LTC1346A 10Mbps DCE/DTE V.35 Transceiver U FEATURES DESCRIPTIO Single Chip Provides Complete Differential Signal Interface for V.35 Port Drivers and Receivers Will Withstand Repeated 10kV ESD Pulses Operates from 5V Supplies 10Mbaud Transmission Rate Meets CCITT V.35 Specification Shutdown Mode Reduces ICC to Below 1A Selectable Transmitter and Receiver Configurations Independent Driver/Receiver Enables Transmitter Maintains High Impedance When Disabled, Shut Down or with Power Off Transmitters Are Short-Circuit Protected U APPLICATIO S Modems Telecommunications Data Routers The LTC(R)1346A is a single chip transceiver that provides the differential clock and data signals for a V.35 interface from 5V supplies. Combined with an external resistor termination network and an LT (R)1134A RS232 transceiver for the control signals, the LTC1346A forms a complete low power DTE or DCE V.35 interface port. The LTC1346A features three current output differential transmitters and three differential receivers. The transceiver can be configured for DTE or DCE operation or shutdown using three Select pins. In the Shutdown mode, the supply current is reduced to below 1A. The LTC1346A transceiver operates up to 10Mbaud. All transmitters feature short-circuit protection. Both the transmitter outputs and the receiver outputs can be forced into a high impedance state. The transmitter outputs and receiver inputs feature 10kV ESD protection. , LTC and LT are registered trademarks of Linear Technology Corporation. U TYPICAL APPLICATIO Clock and Data Signals for V.35 Interface 1 VCC1 5V DTE DCE 1 2 2 + 0.1mF 4 5 LTC1346A DX DX BI 627T500/1250 24 1 23 2 22 3 21 4 TXD (103) T T SCTE (113) T T TXC (114) 18 14 9 RX T 17 13 T RXC (115) 16 12 10 RX T 15 11 T RXD (104) 14 10 11 RX 7 VCC1 8 13 3 12 BI 627T500/1250 T 9 8 T 7 GND (102) 8 12 16 11 15 10 14 9 13 1 24 2 23 3 22 4 21 5 20 6 7 + LTC1346A 19 0.1mF VCC2 5V + VEE1 - 5V + 0.1mF VEE2 0.1mF -5V 10 RX 11 RX DX DX DX 4 5 7 3 8 12 50W 6 T VCC2 = 125W 50W BI TECHNOLOGIES 627T500/1250 (SOIC) LTC1346 * TA01 1346afa 1 LTC1346A W U U W W W AXI U U ABSOLUTE PACKAGE/ORDER I FOR ATIO RATI GS (Note 1) Supply Voltage VCC .................................................................... 6.5V VEE ................................................................... - 6.5V Input Voltage Transmitters ........................... - 0.3V to (VCC + 0.3V) Receivers ............................................... - 18V to 18V S0, S1, S2 ............................... - 0.3V to (VCC + 0.3V) Output Voltage Transmitters .......................................... - 18V to 18V Receivers ................................ - 0.3V to (VCC + 0.3V) Short-Circuit Duration Transmitter Output ..................................... Indefinite Receiver Output .......................................... Indefinite Operating Temperature Range LTC1346AC ............................................ 