LP3921 LP3921 Battery Charger Management and Regulator Unit with Integrated Boomer Audio Amplifier Literature Number: SNVS580 LP3921 Battery Charger Management and Regulator Unit with Integrated Boomer(R) Audio Amplifier General Description Features The LP3921 is a fully integrated charger and multi-regulator unit with a fully differential Boomer audio power amplifier designed for CDMA cellular phones. The LP3921 has a highspeed serial interface which allows for the integration and control of a Li-Ion battery charger, 7 low-noise low-dropout (LDO) voltage regulators and a Boomer audio amplifier. The Li-Ion charger integrates a power FET, reverse current blocking diode, sense resistor with current monitor output, and requires only a few external components. Charging is thermally regulated to obtain the most efficient charging rate for a given ambient temperature. LDO regulators provide high PSRR and low noise ideally suited for supplying power to both analog and digital loads. The Boomer Audio Amplifier is capable of delivering 1.1 watts of continuous average power to an 8 BTL load with less than 1% distortion (THD+N). Boomer Audio Power Amplifiers were designed specifically to provide high quality output power with a minimal amount of external components. The Boomer Audio Amplifier does not require output coupling capacitors or bootstrap capacitors, and therefore is ideally suited for mobile phone and other low voltage applications where minimal power consumption and part count is the primary requirement. The Boomer Audio Amplifier contains advanced pop & click circuitry which eliminates noises during turn-on and turn-off transitions. Charger -- DC adapter or USB input -- Thermally regulated Charge Current -- Under Voltage Lockout -- 50 to 950 mA Programmable Charge Current 3.0V to 5.5V Input Voltage Range Thermal shutdown I2C-compatible Interface for controlling Charger, LDO outputs and enabling Audio output LDO's 7 Low-Noise LDO's -- 2 x 300 mA -- 3 x 150 mA -- 2 x 80 mA 2% (typ.) Output Voltage Accuracy on LDO's Audio -- Fully Differential Amplification -- Ability to drive capacitive loads up to 100 pF -- No output coupling capacitors, snubber networks or bootstrap capacitors required Space- Efficient 32-pin 5 x 5 mm LLP package Applications CDMA Phone Handsets Low Power Wireless Handsets Handheld Information Appliances Personal Media Players Boomer(R) is a registered trademark of National Semiconductor Corporation. (c) 2008 National Semiconductor Corporation 300698 www.national.com LP3921 Battery Charger Management and Regulator Unit with Integrated Boomer Audio Amplifier August 26, 2008 LP3921 System Diagram 30069801 www.national.com 2 LP3921 Functional Block Diagram 30069802 3 www.national.com LP3921 Connection Diagram - Device Pin Diagram 30069803 * Date code is in UZXYTT format where: * * * * U - Wafer Fab Code Z - Assembly Plant XY - 2-Digit Date Code TT - Lot Traceability Ordering Information Order Number SPEC Package Marking Supplied As LP3921SQE NOPB L3921SQ 250 units, Tape & Reel LP3921SQ NOPB L3921SQ 1000 units, Tape & Reel LP3921SQX NOPB L3921SQ 4500 units, Tape & Reel www.national.com 4 The LP3921 Charge Management and Regulator Unit is designed to supply charger and voltage output capabilities for mobile systems, e.g. CDMA handsets. The device provides a Li-Ion charging function and 7 regulated outputs. Communication with the device is via an I2C compatible serial interface that allows function control and status read-back. The battery charge management section provides a programmable CC/CV linear charge capability. Following a normal charge cycle a maintenance mode keeps battery voltage between programmable levels. Power levels are thermally regulated to obtain optimum charge levels over the ambient temperature range. POWER SUPPLY CONFIGURATIONS At PMU start up, LDO1, LDO2 and LDO3 are always started with their default voltages. The start up sequence of the LDO's is given below. Startup Sequence LDO1 -> LDO2 -> LDO3 LDO's with external enable control (LDO4, LDO5, LDO6) start immediately after LDO2 if enabled by logic high at their respective control inputs. LDO7 (and LDO1, LDO3) may be programmed to enable/disable once PS_HOLD has been asserted. CHARGER FEATURES * Pre-charge, CC, CV and Maintenance modes * USB Charge 100 mA/450 mA * Integrated FET * Integrated Reverse Current Blocking Diode * Integrated Sense Resistor * Thermal regulation * Charge Current Monitor Output * Programmable charge current 50 mA - 950 mA with 50 mA steps * Default CC mode current 100 mA * Pre-charge current fixed 50 mA * Termination voltage 4.1V, 4.2V (default), 4.3V, and 4.4V, accuracy better than +/- 0.35% (typ.) * Restart level 100 mV, 150 mV (default) and 200 mV below Termination voltage * Programmable End of Charge 0.1C (default), 0.15C, 0.2C and 0.25C * Enable Control Input * Safety timer * Input voltage operating range 4.5V - 6.0V DEVICE PROGRAMMABILITY An I2C compatible Serial Interface is used to communicate with the device to program a series of registers and also to read status registers. These internal registers allow control over LDO outputs and their levels. The charger functions may also be programmed to alter termination voltage, end of charge current, charger restart voltage, full rate charge current, and also the charging mode. This device internal logic is powered from LDO2. TABLE 1. LDO Default Voltages LDO Function mA Default Voltage (V) Startup Default Enable Control 1 CORE 300 1.8 ON SI 2 DIGI 300 3.0 ON - 3 ANA 80 3.0 ON SI 4 TCXO 80 3.0 OFF TCXO_EN 5 RX 150 3.0 OFF RX_EN 6 TX 150 3.0 OFF TX_EN 7 GP 150 3.0 OFF SI TABLE 2. LDO Output Voltages Selectable via Serial Interface mA 1.5 1.8 1.85 2.5 2.6 3.2 3.3 1 LDO CORE 300 + + + + + + + + + + + + + + + + 2 DIGI 300 + + + + + + + + + + + + + 3 ANA 80 + + + + + + + + 4 TCXO 80 + + + + + + + + + + + 5 RX 150 + + + + + + + + 6 TX 150 + + + + + + + + 7 GP 150 + + + + + + + + + + + + + + + + + + + + + 2.7 2.75 2.8 2.85 2.9 2.95 3.0 3.05 3.1 5 www.national.com LP3921 REGULATORS Seven low-dropout linear regulators provide programmable voltage outputs with current capabilities of 80 mA, 150 mA and 300 mA as given in the table below. LDO1, LDO2 and LDO3 are powered up by default with LDO1 reaching regulation before LDO2 and LDO3 are started. LDO1, LDO3 and LDO7 can be disabled/enabled via the serial interface. LDO1 and LDO2, if enabled, must be in regulation for the device to power up and remain powered. LDO4, LDO5 and LDO6 have external enable pins and may power up following LDO2 as determined by their respective enable. Under voltage lockout oversees device start up with preset level of 2.85V (typ.). Device Description LP3921 LP3921 Pin Descriptions Pin# Name Type 1 LDO6 A Description LDO6 Output (TX) 2 TX_EN DI Enable control for LDO6 (TX). HIGH = Enable, LOW = Disable 3 LDO5 A A LDO5 Output (RX) 4 VIN2 P Battery Input for LDO3 - LDO7 5 LDO7 A LDO7 Output (GP) 6 OUT+ AO Differential output + 7 VDD P 8 OUT- AO Differential output - 9 IN+ AI Differential input + 10 IN- AI Differential input - 11 GND G Analog Ground Pin 12 BYPASS A Amplifier bypass cap 13 LDO4 A LDO4 Output (TCXO) 14 LDO3 A LDO3 Output (ANA) 15 LDO2 A LDO2 Output (DIGI) 16 LDO1 A LDO1 Output (CORE) 17 VIN1 P Battery Input for LDO1 and LDO2 18 GNDA G Analog Ground pin DC power input to audio amplifier SDA DI/O 20 SCL DI Serial Interface Clock input. External pull up resistor is needed. (typ. 1.5k) 21 BATT P Main battery connection. Used as a power connection for current delivery to the battery. 22 CHG_IN P DC power input to charger block from wall or car power adapters. 23 PWR_ON DI Power up sequence starts when this pin is set HIGH. Internal 500k. pull-down resistor. IMON A Charge current monitor output. This pin presents an analog voltage representation of the 25 PS_HOLD DI Input for power control from external processor/controller. 26 TCXO_EN DI Enable control for LDO4 (TX). HIGH = Enable, LOW = Disable. 27 HF_PWR DI Power up sequence starts when this pin is set HIGH. Internal 500k. pull-down resistor. 28 VSS G Digital Ground pin 29 PON_N DO Active low signal is PWR_ON inverted. RESET_N DO Reset Output. Pin stays LOW during power up sequence. 