TPS2041A, TPS2042A, TPS2043A, TPS2044A TPS2051A, TPS2052A, TPS2053A, TPS2054A CURRENT-LIMITED POWER-DISTRIBUTION SWITCHES SLVS247 - SEPTEMBER 2000 D D D D D D D D D D D D 80-m High-Side MOSFET Switch 500 mA Continuous Current Per Channel Independent Thermal and Short-Circuit Protection With Overcurrent Logic Output Operating Range . . . 2.7 V to 5.5 V CMOS- and TTL-Compatible Enable Inputs 2.5-ms Typical Rise Time Undervoltage Lockout 10 A Maximum Standby Supply Current for Single and Dual (20 A for Triple and Quad) Bidirectional Switch Ambient Temperature Range, 0C to 85C ESD Protection UL Listed - File No. E169910 description TPS2041A, TPS2051A D PACKAGE (TOP VIEW) GND IN IN EN 1 8 2 7 3 6 4 OUT OUT OUT OC 5 TPS2043A, TPS2053A D PACKAGE (TOP VIEW) GNDA IN1 EN1 EN2 GNDB IN2 EN3 NC 1 16 2 15 3 14 4 13 5 12 6 11 7 10 8 9 OC1 OUT1 OUT2 OC2 OC3 OUT3 NC NC TPS2042A, TPS2052A D PACKAGE (TOP VIEW) GND IN EN1 EN2 1 8 2 7 3 6 4 5 OC1 OUT1 OUT2 OC2 TPS2044A, TPS2054A D PACKAGE (TOP VIEW) GNDA IN1 EN1 EN2 GNDB IN2 EN3 EN4 1 16 2 15 3 14 4 13 5 12 6 11 7 10 8 9 OC1 OUT1 OUT2 OC2 OC3 OUT3 OUT4 OC4 The TPS2041A through TPS2044A and All enable inputs are active high for the TPS205xA series. TPS2051A through TPS2054A power-distribution NC - No connect switches are intended for applications where heavy capacitive loads and short circuits are likely to be encountered. These devices incorporate 80-m N-channel MOSFET high-side power switches for power-distribution systems that require multiple power switches in a single package. Each switch is controlled by an independent logic enable input. Gate drive is provided by an internal charge pump designed to control the power-switch rise times and fall times to minimize current surges during switching. The charge pump requires no external components and allows operation from supplies as low as 2.7 V. When the output load exceeds the current-limit threshold or a short is present, these devices limit the output current to a safe level by switching into a constant-current mode, pulling the overcurrent (OCx) logic output low. When continuous heavy overloads and short circuits increase the power dissipation in the switch, causing the junction temperature to rise, a thermal protection circuit shuts off the switch to prevent damage. Recovery from a thermal shutdown is automatic once the device has cooled sufficiently. Internal circuitry ensures the switch remains off until valid input voltage is present. These power-distribution switches are designed to current limit at 0.9 A. GENERAL SWITCH CATALOG 33 m, single TPS201xA 0.2 A - 2 A TPS202x TPS203x 80 m, single TPS2014 TPS2015 TPS2041 TPS2051 TPS2045 TPS2055 80 m, dual 0.2 A - 2 A 0.2 A - 2 A 600 mA 1A 500 mA 500 mA 250 mA 250 mA 260 m IN1 OUT IN2 1.3 TPS2042 TPS2052 TPS2046 TPS2056 500 mA 500 mA 250 mA 250 mA TPS2100/1 IN1 500 mA IN2 10 mA TPS2102/3/4/5 IN1 500 mA IN2 100 mA 80 m, dual TPS2080 TPS2081 TPS2082 TPS2090 TPS2091 TPS2092 500 mA 500 mA 500 mA 250 mA 250 mA 250 mA 80 m, triple TPS2043 TPS2053 TPS2047 TPS2057 500 mA 500 mA 250 mA 250 mA 80 m, quad TPS2044 TPS2054 TPS2048 TPS2058 500 mA 500 mA 250 mA 250 mA 80 m, quad TPS2085 TPS2086 TPS2087 TPS2095 TPS2096 TPS2097 500 mA 500 mA 500 mA 250 mA 250 mA 250 mA Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. Copyright 2000, Texas Instruments Incorporated PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 1 TPS2041A, TPS2042A, TPS2043A, TPS2044A TPS2051A, TPS2052A, TPS2053A, TPS2054A CURRENT-LIMITED POWER-DISTRIBUTION SWITCHES SLVS247 - SEPTEMBER 2000 AVAILABLE OPTIONS TA ENABLE RECOMMENDED MAXIMUM CONTINUOUS LOAD CURRENT (A) TYPICAL SHORT-CIRCUIT CURRENT LIMIT AT 25C (A) PACKAGED DEVICES NUMBER OF SWITCHES Active low Single Active high Active low 0C to 85C Active high Active low Dual 05 0.5 09 0.9 Triple Active high Active low Active high The D package is available taped and reeled. Add an R suffix to device type (e.g., TPS2041ADR) 2 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 Quad SOIC (D) TPS2041AD TPS2051AD TPS2042AD TPS2052AD TPS2043AD TPS2053AD TPS2044AD TPS2054AD TPS2041A, TPS2042A, TPS2043A, TPS2044A TPS2051A, TPS2052A, TPS2053A, TPS2054A CURRENT-LIMITED POWER-DISTRIBUTION SWITCHES SLVS247 - SEPTEMBER 2000 functional block diagrams TPS2041A Power Switch CS IN OUT Charge Pump EN Current Limit Driver OC UVLO Thermal Sense GND Current sense Active high for TPS205xA series TPS2042A OC1 Thermal Sense GND EN1 Current Limit Driver Charge Pump CS OUT1 UVLO Power Switch IN CS OUT2 Charge Pump Driver Current Limit OC2 EN2 Thermal Sense Current sense Active high for TPS205xA series POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 3 TPS2041A, TPS2042A, TPS2043A, TPS2044A TPS2051A, TPS2052A, TPS2053A, TPS2054A CURRENT-LIMITED POWER-DISTRIBUTION SWITCHES SLVS247 - SEPTEMBER 2000 functional block diagrams TPS2043A OC1 Thermal Sense GNDA EN1 Current Limit Driver Charge Pump CS OUT1 UVLO Power Switch CS IN1 OUT2 Charge Pump Current Limit Driver OC2 EN2 Thermal Sense Power Switch CS IN2 OUT3 Charge Pump EN3 Driver Current Limit OC3 UVLO Thermal Sense GNDB Current sense Active high for TPS205xA series 4 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 TPS2041A, TPS2042A, TPS2043A, TPS2044A TPS2051A, TPS2052A, TPS2053A, TPS2054A CURRENT-LIMITED POWER-DISTRIBUTION SWITCHES SLVS247 - SEPTEMBER 2000 functional block diagrams OC1 TPS2044A Thermal Sense GNDA EN1 Driver Current Limit Charge Pump CS OUT 1 UVLO Power Switch IN1 OUT 2 CS Charge Pump Driver Current Limit OC2 EN2 Thermal Sense OC3 Thermal Sense GNDB EN3 Driver Current Limit Charge Pump CS OUT3 UVLO Power Switch CS IN2 OUT4 Charge Pump Driver Current Limit OC4 EN4 Thermal Sense Current sense Active high for TPS205xA series POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 5 TPS2041A, TPS2042A, TPS2043A, TPS2044A TPS2051A, TPS2052A, TPS2053A, TPS2054A CURRENT-LIMITED POWER-DISTRIBUTION SWITCHES SLVS247 - SEPTEMBER 2000 Terminal Functions TPS2041A and TPS2051A TERMINAL NAME I/O NO. DESCRIPTION TPS2041A TPS2051A EN 4 - I Enable input. Logic low turns on power switch. EN - 4 I Enable input. Logic