STRATUM 3E High Stability Oven Stabilized Oscillator OH100 Series 2111 Comprehensive Drive Aurora, Illinois 60505 Phone: 630- 851- 4722 11 www.conwin.com Connor-Winfield's high stability OH100 series are exceptionally precise frequency standards, excellent for use in cellular base stations, test equipment, Synchronous Ethernet, VSAT and Stratum 3E applications These unique OCXOs and OCVCXOs provide temperature stabilities in the range of 10 ppb to 50 ppb, over the commercial, extended commercial or the industrial temperature range. Power requirements are 1.1W over the commercial temperature range and 1.5W over the industrial temperature range after warm-up. Additionally, excellent aging is achieved through the use of overtone SC cut crystals. The OH100 series is available with CMOS logic or Sinewave output along with Electronic Frequency Tuning. These oscillators provide outstanding phase noise that varies depending on frequency. Allan Variance specifications are rated for primary reference standards. Warm up times are on the order of 5 minutes to 0.10 ppm of final frequency. 32 12 CF 3 00 61 Hz 0- M 93 10 0.0 74 OH 1 28 25 94 Fax: 630- 851- 5040 Description Features * Frequency Range: 5 to 40 MHz * OCXO - Fixed Frequency * OCVCXO - Voltage Controlled Frequency * 3.3 Vdc or 5.0 Vdc Operation * Available Frequency Stabilities: 10.0 ppb, 20 ppb or 50 ppb * Available Temperature Ranges: 0 to 70C, -20 to 70C, -20 to 75C, -40 to 70C or -40 to 85C * Low Phase Noise / Phase Jitter * Output: CMOS Logic or Sinewave * Package: 1.0" x 1.0" x 0.500" * RoHS Compliant / Lead Free Ordering Information OH100Package OH100- = 1.0"x1.0"x0.5" Through Hole Package 6 10 03 C F Temperature Range Frequency Stability Supply Voltage Output Type OCXO Type 5 = 0 to 70C 6 = -40 to 85C 7 = -20 to 70C 8 = -40 to 70C 9 = -20 to 75C 10 = 10.0 ppb 20 = 20.0 ppb 50 = 50.0 ppb 03 = 3.3 Vdc 05 = 5.0 Vdc C = CMOS S = Sinewave F = Fixed Freq. V = Voltage Controlled Freq. - 010.0M Output Frequency Frequency Format -xxx.xM Min -xxx.xxxxxxM Max *Amount of numbers after the decimal point. M = MHz Example Part Number: . . Bulletin Page Revision Date Cx205 1 of 4 05 07 Dec 2012 OH100-61003CF-010.0M = 1.0" x 1.0" x 0.445" package, -40 to 85C temperature range, 10.0 ppb frequency stability, 3.3 Vdc supply voltage, CMOS square wave output, fixed output frequency OCXO, 10.0 MHz output frequency. OH100-52005CV-010.0M = 1.0" x 1.0" x 0.445" package, 0 to 70C temperature range, 20.0 ppb frequency stability, 5.0 Vdc supply voltage, CMOS square wave output, voltage controlled output frequency, OCVCXO, 10.0 MHz output frequency. OH100-71005SV-010.0M = 1.0" x 1.0" x 0.445" package, -20 to 70C temperature range, 10.0 ppb frequency stability, 5.0 Vdc supply voltage, Sinewave output, voltage controlled output frequency, OCVCXO, 10.0 MHz output frequency. Attention: System Designers please review Application Note AN2093: System Design Information and Printed Circuit Board Layout Guidelines for OCXO Oscillators. @ www.conwin.com/technologies.html Specifications subject to change without notice. All dimensions in inches. (c) Copyright 2011 The Connor-Winfield Corporation 2111 Comprehensive Drive Aurora, Illinois 60505 Phone: 630- 851- 4722 