SPXO SG-3030JF
Product name SG-3030JF 32.768000 kHz B
Product Number / Ordering code Q3102JF020001xx
Please refer to the 8.Packing information about xx (last 2 digits)
Output waveform CMOS
Complies with EU RoHS directive
Reference weight Typ. 90 mg
1.Absolute maximum ratings
Parameter Symbol Min. Typ. Max. Unit Conditions / Remarks
Maximum supply voltage
Vcc-GND -0.3 - 7 V Vcc Pin
Storage temperature T_stg -55 - 125 ºC Storage as single product
2.Specifications(characteristics)
Parameter Symbol Min. Typ. Max. Unit Conditions / Remarks
Output frequency f0 - 32.7680 - kHz
Supply voltage Vcc 1.5 - 5.5 V Vcc Pin
Interface power supply voltage
VIO 1.5 - 5.5 VIO Pin
Operating temperature T_use -40 - 85 ºC No condensation
Frequency tolerance f_tol -18 - 28
x10-6 @+25℃, Vcc=3.3V , 5+/-23x10^-6
Frequency temperature coefficient f0-Tc -120 - 10
x10-6 -20℃ to 70℃ (+25℃ is reference)
Frequency voltage coefficient f0-Vcc -2 - 2
x10-6 /V `@+25℃ Vcc=1.5V to 5.5V
Current consumption Icc - - 2 μA Vcc=3.3V No load condition
Symmetry SYM 45 50 55 %1/2Vcc(VIO）Level
Output voltage
VOH VIO-0.4 - - IOH=-400μA
VOL - - GND+0.4 IOL=400μA
Output load condition L_CMOS - - 15 pF CMOS Load
Input voltage
VIH 80%Vcc - - -
VIL - - 20%Vcc -
Rise time
tr- - 200 ns 20%VIO ⇔ 80%VIO 15pF VIO=1.5V to 5.5V
Fall time tf - - 200 ns 20%VIO ⇔ 80%VIO 15pF　VIO=1.8V to 5.5V
Start-up time t_str - - 1 s Vcc=2.0V to 5.5V
Frequency aging f_age -5 - 5
x10-6 @+25℃ Vcc=3.3V First year
3.Timing chart
GND
VCC
tr
50 %VCC
t
80 %VCC
20 %VCC
tf
1 Page
4.Test circuit
1) Waveform observation
2) Current consumption
*Current consumption under the
disable function should be
= GND.
3) Condition
(1) Oscilloscope
· Band width should be minimum 5 times higher (wider) than measurement frequency.
· Probe earth should be placed closely from test point and lead length should be as short as
possible.
* Recommendable to use miniature socket. (Don’t use earth lead.)
(2) L_CMOS also includes probe capacitance.
(3) By-pass capacitor (0.01 mF to 0.1 mF) is placed closely between VCC and GND.
(4) Use the current meter whose internal impedance value is small.
(5) Power supply
· Start up time (0 %VCC ® 90 %VCC) of power source should be more than 150 ms.
· Impedance of power supply should be as lowest as possible.
VCC
ST
OUT
GND
swich
supply
by-pass
capacitor
Test
Point
A
or
OE
or
OE
VCC
ST
OUT
GND
swich
supply
by-pass
capacitor
L_CMOS
Test Point
2 Page
5.External dimensions (Unit: mm) 6.Footprint(Recommended) (Unit: mm)
7.Reflow profile
Pre Heating Temperature
Tp1 ~ Tp2 = + 170 °C
Heating Temperature
TMlt = + 220 °C
Peek Temperature
TMax. = + 260 °C
Point of measuring
In case of Solder ability
Terminal.
In case of Resistance to soldering heat
Surface.
8.Packing information
[ 1 ]Product number last 2 digits code(xx) description The recommended code is "00"
Q3102JF020001xx
Code Code
01 Any Q'ty vinyl bag(Tape cut) 13 500pcs / Reel
11 Any Q'ty / Reel 00 1000pcs / Reel
12 250pcs / Reel
Condition
Condition
t(time)
Tmlt
Tp2
Tp1
100s
+220ºC
+260ºC
TMax.
Temperature
35s
5.08
0.4
0 Min.
1.5 Max.
7.1±0.2
5.1±0.2
4.6±0.2
SG3030 B
E 9245A
#1 #2
#3
#4
(0.75)
(0.75)
1.8
5.08
4.2
2.0
3 Page
[ 2 ] Taping specification
Subject to EIA-481 & IEC-60286
(1) Tape dimensions
　　　Material of the Carrier Tape : PS
　　　Material of the Top Tape : PET+PE Unit: mm
Symbol A B C D E F
Value φ1.5 4 8 9.25 16 2.3
(2) Reel dimensions
Center material : PS
Material of the Reel : PS
A
B
D
E
C
F
Top tape
Carrier tape
4 Page
9.Notice
10.Contact us
http://www5.epsondevice.com/en/contact/
· This material is subject to change without notice.
· Any part of this material may not be reproduced or duplicated in any form or any means without the written
permission of Seiko Epson.
· The information about applied data,circuitry, software, usage, etc. written in this material is intended for
reference only.
Seiko Epson does not assume any liability for the occurrence of customer damage or infringing on any patent
or copyright of a third party.
This material does not authorize the licensing for any patent or intellectual copyrights.
· When exporting the products or technology described in this material, you should comply with the applicable
export control laws and regulations and follow the procedures required by such laws and regulations.
· You are requested not to use the products (and any technical information furnished, if any) for the development
and/or manufacture of weapon of mass destruction or for other military purposes. You are also requested that
you
would not make the products available to any third party who may use the products for such prohibited
purposes.
· These products are intended for general use in electronic equipment. When using them in specific applications
that require
extremely high reliability, such as the applications stated below, you must obtain permission from Seiko Epson
in advance.
/ Space equipment (artificial satellites, rockets, etc.)
/ Transportation vehicles and related (automobiles, aircraft, trains, vessels, etc.)
/ Medical instruments to sustain life
/ Submarine transmitters
/ Power stations and related
/ Fire work equipment and security equipment
/ Traffic control equipment
/ And others requiring equivalent reliability.
5 Page