high turns on power switch. GND 1 1 I Ground IN 2, 3 2, 3 I Input voltage OC 5 5 O Overcurrent. Logic output active low 6, 7, 8 6, 7, 8 O Power-switch output OUT TPS2042A and TPS2052A TERMINAL NAME I/O NO. DESCRIPTION TPS2042A TPS2052A EN1 3 - I Enable input. Logic low turns on power switch, IN-OUT1. EN2 4 - I Enable input. Logic low turns on power switch, IN-OUT2. EN1 - 3 I Enable input. Logic high turns on power switch, IN-OUT1. EN2 - 4 I Enable input. Logic high turns on power switch, IN-OUT2. GND 1 1 I Ground IN 2 2 I Input voltage OC1 8 8 O Overcurrent. Logic output active low, for power switch, IN-OUT1 OC2 5 5 O Overcurrent. Logic output active low, for power switch, IN-OUT2 OUT1 7 7 O Power-switch output OUT2 6 6 O Power-switch output 6 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 TPS2041A, TPS2042A, TPS2043A, TPS2044A TPS2051A, TPS2052A, TPS2053A, TPS2054A CURRENT-LIMITED POWER-DISTRIBUTION SWITCHES SLVS247 - SEPTEMBER 2000 Terminal Functions (Continued) TPS2043A and TPS2053A TERMINAL NAME I/O NO. DESCRIPTION TPS2043A TPS2053A EN1 3 - I Enable input, logic low turns on power switch, IN1-OUT1. EN2 4 - I Enable input, logic low turns on power switch, IN1-OUT2. EN3 7 - I Enable input, logic low turns on power switch, IN2-OUT3. EN1 - 3 I Enable input, logic high turns on power switch, IN1-OUT1. EN2 - 4 I Enable input, logic high turns on power switch, IN1-OUT2. EN3 - 7 I Enable input, logic high turns on power switch, IN2-OUT3. GNDA 1 1 Ground for IN1 switch and circuitry. GNDB 5 5 Ground for IN2 switch and circuitry. IN1 2 2 I Input voltage IN2 6 6 I Input voltage NC 8, 9, 10 8, 9, 10 OC1 16 16 O Overcurrent, logic output active low, IN1-OUT1 OC2 13 13 O Overcurrent, logic output active low, IN1-OUT2 OC3 12 12 O Overcurrent, logic output active low, IN2-OUT3 OUT1 15 15 O Power-switch output, IN1-OUT1 OUT2 14 14 O Power-switch output, IN1-OUT2 OUT3 11 11 O Power-switch output, IN2-OUT3 No connection TPS2044A and TPS2054A TERMINAL NAME NO. I/O DESCRIPTION TPS2044A TPS2054A EN1 3 - I Enable input. logic low turns on power switch, IN1-OUT1. EN2 4 - I Enable input. Logic low turns on power switch, IN1-OUT2. EN3 7 - I Enable input. Logic low turns on power switch, IN2-OUT3. EN4 8 - I Enable input. Logic low turns on power switch, IN2-OUT4. EN1 - 3 I Enable input. Logic high turns on power switch, IN1-OUT1. EN2 - 4 I Enable input. Logic high turns on power switch, IN1-OUT2. EN3 - 7 I Enable input. Logic high turns on power switch, IN2-OUT3. EN4 - 8 I Enable input. Logic high turns on power switch, IN2-OUT4. GNDA 1 1 Ground for IN1 switch and circuitry. GNDB 5 5 Ground for IN2 switch and circuitry. IN1 2 2 I Input voltage IN2 6 6 I Input voltage OC1 16 16 O Overcurrent. Logic output active low, IN1-OUT1 OC2 13 13 O Overcurrent. Logic output active low, IN1-OUT2 OC3 12 12 O Overcurrent. Logic output active low, IN2-OUT3 OC4 9 9 O Overcurrent. Logic output active low, IN2-OUT4 OUT1 15 15 O Power-switch output, IN1-OUT1 OUT2 14 14 O Power-switch output, IN1-OUT2 OUT3 11 11 O Power-switch output, IN2-OUT3 OUT4 10 10 O Power-switch output, IN2-OUT4 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 7 TPS2041A, TPS2042A, TPS2043A, TPS2044A TPS2051A, TPS2052A, TPS2053A, TPS2054A CURRENT-LIMITED POWER-DISTRIBUTION SWITCHES SLVS247 - SEPTEMBER 2000 detailed description power switch The power switch is an N-channel MOSFET with a maximum on-state resistance of 135 m (VI(IN) = 5 V). Configured as a high-side switch, the power switch prevents current flow from OUT to IN and IN to OUT when disabled. The power switch supplies a minimum of 500 mA per switch. charge pump An internal charge pump supplies power to the driver circuit and provides the necessary voltage to pull the gate of the MOSFET above the source. The charge pump operates from input voltages as low as 2.7 V and requires very little supply current. driver The driver controls the gate voltage of the power switch. To limit large current surges and reduce the associated electromagnetic interference (EMI) produced, the driver incorporates circuitry that controls the rise times and fall times of the output voltage. The rise and fall times are typically in the 2-ms to 4-ms range. enable (ENx, ENx) The logic enable disables the power switch and the bias for the charge pump, driver, and other circuitry to reduce the supply current. The supply current is reduced to less than 10 A on the single and dual devices (20 A on the triple and quad devices) when a logic high is present on ENx (TPS204xA) or a logic low is present on ENx (TPS205xA). A logic zero input on ENx or a logic high on ENx restores bias to the drive and control circuits and turns the power on. The enable input is compatible with both TTL and CMOS logic levels. overcurrent (OCx) The OCx open-drain output is asserted (active low) when an overcurrent or overtemperature condition is encountered. The output will remain asserted until the overcurrent or overtemperature condition is removed. current sense A sense FET monitors the current supplied to the load. The sense FET measures current more efficiently than conventional resistance methods. When an overload or short circuit is encountered, the current-sense circuitry sends a control signal to the driver. The driver in turn reduces the gate voltage and drives the power FET into its saturation region, which switches the output into a constant-current mode and holds the current constant while varying the voltage on the load. thermal sense The TPS204xA and TPS205xA implement a dual-threshold thermal trip to allow fully independent operation of the power distribution switches. In an overcurrent or short-circuit condition the junction temperature rises. When the die temperature rises to approximately 140C, the internal thermal sense circuitry checks to determine which power switch is in an overcurrent condition and turns off that switch, thus isolating the fault without interrupting operation of the adjacent power switch. Hysteresis is built into the thermal sense, and after the device has cooled approximately 20 degrees, the switch turns back on. The switch continues to cycle off and on until the fault is removed. The (OCx) open-drain output is asserted (active low) when overtemperature or overcurrent occurs. undervoltage lockout A voltage sense circuit monitors the input voltage. When the input voltage is below approximately 2 V, a control signal turns off the power switch. Product series designations TPS204x and TPS205x refer to devices presented in this data sheet and not necessarily to other TI devices numbered in this sequence. 