Transient Voltage Suppression Diodes
55
TVS Diode Arrays (SPA
™ Family of Products)
©2013 Littelfuse, Inc.
Specifications are subject to change without notice.
Revised: 11/18/13
Surface Mount – 3000W > SMDJ-HR series
SMDJ-HR Series
AGENCY AGENCY FILE NUMBER
E230531
The SMDJ-HR High Reliability series is designed
specifically to protect sensitive electronic equipment from
voltage transients induced by lightning and other transient
voltage events.
Description
Maximum Ratings and Thermal Characteristics
(TA=25OC unless otherwise noted)
Agency Approvals
Parameter Symbol Value Unit
Peak Pulse Power Dissipation at
TA=25ºC by 10/1000µs waveform
(Fig.1)(Note 1), (Note 2)
PPPM 3000 W
Power Dissipation on infinite heat
sink at TA=50OCPM(AV) 6.5 W
Peak Forward Surge Current, 8.3ms
Single Half Sine Wave (Note 3) IFSM 300 A
Maximum Instantaneous Forward
Voltage at 100A for Unidirectional
only
VF3.5 V
Operating Junction and Storage
Temperature Range TJ, TSTG -55 to 150 °C
Typical Thermal Resistance Junction
to Lead RuJL 15 °C/W
Typical Thermal Resistance Junction
to Ambient RuJA 75 °C/W
Notes:
1. Non-repetitive current pulse , per Fig. 3 and derated above TA = 25OC per Fig. 2.
2. Mounted on copper pad area of 0.31x0.31” (8.0 x 8.0mm) to each terminal.
3. Measured on 8.3ms single half sine wave or equivalent square wave for unidirectional
device only, duty cycle=4 per minute maximum.
TVS devices are ideal for the protection of I/O Interfaces,
VCC bus and other vulnerable circuits used in Telecom,
Computer, Industrial and Consumer electronic applications.
Applications
Features
• Forsurfacemounted
applications in order to
optimize board space
• Lowprolepackage
• Built-instrainrelief
• VBR @TJ= VBR@25°C x (1+αT
x (TJ - 25))
(αT:Temperature Coefficient)
• Glasspassivatedchip
junction
• 3000Wpeakpulsepower
capability at 10/1000μs
waveform, repetition rate
(duty cycles):0.01%
• Fastresponsetime:
typically less than 1.0ps
from0VtoBVmin
• Excellentclamping
capability
• Lowincrementalsurge
resistance
• TypicalIR less than 2µA
above 12V
• Hightemperature
soldering guaranteed:
260°C/40 seconds at
terminals
• Plasticpackagehas
underwriters laboratory
flammability 94V-O
•MeetMSLlevel1,per
J-STD-020, LF maximun
peak of 260°C
• Mattetinlead–freeplated
•HalogenfreeandRoHS
compliant
1
RoHS
SMDJ-HR Series
Functional Diagram
Bi-directional
Uni-directional
Cathode Anode
Uni-directional
Bi-directional
Transient Voltage Suppression Diodes
56
TVS Diode Arrays (SPA
™ Family of Products)
©2013 Littelfuse, Inc.
Specifications are subject to change without notice.
Revised: 11/18/13
Surface Mount – 3000W > SMDJ-HR series
SMDJ-HR Series
Electrical Characteristics
Part
Number
(Uni)
Part
Number
(Bi)
Marking
Reverse
Stand off
Voltage
VR
(Volts)
Breakdown
Voltage VBR
(Volts) @ IT
Test
Current
IT
(mA)
Maximum
Clamping
Voltage VC
@ Ipp
(V)
Maximum
Peak
Pulse
Current Ipp
(A)
Maximum
