CAT4238 High Efficiency 10 LED Boost Converter Description The CAT4238 is a DC/DC step-up converter that delivers an accurate constant current ideal for driving LEDs. Operation at a fixed switching frequency of 1 MHz allows the device to be used with small value external ceramic capacitors and inductor. LEDs connected in series are driven with a regulated current set by the external resistor R1. LED currents up to 40 mA can be supported over a wide range of input supply voltages up to 5.5 V, making the device ideal for battery-powered applications. The CAT4238 high-voltage output stage is perfect for driving mid-size and large panel displays containing up to ten white LEDs in series. LED dimming can be done by using a DC voltage, a logic signal, or a pulse width modulation (PWM) signal. The shutdown input pin allows the device to be placed in power-down mode with "zero" quiescent current. In addition to thermal protection and overload current limiting, the device also enters a very low power operating mode during "Open LED" fault conditions. The device is housed in a low profile (1 mm max height) 5-lead thin SOT23 package for space critical applications. 5 1 TSOT-23 TD SUFFIX CASE 419AE PIN CONNECTIONS 1 VIN SW GND SHDN FB (Top View) MARKING DIAGRAM Features * * * * * * * * * * * * http://onsemi.com Drives High Voltage LED Strings (38 V) Up to 87% Efficiency Low Quiescent Ground Current 0.6 mA Adjustable Output Current 1 MHz Fixed Frequency Low Noise Operation Soft Start "In-rush" Current Limiting Shutdown Current Less than 1 mA Open LED Overvoltage Protection Automatic Shutdown at 1.9 V (UVLO) Thermal Overload Protection Thin SOT23 5-lead (1 mm Max Height) These Devices are Pb-Free, Halogen Free/BFR Free and are RoHS Compliant MUYM MU = Specific Device Code Y = Production Year (Last Digit) M = Production Month (1-9, A, B, C) ORDERING INFORMATION Device CAT4238TD-GT3 Package Shipping TSOT-23 (Pb-Free) Green* 3,000/ Tape & Reel * Lead Finish NiPdAu Applications * * * * GPS Navigation Systems Portable Media Players Handheld Devices, Digital Cameras Portable Game Machines (c) Semiconductor Components Industries, LLC, 2010 February, 2010 - Rev. 4 1 Publication Order Number: CAT4238/D CAT4238 L VIN D 47 mH C1 4.7 mF C2 SW VIN VOUT 0.22 mF CAT4238 OFF ON SHDN GND FB VFB = 300 mV 20 mA R1 15 W L: Sumida CDC5D23B-470 D: Central CMDSH05-4 C2: Taiyo Yuden UMK212BJ224 (rated 50 V) Figure 1. Typical Application Circuit Table 1. ABSOLUTE MAXIMUM RATINGS Ratings Units VIN, FB voltage Parameters -0.3 to +7 V SHDN voltage -0.3 to +7 V up to 60 V Storage Temperature Range -65 to +160 _C Junction Temperature Range -40 to +150 _C 300 _C SW voltage (Note 1) Lead Temperature Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect device reliability. 1. The SW pin voltage is rated up to 39 V for external continuous DC voltage. Table 2. RECOMMENDED OPERATING CONDITIONS Parameters VIN SW pin voltage Ambient Temperature Range NOTE: Typical application circuit with external components is shown above. http://onsemi.com 2 Range Units up to 5.5 V 0 to 38 V -40 to +85 _C CAT4238 Table 3. DC ELECTRICAL CHARACTERISTICS (VIN = 3.6 V, ambient temperature of 25C (over recommended operating conditions unless otherwise specified)) Symbol Parameter Test Conditions Min Typ Max Units IQ Operating Current VFB = 0.2 V VFB = 0.4 V (not switching) 0.6 0.1 1.5 0.6 mA ISD Shutdown Current VSHDN = 0 V 0.1 1 mA VFB FB Pin Voltage 10 LEDs with ILED = 20 mA 300 315 mV IFB FB pin input leakage 1 mA ILED