SIL06-05SADJ-H - Artesyn Embedded Technologies

DC/DC CONVERTERS 6A Non-isolated DC/DC Converters 1

2 YEAR WARRANTY

SIL06 Series

Single output

•Ultra wide trim range 0.9V to 3.3V/5.0V

•Current sink capability for termination application

•Horizontal and vertical-mount options available

•High power density design means reduced board space

requirement

•Power good output signal (open collector)

•Operating ambient temperature up to +80ºC with suitable

derating and forced air cooling

•Remote ON/OFF (active high)

•0A minimum load

•Input under-voltage lockout

•Over-current and short-circuit protection

The SIL06 Series is a new high density open frame non-isolated converter for space

sensitive applications. Each model has a wide input range (4.5 - 5.5VDC or 10.2 -

13.8VDC) and offer a wide 0.9 - 5V output voltage range with a 6A load. An external

resistor adjusts the output voltage from its pre-set value of 0.9V to any value up to the

5V maximum. Typical efficiencies for the models are 89% for the 5V input version and

91% for the 12V input version. The SIL06 series offers remote ON/OFF and over-

current protection as standard. With full international safety approval including

EN60950 and UL/cUL60950, the SIL06 reduces compliance costs and time to market.

NEW Product

All specifications are typical at nominal input, full load at 25°C unless otherwise stated SPECIFICATIONS

OUTPUT SPECIFICATIONS

Voltage adjustability 5V input models 0.9V to 3.3V

(See Note 7) 12V input models 0.9V to 5.0V

Output setpoint accuracy With 1.0% trim resistors ±2.5%

Line regulation Low line to high line ±0.2% max.

Load regulation Full load to min. load ±0.5% max.

Min./max. load 0A/6A

Overshoot 5V input models 3.0% max.

(at turn on) 12V input models 1.0% max.

Undershoot 100mV max.

Ripple and noise 5Hz to 20MHz (See Note 2) See table

Transient response Deviation 75mV

(See Note 1) 150µs recovery to

within regulation band

INPUT SPECIFICATIONS

Input voltage range 5V input model 4.5 to 5.5VDC

12V input model 10.2 to 13.8VDC

Input current No load 50mA

Remote OFF 5mA

Input current (max.) 5V input model 5.1A @ Io max.

(See Note 9) 12V input model 1.6A @ Io max.

Input reflected ripple 5V input model 52mA (pk-pk)

(See Note 2) 12V input model 56mA (pk-pk)

Remote ON/OFF

Logic compatibility Active high

ON >2.4VDC

OFF <0.8VDC

Start-up time Power up <20ms

(See Note 3) Remote ON/OFF <20ms

File Name: SIL06.PDF Rev: 31 Jan 2003

INPUT SPECIFICATIONS Contd.

Turn ON threshold 5Vin model 4.5V

12Vin model 9.0V

Turn OFF threshold 5Vin model 4.3V

12Vin model 7.5V

GENERAL SPECIFICATIONS

Efficiency See table

Switching frequency Fixed 200kHz

Approvals and TÜV Product Service

standards (See Note 4) IEC60950, UL/cUL60950

Material flammability UL94V-0

Weight 9.3g (0.3oz)

MTBF MIL-HDBK-217F 1,307,257 hours

Representative model: 12V model @ 40ºC

100% load, ground benign

Bellcore 332 7, 562,142 hours

ENVIRONMENTAL SPECIFICATIONS

Thermal performance Operating ambient, 0°C to +80°C

(See Note 10) temperature

Non-operating -40°C to +125°C

Altitude derating 3,000m (9,843 ft) 20%

(above sea level) 10,000m (32,808 ft) 50%

International Safety Standard Approvals

UL/cUL CAN/CSA 22.2 No. E139421

UL60950 file No. E139421

TÜV TÜV Product Service (EN60950) Certificate No. B0211 19870 205

CB report and certificate to IEC60950

Notes

1di/dt = 10A/µs, Vin = Nom, Tc = 25°C, load change = 0.5 lo max. to 0.75

lo max. and 0.75 lo max. to 0.5 lo max.

2Measured with external filter. See Application Note 131 for details.

3Power up is the time from application of DC input to Power Good

enabled. Remote ON/OFF is from ON/OFF asserted high to Power Good

enabled

4This product is only for inclusion by professional installers within other

equipment and must not be operated as a stand alone product.