60 ms after LDO1 (CORE) is stable this pin is asserted HIGH. 31 ACOK_N DO AC Adapter indicator, LOW when 4.5V- 6.0V present at CHG_IN. 32 RX_EN DI Enable control for LDO5 (RX). HIGH = Enable, LOW = Disable. 19 24 Serial Interface, Data Input/Output Open Drain output, external pull up resistor is needed. (typ. 1.5k) input charging current. VIMON (mV) = (2.47 x ICHG)(mA). 30 Key: A=Analog; D=Digital; I=Input; DI/O=Digital-Input/Output; G=Ground; O=Output; P=Power www.national.com 6 Operating Ratings If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. -0.3 to +6.0V -0.3 to VBATT +0.3V, max 6.0V 150C -40C to +150C CHG_IN (Note 10) VBATT =VIN1/2, BATT, VDD HF_PWR, PWR_ON ACOK_N, SDA, SCL, RX_EN, TX_EN, TCXO_EN, PS_HOLD, RESET_N All other pins Junction Temperature (TJ) Ambient Temperature (TA) (Note 5) Internally Limited Thermal Properties CHG-IN VBATT =VIN1/2, BATT, VDD, HF_PWR All other Inputs Junction Temperature (TJ-MAX) Storage Temperature Max Continuous Power Dissipation (PD-MAX) (Note 3) ESD (Note 4) BATT, VIN1, VIN2, VDD, HF_PWR, CHG_IN, PWR_ON All other pins -0.3 to +6.5V (Notes 1, 2) 4.5 to 6.0V 3.0 to 5.5V 0V to 5.5V 0V to (VLDO2 + 0.3V) 0V to (VBATT + 0.3V) -40C to +125C -40 to 85C (Note 9) Junction to Ambient Thermal Resistance JA 8 kV HBM 2 kV HBM 4L Jedec Board 30 C/W General Electrical Characteristics Unless otherwise noted, VIN (=VIN1=VIN2=BATT=VDD) = 3.6V, GND = 0V, CVIN1-2=10 F, CLDOX=1 F. Typical values and limits appearing in normal type apply for TJ = 25C. Limits appearing in boldface type apply over the entire junction temperature range for operation, TA = TJ = -40C to +125C. (Note 6) Symbol IQ(STANDBY) Parameter Standby Supply Current Condition Typ VIN = 3.6V, UVLO on, internal logic circuit on, all other circuits off 2 Limit Min Units Max 5 A 3.0 V POWER MONITOR FUNCTIONS Battery Under-Voltage Lockout VUVLO-R Under Voltage Lock-out VIN Rising 2.85 (Note 7) 160 2.7 THERMAL SHUTDOWN Higher Threshold C LOGIC AND CONTROL INPUTS VIL VIH Input Low Level Input High Level IIL Logic Input Current RIN Input Resistance PS_HOLD, SDA, SCL, RX_EN, TCXO_EN, TX_EN (Note 7) 0.25* VLDO2 V PWR_ON, HF_PWR (Note 7) 0.25* VBATT V PS_HOLD, SDA, SCL, RX_EN, TCXO_EN, TX_EN (Note 7) 0.75* VLDO2 V PWR_ON, HF_PWR (Note 7) 0.75* VBATT V All logic inputs except PWR_ON and HF_PWR -5 A +5 0V VINPUT VBATT PWR_ON, HF_PWR Pull-Down resistance to GND 500 k LOGIC AND CONTROL OUTPUTS VOL Output Low Level PON_N, RESET_N, SDA, ACOK_N IOUT = 2 mA VOH Output High Level PON_N, RESET_N, ACOK_N IOUT = -2 mA 0.25* VLDO2 0.75* VLDO2 V V (Not applicable to Open Drain Output SDA) 7 www.national.com LP3921 Absolute Maximum Ratings (Notes 1, 2) LP3921 LDO1 (CORE) Electrical Characteristics Unless otherwise noted, VIN (=VIN1=VIN2=BATT=VDD) = 3.6V, GND = 0V, CVIN1-2=10 F, CLDOX=1 F. Note VINMIN is the greater of 3.0V or VOUT1+ 0.5V. Typical values and limits appearing in normal type apply for TJ = 25C. Limits appearing in boldface type apply over the entire junction temperature range for operation, TA = TJ = -40C to +125C. (Note 6) Symbol VOUT1 IOUT1 Parameter Output Voltage Accuracy Condition Typ IOUT1 = 1 mA, VOUT1= 3.0V Output Voltage Default Output Current VINMIN VIN 5.5V Limit Min Max -2 +2 -3 +3 1.8 Output Current Limit VOUT1 = 0V 600 VDO1 Dropout Voltage IOUT1 = 300 mA (Note 8) 220 VOUT1 Line Regulation VINMIN VIN 5.5V Units % V 300 mA 310 mV 2 mV IOUT1 = 1 mA Load Regulation 1 mA IOUT1 300 mA 10 mV en1 Output Noise Voltage 10 Hz f 100 kHz, 45 VRMS PSRR Power Supply Rejection Ratio F = 10 kHz, COUT = 1 F 65 dB Start-Up Time from Internal Enable COUT = 1 F, IOUT1 = 300 mA Start-Up Transient Overshoot COUT = 1 F, IOUT1 = 300 mA (Note 7) COUT = 1 F (Note 7) tSTART-UP TTransient www.national.com IOUT1 = 20 mA (Note 7) 60 170 s 60 120 mV (Note 7) 8 Unless otherwise noted, VIN (=VIN1=VIN2=BATT=VDD) = 3.6V, GND = 0V, CVIN1-2=10 F, CLDOX=1 F. Note VINMIN is the greater of 3.0V or VOUT2+ 0.5V. Typical values and limits appearing in normal type apply for TJ = 25C. Limits appearing in boldface type apply over the entire junction temperature range for operation, TA = TJ = -40C to +125C. (Note 6) Symbol VOUT2 IOUT2 Parameter Output Voltage Accuracy Condition Typ IOUT2 = 1 mA, VOUT2= 3.0V Output Voltage Default Output Current VINMIN VIN 5.5V Limit Min Max -2 +2 -3 +3 3 Output Current Limit VOUT2 = 0V 600 VDO2 Dropout Voltage IOUT2 = 300 mA (Note 8) 220 VOUT2 Line Regulation VINMIN VIN 5.5V Units % V 300 mA 310 mV 2 mV IOUT2 = 1mA Load Regulation 1 mA IOUT2 300 mA 10 mV en2 Output Noise Voltage 10 Hz f 100 kHz, 45 VRMS PSRR Power Supply Rejection Ratio F = 10 kHz, COUT = 1 F 65 dB tSTART-UP Start-Up Time from Shutdown COUT = 1 F, IOUT2 = 300 mA (Note 7) 40 60 s tTransient Start-Up Transient Overshoot COUT = 1 F, IOUT2 = 300 mA (Note 7) 5 30 mV COUT = 1 F (Note 7) IOUT2 = 20 mA (Note 7) LDO3 (ANA), LDO4 (TCXO) Electrical Characteristics Unless otherwise noted, VIN (=VIN1=VIN2=BATT=VDD) = 3.6V, GND = 0V, CVIN1-2=10 F, CLDOX=1 F. TCXO_EN high. Note VINMIN is the greater of 3.0V or VOUT3/4 + 0.5V. Typical values and limits appearing in normal type apply for TJ = 25C. Limits appearing in boldface type apply over the entire junction temperature range for operation, TA = TJ = -40C to +125C. (Note 6) Symbol VOUT3, VOUT4 Parameter Condition Typ Output Voltage Accuracy IOUT3/4 = 1 mA, VOUT3/4= 3.0V Output Voltage LDO3 default 3 LDO4 default 3 Output Current VINMIN VIN 5.5V Output Current Limit VOUT3/4 = 0V 160 VDO3, VDO4 Dropout Voltage IOUT3/4 = 80 mA (Note 8) 220 VOUT3 , Line Regulation VINMIN VIN 5.5V IOUT3, IOUT4 VOUT4 Limit Min Max -2 +2 -3 +3 Units % V 80 mA 310 mV 2 mV IOUT3/4 = 1 mA Load Regulation 1mA IOUT3/4 80 mA 5 mV en3,en4 Output Noise Voltage 10 Hz f 100 kHz, COUT = 1 F (Note 7) 45 VRMS PSRR Power Supply Rejection Ratio F = 10 kHz, COUT = 1 F 65 dB IOUT3/4 = 20 mA (Note 7) tSTART-UP Start-Up Time from Enable COUT = 1 F, IOUT3/4 = 80mA (Note 7) 40 60 s tTransient Start-Up Transient Overshoot 5 30 mV COUT = 1F, IOUT3/4 = 80 mA (Note 7) 9 www.national.com LP3921 LDO2 (DIGI) Electrical Characteristics LP3921 LDO5 (RX), LDO6 (TX), LDO7 (GP) Electrical Characteristics Unless otherwise noted, VIN (=VIN1=VIN2=BATT=VDD) = 3.6V, GND = 0V, CVIN1-2=10 F, CLDOX=1 F. RX_EN, TX_EN high. LDO7 Enabled via Serial Interface. Note VINMIN is the greater of 3.0V or VOUT5/6/7 + 0.5V. Typical values and limits appearing in normal type apply for TJ = 25C. Limits appearing in boldface type apply over the entire junction temperature range for operation, TA = TJ = -40C to +125C. (Note 6) Symbol VOUT5, VOUT6, VOUT7 Parameter Output Voltage Default Output Voltage Condition Typ IOUT5/6/7 = 1mA, VOUT5/6/7= 3.0V LDO5 3 LDO6 3 LDO7 3 IOUT5, IOUT6, IOUT7 Output Current VINMIN VIN 5.5V Output Current Limit VOUT5/6/7 = 0V 300 VDO5, VDO6, VDO7 Dropout Voltage IOUT5/6/7 = 150 mA (Note 8) 200 VOUT5, Line Regulation VINMIN VIN 5.5V VOUT6, Limit Min Max -2 +2 -3 +3 Units % V 150 mA 280 mV 2 mV IOUT5/6/7 = 1 mA VOUT7 Load Regulation 1mA IOUT5/6/7 150 mA 10 mV en5, en6, en7 Output Noise Voltage 10 Hz f 100 kHz, COUT = 1 F (Note 7) 45 VRMS PSRR Power Supply Rejection Ratio F = 10 kHz, COUT = 1 F 65 dB tSTART-UP Start-Up Time from Enable COUT = 1 F, IOUT5/6/7 = 150 mA (Note 7) 40 60 s tTransient Start-Up Transient Overshoot 5 30 mV www.national.com IOUT5/6/7 = 20 mA (Note 7) COUT = 1 F, IOUT5/6/7 = 150 mA (Note 3) 10 Unless otherwise noted, VCHG-IN = 5V, VIN (=VIN1=VIN2=BATT=VDD) = 3.6V.CCHG_IN = 10 F. Charger set to default settings unless otherwise noted. Typical values and limits appearing in normal type apply for TJ = 25C. Limits appearing in boldface type apply over the entire junction temperature range for operation, TA = TJ = -25C to +85C. (Notes 6, 9) Symbol VCHG-IN Parameter Input Voltage Range Condition Typ (Note 7) Operating Range VOK_CHG VTERM ICHG CHG_IN OK trip-point Limit Min Max 4.5 6.5 4.5 6 Units V VCHG_IN - VBATT (Rising) 200 VCHG_IN - VBATT (Falling) 50 Battery Charge Termination voltage Default 4.2 VTERM voltage tolerance TJ = 0C to 85C -1 +1 % Fast Charge Current Accuracy ICHG = 450 mA -10 +10 % 50 950 mA 40 60 mA Programmable full-rate 6.0V VCHG_IN 4.5V charge current range (default V BATT < (VCHG_IN - VOK_CHG) 100 mA) VFULL_RATE < VBATT < VTERM mV V (Note 10) Default 100 Charge current programming step 50 IPREQUAL Pre-qualification current VBATT = 2V ICHG_USB CHG_IN programmable current in USB