Features * High-performance, Low-power Atmel(R) AVR(R) 8-bit Microcontroller * Advanced RISC Architecture * * * * * * * * - 131 Powerful Instructions - Most Single-clock Cycle Execution - 32 x 8 General Purpose Working Registers - Fully Static Operation - Up to 16 MIPS Throughput at 16 MHz - On-chip 2-cycle Multiplier High Endurance Non-volatile Memory segments - 32Kbytes of In-System Self-programmable Flash program memory - 1024Bytes EEPROM - 2Kbyte Internal SRAM - Write/Erase Cycles: 10,000 Flash/100,000 EEPROM - Data retention: 20 years at 85C/100 years at 25C(1) - Optional Boot Code Section with Independent Lock Bits In-System Programming by On-chip Boot Program True Read-While-Write Operation - Programming Lock for Software Security JTAG (IEEE std. 1149.1 Compliant) Interface - Boundary-scan Capabilities According to the JTAG Standard - Extensive On-chip Debug Support - Programming of Flash, EEPROM, Fuses, and Lock Bits through the JTAG Interface Peripheral Features - Two 8-bit Timer/Counters with Separate Prescalers and Compare Modes - One 16-bit Timer/Counter with Separate Prescaler, Compare Mode, and Capture Mode - Real Time Counter with Separate Oscillator - Four PWM Channels - 8-channel, 10-bit ADC 8 Single-ended Channels 7 Differential Channels in TQFP Package Only 2 Differential Channels with Programmable Gain at 1x, 10x, or 200x - Byte-oriented Two-wire Serial Interface - Programmable Serial USART - Master/Slave SPI Serial Interface - Programmable Watchdog Timer with Separate On-chip Oscillator - On-chip Analog Comparator Special Microcontroller Features - Power-on Reset and Programmable Brown-out Detection - Internal Calibrated RC Oscillator - External and Internal Interrupt Sources - Six Sleep Modes: Idle, ADC Noise Reduction, Power-save, Power-down, Standby and Extended Standby I/O and Packages - 32 Programmable I/O Lines - 40-pin PDIP, 44-lead TQFP, and 44-pad QFN/MLF Operating Voltages - 2.7V - 5.5V for ATmega32L - 4.5V - 5.5V for ATmega32 Speed Grades - 0 - 8MHz for ATmega32L - 0 - 16MHz for ATmega32 Power Consumption at 1 MHz, 3V, 25C - Active: 1.1mA - Idle Mode: 0.35mA - Power-down Mode: < 1A 8-bit Microcontroller with 32KBytes In-System Programmable Flash ATmega32 ATmega32L Summary 2503QS-AVR-02/11 ATmega32(L) Pin Configurations Figure 1. Pinout ATmega32 PDIP (XCK/T0) PB0 (T1) PB1 (INT2/AIN0) PB2 (OC0/AIN1) PB3 (SS) PB4 (MOSI) PB5 (MISO) PB6 (SCK) PB7 RESET VCC GND XTAL2 XTAL1 (RXD) PD0 (TXD) PD1 (INT0) PD2 (INT1) PD3 (OC1B) PD4 (OC1A) PD5 (ICP1) PD6 PA0 (ADC0) PA1 (ADC1) PA2 (ADC2) PA3 (ADC3) PA4 (ADC4) PA5 (ADC5) PA6 (ADC6) PA7 (ADC7) AREF GND AVCC PC7 (TOSC2) PC6 (TOSC1) PC5 (TDI) PC4 (TDO) PC3 (TMS) PC2 (TCK) PC1 (SDA) PC0 (SCL) PD7 (OC2) PB4 (SS) PB3 (AIN1/OC0) PB2 (AIN0/INT2) PB1 (T1) PB0 (XCK/T0) GND VCC PA0 (ADC0) PA1 (ADC1) PA2 (ADC2) PA3 (ADC3) TQFP/MLF (MOSI) PB5 (MISO) PB6 (SCK) PB7 RESET VCC GND XTAL2 XTAL1 (RXD) PD0 (TXD) PD1 (INT0) PD2 PD3 PD4 PD5 PD6 PD7 VCC GND (SCL) PC0 (SDA) PC1 (TCK) PC2 (TMS) PC3 (INT1) (OC1B) (OC1A) (ICP1) (OC2) Note: Bottom pad should be soldered to ground. PA4 (ADC4) PA5 (ADC5) PA6 (ADC6) PA7 (ADC7) AREF GND AVCC PC7 (TOSC2) PC6 (TOSC1) PC5 (TDI) PC4 (TDO) 2 2503QS-AVR-02/11 ATmega32(L) Overview The Atmel(R) AVR(R) ATmega32 is a low-power CMOS 8-bit microcontroller based on the AVR enhanced RISC architecture. By executing powerful instructions in a single clock cycle, the ATmega32 achieves throughputs approaching 1 MIPS per MHz allowing the system designer to optimize power consumption versus processing speed. Block Diagram Figure 2. Block Diagram PA0 - PA7 PC0 - PC7 PORTA DRIVERS/BUFFERS PORTC DRIVERS/BUFFERS PORTA DIGITAL INTERFACE PORTC DIGITAL INTERFACE VCC GND AVCC MUX & ADC ADC INTERFACE TWI AREF PROGRAM COUNTER STACK POINTER PROGRAM FLASH SRAM TIMERS/ COUNTERS OSCILLATOR INTERNAL OSCILLATOR XTAL1 INSTRUCTION REGISTER GENERAL PURPOSE REGISTERS WATCHDOG TIMER OSCILLATOR XTAL2 X INSTRUCTION DECODER Y MCU CTRL. & TIMING RESET Z CONTROL LINES ALU INTERRUPT UNIT AVR CPU STATUS REGISTER EEPROM PROGRAMMING LOGIC SPI USART + - INTERNAL CALIBRATED OSCILLATOR COMP. INTERFACE PORTB DIGITAL INTERFACE PORTD DIGITAL INTERFACE PORTB DRIVERS/BUFFERS PORTD DRIVERS/BUFFERS PB0 - PB7 PD0 - PD7 3 2503QS-AVR-02/11 ATmega32(L) The Atmel(R) AVR(R) core combines a rich instruction set with 32 general purpose working registers. All the 32 registers are directly connected to the Arithmetic Logic Unit (ALU), allowing two independent registers to be accessed in one single instruction executed in one clock cycle. The resulting architecture is more code efficient while achieving throughputs up to ten times faster than conventional CISC microcontrollers. The ATmega32 provides