0C to 70C Storage Temperature Range ................ - 65C to 150C Lead Temperature (Soldering, 10 sec)................. 300C ORDER PART NUMBER TOP VIEW VEE 1 24 Y1 VCC 2 23 Z1 GND 3 22 Y2 T1 4 21 Z2 T2 5 20 Y3 T3 6 19 Z3 S1 7 18 A3 S2 8 17 B3 R3 9 16 A2 R2 10 15 B2 R1 11 14 A1 S0 12 13 B1 LTC1346ACSW SW PACKAGE 24-LEAD PLASTIC SO WIDE TJMAX = 150C, JA = 85C/W Consult LTC Marketing for parts specified with wider operating temperature ranges. DC ELECTRICAL CHARACTERISTICS The denotes specifications which apply over the full operating temperature range. VCC = 5V 5%, VEE = - 5V 5% (Note 2) SYMBOL VOD VOC IOH IOL IOZ PARAMETER Transmitter Differential Output Voltage Transmitter Common Mode Output Voltage Transmitter Output High Current Transmitter Output Low Current Transmitter Output Leakage Current CONDITIONS - 4V VOS 4V (Figure 1) VOS = 0V (Figure 1) VY, Z = 0V VY, Z = 0V - 5V VY, Z 5V, S1 = S2 = 0V MIN 0.44 - 0.6 - 12.6 9.4 TYP 0.55 0 - 11 11 1 RO VTH VTH IIN RIN VOH VOL IOSR IOZR VIH VIL IIN Transmitter Output Impedance Differential Receiver Input Threshold Voltage Receiver Input Hysterisis Receiver Input Current (A, B) Receiver Input Impedance Receiver Output High Voltage Receiver Output Low Voltage Receiver Output Short-Circuit Current Receiver Three-State Output Current Logic Input High Voltage Logic Input Low Voltage Logic Input Current - 2V VY, Z 2V - 7V (VA + VB)/2 12V - 7V (VA + VB)/2 12V - 7V VA, B 12V - 7V VA, B 12V IO = 4mA, VA, B = 0.2V IO = 4mA, VA, B = - 0.2V 0V VO VCC S0 = VCC, 0V VO VCC T, S0, S1, S2 T, S0, S1, S2 T, S0, S1, S2 100 25 50 17.5 3 7 200 0.7 MAX 0.66 0.6 - 9.4 12.6 20 100 30 4.5 0.2 40 0.4 85 10 2 0.8 10 UNITS V V mA mA A A k mV mV mA k V V mA A V V A 1346afa 2 LTC1346A AC ELECTRICAL CHARACTERISTICS The denotes specifications which apply over the full operating temperature range. VCC = 5V 5%, VEE = - 5V 5% (Note 2) SYMBOL PARAMETER ICC VCC Supply Current IEE VEE Supply Current tr, tf tPLH tPHL tSKEW tPLH tPHL tSKEW tZL Transmitter Rise or Fall Time Transmitter Input to Output Transmitter Input to Output Transmitter Output to Output Receiver Input to Output Receiver Input to Output Differential Receiver Skew, tPLH - tPHL Receiver Enable to Output Low (Active Mode) Receiver Enable to Output Low (from Shutdown, Note 3) Receiver Enable to Output High (Active Mode) Receiver Enable to Output High (from Shutdown, Note 3) Receiver Disable from Low Receiver Disable from High tZH tLZ tHZ CONDITIONS VOS = 0V, S0 = Low, S1 = S2 = High (Figure 1) No Load, S0 = Low, S1 = S2 = High Shutdown, S0 = VCC, S1 = S2 = 0V VOS = 0V, S0 = Low, S1 = S2 = High (Figure 1) No Load, S0 = Low, S1 = S2 = High Shutdown, S0 = VCC, S1 = S2 = 0V VOS = 0V (Figures 1, 3) VOS = 0V (Figures 1, 3) VOS = 0V (Figures 1, 3) VOS = 0V (Figures 1, 3) VOS = 0V (Figures 1, 4) VOS = 0V (Figures 1, 4) VOS = 0V (Figures 1, 4) CL = 15pF, SW1 Closed (Figures 2, 5) CL = 15pF, SW1 Closed (Figures 2, 5) MIN TYP 