mode 50 5.5V VCHG_IN 4.5V Low 100 VBATT < (VCHG_IN VOK_CHG) VFULL_RATE < VBATT < VTERM High Default = 100 mA mA 450 100 VFULL_RATE Full-rate qualification threshold VBATT rising, transition from prequal to full-rate charging 3 IEOC End of Charge Current, % of full-rate current 0.1C option selected 10 VRESTART Restart threshold voltage VBATT falling, transition from EOC to full-rate charge mode. Default options selected - 4.05V 4.05 IMON Voltage 1 ICHG = 100 mA 0.247 IMON Voltage 2 ICHG = 450 mA 1.112 Regulated junction temperature (Note 7) 115 IMON TREG 2.9 3.1 V % 3.97 4.13 V 0.947 1.277 V C Detection and Timing (Note 7) TPOK Power OK deglitch time VBATT < (VCC - VOK_CHG) 32 mS TPQ_FULL Deglitch time Pre-qualification to full-rate charge transition 230 mS TCHG Charge timer Precharge mode 1 Hrs Charging Timeout 5 TEOC Deglitch time for end-ofcharge transition 230 11 mS www.national.com LP3921 Charger Electrical Characteristics LP3921 Audio Electrical Characteristics Unless otherwise noted, VDD= 3.6V Typical values and limits appearing in normal type apply for TJ = 25C. Limits appearing in boldface type apply over the entire junction temperature range for operation, TA= TJ = -25C to +85C. (Note 6) Symbol Paramater Conditions Typical Limit Min Max Units PO Output Power THD = 1% (max); f = 1 kHz, RL = 8 0.375 W THD + N Total Harmonic Distortion + Noise PO = 0.25 Wrms; f = 1 kHz 0.02 % Vripple = 200 mVPP PSRR Power Supply Rejection Ratio f = 217 Hz 85 f = 1 kHz 85 dB 73 CMRR Common-Mode Rejection Ratio f = 217 Hz, VCM = 200 mVPP 50 dB VOS Output Offset 4 mV VacINput = 0V Serial Interface Unless otherwise noted, VIN ( = VIN1 = VIN2 = BATT=VDD) = 3.6V, GND = 0V, CVIN1-2=10 F, CLDOX=1 F, and VLDO2 (DIGI) 1.8V. Typical values and limits appearing in normal type apply for TJ = 25C. Limits appearing in boldface type apply over the entire junction temperature range for operation, TA= TJ = -40C to +125C. (Notes 6, 7) Symbol Parameter Condition Typ Limit Min Max fCLK Clock Frequency tBF Bus-Free Time between START and STOP 1.3 s tHOLD Hold Time Repeated START Condition 0.6 s tCLK-LP CLK Low Period 1.3 s tCLK-HP CLK High Period 0.6 s tSU Set-Up Time Repeated START Condition 0.6 s tDATA-HOLD Data Hold Time 50 ns tDATA-SU Data Set-Up Time 100 ns tSU Set-Up Time for STOP Condition 0.6 s tTRANS Maximum Pulse Width of Spikes that Must be Suppressed by the Input Filter of both DATA & CLK Signals www.national.com 400 Units 50 12 kHz ns Note 2: All voltages are with respect to the potential at the GND pin. Note 3: Internal Thermal Shutdown circuitry protects the device from permanent damage. Note 4: The human-body model is 100 pF discharged through 1.5 k. The machine model is a 200 pF capacitor discharged directly into each pin, MIL-STD-883 3015.7. Note 5: Care must be exercised where high power dissipation is likely. The maximum ambient temperature may have to be derated. Like the Absolute Maximum power dissipation, the maximum power dissipation for operation depends on the ambient temperature. In applications where high power dissipation and/or poor thermal dissipation exists, the maximum ambient temperature may have to be derated. Maximum ambient temperature (TA_MAX) is dependent on the maximum power dissipation of the device in the application (PD_MAX), and the junction to ambient thermal resistance of the device/package in the application (JA), as given by the following equation: TA_MAX = TJ_MAX-OP - (JA X PDMAX ). Note 6: All limits are guaranteed. All electrical characteristics having room-temperature limits are tested during production with TJ = 25C. All hot and cold limits are guaranteed by correlating the electrical characteristics to process and temperature variations and applying statistical process control. Note 7: Guaranteed by design. Note 8: Dropout voltage is the input-to-output voltage difference at which the output voltage is 100 mV below its nominal value. This specification does not apply in cases it implies operation with an input voltage below the 3.0V minimum appearing under Operating Ratings. For example, this specification does not apply for devices having 1.5V outputs because the specification would imply operation with an input voltage at or about 1.5V. Note 9: Junction-to-ambient thermal resistance (JA) is taken from thermal modelling result, performed under the conditions and guidelines set forth in the JEDEC standard JESD51-7. The value of (JA) of this product could fall within a wide range, depending on PWB material, layout, and environmental conditions. In applications where high maximum power dissipation exists (high VIN, high IOUT), special care must be paid to thermal dissipation issues in board design. Note 10: Full-charge current is guaranteed for CHG_IN = 4.5 to 6.0V. At higher input voltages, increased power dissipation may cause the thermal regulation to limit the current to a safe level, resulting in longer charging time. 13 www.national.com LP3921 Note 1: Absolute Maximum Ratings are limits beyond which damage to the device may occur. Operating Ratings are conditions under which operation of the device is guaranteed. Operating Ratings do not imply guaranteed performance limits. For guaranteed performance limits and associated test conditions, see the Electrical Characteristics tables. LP3921 Technical Description DEVICE POWER UP AND SHUTDOWN TIMING 30069837 FIGURE 1. Device Power Up Logic Timing: PWR_ON www.national.com 14 LP3921 30069807 FIGURE 2. Device Power Up Logic Timing: CHG_IN, HF_PWR START UP Device start is initiated by any of the 3 input signals, PWR_ON, HF_PWR and CHG_IN. HF_PWR, CHGIN PS_HOLD needs to be asserted within 1200 ms after a CHG_IN or HF_PWR rising edge has been detected. For applications where a level sensitive input is required the LP3921 is available with a level detect input at HF_PWR. PWR_ON When PWR_ON goes high the device will remain powered up, a PS_HOLD applied will allow the device to remain powered after the PWR_ON signal has gone low. 15 www.national.com LP3921 30069808 FIGURE 3. LP3921 Power On Behavior (Failed PS_Hold) 30069833 FIGURE 4. LP3921 Normal Shutdown Behavior www.national.com 16 LP3921 LP3921 Serial Port Communication Slave Address Code 7h'7E TABLE 3. Control Registers Addr Register (default value) 8h'00 D7 D6 D5 D4 D3 D2 D1 D0 OP_EN (0000 0101) X X X X LDO7_EN LDO3_EN X LDO1_EN 8h'01 LDO1PGM O/P (0000 0001) X X X X V1_OP[3] V1_OP[2] V1_OP[1] V1_OP[0] 8h'02 LDO2PGM O/P (0000 1011) X X X X V2_OP[3] V2_OP[2] V2_OP[1] V2_OP[0] 8h'03 LDO3PGM O/P (0000 1011) X X X X V3_OP[3] V3_OP[2] V3_OP[1] V3_OP[0] 8h'04 LDO4PGM O/P (0000 1011) X X X X V4_OP[3] V4_OP[2] V4_OP[1] V4_OP[0] 8h'05 LDO5PGM O/P (0000 1011) X X X X V5_OP[3] V5_OP[2] V5_OP[1] V5_OP[0] 8h'06 LDO6PGM O/P (0000 1011) X X X X V6_OP[3] V6_OP[2] V6_OP[1] V6_OP[0] 8h'07 LDO7PGM O/P (0000 1011) X X X X V7_OP[3] V7_OP[2] V7_OP[1] V7_OP[0] 8h'0C STATUS (0000 0000) PWR_ON_ TRIB HF_PWR_ TRIG CHG_IN_ TRIG X X X X X 8h'10 CHGCNTL1 (0000 1001) USBMODE CHGMODE Force EOC _EN _EN TOUT_ doubling EN_Tout En_EOC X EN_CHG 8h'11 CHGCNTL2 (0000 0001) X X X Prog_ ICHG[4] Prog_ ICHG[3] Prog_ ICHG[2] Prog_ ICHG[1] Prog_ ICHG[0] 8h'12 CHGCNTL3 (0001 0010) X X VTERM[1] VTERM[0] Prog_ EOC[1] Prog_ EOC[0] Prog_ VRSTRT[1] Prog_ VRSTRT[0] 8h'13 CHGSTATUS1 Batt_Over_ Out CHGIN_ OK_Out EOC Tout_ Fullrate Tout_ Prechg LDO Mode Fullrate PRECHG 8h'14 CHGSTATUS2 X X X X X X Tout_ ConstV Bad_Batt 8h'19 Audio_Amp X X X X X X X amp_en APU_TSD_EN PS_HOLD _DELAY 8h'1C MISC Control1 X Bold X X X X X X Not Used Bits are Read Only type. Codes other than those shown in the table are disallowed. 