Transient Voltage Suppression Diodes Surface Mount - 3000W > SMDJ-HR series SMDJ-HR Series RoHS Description Uni-directional TVS Diode Arrays (SPATM Family of Products) The SMDJ-HR High Reliability series is designed specifically to protect sensitive electronic equipment from voltage transients induced by lightning and other transient voltage events. Bi-directional Features * For surface mounted applications in order to optimize board space * Low profile package * Built-in strain relief * VBR @TJ= VBR@25C x (1+T Agency Approvals AGENCY x (TJ - 25)) AGENCY FILE NUMBER (T:Temperature Coefficient) E230531 Symbol Value Unit Peak Pulse Power Dissipation at TA=25C by 10/1000s waveform (Fig.1)(Note 1), (Note 2) PPPM 3000 W Power Dissipation on infinite heat sink at TA=50OC PM(AV) 6.5 W * Glass passivated chip junction * 3000W peak pulse power capability at 10/1000s waveform, repetition rate (duty cycles):0.01% * Fast response time: typically less than 1.0ps from 0V to BV min * Excellent clamping capability Peak Forward Surge Current, 8.3ms Single Half Sine Wave (Note 3) IFSM 300 A Applications Maximum Instantaneous Forward Voltage at 100A for Unidirectional only VF 3.5 V TJ , TSTG -55 to 150 C Typical Thermal Resistance Junction to Lead RuJL 15 C/W Typical Thermal Resistance Junction to Ambient RuJA 75 C/W Maximum Ratings and Thermal Characteristics (TA=25OC unless otherwise noted) Parameter Operating Junction and Storage Temperature Range * Low incremental surge resistance * Typical IR less than 2A above 12V * High temperature soldering guaranteed: 260C/40 seconds at terminals * Plastic package has underwriters laboratory flammability 94V-O * Meet MSL level1, per J-STD-020, LF maximun peak of 260C * Matte tin lead-free plated * Halogen free and RoHS compliant TVS devices are ideal for the protection of I/O Interfaces, VCC bus and other vulnerable circuits used in Telecom, Computer, Industrial and Consumer electronic applications. Notes: 1. Non-repetitive current pulse , per Fig. 3 and derated above TA = 25OC per Fig. 2. 2. Mounted on copper pad area of 0.31x0.31" (8.0 x 8.0mm) to each terminal. 3. Measured on 8.3ms single half sine wave or equivalent square wave for unidirectional device only, duty cycle=4 per minute maximum. Functional Diagram Bi-directional Cathode Anode Uni-directional SMDJ-HR Series 1 55 (c)2013 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 11/18/13 Transient Voltage Suppression Diodes Surface Mount - 3000W > SMDJ-HR series Electrical Characteristics Maximum Reverse Breakdown TM TVSMarking Diode Arrays Family Test of Products) Stand off (SPA Voltage V Current Clamping Part Number (Uni) Part Number (Bi) SMDJ5.0A-HR SMDJ6.0A-HR SMDJ6.5A-HR SMDJ7.0A-HR SMDJ7.5A-HR SMDJ8.0A-HR SMDJ8.5A-HR SMDJ9.0A-HR SMDJ10A-HR SMDJ11A-HR SMDJ12A-HR SMDJ13A-HR SMDJ14A-HR SMDJ15A-HR SMDJ16A-HR SMDJ17A-HR SMDJ18A-HR SMDJ20A-HR SMDJ22A-HR SMDJ24A-HR SMDJ26A-HR