8 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 TPS2041A, TPS2042A, TPS2043A, TPS2044A TPS2051A, TPS2052A, TPS2053A, TPS2054A CURRENT-LIMITED POWER-DISTRIBUTION SWITCHES SLVS247 - SEPTEMBER 2000 absolute maximum ratings over operating free-air temperature range (unless otherwise noted) Input voltage range, VI(IN) (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3 V to 6 V Output voltage range, VO(OUT) (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3 V to VI(IN) + 0.3 V Input voltage range, VI(ENx) or VI(ENx) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3 V to 6 V Continuous output current, IO(OUT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . internally limited Continuous total power dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . See Dissipation Rating Table Operating virtual junction temperature range, TJ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0C to 125C Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -65C to 150C Lead temperature soldering 1,6 mm (1/16 inch) from case for 10 seconds . . . . . . . . . . . . . . . . . . . . . . . 260C Electrostatic discharge (ESD) protection: Human body model MIL-STD-883C . . . . . . . . . . . . . . . . . . . . . 2 kV Machine model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.2 kV Stresses beyond those listed under "absolute maximum ratings" may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under "recommended operating conditions" is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. NOTE 1: All voltages are with respect to GND. DISSIPATION RATING TABLE PACKAGE TA 25C POWER RATING DERATING FACTOR ABOVE TA = 25C TA = 70C POWER RATING TA = 85C POWER RATING D-8 725 mW 5.9 mW/C 464 mW 377 mW D-16 1123 mW 9 mW/C 719 mW 584 mW recommended operating conditions MIN MAX 2.7 5.5 V Input voltage, VI(EN) or VI(EN) 0 5.5 V Continuous output current, IO(OUT) (per switch) 0 500 mA Operating virtual junction temperature, TJ 0 125 C Input voltage, VI(IN) POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 UNIT 9 TPS2041A, TPS2042A, TPS2043A, TPS2044A TPS2051A, TPS2052A, TPS2053A, TPS2054A CURRENT-LIMITED POWER-DISTRIBUTION SWITCHES SLVS247 - SEPTEMBER 2000 electrical characteristics over recommended operating junction temperature range, VI(IN)= 5.5 V, IO = rated current, VI(EN) = 0 V, VI(EN) = VI(IN) (unless otherwise noted) power switch PARAMETER Static drain-source on-state resistance, 5-V operation rDS( DS(on)) Static drain-source on-state resistance, 3.3-V operation tr tf Rise time, time output Fall time, time output TEST CONDITIONS TPS204xA MIN TPS205xA TYP MAX MIN TYP MAX VI(IN) = 5 V, IO = 0.5 A TJ = 25C, 80 100 80 100 VI(IN) = 5 V, IO = 0.5 A TJ = 85C, 90 120 90 120 VI(IN) = 5 V, IO = 0.5 A TJ = 125C, 100 135 100 135 VI(IN) = 3.3 V, IO = 0.5 A TJ = 25C, 90 125 90 125 VI(IN) = 3.3 V, IO = 0.5 A TJ = 85C, 110 145 110 145 VI(IN) = 3.3 V, IO = 0.5 A TJ = 125C, 120 160 120 160 VI(IN) = 5.5 V, CL = 1 F, TJ = 25C, RL=10 2.5 2.5 VI(IN) = 2.7 V, CL = 1 F, TJ = 25C, RL=10 3 3 VI(IN) = 5.5 V, CL = 1 F, VI(IN) = 2.7 V, CL = 1 F, TJ = 25C, RL=10 4.4 4.4 TJ = 25C, RL=10 2.5 2.5 UNIT m ms ms Pulse-testing techniques maintain junction temperature close to ambient temperature; thermal effects must be taken into account separately. enable input ENx or ENx PARAMETER VIH High-level input voltage VIL Low level input voltage Low-level II Input current ton toff Turnon time TPS204xA TPS205xA Turnoff time TEST CONDITIONS 2.7 V VI(IN) 5.5 V TPS204xA MIN TYP TPS205xA MAX 2 MIN TYP MAX 2 V 4.5 V VI(IN) 5.5 V 0.8 0.8 2.7 V VI(IN) 4.5 V 0.4 0.4 VI(ENx) = 0 V or VI(ENx) = VI(IN) VI(ENx) = VI(IN) or VI(ENx) = 0 V -0.5 0.5 -0.5 CL = 100 F, RL=10 CL = 100 F, RL=10 UNIT 0.5 20 20 40 40 V A ms current limit PARAMETER IOS Short-circuit output current TEST CONDITIONS VI(IN) = 5 V, OUT connected to GND, Device enabled into short circuit TPS204xA MIN 0.7 TYP 1 TPS205xA MAX MIN 1.3 0.7 TYP 1 MAX 1.3 UNIT A Pulse-testing techniques maintain junction temperature close to ambient temperature; thermal effects must be taken into account separately. 10 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 TPS2041A, TPS2042A, TPS2043A, TPS2044A TPS2051A, TPS2052A, TPS2053A, TPS2054A CURRENT-LIMITED POWER-DISTRIBUTION SWITCHES SLVS247 - SEPTEMBER 2000 electrical characteristics over recommended operating junction temperature range, VI(IN)= 5.5 V, IO = rated current, VI(EN) = 0 V, VI(EN) = VI(IN) (unless otherwise noted) (continued) supply current (TPS2041A, TPS2051A) PARAMETER Supply y current,, low-level output Supply y current,, high-level output Leakage current Reverse leakage current TPS2041A TEST CONDITIONS MIN VI(EN) = VI(IN) TJ = 25C -40C TJ 125C VI(EN) = 0 V TJ = 25C -40C TJ 125C VI(EN) = 0 V TJ = 25C -40C TJ 125C VI(EN) = VI(IN) TJ = 25C -40C TJ 125C OUT connected to ground VI(EN) = VI(IN) -40C TJ 125C VI(EN)= 0 V -40C TJ 125C IN = High g impedance VI(EN) = 0 V VI(EN) = VI(IN) TJ = 25C No Load on OUT No Load on OUT TYP 0.025 TPS2051A MAX MIN TYP MAX 0.025 1 UNIT 1 10 A 10 85 110 100 85 110 A 100 100 A 100 0.3 A 0.3 supply current (TPS2042A, TPS2052A) PARAMETER Supply y current,, low-level output Supply y current,, high-level output Leakage current Reverse leakage current TPS2042A TEST CONDITIONS MIN VI(ENx) = VI(IN) TJ = 25C -40C TJ 125C VI(EN I(ENx)) = 0 V TJ = 25C -40C TJ 125C VI(ENx) ( )=0V TJ = 25C -40C TJ 125C VI(EN I(ENx)) = VI(IN) TJ = 25C -40C TJ 125C OUT connected to ground VI(ENx) = VI(IN) -40C TJ 125C VI(ENx) = 0 V -40C TJ 125C IN = high g impedance VI(EN) = 0 V VI(EN) = VI(IN) TJ = 25C No Load on OUT No Load on OUT POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 TYP 0.025 TPS2052A MAX MIN TYP MAX 0.025 1 UNIT 1 10 A 10 85 110 100 85 110 A 100 100 A 100 0.3 0.3 A 11 TPS2041A, TPS2042A, TPS2043A, TPS2044A TPS2051A, TPS2052A, TPS2053A, TPS2054A CURRENT-LIMITED POWER-DISTRIBUTION SWITCHES SLVS247 - SEPTEMBER 2000 electrical characteristics over recommended operating junction temperature range, VI(IN)= 5.5 V, IO = rated current, VI(EN) = 0 V, VI(EN) = VI(IN) (unless otherwise noted) (continued) supply current (TPS2043A, TPS2053A) PARAMETER TPS2043A TEST CONDITIONS Supply y current,, low-level output No Load on OUTx Supply y current,, high-level output No Load on OUTx MIN VI(ENx) = VI(INx) TJ = 25C -40C TJ 125C VI(EN I(ENx)) = 0 V TJ = 25C -40C TJ 125C VI(ENx) = 0 V TJ = 25C -40C TJ 125C VI(EN I(ENx)) = VI(IN I(INx)) TJ = 25C -40C TJ 125C Leakage current OUTx connected to ground VI(ENx) = VI(INx) VI(ENx) = 0 V Reverse leakage g current IN = high g impedance VI(ENx) = 0 V VI(ENx) = VI(IN) TYP 0.05 TPS2053A MAX MIN TYP MAX 0.05 2 UNIT 2 20 A 20 160 200 200 160 200 A 200 -40C TJ 125C 200 -40C TJ 125C A 200 0.3 TJ = 25C A 0.3 supply current (TPS2044A, TPS2054A) PARAMETER TPS2044A TEST CONDITIONS Supply y current,, low-level output No Load on OUTx Supply y current,, high-level output No Load on OUTx MIN VI(ENx) = VI(INx) TJ = 25C -40C TJ 125C VI(EN I(ENx)) = 0 V TJ = 25C -40C TJ 125C VI(ENx) = 0 V TJ = 25C -40C TJ 125C VI(EN I(ENx)) = VI(IN I(INx)) TJ = 25C -40C TJ 125C Leakage current OUTx connected to ground VI(ENx) = VI(INx) VI(ENx) = 0 V Reverse leakage g current IN = high g impedance VI(EN) = 0 V VI(EN) = VI(IN) TYP 0.05 TPS2054A MAX MIN TYP MAX 0.05 2 UNIT 2 20 A 20 170 220 200 170 220 A 200 -40C TJ 125C 200 -40C TJ 125C A 200 0.3 TJ = 25C A 0.3 undervoltage lockout PARAMETER TEST CONDITIONS TPS204xA MIN Low-level input voltage Hysteresis TYP 2 TJ = 25C TPS205xA MAX MIN 2.5 2 100 TYP MAX 2.5 100 UNIT V mV overcurrent OC PARAMETER Sink current Output low voltage Off-state current TEST CONDITIONS VO = 5 V IO = 5 V, VOL(OC) VO = 5 V, VO = 3.3 V TPS204xA MIN Specified by design, not production tested. 12 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 TYP TPS205xA MAX MIN TYP MAX UNIT 10 10 mA 0.5 0.5 V 1 1 A TPS2041A, TPS2042A, TPS2043A, TPS2044A TPS2051A, TPS2052A, TPS2053A, TPS2054A CURRENT-LIMITED POWER-DISTRIBUTION SWITCHES SLVS247 - SEPTEMBER 2000 PARAMETER MEASUREMENT INFORMATION OUT RL tf tr CL VO(OUT) 90% 10% 90% 10% TEST CIRCUIT 50% 50% VI(EN) toff ton 50% toff ton 90% VO(OUT) 50% VI(EN) 90% VO(OUT) 10% 10% VOLTAGE WAVEFORMS Figure 1. Test Circuit and Voltage Waveforms VI(EN) (5 V/div) VI(EN) (5 V/div) VI(IN) = 5 V TA = 25C CL = 0.1 F RL = 10 VO(OUT) (2 V/div) 0 1 2 3 4 5 6 7 8 9 VI(IN) = 5 V TA = 25C CL = 0.1 F RL = 10 VO(OUT) (2 V/div) 10 0 2 t - Time - ms Figure 2. Turnon Delay and Rise Time with 0.1-F Load POST OFFICE BOX 655303 4 6 8 10 12 t - Time - ms 14 16 18 20 Figure 3. Turnoff Delay and Fall Time with 0.1-F Load * DALLAS, TEXAS 75265 13 TPS2041A, TPS2042A, TPS2043A, TPS2044A TPS2051A, TPS2052A, TPS2053A, TPS2054A CURRENT-LIMITED POWER-DISTRIBUTION SWITCHES SLVS247 - SEPTEMBER 2000 PARAMETER MEASUREMENT INFORMATION VI(EN) (5 V/div) VI(EN) (5 V/div) VI(IN) = 5 V TA = 25C CL = 1 F RL = 10 VO(OUT) (2 V/div) 0 1 2 3 4 5 6 7 8 VI(IN) = 5 V TA = 25C CL = 1 F RL = 10 VO(OUT) (2 V/div) 9 0 10 2 4 6 8 10 12 14 16 18 20 t - Time - ms t - Time - ms Figure 4. Turnon Delay and Rise Time with 1-F Load Figure 5. Turnoff Delay and Fall Time with 1-F Load VI(IN) = 5 V TA = 25C VI(EN) (5 V/div) VO(OUT) (2 V/div) VI(IN) = 5 V TA = 25C IO(OUT) (0.5 A/div) 0 1 2 3 4 5 6 7 8 9 IO(OUT) (0.5 A/div) 10 0 10 Figure 6. TPS2051A, Short-Circuit Current, Device Enabled into Short 14 20 30 40 50 60 70 80 90 100 t - Time - ms t - Time - ms POST OFFICE BOX 655303 Figure 7. TPS2051A, Threshold Trip Current with Ramped Load on Enabled Device * DALLAS, TEXAS 75265 TPS2041A, TPS2042A, TPS2043A, TPS2044A TPS2051A, TPS2052A, TPS2053A, TPS2054A CURRENT-LIMITED POWER-DISTRIBUTION SWITCHES SLVS247 - SEPTEMBER 2000 PARAMETER MEASUREMENT INFORMATION VI(EN) (5 V/div) VO(OC) (5 V/div) 470 F 220 F 100 F VI(IN) = 5 V TA = 25C Ramp = 1 A/100 ms IO(OUT) (0.5 A/div) 0 20 40 60 VI(IN) = 5 V TA = 25C RL = 10 IO(OUT) (0.2 A/div) 80 100 120 140 160 180 200 0 2 4 t - Time - ms 6 8 10 12 Figure 8. OC Response With Ramped Load on Enabled Device VO(OC) (5 V/div) IO(OUT) (0.5 A/div) IO(OUT) (1 A/div) 2000 3000 18 20 VI(IN) = 5 V TA = 25C VO(OC) (5 V/div) 1000 16 Figure 9. Inrush Current with 100-F, 220-F and 470-F Load Capacitance VI(IN) = 5 V TA = 25C 0 14 t - Time - ms 4000 5000 0 t - Time - s 200 400 600 800 1000 t - Time - s Figure 10. 4- Load Connected to Enabled Device POST OFFICE BOX 655303 Figure 11. 1- Load Connected to Enabled Device * DALLAS, TEXAS 75265 15 TPS2041A, TPS2042A, TPS2043A, TPS2044A TPS2051A, TPS2052A, TPS2053A, TPS2054A CURRENT-LIMITED POWER-DISTRIBUTION SWITCHES SLVS247 - SEPTEMBER 2000 TYPICAL CHARACTERISTICS TURNON DELAY TIME vs INPUT VOLTAGE TURNOFF DELAY TIME vs INPUT VOLTAGE 3.5 12 CL = 1 F RL = 10 TA = 25C Turnon Delay Time - ms Turnon Delay Time - ms 3.2 CL = 1 F RL = 10 TA = 25C 2.9 2.6 10 8 6 2.3 2 2.5 3 3.5 4 4.5 5 5.5 4 2.5 6 3 VI - Input Voltage - V 3.5 4 4.5 5 VI - Input Voltage - V Figure 12 5.5 6 5.5 6 Figure 13 RISE TIME vs INPUT VOLTAGE FALL TIME vs INPUT VOLTAGE 3 2.2 CL = 1 F RL = 10 TA = 25C 2.1 CL = 1 F RL = 10 TA = 25C f t - Fall Time - ms r t - Rise Time - ms 2.7 2.4 2 1.9 1.8 1.7 2.1 1.6 1.8 2.5 3 3.5 4 4.5 5 5.5 6 1.5 2.5 3 VI - Input Voltage - V Figure 14 16 3.5 4 4.5 5 VI - Input Voltage - V Figure 15 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 TPS2041A, TPS2042A, TPS2043A, TPS2044A TPS2051A, TPS2052A, TPS2053A, TPS2054A CURRENT-LIMITED POWER-DISTRIBUTION SWITCHES SLVS247 - SEPTEMBER 2000 TYPICAL CHARACTERISTICS SUPPLY CURRENT, OUTPUT ENABLED vs JUNCTION TEMPERATURE SUPPLY CURRENT, OUTPUT DISABLED vs JUNCTION TEMPERATURE 160 I I(IN) - Supply Current, Output Disabled - nA I I(IN) - Supply Current, Output Enabled - A 100 90 VI(IN) = 5.5 V VI(IN) = 5 V 80 VI(IN) = 4.5 V 70 VI(IN) = 2.7 V 60 