the following features: 32Kbytes of In-System Programmable Flash Program memory with Read-While-Write capabilities, 1024bytes EEPROM, 2Kbyte SRAM, 32 general purpose I/O lines, 32 general purpose working registers, a JTAG interface for Boundaryscan, On-chip Debugging support and programming, three flexible Timer/Counters with compare modes, Internal and External Interrupts, a serial programmable USART, a byte oriented Two-wire Serial Interface, an 8-channel, 10-bit ADC with optional differential input stage with programmable gain (TQFP package only), a programmable Watchdog Timer with Internal Oscillator, an SPI serial port, and six software selectable power saving modes. The Idle mode stops the CPU while allowing the USART, Two-wire interface, A/D Converter, SRAM, Timer/Counters, SPI port, and interrupt system to continue functioning. The Power-down mode saves the register contents but freezes the Oscillator, disabling all other chip functions until the next External Interrupt or Hardware Reset. In Power-save mode, the Asynchronous Timer continues to run, allowing the user to maintain a timer base while the rest of the device is sleeping. The ADC Noise Reduction mode stops the CPU and all I/O modules except Asynchronous Timer and ADC, to minimize switching noise during ADC conversions. In Standby mode, the crystal/resonator Oscillator is running while the rest of the device is sleeping. This allows very fast start-up combined with low-power consumption. In Extended Standby mode, both the main Oscillator and the Asynchronous Timer continue to run. The device is manufactured using Atmel's high density nonvolatile memory technology. The Onchip ISP Flash allows the program memory to be reprogrammed in-system through an SPI serial interface, by a conventional nonvolatile memory programmer, or by an On-chip Boot program running on the AVR core. The boot program can use any interface to download the application program in the Application Flash memory. Software in the Boot Flash section will continue to run while the Application Flash section is updated, providing true Read-While-Write operation. By combining an 8-bit RISC CPU with In-System Self-Programmable Flash on a monolithic chip, the Atmel ATmega32 is a powerful microcontroller that provides a highly-flexible and cost-effective solution to many embedded control applications. The Atmel AVR ATmega32 is supported with a full suite of program and system development tools including: C compilers, macro assemblers, program debugger/simulators, in-circuit emulators, and evaluation kits. Pin Descriptions VCC Digital supply voltage. GND Ground. Port A (PA7..PA0) Port A serves as the analog inputs to the A/D Converter. Port A also serves as an 8-bit bi-directional I/O port, if the A/D Converter is not used. Port pins can provide internal pull-up resistors (selected for each bit). The Port A output buffers have symmetrical drive characteristics with both high sink and source capability. When pins PA0 to PA7 are used as inputs and are externally pulled low, they will source current if the internal pull-up resistors are activated. The Port A pins are tri-stated when a reset condition becomes active, even if the clock is not running. 4 2503QS-AVR-02/11 ATmega32(L) Port B (PB7..PB0) Port B is an 8-bit bi-directional I/O port with internal pull-up resistors (selected for each bit). The Port B output buffers have symmetrical drive characteristics with both high sink and source capability. As inputs, Port B pins that are externally pulled low will source current if the pull-up resistors are activated. The Port B pins are tri-stated when a reset condition becomes active, even if the clock is not running. Port B also serves the functions of various special features of the ATmega32 as listed on page 57. Port C (PC7..PC0) Port C is an 8-bit bi-directional I/O port with internal pull-up resistors (selected for each bit). The Port C output buffers have symmetrical drive characteristics with both high sink and source capability. As inputs, Port C pins that are externally pulled low will source current if the pull-up resistors are activated. The Port C pins are tri-stated when a reset condition becomes active, even if the clock is not running. If the JTAG interface is enabled, the pull-up resistors on pins PC5(TDI), PC3(TMS) and PC2(TCK) will be activated even if a reset occurs. The TD0 pin is tri-stated unless TAP states that shift out data are entered. Port C also serves the functions of the JTAG interface and other special features of the ATmega32 as listed on page 60. Port D (PD7..PD0) Port D is an 8-bit bi-directional I/O port with internal pull-up resistors (selected for each bit). The