SMDJ28A-HR SMDJ30A-HR SMDJ33A-HR SMDJ36A-HR SMDJ40A-HR SMDJ43A-HR SMDJ45A-HR SMDJ48A-HR SMDJ51A-HR SMDJ54A-HR SMDJ58A-HR SMDJ60A-HR SMDJ64A-HR SMDJ70A-HR SMDJ75A-HR SMDJ78A-HR SMDJ85A-HR SMDJ90A-HR SMDJ100A-HR SMDJ110A-HR SMDJ120A-HR SMDJ130A-HR SMDJ5.0CA-HR SMDJ6.0CA-HR SMDJ6.5CA-HR SMDJ7.0CA-HR SMDJ7.5CA-HR SMDJ8.0CA-HR SMDJ8.5CA-HR SMDJ9.0CA-HR SMDJ10CA-HR SMDJ11CA-HR SMDJ12CA-HR SMDJ13CA-HR SMDJ14CA-HR SMDJ15CA-HR SMDJ16CA-HR SMDJ17CA-HR SMDJ18CA-HR SMDJ20CA-HR SMDJ22CA-HR SMDJ24CA-HR SMDJ26CA-HR SMDJ28CA-HR SMDJ30CA-HR SMDJ33CA-HR SMDJ36CA-HR SMDJ40CA-HR SMDJ43CA-HR SMDJ45CA-HR SMDJ48CA-HR SMDJ51CA-HR SMDJ54CA-HR SMDJ58CA-HR SMDJ60CA-HR SMDJ64CA-HR SMDJ70CA-HR SMDJ75CA-HR SMDJ78CA-HR SMDJ85CA-HR SMDJ90CA-HR SMDJ100CA-HR SMDJ110CA-HR SMDJ120CA-HR SMDJ130CA-HR UNI BI Voltage VR (Volts) RDE RDG RDK PDM PDP PDR PDT PDV PDX PDZ PEE PEG PEK PEM PEP PER PET PEV PEX PEZ PFE PFG PFK PFM PFP PFR PFT PFV PFX PFZ RGE PGG PGK PGM PGP PGR PGT PGV PGX PGZ PHE PHG PHK DDE DDG DDK DDM DDP DDR DDT DDV DDX DDZ DEE DEG DEK DEM DEP DER DET DEV DEX DEZ DFE DFG DFK DFM DFP DFR DFT FVH FXH FZH GEH GGH GKH GMH GPH GRH GTH GVH GXH GZH HEH HGH HKH 5.0 6.0 6.5 7.0 7.5 8.0 8.5 9.0 10.0 11.0 12.0 13.0 14.0 15.0 16.0 17.0 18.0 20.0 22.0 24.0 26.0 28.0 30.0 33.0 36.0 40.0 43.0 45.0 48.0 51.0 54.0 58.0 60.0 64.0 70.0 75.0 78.0 85.0 90.0 100.0 110.0 120.0 130.0 BR MAX IT (mA) Voltage VC @ Ipp (V) 7.00 7.37 7.98 8.60 9.21 9.83 10.40 11.10 12.30 13.50 14.70 15.90 17.20 18.50 19.70 20.90 22.10 24.50 26.90 29.50 31.90 34.40 36.80 40.60 44.20 49.10 52.80 55.30 58.90 62.70 66.30 71.20 73.70 78.60 86.00 92.10 95.80 104.00 111.00 123.00 135.00 147.00 159.00 10 10 10 10 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 9.2 10.3 11.2 12.0 12.9 13.6 14.4 15.4 17.0 18.2 19.9 21.5 23.2 24.4 26.0 27.6 29.2 32.4 35.5 38.9 42.1 45.4 48.4 53.3 58.1 64.5 69.4 72.7 77.4 82.4 87.1 93.6 96.8 103.0 113.0 121.0 126.0 137.0 146.0 162.0 177.0 193.0 209.0 (Volts) @ IT MIN 6.40 6.67 7.22 7.78 8.33 8.89 9.44 10.00 11.10 12.20 13.30 14.40 15.60 16.70 17.80 18.90 20.00 22.20 24.40 26.70 28.90 31.10 33.30 36.70 40.00 44.40 47.80 50.00 53.30 56.70 60.00 64.40 66.70 71.10 77.80 83.30 86.70 94.40 100.00 111.00 122.00 133.00 144.00 Maximum Maximum Agency Peak Reverse Approval Pulse Leakage IR Current Ipp @ VR (A) (A) 326.1 291.3 267.9 250.0 232.6 220.6 208.3 194.8 176.5 164.8 150.8 139.5 129.3 123.0 115.4 108.7 102.7 92.6 84.5 77.1 71.3 66.1 62.0 56.3 51.6 46.5 43.2 41.3 38.8 36.4 34.4 32.1 31.0 29.1 26.5 24.8 23.8 21.9 20.5 18.5 16.9 15.5 14.4 800 800 500 200 100 50 20 10 5 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X Note: 1. For bidirectional type having VR of 10 volts and less, the IR limit is double. 2. 100% High Temperature Storage Life test and Reflow Simulation. 3. 100% HTRB(High Temperature Reverse Bias). For Unidirectional, 150C/100%VR/96hours, for Bidirectional, 150C/100%VR/192hrs(96hours for each direction for Bidirectional). 