Fax: 630- 851- 5040 www.conwin.com Absolute Maximum Ratings Parameter Storage Temperature Supply Voltage - 3.3 Vdc (Vcc) Supply Voltage - 5.0 Vdc (Vcc) Control Voltage (Vc) Minimum -55 -0.5 -0.5 -0.5 Nominal - Maximum Units Notes Maximum Units Notes 125 4.5 7.0 7.0 C Vdc Vdc Vdc Operating Specifications Parameter Minimum Nominal Center Frequency: (Fo) 5 40 MHz Operating Temperature Range: Temperature Code 5 0 70 C Temperature Code 6 -40 85 C Temperature Code 7 -20 70 C Temperature Code 8 -40 70 C Temperature Code 9 -20 75 C Frequency Calibration: -0.1 0.1 ppm @ 25C Frequency Stability vs. Change in Temperature: Stability Code 10 -10.0 10.0 ppb 1 Stability Code 20 -20.0 20.0 ppb 1 Stability Code 50 -50.0 50.0 ppb 1 Frequency Stability vs. Load -2.0 2.0 ppb 5% Frequency Stability vs. Voltage -2.0 2.0 ppb 5% Aging: Daily: 5 MHz to 20 MHz -1.0 1.0 ppb/day 2 >20 MHz to 40 MHz -2.0 2.0 ppb/day 2 Aging: First Year: 5 MHz to 20 MHz -50 50 ppb >20 MHz to 40 MHz -100 100 ppb Lifetime Tolerance: (20 Years) 5 MHz to 20 MHz- -300 300 ppb 3 >20 MHz to 40 MHz -500 500 ppb 3 Supply Voltage: (Vcc) (Note: Power supply turn-on ramp time must be > 5 ms to 90% of Vcc.) Voltage Code 03 3.13 3.30 3.47 Vdc 4 Voltage Code 05 4.75 5.00 5.25 Vdc 4 Power Consumption: Turn-On 0 to 70C Models 3.00 W 5 -20 to 70C Models 3.20 W 5 -20 to 75C Models 3.30 W 5 -40 to 85C Models 3.80 W 5 Power Consumption: Steady State @ 25C 0 to 70C Models 1.10 W 5 -20 to 70C Models 1.15 W 5 -20 to 75C Models 1.20 W 5 -40 to 85C Models 1.50 W 5 Phase Jitter: (BW: 10 Hz to Fo/2) Models Fo: 5 MHz to 20 MHz 1.0 ps RMS Models Fo: >20 MHz to 40 MHz 2.0 ps RMS Short Term Allan Deviation (1s) 1.0E-11 RMS Start-Up Time: 500 ms Warm Up Time @ 25C: 5 minutes 6 Notes: 1. Referenced to the frequency measured @ 25C. 2. At time of shipment after 48 hours of operation. 3. Inclusive of calibration, operating temperature, supply voltage change, load change and 20 years aging. 4. Minimum "Power On Time" after rail rises from 0 to within +/-5% of Vcc = 1 second. Vcc ramp rate must be <0.3 volts per millisecond. 5. Measured with Vcc = Nominal, in calm air. 6. Measured @ 25C, within 100 ppb, referenced one hour after turn-on 7. To ensure proper operation of OCVCXO's the control voltage input must be biased the nominal control voltage. Failure to bias the Vc input will cause an unstable output condition.. Specifications subject to change without notice. All dimensions in inches. (c) Copyright 2011 The Connor-Winfield Corporation Bulletin Page Revision Date Cx205 2 of 4 05 07 Dec 2012 2111 Comprehensive Drive Aurora, Illinois 60505 Phone: 630- 851- 4722 Fax: 630- 851- 5040 www.conwin.com Phase Noise Characteristics Typical Phase Noise for OH100-series with CMOS Output Parameter SSB Phase Noise 5 - 12 MHz >12- 20 MHz >20 - 30 MHz >30 - 40 MHz @ 1Hz offset @ 10Hz offset @ 100Hz offset @ 1KHz offset @ 10KHz offset @ 100KHz offset -85 -115 -140 -145 -150 -150 -80 -110 -135 -140 -150 -150 -70 -100 -125 -140 -150 -150 -65 -95 -120 -140 -150 -150 Units Notes dBc/Hz dBc/Hz dBc/Hz dBc/Hz dBc/Hz dBc/Hz OCVCXO Input Characteristics (OCXO Type Code V) Parameter Control Voltage Range: 3.3 Vdc Models 5.0 Vdc Models Frequency Pullability: Input Impedance Minimum Nominal