Two Selectable Inputs, 12 LVPECL Outputs, SiGe Clock Fanout Buffer ADCLK954 FEATURES FUNCTIONAL BLOCK DIAGRAM 2 selectable differential inputs 4.8 GHz operating frequency 75 fs rms broadband random jitter On-chip input terminations 3.3 V power supply LVPECL ADCLK954 Q0 Q0 Q1 Q1 APPLICATIONS Q2 Low jitter clock distribution Clock and data signal restoration Level translation Wireless communications Wired communications Medical and industrial imaging ATE and high performance instrumentation Q2 The ADCLK954 is an ultrafast clock fanout buffer fabricated on the Analog Devices, Inc., proprietary XFCB3 silicon germanium (SiGe) bipolar process. This device is designed for high speed applications requiring low jitter. The device has two selectable differential inputs via the IN_SEL control pin. Both inputs are equipped with center tapped, differential, 100 on-chip termination resistors. The inputs accept dc-coupled LVPECL, CML, 3.3 V CMOS (single-ended), and ac-coupled 1.8 V CMOS, LVDS, and LVPECL inputs. A VREFx pin is available for biasing ac-coupled inputs. Q3 REFERENCE Q3 Q4 V T0 Q4 CLK0 CLK0 Q5 V T1 Q5 CLK1 Q6 CLK1 Q6 Q7 IN_SEL VREF 1 Q7 REFERENCE Q8 Q9 Q9 Q10 The ADCLK954 features 12 full-swing emitter coupled logic (ECL) output drivers. For LVPECL (positive ECL) operation, bias VCC to the positive supply and VEE to ground. For ECL operation, bias VCC to ground and VEE to the negative supply. The output stages are designed to directly drive 800 mV each side into 50 terminated to VCC - 2 V for a total differential output swing of 1.6 V. Q8 Q10 Q11 Q11 07968-001 GENERAL DESCRIPTION VREF 0 Figure 1. The ADCLK954 is available in a 40-lead LFCSP and specified for operation over the standard industrial temperature range of -40C to +85C. Rev. B Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. Specifications subject to change without notice. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Trademarks and registered trademarks are the property of their respective owners. One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Tel: 781.329.4700 www.analog.com Fax: 781.461.3113 (c)2009-2010 Analog Devices, Inc. All rights reserved. ADCLK954 TABLE OF CONTENTS Features .............................................................................................. 1 Pin Configuration and Function Descriptions..............................6 Applications ....................................................................................... 1 Typical Performance Characteristics ..............................................7 General Description ......................................................................... 1 Functional Description .....................................................................9 Functional Block Diagram .............................................................. 1 Clock Inputs ...................................................................................9 Revision History ............................................................................... 2 Clock Outputs ................................................................................9 Specifications..................................................................................... 3 Clock Input Select (IN_SEL) Settings...................................... 10 Electrical Characteristics ............................................................. 3 PCB Layout Considerations ...................................................... 10 Absolute Maximum Ratings............................................................ 5 Input Termination Options ....................................................... 11 Determining Junction Temperature .......................................... 