4. Each lot of parts will pass group B test requirement. SMDJ-HR Series 2 56 (c)2013 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 11/18/13 Transient Voltage Suppression Diodes Surface Mount - 3000W > SMDJ-HR series Group B Test Requirement Screen Method Condition TM TVS Diode Arrays (SPARequirement Family of Products) Surge test 10/1000 s Peak Pluse Waveform Maximum clamping Voltage (VC) @ Peak Plus Current (IPP) Sample Size 45 perform 10x Accept 0 failures Burn - In (HTRB) MIL -STD-750, Method 1038.5 Applied voltage 100% VR@150C Sample size 45 340 hours (680 hours for bi-direction products, each direction 340 hours) Accept 0 failures IR@VR, V(BR)@IT Sample size 45 Accept 0 failures Electrical test -- I-V Curve Characteristics Bi-directional Uni-directional Ipp Vc VBR VR V IR VF IT IT IR Vc VBR VR IR IT V Ipp Ipp PPPM VR VBR VC IR VF VR VBR Vc Peak Pulse Power Dissipation -- Max power dissipation Stand-off Voltage -- Maximum voltage that can be applied to the TVS without operation Breakdown Voltage -- Maximum current that flows though the TVS at a specified test current (IT) Clamping Voltage -- Peak voltage measured across the suppressor at a specified Ippm (peak impulse current) Reverse Leakage Current -- Current measured at VR Forward Voltage Drop for Uni-directional Ratings and Characteristic Curves (T =25C unless otherwise noted) A Figure 1 - TVS Transients Clamping Waveform Figure 2 - Peak Pulse Power Rating 1000 PPPM-Peak Pulse Power (KW) Voltage Transients Voltage or Current Voltage Across TVS Current Through TVS 100 10 1 0.31x0.31" (8.0x8.0mm) 0.1 Copper Pad Area 0.001 0.01 0.1 1 td-Pulse Width (ms) 10 Time continues on next page. SMDJ-HR Series 3 57 (c)2013 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 11/18/13 Transient Voltage Suppression Diodes Surface Mount - 3000W > SMDJ-HR series Ratings and Characteristic Curves (T =25C unless otherwise noted) (Continued) A TVS Diode Arrays (SPATMFigure Family of Products) 4 - Pulse Waveform Figure 3 - Peak Pulse Power 150 Peak Pluse Power (Single Pluse) 80 IPPM- Peak Pulse Current, % IRSM Peak Pulse Power (PPP) or Current (IPP) Derating in Percentage % 100 60 50 40 Average Power 20 0 0 25 50 75 100 125 150 tr=10sec Peak Value IPPM 100 175 TJ=25C Pulse Width(td) is defined as the point where the peak current decays to 50% of IPPM Half Value IPPM IPPM ( ) 2 50 0 Tj - initial temperature (C) 10/1000sec. Waveform as defined by R.E.A td 1.0 0 2.0 3.0 4.0 t-Time (ms) Figure 5 - Typical Junction Capacitance Figure 6 - Steady State Power Derating Curve 100000 Cj (pF) 10000 PM(AV), Steady Sate Power Dissipation (W) Bi-directional V= OV Uni-directional V= OV 1000 Uni-directional @ VR 100 Bi-directional @ VR 10 1 1.0 10.0 100.0 1000.0 VBR - Reverse Breakdown Voltage (V) 6.5 6 5.5 5 4.5 4 3.5 3 2.5 2 1.5 1 0.5 0 0 25 50 75 100 125 150 175 TA - Ambient Temperature(C) Figure 