17 www.national.com LP3921 The following table summarizes the supported output voltages for the LP3921. Default voltages after startup are highlighted in bold. TABLE 4. LDO Output Voltage Programming Data Code LDOx PGM O/P LDO1 (V) 8h'00 1.5 1.5 8h'01 1.8 1.8 1.8 8h'02 1.85 1.85 1.85 8h'03 2.5 2.5 2.5 2.5 8h'04 2.6 2.6 2.6 8h'05 2.7 2.7 2.7 2.7 2.7 2.7 2.7 8h'06 2.75 2.75 2.75 2.75 2.75 2.75 2.75 8h'07 2.8 2.8 2.8 2.8 2.8 2.8 2.8 8h'08 2.85 2.85 2.85 2.85 2.85 2.85 2.85 8h'09 2.9 2.9 2.9 2.9 2.9 2.9 2.9 8h'0A 2.95 2.95 2.95 2.95 2.95 2.95 2.95 8h'0B 3.0 3.0 3.0 3.0 3.0 3.0 3.0 8h'0C 3.05 3.05 3.05 3.05 3.05 3.05 3.05 8h'0D 3.1 3.1 3.1 3.1 8h'0E 3.2 3.2 3.2 3.2 8h'0F 3.3 3.3 3.3 3.3 LDO2 (V) VLDO3 (V) LDO4 (V) LDO5 (V) LDO6 (V) LDO7 (V) 1.5 2.6 The following table summarizes the supported charging current values for the LP3921. Default charge current after startup is 100 mA. TABLE 5. Charging Current Programming Prog_Ichg[4] Prog_Ichg[3 Prog_Ichg[2] Prog_Ichg[1] Prog_Ichg[0] I_Charge I mA 0 0 0 0 0 50 0 0 0 0 1 100 (Default) 0 0 0 1 0 150 0 0 0 1 1 200 0 0 1 0 0 250 0 0 1 0 1 300 0 0 1 1 0 350 0 0 1 1 1 400 0 1 0 0 0 450 0 1 0 0 1 500 0 1 0 1 0 550 0 1 0 1 1 600 0 1 1 0 0 650 0 1 1 0 1 700 0 1 1 1 0 750 0 1 1 1 1 800 1 0 0 0 0 850 1 0 0 0 1 900 1 0 0 1 0 950 www.national.com 18 LP3921 TABLE 6. Charging Termination Voltage Control VTERM[1] VTERM[0] Termination Voltage (V) 0 0 4.1 0 1 4.2 (Default) 1 0 4.3 1 1 4.4 TABLE 7. End Of Charge Current Control PROG_EOC[1] PROG_EOC[0] End of Charge Current 0 0 0.1 (Default) 0 1 0.15C 1 0 0.2C 1 1 0.25C Note: C is the set charge current. TABLE 8. Charging Restart Voltage Programming PROG_VRSTRT[1] PROG_VRSTRT[1] Restart Voltage(V) 0 0 VTERM - 50 mV 0 1 VTERM - 100 mV 1 0 VTERM - 150 mV 1 1 VTERM - 200 mV TABLE 9. USB Charging Selection USB_Mode_En CHG_Mode_En Mode Current 0 0 Fast Charge Default or Selection 1 0 Fast Charge Default or Selection 0 1 USB 100 mA 1 1 USB 450 mA nation voltage level. For start up the EOC function is disabled. This function should be enabled once start up is complete and a battery has been detected. EOC is enabled via register CHGCNTL1, Table 10. Battery Charge Management A charge management system allowing the safe charge and maintenance of a Li-Ion battery is implemented on the LP3921. This has a CC/CV linear charge capability with programmable battery regulation voltage and end of charge current threshold. The charge current in the constant current mode is programmable and a maintenance mode monitors for battery voltage drop to restart charging at a preset level. A USB charging mode is also available with 2 charge current levels. The full rate constant current rate of charge may be programmed to 19 levels from 50 mA to 950 mA. These values are given in Table 5 and Table 13. The charge mode may be programmed to USB mode when the charger input is applied and the battery voltage is above 3.0V. This provides two programmable current levels of 100 mA and 450 mA for a USB sourced supply input at CHG_IN. Table 9. CHARGER FUNCTION Following the correct detection of an input voltage at the charger pin the charger enters a pre-charge mode. In this mode a constant current of 50 mA is available to charge the battery to 3.0V. At this voltage level the charge management applies the default (100 mA) full rate constant current to raise the battery voltage to the termination voltage level (default 4.2V). The full rate charge current may be programmed to a different level at this stage. When termination voltage (VTERM) is reached, the charger is in constant voltage mode and a constant voltage of 4.2V is maintained. This mode is complete when the end of charge current (default 0.1C) is detected and the charge management enters the maintenance mode. In maintenance mode the battery voltage is monitored for the restart level (4.05V at the default settings) and the charge cycle is re-initiated to re-establish the termi- EOC EOC is disabled by default and should be enabled when the system processor is awake and the system detects that a battery is present. PROGRAMMING INFORMATION TABLE 10. Register Address 8h'10: CHGCNTL1 BIT NAME 2 En_EOC FUNCTION Enables the End Of Charge current level threshold detection. When set to '0' the EOC is disabled. The End Of Charge current threshold default setting is at 0.1C. This EOC value is set relative to C the set full rate con19 www.national.com LP3921 stant current. This threshold can be set to 0.1C, 0.15C, 0.2C or 0.25C by changing the contents of the PROG_EOC[1:0] register bits. CHARGER FULL RATE CURRENT Programming Information TABLE 13. Register Address 8h'11: CHGCNTL2 TABLE 11. Register Address 8h'12: CHGCNTL3 BIT NAME 2 Prog_EOC[0] 3 Prog_EOC[1] FUNCTION Data BITs HEX NAME FUNCTION Set the End Of Charge Current. See Table 7. 000[00000] 00 Prog_ICHG 50 mA 000[00001] 01 100 mA 000[00010] 02 150 mA 000[00011] 03 200 mA 000[00100] 04 250 mA 000[00101] 05 300 mA 000[00110] 06 350 mA 000[00111] 07 400 mA 000[01000] 08 450 mA 000[01001] 09 500 mA 000[01010] 0A 550 mA 000[01011] 0B 600 mA 000[01100] 0C 650 mA Set the charging termination voltage. See Table 6. 000[01101] 0D 700 mA 000[01110] 0E 750 mA 000[01111] 0F 800 mA Set the charging restart voltage. See Table 8. 000[10000] 10 850 mA 000[10001] 11 900 mA 000[10010] 12 950 mA TERMINATION AND RESTART The termination and restart voltage levels are determined by the data in the VTERM[1:0] and PROG_VSTRT[1:0] bits in the control register. The restart voltage is programmed relative to the selected termination voltage. The Termination voltages available are 4.1V, 4.2V (default), 4.3V, and 4.4V. The Restart voltages are determined relative to the termination voltage level and may be set to 50 mV, 100 mV, 150 mV (default), and 200 mV below the set termination voltage level. TABLE 12. Register Address 8h'12: CHGCNTL3 BIT NAME 4 VTERM[0] 5 VTERM[1] 0 VRSTR[0] 1 VRSTR[1] www.national.com FUNCTION 20 LP3921 30069836 FIGURE 5. Simplified Charger Functional State Diagram (EOC is enabled) The charger operation may be depicted by the following graphical representation of the voltage and current profiles. 21 www.national.com LP3921 30069835 FIGURE 6. Charge Cycle Diagram www.national.com 22 CHARGER CONTROL REGISTER 1 TABLE 14. Register Address 8h'10: CHGCNTL1 BIT NAME 7 USB_MODE _EN FUNCTION (if bit = '1') Sets the Current Level in USB mode. 6 CHG_MODE _EN Forces the charger into USB mode when active high. If low, charger is in normal charge mode. 5 FORCE _EOC Forces an EOC event. 4 TOUT_ Doubling Doubles the timeout delays for all timeout signals. 3 EN_Tout Enables the timeout counters. When set to '0' the timeout counters are disabled. 2 EN_EOC Enables the End of Charge current level threshold detection. When set to '0' the functions are disabled. 1 Set_ LDOmode Forces the charger into LDO mode. 0 EN_CHG Charger enable. 30069811 FIGURE 7. IMON Voltage vs. Charge Current Note that this function is not available if there is no input at CHG_IN or if the charger is off due to the input at CHG_IN being less than the compliance voltage. TABLE 15. Register Address 8h'13: CHGSTATUS1 BIT NAME 7 BAT_OVER _OUT FUNCTION (if bit = '1') 6 CHGIN_ OK_Out Is set when a valid input voltage is detected at CHG_IN pin. 5 EOC Is set when the charging current decreases below the programmed End Of Charge level. 4 Tout_ Fullrate 3 Tout_ Precharge Set after timeout for precharge mode. 2 LDO_Mode This bit is disabled in LP3921. Contact NSC sales if this option is required as in LP3918-L. 1 Fullrate Set when the charger is in CC/CV mode. 0 PRECHG LDO Information Is set when battery voltage exceeds 4.7V. OPERATIONAL INFORMATION The LP3921 has 7 LDO's of which 3 are enabled by default, LDO's 1,2 and 3 are powered up during the power up sequence. LDO's 4, 5 and 6 are separately, externally enabled and will follow LDO2 in start up if their respective enable pin is pulled high. LDO2, LDO3 and LDO7 can be enabled/disabled via the serial interface. LDO2 must remain in regulation otherwise the device will power down. While LDO1 is enabled this must also be in regulation for the device to remain powered. If LDO1 is disabled via I2C interface the device will not shut down. Set after timeout on full rate charge. INPUT VOLTAGES There are two input voltage pins used to power the 7 LDO's on the LP3921. VIN2is the supply for LDO3, LDO4, LDO5, LDO6 and LDO7. VIN1is the supply for LDO1 and LDO2. PROGRAMMING INFORMATION Set during precharge. Enable via Serial Interface Charger Status Register 2 Read only TABLE 17. Register Address 8h'00: OP_EN TABLE 16. Register Address 8h'13: CHGSTATUS2 BIT NAME 1 Tout_ConstV 0 BAD_BATT FUNCTION (if bit = '1') Set after timeout in CV phase. Set at bad battery state. BIT NAME 0 LDO1_EN 2 LDO3_EN 3 LDO7_EN FUNCTION Bit set to '0' - LDO disabled Bit set to '1' - LDO enabled Note that the default setting for this Register is [0000 0101]. This shows that LDO1 and LDO3 are enabled by default whereas LDO7 is not enabled by default