5 Outline Dimensions ....................................................................... 12 ESD Caution .................................................................................. 5 Ordering Guide .......................................................................... 12 Thermal Performance .................................................................. 5 REVISION HISTORY 6/10--Rev. A to Rev. B Changed Output Voltage Differential Parameter to Output Voltage, Single Ended Parameter, Table 1 ..................................... 3 Changes to Output Voltage, Single Ended Parameter, Table 1 ... 3 7/09--Rev. 0 to Rev. A Changes to Table 1 ............................................................................ 3 Changes to Negative Supply Current, Table 4............................... 4 Changes to Positive Supply Current, Table 4 ................................ 4 Changes to Figure 10 ........................................................................ 8 1/09--Revision 0: Initial Version Rev. B | Page 2 of 12 ADCLK954 SPECIFICATIONS ELECTRICAL CHARACTERISTICS Typical (Typ column) values are given for VCC - VEE = 3.3 V and TA = 25C, unless otherwise noted. Minimum (Min column) and maximum (Max column) values are given over the full VCC - VEE = 3.3 V 10% and TA = -40C to +85C variation, unless otherwise noted. Table 1. Clock Inputs and Outputs Parameter DC INPUT CHARACTERISTICS Input Common-Mode Voltage Input Differential Range Input Capacitance Input Resistance Single-Ended Mode Differential Mode Common Mode Input Bias Current Hysteresis DC OUTPUT CHARACTERISTICS Output Voltage High Level Output Voltage Low Level Output Voltage, Single Ended Reference Voltage Output Voltage Output Resistance Symbol Min VICM VID CIN VEE + 1.5 0.4 VOH VOL VO VREF Typ Max Unit Test Conditions/Comments VCC - 0.1 3.4 1.7 V between input pins 0.4 V V p-p pF 50 100 50 20 10 k A mV Open VTx V V mV 50 to (VCC - 2.0 V) 50 to (VCC - 2.0 V) VOH - VOL, output static V -500 A to +500 A Unit Test Conditions/Comments GHz See Figure 4 for differential output voltage vs. frequency, > 0.8 V differential output swing 20% to 80% measured differentially VCC - 1.26 VCC - 1.99 610 VCC - 0.76 VCC - 1.54 960 (VCC + 1)/2 235 Table 2. Timing Characteristics Parameter AC PERFORMANCE Maximum Output Frequency Symbol Output Rise Time Output Fall Time Propagation Delay Temperature Coefficient Output-to-Output Skew 1 Part-to-Part Skew Additive Time Jitter Integrated Random Jitter Broadband Random Jitter 2 Crosstalk-Induced Jitter 3 CLOCK OUTPUT PHASE NOISE Absolute Phase Noise tR tF tPD fIN = 1 GHz 1 2 3 Min Typ 4.5 4.8 40 40 175 75 75 210 50 9 Max 90 90 245 25 45 28 75 90 -119 -134 -145 -150 -150 ps ps ps fs/C ps ps fs rms fs rms fs rms dBc/Hz dBc/Hz dBc/Hz dBc/Hz dBc/Hz VICM = 2 V, VID = 1.6 V p-p VID = 1.6 V p-p BW = 12 kHz - 20 MHz, CLK = 1 GHz VID = 1.6 V p-p, 8 V/ns, VICM = 2 V Input slew rate > 1 V/ns (see Figure 11, the phase noise plot, for more details) @100 Hz offset @1 kHz offset @10 kHz offset @100 kHz offset >1 MHz offset The output skew is the difference between any two similar delay paths while operating at the same voltage and temperature. Measured at the rising edge of the clock signal; calculated using the SNR of the ADC method. This is the amount of added jitter measured at the output while two related, asynchronous, differential frequencies are applied to the inputs. Rev. B | Page 3 of 12 ADCLK954 Table 3. Input Select Control Pin Parameter Logic 1 Voltage Logic 0 Voltage Logic 1 Current Logic 0 Current Capacitance Symbol VIH VIL IIH IIL Min VCC - 0.4 VEE Typ 2 Max VCC 1.0 100 0.6 Unit V V A mA pF Table 4. Power Parameter POWER SUPPLY Supply Voltage Requirement Power Supply Current Negative Supply Current Positive Supply Current Power Supply