August 2010 Doc ID 7019 Rev 9 1/30
1
M48T37Y
M48T37V
5.0 or 3.3 V, 256 Kbit (32 Kbit x 8) TIMEKEEPER® SRAM
Features
Integrated ultra low power SRAM, real-time
clock, power-fail control circuit, and battery
Frequency test output for real-time clock
software calibration
Automatic power-fail chip deselect and WRITE
protection
Watchdog timer
WRITE protect voltage
(VPFD = Power-fail deselect voltage):
–M48T37Y: V
CC = 4.5 to 5.5 V
4.2 V VPFD 4.5 V
–M48T37V: V
CC = 3.0 to 3.6 V
2.7 V VPFD 3.0 V
Packaging includes a 44-lead SOIC and
SNAPHAT® top (to be ordered separately)
SOIC package provides direct connection for a
SNAPHAT® top which contains the battery and
crystal
Microprocessor power-on reset (valid even
during battery backup mode)
Programmable alarm output active in the
battery backup mode
Battery low flag
RoHS compliant
Lead-free second level interconnect
44
1
SNAPHAT® (SH)
Battery/crystal
SOH44 (MH)
44-pin SOIC
www.st.com
Contents M48T37Y, M48T37V
2/30 Doc ID 7019 Rev 9
Contents
1 Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
2 Operation modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
2.1 READ mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
2.2 WRITE mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
2.3 Data retention mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
3 Clock operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
3.1 Reading the clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
3.2 Setting the clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
3.3 Stopping and starting the oscillator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
3.4 Setting the alarm clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
3.5 Calibrating the clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
3.6 Watchdog timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
3.7 Power-on reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
3.8 Programmable interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
3.9 Battery low flag . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
3.10 Initial power-on defaults . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
3.11 VCC noise and negative going transients . . . . . . . . . . . . . . . . . . . . . . . . . 18
4 Maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
5 DC and AC parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
6 Package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
7 Part numbering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
8 Environmental information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
9 Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
M48T37Y, M48T37V List of tables
Doc ID 7019 Rev 9 3/30
List of tables
Table 1. Signal names . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Table 2. Operating modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Table 3. READ mode AC characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Table 4. WRITE mode AC characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Table 5. Register map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Table 6. Alarm repeat modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Table 7. Default values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Table 8. Absolute maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Table 9. Operating and AC measurement conditions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Table 10. Capacitance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Table 11. DC characteristics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Table 12. Power down/up AC characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Table 13. Power down/up trip points DC characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Table 14. SOH44 – 44-lead plastic small outline, 4-socket SNAPHAT®, package mechanical data . 24
Table 15. SH – 4-pin SNAPHAT® housing for 48 mAh battery & crystal, package mechanical data . 25
Table 16. SH – 4-pin SNAPHAT® housing for 120 mAh battery & crystal, package mechanical data 26
Table 17. Ordering information scheme . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Table 18. SNAPHAT® battery table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Table 19. Document revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
List of figures M48T37Y, M48T37V
4/30 Doc ID 7019 Rev 9
List of figures
Figure 1. Logic diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Figure 2. SOIC connections. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Figure 3. Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Figure 4. READ mode AC waveforms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Figure 5. WRITE enable controlled, WRITE AC waveform . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Figure 6. Chip enable controlled, WRITE AC waveforms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Figure 7. Alarm interrupt reset waveform. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Figure 8. Backup mode alarm waveforms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Figure 9. Supply voltage protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Figure 10. Crystal accuracy across temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Figure 11. Clock calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Figure 12. AC testing load circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Figure 13. Power down/up mode AC waveforms. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Figure 14. SOH44 – 44-lead plastic small outline, 4-socket SNAPHAT® outline. . . . . . . . . . . . . . . . . 24
Figure 15. SH – 4-pin SNAPHAT® housing for 48 mAh battery & crystal, pack. outline . . . . . . . . . . . 25
Figure 16. SH – 4-pin SNAPHAT® housing for 120 mAh battery & crystal, pack. outline . . . . . . . . . . 26
Figure 17. Recycling symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
M48T37Y, M48T37V Description
Doc ID 7019 Rev 9 5/30
1 Description
The M48T37Y/V TIMEKEEPER® RAM is a 32 Kb x 8 non-volatile static RAM and real-time
clock. The monolithic chip is available in a special package which provides a highly
integrated battery-backed memory and real-time clock solution.
The 44-lead, 330 mil SOIC package provides sockets with gold-plated contacts at both ends
for direct connection to a separate SNAPHAT housing containing the battery and crystal.
The unique design allows the SNAPHAT® battery/crystal package to be mounted on top of
the SOIC package after the completion of the surface mount process.
Insertion of the SNAPHAT housing after reflow prevents potential battery and crystal
damage due to the high temperatures required for device surface-mounting. The SNAPHAT
housing is keyed to prevent reverse insertion.
The SOIC and battery packages are shipped separately in plastic anti-static tubes or in tape
& reel form. For the 44-lead SOIC, the battery/crystal package (e.g., SNAPHAT) part
number is “M4T28-BR12SH” or “M4T32-BR12SH”.
Caution: Do not place the SNAPHAT battery/crystal top in conductive foam, as this will drain the
lithium button-cell battery.