Port D output buffers have symmetrical drive characteristics with both high sink and source capability. As inputs, Port D pins that are externally pulled low will source current if the pull-up resistors are activated. The Port D pins are tri-stated when a reset condition becomes active, even if the clock is not running. Port D also serves the functions of various special features of the ATmega32 as listed on page 62. RESET Reset Input. A low level on this pin for longer than the minimum pulse length will generate a reset, even if the clock is not running. The minimum pulse length is given in Table 15 on page 37. Shorter pulses are not guaranteed to generate a reset. XTAL1 Input to the inverting Oscillator amplifier and input to the internal clock operating circuit. XTAL2 Output from the inverting Oscillator amplifier. AVCC AVCC is the supply voltage pin for Port A and the A/D Converter. It should be externally connected to VCC, even if the ADC is not used. If the ADC is used, it should be connected to VCC through a low-pass filter. AREF AREF is the analog reference pin for the A/D Converter. 5 2503QS-AVR-02/11 ATmega32(L) Resources A comprehensive set of development tools, application notes and datasheets are available for download on http://www.atmel.com/avr. Note: 1. Data Retention Reliability Qualification results show that the projected data retention failure rate is much less than 1 PPM over 20 years at 85C or 100 years at 25C. About Code Examples This documentation contains simple code examples that briefly show how to use various parts of the device. These code examples assume that the part specific header file is included before compilation. Be aware that not all C Compiler vendors include bit definitions in the header files and interrupt handling in C is compiler dependent. Please confirm with the C Compiler documentation for more details. 6 2503QS-AVR-02/11 ATmega32(L) Register Summary Address Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 $3F ($5F) SREG I T H S V N Z C 10 $3E ($5E) SPH - - - - SP11 SP10 SP9 SP8 12 SP4 SP3 SP2 SP1 SP0 12 - - - IVSEL IVCE 47, 67 $3D ($5D) SPL $3C ($5C) OCR0 $3B ($5B) GICR SP7 SP6 SP5 Timer/Counter0 Output Compare Register INT1 INT0 Page 82 INT2 $3A ($5A) GIFR INTF1 INTF0 INTF2 - - - - - 68 $39 ($59) TIMSK OCIE2 TOIE2 TICIE1 OCIE1A OCIE1B TOIE1 OCIE0 TOIE0 82, 112, 130 83, 112, 130 $38 ($58) TIFR OCF2 TOV2 ICF1 OCF1A OCF1B TOV1 OCF0 TOV0 $37 ($57) SPMCR SPMIE RWWSB - RWWSRE BLBSET PGWRT PGERS SPMEN 248 $36 ($56) TWCR TWINT TWEA TWSTA TWSTO TWWC TWEN - TWIE 177 $35 ($55) MCUCR SE SM2 SM1 SM0 ISC11 ISC10 ISC01 ISC00 32, 66 $34 ($54) MCUCSR JTD ISC2 - JTRF WDRF BORF EXTRF PORF 40, 67, 228 $33 ($53) TCCR0 FOC0 WGM00 COM01 COM00 WGM01 CS02 CS01 CS00 80 $32 ($52) TCNT0 $31(1) ($51)(1) OSCCAL OCDR Timer/Counter0 (8 Bits) 82 Oscillator Calibration Register 30 On-Chip Debug Register 224 $30 ($50) SFIOR ADTS2 ADTS1 ADTS0 - ACME PUD PSR2 PSR10 56,85,131,198,218 $2F ($4F) TCCR1A COM1A1 COM1A0 COM1B1 COM1B0 FOC1A FOC1B WGM11 WGM10 107 $2E ($4E) TCCR1B ICNC1 ICES1 - WGM13 WGM12 CS12 CS11 CS10 110 $2D ($4D) TCNT1H Timer/Counter1 - Counter Register High Byte 111 $2C ($4C) TCNT1L 111 $2B ($4B) OCR1AH Timer/Counter1 - Counter Register Low Byte Timer/Counter1 - Output Compare Register A High Byte $2A ($4A) OCR1AL Timer/Counter1 - Output Compare Register A Low Byte 111 $29 ($49) OCR1BH Timer/Counter1 - Output Compare Register B High Byte 111 111 $28 ($48) OCR1BL Timer/Counter1 - Output Compare Register B Low Byte 111 $27 ($47) ICR1H Timer/Counter1 - Input Capture Register High Byte 111 $26 ($46) ICR1L Timer/Counter1 - Input Capture Register Low Byte $25 ($45) TCCR2 $24 ($44) TCNT2 Timer/Counter2 (8 Bits) $23 ($43) OCR2 Timer/Counter2 Output Compare Register $22 ($42) ASSR $21 ($41) $20(2) ($40)(2) FOC2 WGM20 COM21 111 COM20 WGM21 CS22 CS21 CS20 125 127 127 - - - - AS2 TCN2UB OCR2UB TCR2UB WDTCR - - - WDTOE WDE WDP2 WDP1 WDP0 UBRRH URSEL - - - UBRR[11:8] 128 42 164 UCSRC URSEL UMSEL UPM1 UPM0 USBS UCSZ1 UCSZ0 UCPOL 162 $1F ($3F) EEARH - - - - - - EEAR9 EEAR8 19 $1E ($3E) EEARL EEPROM Address Register Low Byte $1D ($3D) EEDR EEPROM Data Register $1C ($3C) EECR - - - - EERIE EEMWE EEWE EERE $1B ($3B) PORTA PORTA7 PORTA6 PORTA5 PORTA4 PORTA3 PORTA2 PORTA1 PORTA0 64 $1A ($3A) DDRA DDA7 DDA6 DDA5 DDA4 DDA3 DDA2 DDA1 DDA0 64 64 19 19 19 $19 ($39) PINA PINA7 PINA6 PINA5 PINA4 PINA3 PINA2 PINA1 PINA0 $18 ($38) PORTB PORTB7 PORTB6 PORTB5 PORTB4 PORTB3 PORTB2 PORTB1 PORTB0 64 $17 ($37) DDRB DDB7 DDB6 DDB5 DDB4 DDB3 DDB2 DDB1 DDB0 64 $16 ($36) PINB PINB7 PINB6 PINB5 PINB4 PINB3 PINB2 PINB1 PINB0 65 $15 ($35) PORTC PORTC7 PORTC6 PORTC5 PORTC4 PORTC3 PORTC2 PORTC1 PORTC0 65 $14 ($34) DDRC DDC7 DDC6 DDC5 