Rejection 1 Output Swing Supply Rejection 2 1 2 Symbol Min VCC - VEE 2.97 IVEE IVCC PSRVCC PSRVCC Typ 118 406 <3 28 Change in tPD per change in VCC. Change in output swing per change in VCC. Rev. B | Page 4 of 12 Max Unit Test Conditions/Comments 3.63 V 160 460 mA mA ps/V dB 3.3 V + 10% Static VCC - VEE = 3.3 V 10% VCC - VEE = 3.3 V 10% VCC - VEE = 3.3 V 10% VCC - VEE = 3.3 V 10% ADCLK954 ABSOLUTE MAXIMUM RATINGS DETERMINING JUNCTION TEMPERATURE Table 5. Parameter Supply Voltage VCC - VEE Input Voltage CLK0, CLK1, CLK0, CLK1, IN_SEL CLK0, CLK1, CLK0, CLK1 to VTx Pin (CML, LVPECL Termination) CLK0, CLK1 to CLK0, CLK1 Input Termination, VTx to CLK0, CLK1, CLK0, and CLK1 Maximum Voltage on Output Pins Maximum Output Current Voltage Reference (VREFx) Operating Temperature Range Ambient Junction Storage Temperature Range To determine the junction temperature on the application printed circuit board (PCB), use the following equation: Rating 6.0 V TJ = TCASE + (JT x PD) where: TJ is the junction temperature (C). TCASE is the case temperature (C) measured by the customer at the top center of the package. JT is from Table 6. PD is the power dissipation. VEE - 0.5 V to VCC + 0.5 V 40 mA 1.8 V 2 V Values of JA are provided for package comparison and PCB design considerations. JA can be used for a first-order approximation of TJ by the equation VCC + 0.5 V 35 mA VCC to VEE TJ = TA + (JA x PD) where TA is the ambient temperature (C). -40C to +85C 150C -65C to +150C Values of JB are provided in Table 6 for package comparison and PCB design considerations. Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only; functional operation of the device at these or any other conditions above those indicated in the operational section of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. ESD CAUTION THERMAL PERFORMANCE Table 6. Parameter Junction-to-Ambient Thermal Resistance Still Air 0.0 m/sec Air Flow Moving Air 1.0 m/sec Air Flow 2.5 m/sec Air Flow Junction-to-Board Thermal Resistance Moving Air 1.0 m/sec Air Flow Junction-to-Case Thermal Resistance Moving Air Die-to-Heat Sink Junction-to-Top-of-Package Characterization Parameter Still Air 0 m/sec Air Flow 1 Symbol Description Value 1 Unit 46.1 C/W 40.3 36.2 C/W C/W 28.7 C/W 8.3 C/W 0.6 C/W JA Per JEDEC JESD51-2 JMA Per JEDEC JESD51-6 JB Per JEDEC JESD51-8 JC Per MIL-STD 883, Method 1012.1 JT Per JEDEC JESD51-2 Results are from simulations. The PCB is a JEDEC multilayer type. Thermal performance for actual applications requires careful inspection of the conditions in the application to determine if they are similar to those assumed in these calculations. Rev. B | Page 5 of 12 ADCLK954 40 39 38 37 36 35 34 33 32 31 VCC Q0 Q0 Q1 Q1 Q2 Q2 Q3 Q3 VCC PIN CONFIGURATION AND FUNCTION DESCRIPTIONS ADCLK954 TOP VIEW (Not to Scale) 30 29 28 27 26 25 24 23 22 21 VCC Q4 Q4 Q5 Q5 Q6 Q6 Q7 Q7 VCC NOTES 1. EPAD MUST BE SOLDERED TO VEE POWER PLANE. 07968-002 VCC Q11 Q11 Q10 Q10 Q9 Q9 Q8 Q8 VCC 11 12 13 14 15 16 17 18 19 20 IN_SEL 1 CLK0 2 CLK0 3 VREF 0 4 V T0 5 CLK1 6 CLK1 7 V T1 8 VREF 1 9 VEE 10 Figure 2. Pin Configuration Table 7. Pin Function Descriptions Pin No. 1 2 3 4 5 6 7 8 9 10 11, 20, 21, 30, 31, 40 12, 13 14, 15 16, 17 18, 19 22, 23 24, 25 26, 27 28, 29 32, 33 34, 35 36, 37 38, 39 Mnemonic IN_SEL CLK0 CLK0 VREF0 VT0 CLK1 CLK1 VT1 VREF1 VEE VCC Description Input Select. Logic 0 selects CLK0 and CLK0 inputs. Logic 1 selects CLK1 and CLK1 inputs. Differential Input (Positive) 0. Differential Input (Negative) 0. Reference Voltage. Reference voltage for biasing ac-coupled CLK0 and CLK0 inputs. Center Tap. Center tap of a 100 input resistor for CLK0 and CLK0 inputs. Differential Input (Positive) 1. Differential Input (Negative) 1. Center Tap. Center tap of a 100 input