Figure 1. Logic diagram
AI02172
8
DQ0-DQ7
W
VCC
M48T37Y
M48T37V
VSS
G
E
WDI
RST
IRQ/FT
15
A0-A14
Description M48T37Y, M48T37V
6/30 Doc ID 7019 Rev 9
Table 1. Signal names
Figure 2. SOIC connections
A0-A14 Address inputs
DQ0-DQ7 Data inputs / outputs
RST Reset output (open drain)
IRQ/FT Interrupt / frequency test output (open drain)
WDI Watchdog input
EChip enable
GOutput enable
WWRITE enable
VCC Supply voltage
VSS Ground
NC Not connected internally
AI02174
22
44
43
VSS
1
A1
A7
A4
A3
A2
A6
A5
A13
NC
A8
A9
NC
A11
G
E
VCC
M48T37Y
M48T37V
10
2
5
6
7
8
9
11
12
13
14
15
21
40
39
36
35
34
33
32
31
30
29
28
A12
A14 IRQ/FT
NC
3
4
38
37
42
41
A0
DQ0
DQ7
DQ5DQ1
DQ2
DQ3
DQ4
DQ6
16
17
18
19
20
27
26
25
24
23
WDI
NC
NC
RST
NC
NC
NC
A10
NC
NC
W
NC
NC
NC
M48T37Y, M48T37V Description
Doc ID 7019 Rev 9 7/30
Figure 3. Block diagram
AI03253
LITHIUM
CELL
OSCILLATOR AND
CLOCK CHAIN
VPFD
RSTVCC VSS
32,768 Hz
CRYSTA L
VOLTAGE SENSE
AND
SWITCHING
CIRCUITRY
16 x 8 BiPORT
SRAM ARRAY
32,752 x 8
SRAM ARRAY
A0-A14
DQ0-DQ7
E
W
G
POWER
IRQ/FT WDI
Operation modes M48T37Y, M48T37V
8/30 Doc ID 7019 Rev 9
2 Operation modes
As Figure 3 on page 7 shows, the static memory array and the quartz controlled clock
oscillator of the M48T37Y/V are integrated on one silicon chip. The memory locations that
provide user accessible BYTEWIDE™ clock information are in the bytes with addresses
7FF1 and 7FF9h-7FFFh (located in Table 5 on page 13). The clock locations contain the
century, year, month, date, day, hour, minute, and second in 24-hour BCD format.
Corrections for 28, 29 (leap year - valid until the year 2100), 30, and 31 day months are
made automatically.
Byte 7FF8h is the clock control register. This byte controls user access to the clock
information and also stores the clock calibration setting.
Byte 7FF7h contains the watchdog timer setting. The watchdog timer redirects an out-of-
control microprocessor and provides a reset or interrupt to it. Bytes 7FF2h-7FF5h are
reserved for clock alarm programming. These bytes can be used to set the alarm. This will
generate an active low signal on the IRQ/FT pin when the alarm bytes match the date,
hours, minutes, and seconds of the clock. The eight clock bytes are not the actual clock
counters themselves; they are memory locations consisting of BiPORT™ READ/WRITE
memory cells. The M48T37Y/V includes a clock control circuit which updates the clock bytes
with current information once per second. The information can be accessed by the user in
the same manner as any other location in the static memory array.
The M48T37Y/V also has its own power-fail detect circuit. The control circuitry constantly
monitors the single VCC supply for an out of tolerance condition. When VCC is out of
tolerance, the circuit write protects the SRAM, providing a high degree of data security in the
midst of unpredictable system operation brought on by low VCC. As VCC falls below the
battery backup switchover voltage (VSO), the control circuitry connects the battery which
maintains data and clock operation until valid power returns.
Table 2. Operating modes
Note: X = VIH or VIL; VSO = Battery backup switchover voltage.
2.1 READ mode
The M48T37Y/V is in the READ mode whenever WRITE enable (W) is high and chip enable
(E) is low. The unique address specified by the 15 address inputs defines which one of the
32,752 bytes of data is to be accessed. Valid data will be available at the data I/O pins within
address access time (tAVQV) after the last address input signal is stable, providing that the E
and output enable (G) access times are also satisfied. If the E and G access times are not
Mode VCC E G W DQ0-DQ7 Power
Deselect
4.5 to 5.5 V
or
3.0 to 3.6 V
VIH X X High Z Standby
WRITE VIL XV
IL DIN Active
READ VIL VIL VIH DOUT Active
READ VIL VIH VIH High Z Active
Deselect VSO to VPFD (min)(1)
1. See Table on page 23 for details.
X X X High Z CMOS standby
Deselect VSO(1) X X X High Z Battery backup mode
M48T37Y, M48T37V Operation modes
Doc ID 7019 Rev 9 9/30
met, valid data will be available after the latter of the chip enable access time (tELQV) or
output enable access time (tGLQV).
The state of the eight three-state data I/O signals is controlled by E and G. If the outputs are
activated before tAVQV, the data lines will be driven to an indeterminate state until tAVQV.
If the address inputs are changed while E and G remain active, output data will remain valid
for output data hold time (tAXQX) but will be indeterminate until the next address access.
Figure 4. READ mode AC waveforms
Note: WRITE enable (W) = high.
AI00925
tAVAV
tAVQV tAXQX
tELQV
tELQX
tEHQZ
tGLQV
tGLQX
tGHQZ
VALID
A0-A14
E
G
DQ0-DQ7
VALID
Table 3. READ mode AC characteristics
Symbol Parameter(1)
1. Valid for ambient operating temperature: TA = 0 to 70 °C or –40 to 85 °C; VCC = 4.5 to 5.5 V or 3.0 to 3.6 V
(except where noted).
M48T37Y M48T37V
Unit–70 –100
Min Max Min Max
tAVAV READ cycle time 70 100 ns
tAVQV Address valid to output valid 70 100 ns
tELQV Chip enable low to output valid 70 100 ns
tGLQV Output enable low to output valid 35 50 ns
tELQX(2)
2. CL = 5 pF.
Chip enable low to output transition 5 10 ns
tGLQX(2) Output enable low to output transition 5 5 ns
tEHQZ(2) Chip enable high to output Hi-Z 25 50 ns
tGHQZ(2) Output enable high to output Hi-Z 25 40 ns
tAXQX Address transition to output transition 10 10 ns
Operation modes M48T37Y, M48T37V
10/30 Doc ID 7019 Rev 9
2.2 WRITE mode
The M48T37Y/V is in the WRITE mode whenever W and E are low. The start of a WRITE is
referenced from the latter occurring falling edge of W or E. A WRITE is terminated by the
earlier rising edge of W or E. The addresses must be held valid throughout the cycle. E or W
must return high for a minimum of tEHAX from chip enable or tWHAX from WRITE enable prior
to the initiation of another READ or WRITE cycle. Data-in must be valid tDVWH prior to the
end of WRITE and remain valid for tWHDX afterward. G should be kept high during WRITE
cycles to avoid bus contention; however, if the output bus has been activated by a low on E
and G, a low on W will disable the outputs tWLQZ after W falls.
