DNT24PA - MURATA MANUFACTURING - Datasheet.Directory

DNT24CA

DNT24PA

Rating Value Units

Power Supply Input -0.5 to +6.5 V

All Input/Output Pins -0.5 to +3.3 V

Input Power to RFIO Port 0 dBm

Non-Operating Ambient Temperature Range -40 to +85 oC

DNT24CA/PA Absolute Maximum Ratings

DNT24CA/PA Electrical Characteristics

Characteristic Sym Notes Minimum Typical Maximum Units

Operating Frequency Range 2406 2475 MHz

Hop Duration 1 8 100 ms

Number of RF Channels 1 15 or 24

Modulation FSK

RF Data Transmission Rate 250 kbps

Receiver Sensitivity @ 10-5 BER -100 dBm

Transmitter RF Output Power 1 10 or 63 mW

Antenna Dielectric Chip Antenna

System Topologies Point-to-Point, Point-to-Multipoint,

Peer-to-Peer and Store & Forward

Access Scheme Ad Hoc TDMA

Low Cost

2.4 GHz FHSS

Transceiver

Modules with

I/O

The DNT24CA and DNT24PA FHSS transceiver modules provide a low-cost, versatile solu-

tion for wireless data communications in the 2.4 GHz ISM band. The RF output power can be

set at 10 or 63 mW. The modules include analog, digital and serial I/O, providing the flexibility

to serve applications ranging from cable replacements to sensor networks. The built-in chip

antenna makes these modules very easy to integrate.

- 2.4 GHz Frequency Hopping Spread Spectrum Transceiver

- Point-to-point, Point-to-multipoint, Peer-to-peer and

Store & Forward Capabilities

- Transmitter RF Power Configurable - 10 or 63 mW

- Built-in Chip Antenna

- 250 kbps RF Data Rate

- Serial Port Data Rate up to 250 kbps, SPI Port Data Rate up to 500 kbps

- 128-Bit AES Encryption

- Separate Serial Port for Diagnostics

- Analog and Digital I/O for Sensor Applications

- FCC, Canadian IC and ETSI Certified for Unlicensed Operation

DNT24CA/PA 10/04/16

1 of 7

www.murata.com

Notes:

1. The DNT24CA and DNT24PA achieve regulatory certification under FHSS rules.

2. Maximum sleep current occurs at +85 oC.

Characteristic Sym Notes Minimum Typical Maximum Units

ADC Input Range 0 2.7 V

ADC Input Resolution 12 bits

ADC Sample Rate 100 Hz

Signal Source Impedance for ADC Reading 10 KΩ

ADC External Reference Voltage Range 1.0 2.7 V

DAC Output Range 0 3.3 V

DAC Output Resolution 12 bits

Primary and Diagnostic Serial Port Baud Rates 1.2, 2.4, 4.8, 9.6, 14.4, 19.2, 28.8,

38.4, 57.6, 115.2, 230.4, 250.0 kbps

Serial Peripheral Interface Data Rate 125 500 kbps

Digital I/O:

Logic Low Input Level -0.5 0.8 V

Logic High Input Level 2.45 3.3 V

Logic Input Internal Pull-up Resistor 20 KΩ

Power Supply Voltage Range VCC +3.3 +5.5 Vdc

Power Supply Voltage Ripple 10 mVP-P

Peak Transmit Mode Current, 63 mW Output 140 mA

Average Operating Receive Current:

Base and Remote, Continuous Data Stream 55 mA

Remote, Linked, No Data Transmission 15 mA

Sleep Current 2 3 6 µA

DNT24CA Mounting Reflow Soldering

DNT24PA Mounting Socket

Operating Temperature Range -40 85 oC

Operating Relative Humidity Range, Non-condensing 10 90 %

DNT24CA/PA Electrical Characteristics

CAUTION: Electrostatic Sensitive Device. Observe precautions when handling.

DNT24CA/PA 10/04/16

2 of 7

www.murata.com

DNT24CA/PA Hardware

The major components of these modules include a

2.4 GHz FHSS transceiver and a low current 8-bit

microcontroller. These modules operate in the 2.4

GHz ISM band. There are 12 selectable hopping pat-

terns providing compatibility with frequency allocations

in most regions of the world. The modules also have

two selectable RF output power levels: 10 mW and

63 mW.

The DNT24CA/PA provide a variety of hardware inter-

faces. There are two serial ports plus one SPI port. Ei-

ther the primary serial port or the SPI port can be

selected for data communications. The second serial

port is dedicated to diagnostics. The primary and diag-

nostic serial ports support most standard baud rates

up to 250.0 kbps. The SPI port supports data rates up

to 500 kbps. These modules also include three ADC

inputs, two DAC outputs, and six general-purpose digi-

tal I/O ports. Four of the digital I/O ports support an

optional interrupt-from-sleep mode when configured

as inputs. The DNT24CA is designed for solder reflow

mounting. The DNT24PA is designed for plug-in con-

nector mounting.