5The standard unit with the suffix '-V' is for vertical mounting. To order a

unit with horizontal mounting, please add the suffix '-H' to the model

number, e.g. SIL06-05SADJ-H.

6Measured as per recommended set-up. Cin = 270µF (20mΩ esr max.).

Cout = 680µF (10mΩ esr max.).

7Uses external resistor from trim to output ground. Minimum value 485Ω

for 5V model, 280Ω for 12V model. See Applications Note 131 for

details.

8Signal line assumed <3m.

9External input fusing recommended.

10 See Application Note 131 for operation above 50ºC.

11 See Application Note 131 for more details.

12 These models have a wide trim output. 5Vin has an output of 0.9V to

3.3V and 12 Vin has an output of 0.9V to 5V. An external resistor adjusts

the output voltage.

For the most current data and application support visit www.artesyn.com/powergroup/products.htm

CAUTION: High internal temperatures. Ensure that unit is not user

accessible.

SIL06 Series

Single Output

DC/DC CONVERTERS 6A Non-isolated DC/DC Converters 2

NEW Product

OUTPUT INPUT OVP OUTPUT OUTPUT OUTPUT EFFICIENCY REGULATION MODEL

POWER VOLTAGE VOLTAGE(12) CURRENT CURRENT (TYP.) LINE LOAD NUMBER (5)

(MAX.) (MIN.) (MAX.)

20W 4.5-5.5VDC N/A 0.9V - 3.3V 0A 6A 89% ±0.2% ±0.5% SIL06-05SADJ-V

30W 10.2-13.8VDC N/A 0.9V - 5.0V 0A 6A 91% ±0.2% ±0.5% SIL06-12SADJ-V

Ripple and Noise Specification

PIN CONNECTIONS

PIN NUMBER FUNCTION

1Vout

2Trim

3Ground

4Power Good

5Remote ON/OFF

6Vin

7Mechanical support

8Mechanical support

9Mechanical support on

horizontal version only

Please consult our website for the following items: ✔ Application Note ✔ Longform Data Sheet www.artesyn.com

Output

Model Voltage Pk - Pk RMS

5V input models 0.9 to 2.5V 30mV 15mV

3.3V 40mV 15mV

12V input models 0.9 to 2.5V 40mV 20mV

3.3 to 5V 50mV 20mV

PROTECTION

Short-circuit protection Hiccup, non-latching

RECOMMENDED SYSTEM CAPACITANCE

Input capacitance (See Note 11) 270µF/20mΩ esr max.

Output capacitance (See Note 11) 680µf/10mΩ esr max.

File Name: SIL06.PDF Rev: 31 Jan 2003

For the most current data and application support visit www.artesyn.com/powergroup/products.htm

SIL06 Series

Single Output

DC/DC CONVERTERS 6A Non-isolated DC/DC Converters 3

NEW Product

All dimensions in INCHES (mm)

General tolerance ±0.01in (±0.25mm)

except where specified otherwise

1.200

(30.48)

0.610

(15.49)

0.527

(13.38)

0.025

(0.64) Typ.

Mechanical

Support Pin

0.062

(1.57)

PCB Ref.

PIN 8

0.025

(0.64) Typ.

PIN 1

0.315

(8.00 max.)

0.150

(3.81) Ref.

0.120

(3.05)

9 Places

Figure 1: Mechanical Drawing - Horizontal Mount Version

Figure 2: Mechanical Drawing - Vertical Mount Version

All dimensions in inches (mm)

General tolerance ±0.01in (±0.25mm)

except where specified otherwise

0.070

(1.78)

0.315

(8.00) max.

Pin 1

Pin 8

0.025

(0.64)

0.610

(15.49)

1.200

(30.48)

0.040

(1.02) Ref.

0.150

(3.81)

8 Places

0.062

(1.57) Ref.

0.050

(1.27)

0.025

(0.64) Typ.

2003

The information and specifications contained in this data sheet are believed to be correct at time of publication. However, Artesyn Technologies accepts no responsibility for consequences arising

from printing errors or inaccuracies. Specifications are subject to change without notice. No rights under any patent accompany the sale of any such product(s) or information contained herein.

Please consult our website for the following items: ✔ Application Note ✔ Longform Data Sheet www.artesyn.com

File Name: SIL06.PDF Rev: 31 Jan 2003