Figure 5. WRITE enable controlled, WRITE AC waveform
Figure 6. Chip enable controlled, WRITE AC waveforms
AI00926
tAVAV
tWHAX
tDVWH
DATA INPUT
A0-A14
E
W
DQ0-DQ7
VALID
tAVWH
tAVEL
tWLWH
tAVWL
tWLQZ
tWHDX
tWHQX
AI00927
tAVAV
tEHAX
tDVEH
A0-A14
E
W
DQ0-DQ7
VALID
tAVEH
tAVEL
tAVWL
tELEH
tEHDX
DATA INPUT
M48T37Y, M48T37V Operation modes
Doc ID 7019 Rev 9 11/30
Table 4. WRITE mode AC characteristics
2.3 Data retention mode
With valid VCC applied, the M48T37Y/V operates as a conventional BYTEWIDE™ static
RAM. Should the supply voltage decay, the RAM will automatically power-fail deselect, write
protecting itself when VCC falls within the VPFD (max), VPFD (min) window. All outputs
become high impedance, and all inputs are treated as “Don't care.
Note: A power failure during a WRITE cycle may corrupt data at the currently addressed location,
but does not jeopardize the rest of the RAM's content. At voltages below VPFD (min), the
user can be assured the memory will be in a write protected state, provided the VCC fall time
is not less than tF
.
The M48T37Y/V may respond to transient noise spikes on VCC that reach into the deselect
window during the time the device is sampling VCC. Therefore, decoupling of the power
supply lines is recommended. When VCC drops below VSO, the control circuit switches
power to the internal battery which preserves data and powers the clock. The internal button
cell will maintain data in the M48T37Y/V for an accumulated period of at least 7 years at
room temperature when VCC is less than VSO. As system power returns and VCC rises
above VSO, the battery is disconnected and the power supply is switched to external VCC.
Normal RAM operation can resume tREC after VCC reaches VPFD (max).
For more information on battery storage life refer to the application note AN1012.
Symbol Parameter(1)
1. Valid for ambient operating temperature: TA = 0 to 70 °C or –40 to 85 °C; VCC = 4.5 to 5.5 V or 3.0 to 3.6 V
(except where noted).
M48T37Y M48T37V
Unit–70 –100
Min Max Min Max
tAVAV WRITE cycle time 70 100 ns
tAVWL Address valid to WRITE enable low 0 0 ns
tAVEL Address valid to chip enable low 0 0 ns
tWLWH WRITE enable pulse width 50 80 ns
tELEH Chip enable low to chip enable high 55 80 ns
tWHAX WRITE enable high to address transition 0 10 ns
tEHAX Chip enable high to address transition 0 10 ns
tDVWH Input valid to WRITE enable high 30 50 ns
tDVEH Input valid to chip enable high 30 50 ns
tWHDX WRITE enable high to input transition 5 5 ns
tEHDX Chip enable high to input transition 5 5 ns
tWLQZ(2)(3)
2. CL = 5 pF.
3. If E goes low simultaneously with W going low, the outputs remain in the high impedance state.
WRITE enable low to output Hi-Z 25 50 ns
tAVWH Address valid to WRITE enable high 60 80 ns
tAVEH Address valid to chip enable high 60 80 ns
tWHQX(2)(3) WRITE enable high to output transition 5 10 ns
Clock operations M48T37Y, M48T37V
12/30 Doc ID 7019 Rev 9
3 Clock operations
3.1 Reading the clock
Updates to the TIMEKEEPER® registers should be halted before clock data is read to
prevent reading data in transition. The BiPORT™ TIMEKEEPER cells in the RAM array are
only data registers and not the actual clock counters, so updating the registers can be halted
without disturbing the clock itself.
Updating is halted when a '1' is written to the READ bit, D6 in the control register 7FF8h. As
long as a '1' remains in that position, updating is halted. After a halt is issued, the registers
reflect the count; that is, the day, date, and the time that were current at the moment the halt
command was issued.
All of the TIMEKEEPER registers are updated simultaneously. A halt will not interrupt an
update in progress. Updating will resume within a second after the bit is reset to a '0.'
3.2 Setting the clock
Bit D7 of the control register (7FF8h) is the WRITE bit. Setting the WRITE bit to a '1,' like the
READ bit, halts updates to the TIMEKEEPER registers. The user can then load them with
the correct day, date, and time data in 24-hour BCD format (see Table 5 on page 13).
Resetting the WRITE bit to a '0' then transfers the values of all time registers (7FF1h,
7FF9h-7FFFh) to the actual TIMEKEEPER counters and allows normal operation to
resume. After the WRITE bit is reset, the next clock update will occur in approximately one
second.
Note: Upon power-up following a power failure, both the WRITE bit and the READ bit will be reset
to '0.'
3.3 Stopping and starting the oscillator
The oscillator may be stopped at any time. If the device is going to spend a significant
amount of time on the shelf, the oscillator can be turned off to minimize current drain on the
battery. The STOP bit is the MSB of the seconds register. Setting it to a '1' stops the
oscillator. When reset to a '0,' the M48T37Y/V oscillator starts within one second.
Note: It is not necessary to set the WRITE bit when setting or resetting the FREQUENCY TEST
bit (FT) or the STOP bit (ST).