40 6 0.1 - 40 -6 - 0.1 7 25 30 5 50 55 5 40 2 MAX 50 9 100 - 50 -9 - 100 40 70 70 100 100 70 UNITS mA mA A mA mA A ns ns ns ns ns ns ns ns s CL = 15pF, SW2 Closed (Figures 2, 5) CL = 15pF, SW2 Closed (Figures 2, 5) 35 2 70 ns s CL = 15pF, SW1 Closed (Figures 2, 5) CL = 15pF, SW2 Closed (Figures 2, 5) 30 35 70 70 ns ns Note 1: The Absolute Maximum Ratings are those values beyond which the life of a device may be impaired. Note 2: All currents into device pins are positive; all currents out of device pins are termed negative. All voltages are referenced to device ground unless otherwise specified. Note 3: Receiver enable to output valid high or low from Shutdown is typically 2s. U W TYPICAL PERFOR A CE CHARACTERISTICS Transmitter Output Current vs Temperature Transmitter Output Current vs Output Voltage 13 13 11 10 9 -50 -25 0 50 75 25 TEMPERATURE (C) 100 125 1346A G01 VCC = 5V VEE = -5V 15 12 TIME (ns) OUTPUT CURRENT (mA) 12 20 TA = 25C VCC = 5V VEE = -5V VCC = 5V VEE = -5V OUTPUT CURRENT (mA) Transmitter Output Skew vs Temperature 11 10 9 -2.0 -1.5 -1.0 -0.5 0 0.5 1.0 OUTPUT VOLTAGE (V) 10 5 1.5 2.0 1346A G02 0 -50 -25 0 50 75 25 TEMPERATURE (C) 100 125 1346A G03 1346afa 3 LTC1346A U W TYPICAL PERFOR A CE CHARACTERISTICS Receiver tPLH - tPHL vs Temperature ICC Supply Current vs Temperature 45 VCC = 5V VEE = -5V LOADED CURRENT (mA) 35 6.5 NO LOAD 0 -50 -25 0 50 75 25 TEMPERATURE (C) 100 125 6.0 25 -50 -25 0 50 75 25 TEMPERATURE (C) -35 -6.0 100 5.5 125 -40 -6.5 -45 -50 -25 0 50 75 25 TEMPERATURE (C) Transmitter Output Waveforms 100 -7.0 125 1346A G06 1346A G05 1346A G04 INPUT 5V/DIV -5.5 NO LOAD LOADED 30 5 -30 7.0 CURRENT (mA) 10 -5.0 VCC = 5V VEE = -5V CURRENT (mA) TIME (ns) VCC = 5V VEE = -5V 40 15 IEE Supply Current vs Temperature -25 7.5 CURRENT (mA) 20 Receiver Enable from Shutdown Receiver Output Waveforms INPUT A-B 1V/DIV INPUT 0.2V/DIV INPUT S0 5V/DIV OUTPUT 0.2V/DIV OUTPUT 5V/DIV OUTPUT 5V/DIV 1346A G07 1346A G08 1346A G09 U U U PIN FUNCTIONS VEE (Pin 1): Negative Supply, - 4.75V VEE - 5.25V B1 (Pin 13): Receiver 1 Inverting Input VCC (Pin 2): Positive Supply, 4.75V VCC 5.25V A1 (Pin 14): Receiver 1 Noninverting Input GND (Pin 3): Ground B2 (Pin 15): Receiver 2 Inverting Input T1 (Pin 4): Transmitter 1 Input, TTL Compatible A2 (Pin 16): Receiver 2 Noninverting Input T2 (Pin 5): Transmitter 2 Input, TTL Compatible B3 (Pin 17): Receiver 3 Inverting Input T3 (Pin 6): Transmitter 3 Input, TTL Compatible A3 (Pin 18): Receiver 3 Noninverting Input S1 (Pin 7): Select Input 1, TTL Compatible Z3 (Pin 19): Transmitter 3 Inverting Output S2 (Pin 8): Select Input 2, TTL Compatible Y3 (Pin 20): Transmitter 3 Noninverting Output R3 (Pin 9): Receiver 3 Output, TTL Compatible Z2 (Pin 21): Transmitter 2 Inverting Output R2 (Pin 10): Receiver 2 Output, TTL Compatible Y2 (Pin 22): Transmitter 2 Noninverting Output R1 (Pin 11): Receiver 1 Output, TTL Compatible Z1 (Pin 23): Transmitter 1 