on start up. 23 www.national.com LP3921 IMON CHARGE CURRENT MONITOR Charge current is monitored within the charger section and a proportional voltage representation of the charge current is presented at the IMON output pin. The output voltage relationship to the actual charge current is represented in the following graph and by the equation: VIMON(mV) = (2.47 x ICHG)(mA) Further Charger Register Information LP3921 It is also recommended that the output capacitor be placed within 1 cm from the output pin and returned to a clean ground line. TABLE 18. LDO Output Programming Register Add (hex) Name Data Range Output Voltage (hex) 01 LDO1PGM O/P 03 - 0F 1.5V to 3.3V (def. 1.8V) 02 LDO2PGM O/P 00 - 0F 2.5V to 3.3V (def 3.0V) 03 LDO3PGM O/P 05 - 0C 2.7V to 3.05V (def 3.0V) 04 LDO4PGM O/P 00 - 0F 1.5V to 3.3V (def 3.0V) 05 LDO5PGM O/P 05 - 0C 2.7V to 3.05V (def 3.0V) 06 LDO6PGM O/P 05 - 0C 2.7V to 3.05V (def 3.0V) 07 LDO7PGM O/P 00 - 0F 1.5V to 3.3V (def 3.0V) CAPACITOR CHARACTERISTICS The LDO's on the LP3921 are designed to work with ceramic capacitors on the input and output to take advantage of the benefits they offer. For capacitance values around 1 F, ceramic capacitors give the circuit designer the best design options in terms of low cost and minimal area. Generally speaking, input and output capacitors require careful understanding of the capacitor specification to ensure stable and correct device operation. Capacitance value can vary with DC bias conditions as well as temperature and frequency of operation. Capacitor values will also show some decrease over time due to aging. The capacitor parameters are also dependant on the particular case size with smaller sizes giving poorer performance figures in general. See Table 4 for full programmable range of values. EXTERNAL CAPACITORS The Low Drop Out Linear Voltage regulators on the LP3921 require external capacitors to ensure stable outputs. The LDO's on the LP3921 are specifically designed to use small surface mount ceramic capacitors which require minimum board space. These capacitors must be correctly selected for good performance INPUT CAPACITOR Input capacitors are required for correct operation. It is recommended that a 10 F capacitor be connected between each of the voltage input pins and ground (this capacitance value may be increased without limit). This capacitor must be located a distance of not more than 1 cm from the input pin and returned to a clean analogue ground. A ceramic capacitor is recommended although a good quality tantalum or film capacitor may be used at the input. 30069812 FIGURE 8. DC Bias (V) Warning: Important: Tantalum capacitors can suffer catastrophic failures due to surge current when connected to a low-impedance source of power (like a battery or a very large capacitor). If a tantalum capacitor is used at the input, it must be guaranteed by the manufacturer to have surge current rating sufficient for the application. There are no requirements for the ESR (Equivalent Series Resistance) on the input capacitor, but tolerance and temperature coefficient must be considered when selecting the capacitor to ensure the capacitance will remain within its operational range over the entire operating temperature range and conditions. As an example, Figure 8 shows a typical graph showing a comparison of capacitor case sizes in a Capacitance vs DC Bias plot. As shown in the graph, as a result of DC Bias condition the capacitance value may drop below minimum capacitance value given in the recommended capacitor table (0.7 F in this case). Note that the graph shows the capacitance out of spec for 0402 case size capacitor at higher bias voltages. It is therefore recommended that the capacitor manufacturers specifications for the nominal value capacitor are consulted for all conditions as some capacitor sizes (e.g., 0402) may not be suitable in the actual application. Ceramic capacitors have the lowest ESR values, thus making them best for eliminating high frequency noise. The ESR of a typical 1 F ceramic capacitor is in the range of 20 m to 40 m, and also meets the ESR requirements for stability. The temperature performance of ceramic capacitors varies by type. Capacitor type X7R is specified with a tolerance of 15% over temperature range -55C to +125C. The X5R has similar tolerance over the reduced temperature range -55C to +85C. Most large value ceramic capacitors (<2.2 F) are manufactured with Z5U or Y5V temperature characteristics, which results in the capacitance dropping by more than 50% as the temperature goes from 25C to 85C. Therefore X7R is recommended over these other capacitor types in applications OUTPUT CAPACITOR Correct selection of the output capacitor is critical to ensure stable operation in the intended application. The output capacitor must meet all the requirements specified in the recommended capacitor table over all conditions in the application. These conditions include DC-bias, frequency and temperature. Unstable operation will result if the capacitance drops below the minimum specified value. The LP3921 is designed specifically to work with very small ceramic output capacitors. The LDO's on the LP3921 are specifically designed to be used with X7R and X5R type capacitors. With these capacitors selection of the capacitor for the application is dependant on the range of operating conditions and temperature range for that application. (See section on Capacitor Characteristics). www.national.com 24 NO-LOAD STABILITY The LDO's on the LP3921 will remain stable in regulation with no external load. TABLE 19. LDO Output Capacitors Recommended Specification Symbol Parameter Capacitor Type Typ Co(LDO1) Capacitance X5R. X74 Co(LDO2) Capacitance X5R. X74 Co(LDO3) Capacitance Co(LDO4) Capacitance Co(LDO5) Co(LDO6) Co(LDO7) 1.0 0.7 2.2 F 1.0 0.7 2.2 F X5R. X74 1.0 0.7 2.2 F X5R. X74 1.0 0.7 2.2 F Capacitance X5R. X74 1.0 0.7 2.2 F Capacitance X5R. X74 1.0 0.7 2.2 F Capacitance X5R. X74 1.0 0.7 2.2 F MISC CONTROL REGISTER TABLE 21. Register Address 8h'1C: Misc. Bit The LP3921 has internal limiting for high on-chip temperatures caused by high power dissipation etc. This Thermal Shutdown, TSD, function monitors the temperature with respect to a threshold and results in a device power-down. If the threshold of +160C has been exceeded then the device will power down. Recovery from this TSD event can only be initiated after the chip has cooled below +115C. This device recovery is controlled by the APU_TSD_EN bit (bit 1) in control register MISC, 8h'1C. See Table 21. If the APU_TSD_EN is set low then the device will shutdown requiring a new start up event initiated by PWR_ON, HF_PWR, or CHG_IN. If APU_TSD_EN is set high then the device will power up automatically when the shutdown condition clears. In this case the control register settings are preserved for the device restart. The threshold temperature for the device to clear this TSD event is 115C. This threshold applies for any start up thus the device temperature must be below this threshold to allow a start up event to initiate power up. 0 PWR_HOLD_D 1b'0: If PWR_HOLD is low for 35 ms, ELAY the device will shutdown. (Default) 1b'1: If PWR_HOLD is low for 350 ms, the device will shut down. Differential Amplifier Explanation TABLE 22. Register Address 8h'19 Audio_Amp Bit 0 STATUS REGISTER READ ONLY Function (if bit = '1') 6 HF-PWR-TRIG PMU startup is initiated by PWR_TRIG. 5 CHG_IN_TRIG PMU startup is initiated by CHG_IN. Name amp_en Function (if the powerup default is "amplifier disabled") Bit set to '0' - amplifier disabled Bit set to '1' - amplifier enabled The LP3921 contains a fully differential audio amplifier that features differential input and output stages. Internally this is accomplished by two circuits: a differential amplifier and a common mode feedback amplifier that adjusts the output voltages so that the average value remains VDD/2. When setting the differential gain, the amplifier can be considered to have "halves". Each half uses an input and feedback resistor (Ri1 and RF1) to set its respective closed-loop gain. (See Figure 9.) With Ri1 = Ri2 and RF1 = RF2, the gain is set at -RF / Ri for each half. This results in a differential gain of: TABLE 20. Register Address 8h'0C: Status PWR_ON_TRI PMU startup is initiated by