DDC4 DDC3 DDC2 DDC1 DDC0 65 $13 ($33) PINC PINC7 PINC6 PINC5 PINC4 PINC3 PINC2 PINC1 PINC0 65 $12 ($32) PORTD PORTD7 PORTD6 PORTD5 PORTD4 PORTD3 PORTD2 PORTD1 PORTD0 65 $11 ($31) DDRD DDD7 DDD6 DDD5 DDD4 DDD3 DDD2 DDD1 DDD0 65 PIND7 PIND6 PIND5 PIND4 PIND3 PIND2 PIND1 PIND0 $10 ($30) PIND $0F ($2F) SPDR SPI Data Register 65 138 $0E ($2E) SPSR SPIF WCOL - - - - - SPI2X 138 $0D ($2D) SPCR SPIE SPE DORD MSTR CPOL CPHA SPR1 SPR0 136 $0C ($2C) UDR $0B ($2B) UCSRA USART I/O Data Register 159 $0A ($2A) UCSRB $09 ($29) UBRRL $08 ($28) ACSR ACD ACBG $07 ($27) ADMUX REFS1 $06 ($26) ADCSRA ADEN $05 ($25) ADCH ADC Data Register High Byte 217 $04 ($24) ADCL ADC Data Register Low Byte 217 $03 ($23) TWDR Two-wire Serial Interface Data Register $02 ($22) TWAR RXC TXC UDRE FE DOR PE U2X MPCM 160 RXCIE TXCIE UDRIE RXEN TXEN UCSZ2 RXB8 TXB8 161 ACO ACI ACIE ACIC ACIS1 ACIS0 199 REFS0 ADLAR MUX4 MUX3 MUX2 MUX1 MUX0 214 ADSC ADATE ADIF ADIE ADPS2 ADPS1 ADPS0 216 USART Baud Rate Register Low Byte TWA6 TWA5 TWA4 164 179 TWA3 TWA2 TWA1 TWA0 TWGCE 179 7 2503QS-AVR-02/11 ATmega32(L) Address Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Page $01 ($21) TWSR TWS7 TWS6 TWS5 TWS4 TWS3 - TWPS1 TWPS0 178 $00 ($20) TWBR Notes: Two-wire Serial Interface Bit Rate Register 177 1. When the OCDEN Fuse is unprogrammed, the OSCCAL Register is always accessed on this address. Refer to the debugger specific documentation for details on how to use the OCDR Register. 2. Refer to the USART description for details on how to access UBRRH and UCSRC. 3. For compatibility with future devices, reserved bits should be written to zero if accessed. Reserved I/O memory addresses should never be written. 4. Some of the Status Flags are cleared by writing a logical one to them. Note that the CBI and SBI instructions will operate on all bits in the I/O Register, writing a one back into any flag read as set, thus clearing the flag. The CBI and SBI instructions work with registers $00 to $1F only. 8 2503QS-AVR-02/11 ATmega32(L) Instruction Set Summary Mnemonics Operands Description Operation Flags #Clocks ARITHMETIC AND LOGIC INSTRUCTIONS ADD Rd, Rr Add two Registers Rd Rd + Rr Z,C,N,V,H ADC Rd, Rr Add with Carry two Registers Rd Rd + Rr + C Z,C,N,V,H 1 ADIW Rdl,K Add Immediate to Word Rdh:Rdl Rdh:Rdl + K Z,C,N,V,S 2 SUB Rd, Rr Subtract two Registers Rd Rd - Rr Z,C,N,V,H 1 SUBI Rd, K Subtract Constant from Register Rd Rd - K Z,C,N,V,H 1 SBC Rd, Rr Subtract with Carry two Registers Rd Rd - Rr - C Z,C,N,V,H 1 1 SBCI Rd, K Subtract with Carry Constant from Reg. Rd Rd - K - C Z,C,N,V,H 1 SBIW Rdl,K Subtract Immediate from Word Rdh:Rdl Rdh:Rdl - K Z,C,N,V,S 2 1 AND Rd, Rr Logical AND Registers Rd Rd * Rr Z,N,V ANDI Rd, K Logical AND Register and Constant Rd Rd * K Z,N,V 1 OR Rd, Rr Logical OR Registers Rd Rd v Rr Z,N,V 1 ORI Rd, K Logical OR Register and Constant Rd Rd v K Z,N,V 1 EOR Rd, Rr Exclusive OR Registers Rd Rd Rr Z,N,V 1 COM Rd One's Complement Rd $FF - Rd Z,C,N,V 1 NEG Rd Two's Complement Rd $00 - Rd Z,C,N,V,H 1 SBR Rd,K Set Bit(s) in Register Rd Rd v K Z,N,V 1 CBR Rd,K Clear Bit(s) in Register Rd Rd * ($FF - K) Z,N,V 1 INC Rd Increment Rd Rd + 1 Z,N,V 1 DEC Rd Decrement Rd Rd - 1 Z,N,V 1 TST Rd Test for Zero or Minus Rd Rd * Rd Z,N,V 1 CLR Rd Clear Register Rd Rd Rd Z,N,V 1 SER Rd Set Register Rd $FF None 1 MUL Rd, Rr Multiply Unsigned R1:R0 Rd x Rr Z,C 2 MULS Rd, Rr Multiply Signed R1:R0 Rd x Rr Z,C 2 MULSU Rd, Rr Multiply Signed with Unsigned R1:R0 Rd x Rr Z,C 2 FMUL Rd, Rr Fractional Multiply Unsigned R1:R0 (Rd x Rr) << 1 Z,C 2 FMULS Rd, Rr Fractional Multiply Signed R1:R0 (Rd x Rr) << 1 Z,C 2 FMULSU Rd, Rr Fractional Multiply Signed with Unsigned R1:R0 (Rd x Rr) << 1 Z,C 2 Relative Jump PC PC + k + 1 None 2 Indirect Jump to (Z) PC Z None 2 3 BRANCH INSTRUCTIONS RJMP k IJMP JMP k Direct Jump PC k None RCALL k Relative Subroutine Call PC PC + k + 1 None 3 Indirect Call to (Z) PC Z None 3 ICALL Direct Subroutine Call PC k None 4 RET Subroutine Return PC Stack None 4 RETI Interrupt Return PC Stack I if (Rd = Rr) PC PC + 2 or 3 None CALL k 4 CPSE Rd,Rr Compare, Skip if Equal 1/2/3 CP Rd,Rr Compare Rd - Rr Z, N,V,C,H 1 CPC Rd,Rr Compare with Carry Rd - Rr - C Z, N,V,C,H 1 CPI Rd,K Compare Register with Immediate Rd - K Z, N,V,C,H SBRC Rr, b Skip if Bit in Register Cleared if (Rr(b)=0) PC PC + 2 or 3 None 1 1/2/3 SBRS Rr, b Skip if Bit in Register is Set if (Rr(b)=1) PC PC + 2 or 3 None 1/2/3 SBIC P, b Skip if Bit in I/O Register Cleared if (P(b)=0) PC PC + 2 or 3 None 1/2/3 SBIS P, b Skip if Bit in I/O Register is Set if (P(b)=1) PC PC + 2 or 3 None 1/2/3 BRBS s, k Branch if Status Flag Set if (SREG(s) = 1) then PCPC+k + 1 None 1/2 BRBC s, k Branch if Status Flag Cleared if (SREG(s) = 0) then PCPC+k + 1 None 1/2 BREQ k Branch if Equal if (Z = 1) then PC PC + k + 1 None 1/2 BRNE k Branch if Not Equal if (Z = 0) then PC PC + k + 1 None 1/2 BRCS k Branch if Carry Set if (C = 1) then PC PC + k + 1 None 1/2 BRCC k Branch if Carry Cleared if (C = 0) then PC PC + k + 1 None 1/2 BRSH k Branch if Same or Higher if (C = 0) then PC PC + k + 1 None 1/2 BRLO k Branch if Lower if (C = 1) then PC PC + k + 1 None 1/2 BRMI k Branch if Minus if (N = 1) then PC PC + k + 1 None 1/2 BRPL k Branch if Plus if (N = 0) then PC PC + k + 1 None 1/2 BRGE k Branch if Greater or Equal, Signed if (N V= 0) then PC PC + k + 1 None 1/2 BRLT k Branch if Less Than Zero, Signed if (N V= 1) then PC PC + k + 1 None 1/2 BRHS k Branch if Half Carry Flag Set if (H = 1) then PC PC + k + 1 None 1/2 BRHC k Branch if Half Carry Flag Cleared if (H = 0) then PC PC + k + 1 None 1/2 BRTS k Branch if T Flag Set if (T = 1) then PC PC + k + 1 None 1/2 BRTC k Branch if T Flag Cleared if (T = 0) then PC PC + k + 1 None 1/2 BRVS k Branch if Overflow Flag is Set if (V = 1) then PC PC + k + 1 None 1/2 BRVC k Branch if Overflow Flag is Cleared if (V = 0) then PC PC + k + 1 None 1/2 9 2503QS-AVR-02/11 ATmega32(L) Mnemonics Operands Description Operation Flags BRIE k Branch if Interrupt Enabled if ( I = 1) then PC PC + k + 1 None #Clocks 1/2 BRID k Branch if Interrupt Disabled if ( I = 0) then PC PC + k + 1 None 1/2 None 1 None 1 DATA TRANSFER INSTRUCTIONS MOV Rd, Rr Move Between Registers MOVW Rd, Rr Copy Register Word Rd Rr Rd+1:Rd Rr+1:Rr LDI Rd, K Load Immediate Rd K None 1 LD Rd, X Load Indirect Rd (X) None 2 LD Rd, X+ Load Indirect and Post-Inc. Rd (X), X X + 1 None 2 LD Rd, - X Load Indirect and Pre-Dec. X X - 1, Rd (X) None 2 2 LD Rd, Y Load Indirect Rd (Y) None LD Rd, Y+ Load Indirect and Post-Inc. Rd (Y), Y Y + 1 None 2 LD Rd, - Y Load Indirect and Pre-Dec. Y Y - 1, Rd (Y) None 2 LDD Rd,Y+q Load Indirect with Displacement Rd (Y + q) None 2 LD Rd, Z Load Indirect Rd (Z) None 2 LD Rd, Z+ Load Indirect and Post-Inc. Rd (Z), Z Z+1 None 2 LD Rd, -Z Load Indirect and Pre-Dec. Z Z - 1, Rd (Z) None 2 LDD Rd, Z+q Load Indirect with Displacement Rd (Z + q) None 2 2 LDS Rd, k Load Direct from SRAM Rd (k) None ST X, Rr Store Indirect (X) Rr None 2 ST X+, Rr Store Indirect and Post-Inc. (X) Rr, X X + 1 None 2 ST - X, Rr Store Indirect and Pre-Dec. X X - 1, (X) Rr None 2 ST Y, Rr Store Indirect (Y) Rr None 2 ST Y+, Rr Store Indirect and Post-Inc. (Y) Rr, Y Y + 1 None 2 ST - Y, Rr Store Indirect and Pre-Dec. Y Y - 1, (Y) Rr None 2 STD Y+q,Rr Store Indirect with Displacement (Y + q) Rr None 2 ST Z, Rr Store Indirect (Z) Rr None 2 ST Z+, Rr Store Indirect and Post-Inc. (Z) Rr, Z Z + 1 None 2 ST -Z, Rr Store Indirect and Pre-Dec. Z Z - 1, (Z) Rr None 2 STD Z+q,Rr Store Indirect with Displacement (Z + q) Rr None 2 STS k, Rr Store Direct to SRAM (k) Rr None 2 Load Program Memory R0 (Z) None 3 LPM LPM Rd, Z Load Program Memory Rd (Z) None 3 LPM Rd, Z+ Load Program Memory and Post-Inc Rd (Z), Z Z+1 None 3 Store Program Memory (Z) R1:R0 None - In Port Rd P None 1 1 SPM IN Rd, P OUT P, Rr Out Port P Rr None PUSH Rr Push Register on Stack Stack Rr None 2 POP Rd Pop Register from Stack Rd Stack None 2 BIT AND BIT-TEST INSTRUCTIONS SBI P,b Set Bit in I/O Register I/O(P,b) 1 None 2 CBI P,b Clear Bit in I/O Register I/O(P,b) 0 None 2 LSL Rd Logical Shift Left Rd(n+1) Rd(n), Rd(0) 0 Z,C,N,V 1 LSR Rd Logical Shift Right Rd(n) Rd(n+1), Rd(7) 0 Z,C,N,V 1 ROL Rd Rotate Left Through Carry Rd(0)C,Rd(n+1) Rd(n),CRd(7) Z,C,N,V 1 ROR Rd Rotate Right Through Carry Rd(7)C,Rd(n) Rd(n+1),CRd(0) Z,C,N,V 1 ASR Rd Arithmetic Shift Right Rd(n) Rd(n+1), n=0..6 Z,C,N,V 1 SWAP Rd Swap Nibbles Rd(3..0)Rd(7..4),Rd(7..4)Rd(3..0) None 1 BSET s Flag Set SREG(s) 1 SREG(s) 1 BCLR s Flag Clear SREG(s) 0 SREG(s) 1 BST Rr, b Bit Store from Register to T T Rr(b) T 1 BLD Rd, b Bit load from T to Register Rd(b) T None 1 1 SEC Set Carry C1 C CLC Clear Carry C0 C 1 SEN Set Negative Flag N1 N 1 CLN Clear Negative Flag N0 N 1 SEZ Set Zero Flag Z1 Z 1 CLZ Clear Zero Flag Z0 Z 1 SEI Global Interrupt Enable I1 I 1 CLI Global Interrupt Disable I0 I 1 1 SES Set Signed Test Flag S1 S CLS Clear Signed Test Flag S0 S 1 SEV Set Twos Complement Overflow. V1 V 1 CLV SET CLT SEH Clear Twos Complement Overflow Set T in SREG Clear T in SREG Set Half Carry Flag in SREG V0 T1 T0 H1 V T T H 1 1 1 1 10 2503QS-AVR-02/11 ATmega32(L) Mnemonics Operands CLH MCU CONTROL INSTRUCTIONS NOP SLEEP WDR BREAK Description Operation Flags Clear Half Carry Flag in SREG H0 H No Operation Sleep Watchdog Reset Break (see specific descr. for Sleep function) (see specific descr. for WDR/timer) For On-Chip Debug Only None None None None #Clocks 1 1 1 1 N/A 11 2503QS-AVR-02/11 ATmega32(L) Ordering Information Speed (MHz) 8 16 Notes: Ordering Code(2) Package(1) 2.7V - 5.5V ATmega32L-8AU ATmega32L-8AUR(3) ATmega32L-8PU ATmega32L-8MU ATmega32L-8MUR(3) 44A 44A 40P6 44M1 44M1 4.5V - 5.5V ATmega32-16AU ATmega32-16AUR(3) ATmega32-16PU ATmega32-16MU ATmega32-16MUR(3) 44A 44A 40P6 44M1 44M1 Power Supply Operational Range Industrial (-40oC to 85oC) 1. This device can also be supplied in wafer form. Please contact your local Atmel sales office for detailed ordering information and minimum quantities. 