M48T37Y, M48T37V Clock operations
Doc ID 7019 Rev 9 13/30
Table 5. Register map
Keys:
S = Sign bit
FT = Frequency test bit
R = READ bit
W = WRITE bit
ST = Stop bit
0 = Must be set to '0'
BL = Battery low flag (read only)
BMB0-BMB4 = Watchdog multiplier bits
AFE = Alarm flag enable flag
RB0-RB1 = Watchdog resolution bits
WDS = Watchdog steering bit
ABE = Alarm in battery backup mode enable bit
RPT1-RPT4 = Alarm repeat mode bits
WDF = Watchdog flag (read only)
AF = Alarm flag (read only)
Z = '0' and are read only
Address
Data Function/range
BCD format
D7 D6 D5 D4 D3 D2 D1 D0
7FFFh 10 years Year Year 00-99
7FFEh 0 0 0 10 M Month Month 01-12
7FFDh 0 0 10 date Date: Day of month Date 01-31
7FFCh 0 FT 0 0 0 Day of week Day 01-7
7FFBh 0 0 10 hours Hours Hours 00-23
7FFAh 0 10 minutes Minutes Min 00-59
7FF9h ST 10 seconds Seconds Sec 00-59
7FF8h W R S Calibration Control
7FF7h WDS BMB4 BMB3 BMB2 BMB1 BMB0 RB1 RB0 Watchdog
7FF6h AFE 0 ABE 0 0 0 0 0 Interrupts
7FF5h RPT4 0 AIarm 10 date Alarm date Alarm date 01-31
7FF4h RPT3 0 AIarm 10 hours Alarm hours Alarm hour 00-23
7FF3h RPT2 Alarm 10 minutes Alarm minutes Alarm min 00-59
7FF2h RPT1 Alarm 10 seconds Alarm seconds Alarm sec 00-59
7FF1h 1000 year 100 year Century 00-99
7FF0h WDF AF Z BL Z Z Z Z Flags
Clock operations M48T37Y, M48T37V
14/30 Doc ID 7019 Rev 9
3.4 Setting the alarm clock
Registers 7FF5h-7FF2h contain the alarm settings. The alarm can be configured to go off at
a predetermined time on a specific day of the month or repeat every day, hour, minute, or
second. It can also be programmed to go off while the M48T37Y/V is in the battery backup
mode of operation to serve as a system wake-up call.
RPT1-RPT4 put the alarm in the repeat mode of operation. Ta b l e 6 shows the possible
configurations. Codes not listed in the table default to the once per second mode to quickly
alert the user of an incorrect alarm setting.
Note: User must transition address (or toggle chip enable) to see flag bit change.
When the clock information matches the alarm clock settings based on the match criteria
defined by RPT1-RPT4, AF is set. If AFE is also set, the alarm condition activates the
IRQ/FT pin. To disable alarm, write '0' to the alarm date registers and RPT1-4. The alarm
flag and the IRQ/FT output are cleared by a READ to the flags register as shown in Figure 7.
A subsequent READ of the flags register is necessary to see that the value of the alarm flag
has been reset to '0.'
The IRQ/FT pin can also be activated in the battery backup mode. The IRQ/FT will go low if
an alarm occurs and both the alarm in battery backup mode enable (ABE) and the AFE are
set. The ABE and AFE bits are reset during power-up, therefore an alarm generated during
power-up will only set AF. The user can read the flag register at system boot-up to
determine if an alarm was generated while the M48T37Y/V was in the deselect mode during
power-up. Figure 8 illustrates the backup mode alarm timing.
Figure 7. Alarm interrupt reset waveform
Table 6. Alarm repeat modes
RPT4 RPT3 RPT2 RPT1 Alarm activated
1 1 1 1 Once per second
1 1 1 0 Once per minute
1 1 0 0 Once per hour
1 0 0 0 Once per day
0 0 0 0 Once per month
AI01677B
A0-A14
ACTIVE FLAG BIT
ADDRESS 7FF0h
IRQ/FT
15ns Min
M48T37Y, M48T37V Clock operations
Doc ID 7019 Rev 9 15/30
Figure 8. Backup mode alarm waveforms
3.5 Calibrating the clock
The M48T37Y/V is driven by a quartz controlled oscillator with a nominal frequency of
32,768 Hz. The devices are tested not to exceed ±35 ppm (parts per million) oscillator
frequency error at 25 °C, which equates to about ±1.53 minutes per month. With the
calibration bits properly set, the accuracy of each M48T37Y/V improves to better than
+1/–2 ppm at 25 °C.
The oscillation rate of any crystal changes with temperature (see Figure 10 on page 19).
Most clock chips compensate for crystal frequency and temperature shift error with
cumbersome trim capacitors. The M48T37Y/V design, however, employs periodic counter
correction. The calibration circuit adds or subtracts counts from the oscillator divider circuit
at the divide by 256 stage, as shown in Figure 11 on page 19. The number of times pulses
are blanked (subtracted, negative calibration) or split (added, positive calibration) depends
upon the value loaded into the five-bit calibration byte found in the control register. Adding
counts speeds the clock up, subtracting counts slows the clock down.
The calibration byte occupies the five lower order bits (D4-D0) in the control register 7FF8h.
These bits can be set to represent any value between 0 and 31 in binary form. Bit D5 is the
sign bit; '1' indicates positive calibration, '0' indicates negative calibration. Calibration occurs
within a 64 minute cycle. The first 62 minutes in the cycle may, once per minute, have one
second either shortened by 128 or lengthened by 256 oscillator cycles. If a binary '1' is
loaded into the register, only the first 2 minutes in the 64 minute cycle will be modified; if a
binary 6 is loaded, the first 12 will be affected, and so on.