G PWR_ON. Function (if bit = '1') APU_TSD_EN 1b'0: Device will shut down completely if thermal shutdown occurs. Requires a new startup event to restart the PMU. 1b'1: Device will start up automatically after thermal shutdown condition is removed. (Device tries to keep its internal state.) Bits <7...2> are not used. Further Register Information 7 Name 1 Thermal Shutdown Name Units Max Note: The capacitor tolerance should be 30% or better over the full temperature range. X7R or X5R capacitors should be used. These specifications are given to ensure that the capacitance remains within these values over all conditions within the application. See Capacitor Characteristics section in Application Information. Bit Limit Min Bits <4...0> are not used. AVD = -RF/Ri (1) It is extremely important to match the input resistors to each other, as well as the feedback resistors to each other for best amplifier performance. A differential amplifier works in a manner where the difference between the two input signals is amplified. In most applications, this would require input sig25 www.national.com LP3921 where the temperature will change significantly above or below 25C. LP3921 nals that are 180 out of phase with each other. The LP3921 can be used, however, as a single ended input amplifier while still retaining its fully differential benefits. In fact, completely unrelated signals may be placed on the input pins. The LP3921 simply amplifies the difference between them. A bridged configuration, such as the one used in the LP3921, also creates a second advantage over single ended amplifiers. Since the differential outputs, Vo1 and Vo2, are biased at half-supply, no net DC voltage exists across the load. This assumes that the input resistor pair and the feedback resistor pair are properly matched. BTL configuration eliminates the output coupling capacitor required in single supply, singleended amplifier configurations. If an output coupling capacitor is not used in a single-ended output configuration, the halfsupply bias across the load would result in both increased internal IC power dissipation as well as permanent loudspeaker damage. Further advantages of bridged mode operation specific to fully differential amplifiers like the LP3921 include increased power supply rejection ratio, commonmode noise reduction, and click and pop reduction. 30069841 FIGURE 9. Audio Block in. to 0.013 in. Ensure efficient thermal conductivity by platingthrough and solder-filling the vias. Best thermal performance is achieved with the largest practical copper heat sink area. In all circumstances and conditions, the junction temperature must be held below 150C to prevent activating the LP3921's thermal shutdown protection. Further detailed and specific information concerning PCB layout, fabrication, and mounting an LLP package is available from National Semiconductor's package Engineering Group under application note AN1187. EXPOSED-DAP PACKAGE MOUNTING CONSIDERATIONS The LP3921's exposed-DAP (die attach paddle) package (LLP) provides a low thermal resistance between the die and the PCB to which the part is mounted and soldered. this allows rapid heat transfer from the die to the surrounding PCB copper traces, ground plane and, finally, surrounding air. Failing to optimize thermal design may compromise the LP3921's high-power performance and activate unwanted, though necessary, thermal shutdown protection. The LLP package must have its DAP soldered to a copper pad on the PCB> The DAP's PCB copper pad is connected to a large plane of continuous unbroken copper. This plane forms a thermal mass and heat sink and radiation area. Place the heat sink area on either outside plane in the case of a two-sided PCB, or on an inner layer of a board with more than two layers. Connect the DAP copper pad to the inner layer or backside copper heat sink area with a thermal via. The via diameter should be 0.012 www.national.com PCB LAYOUT AND SUPPLY REGULATION CONSIDERATIONS FOR DRIVING 4 LOADS Power dissipated by a load is a function of the voltage swing across the load and the load's impedance. As load impedance decreases, load dissipation becomes increasingly dependent on the interconnect (PCB trace and wire) resistance between the amplifier output pins and the load's connections. Residual trace resistance causes a voltage drop, which results in power 26 Poor power supply regulation adversely affects maximum output power. A poorly regulated supply's output voltage decreases with increasing load current. Reduced supply voltage causes decreased headroom, output signal clipping, and reduced output power. Even with tightly regulated supplies, trace resistance creates the same effects as poor supply regulation. Therefore, making the power supply traces as wide as possible helps maintain full output voltage swing. SHUTDOWN FUNCTION In order to reduce power consumption while not in use, the audio amplifier can be shut down by setting amp_en to 0 in the Audio_Amp register. On power-up, the audio amplifier is in shut down until enabled. (Contact NSC sales for a different option.) (See Table 22.) Thermal shutdown of the PMU will shut down the audio amplifier. (See Thermal Shutdown for recovery options.) Independent temperature sensing within the audio amplifier may also shut down the audio amplifier alone, without affecting PMU control logic. POWER DISSIPATION Power dissipation might be a major concern when designing a successful amplifier, whether the amplifier is bridged or single-ended. Equation 2 states the maximum power dissipation point for a single-ended amplifier operating at a given supply voltage and driving a specified output load. PDMAX = (VDD)2 / (22RL) Single-Ended (2) PROPER SELECTION OF EXTERNAL COMPONENTS Proper selection of external components in applications using integrated power amplifiers is critical when optimizing device and system performance. Although the LP3921 is tolerant to a variety of external component combinations, consideration of component values must be made when maximizing overall system quality. The LP3921 is unity-gain stable, giving the designer maximum system flexibility. The LP3921 should be used in low closed-loop gain configurations to minimize THD+N values and maximize signal to noise ratio. Low gain configurations require large input signals to obtain a given output power. Input signals equal to or greater than 1 Vrms are available from sources such as audio codecs. Please refer to the Audio Power Amplifier Design section for a more complete explanation of proper gain selection. When used in its typical application as a fully differential power amplifier the LP3921 does not require input coupling capacitors for input sources with DC common-mode voltages of less than VDD. Exact allowable input common-mode voltage levels are actually a function of VDD, Ri, and Rf and may be determined by Equation 5: However, a direct consequence of the increased power delivered to the load by a bridge amplifier is an increase in internal power dissipation versus a single-ended amplifier operating at the same conditions. PDMAX = 4 * (VDD)2 / (22RL) Bridge Mode (3) Since the LP3921 has bridged outputs, the maximum internal power dissipation is 4 times that of a single-ended amplifier. Even with this substantial increase in power dissipation, the LP3921 does not require additional heat sinking under most operating conditions and output loading. From Equation 3, assuming a 5V power supply and an 8 load, the maximum power dissipation contribution from the audio amplifier is 625 mW. To this must be added the power dissipated from the power management blocks. The maximum power dissipation thus obtained (PTOT) must not be greater than the power dissipation results from Equation 4: PTOT = PPDMU + PDMAX = (TJMAX - TA) / JA (4) PDPMU is mainly the sum of power dissipated in the charger and LDO blocks as shown in Equation 5: PDPMU = ICHG (VCHG_IN - VBATT) + (IOUT1 (VBATT - VOUT1) + (IOUT2 (VBATT - VOUT2) + (IOUT3 (VBATT - VOUT3) + ... (approx.) VCMi < (VDD-1.2)*((Rf+(Ri)/(Rf)-VDD*(Ri / 2Rf) (6) -RF / RI = AVD (7) (5) Special care must be taken to match the values of the feedback resistors (RF1 and RF2) to each other as well as matching the input resistors (Ri1 and Ri2) to each other (see Figure 9) more