CONNOR-WINFIELD AURORA, IL. 60505 PHONE (630) 851-4722 CORP ORATION FAX (630) 851-5040 3.3V TRI-STATE HCMOS SMD OSCILLATOR SPECIFICATIONS HMOe3 HMO033 Frequency Range 1.8MHz to SOMHz Frequency Stability +50ppm +100ppm (Inclusive of calibration tolerance at 25C, operating temperature range, input voltage change, load change, aging, shock and vibration) Temperature Range OC to +70C Waveform HCMOS Squarewave Load 15SpF Voltage Voh 2.97V Minimum Output Vol 0.33V Maximum Current loh 2mA lol 2mA Duty Cycle 40/60% Maximum measured at 50% Vdd Rise/Fall Time 6nS Maximum Jitter SpS RMS Maximum Output E/D Time Enable 10mS Maximum , Disable 150nS Maximum Input Enable Vih > 70% Vdd Minimum (Output Active) Disable vil < 30% Vec Maximum (Output High z)- Oscillator output is enabled with no connection on pin 1 Start Up Time 10mS Maximum Supply Voltage (Vdd) +35.5Vde +10% Supply Current 1.8MHz to 50MHz: 15mA Maximum Standby Current 10uA (3.50mm) .055 (1.50mm) 1 TRI-STATE E/D (1-40rmm) 2 GROUND Pa + 3 OUTPUT 237 He] [=-.028 .100 4 VDD (6.00mm) | (.71mm) (2.54mm) B27 _t ORDERING INFORMATION t HMO33__ _50.00MHz (.10mm) .005 LL : CLOCK CENTER R orm (.15mm) (1.00mm) SERIES FREQUENCY Dimensional Tolerance: +.008 (.20mm) Specifications subject to change without notice BULLETIN #; _SMOS1 rev; _O1_ PAGE a OF 27 DATE: 7/18/01 ISSUED BY: CONNOR-WINFIELD CORPORATION AURORA, IL. 60505 PHONE (630) 851-4722 FAX (630) 8515040 OUTPUT WAVEFORM TF~ - Tr +4,5Vde !2 +2.5Vde \ +0.5Vde a \ GND. LEVEL TI T0=1/fo SYMMETRY=(11/T0)x100% TEST CIRCUIT OSCILLOSCOPE PowEs PROBE SUPPLY | 5 +8 | O1uf} OSC CL 1 2 = = i = t = FREQ COUNTER INPUT FOR E/D O MECHANICAL CHARACTERISTICS FREE DROP: The specimen shall meet electrical characteristics after tested 3 times Free Drop testing on the hard wooden board from a height of 75cm. VIBRATION: The specimen shall meet electrical characteristics after tested by the following conditions; 10-55Hz 1.5mm Amplitude, 55-2000Hz 20Gs, 2 hours for each plane. THERMAL SHOCK: After applied Thermal Shock of 260 C max x 10 sec max x 2 times, or 230 C max x 180 sec max, the specimen shall meet electrical characteristics. SOLDERABILITY: (EIAJRCX0102/101 Condition 1a) . Flux: MIL-F14256 (WW Rosin=25%, Isopropyl alcohol=75%) . Solder: QQS571 (Sn=63%, Pb=37%) . Solder bath temperature: 235 C +/5 C. . Depth of immersion: Up to electrical terminal. . immersing time: Within 2 sec +/0.5 sec into solder ath. After performing the above procedures, a newly soldered coverage shall be greater than 90%. abhAD > ENVIRONMENTAL CHARACTERISTICS TEMPERATURE CYCLE: The specimen shall tested 5 cycles of HERMETICAL No bubbles gppear 125 C +/-5 meet electrical characteristics after -55 C/30 min & +125 C/30 min. in Flourinert (FC43) at , for 5 minutes. SOLVENT RESISTANCE: Marking will withsta nd immersion in Isopropyl Alcohol or Trichloroethylene. SOLDERING GENERAL CONDITIONS: 260C max x 10 s 230C max x 180 TYPICAL OPERATION DATA 20 to 100 sec up ec max x 2 times max or sec max x 1 time. (Vapor phase reflow) to 215C, 50 sec at 215C then down to room temperature per 1 to 5C/sec TAPING AND REEL | - 53 DIMENSIONS .08 08 8.45 DIA | | 15 | 9.85 32 [re MEETS EIA481A AND EIAJ1009B Z 200090000900000 oO 2 > l J w \ \ PIN 1 SUGGESTED PAD LAYOUT - mu - 1 2 VDD_ | 4 OUTPUT Cby c GROUND | 21 055 t | Le 955 TYP TYP Bypass capacitor, Cby, should be ceramic capacitor > .O1uf. - .07 Specifications subject to change 3,000 PCS/REEL 47 without notice. BULLETIN #: _ SMOS1 REV: O01 PAGE 27 OF 27 DATE: 7/18/01 ISSUED BY: