ELECTRICAL SPECIFICATIONS: 1.0 INDUCTANCE: Pi-J1l=Pe-Je ; P4-J4=P5-J5 2.0 DC RESISTANCE: i) P4 Pe O@ @|@|@ @ : 65 uH O0.01V, 10 KHz, nominal. Pi-J1 ' 5 ohm MAX Pe-Je ' 5 ohm MAX P4-J4 ' 5 ohm MAX PS-JS ' 5 ohm MAX 3.0 Common Modcle: CMA (-dB> FREQUENCY <MHz> TYPICAL _MIN_ 1 8 5 5 17 15 20 23 15 70 25 20 200 22 17 500 ii 6 NOTES: PINS NOT ELECTRICALLY CONNECTED ARE OMITTED. InNet Technologies Inc. http://www.innettech.com Stewart Connector Systems http'//www.stewartconnector.com an OF 3 DRAWING "SI-4001 i 06 L*.635 [16.13] MAX NIOIYO 40 AYLNNOD 4d09 Alva YJEWNN Lad LANUI |+ 850 [21.59] MAX. T T +708 [17.98]} + = LED YELLOW LED J GRN/RED LL. 450 [11. wf BICOLOR LED POLARITY (ENLARGED VIEW) RED GREEN CT720034x1 /24-0046 148 [3.75] HIGHEST POINT OF BEAM , a = rs tL 8 5 x 6 S 3 Pay yy uw om S - eg oF SS} 2 | S e = en nl i ES | | 083 [2.12] +] | | HIGHEST POINT 040 [1.02 OF BEAM 495 [10.79] (107 050 [1.27] TYP TOL NON-ACCUM 025 [0.64] > al 100 [2.54] WP SS SIGNAL (SIGNAL) TOL NON-ACCUM & ss, 9.035 [0.89] (8) = 5 PIN 1 aq Ye if 9.062 [1.57] (2) _ + r (SHIELD) ? | - (Posts) nw? re 160 9128 iE a (2 po ge 7125 [3.18 La 0.040[ 1.024) At Ee [11. a) (LED'S) * foi ma +=-*.610 [15.49] -] 120 [3.05] P.C.B. RECOMMENDED HOLE LAYOUT SEEN FROM COMPONENT SIDE TOLERANCE +.003 [0.08] UNLESS OTHERWISE SPECIFIED NOTES: TOLERANCES COMPLY WITH F.C.C. DIMENSION REQUIREMENTS DIMENSIONS SHOWN WITH * TO BE CENTRAL ABOUT CENTER LINE DIMENSIONS SHOWN ARE SUBJECT TO CHANGE WITHOUT NOTICE. PIN NOT ELECTRICALLY CONNECTED MAYBE OMITTED. SEE ELECTRICAL DRAWING FOR OMITTED PINS. AVAILABLE WITH: STANDARD 50 MICRO-INCH SELECTIVE GOLD PLATING (AVAILABLE WITH 30) BICOLOR LED SPECIFICATIONS - COLOR: BICOLOR RED FORWARD VOLTAGE(20mA) : 2.5V (MAX) RED FORWARD VOLTAGE(20mA) : 2.1V (TYP) RED POWER DISSIPATION : 105mW RED WAVE LENGTH: 625nm RED LUMINOUS INTENSITY (20mA) : 5-32 MCD GREEN FORWARD VOLTAGE(20mA) : 2.6V (MAX) GREEN FORWARD VOLTAGE(20mA) : 2.25V (TYP) GREEN POWER DISSIPATION : 105mW GREEN WAVE LENGTH: 555nm GREEN LUMINOUS INTENSITY (20mA) : 5-20 MCD LED SPECIFICATIONS - COLOR: YELLOW FORWARD VOLTAGE(20mA) : 2.5v (MAX) FORWARD VOLTAGE(20mA) : 2.1V (TYP) POWER DISSIPATION : 105mW WAVE LENGTH: 590nm LUMINOUS INTENSITY (10mA) : 2-8 MCD InNet Technologies Inc. http://wwwinnet-tech.com Stewart Connector Systems http://www.stewartconnector.com of 3 DRAWING NO. S I _ 4 0 0 1 1 ~O 1 1300 1200 1100 1000 900 800 700 600 500 400 300 200 100 No mwN +.005 S.0.S. -.005 So ) SX So 8 | | +.010 -.020 PANEL GROUNDING BEAM DEFLECTION S.0.S. = SUGGESTED OPENING SIZE SUGGESTED PANEL OPENING CT720034X1 /24-001302 L .000 (TOP OF PCB TO BOTTOM OF OPENING) :010 MAX. RADIUS(4) POINT OF CONTACT WITH PANEL _~ .080 > 6 ta Spor THE SUGGESTED PANEL OPENING IS INTENDED TO GIVE THE USER THE ABILITY TO HAVE REASONABLE JACK / PANEL CLEARANCES YET MAINTAIN RELIABLE GROUNDING CAPABILITY. THESE VARIABLES CAN BE ADJUSTED IN EITHER DIRECTION BUT MAY CARRY SOME CONSEQUENCES IN THE FORM OF LOWER MATING FORCES OR TIGHTER ASSEMBLY TOLERANCES. FORCE VALUES ON THE GRAPH ARE GENERAL AVERAGES TAKEN AT THE POINT OF CONTACT SHOWN ABOVE. THE SUGGESTED PANEL OPENING INCLUDES APPROXIMATELY .020 CLEARANCE ON THE SIDES AND TOP AND .013 ON THE BOTTOM, AT PANEL OPENING. InNet Technologies Inc. http://www.innettech.com Stewart Connector Systems http://www.stewartconnector.com SHEET 3 of 3 _~" ST-4A0011 ~ Ol