VI(IN) = 3.3 V 50 40 -40 0 25 85 TJ - Junction Temperature - C 140 VI(IN) = 5.5 V 120 VI(IN) = 5 V 100 VI(IN) = 4.5 V 80 VI(IN) = 3.3 V 60 VI(IN) = 2.7 V 40 20 0 -40 125 0 25 STATIC DRAIN-SOURCE ON-STATE RESISTANCE vs JUNCTION TEMPERATURE IO = 0.5 A 140 VI(IN) = 2.7 V VI(IN) = 3.3 V 120 VI(IN) = 3 V 100 80 VI(IN) = 5 V 60 VI(IN) = 4.5 V 40 20 0 0 25 125 Figure 17 85 INPUT-TO-OUTPUT VOLTAGE vs LOAD CURRENT VI(IN) - VO(OUT) - Input-to-Output Voltage - mV r DS(on) - Static Drain-Source On-State Resistance - m Figure 16 160 85 TJ - Junction Temperature - C 125 70 TA = 25C VI(IN) = 2.7 V 60 VI(IN) = 4.5 V 50 VI(IN) = 3.3 V 40 VI(IN) = 5 V 30 20 10 0 100 TJ - Junction Temperature - C 200 300 400 500 IL - Load Current - A Figure 18 Figure 19 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 17 TPS2041A, TPS2042A, TPS2043A, TPS2044A TPS2051A, TPS2052A, TPS2053A, TPS2054A CURRENT-LIMITED POWER-DISTRIBUTION SWITCHES SLVS247 - SEPTEMBER 2000 TYPICAL CHARACTERISTICS SHORT-CIRCUIT OUTPUT CURRENT vs JUNCTION TEMPERATURE THRESHOLD TRIP CURRENT vs INPUT VOLTAGE 1.2 TA = 25C Load Ramp = 1 A/10 ms VI(IN) = 5.5 V 1.1 VI(IN) = 5 V 1.16 VI(IN) = 4.5 V Threshold Trip Current - A I OS - Short-circuit Output Current - A 1.2 1 VI(IN) = 3.3 V 0.9 VI(IN) = 2.7 V 0.8 1.08 1.04 0.7 0.6 -40 1.12 25 85 0 TJ - Junction Temperature - C 1 2.5 125 3 Figure 20 6 CURRENT-LIMIT RESPONSE vs PEAK CURRENT 2.35 250 VI(IN) = 5 V TA = 25C 2.3 Start Threshold Current Limit Response - s UVLO - Undervoltage Lockout - V 5.5 Figure 21 UNDERVOLTAGE LOCKOUT vs JUNCTION TEMPERATURE 2.25 Stop Threshold 2.2 200 150 100 50 2.15 2.1 0 -40 0 25 85 TJ - Junction Temperature - C 125 0 2.5 5 Figure 23 POST OFFICE BOX 655303 7.5 Peak Current - A Figure 22 18 3.5 4 4.5 5 VI - Input Voltage - V * DALLAS, TEXAS 75265 10 12.5 TPS2041A, TPS2042A, TPS2043A, TPS2044A TPS2051A, TPS2052A, TPS2053A, TPS2054A CURRENT-LIMITED POWER-DISTRIBUTION SWITCHES SLVS247 - SEPTEMBER 2000 APPLICATION INFORMATION TPS2041A 2,3 Power Supply 2.7 V to 5.5 V IN 0.1 F OUT 6,7,8 Load 0.1 F 5 4 22 F OC EN GND 1 Figure 24. Typical Application (Example, TPS2041A) power-supply considerations A 0.01-F to 0.1-F ceramic bypass capacitor between INx and GND, close to the device, is recommended. Placing a high-value electrolytic capacitor on the output pin(s) is recommended when the output load is heavy. This precaution reduces power-supply transients that may cause ringing on the input. Additionally, bypassing the output with a 0.01-F to 0.1-F ceramic capacitor improves the immunity of the device to short-circuit transients. overcurrent A sense FET is employed to check for overcurrent conditions. Unlike current-sense resistors, sense FETs do not increase the series resistance of the current path. When an overcurrent condition is detected, the device maintains a constant output current and reduces the output voltage accordingly. Complete shutdown occurs only if the fault is present long enough to activate thermal limiting. Three possible overload conditions can occur. In the first condition, the output has been shorted before the device is enabled or before VI(IN) has been applied (see Figure 6). The TPS204xA and TPS205xA sense the short and immediately switch into a constant-current output. In the second condition, a short or an overload occurs while the device is enabled. At the instant the overload occurs, very high currents may flow for a short time before the current-limit circuit can react. After the current-limit circuit has tripped (reached the overcurrent trip threshhold) the device switches into constant-current mode. In the third condition, the load has been gradually increased beyond the recommended operating current. The current is permitted to rise until the current-limit threshold is reached or until the thermal limit of the device is exceeded (see Figure 7). The TPS204xA and TPS205xA are capable of delivering current up to the current-limit threshold without damaging the device. Once the threshold has been reached, the device switches into its constant-current mode. OC response The OC open-drain output is asserted (active low) when an overcurrent or overtemperature condition is encountered. The output will remain asserted until the overcurrent or overtemperature condition is removed. Connecting a heavy capacitive load to an enabled device can cause momentary false overcurrent reporting from the inrush current flowing through the device, charging the downstream capacitor. The TPS204xA and TPS205xA family of devices are designed to reduce false overcurrent reporting. An internal overcurrent transient filter eliminates the need for external components to remove unwanted pulses. Using low-ESR electrolytic capacitors on the output lowers the inrush current flow through the device during hot-plug events by providing a low-impedance energy source, also reducing erroneous overcurrent reporting. POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 19 TPS2041A, TPS2042A, TPS2043A, TPS2044A TPS2051A, TPS2052A, TPS2053A, TPS2054A CURRENT-LIMITED POWER-DISTRIBUTION SWITCHES SLVS247 - SEPTEMBER 2000 APPLICATION INFORMATION TPS2041A GND OUT IN OUT IN OUT EN V+ Rpullup OC Figure 25. Typical Circuit for OC Pin (Example, TPS2041A) power dissipation and junction temperature The low on-resistance on the n-channel MOSFET allows small surface-mount packages, such as SOIC, to pass large currents. The thermal resistances of these packages are high compared to those of power packages; it is good design practice to check power dissipation and junction temperature. Begin by determining the rDS(on) of the N-channel MOSFET relative to the input voltage and operating temperature. As an initial estimate, use the highest operating ambient temperature of interest and read rDS(on) from Figure 18. Using this value, the power dissipation per switch can be calcultaed by: P D + rDS(on) I2 Depending on which device is being used, multiply this number by the number of switches being used. This step will render the total power dissipation from the N-channel MOSFETs. Finally, calculate the junction temperature: T