Therefore, each calibration step has the effect of adding 512 or subtracting 256 oscillator
cycles for every 125, 829, 120 (64 minutes x 60 seconds/minute x 32,768 cycles/second)
actual oscillator cycles, that is +4.068 or –2.034 ppm of adjustment per calibration step in
the calibration register. Assuming that the oscillator is in fact running at exactly 32,768 Hz,
each of the 31 increments in the calibration byte would represent +10.7 or –5.35 seconds
per month which corresponds to a total range of +5.5 or –2.75 minutes per month.
AI03254B
VCC
IRQ/FT
tREC
VPFD (max)
VPFD (min)
ABE, AFE bit in Interrupt Register
AF bit in Flags Register
HIGH-Z
VSO
HIGH-Z
Clock operations M48T37Y, M48T37V
16/30 Doc ID 7019 Rev 9
Two methods are available for ascertaining how much calibration a given M48T37Y/V may
require. The first involves simply setting the clock, letting it run for a month and comparing it
to a known accurate reference (like WWW broadcasts). While that may seem crude, it
allows the designer to give the end user the ability to calibrate his clock as his environment
may require, even after the final product is packaged in a non-user serviceable enclosure.
All the designer has to do is provide a simple utility that accesses the calibration byte.
The second approach is better suited to a manufacturing environment, and involves the use
of the IRQ/FT pin. The pin will toggle at 512 Hz when the stop bit (ST, D7 of 7FF9h) is '0' the
frequency test bit (FT, D6 of 7FFCh) is '1,' the alarm flag enable bit (AFE, D7 of 7FF6h) is '0,'
and the watchdog steering bit (WDS, D7 of 7FF7h) is '1' or the watchdog register is reset
(7FF7h=0).
Any deviation from 512 Hz indicates the degree and direction of oscillator frequency shift at
the test temperature. For example, a reading of 512.01024 Hz would indicate a +20 ppm
oscillator frequency error, requiring a –10(WR001010) to be loaded into the calibration byte
for correction.
Note: Setting or changing the calibration byte does not affect the frequency test output frequency.
The IRQ/FT pin is an open drain output which requires a pull-up resistor for proper
operation. A 500-10 kΩ resistor is recommended in order to control the rise time. The FT bit
is cleared on power-down.
For more information on calibration, see the application note AN934, “TIMEKEEPER
calibration.
3.6 Watchdog timer
The watchdog timer can be used to detect an out-of-control microprocessor. The user
programs the watchdog timer by setting the desired amount of time-out into the eight-bit
watchdog register, address 7FF7h. The five bits (BMB4-BMB0) that store a binary multiplier
and the two lower order bits (RB1-RB0) select the resolution, where 00 = 1/16 second,
01 = 1/4second, 10 = 1 second, and 11 = 4 seconds. The amount of time-out is then
determined to be the multiplication of the five-bit multiplier value with the resolution. (For
example: writing 00001110 in the watchdog register = 3x1, or 3 seconds).
Note: Accuracy of timer is within ± the selected resolution.
If the processor does not reset the timer within the specified period, the M48T37Y/V sets the
watchdog flag (WDF) and generates a watchdog interrupt or a microprocessor reset. WDF
is reset by reading the flags register (Address 7FF0h).
Note: User must transition address (or toggle chip enable) to see flag bit change.
Reset will not occur unless the addresses are stable at the flag location for at least 15 ns
while the device is in the READ mode as shown in Figure 9 on page 19.
The most significant bit of the watchdog register is the watchdog steering bit. When set to a
'0,' the watchdog will activate the IRQ/FT pin when timed-out. When WDS is set to a '1,' the
watchdog will output a negative pulse on the RST pin for a duration of tREC. The watchdog
register, the FT bit, AFE bit, and ABE bit will reset to a '0' at the end of a watchdog time-out
when the WDS bit is set to a '1.'
The watchdog timer resets when the microprocessor performs a re-write of the watchdog
register or an edge transition (low to high / high to low) on the WDI pin occurs. The timeout
period then starts over.
M48T37Y, M48T37V Clock operations
Doc ID 7019 Rev 9 17/30
The watchdog timer is disabled by writing a value of 00000000 to the eight bits in the
watchdog register. Should the watchdog timer time out, a value of 00h needs to be written to
the watchdog register in order to clear the IRQ/FT pin.
The watchdog function is automatically disabled upon power-down and the watchdog
register is cleared. If the watchdog function is set to output to the IRQ/FT pin and the
frequency test function is activated, the watchdog or alarm function prevails and the
frequency test function is denied. The WDI pin should be connected to VSS if not used.
3.7 Power-on reset
The M48T37Y/V continuously monitors VCC. When VCC falls to the power fail detect trip
point, the RST pulls low (open drain) and remains low on power-up for tREC after VCC
passes VPFD. RST is valid for all VCC conditions. The RST pin is an open drain output and
an appropriate resistor to VCC should be chosen to control rise time (see Figure 13 on
page 22).
3.8 Programmable interrupts
The M48T37Y/V provides two programmable interrupts: an alarm and a watchdog. When an
interrupt condition occurs, the M48T37Y/V sets the appropriate flag bit in the flag register
7FF0h. The interrupt enable bits (AFE and ABE) in 7FF6h and the watchdog steering
(WDS) bit in 7FF7h allow the interrupt to activate the IRQ/FT pin.
The alarm flag and the IRQ/FT output are cleared by a READ to the flags register. An
interrupt condition reset will not occur unless the addresses are stable at the flag location for
at least 15 ns while the device is in the READ mode as shown in Figure 7 on page 14.
The IRQ/FT pin is an open drain output and requires a pull-up resistor (10 kΩ
recommended) to VCC. The pin remains in the high impedance state unless an interrupt
occurs or the frequency test mode is enabled.
Clock operations M48T37Y, M48T37V
18/30 Doc ID 7019 Rev 9
3.9 Battery low flag
The M48T37Y/V automatically performs periodic battery voltage monitoring upon power-up.