Programmed LED Current VIH VIL R1 = 10 W R1 = 15 W R1 = 20 W SHDN Logic High SHDN Logic Low Enable Threshold Level Shutdown Threshold Level FSW Switching Frequency DC Maximum Duty Cycle ILIM Switch Current Limit RSW Switch "On" Resistance ISW = 100 mA ILEAK Switch Leakage Current Switch Off, VSW = 5 V 285 28.5 19 14.25 30 20 15 31.5 21 15.75 mA 0.4 0.8 0.7 1.5 V 0.8 1.0 1.3 MHz VIN = 3 V 92 350 % 450 600 mA 1.0 2.0 W 1 5 mA Thermal Shutdown 150 C Thermal Hysteresis 20 C VUVLO Undervoltage Lockout (UVLO) Threshold 1.9 V VOV-SW Overvoltage Detection Threshold 40 V VOCL Output Voltage Clamp "Open LED" with VIN = 5 V Pin Description VIN is the supply input for the internal logic. The device is compatible with supply voltages down to 2.8 V and up to 5.5 V. It is recommended that a small bypass ceramic capacitor (4.7 mF) be placed between the VIN and GND pins near the device. If the supply voltage drops below 1.9 V, the device stops switching. SHDN is the shutdown logic input. When the pin is tied to a voltage lower than 0.4 V, the device is in shutdown mode, drawing nearly zero current. When the pin is connected to a voltage higher than 1.5 V, the device is enabled. GND is the ground reference pin. This pin should be connected directly to the ground place on the PCB. 43 45 48 SW pin is connected to the drain of the internal CMOS power switch of the boost converter. The inductor and the Schottky diode anode should be connected to the SW pin. Traces going to the SW pin should be as short as possible with minimum loop area. An over-voltage detection circuit is connected to the SW pin. When the voltage reaches 40 V, the device enters a low power operating mode preventing the SW voltage from exceeding the maximum rating. FB feedback pin is regulated at 0.3 V. A resistor connected between the FB pin and ground sets the LED current according to the formula: I LED + 0.3 V R1 The lower LED cathode is connected to the FB pin. Table 4. PIN DESCRIPTIONS Pin # Name 1 SW 2 GND 3 FB 4 SHDN 5 VIN V Function Switch pin. This is the drain of the internal power switch. Ground pin. Connect the pin to the ground plane. Feedback pin. Connect to the last LED cathode. Shutdown pin (Logic Low). Set high to enable the driver. Power Supply input. http://onsemi.com 3 CAT4238 Block Diagram 47 mH VIN SW C1 C2 4.7 mF 0.22 mF 1 MHz Oscillator 300 mV - A1 + Enable SHDN Thermal Shutdown & UVLO Driver + RC LED Current PWM & Logic A2 - N1 CC RS Current Sense GND - VREF + VIN Over Voltage Protection FB Figure 2. Block Diagram Device Operation The CAT4238 is a fixed frequency (1 MHz), low noise, inductive boost converter that provides a constant current with excellent line and load regulation. The device uses a high-voltage CMOS power switch between the SW pin and ground to energize the inductor. When the switch is turned off, the stored energy in the inductor is released into the load via the Schottky diode. The on/off duty cycle of the power switch is internally adjusted and controlled to maintain a constant regulated voltage of 0.3 V across the feedback resistor connected to the feedback pin (FB). The value of the resistor sets the LED current accordingly (0.3 V/R1). During the initial power-up stage, the duty cycle of the internal power switch is limited to prevent excessive in-rush currents and thereby provide a "soft-start" mode of operation. While operating from a Li-Ion battery, the device can deliver 20 mA of load current into a string of up to 10 white LEDs. For higher input voltages, the LED