resistor for CLK1 and CLK1 inputs. Reference Voltage. Reference voltage for biasing ac-coupled CLK1 and CLK1 inputs. Negative Supply Pin. Positive Supply Pin. Q11, Q11 Q10, Q10 Q9, Q9 Q8, Q8 Q7, Q7 Q6, Q6 Q5, Q5 Q4, Q4 Q3, Q3 Q2, Q2 Q1, Q1 Q0, Q0 EPAD Differential LVPECL Outputs. Differential LVPECL Outputs. Differential LVPECL Outputs. Differential LVPECL Outputs. Differential LVPECL Outputs. Differential LVPECL Outputs. Differential LVPECL Outputs. Differential LVPECL Outputs. Differential LVPECL Outputs. Differential LVPECL Outputs. Differential LVPECL Outputs. Differential LVPECL Outputs. Exposed pad (EPAD) must be connected to VEE. Rev. B | Page 6 of 12 ADCLK954 TYPICAL PERFORMANCE CHARACTERISTICS VCC = 3.3 V, VEE = 0.0 V, VICM = VREF, TA = 25C, clock outputs terminated at 50 to VCC - 2 V, unless otherwise noted. C4 C3 C4 C3 C4 500ps/DIV 100mV/DIV Figure 3. LVPECL Output Waveform @ 200 MHz 07968-006 C3 07968-003 100mV/DIV 100ps/DIV Figure 6. LVPECL Output Waveform @ 1000 MHz 1.8 214 213 1.6 1.5 PROPAGATION DELAY (ps) DIFFERENTIAL OUTPUT VOLTAGE (V) 1.7 1.4 1.3 1.2 1.1 1.0 0.9 0.8 0.7 212 211 210 209 208 0.6 0 1000 2000 3000 4000 5000 FREQUENCY (MHz) 207 -40 07968-004 0.4 -20 0 20 40 60 07968-007 0.5 80 TEMPERATURE (C) Figure 4. Differential Output Voltage vs. Frequency, VID > 1.1 V p-p Figure 7. Propagation Delay vs. Temperature, VID = 1.6 V p-p 225 230 PROPAGATION DELAY (ps) 215 210 205 200 195 190 220 +85C 210 +25C 200 -40C 180 0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 DIFFERENTIAL INPUT VOLTAGE SWING (V) Figure 5. Propagation Delay vs. Differential Input Voltage 1.8 190 0.9 1.1 1.3 1.5 1.7 1.9 2.1 2.3 2.5 DC COMMON-MODE VOLTAGE (V) 2.7 2.9 3.1 07968-008 185 07968-005 PROPAGATION DELAY (ps) 220 Figure 8. Propagation Delay vs. DC Common-Mode Voltage vs. Temperature, Input Slew Rate > 25 V/ns Rev. B | Page 7 of 12 ADCLK954 -90 ABSOLUTE PHASE NOISE MEASURED @ 1GHz WITH AGILENT E5052 USING WENZEL CLOCK SOURCE CONSISTING OF A WENZEL 100MHz CRYSTAL OSCILLATOR (P/N 500-06672), WENZEL 5x MULTIPLIER (P/N LNOM-100-5-13-14-F-A), AND A WENZEL 2x MULTIPLIER (P/N LNDD-500-14-14-1-D). -100 -40C PHASE NOISE (dBc/Hz) 1.52 +25C 1.50 +85C 1.48 1.46 -110 -120 -130 ADCLK954 -140 -150 1.44 -160 1.42 2.75 -170 10 2.85 2.95 3.05 3.15 3.25 3.35 3.45 3.55 3.65 3.75 POWER SUPPLY (V) CLOCK SOURCE 10k 100k 1M 10M 100M Figure 11. Absolute Phase Noise Measured @1 GHz 300 500 450 ICC 250 RANDOM JITTER (fS rms) 400 350 +85C +25C -40C 300 250 200 200 150 100 50 150 3.0 3.1 3.2 3.3 3.4 SUPPLY VOLTAGE (V) 3.5 3.6 3.7 Figure 10. Power Supply Current vs. Power Supply Voltage vs. Temperature, All Outputs Loaded (50 to VCC - 2 V) Rev. B | Page 8 of 12 0 0 5 10 15 20 25 INPUT SLEW RATE (V/ns) Figure 12. RMS Random Jitter vs. Input Slew Rate, VID Method 07968-012 IEE 07968-010 SUPPLY CURRENT (mA) 1k FREQUENCY OFFSET (Hz) Figure 9. Differential Output Voltage Swing vs. Power Supply Voltage vs. Temperature, VID = 1.6 V p-p 100 2.9 100 07968-011 1.54 07968-009 DIFFERENTIAL OUTPUT VOLTAGE SWING (V) 1.56 ADCLK954 FUNCTIONAL DESCRIPTION Output jitter performance is degraded by an input slew rate below 4 V/ns, as shown in Figure 12. The ADCLK954 is specifically designed to minimize added random jitter over a wide input slew rate range. Whenever possible, clamp excessively large input signals with fast Schottky diodes because attenuators reduce the slew rate. Input signal runs of more than a few centimeters should be over low loss dielectrics or cables with good high frequency characteristics. LVPECL Y-termination is an elegant termination scheme that uses the fewest components and offers both odd- and even-mode impedance matching. Even-mode impedance matching is an important consideration for closely coupled transmission lines at