The battery low flag (BL), bit D4 of the flags register 7FF0h, will be asserted high if the
SNAPHAT® battery is found to be less than approximately 2.5 V. The BL flag will remain
active until completion of battery replacement and subsequent battery low monitoring tests
during the next power-up sequence.
If a battery low is generated during a power-up sequence, this indicates the battery voltage
is below 2.5 V (approximately), which may be insufficient to maintain data integrity. Data
should be considered suspect and verified as correct. A fresh battery should be installed.
The SNAPHAT top may be replaced while VCC is applied to the device.
Note: This will cause the clock to lose time during the interval the battery/crystal is removed.
Battery monitoring is a useful technique only when performed periodically. The M48T37Y/V
only monitors the battery when a nominal VCC is applied to the device. Thus applications
which require extensive durations in the battery back-up mode should be powered-up
periodically (at least once every few months) in order for this technique to be beneficial.
Additionally, if a battery low is indicated, data integrity should be verified upon power-up via
a checksum or other technique.
3.10 Initial power-on defaults
Upon application of power to the device, the following register bits are set to a '0' state:
WDS; BMB0-BMB4; RB0-RB1; AFE; ABE; W; R; and FT (see Ta b l e 7 ).
Table 7. Default values
3.11 VCC noise and negative going transients
ICC transients, including those produced by output switching, can produce voltage
fluctuations, resulting in spikes on the VCC bus. These transients can be reduced if
capacitors are used to store energy which stabilizes the VCC bus. The energy stored in the
bypass capacitors will be released as low going spikes are generated or energy will be
absorbed when overshoots occur. A ceramic bypass capacitor value of 0.1 µF (as shown in
Figure 9) is recommended in order to provide the needed filtering.
In addition to transients that are caused by normal SRAM operation, power cycling can
generate negative voltage spikes on VCC that drive it to values below VSS by as much as
Condition W R FT AFE ABE Watchdog
register(1)
1. WDS, BMB0-BMB4, RBO, RB1.
Initial power-up
(Battery attach for SNAPHAT®)(2)
2. State of other control bits undefined.
00000 0
Subsequent power-up / RESET(3)
3. State of other control bits remains unchanged.
00000 0
Power-down(4)
4. Assuming these bits set to '1' prior to power-down.
00011 0
M48T37Y, M48T37V Clock operations
Doc ID 7019 Rev 9 19/30
one volt. These negative spikes can cause data corruption in the SRAM while in battery
backup mode. To protect from these voltage spikes, it is recommended to connect a
Schottky diode from VCC to VSS (cathode connected to VCC, anode to VSS). Schottky diode
1N5817 is recommended for through hole and MBRS120T3 is recommended for surface
mount.
Figure 9. Supply voltage protection
Figure 10. Crystal accuracy across temperature
Figure 11. Clock calibration
AI02169
VCC
0.1µF DEVICE
VCC
VSS
AI00999
–160
0 10203040506070
Frequency (ppm)
Temperature °C
80–10–20–30–40
–100
–120
–140
–40
–60
–80
20
0
–20
ΔF= -0.038 (T - T0)2 ± 10%
F
ppm
C2
T0 = 25 °C
AI00594B
NORMAL
POSITIVE
CALIBRATION
NEGATIVE
CALIBRATION
Maximum ratings M48T37Y, M48T37V
20/30 Doc ID 7019 Rev 9
4 Maximum ratings
Stressing the device above the rating listed in the absolute maximum ratings table may
cause permanent damage to the device. These are stress ratings only and operation of the
device at these or any other conditions above those indicated in the operating sections of
this specification is not implied. Exposure to absolute maximum rating conditions for
extended periods may affect device reliability.
Table 8. Absolute maximum ratings
Caution: Negative undershoots below –0.3 V are not allowed on any pin while in the battery backup
mode.
Caution: Do NOT wave solder SOIC to avoid damaging SNAPHAT® sockets.
Symbol Parameter Value Unit
TAAmbient operating temperature Grade 1 0 to 70 °C
Grade 6 –40 to 85 °C
TSTG
Storage temperature (VCC off,
oscillator off)
SNAPHAT®–40 to 85 °C
SOH44 55 to 150 °C
TSLD(1)
1. For SOH44 package, lead-free (Pb-free) lead finish: reflow at peak temperature of 260 °C (the time above
255 °C must not exceed 30 seconds).
Lead solder temperature for 10 seconds 260 °C
VIO Input or output voltages M48T37Y –0.3 to 7 V
M48T37V –0.3 to 4.6 V
VCC Supply voltage M48T37Y –0.3 to 7 V
M48T37V –0.3 to 4.6 V
IOOutput current 10 mA
PDPower dissipation 1 W
M48T37Y, M48T37V DC and AC parameters
Doc ID 7019 Rev 9 21/30
5 DC and AC parameters
This section summarizes the operating and measurement conditions, as well as the DC and
AC characteristics of the device. The parameters in the following DC and AC characteristic
tables are derived from tests performed under the measurement conditions listed in the
relevant tables. Designers should check that the operating conditions in their projects match
the measurement conditions when using the quoted parameters.
Table 9. Operating and AC measurement conditions
Note: Output Hi-Z is defined as the point where data is no longer driven.
Figure 12. AC testing load circuit
1. 50 pF for M48T37V.