Inverting Output S0 (Pin 12): Select Input 0, TTL Compatible Y1 (Pin 24): Transmitter 1 Noninverting Output 1346afa 4 LTC1346A U U FU CTIO TABLES Transmitter and Receiver Configuration S0 0 1 0 1 0 1 0 1 S1 0 0 1 1 0 0 1 1 S2 0 0 0 0 1 1 1 1 DX ON -- -- 1, 2, 3 1, 2, 3 1, 2 1, 2 1, 2, 3 1, 2, 3 RX ON 1, 2, 3 -- 1, 2 -- 1, 2, 3 -- 1, 2, 3 -- Transmitter Description All RX ON, All DX OFF All OFF, Shutdown DCE Mode DCE Mode, All RX OFF DTE Mode DTE Mode, All RX OFF All ON All DX ON, All RX OFF INPUTS OUTPUTS CONFIGURATION S0 S1 S2 T Y1 AND Y2 Z1 AND Z2 Y3 Z3 All OFF 0 X 0 0 Z Z Z Z Shutdown 1 0 0 X Z Z Z Z DCE or All ON X 1 X 0 0 1 0 1 DCE or All ON X 1 X 1 1 0 1 0 DTE X 0 1 0 0 1 Z Z DTE X 0 1 1 1 0 Z Z Receiver INPUTS CONFIGURATION S0 S1 S2 All Rx ON OUTPUTS A-B R1 AND R2 R3 0 0 0 0 0 -0.2V All Rx ON 0 0 0 0.2V 1 1 Shutdown 1 0 0 X Z Z DCE 0 1 0 -0.2V 0 Z DCE 0 1 0 0.2V 1 Z Disabled 1 1 0 X Z Z DTE or All ON 0 X 1 -0.2V 0 0 DTE or All ON 0 X 1 0.2V 1 1 Disabled 1 X 1 X Z Z TEST CIRCUITS Y 50 T Y 125 VOS 50 A 125 R VOD B Z 50 VOC = (VY + VZ)/2 S0 50 15pF LTC1346A * F01 Z Figure 1. V.35 Transmitter/Receiver Test Circuit VCC SW1 1k RECEIVER OUTPUT CL SW2 LTC1346A * F02 Figure 2. Receiver Output Enable and Disable Timing Test Load 1346afa 5 LTC1346A W U W SWITCHI G TI E WAVEFOR S 3V f = 1MHz: t r 10ns: t f 10ns 1.5V T 1.5V 0V t PLH t PHL VO 90% Y-Z VDIFF = V(Y) - V(Z) 50% 10% -VO 90% 50% 10% 1/2 VO tr tf Z VO Y tSKEW tSKEW LTC1346A * F03 Figure 3. V.35 Transmitter Propagation Delays VOD /2 f = 1MHz: t r 10ns: t f 10ns 0V A-B INPUT 0V -VOD /2 t PLH t PHL VOH R 1.5V OUTPUT 1.5V VOL LTC1346A * F04 Figure 4. V.35 Receiver Propagation Delays 3V 1.5V S0 0V f = 1MHz: t r 10ns: t f 10ns t ZL 1.5V t LZ 5V R 1.5V OUTPUT NORMALLY LOW VOL t ZH OUTPUT NORMALLY HIGH VOH 0.5V t HZ 0.5V 1.5V R 0V LTC1346A * F05 Figure 5. Receiver Enable and Disable Times 1346afa 6 LTC1346A U W U U APPLICATIONS INFORMATION Review of CCITT Recommendation V.35 Electrical Specifications 10. No data errors should occur with 2V common mode change at either the transmitter/receiver or 4V ground potential difference between transmitter and receiver. V.35 is a CCITT recommendation for synchronous data transmission via modems. Appendix 2 of the recommendation describes the electrical specifications which are summarized below: Cable Termination Each end of the cable connected to an LTC1346A must be terminated by an external Y- or -resistor network for proper operation. The Y-termination has two series connected 50 resistors and a 125 resistor connected between ground and the center tap of the two 50 resistors as shown in Figure 6. 1. The interface cable is a balanced twisted pair with 80 to 120 impedance. 2. The transmitter's source impedance is between 50 and 150. 