in front. Because of the balanced nature of differential amplifiers, resistor matching differences can result in net DC currents across the load. This DC current can increase power consumption, internal IC power dissipation, reduce PSRR, and possibly damaging the loudspeaker. Table 23 demonstrates this problem by showing the effects of differing values between the feedback resistors while assuming that the input resistors are perfectly matched. The results below apply to the application circuit shown in Figure 9, and assumes that The LP3921's JA in an SQA32A package is 30C/W. Depending on the ambient temperature, TA, of the system surroundings, Equation 4 can be used to find the maximum internal power dissipation supported by the IC packaging. POWER SUPPLY BYPASSING As with any power amplifier, proper supply bypassing is critical for low noise performance and high power supply rejection ratio (PSRR). The capacitor location on both the bypass and power supply pins should be as close to the device as 27 www.national.com LP3921 possible. A larger half-supply bypass capacitor improves PSRR because it increases half-supply stability. Typical applications employ a 5V regulator with 10 F and 0.1 F bypass capacitors that increase supply stability. This, however, does not eliminate the need for bypassing the supply nodes of the LP3921. The LP3921 will operate without the bypass capacitor CB, although the PSRR may decrease. A 1 F capacitor is recommended for CB. This value maximizes PSRR performance. Lesser values may be used, but PSRR decreases at frequencies below 1 kHz. The issue of CB selection is thus dependant upon desired PSRR and click and pop performance as explained in the section Proper Selection of External Components. dissipated in the trace and not in the load as desired. This problem of decreased load dissipation is exacerbated as load impedance decreases. Therefore, to maintain the highest load dissipation and widest output voltage swing, PCB traces that connect the output pins to a load must be as wide as possible. LP3921 VDD = 5V, RL = 8, and the system has DC coupled inputs tied to ground. supply voltage is (VOPEAK + (VDO TOP + (VDO BOT )), where VDO BOT and VDO TOP are extrapolated from the Dropout Voltage vs Supply Voltage curve in the Typical Performance Characteristics section. TABLE 23. Feedback Resistor Mis-match Tolerance RF1 RF2 V02 - V01 ILOAD 20% 1.2R -0.500V 62.5 mA 0.8R 10% 0.9R -0.250V 31.25 mA 5% 0.95R 1.05R -0.125V 1.1R 15.63 mA 1% 0.99R 1.01R -0.025V 3.125 mA 0% R 0 R 0 (8) Using the Output Power vs. Supply Voltage graph for an 8 load, the minimum supply rail just about 5V. Extra supply voltage creates headroom that allows the LP3921 to reproduce peaks in excess of 1W without producing audible distortion. At this time, the designer must make sure that the power supply choice along with the output impedance does not violate the conditions explained in the Power Dissipation section. Once the power dissipation equations have been addressed, the required differential gain can be determined from Equation 9. Similar results would occur if the input resistors were not carefully matched. Adding input coupling capacitors in between the signal source and the input resistors will eliminate this problem, however, to achieve best performance with minimum component count it is highly recommended that both the feedback and input resistors matched to 1% tolerance or better. (9) Rf / Ri = AVD AUDIO POWER AMPLIFIER DESIGN Design a 1W/8 Audio Amplifier Given: Power Output Load Impedance Input Level Input Impedance Bandwidth 1 Wrms 8 1 Vrms 20 k fH = 20 kHz * 5 = 100 kHz 100 Hz-20 kHz 0.25 dB (11) The high frequency pole is determined by the product of the desired frequency pole, fH , and the differential gain, AVD. With AVD = 2.83 and fH = 100 kHz, the resulting GBWP = 150 kHz which is much smaller than the LP3921 GBWP of 10 MHz. This figure displays that if a designer has a need to design an amplifier with a higher differential gain, the LP3921 can still be used without running into bandwidth limitations. A designer must first determine the minimum supply rail to obtain the specified output power. The supply rail can easily be found by extrapolating from the Output Power vs Supply Voltage graphs in the Typical Performance Characteristics section. A second way to determine the minimum supply rail is to calculate the required VOPEAK using Equation 8 and add the dropout voltages. Using this method, the minimum www.national.com (10) From Equation 10, the minimum AVD is 2.83. Since the desired input impedance was 20 k, a ratio of 2.83:1 of Rf to Ri results in an allocation of Ri = 20 k for both input resistors and Rf = 60 k for both feedback resistors. The final design step is to address the bandwidth requirement which must be stated as a single -3 dB frequency point. Five times away from a -3 dB point is 0.17 dB down from pass band response which is better than the required 0.25 dB specified. 28 INTERFACE BUS OVERVIEW The I2C compatible synchronous serial interface provides access to the programmable functions and registers on the device. This protocol uses a two-wire interface for bi-directional communications between the IC's connected to the bus. The two interface lines are the Serial Data Line (SDA), and the Serial Clock Line (SCL). These lines should be connected to a positive supply, via a pull-up resistor of 1.5 k, and remain HIGH even when the bus is idle. Every device on the bus is assigned a unique address and acts as either a Master or a Slave depending on whether it generates or receives the serial clock (SCL). START AND STOP The Master device on the bus always generates the Start and Stop Conditions (control codes). After a Start Condition is generated, the bus is considered busy and it retains this status until a certain time after a Stop Condition is generated. A high-to-low transition of the data line (SDA) while the clock (SCL) is high indicates a Start Condition. A low-to-high transition of the SDA line while the SCL is high indicates a Stop Condition. DATA TRANSACTIONS One data bit is transferred during each clock pulse. Data is sampled during the high state of the serial clock (SCL). Consequently, throughout the clock's high period, the data should remain stable. Any changes on the SDA line during the high state of the SCL and in the middle of a transaction, aborts the current transaction. New data should be sent during the low SCL state. This protocol permits a single data line to transfer both command/control information and data using the synchronous serial clock. 30069810 FIGURE 11. Start and Stop Conditions In addition to the first Start Condition, a repeated Start Condition can be generated in the middle of a transaction. This allows another device to be accessed, or a register read cycle. ACKNOWLEDGE CYCLE The Acknowledge Cycle consists of two signals: the acknowledge clock pulse the master sends with each byte transferred, and the acknowledge signal sent by the receiving device. The master generates the acknowledge clock pulse on the ninth clock pulse of the byte transfer. The transmitter releases the SDA line (permits it to go high) to allow the receiver to send the acknowledge signal. The receiver must pull down the SDA line during the acknowledge clock pulse and ensure that SDA remains low during the high period of the clock pulse, thus signaling the correct reception of the last data byte and its readiness to receive the next byte. 30069813 FIGURE 10. Bit Transfer Each data transaction is composed of a Start Condition, a number of byte transfers (set by the software) and a Stop 30069828 FIGURE 12. Bus Acknowledge Cycle 29 www.national.com LP3921 Condition to terminate the transaction. Every byte written to the SDA bus must be 8 bits long and is transferred with the most significant bit first. After each byte, an Acknowledge signal must follow. The following sections provide further details of this process. I2C Compatible Serial Bus Interface LP3921 "ACKNOWLEDGE AFTER EVERY BYTE" RULE The master generates an acknowledge clock pulse after each byte transfer. The receiver sends an acknowledge signal after every byte received. There is one exception to the "acknowledge after every byte" rule. When the master is the receiver, it