Time (tS MIN) Ramp-up Rate (TL to TP) Time Maintained Above: - Temperature (TL) - Time (tL) Peak Temperature (TP) Target Peak Temperature (TP Target) Time within 5C of actual peak (tp) Ramp-down Rate Time 25C to Peak Temperature (t) Moisture Sensitivity Level Time (t) tP 3C/Second Maximum 150C 175C 200C 60 - 180 Seconds 3C/Second Maximum 217C 60 - 150 Seconds 260C Maximum for 10 Seconds Maximum 250C +0/-5C 20 - 40 Seconds 6C/Second Maximum 8 Minutes Maximum Level 1 www.ecliptek.com | Specification Subject to Change Without Notice | Revision G 10/08/2012 | Page 4 of 5 Ecliptek Corporation 3545 Cadillac Ave., Costa Mesa, CA 92626 1-800-ECLIPTEK or 714.433.1200 PART NUMBER DATA SHEET E1SAA12-30.000M TR Recommended Solder Reflow Methods Critical Zone TL to T P Temperature (T) TP Ramp-up Ramp-down TL TS Max TS Min tL t S Preheat t 25C to Peak Low Temperature Infrared/Convection 245C TS MAX to TL (Ramp-up Rate) Preheat - Temperature Minimum (TS MIN) - Temperature Typical (TS TYP) - Temperature Maximum (TS MAX) - Time (tS MIN) Ramp-up Rate (TL to TP) Time Maintained Above: - Temperature (TL) - Time (tL) Peak Temperature (TP) Target Peak Temperature (TP Target) Time within 5C of actual peak (tp) Ramp-down Rate Time 25C to Peak Temperature (t) Moisture Sensitivity Level Time (t) tP 5C/Second Maximum N/A 150C N/A 30 - 60 Seconds 5C/Second Maximum 150C 200 Seconds Maximum 245C Maximum 245C Maximum 2 Times / 230C Maximum 1 Time 10 Seconds Maximum 2 Times / 80 Seconds Maximum 1 Time 5C/Second Maximum N/A Level 1 Low Temperature Manual Soldering 185C Maximum for 10 Seconds Maximum, 2 times Maximum. High Temperature Manual Soldering 260C Maximum for 5 Seconds Maximum, 2 times Maximum. www.ecliptek.com | Specification Subject to Change Without Notice | Revision G 10/08/2012 | Page 5 of 5 Ecliptek Corporation 3545 Cadillac Ave., Costa Mesa, CA 92626 1-800-ECLIPTEK or 714.433.1200