3. The transmitter's resistance between shorted terminals and ground is 150 15. The alternative -termination has a 120 resistor across the twisted wires and two 300 resistors between each wire and ground. Standard 1/8W, 5% surface mount resistors can be used for the termination network. To maintain the proper differential output swing, the resistor tolerance must be 5% or better. A termination network that combines all the resistors into an SO-14 package is available from: 4. When terminated by a 100 resistive load, the terminal-to-terminal voltage should be 0.55V 20%. 5. The transmitter's rise time should be less than 1% of the signal pulse or 40ns, whichever is greater. 6. The common mode voltage at the transmitter output should not exceed 0.6V. BI Technologies (Formerly Beckman Industrial) Resistor Networks 4200 Bonita Place Fullerton, CA 92635 http://www.bitechnologies.com Phone: (714) 447-2357 FAX: (714) 447-2500 Part #: BI Technologies 627T500/1250 (SOIC) 899-5-500/1250 (DIP) 7. The receiver impedance is 100 10. 8. The receiver impedance to ground is 150 15. 9. The transmitter or receiver should not be damaged by connection to earth ground, short-circuiting or cross connection to other lines. 50 125 50 Y 300 120 300 LTC1346A * F06 Figure 6. Y- and -Termination Networks 1346afa 7 LTC1346A U W U U APPLICATIONS INFORMATION CHIP BOUNDARY VCC 11mA Y 50 125 T 50 Z 11mA VEE LTC1346A * F07 Figure 7. Simplified Transmitter Schematic Theory of Operation The transmitter outputs consist of complementary switched-current sources as shown in Figure 7. With a logic zero at the transmitter input, the inverting output Z sources 11mA and the noninverting output Y sinks 11mA. The differential transmitter output voltage is then set by the termination resistors. With two differential 50 resistors at each end of the cable, the voltage is set to (50)(11mA) = 0.55V. With a logic 1 at the transmitter input, output Z sinks 11mA and Y sources 11mA. The common mode voltage of Y and Z is 0V when both current sources are matched and there is no ground potential difference between the cable terminations. The transmitter current sources have a common mode range of 2V, which allows for a ground difference between cable terminations of 4V. Each receiver input has a 30k resistance to ground and requires external termination to meet the V.35 input impedance specification. The receivers have an input hysteresis of 50mV to improve noise immunity. Three Select pins, S0, S1 and S2, configure the chip as described in Function Tables. When the transmitters and receivers are OFF, all outputs are forced into high impedance. The S0 pin can be used as receiver output enable. In Shutdown mode, ICC drops to 1A with all transmitters and receivers OFF. When the LTC1346A is enabled from Shutdown the transmitters and receivers require 2s to stabilize. Complete V.35 Port Figure 8 shows the schematic of a complete surface mounted, 5V DTE and DCE V.35 port using only three ICs and six capacitors per port. The LTC1346A is used to transmit the clock and data signals and the LT1134A to transmit the control signals. If test signals 140, 141 and 142 are not used, the transmitter inputs should be tied to VCC. RS422/RS485 Applications The receivers on the LTC1346A can be used for RS422 and RS485 applications. Using the test circuit in Figure 9, the LTC1346A receivers are able to successfully extract the data stream from the common mode voltage, meeting RS422 and RS485 requirements as shown in Figures 10 and 11. 