must indicate to the transmitter an end of data by not-acknowledging ("negative acknowledge") the last byte clocked out of the slave. This "negative acknowledge" still includes the acknowledge clock pulse (generated by the master), but the SDA line is not pulled down. CONTROL REGISTER READ CYCLE * Master device generates a start condition. * Master device sends slave address (7 bits) and the data direction bit (R/W = "0"). * Slave device sends acknowledge signal if the slave address is correct. * Master sends control register address (8 bits). * Slave sends acknowledge signal. * Master device generates repeated start condition. * Master sends the slave address (7 bits) and the data direction bit (R/W = "1"). * Slave sends acknowledge signal if the slave address is correct. * Slave sends data byte from addressed register. * If the master device sends acknowledge signal, the control register address will be incremented by one. Slave device sends data byte from addressed register. * Read cycle ends when the master does not generate acknowledge signal after data byte and generates stop condition. ADDRESSING TRANSFER FORMATS Each device on the bus has a unique slave address. The LP3921 operates as a slave device with the address 7h'7E (binary 1111110). Before any data is transmitted, the master transmits the address of the slave being addressed. The slave device should send an acknowledge signal on the SDA line, once it recognizes its address. The slave address is the first seven bits after a Start Condition. The direction of the data transfer (R/W) depends on the bit sent after the slave address -- the eighth bit. When the slave address is sent, each device in the system compares this slave address with its own. If there is a match, the device considers itself addressed and sends an acknowledge signal. Depending upon the state of the R/W bit (1:read, 0:write), the device acts as a transmitter or a receiver. TABLE 24. I2C Read/Write Sequences Address Mode CONTROL REGISTER WRITE CYCLE * Master device generates start condition. * Master device sends slave address (7 bits) and the data direction bit (R/W = "0"). * Slave device sends acknowledge signal if the slave address is correct. * Master sends control register address (8 bits). * Slave sends acknowledge signal. * Master sends data byte to be written to the addressed register. * Slave sends acknowledge signal. * If master will send further data bytes the control register address will be incremented by one after acknowledge signal. * Write cycle ends when the master creates stop condition. Data Read [Ack] [Ack] [Ack] [Register Date] ... additional reads from subsequent register address possible Data Write [Ack] [Ack] [Ack] ... additional writes to subsequent register address possible < > Data from master [ ] Data from slave REGISTER READ AND WRITE DETAIL 30069829 FIGURE 13. Register Write Format www.national.com 30 LP3921 30069830 FIGURE 14. Register Read Format 31 www.national.com LP3921 Physical Dimensions inches (millimeters) unless otherwise noted 32-pin LLP Package NS Package Number MKT-SQA32A www.national.com 32 LP3921 Notes 33 www.national.com LP3921 Battery Charger Management and Regulator Unit with Integrated Boomer Audio Amplifier Notes For more National Semiconductor product information and proven design tools, visit the following Web sites at: Products Design Support Amplifiers www.national.com/amplifiers WEBENCH www.national.com/webench Audio www.national.com/audio Analog University www.national.com/AU Clock Conditioners www.national.com/timing App Notes www.national.com/appnotes Data Converters www.national.com/adc Distributors www.national.com/contacts Displays www.national.com/displays Green Compliance www.national.com/quality/green Ethernet www.national.com/ethernet Packaging www.national.com/packaging Interface www.national.com/interface Quality and Reliability www.national.com/quality LVDS www.national.com/lvds Reference Designs www.national.com/refdesigns Power Management www.national.com/power Feedback www.national.com/feedback Switching Regulators www.national.com/switchers LDOs www.national.com/ldo LED Lighting www.national.com/led PowerWise www.national.com/powerwise Serial Digital Interface (SDI) www.national.com/sdi Temperature Sensors www.national.com/tempsensors Wireless (PLL/VCO) www.national.com/wireless THE CONTENTS OF THIS DOCUMENT ARE PROVIDED IN CONNECTION WITH NATIONAL SEMICONDUCTOR CORPORATION ("NATIONAL") PRODUCTS. NATIONAL MAKES NO REPRESENTATIONS OR WARRANTIES WITH RESPECT TO THE ACCURACY OR COMPLETENESS OF THE CONTENTS OF THIS PUBLICATION AND RESERVES THE RIGHT TO MAKE CHANGES TO SPECIFICATIONS AND PRODUCT DESCRIPTIONS AT ANY TIME WITHOUT NOTICE. NO LICENSE, WHETHER EXPRESS, IMPLIED, ARISING BY ESTOPPEL OR OTHERWISE, TO ANY INTELLECTUAL PROPERTY RIGHTS IS GRANTED BY THIS DOCUMENT. TESTING AND OTHER QUALITY CONTROLS ARE USED TO THE EXTENT NATIONAL DEEMS NECESSARY TO SUPPORT NATIONAL'S PRODUCT WARRANTY. EXCEPT WHERE MANDATED BY GOVERNMENT REQUIREMENTS, TESTING OF ALL PARAMETERS OF EACH PRODUCT IS NOT NECESSARILY PERFORMED. NATIONAL ASSUMES NO LIABILITY FOR APPLICATIONS ASSISTANCE OR BUYER PRODUCT DESIGN. BUYERS ARE RESPONSIBLE FOR THEIR PRODUCTS AND APPLICATIONS USING NATIONAL COMPONENTS. PRIOR TO USING OR DISTRIBUTING ANY PRODUCTS THAT INCLUDE NATIONAL COMPONENTS, BUYERS SHOULD PROVIDE ADEQUATE DESIGN, TESTING AND OPERATING SAFEGUARDS. EXCEPT AS PROVIDED IN NATIONAL'S TERMS AND CONDITIONS OF SALE FOR SUCH PRODUCTS, NATIONAL ASSUMES NO LIABILITY WHATSOEVER, AND NATIONAL DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY RELATING TO THE SALE AND/OR USE OF NATIONAL PRODUCTS INCLUDING LIABILITY OR WARRANTIES RELATING TO FITNESS FOR A PARTICULAR PURPOSE, MERCHANTABILITY, OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. LIFE SUPPORT POLICY NATIONAL'S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS PRIOR WRITTEN APPROVAL OF THE CHIEF EXECUTIVE OFFICER AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: Life support devices or systems are devices which (a) are intended for surgical implant into the body, or (b) support or sustain life and whose failure to perform when properly used in accordance with instructions for use provided in the labeling can be reasonably expected to result in a significant injury to the user. A critical component is any component in a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system or to affect its safety or effectiveness. National Semiconductor and the National Semiconductor logo are registered trademarks of National Semiconductor Corporation. All other brand or product names may be trademarks or registered trademarks of their respective holders. Copyright(c) 2008 National Semiconductor Corporation For the most current product information visit us at www.national.com National Semiconductor Americas Technical Support Center Email: support@nsc.com Tel: 1-800-272-9959 www.national.com National Semiconductor Europe Technical Support Center Email: europe.support@nsc.com German Tel: +49 (0) 180 5010 771 English Tel: +44 (0) 870 850 4288 National Semiconductor Asia Pacific Technical Support Center Email: ap.support@nsc.com National Semiconductor Japan Technical Support Center Email: jpn.feedback@nsc.com IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI's standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Audio www.ti.com/audio Communications and Telecom www.ti.com/communications Amplifiers amplifier.ti.com Computers and Peripherals www.ti.com/computers Data Converters dataconverter.ti.com Consumer Electronics www.ti.com/consumer-apps DLP(R) Products www.dlp.com Energy and Lighting www.ti.com/energy DSP dsp.ti.com Industrial www.ti.com/industrial Clocks and Timers www.ti.com/clocks Medical www.ti.com/medical Interface interface.ti.com Security www.ti.com/security Logic logic.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Power Mgmt power.ti.com Transportation and Automotive www.ti.com/automotive Microcontrollers microcontroller.ti.com Video and Imaging RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap Wireless Connectivity www.ti.com/wirelessconnectivity TI E2E Community Home Page www.ti.com/video e2e.ti.com Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2011, Texas Instruments Incorporated