DNT24CA/PA Firmware

DNT24CA/PA firmware operates using hybrid Ad Hoc

TDMA channel access optimized for periodic burst

transmissions. DNT24CA/PA firmware operates “out

of the box” using point-to-point transparent serial

mode, with point-to-multipoint, peer-to-peer and store

& forward system topologies also supported.

The firmware provides the user with a rich set of con-

figuration options including a choice of hopping pat-

terns, hopping dwell times, serial and/or SPI data port

operation, serial and SPI data rate selection, RF out-

put power selection, plus configurable analog and digi-

tal I/O lines.

Data integrity is protected by 24-bit error detection,

with optional ACK and automatic transmission retries

or redundant transmissions. 128-bit AES encryption

provides a high level of data security for sensitive

applications. Sensor networks can take advantage of

timer or event-based data reporting and remote node

sleep cycling for extended battery life.

1 8 1 9 2 0 2 1 2 2 2 311 2 2 5 2

1 5

1 3

1 2

1 1

1 0

T 2 C A / T 2 P A B l o c k i a g r a m

M i c r o c o n r o l l e r

R e g

A C T ( I A G _ T X )

/ C ( I A G _ R X )

G P I O 0

R A I O _ T X

R A I O _ R X

G P I O ( / H O S T _ C T S )

G P I O 5 ( / H O S T _ R T S )

A C 0

G P I O 2

G P I O 1

G P I O 3 ( A V )

A C 1

V C C

/ R E S E T

A C 1

M I S O

M O S I

/ S S

S C L K

3 . 3 V _ O U T

A C _ E X T _ R E F

A C 0

+ 3 . 3 V

2 8 2 9 3 0

R S V

2 . G H z

T r a n s c e i v e r

I R Q 0

I R Q 1 / C L K

A T A

P L L _ L O C K

S C K

S I

S O

n S S _ A T A

n S S _ C O F I G

R S V

R F I O

T / R

P W R

P R E

F i l e r

C h i p

A n e n n a

Figure 1

DNT24CA/PA 10/04/16

3 of 7

www.murata.com

Pin Name I/O Description

1GND - Power supply and signal ground. Connect to the host circuit board ground.

2ACT

(DIAG_TX)

(O)

This pin’s default configuration is data activity output. On a base, this signal blinks when a valid packet is

received. On a remote, this signal blinks when a packet is transmitted. On a router, this signal blinks when

a valid upstream packet is received or a downstream packet is transmitted. Alternate pin function is the di-

agnostic serial port output.

3/DCD

(DIAG_RX)

(I)

This pin’s default configuration is data carrier detect output. On a base, this signal is asserted when any

valid packet is received, and is cleared if no packets are heard for the configured router/remote registra-

tion time-out interval. On a router or remote, this signal is asserted when the radio obtains hopping pattern

synchronization, and remains asserted until no beacons are heard for 50 hops. Alternate pin function is

the diagnostic serial port input.

4GPIO0 I/O

Configurable digital I/O port 0. When configured as an input, an internal pull-up resistor can be selected

and direct interrupt from sleep can be invoked. When configured as an output, the power-on state is

configurable. In sleep mode the pin direction, input pull-up selection or output state are also separately

configurable.

5 RADIO_TXD O Serial data output from the radio.

6RADIO_RXD I Serial data input to the radio.

7GPOI4

(/HOST_CTS)

I/O

(O)

Default pin function is GPIO4 with the same configuration options as GPIO0. Alternate pin function is

UART/SPI flow control output. The module sets this line low when it is ready to accept data from the host

on the RADIO_RXD or MOSI input. When the line goes high, the host must stop sending data.

8GPOI5

(/HOST_RTS)

I/O

(I)

Default pin function is GPIO5 with the same configuration options as GPIO0. Alternate pin function is

UART/SPI flow control input. The host sets this line low to allow data to flow from the module on

the RADIO_TXD pin. When the host sets this line high, the module will stop sending data to the host.

9DAC0 O 12-bit DAC 0 output. Full scale output can be referenced to the voltage at pin 25 or the 3.3 V regulated

module bus voltage.

10 GPIO2 I/O Configurable digital I/O port 2. Same configuration options as GPIO0.

11 GPIO1 I/O Configurable digital I/O port 1. Same configuration options as GPIO0.

12 GPIO3

(DAV)

I/O

(O)

Default pin function is GPIO3 with the same configuration options as GPIO0. When SPI slave mode oper-

ation is enabled, a logic high on this pin indicates when data is available to be clocked out by the SPI

master.

13 DAC1 O 12-bit DAC 1 output. Same specifications and configuration options as DAC0.

14 VCC I Power supply input, +3.3 to +5.5 Vdc.

15 GND -Power supply and signal ground. Connect to the host circuit board ground.

16 GND -Power supply and signal ground. Connect to the host circuit board ground.

17 /RESET I Active low module hardware reset.