J Where: + PD R qJA ) TA TA = Ambient Temperature C RJA = Thermal resistance SOIC = 172C/W (for 8 pin), 111C/W (for 16 pin) PD = Total power dissipation based on number of switches being used. Compare the calculated junction temperature with the initial estimate. If they do not agree within a few degrees, repeat the calculation, using the calculated value as the new estimate. Two or three iterations are generally sufficient to get a reasonable answer. thermal protection Thermal protection prevents damage to the IC when heavy-overload or short-circuit faults are present for extended periods of time. The faults force the TPS204xA and TPS205xA into constant-current mode, which causes the voltage across the high-side switch to increase; under short-circuit conditions, the voltage across the switch is equal to the input voltage. The increased dissipation causes the junction temperature to rise to high levels. The protection circuit senses the junction temperature of the switch and shuts it off. Hysteresis is built into the thermal sense circuit, and after the device has cooled approximately 20 degrees, the switch turns back on. The switch continues to cycle in this manner until the load fault or input power is removed. The TPS204xA and TPS205xA implement a dual thermal trip to allow fully independent operation of the power distribution switches. In an overcurrent or short-circuit condition the junction temperature will rise. Once the die temperature rises to approximately 140C, the internal thermal sense circuitry checks which power switch is in an overcurrent condition and turns that power switch off, thus isolating the fault without interrupting operation of the adjacent power switch. Should the die temperature exceed the first thermal trip point of 140C and reach 160C, both switches turn off. The OC open-drain output is asserted (active low) when overtemperature or overcurrent occurs. 20 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 TPS2041A, TPS2042A, TPS2043A, TPS2044A TPS2051A, TPS2052A, TPS2053A, TPS2054A CURRENT-LIMITED POWER-DISTRIBUTION SWITCHES SLVS247 - SEPTEMBER 2000 APPLICATION INFORMATION undervoltage lockout (UVLO) An undervoltage lockout ensures that the power switch is in the off state at power up. Whenever the input voltage falls below approximately 2 V, the power switch will be quickly turned off. This facilitates the design of hot-insertion systems where it is not possible to turn off the power switch before input power is removed. The UVLO will also keep the switch from being turned on until the power supply has reached at least 2 V, even if the switch is enabled. Upon reinsertion, the power switch will be turned on, with a controlled rise time to reduce EMI and voltage overshoots. universal serial bus (USB) applications The universal serial bus (USB) interface is a 12-Mb/s, or 1.5-Mb/s, multiplexed serial bus designed for low-to-medium bandwidth PC peripherals (e.g., keyboards, printers, scanners, and mice). The four-wire USB interface is conceived for dynamic attach-detach (hot plug-unplug) of peripherals. Two lines are provided for differential data, and two lines are provided for 5-V power distribution. USB data is a 3.3-V level signal, but power is distributed at 5 V to allow for voltage drops in cases where power is distributed through more than one hub across long cables. Each function must provide its own regulated 3.3 V from the 5-V input or its own internal power supply. The USB specification defines the following five classes of devices, each differentiated by power-consumption requirements: D D D D D Hosts/self-powered hubs (SPH) Bus-powered hubs (BPH) Low-power, bus-powered functions High-power, bus-powered functions Self-powered functions Self-powered and bus-powered hubs distribute data and power to downstream functions. The TPS204xA and TPS205xA can provide power-distribution solutions for many of these classes of devices. host/self-powered and bus-powered hubs Hosts and self-powered hubs have a local power supply that powers the embedded functions and the downstream ports (see Figures 26 and 27). This power supply must provide from 5.25 V to 4.75 V to the board side of the downstream connection under full-load and no-load conditions. Hosts and SPHs are required to have current-limit protection and must report overcurrent conditions to the USB controller. Typical SPHs are desktop PCs, monitors, printers, and stand-alone hubs. Power Supply 3.3 V Downstream USB Ports 5V TPS2041A 2, 3 IN 0.1 F OUT D+ D- 7 0.1 F 5 USB Control 4 120 F VBUS GND OC EN GND Figure 26. Typical One-Port Solution POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 21 TPS2041A, TPS2042A, TPS2043A, TPS2044A TPS2051A, TPS2052A, TPS2053A, TPS2054A CURRENT-LIMITED POWER-DISTRIBUTION SWITCHES SLVS247 - SEPTEMBER 2000 APPLICATION INFORMATION Downstream USB Ports D+ Power Supply D- 3.3 V 5V + TPS2044A 2 6 IN1 OUT1 IN2 33 F 15 D+ 0.1 F D- 14 OUT2 11 3 13 USB Controller 4 12 7 9 8 OC1 OUT3 VBUS GND + 33 F VBUS GND 11 EN1 D+ OC2 D- EN2 + 10 OC3 33 F VBUS GND OUT4 EN3 OC4 D+ EN4 D- GNDA GNDB 1 5 + 33 F VBUS GND Figure 27. Typical Four-Port USB Host/Self-Powered Hub Bus-powered hubs obtain all power from upstream ports and often contain an embedded function. The hubs are required to power up with less than one unit load. The BPH usually has one embedded function, and power is always available to the controller of the hub. If the embedded function and hub require more than 100 mA on powerup, the power to the embedded function may need to be kept off until enumeration is completed. This can be accomplished by removing power or by shutting off the clock to the embedded function. Power switching the embedded function is not necessary if the aggregate power draw for the function and controller is less than one unit load. The total current drawn by the bus-powered device is the sum of the current to the controller, the embedded function, and the downstream ports, and it is limited to 500 mA from an upstream port. 22 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 TPS2041A, TPS2042A, TPS2043A, TPS2044A