Click on Series name for product info on aimtec.com Series AMSRW-78Z Up to 7.5 Watt | DC-DC Switching Regulator FEATURES: 3 Pin SIP package Very high efficiency up to 95% Non Isolated Low Ripple and Noise * * * * Models Single output Model Input Voltage (V) AMSRW-783.3Z AMSRW-7805Z AMSRW-786.5Z AMSRW-787.2Z AMSRW-7809Z AMSRW-7812Z AMSRW-7815Z 9-72 9-72 9-72 14-72 14-72 17-72 20-72 Input Specifications Parameters Voltage range Filter No Load Input Current Input reflected ripple current Output Voltage (V) Parameters General Specifications Parameters Switching frequency Operating temperature Storage temperature Maximum case temperature Cooling Humidity Case material Weight Dimensions (L x W x H) MTBF Maximum soldering temperature 500 500 500 500 500 500 500 Nominal 100% Load Typical Conditions 82 87 91 91 92 94 95 -40 to +125 120 to 800 -40 to +85 75 80 83 84 86 89 91 Units 0.3 35 mA mA p-p VDC Maximum 3 Continuous Auto recovery 1 0.6 0.02 75 Typical Efficiency Vin Max (%) Maximum Typical 20MHz Bandwidth 100% load Derating above 60C Efficiency Vin Min (%) 100 100 100 100 100 100 100 Vin=(LL-HL) at full load From 10% to 100% Load Conditions Max Capacitive Load (uF) See table above Capacitor Vin=(LL-HL) at 0% load Full Load Output Specifications Voltage accuracy Short Circuit protection Short circuit restart Line voltage regulation Load voltage regulation Temperature coefficient Ripple & Noise Output Current max (mA) 3.3 5 6.5 7.2 9 12 15 High voltage input range up to 72V Operating temperature -40C to +85C Pin Compatible with multiple manufacturers Continuous Short Circuit Protection * * * * % % of Vin % %/oC mV p-p Maximum Free air convection Units Units KHz o C o C o C 105 95 Non Conductive Black Plastic(UL94V-0 rated) 1.8 0.46 x 0.29 x 0.40 inches 11.68 x 7.50 x 10.20 mm >4.5 Mhours (MIL-HDBK-217F, Ground Benign, t=+25C) 260 % RH g o C NOTE: All specifications in this datasheet are measured at an ambient temperature of 25C, humidity<75%, nominal input voltage and at rated output load unless otherwise specified. www.aimtec.com F 051e R12.E Tel: +1 514 620 2722 1 of 4 Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AMSRW-78Z Up to 7.5 Watt | DC-DC Switching Regulator Safety Specifications Parameters Agency Approvals Standards CE EN 55022 class B EN 55024 IEC 61000-4-2 IEC 61000-4-3 IEC 61000-4-4 IEC 61000-4-5 IEC 61000-4-6 IEC 61000-4-8 Pin Out Specifications Pin 1 2 3 Single +V input GND +V output Dimensions 7.50 (0.29) 11.68 (0.46) 10.20 (0.40) 4.00 (0.16) 2.54 (0.10) Dimensions are in mm (inch) Pin Pitch Tolerance: 0.35 (0.014) 2.00 (0.08) 0.50 (0.02) www.aimtec.com F 051e R12.E Case Tolerance: 0.50 (0.02) 0.50 (0.02) 0.30 (0.01) 7.50 (0.29) 0.50 (0.02) 9.70 (0.38) PRINTED FACE Tel: +1 514 620 2722 2 of 4 Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AMSRW-78Z Up to 7.5 Watt | DC-DC Switching Regulator Derating Free Air Convection 60 C Output Power (%) 100 80 Safe Operating Area 60 40 20 0 - 40 - 20 0 20 40 60 80 85 100 Ambient Temperature C EMI/EMS Solution C1 220uF, 100V www.aimtec.com F 051e R12.E +V output +V input L 12uH C2 220uF, 100V AMSRW-78Z GND Tel: +1 514 620 2722 3 of 4 Load Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AMSRW-78Z Up to 7.5 Watt | DC-DC Switching Regulator NOTE: 1. Datasheets are updated as needed and as such, specifications are subject to change without notice. Once printed or downloaded, datasheets are no longer controlled by Aimtec; refer to www.aimtec.com for the most current product specifications. 2. Product labels shown, including safety agency certifications on labels, may vary based on the date manufactured. 3. Mechanical drawings and specifications are for reference only. 4. All specifications are measured at an ambient temperature of 25C, humidity<75%, nominal input voltage and at rated output load unless otherwise specified. 5. Aimtec may not have conducted destructive testing or chemical analysis on all internal components and chemicals at the time of publishing this document. CAS numbers and other limited information are considered proprietary and may not be available for release. 6. This product is not designed for use in critical life support systems, equipment used in hazardous environments, nuclear control systems or other such applications which necessitate specific safety and regulatory standards other the ones listed in this datasheet. 7. Warranty is in accordance with Aimtec's standard Terms of Sale available at www.aimtec.com. www.aimtec.com F 051e R12.E Tel: +1 514 620 2722 4 of 4 Toll free: + 1 888 9 AIMTEC (924 6832) North America only