18 ADC0 I

ADC input 0. This pin is a direct ADC input when the ADC is operating in single-ended mode, or the differ-

ential negative input for positive inputs applied to ADC1 or ADC2 when the ADC is operating in differential

mode. Full-scale reading can be referenced to Pin 25 for ratiometric measurements. For absolute mea-

surements, the ADC can use either the regulated supply voltage divided by 1.6 (about 2.06 V), or an ex-

ternal voltage applied to Pin 25. In single-ended mode, ADC measurements are 11-bit unsigned values

with full scale nominally 2.7 V when referenced to a 2.7 V input on Pin 27. In differential mode, ADC mea-

surements are 12-bit signed values.

19 ADC1 IADC input 1. Direct input when the ADC is operating in single-ended mode, positive differential input rela-

tive to ADC0 when the ADC is operating in differential mode.

20 MISO I/O This pin is the SPI master mode input or slave mode output.

21 MOSI I/O This pin is the SPI master mode output or slave mode input.

22 /SS I/O SPI active low slave select. This pin is an output when the module is operating as a master, and an input

when it is operating as a slave.

DNT24CA/PA I/O Descriptions

DNT24CA/PA 10/04/16

4 of 7

www.murata.com

Pin Name I/O Description

23 SCLK I/O SPI clock signal. This pin is an output when operating as a master, and an input when operating as

a slave.

24 ADC2 IADC input 2. Direct input when the ADC is operating in single-ended mode, positive differential input rela-

tive to ADC0 when the ADC is operating in differential mode.

25 ADC_EXT_

REF I/O

ADC external reference voltage pin. The voltage at this pin can be used by the ADCs as a reference for

ratiometric measurements. With no external voltage or load applied, this pin presents a nominal 2.7 V out-

put through a 2.126 K source resistance. A low impedance external reference voltage in the range of 1 to

2.7 V may be applied to this pin as an option.

26 RSVD -Reserved pin. Leave unconnected.

27 RSVD -Reserved pin. Leave unconnected.

28 GND -Connect to the host circuit board ground plane.

29 RSVD -Reserved pin. Leave unconnected.

30 GND - Connect to the host circuit board ground plane.

DNT24CA/PA 10/04/16

5 of 7

www.murata.com

1 . 5 0 0

( 3 8 . 1 0 )

0 . 9 8 0

( 2 . 9 0 )

T 2 C A O u l i n e a n d M o u n i n g i m e n s i o n s

0 . 0 5 0 ( 1 . 2 )

T o p V i e w

0 . 1 2 5

( 3 . 1 8 )

1 5

13 0

i m e n s i o n s i n i n c h e s ( m m )

0 . 4 5 0 ( 1 1 . 4 0 ) 0 . 3 5 0 ( 8 . 8 9 )

A n e n n a

Figure 2

0 . 0 0 ( 1 . 5 2 )

1 . 5 0 0 ( 3 8 . 1 0 )

0 . 9 8 0

( 2 . 9 0 )

T 2 C A S o l d e r P a d i m e n s i o n s

0 . 0 5 0 ( 1 . 2 )

T o p V i e w

1 5

1 3 0

i m e n s i o n s i n i n c h e s ( m m )

0 . 0 3 5 ( 0 . 8 9 )

1 . 0 0

( 2 . 2 )

Figure 3

DNT24CA/PA 10/04/16

6 of 7

www.murata.com

0.980

( 2 . 9 )

0.050

( 1 . 2 )

0 . 0 0

( 1 . 8 )

0.100

( 2 . 5 )

0.800

( 2 0 . 3 )

T 2 P A I n e r f a c e C o n n e c o r

P C B L a y o u e a i l

C o n n e c o r s a r e S A M T E C

S L M - 1 1 5 - 0 1 - G - S

o r E q u i v a l e n

i m e n s i o n s a r e i n i n c h e s ( m m )

Figure 5

Note: Specifications subject to change without notice.

Part # M-0024-0000, Rev C

0 . 0 0

( 1 . 5 2 )

1 . 5 0 0

( 3 8 . 1 0 )

1 . 1 0 0

( 2 . 9 )

T 2 P A O u l i n e a n d M o u n i n g i m e n s i o n s

0 . 0 5 0 ( 1 . 2 )

T o p V i e w

0 . 1 2 5

( 3 . 1 8 )

1 5

1 3 0

i m e n s i o n s i n i n c h e s ( m m )

0 . 5 0 ( 1 1 . 3 )

0 . 2 2 5

( 5 . 2 )

0 . 9 8 0

( 2 . 9 0 )

0 . 3 5 0 ( 8 . 8 9 )

A n e n n a

Figure 4

DNT24CA/PA 10/04/16

7 of 7