Note: Excluding open-drain output pins
Table 10. Capacitance
Parameter M48T37Y M48T37V Unit
Supply voltage (VCC) 4.5 to 5.5 3.0 to 3.6 V
Ambient operating temperature (TA)Grade 1 0 to 70 0 to 70 °C
Grade 6 –40 to 85 –40 to 85 °C
Load capacitance (CL) 100 50 pF
Input rise and fall times 10 10 ns
Input pulse voltages 0 to 3 0 to 3 V
Input and output timing ref. voltages 1.5 1.5 V
AI02325
CL = 100pF(1)
CL includes JIG capacitance
645Ω
DEVICE
UNDER
TEST
1.75V
Symbol Parameter(1)(2)
1. Effective capacitance measured with power supply at 5 V. Sampled only, not 100% tested.
2. At 25 °C, f = 1 MHz.
Min Max Unit
CIN Input capacitance - 10 pF
CIO(3)
3. Outputs deselected.
Input / output capacitance - 10 pF
DC and AC parameters M48T37Y, M48T37V
22/30 Doc ID 7019 Rev 9
Table 11. DC characteristics
Figure 13. Power down/up mode AC waveforms
Symbol Parameter Test condition(1)
1. Valid for ambient operating temperature: TA = 0 to 70 °C or –40 to 85 °C; VCC = 4.5 to 5.5 V or 3.0 to 3.6 V (except where
noted).
M48T37Y M48T37V
Unit–70 –100
MinMaxMinMax
ILI(2)
2. WDI internally pulled down to VSS through a 100 kΩ resistor.
Input leakage current 0 V VIN VCC ±1 ±1 µA
ILO(3)
3. Outputs deselected.
Output leakage current 0 V VOUT VCC ±1 ±1 µA
ICC Supply current Outputs open 50 33 mA
ICC1 Supply current (standby) TTL E = VIH 32mA
ICC2
Supply current (standby)
CMOS E = VCC – 0.2 V 3 2 mA
VIL Input low voltage –0.3 0.8 –0.3 0.8 V
VIH Input high voltage 2.2 VCC + 0.3 2.2 VCC + 0.3 V
VOL
Output low voltage (standard) IOL = 2.1 mA 0.4 0.4 V
Output low voltage
(open drain) IOL = 10 mA 0.4 0.4 V
VOH Output high voltage IOH = –1 mA 2.4 2.4 V
AI03078
VCC
INPUTS
RST
OUTPUTS
DON'T CARE
HIGH-Z
tF
tFB
tR
tREC
tRB
tDR
VALID VALID
VPFD (max)
VPFD (min)
VSO
VALID VALID
M48T37Y, M48T37V DC and AC parameters
Doc ID 7019 Rev 9 23/30
Note: All voltages referenced to VSS.
Table 12. Power down/up AC characteristics
Symbol Parameter(1)
1. Valid for ambient operating temperature: TA = 0 to 70 °C or –40 to 85 °C; VCC = 4.5 to 5.5 V or 3.0 to 3.6 V
(except where noted).
Min Max Unit
tF(2)
2. VPFD (max) to VPFD (min) fall time of less than tF may result in deselection/write protection not occurring
until 200 µs after VCC passes VPFD (min).
VPFD (max) to VPFD (min) VCC fall time 300 µs
tFB(3)
3. VPFD (min) to VSS fall time of less than tFB may cause corruption of RAM data
VPFD (min) to VSS VCC fall time 10 µs
tRVPFD (min) to VPFD (max) VCC rise time 10 µs
tRB VSS to VPFD (min) VCC rise time 1 µs
tREC(4)
4. tREC (min) = 20 ms for industrial temperature range - grade 6 device.
VPFD (max) to RST high 40 200 ms
Table 13. Power down/up trip points DC characteristics
Symbol Parameter(1)
1. Valid for ambient operating temperature: TA = 0 to 70 °C or –40 to 85 °C; VCC = 4.5 to 5.5 V or 3.0 to 3.6 V
(except where noted).
Min Typ Max Unit
VPFD Power-fail deselect voltage M48T37Y 4.2 4.4 4.5 V
M48T37V 2.7 2.9 3.0 V
VSO Battery backup switchover voltage M48T37Y VBAT V
M48T37V VPFD100 mV V
tDR(2)
2. At 25 °C, VCC = 0 V.
Expected data retention time Grade 1 5 7 Years
Grade 6 10(3)
3. Using larger M4T32-BR12SH6 SNAPHAT® top (recommended for industrial temperature range - grade 6
device).
Years
Package mechanical data M48T37Y, M48T37V
24/30 Doc ID 7019 Rev 9
6 Package mechanical data
In order to meet environmental requirements, ST offers these devices in different grades of
ECOPACK® packages, depending on their level of environmental compliance. ECOPACK®
specifications, grade definitions and product status are available at: www.st.com.
ECOPACK® is an ST trademark.
Figure 14. SOH44 – 44-lead plastic small outline, 4-socket SNAPHAT® outline
Note: Drawing is not to scale.
Table 14. SOH44 – 44-lead plastic small outline, 4-socket SNAPHAT®, package
mechanical data
SOH-A
E
N
D
C
LA1 α
1
H
A
CP
Be
A2
eB
Symbol
mm inches
Typ Min Max Typ Min Max
A3.050.120
A1 0.05 0.36 0.002 0.014
A2 2.34 2.69 0.092 0.106
B 0.36 0.46 0.014 0.018
C 0.15 0.32 0.006 0.012
D 17.71 18.49 0.697 0.728
E 8.23 8.89 0.324 0.350
e0.81– 0.032
eB 3.20 3.61 0.126 0.142
H 11.51 12.70 0.453 0.500
L 0.41 1.27 0.016 0.050
a0°8°0°8°
N44 44
CP 0.10 0.004
M48T37Y, M48T37V Package mechanical data
Doc ID 7019 Rev 9 25/30
Figure 15. SH – 4-pin SNAPHAT® housing for 48 mAh battery & crystal, pack. outline
Note: Drawing is not to scale.
