Optocoupler--DIP Package OPIA800 through OPID804 Features: * * * * 5,000 Vrms electrical isolation Choice of a Single and Dual LED Choice of Phototransistor or Photologic(R) Sensor Low-cost plastic Dual-In-Line (DIP) package Agency Approvals: * * UL Certification No: E58730 VDE pending Description: The OPIA800D through OPID804D optocouplers are designed for applications that utilize a digital output (Phototlogic(R)) in a dual-in-line package. Isolation voltage from 2,500 to 5,000 Volts RMS product are designed for some of the most stringent power system isolation requirements. Theory of operation: The LED transmitter is used to illuminate the Photosensor providing electrical isolation between two power systems while maintaining the ability to transmit information from one power system to the other. In many applications, analog or digital signals may be required to be transmitted between two power systems while maintaining isolation between the power systems up to 5,000 volts RMS. A variety of LED and photosensor configurations are available depending on the system requirements CTR = 20 mA Photosenso r - Current = * 100 = 200 10 mA LED - Current All DIP product is shipped in a shipping tube with "TU" identified on the end of the part number. Example: OPI800DTU is a 8-Pin DIP shipped in a tube (TU). Applications: * * High voltage isolation PCBoard power system isolation RoHS * * * Industrial equipment power isolation Medical equipment power isolation Office equipment OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. OPTEK Technology Inc. -- 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 sensors@optekinc.com www.optekinc.com Issue A.2 11/08 Page 1 of 20 Optocoupler--DIP Package OPIA800 through OPID804 Analog Output Devices Ordering Information Part Number Isolation Voltage Max. (Vrms) CTR Min/Typ/Max Typ. Tplh / Tphl (s) [RL = ohms] Package Configuration OPIA800 2,500 300 / 1,600 / - 7 / 2 [ 2.2 K] 8 Pin DIP A K--K A B C E (Dar) OPIA801 2,500 500 / 1,600 / - 10 / 5 [ 4.7 K] 8 Pin DIP A K--K A B C E (Dar) OPIA802 2,500 15 / 43 / - 0.3 / 0.3 [ 1.9 K] 8 Pin DIP A K--K A C E OPIA803 5,000 5 / 43 / - 0.4 / 0.3 [ 4.1 K] 8 Pin DIP A K--K A C E Digital Output Devices Ordering Information Part Number Isolation Voltage Max. (Vrms) OPID804 5,000 LED A = Anode 10K Logic K = Cathode Sensor Packaging Typ. Tplh / Tphl (ns) [RL = ohms] Typ. Tr / Tf (ns) [RL = 350 ohms] 45 / 45 [ 350] Configuration: Definition of Terms LED Identification--Sensor Identification K = Cathode 10K Inverted Logic NAND Gate A = Anode B = Base 30 / 30 Part Number Suffix: TU = Ship in Tubes, Package Configuration 8 Pin DIP A K--NAND NAND Gate C = Collector TR = Ship on Tape and Reel E = Emitter Example: OPID606DTR Pin # Part Number 1 2 3 OPIA800 A OPIA801 OPIA802 4 5 6 7 8 K E C C-B K-C A K E C C-B K-C A K E C A-B K OPIA803 A K E C A-B K OPID804 A K GND Output Enable Vcc Package Outline Dimensions and Schematics: Top-View Symbol Definition A Anode B Base C Collector E Emitter K Cathode OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. Issue A.2 11/08 Page 2 of 20 OPTEK Technology Inc. -- 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 sensors@optekinc.com www.optekinc.com Optocoupler--DIP Package OPIA800 through OPID804 Absolute Maximum Ratings (TA = 25o C unless otherwise noted) Storage Temperature Operating Temperature OPIA800 OPIA801 OPIA802 OPIA803 OPID804 Isolation voltage (1 minute) OPID804 