1346afa 8 LTC1346A U U W U APPLICATIONS INFORMATION DTE 50 T VEE1 -5V VCC1 5V 2 0.1F LTC1346A 24 4 DX 5 DX 9 RX 10 RX 11 RX 12 1 23 2 22 3 21 4 18 14 17 13 16 12 15 11 14 10 13 9 3 7 VCC1 0.2F 4 T P TXD (103) S U T S SCTE (113) W AA T TXC (114) T V T T R T X V RXD (104) T AA Y RXC (115) T U W Y X P BI 627T500/ 1250 (SOIC) T T R B GND (102) B A CABLE SHIELD A T VCC2 5V 1 3 22 2 0.1F 12 16 11 15 10 14 9 13 1 24 2 23 3 22 4 21 5 20 6 19 7 3 11 RX 4 DX 5 DX 6 DX 7 8 12 VCC2 23 4 LT1134A 10 RX 0.2F 24 0.2F 3 22 1 0.1F 0.1F LTC1346A 8 0.2F 1 0.1F BI 627T500/ 1250 (SOIC) 8 7 8 VEE2 -5V 50 1 0.1F DCE 125 = 0.1F 23 24 LT1134A 0.1F 2 21 19 20 18 OPTIONAL SIGNALS 16 14 17 15 DX DX RX RX RX RX DX DX 13 5 H DTR (108) 7 C RTS (105) 6 E DSR (107) 8 D CTS (106) 10 F DCD (109) 12 NN TM (142) 9 N RDL (140) 11 L LLB (141) H 6 C 8 E 5 D 7 F 9 NN 11 N 10 L 12 ISO 2593 ISO 2593 34-PIN DTE/DCE 34-PIN DTE/DCE INTERFACE CONNECTOR INTERFACE CONNECTOR 20 RX 18 RX DX DX DX DX 21 19 17 15 16 RX 14 RX 13 LTC1346A * TA08 Figure 8. Complete Single 5V V.35 Interface 1346afa 9 LTC1346A U W U U APPLICATIONS INFORMATION VCC1 5V VCC2 5V A A 1009 LTC485 GND 1009 B B GND +- TTL IN TTL OUT LTC1346A VEE -5V 7V TO - 7V GND POTENTIAL DIFFERENCE LTC1346A * F09 Figure 9. RS422/RS485 Receiver Interface 5V RECEIVER OUTPUT 5V/DIV RECEIVER A INPUT B 5V/DIV 15V 0V 10V 5V 0V 0V -5V RECEIVER INPUT B A 5V/DIV -10V 5V RECEIVER OUTPUT 5V/DIV 0V LTC1346 * F10 Figure 10. - 7V Common Mode Multiprotocol Application The LTC1346A can be used in multiprotocol applications where V.35, RS232 and RS422 (used in RS530, RS449 among others) signals may appear at the same port. The LTC1346A switched current source driver is not compatible with RS232 or RS422. However, the outputs when disabled can share lines with RS232 drivers with a Shutdown feature such as the LT1030 and RS422 drivers with a disable feature such as the LTC486/LTC487 (Figure 12a). LTC1346 * F11 Figure 11. 12V Common Mode The LTC1346A driver will not be damaged or load the shared lines when disabled. The LTC1346A receiver can receive V.35, RS232 and RS422 signals as shown in Figure 12b. The LTC1346A receiver is directly compatible with V.35 and RS422. For RS232 signal, the noninverting input of the receiver should be grounded. Because the line termination for each of the protocols is different, some form of termination switching should be included, either the connector (as shown in Figures 12a and 12b) or on the PCB. 1346afa 10 LTC1346A U U W U APPLICATIONS INFORMATION