Table 15. SH – 4-pin SNAPHAT® housing for 48 mAh battery & crystal, package
mechanical data
SHTK-A
A1 A
D
E
eA
eB
A2
BL
A3
Symbol
mm inches
Typ Min Max Typ Min Max
A9.780.385
A1 6.73 7.24 0.265 0.285
A2 6.48 6.99 0.255 0.275
A3 0.38 0.015
B 0.46 0.56 0.018 0.022
D 21.21 21.84 0.835 0.860
E 14.22 14.99 0.560 0.590
eA 15.55 15.95 0.612 0.628
eB 3.20 3.61 0.126 0.142
L 2.03 2.29 0.080 0.090
Package mechanical data M48T37Y, M48T37V
26/30 Doc ID 7019 Rev 9
Figure 16. SH – 4-pin SNAPHAT® housing for 120 mAh battery & crystal, pack. outline
Note: Drawing is not to scale.
SHTK-A
A1 A
D
E
eA
eB
A2
BL
A3
Table 16. SH – 4-pin SNAPHAT® housing for 120 mAh battery & crystal, package
mechanical data
Symbol
mm inches
Typ Min Max Typ Min Max
A 10.54 0.415
A1 8.00 8.51 0.315 .0335
A2 7.24 8.00 0.285 0.315
A3 0.38 0.015
B 0.46 0.56 0.018 0.022
D 21.21 21.84 0.835 0.860
E 17.27 18.03 0.680 .0710
eA 15.55 15.95 0.612 0.628
eB 3.20 3.61 0.126 0.142
L 2.03 2.29 0.080 0.090
M48T37Y, M48T37V Part numbering
Doc ID 7019 Rev 9 27/30
7 Part numbering
Caution: Do not place the SNAPHAT battery package “M4TXX-BR12SH” in conductive foam as it will
drain the lithium button-cell battery.
For other options, or for more information on any aspect of this device, please contact the
ST sales office nearest you.
Table 17. Ordering information scheme
Example: M48T 37Y –70 MH 1 E
Device type
M48T
Supply voltage and write protect voltage
37Y = VCC = 4.5 to 5.5 V; VPFD = 4.2 to 4.5 V
37V = VCC = 3.0 to 3.6 V; VPFD = 2.7 to 3.0 V
Speed
–70 = 70 ns (37Y)
–10 = 100 ns (37V)
Package
MH(1) = SOH44
1. The SOIC package (SOH44) requires the SNAPHAT® battery package which is ordered separately under
the part number “M4TXX-BR12SH” in plastic tube or “M4TXX-BR12SHTR” in tape & reel form (see
Table ).
Temperature range
1 = 0 to 70 °C
6 = –40 to 85 °C(2)
2. Not recommended for new design. Contact ST sales office for availability.
Shipping method
blank = tubes (not for new design - use E)
E = ECOPACK® package, tubes
F = ECOPACK® package, tape & reel
TR = tape & reel (not for new design - use F)
Table 18. SNAPHAT® battery table
Part number Description Package
M4T28-BR12SH Lithium battery (48 mAh) SNAPHAT®SH
M4T32-BR12SH Lithium battery (120 mAh) SNAPHAT®SH
Environmental information M48T37Y, M48T37V
28/30 Doc ID 7019 Rev 9
8 Environmental information
Figure 17. Recycling symbols
This product contains a non-rechargeable lithium (lithium carbon monofluoride chemistry)
button cell battery fully encapsulated in the final product.
Recycle or dispose of batteries in accordance with the battery manufacturer's instructions
and local/national disposal and recycling regulations.
Please refer to the following web site address for additional information regarding
compliance statements and waste recycling.
Go to www.st.com/rtc, then select "Lithium Battery Recycling" from "Related Topics".
M48T37Y, M48T37V Revision history
Doc ID 7019 Rev 9 29/30
9 Revision history
Table 19. Document revision history
Date Revision Changes
Dec-1999 1 First issue
07-Feb-2000 2 From preliminary data to datasheet; battery low flag paragraph
changed; 100 ns speed class identifier changed (Ta b l e , 4)
11-Jul-2000 2.1 tFB changed (Tabl e ); watchdog timer paragraph changed
19-Jun-2001 3 Reformatted; added temp./voltage info. to tables (Ta b l e 1 0 , 11, , 4, , )
06-Aug-2001 3.1 Fix text for setting the alarm clock (Figure 7)
15-Jan-2002 3.2 Fix footnote numbering (Ta bl e )
20-May-2002 3.3 Modify reflow time and temperature footnote (Tab l e 8)
31-Mar-2003 4 v2.2 template applied; data retention condition updated (Ta b l e )
01-Apr-2004 5 Reformatted; updated with lead-free package information (Ta bl e 8, )
08-Feb-2006 6 New template; updated lead-free text; fixed DC characteristics (Tabl e 8,
11, )
03-Aug-2007 7 Reformatted; added lead-free second level interconnect information to
cover page and Section 6: Package mechanical data.
24-Mar-2009 8 Updated Ta bl e 8 ; Section 6: Package mechanical data; added
Section 8: Environmental information; minor reformatting.
02-Aug-2010 9 Updated Features, Section 4, Ta bl e 1 7 ; reformatted document; minor
textual changes.
M48T37Y, M48T37V
30/30 Doc ID 7019 Rev 9
Please Read Carefully:
Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST) reserve the
right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any
time, without notice.
All ST products are sold pursuant to ST’s terms and conditions of sale.
Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no
liability whatsoever relating to the choice, selection or use of the ST products and services described herein.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this
document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products
or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such
third party products or services or any intellectual property contained therein.
UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED
WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED
WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS
OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT.
UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZED ST REPRESENTATIVE, ST PRODUCTS ARE NOT
RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING
APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY,
DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE
GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER’S OWN RISK.
Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void
any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any
liability of ST.
ST and the ST logo are trademarks or registered trademarks of ST in various countries.
Information in this document supersedes and replaces all information previously supplied.
The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners.
© 2010 STMicroelectronics - All rights reserved
STMicroelectronics group of companies
Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan -
Malaysia - Malta - Morocco - Philippines - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America
www.st.com