G5V-2-H1-DC24 - Omron - Datasheet.Directory

Low Signal Relay G5V-2 63

Low Signal Relay

G5V-2

Miniature Relay for Signal Circuits

• Suitable for handling low signals in computer peripherals,

telecommunications and security equipment.

• Capable of switching loads 10μA to 2 A.

• Conforms to FCC part 68 1,500 V surge withstand.

• Reliable Ag + Au-clad, bifurcated crossbar contacts.

• Fully-sealed construction.

• RoHS Compliant.

FCC

Ordering Information

To Order: Select the part number and add the desired coil voltage rating (e.g., G5V-2-DC12).

Model Number Legend

Specifications

■Contact Data

Note: P level: λ60 = 0.1 x 10–6/operation

This value was measured at a switching frequency of 120 operations/min and the criterion of contact resistance is 50 Ω. This value may vary

depending on the switching frequency and operating environment. Always double-check relay suitability under actual operating conditions.

Type Contact form Construction Model

Standard DPDT Fully-sealed G5V-2

High-sensitivity G5V-2-H1

1. Contact Form

2: DPDT

2. Coil type

Blank: Standard

H1: High-sensitivity

3. Rated Coil Voltage

3, 5, 6, 9, 12, 24, 48 VDC

G5V - - DC

1 32

Item Standard High-sensitivity

Load Resistive load (p.f. = 1)

Rated load 0.50 A at 125 VAC

2 A at 30 VDC

0.5 A at 125 VAC

1 A at 24 VDC

Contact material Ag (Au clad)

Carry current 2 A

Max. operating voltage 125 VAC

125 VDC

Max. operating current 2 A 1 A

Max. switching capacity 62.5 VA

60W

62.5 VA

24W

Min. permissible load (See note) 10 μA, 10 mVDC

64 Low Signal Relay G5V-2

■Coil Data

Standard Type

High-sensitivity Type

Note: 1. The rated current and coil resistance are measured at a coil temperature of 23°C with a tolerance of ±10%.

2. The operating characteristics are measured at a coil temperature of 23°C.

3. The maximum voltage is the highest voltage that can be imposed on the relay coil.

Characteristics

Note: 1. The contact resistance was measured with 10 mA at 1 VDC with a fall-of-potential method.

2. Values in parentheses are typical values unless otherwise stated.

The insulation resistance was measured with a 500-VDC megohmmeter applied to the same parts as those for checking the dielectric strength.

4. The above values are initial values.

Rated voltage

(VDC)

Rated current

(mA)

Coil

resistance

(Ω)

Coil inductance

(Ref. value) (H)

Pick-up

voltage

Dropout

voltage

Maximum

voltage

Power

consumption

(mW)

Armature OFF Armature ON % of rated voltage

3 166.70 18 0.04 0.05 75% max. 5% min. 120% max.

at 23°C

Approx. 500

5 100 50 0.09 0.11

6 83.30 72 0.16 0.19

9 55.60 162 0.31 0.49

12 41.70 288 0.47 0.74

24 20.80 1,152 1.98 2.63

48 12 4,000 7.23 10.00 Approx. 580

Rated voltage

(VDC)

Rated current

(mA)

Coil

resistance

(Ω)

Coil inductance

(Ref. value) (H)

Pick-up

voltage

Dropout

voltage

Maximum

voltage

Power

consumption

(mW)

Armature OFF Armature ON % of rated voltage

3 50 60 0.18 0.57 75% max. 5% min. 180% max.

at 23°C

Approx. 150

5 30 166.7 0.46 0.71

6 25 240 0.70 0.97

9 16.70 540 1.67 2.33

12 12.50 960 2.90 3.99

24 8.33 2,880 6.72 9.27 Approx. 200

48 6.25 7,680 20.10 26.70 150% max.

at 23°C

Approx. 300

Contact resistance (See note 1) 50 mΩ max. (G5V-2); 100 mΩ max. (G5V-2-H1)

Operate time (See note 2) 7 ms max. (mean value: approx. 3.5 ms)

Release time (See note 2) 3 ms max. (mean value: approx. 0.8 ms)

Operating frequency

(max.)