current can be increased. In the event of an "Open LED" fault condition, where the feedback control loop becomes open, the output voltage will continue to increase. Once this voltage exceeds 40 V, an internal protection circuit will become active and place the device into a very low power safe operating mode where only a small amount of power is transferred to the output. This is achieved by pulsing the switch once every 6 ms and keeping it on for about 1 ms. R1 15 W Thermal overload protection circuitry has been included to prevent the device from operating at unsafe junction temperatures above 150C. In the event of a thermal overload condition the device will automatically shutdown and wait till the junction temperatures cools to 130C before normal operation is resumed. Light Load Operation Under light load condition (under 2 mA) and with input voltage above 5.0 V, the CAT4238 driving 10 LEDs, the driver starts pulse skipping. Although the LED current remains well regulated, some lower frequency ripple may appear. Figure 3. Switching Waveform VIN = 5.0 V, ILED = 1.5 mA http://onsemi.com 4 CAT4238 TYPICAL CHARACTERISTICS (VIN = 3.6 V, CIN = 4.7 mF, COUT = 0.22 mF, L = 47 mH with 10 LEDs at 20 mA, TAMB = 25C, unless otherwise specified.) 2.0 VFB = 0.4 V QUIESCENT CURRENT (mA) QUIESCENT CURRENT (mA) 150 125 100 75 50 3.0 3.5 4.0 4.5 5.0 1.5 1.0 0.5 0 5.5 3.0 3.5 4.0 4.5 5.0 INPUT VOLTAGE (V) INPUT VOLTAGE (V) Figure 4. Quiescent Current vs. VIN (Not Switching) Figure 5. Quiescent Current vs. VIN (Switching) 5.5 310 303 FB PIN VOLTAGE (mV) FB PIN VOLTAGE (mV) 302 301 300 299 305 300 295 298 10 LEDs 297 -50 0 50 100 290 150 5 10 15 20 25 TEMPERATURE (C) OUTPUT CURRENT (mA) Figure 6. FB Pin Voltage vs. Temperature Figure 7. FB Pin Voltage vs. Output Current SWITCHING FREQUENCY (MHz) 1.2 SW 20V/div 1.1 Inductor Current 100mA/div 1.0 0.9 0.8 VOUT AC coupled 500mV/div 3.0 3.5 4.0 4.5 5.0 5.5 500 ns/div INPUT VOLTAGE (V) Figure 8. Switching Frequency vs. Supply Voltage Figure 9. Switching Waveforms http://onsemi.com 5 30 CAT4238 TYPICAL CHARACTERISTICS (VIN = 3.6 V, CIN = 4.7 mF, COUT = 0.22 mF, L = 47 mH with 10 LEDs at 20 mA, TAMB = 25C, unless otherwise specified.) 40 1.0 LED CURRENT (mA) 30 25 LED CURRENT VARIATION (%) R1 = 10 W VOUT = 33.8 V 35 R1 = 15 W VOUT = 33 V 20 15 R1 = 20 W VOUT = 32.5 V 10 5 0 3.0 3.5 4.0 4.5 10 LEDs @ 10 mA 3.0 3.5 4.0 4.5 5.0 INPUT VOLTAGE (V) Figure 10. LED Current vs. Input Voltage Figure 11. LED Current Regulation (10 mA) 5.5 100 90 90 EFFICIENCY (%) VIN = 5 V 80 VIN = 3.6 V 70 VOUT = 32.5 V 10 LEDs @ 15 mA 80 VOUT = 33 V 10 LEDs @ 20 mA 70 5 10 15 20 25 60 30 3.0 3.5 4.0 4.5 5.0 LED CURRENT (mA) INPUT VOLTAGE (V) Figure 12. Efficiency vs. Load Current (10 LEDs) Figure 13. Efficiency vs. Input Voltage (10 LEDs) 5.5 2.0 SWITCH RESISTANCE (W) EFFICIENCY (%) -0.5 INPUT VOLTAGE (V) 100 60 0 -1.0 5.5 5.0 0.5 1.5 1.0 0.5 0 3.0 3.5 4.0 4.5 5.0 INPUT VOLTAGE (V) Figure 14. Power-up with 10 LEDs at 20 mA Figure 15. Switch ON Resistance vs. Input Voltage http://onsemi.com 6 5.5 CAT4238 TYPICAL CHARACTERISTICS (VIN = 3.6 V, CIN = 4.7 mF, COUT = 0.22 mF, L = 47 mH with 10 LEDs at 20 mA, TAMB = 25C, unless otherwise specified.) 