2. Pb-free packaging complies to the European Directive for Restriction of Hazardous Substances (RoHS directive). Also Halide free and fully Green. 3. Tape & Reel Package Type 44A 44-lead, 10 x 10 x 1.0mm, Thin Profile Plastic Quad Flat Package (TQFP) 40P6 40-pin, 0.600" Wide, Plastic Dual Inline Package (PDIP) 44M1 44-pad, 7 x 7 x 1.0mm, Quad Flat No-Lead/Micro Lead Frame Package (QFN/MLF) 12 2503QS-AVR-02/11 ATmega32(L) Packaging Information 44A PIN 1 IDENTIFIER PIN 1 e B E1 E D1 D C 0~7 A1 A2 A L COMMON DIMENSIONS (Unit of Measure = mm) Notes: 1. This package conforms to JEDEC reference MS-026, Variation ACB. 2. Dimensions D1 and E1 do not include mold protrusion. Allowable protrusion is 0.25 mm per side. Dimensions D1 and E1 are maximum plastic body size dimensions including mold mismatch. 3. Lead coplanarity is 0.10 mm maximum. SYMBOL MIN NOM MAX A - - 1.20 A1 0.05 - 0.15 A2 0.95 1.00 1.05 D 11.75 12.00 12.25 D1 9.90 10.00 10.10 E 11.75 12.00 12.25 E1 9.90 10.00 10.10 B 0.30 - 0.45 C 0.09 - 0.20 L 0.45 - 0.75 e NOTE Note 2 Note 2 0.80 TYP 2010-10-20 R 2325 Orchard Parkway San Jose, CA 95131 TITLE 44A, 44-lead, 10 x 10 mm Body Size, 1.0 mm Body Thickness, 0.8 mm Lead Pitch, Thin Profile Plastic Quad Flat Package (TQFP) DRAWING NO. REV. 44A C 13 2503QS-AVR-02/11 ATmega32(L) 40P6 D PIN 1 E1 A SEATING PLANE A1 L B B1 e E 0 ~ 15 C eB Notes: COMMON DIMENSIONS (Unit of Measure = mm) REF 1. This package conforms to JEDEC reference MS-011, Variation AC. 2. Dimensions D and E1 do not include mold Flash or Protrusion. Mold Flash or Protrusion shall not exceed 0.25 mm (0.010"). SYMBOL MIN NOM MAX A - - 4.826 A1 0.381 - - D 52.070 - 52.578 E 15.240 - 15.875 E1 13.462 - 13.970 B 0.356 - 0.559 B1 1.041 - 1.651 L 3.048 - 3.556 C 0.203 - 0.381 eB 15.494 - 17.526 e NOTE Note 2 Note 2 2.540 TYP 09/28/01 R 2325 Orchard Parkway San Jose, CA 95131 TITLE 40P6, 40-lead (0.600"/15.24 mm Wide) Plastic Dual Inline Package (PDIP) DRAWING NO. 40P6 REV. B 14 2503QS-AVR-02/11 ATmega32(L) 44M1 D Marked Pin# 1 ID E SEATING PLANE A1 TOP VIEW A3 A K L Pin #1 Corner D2 1 2 3 Option A SIDE VIEW Pin #1 Triangle E2 Option B K Option C b e Pin #1 Chamfer (C 0.30) Pin #1 Notch (0.20 R) BOTTOM VIEW COMMON DIMENSIONS (Unit of Measure = mm) SYMBOL MIN NOM MAX A 0.80 0.90 1.00 A1 - 0.02 0.05 A3 0.20 REF b 0.18 0.23 0.30 D 6.90 7.00 7.10 D2 5.00 5.20 5.40 E 6.90 7.00 7.10 E2 5.00 5.20 5.40 e Note: JEDEC Standard MO-220, Fig. 1 (SAW Singulation) VKKD-3. NOTE 0.50 BSC L 0.59 0.64 0.69 K 0.20 0.26 0.41 9/26/08 Package Drawing Contact: packagedrawings@atmel.com TITLE 44M1, 44-pad, 7 x 7 x 1.0 mm Body, Lead Pitch 0.50 mm, 5.20 mm Exposed Pad, Thermally Enhanced Plastic Very Thin Quad Flat No Lead Package (VQFN) GPC ZWS DRAWING NO. REV. 44M1 H 15 2503QS-AVR-02/11 ATmega32(L) Errata ATmega32, rev. A to F * * * * First Analog Comparator conversion may be delayed Interrupts may be lost when writing the timer registers in the asynchronous timer IDCODE masks data from TDI input Reading EEPROM by using ST or STS to set EERE bit triggers unexpected interrupt request. 1. First Analog Comparator conversion may be delayed If the device is powered by a slow rising VCC, the first Analog Comparator conversion will take longer than expected on some devices. Problem Fix/Workaround When the device has been powered or reset, disable then enable theAnalog Comparator before the first conversion. 2. Interrupts may be lost when writing the timer registers in the asynchronous timer The interrupt will be lost if a timer register that is synchronous timer clock is written when the asynchronous Timer/Counter register (TCNTx) is 0x00. Problem Fix/Workaround Always check that the asynchronous Timer/Counter register neither have the value 0xFF nor 0x00 before writing to the asynchronous Timer Control Register (TCCRx), asynchronousTimer Counter Register (TCNTx), or asynchronous Output Compare Register (OCRx). 