Reverse
Leakage IR
@ VR
(µA)
Agency
Approval
UNI BI MIN MAX
SMDJ5.0A-HR SMDJ5.0CA-HR RDE DDE 5.0 6.40 7. 0 0 10 9.2 326.1 800 X
SMDJ6.0A-HR SMDJ6.0CA-HR RDG DDG 6.0 6.67 7.37 10 10.3 291.3 800 X
SMDJ6.5A-HR SMDJ6.5CA-HR RDK DDK 6.5 7.22 7.98 10 11. 2 267.9 500 X
SMDJ7.0A-HR SMDJ7.0CA-HR PDM DDM 7. 0 7.78 8.60 10 12.0 250.0 200 X
SMDJ7.5A-HR SMDJ7.5CA-HR PDP DDP 7. 5 8.33 9.21 1 12.9 232.6 100 X
SMDJ8.0A-HR SMDJ8.0CA-HR PDR DDR 8.0 8.89 9.83 1 13.6 220.6 50 X
SMDJ8.5A-HR SMDJ8.5CA-HR PDT DDT 8.5 9.44 10.40 1 14.4 208.3 20 X
SMDJ9.0A-HR SMDJ9.0CA-HR PDV DDV 9.0 10.00 11. 10 1 15.4 194.8 10 X
SMDJ10A-HR SMDJ10CA-HR PDX DDX 10.0 11. 10 12.30 1 1 7. 0 176.5 5 X
SMDJ11A-HR SMDJ11CA-HR PDZ DDZ 11. 0 12.20 13.50 1 18.2 164.8 2 X
SMDJ12A-HR SMDJ12CA-HR PEE DEE 12.0 13.30 14.70 1 19.9 150.8 2 X
SMDJ13A-HR SMDJ13CA-HR PEG DEG 13.0 14.40 15.90 1 21.5 139.5 2 X
SMDJ14A-HR SMDJ14CA-HR PEK DEK 14.0 15.60 17.20 1 23.2 129.3 2 X
SMDJ15A-HR SMDJ15CA-HR PEM DEM 15.0 16.70 18.50 1 24.4 123.0 2 X
SMDJ16A-HR SMDJ16CA-HR PEP DEP 16.0 17.80 19.70 1 26.0 115.4 2 X
SMDJ17A-HR SMDJ17CA-HR PER DER 1 7. 0 18.90 20.90 1 27.6 108.7 2 X
SMDJ18A-HR SMDJ18CA-HR PET DET 18.0 20.00 22.10 1 29.2 102.7 2 X
SMDJ20A-HR SMDJ20CA-HR PEV DEV 20.0 22.20 24.50 1 32.4 92.6 2 X
SMDJ22A-HR SMDJ22CA-HR PEX DEX 22.0 24.40 26.90 1 35.5 84.5 2 X
SMDJ24A-HR SMDJ24CA-HR PEZ DEZ 24.0 26.70 29.50 1 38.9 77.1 2 X
SMDJ26A-HR SMDJ26CA-HR PFE DFE 26.0 28.90 31.90 1 42.1 71.3 2 X
SMDJ28A-HR SMDJ28CA-HR PFG DFG 28.0 31.10 34.40 1 45.4 66.1 2 X
SMDJ30A-HR SMDJ30CA-HR PFK DFK 30.0 33.30 36.80 1 48.4 62.0 2 X
SMDJ33A-HR SMDJ33CA-HR PFM DFM 33.0 36.70 40.60 1 53.3 56.3 2 X
SMDJ36A-HR SMDJ36CA-HR PFP DFP 36.0 40.00 44.20 1 58.1 51.6 2 X
SMDJ40A-HR SMDJ40CA-HR PFR DFR 40.0 44.40 49.10 1 64.5 46.5 2 X
SMDJ43A-HR SMDJ43CA-HR PFT DFT 43.0 47.80 52.80 1 69.4 43.2 2 X
SMDJ45A-HR SMDJ45CA-HR PFV FVH 45.0 50.00 55.30 1 72.7 41.3 2 X
SMDJ48A-HR SMDJ48CA-HR PFX FXH 48.0 53.30 58.90 1 77.4 38.8 2 X
SMDJ51A-HR SMDJ51CA-HR PFZ FZH 51.0 56.70 62.70 1 82.4 36.4 2 X
SMDJ54A-HR SMDJ54CA-HR RGE GEH 54.0 60.00 66.30 1 87.1 34.4 2 X
SMDJ58A-HR SMDJ58CA-HR PGG GGH 58.0 64.40 71.20 1 93.6 32.1 2 X
SMDJ60A-HR SMDJ60CA-HR PGK GKH 60.0 66.70 73.70 1 96.8 31.0 2 X
SMDJ64A-HR SMDJ64CA-HR PGM GMH 64.0 71.10 78.60 1 103.0 29.1 2 X
SMDJ70A-HR SMDJ70CA-HR PGP GPH 70.0 77.80 86.00 1 113.0 26.5 2 X
SMDJ75A-HR SMDJ75CA-HR PGR GRH 75.0 83.30 92.10 1 121.0 24.8 2 X
SMDJ78A-HR SMDJ78CA-HR PGT GTH 78.0 86.70 95.80 1 126.0 23.8 2 X
SMDJ85A-HR SMDJ85CA-HR PGV GVH 85.0 94.40 104.00 1 137.0 21.9 2 X
SMDJ90A-HR SMDJ90CA-HR PGX GXH 90.0 100.00 111.0 0 1 146.0 20.5 2 X
SMDJ100A-HR SMDJ100CA-HR PGZ GZH 100.0 111.0 0 123.00 1 162.0 18.5 2 X
SMDJ110A-HR SMDJ110CA-HR PHE HEH 110.0 122.00 135.00 1 177.0 16.9 2 X
SMDJ120A-HR SMDJ120CA-HR PHG HGH 120.0 133.00 147.00 1 193.0 15.5 2 X
SMDJ130A-HR SMDJ130CA-HR PHK HKH 130.0 144.00 159.00 1 209.0 14.4 2 X
Note:
1. For bidirectional type having VR of 10 volts and less, the IR limit is double.
2. 100% High Temperature Storage Life test and Reflow Simulation.
3.100%HTRB(HighTemperatureReverseBias).ForUnidirectional,150C/100%VR/96hours,
forBidirectional,150C/100%VR/192hrs(96hoursforeachdirectionforBidirectional).
4.EachlotofpartswillpassgroupBtestrequirement.
2
Transient Voltage Suppression Diodes
57
TVS Diode Arrays (SPA
™ Family of Products)
©2013 Littelfuse, Inc.
Specifications are subject to change without notice.
Revised: 11/18/13
Surface Mount – 3000W > SMDJ-HR series
SMDJ-HR Series
Voltage Transients
Time
Voltage Across TVS
Current Through TVS
Voltage or Current
Figure 1 - TVS Transients Clamping Waveform
Ratings and Characteristic Curves (TA=25°C unless otherwise noted)
Figure 2 - Peak Pulse Power Rating
0.1
1
10
100
1000
0.001 0.01 0.11
P
PPM
-Peak Pulse Power (KW)
10
0.31x0.31" (8.0x8.0mm)
Copper Pad Area
t
d
-Pulse Width (ms)
Vc VBR VR
IR
IT
Ipp
V
Uni-directional
VF
Vc VBR VR
IR
IT
Ipp
V
Vc
VBR
VR
Ipp
IR
IT
Bi-directional
PPPM Peak Pulse Power Dissipation -- Max power dissipation
VR Stand-off Voltage -- Maximum voltage that can be applied to the TVS without operation
VBR Breakdown Voltage -- Maximum current that flows though the TVS at a specified test current (IT)
VC Clamping Voltage -- Peak voltage measured across the suppressor at a specified Ippm (peak impulse current)
IR Reverse Leakage Current -- Current measured at VR
VF Forward Voltage Drop for Uni-directional
continues on next page.
3
Group B Test Requirement
Screen Method Condition Requirement
Surge test 10/1000 µs Peak
Pluse Waveform
Maximum clamping
Voltage (VC) @ Peak
Plus Current (IPP)
Sample Size 45 perform 10x
Accept 0 failures
Burn-In
(HTRB)
MIL -STD-750,
Method 1038.5
Applied voltage
100% VR@150°C
Sample size 45
340 hours (680 hours for
bi-direction products, each
direction 340 hours)
Accept 0 failures
Electricaltest -- IR@VR, V(BR)@IT
Sample size 45
Accept 0 failures
I-V Curve Characteristics
Transient Voltage Suppression Diodes
58
TVS Diode Arrays (SPA
™ Family of Products)
©2013 Littelfuse, Inc.
Specifications are subject to change without notice.
Revised: 11/18/13
Surface Mount – 3000W > SMDJ-HR series
SMDJ-HR Series
Ratings and Characteristic Curves (TA=25°C unless otherwise noted) (Continued)
IPPM- Peak Pulse Current, % IRSM
0
0
50
100
150
1.0 2.0 3.0 4.0
tr=10µsec
Peak Value
IPPM
IPPM
2
TJ=25°C
Pulse Width(td) is defined
as the point where the peak
current decays to 50% of IPPM
10/1000µsec. Waveform
as defined by R.E.A
td
t-Time (ms)
Half Value
IPPM ( )
1
10
100
1000
10000
100000
1.010.0100.0 1000.0
Cj (pF)
VBR - Reverse Breakdown Voltage (V)
Bi-directional V
= OV
Uni-directional
@ VR
Bi-directional
@ VR
Uni-directional V
= OV
0
0.5
1
1.5
2
2.5
3
3.5
4
4.5
5
5.5
6
6.5
0255075100 125150 175
P
M(AV)
, Steady Sate Power
Dissipation (W)
TA - Ambient Temperature(ºC)
Figure 4 - Pulse Waveform
Figure 5 - Typical Junction Capacitance Figure 6 - Steady State Power Derating Curve
110100
Number of Cycles at 60 Hz
0
50
100
150
200
250
300
350
IFSM - Peak Forward Surge Current
(A)
Figure 7 - Maximum Non-Repetitive Peak Forward
Surge Current Uni-Directional only
0
20
40
60
80
100
0255075100 125 150 175
Peak Pulse Power (P
PP
) or Current
(I
PP
) Derating in Percentage %
T
j
- initial temperature (ºC)
50
Peak Pluse Power
(Single Pluse)
Average Power
Figure 3 - Peak Pulse Power
4
Transient Voltage Suppression Diodes
59
TVS Diode Arrays (SPA
™ Family of Products)
©2013 Littelfuse, Inc.