TPS2051A, TPS2052A, TPS2053A, TPS2054A CURRENT-LIMITED POWER-DISTRIBUTION SWITCHES SLVS247 - SEPTEMBER 2000 APPLICATION INFORMATION low-power bus-powered functions and high-power bus-powered functions Both low-power and high-power bus-powered functions obtain all power from upstream ports; low-power functions always draw less than 100 mA; high-power functions must draw less than 100 mA at power up and can draw up to 500 mA after enumeration. If the load of the function is more than the parallel combination of 44 and 10 F at power up, the device must implement inrush current limiting (see Figure 28). Power Supply D+ 3.3 V TPS2041A D- VBUS GND 2,3 10 F 0.1 F IN OUT 6, 7, 8 0.1 F 5 USB Control 4 10 F Internal Function OC EN GND 1 Figure 28. High-Power Bus-Powered Function (Example, TPS2041A) USB power-distribution requirements USB can be implemented in several ways, and, regardless of the type of USB device being developed, several power-distribution features must be implemented. D D D Hosts/self-powered hubs must: - Current-limit downstream ports - Report overcurrent conditions on USB VBUS Bus-powered hubs must: - Enable/disable power to downstream ports - Power up at <100 mA - Limit inrush current (<44 and 10 F) Functions must: - Limit inrush currents - Power up at <100 mA The feature set of the TPS204xA and TPS205xA allows them to meet each of these requirements. The integrated current-limiting and overcurrent reporting is required by hosts and self-powered hubs. The logic-level enable and controlled rise times meet the need of both input and output ports on bus-power hubs, as well as the input ports for bus-power functions (see Figures 29 through 32). POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 23 TPS2041A, TPS2042A, TPS2043A, TPS2044A TPS2051A, TPS2052A, TPS2053A, TPS2054A CURRENT-LIMITED POWER-DISTRIBUTION SWITCHES SLVS247 - SEPTEMBER 2000 APPLICATION INFORMATION TUSB2040 Hub Controller Upstream Port SN75240 BUSPWR A C B D GANGED D+ D- DP0 DP1 DM0 DM1 Tie to TPS2041A EN Input D+ A C B D GND OC 5V IN DM2 5 V Power Supply EN Ferrite Beads 5V 33 F DP3 OUT DM3 A C B D 1 F TPS76333 SN75240 3.3 V 4.7 F D+ D- Ferrite Beads GND DP4 IN 0.1 F 4.7 F D- GND SN75240 DP2 TPS2041A Downstream Ports VCC DM4 5V TPS2041A GND GND PWRON1 EN OVRCUR1 OC IN 0.1 F 33 F OUT D+ TPS2041A 48-MHz Crystal XTAL1 PWRON2 EN OVRCUR2 OC D- IN Ferrite Beads 0.1 F GND OUT Tuning Circuit XTAL2 OCSOFF 5V TPS2041A PWRON3 EN OVRCUR3 OC IN 0.1 F 33 F OUT D+ GND TPS2041A PWRON4 EN OVRCUR4 OC Ferrite Beads IN 0.1 F OUT GND 5V 33 F USB rev 1.1 requires 120 F per hub. Figure 29. Hybrid Self/Bus-Powered Hub Implementation, TPS2041A 24 D- POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 TPS2041A, TPS2042A, TPS2043A, TPS2044A TPS2051A, TPS2052A, TPS2053A, TPS2054A CURRENT-LIMITED POWER-DISTRIBUTION SWITCHES SLVS247 - SEPTEMBER 2000 APPLICATION INFORMATION TUSB2040 Hub Controller Upstream Port SN75240 BUSPWR A C B D GANGED D+ D- DP0 DP1 DM0 DM1 Tie to TPS2042A EN Input D+ A C B D GND OC 5V IN DM2 5 V Power Supply EN Ferrite Beads 5V 33 F DP3 OUT DM3 A C B D 1 F TPS76333 SN75240 3.3 V 4.7 F D+ D- Ferrite Beads GND DP4 IN 0.1 F 4.7 F VCC DM4 5V TPS2042A GND GND 48-MHz Crystal D- GND SN75240 DP2 TPS2041A Downstream Ports PWRON1 EN1 OUT1 OVRCUR1 OC1 OUT2 PWRON2 EN2 OVRCUR2 OC2 33 F D+ IN 0.1 F XTAL1 D- Ferrite Beads GND TPS2042A Tuning Circuit XTAL2 OCSOFF PWRON3 EN1 OUT1 OVRCUR3 OC1 OUT2 PWRON4 EN2 OVRCUR4 OC2 5V 33 F IN D+ 0.1 F GND Ferrite Beads D- GND 5V 33 F USB rev 1.1 requires 120 F per hub. Figure 30. Hybrid Self/Bus-Powered Hub Implementation, TPS2042A POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 25 TPS2041A, TPS2042A, TPS2043A, TPS2044A TPS2051A, TPS2052A, TPS2053A, TPS2054A CURRENT-LIMITED POWER-DISTRIBUTION SWITCHES SLVS247 - SEPTEMBER 2000 APPLICATION INFORMATION TUSB2040 Hub Controller 1/2 SN75240 BUSPWR A C B D GANGED Upstream Port D+ D- DP0 DP1 DM0 DM1 Tie to TPS2043A EN Input D+ A C B D GND OC 5V IN DM2 5 V Power Supply EN Ferrite Beads 5V 47 F DP3 OUT DM3 A C B D 1 F TPS76333 1/2 SN75240 3.3 V 4.7 F D+ D- Ferrite Beads GND DP4 IN 0.1 F 4.7 F D- GND SN75240 DP2 TPS2041A Downstream Ports VCC DM4 5V TPS2043A GND GND 48-MHz Crystal XTAL1 Tuning Circuit XTAL2 PWRON1 EN1 OUT1 OVRCUR1 OC1 OUT2 PWRON2 EN2 OVRCUR2 OC2 47 F D+ IN1 0.1 F D- Ferrite Beads GND PWRON3 OVRCUR3 5V EN3 OUT3 OC3 47 F OCSOFF IN2 0.1 F GND GNDA GNDB USB rev 1.1 requires 120 F per hub. Figure 31. Hybrid Self/Bus-Powered Hub Implementation, TPS2043A 26 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 TPS2041A, TPS2042A, TPS2043A, TPS2044A TPS2051A, TPS2052A, TPS2053A, TPS2054A CURRENT-LIMITED POWER-DISTRIBUTION SWITCHES SLVS247 - SEPTEMBER 2000 APPLICATION INFORMATION TUSB2040 Hub Controller Upstream Port SN75240 BUSPWR A C B D GANGED D+ D- DP0 DP1 DM0 DM1 Tie to TPS2041 EN Input D+ A C B D GND OC 5V IN DM2 5 V Power Supply EN Ferrite Beads 5V 33 F DP3 OUT DM3 A C B D 1 F TPS76333 SN75240 3.3 V 4.7 F D+ D- Ferrite Beads GND DP4 IN 0.1 F 4.7 F D- GND SN75240 DP2 TPS2041A Downstream Ports VCC DM4 5V TPS2044A GND GND 48-MHz Crystal XTAL1 Tuning Circuit XTAL2 PWRON1 EN1 OUT1 OVRCUR1 OC1 OUT2 PWRON2 EN2 OVRCUR2 OC2 33 F D+ IN1 0.1 F D- Ferrite Beads GND OCSOFF PWRON3 EN3 OUT3 OVRCUR3 OC3 OUT4 PWRON4 EN4 OVRCUR4 OC4 5V 33 F IN2 D+ 0.1 F GND Ferrite Beads GNDA D- GND GNDB 5V 33 F USB rev 1.1 requires 120 F per hub. Figure 32. Hybrid Self/Bus-Powered Hub Implementation, TPS2044A POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 27 TPS2041A, TPS2042A, TPS2043A, TPS2044A TPS2051A, TPS2052A, TPS2053A, TPS2054A CURRENT-LIMITED POWER-DISTRIBUTION SWITCHES SLVS247 - SEPTEMBER 2000 APPLICATION INFORMATION generic hot-plug applications (see Figure 33) In many applications it may be necessary to remove modules or pc boards while the main unit is still operating. These are considered hot-plug applications. Such implementations require the control of current surges seen by the main power supply and the card being inserted. The most effective way to control these surges is to limit and slowly ramp the current and voltage being applied