high frequencies. Its main drawback is that it offers limited flexibility for varying the drive strength of the emitter follower LVPECL driver. This can be an important consideration when driving long trace lengths, but is usually not an issue. VS_DRV ADCLK954 VS = VS_DRV Z0 = 50 CLOCK OUTPUTS The specified performance necessitates using proper transmission line terminations. The LVPECL outputs of the ADCLK954 are designed to directly drive 800 mV into a 50 cable or into microstrip/stripline transmission lines terminated with 50 referenced to VCC - 2 V, as shown in Figure 14. The LVPECL output stage is shown in Figure 13. The outputs are designed for best transmission line matching. If high speed signals must be routed more than a centimeter, either the microstrip or the stripline technique is required to ensure proper transition times and to prevent excessive output ringing and pulse width dependent propagation delay dispersion. 50 VCC - 2V 50 LVPECL 07968-014 The ADCLK954 accepts a differential clock input from one of two inputs and distributes the selected clock to all 12 LVPECL outputs. The maximum specified frequency is the point at which the output voltage swing is 50% of the standard LVPECL swing (see Figure 4). See the functional block diagram (Figure 1) and the General Description section for more clock input details. See Figure 19 through Figure 22 for various clock input termination schemes. Thevenin-equivalent termination uses a resistor network to provide 50 termination to a dc voltage that is below VOL of the LVPECL driver. In this case, VS_DRV on the ADCLK954 should equal VS of the receiving buffer. Although the resistor combination shown (in Figure 15) results in a dc bias point of VS_DRV - 2 V, the actual common-mode voltage is VS_DRV - 1.3 V because there is additional current flowing from the ADCLK954 LVPECL driver through the pull-down resistor. Z0 = 50 Figure 14. DC-Coupled, 3.3 V LVPECL VS_DRV VS_DRV ADCLK954 50 127 127 SINGLE-ENDED (NOT COUPLED) VS LVPECL 50 83 83 07968-015 CLOCK INPUTS VCC Figure 15. DC-Coupled, 3.3 V LVPECL Far-End Thevenin Termination ADCLK954 VS = VS_DRV Z0 = 50 50 Q 50 50 LVPECL 07968-016 VS_DRV Z0 = 50 Q VS_DRV ADCLK954 VS 0.1nF Figure 13. Simplified Schematic Diagram of the LVPECL Output Stage Figure 14 through Figure 17 depict various LVPECL output termination schemes. When dc-coupled, VS of the receiving buffer should match the VS_DRV. 100 DIFFERENTIAL 100 (COUPLED) 0.1nF TRANSMISSION LINE 200 LVPECL 200 Figure 17. AC-Coupled, LVPECL with Parallel Transmission Line Rev. B | Page 9 of 12 07968-017 VEE 07968-013 Figure 16. DC-Coupled, 3.3 V LVPECL Y-Termination ADCLK954 A Logic 0 on the IN_SEL pin selects the Input CLK0 and Input CLK0. A Logic 1 on the IN_SEL pin selects Input CLK1 and Input CLK1. PCB LAYOUT CONSIDERATIONS The ADCLK954 buffer is designed for very high speed applications. Consequently, high speed design techniques must be used to achieve the specified performance. It is critically important to use low impedance supply planes for both the negative supply (VEE) and the positive supply (VCC) planes as part of a multilayer board. Providing the lowest inductance return path for switching currents ensures the best possible performance in the target application. The following references to GND plane assume that the VEE power plane is grounded for LVPECL operation. Note that for ECL operation, the VCC power plane becomes the ground plane. It is also important to adequately bypass the input and output supplies. Place a 1 F electrolytic bypass capacitor within several inches of each VCC power supply pin to the GND plane. In addition, place multiple high quality 0.001 F bypass capacitors as close as possible to each of the VCC supply pins and connect