OPIA800, OPIA801, OPIA802, OPIA803 -55 C to +125 C -40 C to +115 C 0 C to +125 C -55 C to +115 C -55 C to +100 C 0 C to +85 C Lead Soldering Temperature (1/16" (1.6 mm) from case for 5 seconds with soldering iron) 5,000 Vrms 2,500 Vrms 260 C Input Diode Continuous Forward Current OPIA802, OPIA803, OPID804 OPIA800, OPIA801 Peak Forward current (1 s pulse width, 300 pps) OPIA800, OPIA801, OPIA802, OPIA803 OPID804 Reverse Voltage OPIA800D, OPIA801D, OPIA802D, OPIA803D, OPID804D Power Dissipation OPIA802D, OPIA803D, OPID804D OPIA800D, OPIA801D 25 mA 20 mA 1A 40 mA 5V 45 mW 35 mW Absolute Maximum Ratings (TA = 0 C to 70 C unless otherwise specified) Output IC Vcc--Collector-Emitter Voltage OPIA800D OPIA801D OPIA802D, OPIA803D Collector Current OPIA802D, OPIA803D OPIA800D, OPIA801D Power Dissipation OPIA800D, OPIA801D, OPIA802D, OPIA803D -0.5 V to +7 V -0.5 V to +18 V -0.5 V to +15 V 8 mA 60 mA 100 mW Output NAND Gate--OPID804D Vcc--Supply voltage Enable voltage High Level Output voltage 7V 5.5 V 7V Low Level Output current 50 mA Output Collector Power Dissipation 85 mW OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. OPTEK Technology Inc. -- 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 sensors@optekinc.com www.optekinc.com Issue A.2 11/08 Page 3 of 20 Optocoupler--DIP Package OPIA800 through OPID804 Electrical Characteristics: OPIA800D *6 Current transfer ratio is a ratio of input current and output current expressed in %. *7 Measured as 2-pin element (Short 1,2,3,4 and 5,6,7,8) OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. Issue A.2 11/08 Page 4 of 20 OPTEK Technology Inc. -- 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 sensors@optekinc.com www.optekinc.com Optocoupler--DIP Package OPIA800 through OPID804 Switching Characteristics: OPIA800D *9 Instantaneous common mode rejection voltage "output(1)" represents a common voltage variation that can hold the output above (1) level (Vo>2.0V). *10 Instantaneous common mode rejection voltage "output(1)" represents a common voltage variation that can hold the output above (0) level (Vo>0.8V). *8 Test Circuit Propagation Delay Time *10 Test Circuit for Instantaneous Common Mode Rejection Voltage OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. OPTEK Technology Inc. -- 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 sensors@optekinc.com www.optekinc.com Issue A.2 11/08 Page 5 of 20 Optocoupler--DIP Package OPIA800 through OPID804 Electrical Characteristics: OPIA801D (TA = 25C) *6 Current transfer ratio is a ratio of input current and output current expressed in %. *7 Measured as 2-pin element (Short 1,2,3,4 and 5,6,7,8) OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. Issue A.2 11/08 Page 6 of 20 OPTEK Technology Inc. -- 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 sensors@optekinc.com www.optekinc.com Optocoupler--DIP Package OPIA800 through OPID804 Switching Characteristics: OPIA801D *9 Instantaneous common mode rejection voltage "output(1)" represents a common voltage variation that can hold the output above (1) level (Vo>2.0V). *10 Instantaneous common mode rejection voltage "output(1)" represents a common voltage variation that can hold the output above (0) level (Vo>0.8V). *8 Test Circuit Propagation Delay Time *10 Test Circuit for Instantaneous Common Mode Rejection Voltage OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. OPTEK Technology Inc. -- 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 