Maximum Units Notes 0.30 0.50 0.4 100K 1.65 2.50 - 3.00 4.50 - V V ppm Ohms Vcc = 3.3 Vdc Vcc = 5.0 Vdc 7 Notes CMOS Output Characteristics (Output Code C) Parameter Load Output Voltage: 3.3 Vdc Models High (Voh) Low (Vol) 5.0 Vdc Models High (Voh) Low (Vol) Duty Cycle at 50% of Vcc Rise / Fall Time: 10% to 90% Spurious Output Minimum Nominal Maximum Units 3.0 4.7 45 - 50 - 0.4 0.4 55 6 -80 V - 15 - pF V % ns dBc Sinewave Output Characteristics (Output Code S) Parameter Load Output Power Harmonics Spurious Minimum +5.0 - Nominal 50 - Maximum +10 -30 -80 Units Ohms dBm: dBc dBc Notes Package Characteristics OH100 Package Hermetically sealed, resistive welded package with grounded case. Environmental Characteristics Shock Sinusoidal Vibration Random Vibration Moisture Marking Permanency Attachment Method PCB Resistance to Solder Heat Solder Process 500 G's 1ms, Halfsine, 3 shocks per direction, per MIL-STD 202G, Method 213B Test Condition D. 0.06" D.A. or 10G's Peak, 10 to 500 Hz, per MIL-STD-202G, Method 204D, Test Condition A. 5.35 G's rms. 20 to 2000 Hz per MIL-STD-202G, Method 214,Test Condition 1A, 15 minutes each axis. 10 cycles, 95% RH, Per MIL-STD-202G, Method 112. Per MIL-STD-202G, Method 215J. Through Hole Mounted Per MIL-STD-202G, Method 210, Condition E. RoHS compliant, lead free. See solder profile. Bulletin Page Revision Date Specifications subject to change without notice. All dimensions in inches. (c) Copyright 2011 The Connor-Winfield Corporation Cx205 3 of 4 05 07 Dec 2012 2111 Comprehensive Drive Aurora, Illinois 60505 Phone: 630- 851- 4722 Fax: 630- 851- 5040 www.conwin.com Re-Stabilization Time Off Time <1 Hour <6 Hour <24 Hour 1 to 16 Days >16 Days Re stabilization Time <2 Hours * <12 Hours * <48 Hours * 48 Hours + 1/4 Off Time * <6 Days * * For a given off time, the time required to meet daily aging, short term stability requirements. Package Outline Package Marking .500 Max. (12.70mm) 1232 OH100-61003CF 10.0 MHz 123456789012 123456789012 Date Code (YYWW) Model Number Output Frequency Serial # Barcode Serial Number Dimensional Tolerance: .005 (.127mm) Keep Out Area: Under the OCXO is a keep out area, do not place any parts in this area. Attention: System Designers please review Application Note AN2093: System Design Information and Printed Circuit Board Layout Guidelines for OCXO Oscillators. @ www.conwin.com/technologies.html Test Circuit Control Voltage or N/C 10 uF to 100 uF Pin Connections Pin Connection 1: Output 2: Ground (Case) 3: Control Voltage or N/C 4: N/C 5: Supply Voltage (Vcc) N/C 15 pF 0.01 uF Solder Profile Temperature 260C CMOS Output Waveform 260C 220C 180C 90% 150C 120C 50% 10% 0 10 s Up to 120 s 60 to 90 s Typical Typical Revision 00, Revision 01, Revision 02, Revision 03, Revision 04, Revision 05, Meets IPC/JEDEC J-STD-020C New issue, 03/01/11. Updated power consumption. 07/27/11 Added sinewave models. 03/22/12 Updated marking information. 08/22/12 Added +10 dB Max to sinewave output characteristics . 09/18/12 Added application note AN2093 information. 12/07/12 Specifications subject to change without notice. All dimensions in inches. (c) Copyright 2011 The Connor-Winfield Corporation Bulletin Page Revision Date Cx205 4 of 4 05 07 Dec 2012