Specifications are subject to change without notice.
Revised: 11/18/13
Surface Mount – 3000W > SMDJ-HR series
SMDJ-HR Series
Physical Specifications
Weight 0.007 ounce, 0.21 grams
Case JEDECDO214AB.Moldedplasticbody
over glass passivated junction
Polarity Color band denotes positive end
(cathode)exceptBidirectional.
Terminal Matte Tin-plated leads, Solderable per
JESD22-B102D
Dimensions
Dimensions Inches Millimeters
Min Max Min Max
A 0.114 0.126 2.900 3.200
B0.260 0.280 6.600 7. 11 0
C 0.220 0.245 5.590 6.220
D 0.079 0.103 2.060 2.620
E0.030 0.060 0.760 1.520
F 0.002 0.008 0.051 0.203
G 0.305 0.320 7.750 8.130
H 0.006 0.012 0.152 0.305
I 0.129 - 3.300 -
J 0.094 - 2.400 -
K - 0.165 4.200
L 0.094 - 2.400 -
Environmental Specifications
Soldering Parameters
Temperature (T)
Time (t)
Ts(min)
Ts(max)
TL
TP
ts
Preheat
tL
tp
Ramp-up Critical Zone
TL to TP
Ramp-down
t 25˚C to Peak
25˚C
Reflow Condition Lead–freeassembly
Pre Heat
- Temperature Min (Ts(min))150°C
- Temperature Max (Ts(max))200°C
- Time (min to max) (ts)60–180secs
Average ramp up rate (Liquidus Temp
(TL) to peak 3°C/second max
TS(max) to TL - Ramp-up Rate 3°C/second max
Reflow - Temperature (TL) (Liquidus) 217°C
- Time (min to max) (ts)60–150seconds
Peak Temperature (TP)260+0/-5 °C
Time within 5°C of actual peak
Temperature (tp)20–40seconds
Ramp-down Rate 6°C/second max
Time 25°C to peak Temperature (TP)8 minutes Max.
Do not exceed 280°C
(all dimensions in mm)
I
L
K
J
Solder Pads
5
High Temp. Storage JESD22-A103
HTRB JESD22-A108
Thermal Shock JESD22-A106
MSL JEDEC-J-STD-020C,Level1
H3TRB JESD22-A101
RSH JESD22-B106C
DO-214AB (SMC J-Bend)
B
F
G
H
E
C
D
A
Cathode Band
(for Uni-directional products only)
Transient Voltage Suppression Diodes
60
TVS Diode Arrays (SPA
™ Family of Products)
©2013 Littelfuse, Inc.
Specifications are subject to change without notice.
Revised: 11/18/13
Surface Mount – 3000W > SMDJ-HR series
SMDJ-HR Series
Part Numbering System
Packaging
Part number Component
Package Quantity Packaging
Option
Packaging
Specification
SMDJxxxXX-HR DO-214AB 500 Tape&Reel–16mm/7”tape EIASTDRS-481
Part Marking System
VOLTAGE
BI-DIRECTIONAL
5% VOLTAGE TOLERANCE
SERIES
SMDJ -HR XXX CA
HIGH RELIABILITY
Tape and Reel Specification
0.63
(16.0)
0.315
(8.0)
0.157
(4.0)
0.65
(16.4)
0.80 (20.2)
Arbor Hole Dia.
7.0 (187)
Dimensions are in inches
(and millimeters).
Direction of Feed
0.059 DIA
(1.5) Cover tape
Cathode
6
F
XXX
YMXXX
Marking Code
Trace Code Marking
Y:Year Code
M: Month Code
XXX: Lot Code
Littelfuse Logo
Cathode Band
(for Uni-directional products only)