3. IDCODE masks data from TDI input The JTAG instruction IDCODE is not working correctly. Data to succeeding devices are replaced by all-ones during Update-DR. Problem Fix / Workaround - If ATmega32 is the only device in the scan chain, the problem is not visible. - Select the Device ID Register of the ATmega32 by issuing the IDCODE instruction or by entering the Test-Logic-Reset state of the TAP controller to read out the contents of its Device ID Register and possibly data from succeeding devices of the scan chain. Issue the BYPASS instruction to the ATmega32 while reading the Device ID Registers of preceding devices of the boundary scan chain. - If the Device IDs of all devices in the boundary scan chain must be captured simultaneously, the ATmega32 must be the fist device in the chain. 4. Reading EEPROM by using ST or STS to set EERE bit triggers unexpected interrupt request. Reading EEPROM by using the ST or STS command to set the EERE bit in the EECR register triggers an unexpected EEPROM interrupt request. Problem Fix / Workaround Always use OUT or SBI to set EERE in EECR. 16 2503QS-AVR-02/11 ATmega32(L) Datasheet Revision History Please note that the referring page numbers in this section are referred to this document. The referring revision in this section are referring to the document revision. Changes from Rev. 1. Updated "Packaging Information" on page 333, by replacing the package 44A by a correct one. 2503P-07/09 to Rev. 2503Q-02/11 2. Updated the datasheet according to the Atmel new Brand Style Guide. 3. Updated "Ordering Information" on page 332 to include Tape & Reel devices. Changes from Rev. 1. Inserted Note in "Performing Page Erase by SPM" on page 251. 2503O-07/09 to 2. Note 6 and Note 7 in Table 119 on page 290 have been removed. Rev. 2503P-07/10 3. Updated "Performing Page Erase by SPM" on page 251. Changes from Rev. 1. Updated "Errata" on page 336 . 2503N-06/08 to 2. Updated the TOC with new template (version 5.10) Rev. 2503O-07/09 Changes from Rev. 1. Added the note "Not recommended for new designs" on "Features" on page 1. 2503M-05/08 to Rev. 2503N-06/08 Changes from Rev. 1. Updated "Ordering Information" on page 12: 2503L-05/08 to - Commercial ordering codes removed. Rev. - Non Pb-free package option removed. 2503M-05/08 2. Removed note from Feature list in "Analog to Digital Converter" on page 201. 3. Removed note from Table 84 on page 215. Changes from Rev. 1. Updated "Fast PWM Mode" on page 75 in "8-bit Timer/Counter0 with PWM" on page 69: 2503K-08/07 to - Removed the last section describing how to achieve a frequency with 50% duty Rev. cycle waveform output in fast PWM mode. 2503L-05/08 Changes from Rev. 1. Renamed "Input Capture Trigger Source" to "Input Capture Pin Source" on page 94. 2503J-10/06 to 2. Updated "Features" on page 1. Rev. 2503K-08/07 3. Added "Data Retention" on page 6. 4. Updated "Errata" on page 336. 17 2503QS-AVR-02/11 ATmega32(L) 5. Updated "Slave Mode" on page 136. Changes from Rev. 1. Updated "Fast PWM Mode" on page 99. 2503I-04/06 to Rev. 2. Updated Table 38 on page 80, Table 40 on page 81, Table 45 on page 108, Table 47 on 2503J-10/06 page 109, Table 50 on page 125 and Table 52 on page 126. 3. Updated typo in table note 6 in "DC Characteristics" on page 287. 4. Updated "Errata" on page 336. Changes from Rev. 1. Updated Figure 1 on page 2. 2503H-03/05 to 2. Added "Resources" on page 6. Rev. 2503I-04/06 3. Added note to "Timer/Counter Oscillator" on page 31. 4. Updated "Serial Peripheral Interface - SPI" on page 132. 5. Updated note in "Bit Rate Generator Unit" on page 175. 6. Updated Table 86 on page 218. 7. Updated "DC Characteristics" on page 287. Changes from Rev. 1. MLF-package alternative changed to "Quad Flat No-Lead/Micro Lead Frame Package QFN/MLF". 2503G-11/04 to Rev. 2503H-03/05 2. Updated "Electrical Characteristics" on page 287 3. Updated "Ordering Information" on page 332. Changes from Rev. 1. "Channel" renamed "Compare unit" in Timer/Counter sections, ICP renamed ICP1. 2503F-12/03 to 2. Updated Table 7 on page 29, Table 15 on page 37, Table 81 on page 206, Table 114 on Rev. 2503G-11/04 page 272, Table 115 on page 273, and Table 118 on page 289. 3. Updated Figure 1 on page 2, Figure 46 on page 100. 4. Updated "Version" on page 226. 5. Updated "Calibration Byte" on page 258. 6. Added section "Page Size" on page 258. 7. Updated "ATmega32 Typical Characteristics" on page 296. 8. Updated "Ordering Information" on page 332. Changes from Rev. 1. Updated "Calibrated Internal RC Oscillator" on page 29. 2503E-09/03 to Rev. 2503F-12/03 18 2503QS-AVR-02/11 ATmega32(L) Changes from Rev. 1. Updated and changed "On-chip Debug System" to "JTAG Interface and On-chip Debug System" on page 35. 2503D-02/03 to Rev. 2503E-09/03 2. Updated Table 15 on page 37. 3. Updated "Test Access Port - TAP" on page 219 regarding the JTAGEN fuse. 4. Updated description for Bit 7 - JTD: JTAG Interface Disable on page 228. 