7 - Maximum Non-Repetitive Peak Forward Surge Current Uni-Directional only IFSM - Peak Forward Surge Current (A) 350 300 250 200 150 100 50 0 1 10 100 Number of Cycles at 60 Hz SMDJ-HR Series 4 58 (c)2013 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 11/18/13 Transient Voltage Suppression Diodes Surface Mount - 3000W > SMDJ-HR series Soldering Parameters TM TVS Diode Arrays Lead-free assembly (SPA Family of Products) Pre Heat - Temperature Min (Ts(min)) 150C - Temperature Max (Ts(max)) 200C - Time (min to max) (ts) 60 - 180 secs Ramp-up TL Average ramp up rate (Liquidus Temp (TL) to peak 3C/second max TS(max) to TL - Ramp-up Rate 3C/second max Reflow - Temperature (TL) (Liquidus) 217C - Time (min to max) (ts) 60 - 150 seconds tL Peak Temperature (TP) 260 20 - 40 seconds Critical Zone TL to TP Ts(max) Ramp-down Ts(min) ts Preheat 25C Time within 5C of actual peak Temperature (tp) +0/-5 tp TP Temperature (T) Reflow Condition t 25C to Peak Time (t) C Ramp-down Rate 6C/second max Time 25C to peak Temperature (TP) 8 minutes Max. Do not exceed 280C Environmental Specifications Physical Specifications High Temp. Storage JESD22-A103 HTRB JESD22-A108 Weight 0.007 ounce, 0.21 grams Thermal Shock JESD22-A106 Case JEDEC DO214AB. Molded plastic body over glass passivated junction MSL JEDEC-J-STD-020C, Level 1 Polarity Color band denotes positive end (cathode) except Bidirectional. H3TRB JESD22-A101 Terminal Matte Tin-plated leads, Solderable per JESD22-B102D RSH JESD22-B106C Dimensions DO-214AB (SMC J-Bend) Dimensions Cathode Band (for Uni-directional products only) C A B H D F E J Inches Min Millimeters Max Min Max A 0.114 0.126 2.900 3.200 B 0.260 0.280 6.600 7.110 C 0.220 0.245 5.590 6.220 D 0.079 0.103 2.060 2.620 E 0.030 0.060 0.760 1.520 F 0.002 0.008 0.051 0.203 G 0.305 0.320 7.750 8.130 H 0.006 0.012 0.152 0.305 G I 0.129 - 3.300 - K J 0.094 - 2.400 - K - 0.165 L 0.094 - L I 4.200 2.400 - Solder Pads (all dimensions in mm) SMDJ-HR Series 5 59 (c)2013 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 11/18/13 Transient Voltage Suppression Diodes Surface Mount - 3000W > SMDJ-HR series Part Numbering System SMDJ XXX C A -HR Part Marking System TVS Diode Arrays (SPATM Family of Products) Cathode Band F (for Uni-directional products only) HIGH RELIABILITY 5% VOLTAGE TOLERANCE XXX BI-DIRECTIONAL YMXXX VOLTAGE Littelfuse Logo Marking Code Trace Code Marking Y:Year Code M: Month Code XXX: Lot Code SERIES Packaging Part number Component Package SMDJxxxXX-HR DO-214AB Packaging Option Quantity 500 Tape & Reel - 16mm/7" tape Packaging Specification EIA STD RS-481 Tape and Reel Specification 0.157 (4.0) Cathode 0.63 (16.0) 0.315 (8.0) 0.059 DIA (1.5) Cover tape 7.0 (187) 0.80 (20.2) Arbor Hole Dia. 0.65 (16.4) SMDJ-HR Series Dimensions are in inches (and millimeters). Direction of Feed 6 60 (c)2013 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 11/18/13