1.0 50 SHUTDOWN VOLTAGE (V) OUTPUT CURRENT (mA) 60 40 30 20 VOUT = 35 V 10 0 3.0 3.5 4.0 4.5 5.0 -25C 85C 0.6 125C 0.4 0.2 5.5 -40C 0.8 3.0 3.5 4.0 4.5 5.0 INPUT VOLTAGE (V) INPUT VOLTAGE (V) Figure 16. Maximum Output Current vs. Input Voltage Figure 17. Shutdown Voltage vs. Input Voltage Application Information given current. In order to achieve the best efficiency, this forward voltage should be as low as possible. The response time is also critical since the driver is operating at 1 MHz. Central Semiconductor Schottky diode CMDSH05-4 (500 mA rated) is recommended for most applications. External Component Selection Capacitors The CAT4238 only requires small ceramic capacitors of 4.7 mF on the input and 0.22 mF on the output. Under normal condition, a 4.7 mF input capacitor is sufficient. For applications with higher output power, a larger input capacitor of 10 mF may be appropriate. X5R and X7R capacitor types are ideal due to their stability across temperature range. LED Current Setting The LED current is set by the external resistor R1 connected between the feedback pin (FB) and ground. The formula below gives the relationship between the resistor and the current: R1 + Inductor A 47 mH inductor is recommended for most of the CAT4238 applications. In cases where the efficiency is critical, inductances with lower series resistance are preferred. Inductors with current rating of 300 mA or higher are recommended for most applications. Sumida CDC5D23B-470 47 mH inductor has a rated current of 490 mA and a series resistance (D.C.R.) of 420 mW typical. 0.3 V current LED Table 5. RESISTOR R1 AND LED CURRENT LED Current (mA) R1 (W) 5 60 10 30 15 20 20 15 25 12 30 10 Schottky Diode The current rating of the Schottky diode must exceed the peak current flowing through it. The Schottky diode performance is rated in terms of its forward voltage at a http://onsemi.com 7 CAT4238 Open LED Protection In the event of an "Open LED" fault condition, the CAT4238 will continue to boost the output voltage with maximum power until the output voltage reaches approximately 40 V. Once the output exceeds this level, the internal circuitry immediately places the device into a very low power mode where the total input power is limited to about 6 mW (about 1.6 mA input current with a 3.6 V supply). The SW pin clamps at a voltage below its maximum rating of 60 V. There is no need to use an external zener diode between Vout and the FB pin. A 50 V rated C2 capacitor is required to prevent any overvoltage damage in the open LED condition. C1 SW VIN SUPPLY CURRENT (mA) 2.0 1.0 3.0 3.5 4.0 4.5 5.0 5.5 Figure 20. Open LED Supply Current vs. VIN without Zener C2 4.7 mF 3.0 INPUT VOLTAGE (V) VOUT 47 mH 4.0 0 Schottky 100 V (Central CMSH1-100) L VIN 5.0 0.22 mF 55 OFF ON SHDN GND FB OUTPUT VOLTAGE (V) CAT4238 VFB = 300 mV R1 15 W Figure 18. Open LED Protection without Zener 50 45 40 35 3.0 3.5 4.0 4.5 5.0 5.5 SW 10 V/div INPUT VOLTAGE (V) Figure 21. Open LED Output Voltage vs. VIN without Zener 2 ms/div Figure 19. Open LED Switching Waveforms without Zener http://onsemi.com 8 CAT4238 Dimming Control There are several methods available to control the LED brightness. VIN SW CAT4238 PWM Signal on the SHDN Pin SHDN GND FB LED brightness dimming can be done by applying a PWM signal to the SHDN input. The LED current is repetitively turned on and off, so that the average current is proportional to the duty cycle. A 100% duty cycle, with SHDN always high, corresponds to the LEDs at nominal current. Figure 22 shows a 1 kHz signal with a 50% duty cycle applied to the SHDN pin. The recommended PWM frequency range is from 100 Hz to 2 kHz. PWM Signal 2.5 V 3.73 kW 3.1 kW RA RB 0V C1 VFB = 300 mV 1 kW LED Current R2 i R1 15 W 0.22 mF Figure 23. Circuit for Filtered PWM Signal A PWM signal at 0 V DC, or a 0% duty