sensors@optekinc.com www.optekinc.com Issue A.2 11/08 Page 7 of 20 Optocoupler--DIP Package OPIA800 through OPID804 Electrical Characteristics: OPIA802D (TA = 0 to +70C unless otherwise specified) *5 Current transfer ratio is a ratio of input current and output current expressed in %. *6 Io = 2.4mA *7 Measured as 2-pin element (Short 1,2,3,4 and 5,6,7,8) OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. Issue A.2 11/08 Page 8 of 20 OPTEK Technology Inc. -- 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 sensors@optekinc.com www.optekinc.com Optocoupler--DIP Package OPIA800 through OPID804 Switching Characteristics: OPIA802D (TA = 25C, VCC=5V, IF=16mA) *8 RL = 1.9k ohms is equivalent to on LSTTL and 5.6k ohm pull-up resistor. *9 Instantaneous common mode rejection voltage "output(1)" represents a common voltage variation that can hold the output above (1) level (Vo>2.0V). *10 Instantaneous common mode rejection voltage "output(1)" represents a common voltage variation that can hold the output above (0) level (Vo>0.8V). *11 Bandwidth represents a point where AC input goes down by 3dB. *9 Test Circuit Propagation Delay Time *11 Test Circuit for Instantaneous Common Mode Rejection Voltage OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. OPTEK Technology Inc. -- 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 sensors@optekinc.com www.optekinc.com Issue A.2 11/08 Page 9 of 20 Optocoupler--DIP Package OPIA800 through OPID804 Electrical Characteristics: OPIA803D (TA = 0 to +70C unless otherwise specified) *5 Current transfer ratio is a ratio of input current and output current expressed in %. *6 Io = 1.1mA *7 Measured as 2-pin element (Short 1,2,3,4 and 5,6,7,8) OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. Issue A.2 11/08 Page 10 of 20 OPTEK Technology Inc. -- 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 sensors@optekinc.com www.optekinc.com Optocoupler--DIP Package OPIA800 through OPID804 Switching Characteristics: OPIA803D (TA = 25C, VCC=5V, IF=16mA) *8 RL = 4.1k ohms is equivalent to on LSTTL and 6.1k ohm pull-up resistor. *9 Instantaneous common mode rejection voltage "output(1)" represents a common voltage variation that can hold the output above (1) level (Vo>2.0V). *10 Instantaneous common mode rejection voltage "output(1)" represents a common voltage variation that can hold the output above (0) level (Vo>0.8V). *11 Bandwidth represents a point where AC input goes down by 3dB. *9 Test Circuit Propagation Delay Time *11 Test Circuit for Instantaneous Common Mode Rejection Voltage OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. OPTEK Technology Inc. -- 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 sensors@optekinc.com www.optekinc.com Issue A.2 11/08 Page 11 of 20 Optocoupler--DIP Package OPIA800 through OPID804 (TA = 0 to +70C unless otherwise specified) Electrical Characteristics: OPID804D SYMBOL PARAMETER MIN TYP MAX UNITS TEST CONDITIONS Forward Voltage (*4) - 1.6 1.8 V IF = 10 mA, TA = 25 C BVR Reverse Breakdown Voltage 5 - - V IR = 10 A, TA = 25 C CIN Input Capacitance - 60 - pf VF = 0.0 V, f = 1M Hz IOL = 13 mA, VCC = 5.5 V, IF = 5 mA, VEH=2V Input Diode VF Output Photologic VOL Low Level Output Voltage - 0.4 0.6 V IOH High Level Output Current - 2 250 A VCC=5.5 V, VO=5.5 V, VE=2.0 V, IF=250 A IEH High Level Enable Current - -0.8 - mA VCC = 5.5 V, VE = 2.0 V IEL Low Level Enable Current -2.0 -1.2 - mA VCC = 5.5 V, VE = 2.0 V ICCL Low Level Output Current - 13 18 mA VCC = 5.5 V, VE = 0.5 V, IF = 10 mA ICCH High Level Output Current - 7 15 mA VCC = 5.5 V, VE = 0.5 V, IF = 0 mA II-O Leakage Current - - 1.0 mA VI-O = 3,000 V, TA = 25 C, t = 5 s, RH = 45% tEHL Enable Propagation delay "High to Low" (*8) - 15 ns tELH Enable Propagation delay "Low to High" (*8) - 40 - VEH = 3.0 V, VEL = 0.5 V, RL = 350 , IF = 7.5 mA, CLOAD = 15 pf Hysteresis - 0.8 - Ratio VCC = 5 V, RL = 280 RI-O Input-Output Isolation resistance (*5) - 1012 - ohm VI-O = 500 V, TA = 25 C CI-O Input-Output Capacitance (*5) - 0.6 - pf f = 1M Hz, TA = 25 C Propagation delay "High to Low" and "Low to High" (*7) - 45 75 ns tR & tF Rise and Fall Time - 30 - VCC = 5 V, RL = 350 , IF = 7.5 mA, CLOAD = 15 pf, TA = 25C CMH Instantaneous common mode rejection voltage "High Output" (*9) - 500 - CML Instantaneous common mode rejection voltage "Low Output" (*9) - -500 - IFHL / IFLH tPHL & tPLH V/us VCM = 10 V, RL = 350 , IF = 0 mA, VO = 2.0 V VCM = 10 V, RL = 350 , IF = 5 mA, VO = 0.8 V Notes: (Typical values are all at VCC = 5V, Ta = 25C. *5 Measured as 2-Pin element. Connect pins 2 and 3, connect pins 5,6,7 and 8. *6 DC current transfer ratio is defined as the ratio of output collector current to forward bias input current. *7 Refer to Figure 1. *8 Refer to Figure 2. *9 CMH represents a common mode voltage ignorable rise time ratio that can hold logic (1) state in output. CML represents a common mode voltage ignorable fall time ratio that can hold logic (0) state in output. OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. Issue A.2 11/08 Page 12 of 20 OPTEK Technology Inc. -- 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 sensors@optekinc.com www.optekinc.com Optocoupler--DIP Package OPIA800 through OPID804 Recommended Operating Conditions: OPIA804D Truth Table Figure 1. Circuit Block Diagram Test Circuit Propagation Delay Time OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. OPTEK Technology Inc. -- 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 sensors@optekinc.com www.optekinc.com Issue A.2 11/08 Page 13 of 20 Optocoupler--DIP Package OPIA800 through OPID804 Test Circuit for Enable Propagation Delay Time Figure 2. Figure 3. Test Circuit for Instantaneous Common Mode Rejection Voltage OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. Issue A.2 11/08 Page 14 of 20 OPTEK Technology Inc. -- 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 sensors@optekinc.com www.optekinc.com Optocoupler--DIP Package OPIA800 through OPID804 OPIA800 OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. OPTEK Technology Inc. -- 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 sensors@optekinc.com www.optekinc.com Issue A.2 11/08 Page 15 of 20 Optocoupler--DIP Package OPIA800 through OPID804 OPIA800 OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. Issue A.2 11/08 Page 16 of 20 OPTEK Technology Inc. -- 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 sensors@optekinc.com www.optekinc.com Optocoupler--DIP Package OPIA800 through OPID804 OPID804 OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. OPTEK Technology Inc. -- 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 sensors@optekinc.com www.optekinc.com Issue A.2 11/08 Page 17 of 20 Optocoupler--DIP Package OPIA800 through OPID804 OPID804 OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. Issue A.2 11/08 Page 18 of 20 OPTEK Technology Inc. -- 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 sensors@optekinc.com www.optekinc.com Optocoupler--DIP Package OPIA800 through OPID804 Quality / Reliability Requirements Failure Criteria Conditions 10% 11 samples after 500Hrs 0 Fail @ VCE = 5.0VDC, Ta = 70C 10% 50 samples after 96Hrs 0 Fail @ Max PD, Ta = 25C MTTF @ 90% confidence 150,000 Min. @ 25C, 25mADC Moisture Sensitivity Level MSL 1 per JDEC stnd J-STD-020B Lead Solderability 0 Fail per Method 208 of MIL-STD-202. 