LT1030 V.35 DIFFERENTIAL CONNECTION WITH TERMINATION LTC487 RS422 DIFFERENTIAL CONNECTION RS232 CONNECTION NO CONNECTION LTC1346A CONNECTOR 50 125 50 LOGIC INPUT 1346A F12a Figure 12a. Multiprotocol Transmitter V.35 DIFFERENTIAL CONNECTION WITH TERMINATION RS232 CONNECTION WITH TERMINATION 50 CONNECTOR LTC1346A LOGIC OUTPUT RS422 DIFFERENTIAL CONNECTION WITH TERMINATION 125 100 5k 50 1346A F12b Figure 12b. Multiprotocol Receiver 1346afa Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights. 11 LTC1346A U PACKAGE DESCRIPTIO Dimensions in inches (millimeters) unless otherwise noted. SW Package 24-Lead Plastic Small Outline (Wide 0.300) (LTC DWG # 05-08-1620) .050 BSC .045 .005 .030 .005 TYP N 24 23 22 21 .598 - .614 (15.190 - 15.600) NOTE 4 20 19 18 17 16 15 14 13 N .325 .005 .420 MIN .394 - .419 (10.007 - 10.643) NOTE 3 1 2 3 N/2 N/2 RECOMMENDED SOLDER PAD LAYOUT .005 (0.127) RAD MIN .009 - .013 (0.229 - 0.330) .291 - .299 (7.391 - 7.595) NOTE 4 .010 - .029 x 45 (0.254 - 0.737) 1 2 3 4 5 6 7 8 9 10 11 12 .037 - .045 (0.940 - 1.143) .093 - .104 (2.362 - 2.642) 0 - 8 TYP .050 (1.270) BSC NOTE 3 .004 - .012 (0.102 - 0.305) .014 - .019 (0.356 - 0.482) TYP .016 - .050 (0.406 - 1.270) NOTE: 1. DIMENSIONS IN INCHES (MILLIMETERS) 2. DRAWING NOT TO SCALE 3. PIN 1 IDENT, NOTCH ON TOP AND CAVITIES ON THE BOTTOM OF PACKAGES ARE THE MANUFACTURING OPTIONS. THE PART MAY BE SUPPLIED WITH OR WITHOUT ANY OF THE OPTIONS 4. THESE DIMENSIONS DO NOT INCLUDE MOLD FLASH OR PROTRUSIONS. MOLD FLASH OR PROTRUSIONS SHALL NOT EXCEED .006" (0.15mm) S24 (WIDE) 0502 RELATED PARTS PART NUMBER DESCRIPTION COMMENTS LT1134A 5V Only, 4-Driver/4-Receiver RS232 Transceiver Forms Complete V.35 Interface with LTC1346A LTC1334 5V Only, Configurable RS232/RS485 Transceiver Includes On-Chip Charge Pump LTC1344/LTC1344A Multiprotocol Cable Terminator Software Selectable, Supports V.35, V.36, V.28, EIA-530, EIA-530-A, RS449, X.21 LTC1544 4-Driver, 4-Receiver Multiprotocol Transceiver 5V Supply, Supports V.35, V.36, V.28, EIA-530, EIA-530-A, RS449, X.21 LTC1545 5-Driver, 5-Receiver Multiprotocol Transceiver 5V Supply, Supports V.35, V.36, V.28, EIA-530, EIA-530-A, RS449, X.21 LTC1546 3-Driver, 3-Receiver Multiprotocol Transceiver with Termination 5V Supply, Supports V.35, V.36, V.28, EIA-530, EIA-530-A, RS449, X.21 LTC2844 3.3V, 4-Driver, 4-Receiver Multiprotocol Transceiver 3.3V Supply, Supports V.35, V.36, V.28, EIA-530, EIA-530-A, RS449, X.21 LTC2845 3.3V, 5-Driver, 5-Receiver Multiprotocol Transceiver 3.3V Supply, Supports V.35, V.36, V.28, EIA-530, EIA-530-A, RS449, X.21 LTC2846 3.3V, 3-Driver, 3-Receiver Multiprotocol Transceiver with Termination 3.3V Supply, Supports V.35, V.36, V.28, EIA-530, EIA-530-A, RS449, X.21 1346afa 12 Linear Technology Corporation LW/TP 1002 1K REV A * PRINTED IN USA 1630 McCarthy Blvd., Milpitas, CA 95035-7417 (408) 432-1900 FAX: (408) 434-0507 www.linear.com LINEAR TECHNOLOGY CORPORATION 1995