Mechanical 36,000 operations/hour

Electrical 1,800 operations/hour (under rated load)

Insulation resistance (See note 3) 1,000 MΩ min (at 500 VDC)

Dielectric strength 1,000 VAC, 50/60 Hz for 1 minute between coil and contacts

1,000 VAC, 50/60 Hz for 1 minute between contacts of different poles

750 VAC, 50/60 Hz for 1 minute between contacts of same poles

(500 VAC, 50/60 Hz for 1 minute between contacts of same poles for high-sensitive type)

Surge withstand voltage 1,500 V (10 X 160 μs) between coil and contacts (conforms to part 68 of FCC rules)

Vibration Mechanical durability 10 to 55 Hz, 1.50 mm double amplitude

Malfunction

durability

Shock Mechanical durability 1,000 m/s2 (approx. 100 G)

Malfunction

durability 200 m/s2 (approx. 20 G), 100 m/s2 (approx. 10 G) for high-sensitive type

Ambient temperature Operating/storage -25° to 70°C (“-H1” versions) with no icing

-25° to 65°C (standard versions) with no icing

Humidity 5% to 85% RH

Service life Mechanical 15 million operations min. (at operating frequency of 36,000 operations/hour)

Electrical

100,000 operations min. (at 1,800 operations/hr), standard models. See “Characteristic Data”

Weight Approx. 5 g

Low Signal Relay G5V-2 65

■Characteristic Data

G5V-2

G5V-2-H1

Maximum Switching Capacity Ambient Temperature vs.

Maximum Coil Voltage

Electrical Service Life

Rated operating current (A)

Rated operating voltage (V) Rated operating current (A)

Service Life (x10 operations)

Ambient temperature (°)

Maximum coil voltage (%)

Coil rated voltage

3 to 24 VDC

48 VDC

30-VDC

resistive

load

125-VAC resistive

load

123

AC resistive load

resistive

load

Note: The maximum coil voltage refers to the maximum value in a varying range of operating

power voltage, not a continuous voltage.

Maximum Switching Capacity Ambient Temperature vs.

Maximum Coil Voltage

Electrical Service Life

Rated operating current (A)

Rated operating voltage (V) Rated operating current (A)

Service life (x10 operations)

Ambient temperature (°)

Maximum coil voltage (%)

AC resistive

load

DC resistive load

0.7

0.5

0.3

0.2

0.1

24-VDC resistive load

125-VAC resistive load

1000

500

300

100

3 to 24 VDC

48 VDC

200

180

160

140

120

100

Note: The maximum coil voltage refers to the maximum value in a varying range of operating

power voltage, not a continuous voltage.

66 Low Signal Relay G5V-2

Dimensions

Note: 1. All units are in millimeters unless otherwise indicated.

2. Tolerance: ±0.1

3. Orientation marks are indicated as follows:

G5V-2, G5V-2-H1

■Approvals

UL Recognized (File No. E41515) / CSA Certified (File No. LR31928) - - Ambient Temp. = 40°C

Note: 1.

The rated values approved by each of the safety standards may be different from the performance characteristics individually defined in this catalog.

2. In the interest of product improvement, specifications are subject to change.

Precautions

Long-term Continuously ON Contacts

Using the Relay in a circuit where the Relay will be ON continuously

for long periods (without switching) can lead to unstable contacts

because the heat generated by the coil itself will affect the insulation,

causing a film to develop on the contact surfaces. Be sure to use a

fail-safe circuit design that provides protection against contact failure

or coil burnout.

Relay Handling

When washing the product after soldering the Relay to a PCB, use a

water-based solvent or alcohol-based solvent, and keep the solvent

temperature to less than 40°C. Do not put the Relay in a cold clean-

ing bath immediately after soldering.

Type Contact form Coil rating Contact ratings

G5V-2 DPDT 3 to 48 VDC 0.6 A at 125 VAC (General Use)

0.6 A at 110 VDC (Resistive)

2 A at 30 VDC (Resistive)

G5V-2-H1 3 to 48 VDC 0.5 A at 125 VAC (General Use)

0.2 A at 110 VDC (Resistive)

1 A at 24 VDC (Resistive)

Terminal Arrangement/

Internal Connections

(Bottom View)

Mounting Holes

(Bottom View)

Tolerance: ±0.1

20.5 max.

20.3 typ.

10.1 max.

9.9 typ.

11.5 max.

11.4 typ.

0.5

3.5

7.62

0.30.5

7.62 5.08 5.08

(1.3)

7.62

(1.3)

Eight, 1-dia. holes

(1.2)

Low Signal Relay G5V-2

MEMO

Low Signal Relay G5V-2

OMRON ON-LINE

Global - http://www.omron.com

USA - http://www.components.omron.com

Cat. No. X301-E-1b Printed in USA

OMRON ELECTRONIC

COMPONENTS LLC

55 E. Commerce Drive, Suite B

Schaumburg, IL 60173

847-882-2288

09/11 Specifications subject to change without notice

All sales are subject to Omron Electronic Components LLC standard terms and conditions of sale, which

can be found at http://www.components.omron.com/components/web/webfiles.nsf/sales_terms.html

ALL DIMENSIONS SHOWN ARE IN MILLIMETERS.

To convert millimeters into inches, multiply by 0.03937. To convert grams into ounces, multiply by 0.03527.