the capacitors to the GND plane with redundant vias. Carefully select high frequency bypass capacitors for minimum inductance and ESR. To improve the effectiveness of the bypass at high frequencies, minimize parasitic layout inductance. Also, avoid discontinuities along input and output transmission lines that can affect jitter performance. If the return is floated, the device exhibits a 100 cross termination, but the source must then control the common-mode voltage and supply the input bias currents. There are ESD/clamp diodes between the input pins to prevent the application from developing excessive offsets to the input transistors. ESD diodes are not optimized for best ac performance. When a clamp is required, it is recommended that appropriate external diodes be used. Exposed Metal Paddle The exposed metal paddle on the ADCLK954 package is both an electrical connection and a thermal enhancement. For the device to function properly, the paddle must be properly attached to the VEE power plane. When properly mounted, the ADCLK954 also dissipates heat through its exposed paddle. The PCB acts as a heat sink for the ADCLK954. The PCB attachment must provide a good thermal path to a larger heat dissipation area. This requires a grid of vias from the top layer down to the VEE power plane (see Figure 18). The ADCLK954 evaluation board (ADCLK954/PCBZ) provides an example of how to attach the part to the PCB. In a 50 environment, input and output matching have a significant impact on performance. The buffer provides internal 50 termination resistors for both CLKx and CLKx inputs. Normally, the return side is connected to the reference pin that is provided. Carefully bypass the termination potential using ceramic capacitors to prevent undesired aberrations on the input signal due to parasitic inductance in the termination return path. If the inputs are dccoupled to a source, take care to ensure that the pins are within the rated input differential and common-mode ranges. Rev. B | Page 10 of 12 VIAS TO VEE POWER PLANE 07968-018 CLOCK INPUT SELECT (IN_SEL) SETTINGS Figure 18. PCB Land for Attaching Exposed Paddle ADCLK954 INPUT TERMINATION OPTIONS VREF VREF VT VT 50 CLK 50 50 CLK CLK 50 07968-019 CLK CONNECT VT TO VCC. CONNECT VT TO VREF . Figure 19. Interfacing to CML Inputs 07968-021 VCC Figure 21. AC Coupling Differential Signals Inputs, Such As LVDS VREF VT 50 CLK VREF VT 50 CLK VCC - 2V 50 CLK 50 07968-020 CONNECT VT TO VCC - 2V. CONNECT VT, VREF , AND CLK. PLACE A BYPASS CAPACITOR FROM VT TO GROUND. ALTERNATIVELY, VT, VREF , AND CLK CAN BE CONNECTED, GIVING A CLEANER LAYOUT AND A 180 PHASE SHIFT. Figure 20. Interfacing to PECL Inputs 07968-022 CLK Figure 22. Interfacing to AC-Coupled Single-Ended Inputs Rev. B | Page 11 of 12 ADCLK954 OUTLINE DIMENSIONS 6.00 BSC SQ 0.60 MAX 0.60 MAX PIN 1 INDICATOR 5.75 BSC SQ 0.50 BSC 20 19 PIN 1 INDICATOR 3.05 2.90 SQ 2.75 11 10 0.25 MIN 0.80 MAX 0.65 TYP 0.30 0.23 0.18 4.50 REF 0.05 MAX 0.02 NOM COPLANARITY 0.08 0.20 REF FOR PROPER CONNECTION OF THE EXPOSED PAD, REFER TO THE PIN CONFIGURATION AND FUNCTION DESCRIPTIONS SECTION OF THIS DATA SHEET. COMPLIANT TO JEDEC STANDARDS MO-220-VJJD-2 082708-A SEATING PLANE 1 BOTTOM VIEW TOP VIEW 12 MAX 40 EXPOSED PAD 0.50 0.40 0.30 1.00 0.85 0.80 29 28 Figure 23. 40-Lead Lead Frame Chip Scale Package [LFSCP_VQ] 6 mm x 6 mm Body, Very Thin Quad (CP-40-8) Dimensions shown in millimeters ORDERING GUIDE Model 1 ADCLK954BCPZ ADCLK954BCPZ-REEL7 ADCLK954/PCBZ 1 Temperature Range -40C to +85C -40C to +85C Package Description 40-Lead LFCSP_VQ 40-Lead LFCSP_VQ Evaluation Board Z = RoHS Compliant Part. (c)2009-2010 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. D07968-0-6/10(B) Rev. B | Page 12 of 12 Package Option CP-40-8 CP-40-8