125C Min. DSC test method Temperature Humidity-Bias 20% 85C, 85%RH, 500Hrs, 80% min Iceo Temperature Cycle 20% per Method 1010.7 of MIL-STD-883E High Temperature Storage 20% 85C, 500Hrs Autoclave 0 Fail TA = 121C, Pressure = 15psi, Humidity = 100%, Time = 96Hrs Parameter HTRB D IC(OFF) HTFB D IC(ON) Glass Transition of body Note: This is to be performed when a change occurs to form, fit or function. Government and Industry Standard Compliance Requirements European Union's Reduction of Hazardous Substances (RoHS) Directive 2002/95/EC Label Identification: DESCRIPTION: Size: 3" (7.4 cm) X 2.2" (5.5 cm) Lettering shall be black on white background. Format shall be as: Notes: 1. The DATE CODE is a 4-digit code for date of manufacture where YY is the last two digits of the year, and WW is week number of manufacture. 2. The LOT I.D. is the manufacturing location lot identification where Y is the year of manufacture, NNNN is a sequential lot identifier, and DDD is the day of the year of manufacture. - or use equivalent label format. Carrollton, TX, USA MADE IN TAIWAN OPTEK P/N __OPIA800D-TU__ IIIIIIIIIIIIIIIIIIIII QTY. ________N/A_________ IIIIIIIIIIIIIIIIIIIII DATE CODE _____(YYWW)___ IIIIIIIIIIIIIIIIIIIII LOT I.D. ____(Y-NNNNDDD)__ IIIIIIIIIIIIIIIIIIIII OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. OPTEK Technology Inc. -- 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 sensors@optekinc.com www.optekinc.com Issue A.2 11/08 Page 19 of 20 Optocoupler--DIP Package OPIA800 through OPID804 Packaging Information: Tube Optek's Optocoupler Part Numbers Packaging Quantities 4-PIN OPIA400D/A, OPIA410D/A P/H OPIA413D/A and 6-PIN SMD OPIA6XXD/A Series 8-PIN OPIA8XXD Series and OPID804D Inner 52 x 7 x 7.5 cm Qty Small Carton Medium Carton Large Carton 53.5 x 16 x 17.5 cm 53.5 x 30.7 x 17.5 cm 53.5 x 30.7 x 25 cm Weight Qty Weight Qty Weight Gross Weight Qty Weight Gross Weight Qty Gross Weight Weig ht 100 44 3,000 1.40 12,000 6.0 6.5 24,000 12.0 12.5 36,000 18.0 18.5 65 44 1,950 1.50 7,800 6.5 7.0 15,600 12.0 12.5 23,400 18.5 19.0 48 44 1,440 1.44 5,760 6.0 6.5 11,520 12.0 12.5 17,290 18.0 18.5 100 24 6,000 1.60 24,000 6.5 7.0 48,000 13.0 13.5 72,000 19.5 20.0 170 -- 10,200 -- M/F 4-PIN and 5-PIN OPIA401B - OPIA404B, OPIA414B, OPIA500B SOP 4-PIN SSOP OPIA405C - OPIA409C P/H = Pin-Hole Packages (Referred as D = Dual-In-Line Package) SMD = Standard Surface Mount Packages (Referred as A = 6.5mil SMD) M/F or SOP = Mini-Flat Packages or Small Outside Packages (Referred as B = 4.40mil SMD w/ 2.54mil LeadSpacing) SSOP = Shrink SOP Packages (Referred as C = 3.60mil SMD with 1.27mil Lead-Spacing) Tube Packaging Specifications (TU): DIMENSIONS ARE IN: INCHES TOLERANCE: 0.008 INCHES Quantity: 8-pin: 48pcs/tube OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. Issue A.2 11/08 Page 20 of 20 OPTEK Technology Inc. -- 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 sensors@optekinc.com www.optekinc.com