cycle, results in a max LED current of about 22 mA. A PWM signal with a 93% duty cycle or more, results in an LED current of 0 mA. LED CURRENT (mA) 25 20 15 10 5 Figure 22. Switching Waveform with 1 kHz PWM on SHDN 0 0 10 20 30 40 50 60 70 80 90 100 PWM DUTY CYCLE (%) Filtered PWM Signal A filtered PWM signal used as a variable DC voltage can control the LED current. Figure 23 shows the PWM control circuitry connected to the CAT4238 FB pin. The PWM signal has a voltage swing of 0 V to 2.5 V. The LED current can be dimmed within a range from 0 mA to 20 mA. The PWM signal frequency can vary from very low frequency up to 100 kHz. Figure 24. Filtered PWM Dimming (0 V to 2.5 V) http://onsemi.com 9 CAT4238 Board Layout The CAT4238 is a high-frequency switching regulator. The traces that carry the high-frequency switching current have to be carefully layout on the board in order to minimize EMI, ripple and noise in general. The thicker lines on Figure 25 show the switching current path. All these traces have to be short and wide enough to minimize the parasitic inductance and resistance. The loop shown on Figure 25 corresponds to the current path when the CAT4238 internal switch is closed. On Figure 26 is shown the current loop, when the CAT4238 switch is open. Both loop areas should be as small as possible. Capacitor C1 has to be placed as close as possible to the VIN pin and GND. The capacitor C2 has to be connected separately to the top LED anode. A ground plane under the CAT4238 allows for direct connection of the capacitors to ground. The resistor R1 must be connected directly to the GND pin of the CAT4238 and not shared with the switching current loops and any other components. Figure 25. Closed-switch Current Loop Figure 26. Open-switch Current Loop Figure 27. Recommended PCB Layout http://onsemi.com 10 CAT4238 PACKAGE DIMENSIONS TSOT-23, 5 LEAD CASE 419AE-01 ISSUE O SYMBOL D MIN NOM A1 0.01 0.05 0.10 A2 0.80 0.87 0.90 b 0.30 c 0.12 A e E1 1.00 0.45 0.15 D 2.90 BSC E 2.80 BSC E1 1.60 BSC E MAX e 0.20 0.95 TYP L 0.30 0.40 L1 0.60 REF L2 0.25 BSC 0 0.50 8 TOP VIEW A2 A b q L A1 c L1 SIDE VIEW END VIEW Notes: (1) All dimensions are in millimeters. Angles in degrees. (2) Complies with JEDEC MO-193. http://onsemi.com 11 L2 CAT4238 Example of Ordering Information (Note 4) Prefix Device # Suffix CAT 4238 TD Company ID (Optional) Product Number 4238 -G T3 Lead Finish G: NiPdAu Tape & Reel (Note 6) T: Tape & Reel 3: 3,000 / Reel Package TD: Thin SOT-23 (Lead-free, Halogen-free) 2. 3. 4. 5. 6. All packages are RoHS-compliant (Lead-free, Halogen-free). The standard lead finish is NiPdAu. The device used in the above example is a CAT4238TD-GT3 (TSOT-23, NiPdAu, Tape & Reel, 3,000/Reel). For additional package and temperature options, please contact your nearest ON Semiconductor Sales office. For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D. ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. "Typical" parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303-675-2175 or 800-344-3860 Toll Free USA/Canada Fax: 303-675-2176 or 800-344-3867 Toll Free USA/Canada Email: orderlit@onsemi.com N. American Technical Support: 800-282-9855 Toll Free USA/Canada Europe, Middle East and Africa Technical Support: Phone: 421 33 790 2910 Japan Customer Focus Center Phone: 81-3-5773-3850 http://onsemi.com 12 ON Semiconductor Website: www.onsemi.com Order Literature: http://www.onsemi.com/orderlit For additional information, please contact your local Sales Representative CAT4238/D