5. Added a note regarding JTAGEN fuse to Table 104 on page 257. 6. Updated Absolute Maximum Ratings* , DC Characteristics and ADC Characteristics in "Electrical Characteristics" on page 287. 7. Added a proposal for solving problems regarding the JTAG instruction IDCODE in "Errata" on page 336. Changes from Rev. 1. Added EEAR9 in EEARH in "Register Summary" on page 327. 2503C-10/02 to 2. Added Chip Erase as a first step in"Programming the Flash" on page 284 and "ProRev. 2503D-02/03 gramming the EEPROM" on page 285. 3. Removed reference to "Multi-purpose Oscillator" application note and "32 kHz Crystal Oscillator" application note, which do not exist. 4. Added information about PWM symmetry for Timer0 and Timer2. 5. Added note in "Filling the Temporary Buffer (Page Loading)" on page 251 about writing to the EEPROM during an SPM Page Load. 6. Added "Power Consumption" data in "Features" on page 1. 7. Added section "EEPROM Write During Power-down Sleep Mode" on page 22. 8. Added note about Differential Mode with Auto Triggering in "Prescaling and Conversion Timing" on page 204. 9. Updated Table 89 on page 232. 10.Added updated "Packaging Information" on page 333. Changes from Rev. 1. Updated the "DC Characteristics" on page 287. 2503B-10/02 to Rev. 2503C-10/02 Changes from Rev. 1. Canged the endurance on the Flash to 10,000 Write/Erase Cycles. 2503A-03/02 to 2. Bit nr.4 - ADHSM - in SFIOR Register removed. Rev. 2503B-10/02 3. Added the section "Default Clock Source" on page 25. 4. When using External Clock there are some limitations regards to change of frequency. This is described in "External Clock" on page 31 and Table 117 on page 289. 19 2503QS-AVR-02/11 ATmega32(L) 5. Added a sub section regarding OCD-system and power consumption in the section "Minimizing Power Consumption" on page 34. 6. Corrected typo (WGM-bit setting) for: - - - - "Fast PWM Mode" on page 75 (Timer/Counter0) "Phase Correct PWM Mode" on page 76 (Timer/Counter0) "Fast PWM Mode" on page 120 (Timer/Counter2) "Phase Correct PWM Mode" on page 121 (Timer/Counter2) 7. Corrected Table 67 on page 164 (USART). 8. Updated VIL, IIL, and IIH parameter in "DC Characteristics" on page 287. 9. Updated Description of OSCCAL Calibration Byte. In the datasheet, it was not explained how to take advantage of the calibration bytes for 2, 4, and 8 MHz Oscillator selections. This is now added in the following sections: Improved description of "Oscillator Calibration Register - OSCCAL" on page 30 and "Calibration Byte" on page 258. 10. Corrected typo in Table 42. 11. Corrected description in Table 45 and Table 46. 12. Updated Table 118, Table 120, and Table 121. 13. Added "Errata" on page 336. 20 2503QS-AVR-02/11 Atmel Corporation 2325 Orchard Parkway San Jose, CA 95131 USA Tel: (+1)(408) 441-0311 Fax: (+1)(408) 487-2600 www.atmel.com Atmel Asia Limited Unit 1-5 & 16, 19/F BEA Tower, Millennium City 5 418 Kwun Tong Road Kwun Tong, Kowloon HONG KONG Tel: (+852) 2245-6100 Fax: (+852) 2722-1369 Atmel Munich GmbH Business Campus Parkring 4 D-85748 Garching b. Munich GERMANY Tel: (+49) 89-31970-0 Fax: (+49) 89-3194621 Atmel Japan 9F, Tonetsu Shinkawa Bldg. 1-24-8 Shinkawa Chuo-ku, Tokyo 104-0033 JAPAN Tel: (+81)(3) 3523-3551 Fax: (+81)(3) 3523-7581 (c) 2011 Atmel Corporation. All rights reserved. / Rev. CORP0XXXX Atmel (R), Atmel logo and combinations thereof, AVR (R) and others are registered trademarks or trademarks of Atmel Corporation or its subsidiaries. Other terms and product names may be trademarks of others. Disclaimer: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any intellectual property right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN THE ATMEL TERMS AND CONDITIONS OF SALES LOCATED ON THE ATMEL WEBSITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT, CONSEQUENTIAL, PUNITIVE, SPECIAL OR INCIDENTAL DAMAGES (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS AND PROFITS, BUSINESS INTERRUPTION, OR LOSS OF INFORMATION) ARISING OUT OF THE USE OR INABILITY TO USE THIS DOCUMENT, EVEN IF ATMEL HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Atmel makes no representations or warranties with respect to the accuracy or completeness of the contents of this document and reserves the right to make changes to specifications and product descriptions at any time without notice. Atmel does not make any commitment to update the information contained herein. Unless specifically provided otherwise, Atmel products are not suitable for, and shall not be used in, automotive applications. Atmel products are not intended, authorized, or warranted for use as components in applications intended to support or sustain life. 2503QS-AVR-02/11