to the card, similar to the way in which a power supply normally turns on. Due to the controlled rise times and fall times of the TPS204xA and TPS205xA, these devices can be used to provide a softer start-up to devices being hot-plugged into a powered system. The UVLO feature of the TPS204xA and TPS205xA also ensures the switch will be off after the card has been removed, and the switch will be off during the next insertion. The UVLO feature insures a soft start with a controlled rise time for every insertion of the card or module. PC Board TPS2041A Power Supply 2.7 V to 5.5 V 1000 F Optimum 0.1 F GND OUT IN OUT IN OUT EN Block of Circuitry OC Overcurrent Response Figure 33. Typical Hot-Plug Implementation (Example, TPS2041A) By placing the TPS204xA and TPS205xA between the VCC input and the rest of the circuitry, the input power will reach these devices first after insertion. The typical rise time of the switch is approximately 2.5 ms, providing a slow voltage ramp at the output of the device. This implementation controls system surge currents and provides a hot-plugging mechanism for any device. 28 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 PACKAGE OPTION ADDENDUM www.ti.com 4-Aug-2008 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Drawing Pins Package Eco Plan (2) Qty TPS2041AD NRND SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS2041ADG4 NRND SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS2041ADR NRND SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS2041ADRG4 NRND SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS2042AD NRND SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS2042ADG4 NRND SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS2042ADR NRND SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS2042ADRG4 NRND SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS2043AD NRND SOIC D 16 40 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS2043ADG4 NRND SOIC D 16 40 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS2043ADR NRND SOIC D 16 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS2043ADRG4 NRND SOIC D 16 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS2044AD NRND SOIC D 16 40 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS2044ADG4 NRND SOIC D 16 40 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS2044ADR NRND SOIC D 16 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS2044ADRG4 NRND SOIC D 16 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS2051AD NRND SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS2051ADG4 NRND SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS2051ADR NRND SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS2051ADRG4 NRND SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS2052AD NRND SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS2052ADG4 NRND SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS2052ADR NRND SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS2052ADRG4 NRND SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS2053AD NRND SOIC D 16 CU NIPDAU Level-1-260C-UNLIM 40 Addendum-Page 1 Green (RoHS & no Sb/Br) Lead/Ball Finish MSL Peak Temp (3) PACKAGE OPTION ADDENDUM www.ti.com 4-Aug-2008 Orderable Device Status (1) Package Type Package Drawing Pins Package Eco Plan (2) Qty TPS2053ADG4 NRND SOIC D 16 TPS2053ADR NRND SOIC D TPS2053ADRG4 NRND SOIC TPS2054AD NRND TPS2054ADG4 40 Lead/Ball Finish MSL Peak Temp (3) Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM 16 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM D 16 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SOIC D 16 40 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM NRND SOIC D 16 40 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS2054ADR NRND SOIC D 16 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS2054ADRG4 NRND SOIC D 16 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 2 PACKAGE MATERIALS INFORMATION www.ti.com 13-Jul-2011 TAPE AND REEL INFORMATION *All dimensions are nominal Device Package Package Pins Type Drawing TPS2041ADR SOIC D TPS2042ADR SOIC TPS2043ADR SOIC TPS2044ADR SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant 5.2 2.1 8.0 12.0 Q1 8 2500 330.0 12.4 6.4 D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1 D 16 2500 330.0 16.4 6.5 10.3 2.1 8.0 16.0 Q1 SOIC D 16 2500 330.0 16.4 6.5 10.3 2.1 8.0 16.0 Q1 TPS2051ADR SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1 TPS2052ADR SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1 TPS2053ADR SOIC D 16 2500 330.0 16.4 6.5 10.3 2.1 8.0 16.0 Q1 TPS2054ADR SOIC D 16 2500 330.0 16.4 6.5 10.3 2.1 8.0 16.0 Q1 Pack Materials-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 13-Jul-2011 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) TPS2041ADR SOIC D 8 2500 340.5 338.1 20.6 TPS2042ADR SOIC D 8 2500 340.5 338.1 20.6 TPS2043ADR SOIC D 16 2500 333.2 345.9 28.6 TPS2044ADR SOIC D 16 2500 333.2 345.9 28.6 TPS2051ADR SOIC D 8 2500 340.5 338.1 20.6 TPS2052ADR SOIC D 8 2500 340.5 338.1 20.6 TPS2053ADR SOIC D 16 2500 333.2 345.9 28.6 TPS2054ADR SOIC D 16 2500 333.2 345.9 28.6 Pack Materials-Page 2 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI's standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Audio www.ti.com/audio Communications and Telecom www.ti.com/communications Amplifiers amplifier.ti.com Computers and Peripherals www.ti.com/computers Data Converters dataconverter.ti.com Consumer Electronics www.ti.com/consumer-apps DLP(R) Products www.dlp.com Energy and Lighting www.ti.com/energy DSP dsp.ti.com Industrial www.ti.com/industrial Clocks and Timers www.ti.com/clocks Medical www.ti.com/medical Interface interface.ti.com Security www.ti.com/security Logic logic.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Power Mgmt power.ti.com Transportation and Automotive www.ti.com/automotive Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com Wireless www.ti.com/wireless-apps RF/IF and ZigBee(R) Solutions www.ti.com/lprf TI E2E Community Home Page e2e.ti.com Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2011, Texas Instruments Incorporated